dw fd tearingapartjewelryset - beadalon · seam , next to crimped cover bead, and then close it...

2
PAGE 1 ® DESIGN WORKSHOP TEARING APART JEWELRY SET Materials By: Fernando Dasilva Beadalon 14 Silver-Plated Corrugated Crimp Covers – 312B-110 32 Silver-Plated Jump Rings – 341B-117 32 Silver-Plated Sexy Tag Charms – 322B-012 2 Silver-Plated ‘s’ Hook Clasps – 313B-010 1 pair of Silver-Plated Lever Backs – 308B-014 1 Sterling Silver EZ –Crimp Toggle – 423G-010 3 ft 49 Strands .024” Silver-Plated Stringing Wire A.C.Moore: 78 6x9mm Crystal Tear Drop by Bead Collection – 40511 14 4x4mm Hematite Cubes by Bead Collection – 40185 Tools: Round Nose Pliers Chain Nose Pliers Cutters NECKLACE: 1. Cut a 2ft length of stringing wire and feed one of the tips onto coiled section of one part of toggle clasp. Use outer jaw of crimper tool to squeeze wire around the coiled section to secure the end. 2. Feed one bead onto the wire. 3. Feed one hematite cube followed by 6 crystal drops onto the wire. Repeat pattern until you have 13 cubes strung onto the wire. 4. Move all the beads against the secured toggle leaving 5 inches of stringing wire exposed, and then feed the end of the wire onto the coiled section of other half of toggle secur- ing it on same fashion done on the opposite side. 5. Place beaded section symmetrically on wire, and then use crimper tool to close one of the crimp beads to stop beads to run loosely on wire. 6. Slide crimp cover onto wire sideways through the opening seam , next to crimped cover bead, and then close it over the wire. 7. Squeeze last crimp bead of the other side of the necklace to confine beaded section. Add a second crimp bead on same fashion done on step 6. 8. Open a jump ring, scoop up a silver-plated tag and start adding to the body of the necklace, placing it in the middle of crystal drop sections. Repeat throughout the length of beaded section until you have all 13 tags on wire.

Upload: others

Post on 12-Jun-2020

2 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: DW FD TearingApartJewelrySet - Beadalon · seam , next to crimped cover bead, and then close it over the wire. 7. Squeeze last crimp bead of the other side of the necklace to con˜

PAGE 1

®

DESIGN WORKSHOP

TEARING APART JEWELRY SET

Materials

By: Fernando Dasilva

Beadalon• 14 Silver-Plated Corrugated Crimp Covers – 312B-110• 32 Silver-Plated Jump Rings – 341B-117• 32 Silver-Plated Sexy Tag Charms – 322B-012• 2 Silver-Plated ‘s’ Hook Clasps – 313B-010• 1 pair of Silver-Plated Lever Backs – 308B-014• 1 Sterling Silver EZ –Crimp Toggle – 423G-010• 3 ft 49 Strands .024” Silver-Plated Stringing Wire

A.C.Moore:• 78 6x9mm Crystal Tear Drop by Bead Collection – 40511• 14 4x4mm Hematite Cubes by Bead Collection – 40185

Tools:• Round Nose Pliers• Chain Nose Pliers• Cutters

NECKLACE:

1. Cut a 2ft length of stringing wire and feed one of the tips onto coiled section of one part of toggle clasp. Use outer jaw of crimper tool to squeeze wire around the coiled section to secure the end.

2. Feed one bead onto the wire.

3. Feed one hematite cube followed by 6 crystal drops onto the wire. Repeat pattern until you have 13 cubes strung onto the wire.

4. Move all the beads against the secured toggle leaving 5 inches of stringing wire exposed, and then feed the end of the wire onto the coiled section of other half of toggle secur-ing it on same fashion done on the opposite side.

5. Place beaded section symmetrically on wire, and then use crimper tool to close one of the crimp beads to stop beads to run loosely on wire.

6. Slide crimp cover onto wire sideways through the opening seam , next to crimped cover bead, and then close it over the wire.

7. Squeeze last crimp bead of the other side of the necklace to con� ne beaded section. Add a second crimp bead on same fashion done on step 6.

8. Open a jump ring, scoop up a silver-plated tag and start adding to the body of the necklace, placing it in the middle of crystal drop sections. Repeat throughout the length of beaded section until you have all 13 tags on wire.

Page 2: DW FD TearingApartJewelrySet - Beadalon · seam , next to crimped cover bead, and then close it over the wire. 7. Squeeze last crimp bead of the other side of the necklace to con˜

PAGE 2

EARRINGS:

1. Cut a 7-inch piece of stringing wire.

2. Use outer jaw of crimper tool to close 8 crimp covers and set them aside.

3. Follow pattern given to string beads: 2 crimp covers + 1 hematite cube + 3 crystal dropsRepeat pattern until you have four crimp covers strung on wire.

4. Feed both ends of the wire onto a single crimp tube form-ing a drop shape hoop.

5. Squeeze crimp tube with crimper and trim excess wire.

6. Attach a silver-plated ‘s hook’ through the middle of dan-gle.

7. Open a jump ring and attach to ‘s hook’ component and to a lever back ring.

8. Repeat on steps to make matching earring.

BRACELET:

1. Cut a 7-inch piece of stringing wire and use EZ-lobster clasp to secure one end.

2. Use necklace similar technique to assemble v bracelet. Follow stringing pattern given below: 1 crimp cover + 3 hematite cubes + 3 b crystal drops Repeat pattern until you have 13 cubes strung on wire.

3. Open a jump ring, scoop up a silver-plated tag and add randomly throughout the length of bracelet, on same fash-ion done on necklace.