dv series direct-fired makeup air heaters - reznorparts.com · for service on control side of unit...
TRANSCRIPT
Form P-DV, Page 1
IMPORTANT1. Always include complete heater model and serial number so
that any specification change can be considered for parts ship-
ment. It can save time and expense.
2. Specifications are subject to change without notice.
3. We reserve the right to substitute functional replacements.
4. Order either by Kit or Component Part No.Replacement Parts Form RZ-NA P-DV (Version A)
Obsoletes Form RGM-741 and Form P-DV
APPLIES TO: Model DV
DV SeriesDirect-Fired
Makeup Air Heaters
Rating Plate and Serial No.Sample of a Rating Plate
BlowerSection
Burner/Control Section
Location for OptionalFilter Cabinet (not shown)
Screened Inlet Base
HorizontalDischarge
Air
OptionalReturn Air
OutsideAir
Model DV
ADDITIONAL REFERENCES:• Installation Form I-DV
• Operation/Maintenance/Service Form O-DV/RDF/ADF
Website: www.RezSpec.com (Forms are available to download.)
®
Rating Plate Codes:
A = Model No.
B = Gas Type (Nat or LP)
C = Motor HP
D = Volt
E = Phase
F = Maximum Total Input
Amps for Unit
G = SCFM
H = ESP
I = CFM
J = Maximum Input
K = Minimum Input
L = Manifold Presssure
M = Minimum Inlet
Pressure
N = Maximum Supply
Pressure
P = Wiring Diamgram No.
Q = Maximum Discharge
Temperature
Z = Maximum Temperature
Rise °F
REZNORMERCER, PA. USA 16137
ANSI Z83.4B/CSA 3.7B-2002 NON-RECIRCULATING DIRECT-FIRED
INDSTRIAL AIR HEATER
ANSI Z83.4B/CSA 3.7B-2002 RADIATEUR INDSTRL SANS CIRCUL. D'AIR
FOR INDUSTRIAL/COMMERCIAL USE ONLYFOR EITHER INDOOR OR OUTDOOR INSTALLATIONINSTALLER À L'INTÉRIEUR OU À L'EXTÉRIEUR
MODEL { A } SERIAL # { computer generated }GAS TYPE { B } MOTOR HP { C }VOLTAGE { D } PHASE { E } 60 HZMAX TOTAL INPUT AMPS FOR THE UNIT { F }WIRING DIAGRAM NUMBER: { P }
UNIT IS EQUIPPED FOR { G } SCFM AGAINST { H } IN WC ESP
WITH A MAX DISCH TEMP OF { Q } oF AND A MAX TEMP RISE OF{ Z } oF AND CANNOT BE USED BELOW -40 oF
CONCU POUR { X } M3 CONTRE UNE PRESSION STATIQUEXTERNE DE { W } KPA (PO C.E.) WITH A MAX DISCHARGE TEMP OF
{ Y } oC AND A MAX TEMP RISE OF { AA } oC AND CANNOT BE USED
BELOW -40 oC.
MAXIMUM INPUT RATING BTU/HRMINIMUM INPUT RATING BTU/HRNORMAL MANIFOLD PRESS. IN WCMIN GAS INLET PRESS. FOR BURN. ADJ. IN WCMAX PERMISSIBLE GAS SUPPLY PRESS. PSIMIN PRESSURE DROP ACROSS BURNER IN WCMAX PRESSURE DROP ACROSS BURNER IN WC
MAXIMUM INPUT RATING KW/HRMINIMUM INPUT RATING KW/HRNORMAL MANIFOLD PRESS. KPAMIN GAS INLET PRESS. FOR BURN. ADJ. KPAMAX PERMISSIBLE GAS SUPPLY PRESS. KPA
MIN PRESSURE DROP ACROSS BURNER KPAMAX PRESSURE DROP ACROSS BURNER KPA
CLEARANCES TO COMBUSTIBLES:
TOP, BOTTOM, AND SIDE OPPOSITE CONTROLS - 1 INCH
FOR SERVICE ON CONTROL SIDE OF UNIT - WIDTH OF UNIT
{ S }{ T }
{ J }{ K }{ L }
{ M }
0.1875
{ N }0.250.75
{ R }
{ U }{ V }
0.0625
Index by Page No.Amplifier 9 Limit Controls 3
Belts 15-20 Maxitrol System Components 9
Blowers 14 Mixing Tube 9
Burners 12 Motor Mounting 14
Cabinet Parts - Blower Section 21 Motors (Blower) 6-8
Cabinet Parts - Burner Section 22 Motors (Damper) 13
Cabinet Parts - Filter Section 24 Overhead Door Switch 3-4
Cabinet Parts - Inlet Base 23 Pilot 12
Contactor (Motor) 6 Potentiometer 13
Convenience Outlet 4 Pressure Switches (Air) 3-4
Damper Controls 13 Pressure Switches (Gas) 10-11
Dampers - Bypass 13 Pulley 15-20
Dampers - Discharge 13 Quick Connect 3-4
Dampers - Inlet 13 Rating Plate 1
Dampers - Return Air 13 Regulator (Gas Train) 11
Dirty Filter Pressure Switch 3-4 Regulator (Gas Supply) 11
Disconnect Switch 5 Relays 3
Drives 15-20 Remote Console 5
Duct Connector (Flexible) 21 Serial No. 2
Electrical Compartment 2 Signal Conditioner 9
Filters - Filter Section 24 Smoke Detector 3-4
Filters - Inlet Base 23 Starters 6-8
Firestat 3-4 Starter Holding Coils 8
Flame Sensor 12 Starter Overloads 6-8
Freezestat 3 Starter Relay 3
Fuseholder and Fuses 4 Switches (Electrical) 3-4
Gas Train Components 10 Temperature Selector 9
Ignition Module 12 Temperature Sensor 9
Ignitor 12 Transformer 4
Inlet Air Base 23 Water Separator 23
Lights (Circuit Board) 3 Vibration Isolation (Motor) 14
Lights (Remote Console) 5 Valves 10-11
Form P-DV, Page 2
Electrical Components
Rating Plate and Serial No. (cont'd)
First Element of the Serial Number - Date of Manufacture
Year Jan Feb Mar Apr May June July Aug Sept Oct Nov Dec
1998 AXA AXB AXC AXD AXE AXF AXG AXH AXI AXJ AXK AXL
1999 AYA AYB AYC AYD AYE AYF AYG AYH AYI AYJ AYK AYL
2000 AZA AZB AZC AZD AZE AZF AZG AZH AZI AZJ AZK AZL
2001 BAA BAB BAC BAD BAE BAF BAG BAH BAI BAJ BAK BAL
2002 BBA BBB BBC BBD BBE BBF BBG BBH BBI BBJ BBK BBL
2003 BCA BCB BCC BCD BCE BCF BCG BCH BCI BCJ BCK BCL
2004 BDA BDB` BDC BDD BDE BDF BDG BDH BDI BDJ BDK BDL
2005 BEA BEB BEC BED BEE BEF BEG BEH BEI BEJ BEK BEL
2006 BFA BFB BFC BFD BFE BFF BFG BFH BFI BFJ BFK BFL
2007 BGA BGB BGC BGD BGE BGF BGG BGH BGI BGJ BGK BGL
2008 BHA BHB BHC BHD BHE BHF BHG BHH BHI BHJ BHK BHL
2009 BIA BIB BIC BID BIE BIF BIG BIH BII BIJ BIK BIL
2010 BJA BJB BJC BJD BJE BJF BJG BJH BJI BJJ BJK BJL
2011 BKA BKB BKC BKD BKE BKF BKG BKH BKI BKJ BKK BKL
2012 BLA BLB BLC BLD BLE BLF BLG BLH BLI BLJ BLK BLL
2013 BMA BMB BMC BMD BME BMF BMG BMH BMI BMJ BMK BML
2014 BNA BNB BNC BND BNE BNF BNG BNH BNI BNJ BNK BNL
2015 BOA BOB BOC BOD BOE BOF BOG BOH BOI BOJ BOK BOL
Electrical Compartment Location Drawing
CODE 1,Circuit Board
CODES 2-5,Control Relays
CODE 9,Outside Air Cutoff
(high ambient limit control)
Code 231,BypassDamperMotor
CODE 121,Return AirDamper Motor(page 13)
CODE 6, TimeDelay Relay
CODE 100,Ignition
Controller(page 12)
CODE 62,Amplifier or Signal
Conditioner(page 9)
CODE1A,StatusLights
CODE 18,Optional
Dirty FilterPressure
Switch CODES 14 and 15,Optional Bypass Damper
Pressure Switches
CODES 13 and 12,Standard AirPressure Switches
High Low
CODE 7,Starter Relays Line Voltage Terminals
CODE 47,Motor Starterwith Overloads(page 6)
CODE29,Trans-former
24-V
olt
Ter
min
als
Terminals
Serial No.
Example:
AYH 61 K2 N 12345 CA MV7
1 2 3 4 5 6 7
Codes:1 = Date of manufacture
(see chart below)
2 = Type of pilot
3 = Type of valve
4 = Type of gas (N= Natural;
L= Propane)
5 = Consecutive number
6 = Type of air control (CA = Constant Air Volume; VA
= Variable Air Volume; RA = Recirculation Air)
7 = Type of Maxitrol Gas Control (MV7 = Maxitrol
System 14; MV8 = Maxitrol System 14A or 14B;
MV9 = Maxitrol System 44; MVB = Maxitrol
System 94; MVC = Maxitrol A200)
Form P-DV, Page 3
CODE 2B - Relay,P/N 14747
CODE 3B - Relay,P/N 103317
CODE 4B -Relay,P/N 103319
CODE 6 - TimeDelay Relay(Freezestat),P/N 89661
CODE 5 -Relay,P/N103318
Electrical Components
CODE 1A, ReplacementLight for Circuit AnalyzerBoard - P/N 125189beginning 9/03; prior to9/03, P/N 101889
CODE 1B, ReplacementRelay for Board,P/N 151271
CODE 1 - Circuit AnalyzerBoard, P/N 151263
CODE 8 - Manual ResetLimit with CapillarySensor, 190°F, P/N161437; 205°F, 161433
CODES 9 and 10, P/N 126170, HighAmbient Cutoff and Freezestat
Grommet
Clamp, P/N
131993;
Cable Clamp,
P/N 132065
1 3
2 4
(Illustrations continued on page 4)
CODE 7 - Starter Relay forSingle and 2-Speed Starters(Options AN10 and AN12),P/N 110656
CODE Description Location P/N
1 PC Board Assembly (circuit board with diagnostic lights, See Code 1A) 151263
1A Replacement Light for PC Board Assembly (Code 1) 125189
1B Replacement Relay for PC Board Assembly (Code 1) 151271
2A Hamilton Standard #84-20102-101 14747
2B Hamilton Standard #134-20102-101 98118
3A Hamilton Standard #84-20103-301 18549
3B Products Unltd 9400-04-Q180 103317
4A Hamilton Standard #84-50202-101 86982
4B Hamilton Standard #134-50202-101 103319
5A Hamilton Standard #84-50203-301 90205
5B Hamilton Standard #134-50203-301 103318
6 Time Delay Relay (for freezestat bypass), T & B Agastat #VTM1ULA Electrical Compartment 89661
7 Starter Relay, Essex #91-102006-13088, SPDT, 24V coil Electrical Compartment 110656
Manual Reset Limit with Capillary Sensor, 190°F - Sizes 109 - 122 Blower Section 161437
Manual Reset Limit with Capillary Sensor, 205°F - Size 125 Blower Section 161433
9 High Ambient Cutoff, J/C #A19AAF-12C Electrical Compartment 126170
10 Freezestat, J/C #19AAF-12C Blower Compartment 126170
11 Firestat, Honeywell #L4029E1029, 200oF Blower Discharge 42782
Low Air Pressure Switch, IS2-0233-5275 (for units mfgd beginning 9/03) 207178
Low Air Pressure Switch Kit replaces P/N 86986, #FS4197-166 or PPS10175-3043 193806
High Air Pressure Switch, IS2-0233-5273 (for units mfgd beginning 9/03) 207176
High Air Pressure Switch Kit replaces P/N 86987, #FS4197-164 or PPS10175-3041 193807
Air Pressure Switch, IS2-0233-5274 (for units mfgd beginning 9/03) 207177
Bypass Air Pressure Switch Kit replaces P/N 87250, #FS4197-165 or PPS10175-3042 193809
Air Pressure Switch, IS2-0233-5276 (for units mfgd beginning 9/03) 207179
Air Pressure Switch Kit replaces P/N 87249, #FS4197-171 or PPS10175-3044 193808
15 Bushing and Insect Screen for Sensing Probes (not illustrated) 96794
16 Contactor, Furnace 42AF25AJ, 24V (used with manifold Option BM80 and BM81) Electrical Compartment 203935
17 Convenience Outlet Receptacle, Hubbell #GF5352-1 Control Compartment 96912
18 Dirty Filter Pressure Switch, Tri-Delta #AP4434, set at .3" w.c. (remote console option) Electrical Compartment 105507
19 Door Switch, Honeywell Micro-Switch #LLSNIA-3P (Option BX1) Space (on overhead door) 124253
20 DPDT System Switch, Summer/Off/Winter Space (Remote Console) 101900
21 SPDT Toggle Switch, on/on Space (Remote Console) 101901
22 24-pin connector for male wire harness that is part of quick connect (Option BB4) 158756
23 24-pin connector for female wire harness that is part of quick connect (Option BB4) 158757
24 Photoelectric Air Duct Smoke Detector, DH100ACDCP (Option SA1) Ductwork 159553
Optional quick connect between
burner/control section & blower
8
RBM Relay, SP-ST,
24V Coil
Codes 1A&B are
interchangeable.Control Compartment
RBM Relay, SP-DT,
24V Coil
Codes 2A&B are
interchangeable.Control Compartment
RBM Relay, SP-ST,
120V Coil
Codes 3A&B are
interchangeable.
Electrical Compartment
12
13
14A Electrical Compartment
RBM Relay, SP-DT,
120V Coil
Codes 4A&B are
interchangeable.Control Compartment
Control Compartment
14B Electrical Compartment
Electrical Compartment
Electrical Compartment
Form P-DV, Page 4
CODE 26,20 AmpFuse, P/N159844
CODE 27,TerminalBlock,P/N 144972
Used in both the
Electrical
Compartment and the
Remote Console
Used in both the
Electrical
Compartment and
the Remote Console
CODE 28, MountingAdapter forTerminal Block,P/N 144973
CODE Description Location P/N
25 Fuseholder Electrical Compartment 60241
26 Fuse, 20 Amp, Fusetron Electrical Compartment 159844
27 Terminal Block, #KT3 Electrical Compartment & Remote Console 144972
28 Terminal Block Mounting Adapter, KAD Electrical Compartment & Remote Console 144973
29 Transformer Electrical Compartment see below
Remote ConsoleNote: Console height changed 10/01. Console parts listed are currently manufactured size.
3637
20
38
CODE 25,Fuseholder,P/N 60241
Electrical Components (cont'd)
Sampling Tube, P/N 159714
CODE 20, DPDTSystem Switch,P/N 101900(winter/off/summer)
CODE 19,DoorSwitch,P/N124253,OptionBX1
CODE 21,SPDT Switch,P/N 101901
CODES 22and 23 - PinConnectorfor OptionBB4
CODE 23, P/N158757, Female
Connector
CODE 22, P/N 158756,Male Connector
CODE 24, Photoelectric SmokeDetector, P/N 159553 (Same asOption SA1)
CODE 18 - Dirty FilterPressure Switch,P/N 105507 (replaces
P/N 102773)
CODE 14A- AirPressureSwitch,P/N 207177
CODE 14B -Air PressureSwitch,P/N 207179
CODE 17 -ConvenienceOutlet Receptacle,P/N 96912
Replace pressure switch P/N
87250 with Kit P/N 193809.
Replace pressure switch P/N 87249
with Kit P/N 193808.
Replace pressure switch P/N
86986 with Kit P/N 193806.
CODE 13 -High AirPressureSwitch,P/N 207176
Replace pressure switch P/N
86987 with Kit P/N 193807.
CODE 11- Firestat,P/N42782
CODE 12 -Low AirPressureSwitch,P/N 207178
Volts In Volts Out VA Manufacturer's No. Reznor P/N
208/230/460 24 200 Seimens #MT0200JX24 39095
208/230/460/575 110 275 Cutler-Hammer #C0275E5E 105202
120 24 200 NSC-24H9-0908 124002
120 24 500 Hevi-Duty T5005 159842
208/230/460 24 500 Hevi-Duty T500ck 159843
CODE 29 -Transformers
200-500 VA
CODE 16 -Contactor,P/N 203935
Form P-DV, Page 5
CODE Description P/N
35 Remote Console Box 9-15/16" x 6-5/8" x 2-/8" 107010
Remote Console Box 14-15/16" x 6-5/8" x 2-5/8" 107011
36 Mounting Ring for 9-15/16" long box 107014
Mounting Ring for 14-15/16" long box 107015
37 Light with red lens, Solico #5TD1L-R-B5 101889
20 DPDT Switch, Summer/Off/Winter 101900
21 SPDT Switch, Spray/Dry 101901
38 Potentiometer, Honeywell 112894FA 16110
CODE 35 - Console Box CODE 37 -Red Light forRemoteConsole,P/N 101889
2-3/8(60)
6 (152)5-15/32 (139)
1-5/16 (33)
1-3/32 (28)4-7/16(113)
1-3/32 (28)
Temperature
Selector or
Sensor **L**** H**** D
Yes 3 Yes No 10-13/16 7-3/8 2-5/8
Yes 3 No No 10-13/16 7-3/8 2-5/8
Yes 3 Yes Yes 15-13/16 7-3/8 2-5/8
Yes 3 No Yes 10-13/16 7-3/8 2-5/8
Yes 4 Yes No 15-13/16 7-3/8 2-5/8
Yes 4 No Yes 15-13/16 7-3/8 2-5/8
Yes 4 Yes Yes 15-13/16 7-3/8 2-5/8
Yes 4 No No 15-13/16 7-3/8 2-5/8
* 3 - Blower On, Burner On, and Safety Lockout;
4th light is Dirty Filter Indicator
** On the console with Gas Control Options AG 30, 31, 32, 33, 47, 48, 51
*** On the console with Air Control Options AR19 or AR22
**** Subtract 7/8" when recessing
Technical Data of the Remote Console (Variations depend on options selected; consult
custom wiring diagram for controls and to determine wiring required.)
Dimensions (inches)Control
Switch
Qty of
Lights*
Potentiometer
***
Disconnect SwitchCODE 40,DisconnectSwitches (Sameas CP Options)
V/Ph HPApprox
FLACP V/Ph HP
Approx
FLACP
115/1 1/4 9.3 1, 2, 5, 6 460/3 1/4 1.85 3, 4, 7, 8
1/3 9.7 1, 2, 5, 6 or 1/3 1.9 1, 2, 5, 6
1/2 13.0 1, 2, 5, 6 575/3 1/2 2.1 3, 4, 7, 8
3/4 15.2 1, 2, 5, 6 3/4 2.4 3, 4, 7, 8
1 17.2 1, 2, 5, 6 1 2.5 3, 4, 7, 8
1-1/2 19.2 1, 2, 5, 6 1-1/2 3.8 3, 4, 7, 8
2 24.6 1, 2, 5, 6 2 4.4 3, 4, 7, 8
208/1 1/4 4.7 1, 2, 5, 6 3 5.3 3, 4, 7, 8
or 1/3 5.6 1, 2, 5, 6 5 7.7 3, 4, 7, 8
230/1 1/2 7.5 1, 2, 5, 6 7-1/2 11.6 3, 4, 7, 8
3/4 8.7 1, 2, 5, 6 10 14.1 3, 4, 7, 8
1 9.9 1, 2, 5, 6 15 20.6 3, 4, 7, 8
1-1/2 10.7 1, 2, 5, 6 20 27.6 3, 4, 7, 8
2 12.6 1, 2, 5, 6
3 14.8 1, 2, 5, 6
5 30.4 17, 21, 27, 30
7-1/2 40.4 17, 21, 27, 30
10 44.4 17, 21, 27, 30
208/3 1/4 3.8 1, 2, 5, 6
or 1/3 4 1, 2, 5, 6
230/3 1/2 4.5 1, 2, 5, 6
3/4 5.3 1, 2, 5, 6
1 6.1 1, 2, 5, 6
1-1/2 8.0 1, 2, 5, 6
2 9.4 1, 2, 5, 6
3 11.5 1, 2, 5, 6
5 15.9 1, 2, 5, 6
7½ 24.4 1, 2, 5, 6
10 32.4 17, 21, 27, 30
15 45.5 17, 21, 27, 30
20 61.4 18, 22, 28, 31
Cross-Reference for Selecting Option CP Disconnect SwitchDescription Option P/N
Indoor, 30 Amp, 240V, non-fusible CP1 161451
Indoor, 30 Amp, 240V, fusible CP2 161452
Indoor, 30 Amp, 600V, non-fusible CP3 161453
Indoor, 30 Amp, 600V, fusible CP4 161454
Raintight, 30 Amp, 240V, non-fusible CP5 161455
Raintight, 30 Amp, 240V, fusible CP6 161456
Raintight, 30 Amp, 600V, non-fusible CP7 161457
Raintight, 30 Amp, 600V, fusible CP8 161458
Raintight, 60 Amp, 240V, fusible CP17 161459
Raintight, 100 Amp, 240V, fusible CP18 161460
Raintight, 200 Amp, 240V, fusible CP19 166465
Raintight, 60 Amp, 600V, fusible CP20 161461
Indoor, 60 Amp, 240V, non-fusible CP21 161462
Indoor, 100 Amp, 240V, non-fusible CP22 161463
Indoor, 60 Amp, 600V, non-fusible CP23 161464
Indoor, 100 Amp, 600V, non-fusible CP24 164330
Indoor, 100 Amp, 600V, fusible CP25 161465
Indoor, 200 Amp, 240V, non-fusible CP26 166466
Indoor, 60 Amp, 240V, fusible CP27 161467
Indoor, 100 Amp, 240V, fusible CP28 161468
Indoor, 200 Amp, 240V, fusible CP29 166467
Raintight, 60 Amp, 240V, non-fusible CP30 161469
Raintight, 100 Amp, 240V, non-fusible CP31 162834
Raintight, 200 Amp, 240V, non-fusible CP32 166468
Indoor, 60 Amp, 600V, fusible CP33 162835
NOTE: Fuses are not included with disconnect switches.
Form P-DV, Page 6
Blower Motors, Contactor, and StartersCODE 45 - Blower MotorMotors in the table below that do not have a CODE 46 contactor listed do not have internal
overload protection and MUST be used with the CODE 47 motor starter and starter overload.
If a CODE 46 contactor is listed, motor may be used with either the contactor or the optional
starter and overload.
CODE 46 - Replacement Contactor (Option AN2)Motor contactor, P/N 119625, Mfr #42AF35AJ-24V coil
CODE 47 - Replacement Starter and Overloads (Option AN10)When ordering a replacement IEC starter or overload, check the manufacturer's number on both
parts. If the number is different than that listed, both components must be replaced. IEC Starter
(contactor) and overload are mounted on rail, P/N 111387.
CODE 46 CODE 47
StarterOverload
Contactor
(Located in the electrical compartment; see
location on page 3.)
Service Power
Type HP P/N Model No. Frame fla Factor Factor Mfr No. P/N min max GE # P/N Mfr No. P/N
OPEN 1/4 210611 BF2024 48/56 4.6 1/2" 115 1 1.35 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1/4 210611 BF2024 48/56 2.3 1/2" 208 1 1.35 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
OPEN 1/4 210611 BF2024 48/56 2.3 1/2" 240 1 1.35 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
OPEN 1/4 115864 H200 K48 1.1 1/2" 208 3 1.35 72 74% CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
OPEN 1/4 115864 H200 K48 1.4 1/2" 240 3 1.35 72 74% CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
OPEN 1/4 115864 H200 K48 0.75 1/2" 480 3 1.35 72 81% CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
OPEN 1/3 202091 BF2034 48 6.0 1/2" 115 1 1.35 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1/3 202091 BF2034 48 3.0 1/2" 208 1 1.35 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 1/3 115863 H260 K48 1.4 1/2" 208 3 1.35 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 42AF35AJ-24V 119625
OPEN 1/3 115863 H260 K48 1.6 1/2" 240 3 1.35 CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 ============ ===
OPEN 1/3 115863 H260 K48 0.8 1/2" 480 3 1.35 CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
OPEN 1/2 102627 BF2054 56Z 8.8 5/8" 120 1 1.15 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 42AF35AJ-24V 119625
OPEN 1/2 102627 BF2054 56Z 5.1 5/8" 208 1 1.15 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1/2 102627 BF2054 56Z 4.4 5/8" 240 1 1.15 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1/2 159183 H880 LA56 2.5 5/8" 208 3 1.25 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
OPEN 1/2 159183 H880 LA56 3.0 5/8" 240 3 1.25 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 1/2 159183 H880 LA56 1.5 5/8" 480 3 1.25 CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 42AF35AJ-24V 119625
OPEN 1/2 202089 H991 H56 0.9 5/8" 575 3 1.25 CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
OPEN 3/4 93548 312P629 B56 11.0 5/8" 120 1 1.25 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
OPEN 3/4 93548 312P629 B56 6.3 5/8" 208 1 1.25 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 3/4 93548 312P629 B56 5.5 5/8" 240 1 1.25 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 3/4 36951 312P696 D56 2.9 5/8" 208 3 1.25 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 3/4 36951 312P696 D56 2.6 5/8" 240 3 1.25 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
CODE 46 - ContactorCODE 45 -Motorph Efficiency %Shaft Volt
Starter OverloadCODE 47 - Starter
OPEN 3/4 36951 312P696 D56 1.3 5/8" 480 3 1.25 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 42AF35AJ-24V 119625
OPEN 3/4 202090 H992 H56 1.0 5/8" 575 3 1.25 CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
OPEN 1 13685 C523 H56 13.0 5/8" 120 1 1.25 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
OPEN 1 13685 C523 H56 7.5 5/8" 208 1 1.25 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 1 13685 C523 H56 6.5 5/8" 240 1 1.25 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 1 36580 H882 F56 3.7 5/8" 208 3 1.15 79% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 1 36580 H882 F56 3.2 5/8" 240 3 1.15 79% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 1 36580 H882 F56 1.6 5/8" 480 3 1.15 79% CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 42AF35AJ-24V 119625
OPEN 1 158175 E1006 N143T 1.1 7/8" 575 3 1.15 82.50% CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
OPEN 1.5 194202 C621 56 15.0 5/8" 120 1 1.2 86.4 77.20% CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
OPEN 1.5 194202 C621 56 7.8 5/8" 208 1 1.2 86.4 77.20% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 1.5 194202 C621 56 7.5 5/8" 240 1 1.2 86.4 77.20% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 1.5 115859 H884 UA56 5.6 5/8" 208 3 1.15 66.4 78.60% CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1.5 115859 H884 UA56 5.0 5/8" 240 3 1.15 66.4 78.60% CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 1.5 115859 H884 UA56 2.8 5/8" 480 3 1.15 66.4 78.60% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 1.5 158162 E1007 R145T 1.6 7/8" 575 3 1.15 85.3 84.00% CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 ============ ===
OPEN 2 202581 RB1204A 56 24.6 7/8" 120 1 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 42AF35AJ-24V 119625
OPEN 2 202581 RB1204A 56 12.3 7/8" 208 1 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
OPEN 2 202581 RB1204A 56 12.3 7/8" 240 1 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
OPEN 2 159327 H886 56HZ 7.0 7/8" 208 3 1.15 67 79% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 2 159327 H886 56HZ 6.6 7/8" 240 3 1.15 67 79% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
OPEN 2 159327 H886 56HZ 3.5 7/8" 480 3 1.15 67 79% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
OPEN 2 158176 E1008 P145T 2.1 7/8" 575 3 1.15 86 84.00% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 ============ ===
OPEN 3 111560 B735 L56 13.7 5/8" 208 1 1.15 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 3 111560 B735 L56 12.4 5/8" 230 1 1.15 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 3 159185 H845 P56HZ 9.0 7/8" 208 3 1.15 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 42AF35AJ-24V 119625
OPEN 3 159185 H845 P56HZ 8.6 7/8" 240 3 1.15 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 42AF35AJ-24V 119625
OPEN 3 159185 H845 P56HZ 4.3 7/8" 480 3 1.15 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
OPEN 3 120019 H954 N56HZ 3.6 7/8" 575 3 1.15 80.3 83.80% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
OPEN 5 111562 V211 L184T 28.3 1-1/8" 208 1 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
OPEN 5 111562 V211 L184T 25.6 1-1/8" 240 1 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
OPEN 5 113371 196033 Y56HZ 13.4 7/8" 208 3 1.15 87.2 85% CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 5 113371 196033 Y56HZ 13.2 7/8" 240 3 1.15 87.2 85% CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 5 113371 196033 Y56HZ 6.6 7/8" 480 3 1.15 87.2 85% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 ============ ===
OPEN 5 120020 H956 Y56HZ 5.4 7/8" 575 3 1.15 85.9 85.30% CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
OPEN 7.5 105828 V305 S215T 35.4 1-3/8" 208 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
OPEN 7.5 105828 V305 S215T 32.0 1-3/8" 230 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
OPEN 7.5 105854 E302 F213T 22.5 1-3/8" 208 3 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
OPEN 7.5 105855 E300 213T 19.4 1-3/8" 240 3 CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
OPEN 7.5 105855 E300 213T 9.7 1-3/8" 480 3 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 ============ ===
OPEN 7.5 158164 E324 S213T 7.8 1-3/8" 575 3 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 ============ ===
OPEN 10 105830 V303 S215T 42.0 1-3/8" 208 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
OPEN 10 105830 V303 S215T 38.0 1-3/8" 230 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
Form P-DV, Page 7(continued on page 8)
TEFC 1 174993 159105 L56 12.0 5/8" 120 1 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
TEFC 1 174993 159105 L56 6.2 5/8" 208 1 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 1 174993 159105 L56 6.0 5/8" 240 1 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 1 16080 H524 J56 3.3 5/8" 208 3 1 74.4 80.20% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
TEFC 1 16080 H524 J56 3.4 5/8" 240 3 1 74.4 80.20% CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
TEFC 1 16080 H524 J56 1.7 5/8" 480 3 1 74.4 80.20% CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 42AF35AJ-24V 119625
TEFC 1 105570 H525 H56 1.4 5/8" 575 3 1.15 71.6 80.40% CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
TEFC 1.5 94347 311P402 TK56H 16.4 5/8" 120 1 CL02A310T-1 151277 14.50 18.00 RTA1-S 151196 42AF35AJ-24V 119625
TEFC 1.5 94347 311P402 TK56H 9.5 5/8" 208 1 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 42AF35AJ-24V 119625
TEFC 1.5 94347 311P402 TK56H 8.2 5/8" 240 1 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 42AF35AJ-24V 119625
TEFC 1.5 101286 H535 L56H 4.3 5/8" 208 3 1 80.9 82.40% CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 1.5 101286 H535 L56H 4.4 5/8" 240 3 1 80.9 82.40% CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 1.5 101286 H535 L56H 2.2 5/8" 480 3 1 80.9 82.40% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1.5 105665 E127 M145T 1.6 7/8" 575 3 1.15 85.7 84% CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 ============ ===
TEFC 2 105572 K200 F182T 24 1-1/8" 120 1 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
TEFC 2 205881 L3516TM F182T 8.3 7/8" 240 1 1.15 99 78% CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
TEFC 2 158165 E166 145T 7.0 7/8" 208 3 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 ============ ===
TEFC 2 158165 E166 145T 5.8 7/8" 240 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
TEFC 2 158165 E166 145T 2.9 7/8" 480 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
TEFC 2 158166 E169 145T 2.3 7/8" 575 3 CL00A310T-1 151275 1.90 2.70 RTA1-J 151189 ============ ===
TEFC 3 111564 K222 F184T 30.0 1-1/8" 120 1 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
TEFC 3 111564 K222 F184T 15.0 1-1/8" 240 1 CL02A310T-1 151277 14.50 18.00 RTA1-S 151196 ============ ===
TEFC 3 159330 B - M3559T 145T 7.9 7/8" 208 3 CL00A310T-1 151275 5.50 8.50 RTA1-N 151192 ============ ===
TEFC 3 159330 B - M3559T 145T 7.2 7/8" 240 3 CL00A310T-1 151275 5.50 8.50 RTA1-N 151192 ============ ===
TEFC 3 159330 B - M3559T 145T 3.6 7/8" 480 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
TEFC 3 111571 B-M3559T-5 145T 3 7/8" 575 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
TEFC 5 111567 K223 F184T 20.2 1-1/8" 240 1 CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
TEFC 5 155048 E241 184T 16 1-1/8" 208 3 CL02A310T-1 151277 14.50 18.00 RTA1-S 151196 ============ ===
TEFC 5 155048 E241 184T 12 1-1/8" 240 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
TEFC 5 155048 E241 184T 6 1-1/8" 480 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
TEFC 5 158170 E273 184T 4.8 1-1/8" 575 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
TEFC 7.5 105842 K305 F215T 34 1-3/8" 240 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
TEFC 7.5 158171 E356 213T 24 1-3/8" 208 3 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
TEFC 7.5 158171 E356 213T 19 1-3/8" 240 3 CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
TEFC 7.5 158171 E356 213T 9.5 1-3/8" 480 3 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 ============ ===
TEFC 7.5 158172 E364 213T 7.6 1-3/8" 575 3 CL00A310T-1 151275 5.50 8.50 RTA1-N 151192 ============ ===
TEFC 10 105846 K313 215T 39 1-3/8" 240 1 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
TEFC 10 158173 E357 215T 30 1-3/8" 208 3 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
TEFC 10 158173 E357 215T 26 1-3/8" 240 3 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
TEFC 10 158173 E357 215T 13 1-3/8" 480 3 CL02A310T-1 151277 10.00 16.00 RTA1-P 151194 ============ ===
TEFC 10 158174 E365 215T 9.6 1-3/8" 575 3 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 ============ ===
Service Power
Type HP P/N Model No. Frame fla Factor Factor Mfr No. P/N min max GE # P/N Mfr No. P/N
OPEN 10 105857 E303 F215T 31.0 1-3/8" 208 3 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
OPEN 10 105858 E301 215T 26.0 1-3/8" 240 3 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
OPEN 10 105858 E301 215T 13.0 1-3/8" 480 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 10 158163 E325 S215T 10.4 1-3/8" 575 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
OPEN 15 142287 B-FM2513T-8 254T 43.1 1-5/8" 208 3 CL06A311M-1 203687 42.00 55.00 RTA2-G 151202 ============ ===
OPEN 15 142288 BALD-FM2513T 254T 39.0 1-5/8" 240 3 CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
OPEN 15 142288 BALD-FM2513T 254T 19.5 1-5/8" 480 3 CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
OPEN 15 142289 B-EFM2513T-5 254T 16.0 1-5/8" 575 3 CL02A310T-1 151277 14.50 18.00 RTA1-S 151196 ============ ===
OPEN 20 142295 B-FM2515T-8 256T 58.7 1-5/8" 208 3 1.15 80 88.50% CL07A311M-1 203793 54.00 65.00 RTA2-H 151203 ============ ===
OPEN 20 142296 BAL-FM2515T 256T 53.0 1-5/8" 240 3 1.15 81 88.50% CL07A311M-1 203793 42.00 55.00 RTA2-G 151202 ============ ===
OPEN 20 142296 BAL-FM2515T 256T 26.5 1-5/8" 480 3 1.15 81 88.50% CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
OPEN 20 142297 B-FM2515T-5 256T 21.2 1-5/8" 575 3 1.15 80 88.50% CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
TEFC 1/4 105566 STK904 M48 3.6 1/2" 120 1 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
TEFC 1/4 16074 108152 J56 2.2 5/8" 208 1 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/4 16074 108152 J56 1.9 5/8" 240 1 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/4 16075 125439 B56 1.6 5/8" 208 3 CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 42AF35AJ-24V 119625
TEFC 1/4 16075 125439 B56 1.4 5/8" 240 3 CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 42AF35AJ-24V 119625
TEFC 1/4 16075 125439 B56 0.7 5/8" 480 3 CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 42AF35AJ-24V 119625
TEFC 1/3 115861 STK906 N48 4.6 1/2" 120 1 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 1/3 159501 C151 N48 2.3 1/2" 208 1 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/3 159501 C151 N48 2.4 1/2" 240 1 CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/3 105567 H261 L48 1.2 1/2" 208 3 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
TEFC 1/3 105567 H261 L48 1.2 1/2" 240 3 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
TEFC 1/3 105567 H261 L48 0.6 1/2" 480 3 CL00A310T-1 151275 0.40 0.65 RTA1-D 151184 ============ ===
TEFC 1/2 159184 C613 J56 7.2 5/8" 120 1 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 42AF35AJ-24V 119625
TEFC 1/2 159184 C613 J56 3.5 5/8" 208 1 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
TEFC 1/2 159184 C613 J56 3.6 5/8" 240 1 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 42AF35AJ-24V 119625
TEFC 1/2 16077 H274 H56 2.3 5/8" 208 3 1 59.5 74.80% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/2 16077 H274 H56 2.0 5/8" 240 3 1 59.5 74.80% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 1/2 16077 H274 H56 1.0 5/8" 480 3 1 59.5 74.80% CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 42AF35AJ-24V 119625
TEFC 1/2 105568 H276 J56 0.7 5/8" 575 3 1.15 76.4 77% CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
TEFC 3/4 115860 F353 F56 11.0 5/8" 120 1 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 42AF35AJ-24V 119625
TEFC 3/4 115860 F353 F56 5.4 5/8" 208 1 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 3/4 159184 F353 F56 5.5 5/8" 240 1 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 42AF35AJ-24V 119625
TEFC 3/4 20371 H580 KA56 2.0 5/8" 208 3 1 73.5 81.10% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 3/4 20371 H580 KA56 2.2 5/8" 240 3 1 73.5 81.10% CL00A310T-1 151275 1.80 2.70 RTA1-J 151189 42AF35AJ-24V 119625
TEFC 3/4 20371 H580 KA56 1.1 5/8" 480 3 1 73.5 81.10% CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 42AF35AJ-24V 119625
TEFC 3/4 105569 H461 L56 0.8 5/8" 575 3 1.15 78.3 82% CL00A310T-1 151275 0.65 1.10 RTA1-F 151186 ============ ===
CODE 47 - Starter Starter OverloadVolt
CODE 45 -Motorph Efficiency %
CODE 46 - ContactorShaft
Form P-DV, Page 8
CODE 48 -
Replacement
Holding Coils
for IEC Starters
Two-Speed
Motors and
Starters
Blower Motors, Contactor, and Starters (cont'd)Service Power
Type HP P/N Model No. Frame fla Factor Factor Mfr No. P/N min max GE # P/N Mfr No. P/N
TEFC 15 142443 BAL-FM2333T 254T 38 1-5/8" 240 3 1.15 82 90.20% CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
TEFC 15 142443 BAL-FM2333T 254T 19 1-5/8" 480 3 1.15 82 90.20% CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
TEFC 15 142444 B-FM2333-5 254T 15 1-5/8" 575 3 1.15 82 90.20% CL02A310T-1 151277 10.00 16.00 RTA1-P 151194 ============ ===
TEFC 20 142301 BAL-FM2334T 256T 52 1-5/8" 240 3 1.15 81 89.50% CL07A311M-1 203793 42.00 55.00 RTA2-G 151202 ============ ===
TEFC 20 142301 BAL-FM2334T 256T 26 1-5/8" 480 3 1.15 81 89.50% CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
TEFC 20 142302 B-FM2334T-5 256T 20.6 1-5/8" 575 3 1.15 81 89.50% CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
EE 1 105659 E103 N143T 3.1 7/8" 208 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 1 159328 E1015 143T 2.7 7/8" 240 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 1 159328 E1015 143T 1.4 7/8" 480 3 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
EE 1 158175 E1006 N143T 1.1 7/8" 575 3 CL00A310T-1 151275 1.00 1.50 RTA1-G 151187 ============ ===
EE 1 1/2 105662 E104 P145T 4.5 7/8" 208 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
EE 1 1/2 159329 E1016 145T 3.9 7/8" 240 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 1 1/2 159329 E1016 145T 2.0 7/8" 480 3 CL00A310T-1 151275 1.90 2.70 RTA1-J 151189 ============ ===
EE 1 1/2 158162 E1007 R145T 1.6 7/8" 575 3 CL00A310T-1 151275 1.30 1.90 RTA1-H 151188 ============ ===
EE 2 105664 E105 P145T 6.0 7/8" 208 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
EE 2 159027 E1017 145T 5.8 7/8" 240 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
EE 2 159027 E1017 145T 2.9 7/8" 480 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 2 158176 E1008 P145T 2.1 7/8" 575 3 CL00A310T-1 151275 1.90 2.70 RTA1-J 151189 ============ ===
EE 3 159186 B-35L405S489G3 145T 8.3 7/8" 208 3 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 ============ ===
EE 3 159028 B-EM3158T 145T 7.4 7/8" 240 3 CL00A310T-1 151275 5.50 8.50 RTA1-N 151192 ============ ===
EE 3 159028 B-EM3158T 145T 3.7 7/8" 480 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 3 159030 B-35L405S709G1 145T 3.0 7/8" 575 3 CL00A310T-1 151275 2.50 4.10 RTA1-K 151190 ============ ===
EE 5 159029 E204 H182T 13.9 1-1/8" 208 3 CL02A310T-1 151277 10.00 16.00 RTA1-P 151194 ============ ===
EE 5 159029 E204 H182T 11.6 1-1/8" 240 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
EE 5 159029 E204 H182T 5.8 1-1/8" 480 3 CL00A310T-1 151275 5.50 8.50 RTA1-M 151192 ============ ===
EE 5 111602 BAL-M3613T-5 184T 4.8 1-1/8" 575 3 CL00A310T-1 151275 4.00 6.30 RTA1-L 151191 ============ ===
EE 7 1/2 159331 E316 D213T 22.3 1-3/8" 208 3 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
EE 7 1/2 159332 E317 D213T 19.4 1-3/8" 240 3 CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
EE 7 1/2 159332 E317 D213T 9.7 1-3/8" 480 3 CL00A310T-1 151275 8.00 12.00 RTA1-N 151193 ============ ===
EE 7 1/2 158164 E324 S213T 7.8 1-3/8" 575 3 CL00A310T-1 151275 5.50 8.50 RTA1-N 151192 ============ ===
EE 10 159333 E318 H215T 27.8 1-3/8" 208 3 CL04A310M-1 151279 25.00 32.00 RTA1-V 151199 ============ ===
EE 10 159334 E397 H215T 24.2 1-3/8" 240 3 CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
EE 10 159334 E397 H215T 12.1 1-3/8" 480 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
EE 10 158163 E325 S215T 10.4 1-3/8" 575 3 CL01A310T-1 151276 10.00 16.00 RTA1-P 151194 ============ ===
EE 15 142440 B-EFM2513T-8 254T 41.5 1-5/8" 208 3 1.15 84 92.40% CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
EE 15 142441 B-EFM2513T 254T 36.0 1-5/8" 240 3 1.15 84 92.40% CL06A311M-1 203687 30.00 43.00 RTA2-E 151206 ============ ===
EE 15 142441 B-EFM2513T 254T 18.0 1-5/8" 480 3 1.15 84 92.40% CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
EE 15 142289 B-EFM2513T-5 254T 16 1-5/8" 575 3 1.15 84 92.40% CL02A310T-1 151277 10.00 16.00 RTA1-P 151194 ============ ===
EE 20 159187 C-E452-F2 S256T 57.0 1-5/8" 208 3 1.15 84 93.60% CL07A311M-1 203793 54.00 65.00 RTA2-H 151203 ============ ===
EE 20 142299 B-EFM2515T 256T 48.0 1-5/8" 240 3 1.15 84 93.00% CL07A311M-1 203793 42.00 55.00 RTA2-G 151202 ============ ===
EE 20 142299 B-EFM2515T 256T 24.0 1-5/8" 480 3 1.15 84 93.00% CL04A310M-1 151279 21.00 26.00 RTA1-U 151198 ============ ===
EE 20 142300 B-EFM2515T-5 256T 19.2 1-5/8" 575 3 1.15 84 93.00% CL25A310T-1 151278 17.50 22.00 RTA1-T 151197 ============ ===
Efficiency %CODE 47 - Starter Starter Overload CODE 46 - ContactorCODE 45 - Motor
Shaft Volt ph
Motor Shaft Mfr Reznor Starter Pkg Reznor
Frame Dia High Speed Low Speed No. P/N V PH Mfr No. P/N
1-.44 M145T 7/8 MAGN 3.8 2.4 M124 105641 208 3 2SP-S17-C-I-H-O 114971
1-.44 M145T 7/8 MAGN 3.4 2.2 M124 105641 240 3 2SP-S17-C-I-H-O 114971
1-.44 M145T 7/8 MAGN 1.7 1.1 M109 105642 480 3 2SP-S17-E-G-F-O 114972
1.5-.68 N145T 7/8 MAGN 5.4 3.1 M125 105643 208 3 2SP-S17-C-K-I-O 114973
1.5-.68 N145T 7/8 MAGN 4.9 2.8 M125 105643 240 3 2SP-S17-C-K-I-O 114973
1.5-.68 N145T 7/8 MAGN 2.4 1.4 M104 105644 480 3 2SP-S17-E-H-G-O 114974
2-.88 S182T 1 1/8 MAGN 6.5 4.2 M220 105645 208 3 2SP-S17-C-L-K-O 114975
2-.88 S182T 1 1/8 MAGN 5.9 3.8 M220 105645 240 3 2SP-S17-C-L-I-O 114976
2-.88 S182T 1 1/8 MAGN 3.4 2.1 M207 105646 480 3 2SP-S17-E-I-H-O 114977
3-1.3 S184T 1 1/8 MAGN 9.3 5.3 M221 105647 208 3 2SP-S17-C-M-K-O 114978
3-1.3 S184T 1 1/8 MAGN 8.4 4.8 M221 105647 240 3 2SP-S17-C-M-K-O 114978
3-1.3 S184T 1 1/8 MAGN 4.6 2.6 M208 105648 480 3 2SP-S17-E-K-H-O 114979
5-2.2 S215T 1 3/8 MAGN 17.2 11.3 M320 105870 208 3 2SP-S17-C-O-M-O 114980
5-2.2 S215T 1 3/8 MAGN 15.5 10.2 M320 105870 240 3 2SP-S17-C-O-M-O 114980
5-2.2 S215T 1 3/8 MAGN 7.1 4.8 M305 105871 480 3 2SP-S17-E-L-K-O 114981
7.5-3.3 Y215T 1 3/8 MAGN 21.6 13.6 M317 105872 208 3 2SP-S27-C-O-N-O 114982
7.5-3.3 Y215T 1 3/8 MAGN 19.5 12.3 M317 105872 240 3 2SP-S27-C-O-N-O 114982
7.5-3.3 D215T 1 3/8 MAGN 10 6 M315 105873 480 3 2SP-S17-E-M-L-O 114983
10-4.4 S256T 1 5/8 MAGN 31 19.4 M421 105874 208 3 2SP-S27-C-P-O-O 114984
10-4.4 S256T 1 5/8 MAGN 28 17.5 M421 105874 240 3 2SP-S27-C-P-O-O 114984
10-4.4 S256T 1 5/8 MAGN 13.5 7.5 M413 105875 480 3 2SP-S17-E-N-L-O 114985
N.O. Auxiliary Contacts: AEG Model HS17.10, 10A, 600V, P/N 115951; N.C. Auxiliary Contacts: AEG Model HS17.01, 10A, 600V, P/N 115952
2-Speed Motors and Motor Starters
CODE 51, 2-Spd Motor Starter
OverloadHP Mfr
CODE 50, 2-Speed Blower Motor
Voltage GE #Reznor
P/N
For Use with Contactors
Beginning with GE#Voltage GE #
Reznor
P/N
For Use with Contactors
Beginning with GE#Voltage GE #
Reznor
P/N
For Use with Contactors
Beginning with GE#
24 LB1A-C 151280 24 LB3A-C 151286 208 LB4A-L 151292
120 LB1A-J 151281 120 LB3A-J 151287 230 LB4A-S 151293
208 LB1A-L 151282 208 LB3A-L 151288 460 LB4A-U 151294
230 LB1A-S 151283 230 LB3A-S 151289
460 LB1A-U 151284 460 LB3A-U 151290
575 LB1A-Y 151285 575 LB3A-Y 151291
CL00; CL01; CL02; CL25 CL04; CL45
CL06; CL07; CL08;
CL09
Form P-DV, Page 9
CODE 65 -P/N 24857, Maxitrol#T115, OverridingThermostat, Option AG33
CODE 64 - Temperature Selectors (see chart for option application)
P/N 86988, TD114 U.S. Models, Range 55-90°F
P/N 101165, TD114, Canadian Models, Range 50-75°F;
P/N 87107, TD114A, Range 80-130°F;
P/N 159285, TD114B, Range 120-160°F;
P/N 133230, Maxitrol#TD294E-609-0818, DualTemperature Selector for PaintBooth Application, OptionAG36
CODE 60 -TemperatureSensor
P/N 90324, Maxitrol #TS114;
P/N 87106, Maxitrol #TS114A
(illustrated);
P/N 123944, Maxitrol #TS114B
CODE 61 - MixingTube, P/N 90323
Modulating Gas Controls
P/N 204452, Maxitrol
#TS394-2B-4;
P/N 204453, Maxitrol
#TS194Q (illustrated)
CODE 62 - Amplifier (Amplifiers are not interchangeable and must match the temperature sensor.)P/N 148590,Maxitrol#A1014L(replacesP/N 86976)
P/N 194159, Maxitrol #A1044CL;P/N 157915, Maxitrol #A1044EL(replaces P/N 119616);P/N 86989, Maxitrol #A1044 (onsystems mfgd prior to 2/91)
P/N204454,Maxitrol#ADFM14
CODE 63 - MaxitrolSignal Conditioner,P/N 134170 (forcomputer control)
P/N 204450, Maxitrol #ADFM44
IMPORTANT NOTE: When replacing a temperature sensor on a Maxitrol MV-9 system (Option AG33), check the Model No. on the
sensor.. P/N 119617 or 194160 is used on units manufactured beginning 2/92; P/N 87041 is used on units manufactured prior to 2/92.
Sensors are not interchangeable; the sensor MUST match the amplifier.
P/N 86990,SelectrastatMaxitrol T-244
P/N 204455,
TD DFM14;
P/N 204451,
TD DFM44
CODE DescriptionIn Gas Cntrl
Option
Serial No.
SuffixLocation P/N
Temperature Sensor, Maxitrol Series 14, #TS114 AG30, AG31 MV-7 Discharge 90324
Temperature Sensor, Maxitrol Series 14A, #TS114A AG32 MV-8 Discharge 87106
Temperature Sensor, Maxitrol Series 14B, #TS114B AG35 MV-8 Discharge 123944
Temperature Sensor, Maxitrol Series 44, #TS44E, 120°F max 119617
Temperature Sensor, Maxitrol Series 44, #TS44C, 140°F max 194160
Temperature Sensor, Maxitrol Series 94, #TS194A AG36 MV-B Discharge 133228
Temperature Sensor, Maxitrol Series 14E, #TS394-2B-4 Outside & Return Air 204452
Temperature Sensor, Maxitrol Series 14E, #TS194Q Discharge 204453
61 Mixing Tube, Maxitrol MTI-12 Same as above 90323
Amplifier, Maxitrol Series 14 & 14A, #A1014L AG 30, 31, 32 MV-7, MV-8 148590
Amplifier, Maxitrol Series 44, #A1044EL, 120°F maximum 157915
Amplifier, Maxitrol Series 44, #A1044CL, 140°F maximum 194159
Amplifier, Maxitrol Series 94, A1494 AG36 MV-B 133229
Amplifier, Maxitrol Series 14E, ADFM14 AG47 MV-D 204454
Amplifier, Maxitrol Series 44E-21 & 44ER-21, ADFM44 AG48, AG51 MV-E, MV-F 204450
63 Signal Conditioner, Maxitrol AG37 MV-C 134170
Temperature Selector, Maxitrol Series 14, #TD114 AG30, AG31 MV-7 Remote 86988 (USA); 101165 (Canada)
Temperature Selector, Maxitrol Series 14A, #TD114A AG32 MV-8 Remote 87107
Temperature Selector, Maxitrol Series 14B, #TD114B AG35 MV-8 Remote 159285
Temperature Selector, Maxitrol Series 14E, #TDDFM14 AG47 MV-D Remote 204455
Selectrastat (temperature selector), Maxitrol Series 44, #T-244 AG33 MV-9 Space 86990
Temperature Selector, Maxitrol Series 44E, #TDDFM44 AG48, AG51 MV-E, MV-F Remote 204451
Temperature Selector, Maxitrol Series 94, #TD294E-609-0818 AG36 MV-B Remote 133230, 120°F; 159287, 160°F
65 Overriding Thermostat, Series 14, #T115 AG 30, 31, 32 MV-7, MV-8 Space 24857
Electrical Control
Compartment (See
page 2.)
MV-9
MV-9 Discharge
MV-D, MV-E,
MV-F
All above
60
64
62
AG47, AG48,
AG51
AG33
AG33
P/N 119617, Maxitrol #TS44E;
P/N 194160, Maxitrol #TS44C;
P/N 133228, Maxitrol TS194A
P/N 133229,Maxitrol #A1494
Form P-DV, Page 10
Pilot Manifold
PilotRegulator Pilot Solenoid Valve
Pilot Pressure Tap
Inlet Pressure Tap
ManifoldPressure
Tap
Valve
Regulator
Valve
Gas Train Components - Regulators, Valves, and Pressure Switches
CODE DescriptionPrior to 9/03 in Manifold
Option BMBeginning 9/03 in Manifold Option BM P/N
70 Pilot Regulator, 3/8", Maxitrol 325-3 62, 63, 64, 65, 53, 66, 67, 68 75, 76. 77, 78, 79 (all) 112644
71 Pilot Solenoid Valve, 24V, V8046C1030 -- 75, 76. 77, 78, 79 (all) 204769
72 Pilot Valve, 24V, 3/8", G/C #S3111AF02N6-CF5 62, 63, 64, 65, 53, 66, 67, 68 -- 145733
73 Solenoid Valve, 3/4" NPT, 24V, #K3A651T 63 -- 123604
74 Solenoid Valve, 1" NPT, 24V, #K3A661T 64 -- 146472
75 Solenoid Valve, 1-1/4" NPT, 24V, #K3A671SF 65, 53 -- 123605
76 Solenoid Valve, 1-1/4" NPT, 24V, #L821460C 67 -- 159731
77 Solenoid Valve, 2" NPT, 24V, #L821480 66 -- 159736
78 Solenoid Valve, 2" NPT, 24V, #L821480C 68 -- 159841
79 Solenoid Valve, M/H V4295A-1031 77 with AG 49 or 50; 78 with AG 30-37,
47, 48, 51
203860
80 Dual Combination Control Valve, 1", 24V, #VR8405M 62 75 with AG1; 76 with AG 30-37, 47, 48, 51 159743
81 2-stage Valve, M/H V8944B-1126 75 with AG3 203866
82 Mechanical Modulation Valve, M/H V5115B-2548 77 with AG 49 or 50 203868
83 Modulating Valve, 3/4", Maxitrol M611R 63 -- 123916
81 Modulating Valve, 1", Maxitrol M611R 62, 64 76 or 78 with AG 30-37, 47, 48, 51 87001
85 Regulator, 2" NPT, Maxitrol 212E 66 81 with AG 30-37, 47, 48, 51 91071
86 Regulator, 1-1/4" NPT, Maxitrol #MR12D 65, 53, 67 79 with AG 30-37, 47, 48, 51 89351
87 Regulator, 1" NPT, Maxitrol #RV53W 62 75 with AG 1 or 3; 76 with AG 30-37, 47,
48, 51; 77 with AG 49 or 50
123950
88 Regulator, 1" NPT, Maxitrol #R600S 64 78 with AG 30-37, 47, 48, 51 86964
89 Regulator, 3/4" NPT, Maxitrol #R600S 63 -- 159717
90 Vent Valve - Normally Open - 3/4" NPT, #L8214633 53, 66 -- 159839
91 2" NPT Ball Valve 66, 68 -- 159735
1-1/4" NPT Ball Valve 65, 53, 67 79 with AG 30-37, 47, 48, 51 159729
1" NPT Ball Valve 62, 64 75 with AG 1 or 3; 76 or 78 with AG 30-
37, 47, 48, 51; 77 with AG 49 or 50
159725
3/4" NPT Ball Valve 63 -- 159716
Pilot Ball Valve, 3/8" -- 75, 76. 77, 78, 79 (all) 159720
92 2" Ball Valve Adapter 66, 68 -- 110760
1-1/4" Ball Valve Adapter 65, 53, 67 79 with AG 30-37, 47, 48, 51 110759
1" Ball Valve Adapter 62, 64 75 with AG 1 or 3; 76 or 78 with AG 30-
37, 47, 48, 51; 77 with AG 49 or 50
110758
3/4" Ball Valve Adapter 63 -- 120169
93 3/4" Pressure Tap Coupler 63 -- 115293
1" Pressure Tap Coupler 64 75 with AG 1 or 3; 76 or 78 with AG 30-
37, 47, 48, 51; 77 with AG 49 or 50
122867
94 53, 66, 67, 68 and Options
BP3 and BP4
-- 93849
95 53, 66, 67, 68 and Options
BP2 and BP4
-- 93850
96 Vent Limiter for Gas Pressure Switches with CODES 97 and 98 with CODES 94 and 95 123481
97 -- Options BP3 and BP4 204375
98 -- 78 or 79 with AG 30-37, 47, 48, 51 and
Options BP2 and BP4
204297
99 1" x 1" NPT (Same as Option CZ1) 124258
1-1/2" x 1-1/2" NPT (Same as Option CZ2) 124259
Gas Supply Regulator Kit, 5 psi
Low Gas Pressure Switch, Auto Reset, Range 1-6" w.c,
#RLGP-A 803112701
High Gas Pressure Switch, Manual Reset, Antunes
#HGP-A 803112601
Low Gas Pressure Switch, Auto Reset, Range 1-6" w.c,
#C097A1053 (Option BP3 and in BP4)
High Gas Pressure Switch, Manual Reset, #C097A1028
(Option BP2 and in BP4)
Form P-DV, Page 11
GasControlRegulators
CODE 85 -P/N 89351,1-1/4" NPT,MaxitrolMR212D
CODE 86 -P/N 91071,2"NPT,MaxitrolMR212E
CODE 70 - PilotRegulator, P/N 112644,Maxitrol 325-3,maximum inlet 5 psi;outlet 3.0" w.c.
CODE 72 - PilotValve, P/N 145733,24V, G/C#S311AF02N6-CF5
CODE 80 - Single-Stage Control Valve, 1" Naturalor Propane, 24V, P/N 159743, M/H #VR8404M5569
CODE 83 -3/4" NPT,MaxitrolM611R,P/N 123916
CODE 84 -1" NPT,MaxitrolM611R, P/N87001
CODE 73 - Solenoid Valve, 3/4" NPT, 24V,#K3A651T, P/N 123604 (illustrated)
CODE 74 - Solenoid Valve, 1" NPT, 24V,K3A661T, P/N 146472
CODE 75 - Solenoid Valve,1-1/4" NPT, 24V, K3A671SF, P/N 123605
CODE 71 -Solenoid Valve,24V,#V8046C1030,P/N 204769
Used with P/N 126170,Discharge Air Controller(ductstat) in Option AG1
CODE 81 - Two-Stage Control Valve, 1", 24V,Natural Gas, P/N 203866, M/H #VR8944B1126
CODE 82 - P/N 203868,Mechanical Modulation Valve,M/H V5115B-2548, in GasControl Options AG49 and AG50
P/N 93849 (Range1-6" w.c.);Automatic Reset,Settings - 50% ofminimum inlet gaspressure as statedon the unit ratingplate
P/N 93850,Manual Reset,Settings - 125%of normalmanifold gaspressure asstated on theunit rating plate
CODE 90 -Vent Valve,P/N 159839,3/4",#L8214633,24V
Regulator, Maxitrol #R600S
CODE 88 - 1" NPT,P/N 86964
CODE 89 - 3/4" NPT,P/N 159717
CODE 94 - Low Gas Pressure Switch(Option BP3)
CODE 96 - Vent Limiterfor Pressure Switches,P/N 123481
CODE 95 - High Gas Pressure Switch(Option BP2)
CODE 87 -Regulator,1" NPT,P/N 123950,Maxitrol#RV53W
Gas Pressure Switches used before 9/03
Gas Pressure Switches used beginning 9/03
CODE 97 - LowGas PressureSwitch(automatic),#C6097A1053,P/N 204375(Option BP3)
CODE 98 - HighGas PressureSwitch (manualreset),#C6097B1028,P/N 204297(Option BP2)
CODE 99 - Gas Regulator Kit, outletpressure range 1-12" (maximum 5 psi)
P/N 124258 (Sameas Option CZ1), Kitincludes Maxitrol1"x1" NPTregulator
P/N 124259 (Sameas Option CZ2), Kitincludes Maxitrol1-1/2"x1-1/2" NPTregulator
Used with P/N 41700,2-Stage Ductstat inOption AG3
CODE 76 - Solenoid Valve, 1-1/4"NPT, 24V, #L821460C, P/N 159731
CODE 77 - Solenoid Valve 2", 24V,#LC21480, P/N 159736
CODE 78 - Solenoid Valve 2", 24V,#LC21480C, P/N 159841
CODE 79 - SolenoidValve, P/N 203860,M/H#V4295A-1031
Form P-DV, Page 12
Ignition System - Hot Surface Ignition
CODE 100 -P/N 157953, Hot Surface
Ignition Module, RAM#H4MC24-01
Pilot andIgnitor
FlameSensor
CODE Description P/N
100 Hot Surface Ignition Module, RAM #H4MC24-01 157953
101 Pilot Assembly for Hot Surface Ignition 120048
including:
Code
101A Pilot 122840
101B Flame Sensor, J/C #Y75MK-1D 134706
101C Screw, #8-1/2" long 38529
101D Pilot bushing 121730
101E Hex head cap screw,
#10-32 x 3/8" long 90167
1014F Hot Surface Ignitor,
Norton #401E 121865
Burners (for units manufactured beginning 9/03)
Bu
rner
Mixing Plates
Ignitor
Gas
Su
pp
ly
Pilot Assembly
Burner End Plate
Beginning 9/03 Model DV uses Midco HMA-700
Series Burners. The Burner P/N listed below includes
the burner, the mixing plates, and the end plate.
Replacement Burners for units manufactured prior to 9/03CODE 104 - Replacement Burner Assemblies (includes burner, end plates and mixing plates)
First Burner Section in the Burner Assy
CODE 104B,End Plate
Length & Configuration MBH P/N
6" Burner - Linear 250 203312
12" Burner - Linear 500 203313
18" Burner - Linear 750 203314
24" Burner - Linear 1,000 203315
30" Burner - Linear 1,250 203316
36" Burner - "H" 1,500 205494
42" Burner - "H" 1,750 205495
48" Burner - "H" 2,000 205496
54" Burner - "H" 2,250 205497
60" Burner - "H" 2,500 205498
66" Burner - "H" 2,750 205499
72" Burner - "H" 3,000 205500
CODE 103 - Model DV BURNER
CODE 104A,Mixing Plate
Burner
MBH Length Configuration P/N
250 6" Linear 123405
500 12" Linear 123665
750 18" Linear 123684
1000 24" Linear 123696
1250 30" Linear 123700
1500 36" H 158767
1750 42" H 158766
2000 48" H 158765
2250 54" H 158764
2500 60" H 158763
2750 66" U 158762
3000 72" H 158761
Burner End Plateshowing HotSurface Ignitor
Code 124F,Ignitor (see
page 10)
Code 124B,Flame Sensor(see page 10)
Code 120B,Burner End
Plate
Burner Components - all sizesof burners and heaters
CODE Description P/N
104A Burner Mixing Plate only, 6" straight section replacement plate. Refer to
Operation/Maintenance/Service Form, RZ-NA O-DV/RDF/ADF, Burner
Cleaning, for instructions on how to access the burner for servicing.
116104, Maxon P/N 20580, (qty
of 6" sections depends on length)
104B Burner End Plate (2) 95473
Form P-DV, Page 13
Damper Motor and Linkage Components by Damper Arrangement Option
P/N 159878,DamperMotor,J/C #M9108-AGA-2
P/N 159877,DamperMotor,J/C#M9216-JCG-2
P/N 159879,DamperMotor,J/C#M9116-AGC-2
P/N 159892,DamperMotor,J/C #M9216-BCG-2
CODE 121 - Damper Motors
Code 110 -DischargeDamperAssembly(fieldmounted)
Code 113 -2-PositionInlet AirDamperAssembly,OptionAR35
(fieldmountedon indoorbaseOptionAVA1)
Code 116,Ball Joint,P/N 12636
Code 117,CrankArm,P/N 12635
CODE 122 - NullPressure Switch,P/N 88052 (remotedamper motorcontrol in AirControl OptionsAR 20 and 23)
CODE 38 (same as page 5)- Potentiometer, P/N 16011(remote damper motorcontrol in Options AR 19and 22)
CODE 123,PhotohelicPressure Switch,P/N 158893(damper motorcontrol in OptionsAR36 and AR37)
Dampers
Dampers and Controls
CODE Description In Option 109 112 115 118 122 125
110 Discharge Damper Assy AR 19, 20, 33, 36; AQ 7 (1)160400 (1)160401 (1)160402 (1)160403 (1)160404 (1)160405
111 Bypass Damper Assy AR 19, 20, 22, 23, 33, 34, 36, 37 -- -- (2)160412 (2)160412 (2)160415 (2)160415
(not illustrated) AR 32 -- -- (2)159894 (2)159894 (2)159895 (2)159895
112 Return Air Damper Assy (not illustrated) AR 22, 23, 32, 34, 37 -- -- (1)160413 (1)160414 (1)160425 (1)160426
113 Inlet Damper Assembly AR 35 (1)161419 (1)161419 (1)161421 (1)161421 (1)161423 (1)161423
CODE Description In Option P/N
114 Bypass Damper Bearing Collar Assy (not illustrated) AR 19, 20, 22, 23, 32, 33, 34, 36, 37 160408
115 Bypass Damper Linkage Plate Shaft 1/2" x 4" AR 19, 20, 22, 23, 32, 33, 34, 36, 37 175103
Assembly (not illustrated) Shaft 1/2" x 7-1/2" AR 19, 20, 22, 23, 32, 33, 34, 36, 37 175250
116 Ball Joint #27518 AR 19, 20, 22, 23, 32, 33, 34, 36. 37 12636
117 Crank Arm for Return Air Damper #26026N AR 32 12635
118 Damper Rod 1/4" x 28" long AR 19, 20, 22, 23, 32, 34, 36, 37 160410
(not illustrated) 1/4" x 16" long AR 32 11560
119 Return Air Damper Shaft (not illustrated) 1/2" x 10" AR 22, 23, 34, 37 161440
120 Extension Shaft (not illustrated) AR 32 123642
121 Bypass Damper Motor J/C M9108-AGA-2 AR 19, 20, 22, 23, 33, 34, 36, 37 159878
J/C M9216-BGC-2 AR 32 159892
Discharge Damper Motor J/C M9216-JGC-2 AR 19, 20 159877
J/C M9216-HGC-2 AR 33 159880
J/C M9116-AGC-2 AR 36 159879
J/C #M9216-BGC-2 AQ 7 159892
Return Air Damper Motor J/C M9216-JGC-2 AR 22 159877
J/C M9216-HGC-2 AR 34 159880
J/C M9116-AGC-2 AR 37 159879
Inlet Air Damper Motor J/C #M9216-BGC-2 AR35 159892
Form P-DV, Page 14
Blowers and Blower Motor Mounting
CODE Description 109 112 115 118 122 125
130 Blower including shaft (1)158707 (1)158702 (1)158703 (1)158704 (1)158705 (1)158706
and bearings A9-7A, A12-9A, A15-15A, A18-18A, A22-22H, A25-25H
Lau 027142-01, Lau 027142-05, Lau 027142-08, Lau 027142-15, Lau 050365-03, Lau 050366-03,
Class 1 Class 1 Class 1 Class 2 Class 1 Class 1
131 Conduit for Motor Wire (1)158752 (1)158752 (1)158753 (1)158753 (1)158754 (1)158754
Harness, 1" 9 feet 9 feet 12 feet 12 feet 15 feet 15 feet
132 90° , 1" Fitting for Motor Wire (2)158741 (2)158741 (2)158741 (2)158741 (2)158741 (2)158741
Harness, Liquidtight LT9100P
133 Motor Mount Angle, All HP -- -- -- (2)158399 (2)158399 (2)158399
134 Motor Mount Brace, All HP -- -- -- (1)159453 -- --
135 Motor Support Rail Assy, -- -- -- (2)159548 (2)159548 (2)159548
Horizontal Discharge, 7.5 - 20 HP 7.5 - 20 HP 7.5 - 20 HP
without vibration isolation
136 Motor Support Rail Assy, -- -- -- (2)159527 (2)159527 (2)159527
Horizontal Discharge, 7.5 - 20 HP 7.5 - 20 HP 7.5 - 20 HP
with vibration isolation
137 Motor Mounting Plate Assy, (1)159531 (1)159531 (1)159532 (1)162943 (1)162944 (1)162945
Horizontal Discharge 1/4 - 2 HP 1/2 - 5 HP 1.5 - 7.5 HP 2 - 5 HP 1.5 - 5 HP 3 - 5 HP
137A Tilt Base Right (1)158982 (1)158982 (1)158981 (1)163594 (1)163595 (1)158981
137B Tilt Base Left (1)158980 (1)158980 (1)158983 (1)163596 (1)163597 (1)158983
137C Motor Mounting Plate (1)159475 (1)159475 (1)159475 (1)159475 (1)159475 (1)159475
137D 5/16-18 x 3/4" lg Screw (6)16247 (6)16247 (6)16247 (6)16247 (6)16247 (6)16247
137E 5-16-18 x 1-1/2" lg Screw (2)16248 (2)16248 (2)16248 (2)16248 (2)16248 (2)16248
137F 5/16-18 Hex Nut (Kep) (12)6554 (12)6554 (12)6554 (12)6554 (12)6554 (12)6554
137G 5/16-18 Flat Washer (12)1087 (12)1087 (12)1087 (12)1087 (12)1087 (12)1087
137H 5/16-18 Rod Bolt (2)12489 (2)12489 (2)12489 (2)12489 (2)12489 (2)12489
138 Motor Mounting Plate Assy, (1)159874 -- (1)159875 -- -- --
Up Discharge 1/4 - 2 HP 1.5 - 7.5 HP
138A Tilt Base Right (1)159493 -- (1)159492 -- -- --
138B Tilt Base Left (1)159491 -- (1)159494 -- -- --
138C Motor Mounting Plate (1)159475 -- (1)159475 -- -- --
138D 5/16-18 x 3/4" lg Screw (6)16247 -- (6)16247 -- -- --
138E 5-16-18 x 1-1/2" lg Screw (2)16248 -- (2)16248 -- -- --
138F 5/16-18 Hex Nut (Kep) (12)6554 -- (12)6554 -- -- --
138G 5/16-18 Flat Washer (12)1087 -- (12)1087 -- -- --
138H 5/16-18 Rod Bolt (2)12489 -- (2)12489 -- -- --
139 Motor Mount, Up Discharge -- -- -- -- (2)159881 --
1.5 - 20 HP
140 Vibration Isolation Stud, K42, (4)159533 (4)159533 (4)159533 (4)159533 (4)159533 (4)159533
Hrzntl & Up Dschrg, All HP
141 Motor Mounting Plate Assy, -- -- -- (1)159530 (1)159530 (1)159530
Horizontal Discharge 7.5 - 20 HP 7.5 - 20 HP 7.5 - 20 HP
142 Motor Adjustment Bolt, -- -- -- (1)158196 (1)158196 (1)158196
1/2"-13 x 9" long 7.5 - 20 HP 7.5 - 20 HP 7.5 - 20 HP
143 Nut for CODE 142 -- -- -- (1)45550 (1)45550 (1)45550
Form P-DV, Page 15
CODE 145 - Drive ComponentsKey and Notes to Drive Charts on pages 15 - 20.
Drive NOTES (Apply to all Drive Tables):
• Service factor on all drives 1/4 to 10 HP is 1.15.
• Service factor on all drives 15 and 20 HP is 1.25.
• All drive assemblies are adjustable. The drive option is listed in the Drive Table; identify RPM range
in the chart below.
• Only drives for standard horizontal discharge are listed. For optional vertical discharge drive
components, contact the factory.
Drive Tables for Model DV
AK1 115V-1Ph-60 Hertz
AK2 208V-1Ph-60 Hertz
AK3 230V-1Ph-60 Hertz
AK5 200/208V-3Ph-60 Hertz
AK6 230V-3Ph-60 Hertz
AK7 460V-3Ph-60 Hertz
AK8 575V-3Ph-60 Hertz
Unit Supply Voltage
MOTOR DRIVE AM Option V - AK Option MOTOR PULLEY BLOWER PULLEY BUSHING
HP AL P/N Model Bore P/N Model Bore P/N Model Qty P/N Model
OPEN Driproof Motors
2 8 18, 19, 20, 21, 22, 23, 24 1, 2, 3, 5, 6, 7, 8 H 106758 1VL44 7/8 105477 AK46 3/4 ----- ----- 1 50500 A41
1/2, 3/4 4, 5 11, 12, 13, 14, 15, 16 1, 2, 3, 5, 6, 7 H 7962 1VL40 5/8 105480 AK54 3/4 ----- ----- 1 50500 A41
1, 1-1/2 6, 7 17, 18, 19, 20, 21, 22, 23, 24 H 105476 1VL44 5/8 105477 AK46 3/4 ----- ----- 1 50500 A41
1, 1-1/2 6, 7 17, 18, 19, 20, 21, 22, 23, 24 8 H 106748 1VL40 7/8 105478 AK41 3/4 ----- ----- 1 105493 A39
1/4, 1/3 2, 3 5, 6, 7, 8 1, 2, 3, 5, 6, 7 H 4074 1VL34 1/2 19108 AK64 3/4 ----- ----- 1 50500 A41
9, 10, 11, 12, 13, 14, 15 H 4074 1VL34 1/2 105477 AK46 3/4 ----- ----- 1 16018 A38
Totally Enclosed Motors (TEFC)
2 25 18, 19, 20, 21, 22, 23, 24 5, 6, 7, 8 H 106758 1VL44 7/8 105477 AK46 3/4 ----- ----- 1 50500 A41
1, 3 H 110151 1VP44 1-1/8 105477 AK46 3/4 ----- ----- 1 50470 A43
11, 12, 13, 14, 15, 16 1, 2, 3, 5, 6, 7, 8 H 7962 1VL40 5/8 105480 AK54 3/4 ----- ----- 1 50500 A41
17, 18, 19, 20, 21, 22, 23, 24 H 105476 1VL44 5/8 105477 AK46 3/4 ----- ----- 1 50500 A41
1-1/2 24 17, 18, 19, 20, 21, 22, 23, 24 8 H 106748 1VL40 7/8 105478 AK41 3/4 ----- ----- 1 105493 A39
1, 2, 3, 5, 6, 7 H 105476 1VL44 5/8 105477 AK46 3/4 ----- ----- 1 50500 A41
1/3 20 5, 6, 7, 8 1, 2, 3, 5, 6, 7 H 4074 1VL34 1/2 19108 AK64 3/4 ----- ----- 1 50500 A41
9, 10, 11, 12, 13, 14, 15 H 4074 1VL34 1/2 105477 AK46 3/4 ----- ----- 1 16018 A38
1/4 19 5, 6, 7, 8 1 H 4074 1VL34 1/2 19108 AK64 3/4 ----- ----- 1 50500 A41
9, 10, 11, 12, 13, 14, 15 H 4074 1VL34 1/2 105477 AK46 3/4 ----- ----- 1 16018 A38
1/4 19 5, 6, 7, 8 2, 3, 5, 6, 7 H 13580 1VL34 5/8 19108 AK64 3/4 ----- ----- 1 101412 A42
9, 10, 11, 12, 13, 14, 15 H 13580 1VL34 5/8 105477 AK46 3/4 ----- ----- 1 105493 A39
Premium Efficiency Motors (EE)
1, 1-1/2, 36, 37, 13, 14, 15, 16, 17 5, 6, 7, 8 H 106758 1VL44 7/8 110807 AK56H ----- 105487 H x 3/4 1 101412 A42
2 38 18, 19, 20, 21, 22, 23, 24 H 106758 1VL44 7/8 105477 AK46 3/4 ----- ----- 1 50500 A41
2 SPEED Motors
1, 1-1/2 13, 14, 15, 16, 17 5, 6, 7 H 106758 1VL44 7/8 110807 AK56H ----- 105487 H x 3/4 1 101412 A42
18, 19, 20, 21, 22, 23, 24 H 106758 1VL44 7/8 105477 AK46 3/4 ----- ----- 1 50500 A41
2 47 18, 19, 20, 21, 22, 23, 24 5, 6, 7 H 110151 1VP44 1 1/8 105477 AK46 3/4 ----- ----- 1 50470 A43
DV-109 DRIVE TABLE
45, 46
BELTS
(See Key above)DISCH
21, 22,
23
1/2, 3/4,
1
Motor Type and HP
AL2 1/4 HP AL19 1/4 HP AL36 1 HP AL45 1 HP
AL3 1/3 HP AL20 1/3 HP AL37 1-1/2 HP AL46 1-1/2 HP
AL4 1/2 HP AL21 1/2 HP AL38 2 HP AL47 2 HP
AL5 3/4 HP AL22 3/4 HP AL39 3 HP AL48 3 HP
AL6 1 HP AL23 1 HP AL40 5 HP AL49 5 HP
AL7 1-1/2 HP AL24 1-1/2 HP AL41 7-1/2 HP AL50 7-1/2 HP
AL8 2 HP AL25 2 HP AL42 10 HP AL51 10 HP
AL9 3 HP AL26 3 HP AL43 15 HP
AL10 5 HP AL27 5 HP AL44 20 HP
AL11 7-1/2 HP AL32 7-1/2 HP
AL12 10 HP AL33 10 HP
AL15 15 HP AL34 15 HP
AL16 20 HP AL35 20 HP
TOTALLY
ENCLOSED (TEFC)
OPEN,
DRIPPROOF
PREMIUM
EFFICIENCY (EE)TWO-SPEED
Opt RPM Opt RPM
AMA2 251-300 AM13 1001-1050
AMA3 301-350 AM14 1051-1100
AMA4 351-400 AM15 1101-1150
AM1 401-450 AM16 1151-1200
AM2 451-500 AM17 1201-1250
AM3 501-550 AM18 1251-1300
AM4 551-600 AM19 1301-1350
AM5 601-650 AM20 1351-1400
AM6 651-700 AM21 1401-1450
AM7 701-750 AM22 1451-1500
AM8 751-800 AM23 1501-1550
AM9 801-850 AM24 1551-1600
AM10 851-900 AM25 1601-1650
Drives
Form P-DV, Page 16
Drives (cont'd)
MOTOR DRIVE AM Option V - AK Opt MOTOR PULLEY BLOWER PULLEY BUSHING
HP AL P/N Model Bore P/N Model Bore P/N Model Qty P/N Model
OPEN Driproof Motors
1/2, 3/4, 3, 4 H
1, 1-1/2 5, 6, 7, 8 H 13580 1VL34 5/8 18797 AK64 1 ----- ----- 1 50475 A49
9, 10, 11, 12, 13, 14, 15, 16 H 13580 1VL34 5/8 105481 AK46 1 ----- ----- 1 50473 A46
1, 1-1/2 6, 7 5, 6, 7, 8 H 110125 1VP34 7/8 18797 AK64 1 ----- ----- 1 50475 A49
9, 10, 11, 12, 13, 14, 15, 16 H 110125 1VP34 7/8 105481 AK46 1 ----- ----- 1 50473 A46
2 8 9, 10, 11, 12, 13, 14 H 106748 1VL40 7/8 115716 AK59 1 ----- ----- 1 50475 A49
15, 16, 17, 18, 19, 20 H 106748 1VL40 7/8 105481 AK46 1 ----- ----- 1 50474 A47
3 9 12, 13, 14, 15, 16, 17 H 7962 1VL40 5/8 111609 AK99 1 ----- ----- 1 16133 A56
18, 19, 20, 21, 22, 23, 24 H 7962 1VL40 5/8 135281 BK85H ----- 92203 H x 1 1 92222 B53
3, 5 9, 10 12, 13, 14, 15, 16 H 37451 1VM50 7/8 152022 BK140 1 ----- ----- 1 92414 B64
17, 18, 19, 20, 21, 22, 23, 24 H 106748 1VL40 7/8 135281 BK85H ----- 92203 H x 1 1 114341 BX53
5 10 15, 16, 17, 18, 19, 20 H 111681 1VP50 1 1/8 125110 BK120H ----- 92203 H x 1 1 7950 B62
21, 22, 23, 24 H 161444 1VP56 1 1/8 125110 BK120H ----- 92203 H x 1 1 5984 B63
Totally Enclosed Motors (TEFC)
1/2, 3/4, 3, 4 H
1 5, 6, 7, 8 H 13580 1VL34 5/8 18797 AK64 1 ----- ----- 1 50475 A49
9, 10, 11, 12, 13, 14, 15, 16 H 13580 1VL34 5/8 105481 AK46 1 ----- ----- 1 50473 A46
1-1/2 24 5, 6, 7, 8 H 13580 1VL34 5/8 18797 AK64 1 ----- ----- 1 50475 A49
9, 10, 11, 12, 13, 14, 15, 16 H 13580 1VL34 5/8 105481 AK46 1 ----- ----- 1 50473 A46
1-1/2 24 5, 6, 7, 8 H 110125 1VP34 7/8 18797 AK64 1 ----- ----- 1 50475 A49
9, 10, 11, 12, 13, 14, 15, 16 H 110125 1VP34 7/8 105481 AK46 1 ----- ----- 1 50473 A46
9, 10, 11 H 111681 1VP50 1 1/8 19111 AK84 1 ----- ----- 1 16134 A57
2 25 12, 13, 14, 15, 16 1, 3 H 111681 1VP50 1 1/8 105483 AK69 1 ----- ----- 1 16131 A54
17, 18, 19, 20 H 111681 1VP50 1 1/8 115716 AK59 1 ----- ----- 1 16130 A53
2 25 9, 10, 11, 12, 13, 14 5, 6, 7, 8 H 106748 1VL40 7/8 115716 AK59 1 ----- ----- 1 50475 A49
15, 16, 17, 18, 19, 20 H 106748 1VL40 7/8 105481 AK46 1 ----- ----- 1 50474 A47
12, 13, 14, 15, 16 H 111681 1VP50 1 1/8 50520 AK134 1 ----- ----- 1 114103 A65
3 26 17, 18, 19, 20 1, 3, 8 H 111681 1VP50 1 1/8 152021 AK114 1 ----- ----- 1 16137 A62
21, 22, 23, 24 H 161444 1VP56 1 1/8 125110 BK120H 1 92203 H x 1 1 5984 B63
3 26 12, 13, 14, 15, 16 H 37451 1VM50 7/8 152022 BK140 1 ----- ----- 1 92414 B64
17, 18, 19, 20, 21, 22, 23, 24 H 106748 1VL40 7/8 135281 BK85H ----- 92203 H x 1 1 114341 BX53
5 27 15, 16, 17, 18, 19, 20 H 111681 1VP50 1 1/8 125110 BK120H ----- 92203 H x 1 1 7950 B62
21, 22, 23, 24 H 161144 1VP56 1 1/8 125110 BK120H ----- 92203 H x 1 1 5984 B63
Premium Efficiency Motors (EE)
5, 6, 7 H 106748 1VL40 7/8 19111 AK84 1 ----- ----- 1 16130 A53
8, 9, 10, 11 H 106748 1VL40 7/8 135279 AK66 1 ----- ----- 1 88558 A50
12, 13, 14, 15, 16, 17 H 106748 1VL40 7/8 135200 AK51 1 ----- ----- 1 65403 A48
3 39 12, 13, 14, 15, 16 H 37451 1VM50 7/8 152022 BK140 1 ----- ----- 1 92414 B64
17, 18, 19, 20, 21, 22, 23, 24 H 106748 1VL40 7/8 135281 BK85H ----- 92203 H x 1 1 114341 BX53
5 40 15, 16, 17, 18, 19, 20 H 111681 1VP50 1 1/8 125110 BK120H ----- 92203 H x 1 1 7950 B62
21, 22, 23, 24 H 161444 1VP56 1 1/8 125110 BK120H ----- 92203 H x 1 1 5984 B63
2 SPEED Motors
5, 6, 7 H 106748 1VL40 7/8 19111 AK84 1 ----- ----- 1 16130 A53
8, 9, 10, 11 H 106748 1VL40 7/8 135279 AK66 1 ----- ----- 1 88558 A50
12, 13, 14, 15, 16, 17 H 106748 1VL40 7/8 135200 AK51 1 ----- ----- 1 65403 A48
6, 7, 8, 9 H 110151 1VP44 1 1/8 19111 AK84 1 ----- ----- 1 16133 A56
10, 11, 12, 13 H 110151 1VP44 1 1/8 135279 AK66 1 ----- ----- 1 16130 A53
14, 15, 16, 17, 18 H 110151 1VP44 1 1/8 105482 AK56 1 ----- ----- 1 65404 A51
19, 20, 21, 22, 23, 24 H 161444 1VP56 1 1/8 115716 AK59 1 ----- ----- 1 16131 A54
5 49 16, 17, 18, 19 H 161448 1VP60 1 3/8 105484 AK71H 1 92203 H x 1 1 50476 A58
20, 21, 22, 23, 24 H 161449 1VP62 1 3/8 135279 AK66 1 ----- ----- 1 50476 A58
(Contact Service Department for components.)
(Contact Service Department for components.)
45,
46
1, 1-1/2
1, 2, 3, 4, 5,
6, 7, 8
1, 2, 3, 4, 5,
6, 7, 8
1, 2, 3, 5, 6,
7
5, 6, 7
47,
48
2, 3
5, 6, 7, 8
4, 5,
6, 7
21,
22,
23
5, 6, 7
5, 6, 7, 8
1, 1-1/2,
2
36,
37,
38
1, 2, 3, 5, 6,
7
DISCHBELTS
(See Key on page 15)
DV-112 DRIVE TABLE
5, 6, 7
5, 6, 7
8
2, 3
5, 6, 7, 8
2, 3
8
3, 5, 6, 7, 8
5, 6, 7, 8
Form P-DV, Page 17
MOTOR DRIVE AM Option V - AK Opt MOTOR PULLEY BLOWER PULLEY BUSHING
HP AL P/N Model Bore P/N Model Bore P/N Model Qty P/N Model
1 1/2 7 5, 6, 7, 8 1, 2, 3, 5, 6, 7 H 13580 1VL34 5/8 123761 AK64H ----- 106260 H x 1-3/16 1 16132 A55
8 H 110125 1VP34 7/8 123761 AK64H ----- 106260 H x 1-3/16 1 16132 A55
2 88, 9, 10, 11
1, 2, 3, 5, 6,
7, 8H 106758 1VL44 7/8 106256 AK74 1 3/16 ----- ----- 1 50476 A58
3 9 7, 8, 9, 10, 11 H 13580 1VL34 5/8 125110 BK120H ----- 106260 H x 1-3/16 1 114258 BX64
12, 13, 14 H 7962 1VL40 5/8 16155 AK114 1 3/16 ----- ----- 1 80836 A64
3, 5 9, 10 7, 8, 9 H 106758 1VL44 7/8 152023 1B5V160 ----- 115251 B x 1-3/16 1 92404 A74
10 ,11, 12, 13 H 110125 1VP34 7/8 114026 BK110H ----- 106260 H x 1-3/16 1 92411 BX62
14, 15, 16, 17 H 106758 1VL44 7/8 152020 AK109H ----- 106260 H x 1-3/16 1 80836 A64
5 10 9, 10, 11 H 161444 1VP56 1 1/8 16160 AK184 1 3/16 ----- ----- 1 92217 A81
12, 13, 14, 15, 16 H 111681 1VP50 1 1/8 16158 AK134 1 3/16 ----- ----- 1 124347 A71
7 1/2 11 12, 13, 14, 15 H 161448 1VP60 1 3/8 162836 BK90H ----- 106260 H x 1-3/16 1 92276 BX65
16, 17, 18, 19, 20 H 161448 1VP60 1 3/8 112026 BK75H ----- 106260 H x 1-3/16 1 92411 BX62
Totally Enclosed Motors (TEFC)
1 1/2 24 5, 6, 7, 8 1, 2, 3, 5, 6, 7 H 13580 1VL34 5/8 123761 AK64H ----- 106260 H x 1-3/16 1 16132 A55
8 H 110125 1VP34 7/8 123761 AK64H ----- 106260 H x 1-3/16 1 16132 A55
2 25 8, 9, 10, 11 5, 6, 7, 8 H 106758 1VL44 7/8 106256 AK74 1 3/16 ----- ----- 1 50476 A58
1, 3 H 110151 1VP44 1 1/8 106256 AK74 1 3/16 ----- ----- 1 50477 A60
7, 8 H 111681 1VP50 1 1/8 16160 AK184 1 3/16 ----- ----- 1 92217 A81
3 26 9, 10, 11 1, 3, 8 H 161444 1VP56 1 1/8 16160 AK184 1 3/16 ----- ----- 1 92217 A81
12, 13, 14, 15, 16 H 111681 1VP50 1 1/8 16158 AK134 1 3/16 ----- ----- 1 124347 A71
7, 8, 9 H 106758 1VL44 7/8 152023 1B5V160 ----- 115251 B x 1-3/16 1 92404 A74
3 26 10 ,11, 12, 13 H 110125 1VP34 7/8 114026 BK110H ----- 106260 H x 1-3/16 1 92411 BX62
14, 15, 16, 17 H 106758 1VL44 7/8 152020 AK109H ----- 106260 H x 1-3/16 1 80836 A64
5 27 9, 10, 11 3, 5, 6, H 161444 1VP56 1 1/8 16160 AK184 1 3/16 ----- ----- 1 92217 A81
12, 13, 14, 15, 16 7, 8 H 111681 1VP50 1 1/8 16158 AK134 1 3/16 ----- ----- 1 124347 A71
7 1/2 32 12, 13, 14, 15 3, 5, 6, 7, 8 H 161448 1VP60 1 3/8 162836 BK90H ----- 106260 H x 1-3/16 1 92276 BX65
16, 17, 18, 19, 20 H 161448 1VP60 1 3/8 112026 BK75H ----- 106260 H x 1-3/16 1 92411 BX62
Premium Efficiency Motors (EE)
37, 38 6, 7 H 106748 1VL40 7/8 111862 AK84 1 3/16 ----- ----- 1 92402 A59
8, 9, 10, 11 H 106758 1VL44 7/8 106256 AK74 1 3/16 ----- ----- 1 50476 A58
7, 8, 9 H 106758 1VL44 7/8 152023 1B5V160 ----- 115251 B x 1-3/16 1 92404 A74
3 39 10 ,11, 12, 13 5, 6, 7, 8 H 110125 1VP34 7/8 114026 BK110H ----- 106260 H x 1-3/16 1 92411 BX62
14, 15, 16, 17 H 106758 1VL44 7/8 152020 AK109H ----- 106260 H x 1-3/16 1 80836 A64
5 40 9, 10, 11 H 161444 1VP56 1 1/8 16160 AK184 1 3/16 ----- ----- 1 92217 A81
12, 13, 14, 15, 16 H 111681 1VP50 1 1/8 16158 AK134 1 3/16 ----- ----- 1 124347 A71
7 1/2 41 12, 13, 14, 15 H 161448 1VP60 1 3/8 162836 BK90H ----- 106260 H x 1-3/16 1 92276 BX65
16, 17, 18, 19, 20 H 161448 1VP60 1 3/8 112026 BK75H ----- 106260 H x 1-3/16 1 92411 BX62
2 SPEED Motors
1 1/2 46 5, 6, 7, 8 5, 6, 7 H 110125 1VP34 7/8 123761 AK64H ----- 106260 H x 1-3/16 1 16132 A55
6, 7, 8, 9 H 110151 1VP44 1 1/8 111862 AK84 1 3/16 ----- ----- 1 16137 A62
2, 3 47, 48 10, 11 5, 6, 7 H 110151 1VP44 1 1/8 106256 AK74 1 3/16 ----- ----- 1 50477 A60
12, 13, 14, 15 H 111681 1VP50 1 1/8 105484 AK71H ----- 106260 H x 1-3/16 1 88560 A61
49, 50 12, 13, 14, 15 5, 6, 7 H 161448 1VP60 1 3/8 162836 BK90H ----- 106260 H x 1-3/16 1 92276 BX65
16, 17, 18, 19, 20 H 161448 1VP60 1 3/8 112026 BK75H ----- 106260 H x 1-3/16 1 92411 BX62
5, 6, 7, 8
DV-115 DRIVE TABLE
DISCHBELTS
(See Key on page 15)
5, 6, 7, 8
OPEN Driproof Motors
5, 7-
1/2
1 1/2,
2
2, 3
5, 6, 7, 8
2, 3, 5, 6, 7, 8
2, 3
5, 6, 7
5, 6, 7, 8
Form P-DV, Page 18
Drives (cont'd)
MOTOR DRIVE AM Opt V - AK Option MOTOR PULLEY BLOWER PULLEY BUSHING
HP AL P/N Model Bore P/N Model P/N Model Qty P/N Model
2 8 5, 6, 7 1, 2, 3, 5, 6, 7, 8 H 106748 1VL40 7/8 162883 AK84H 89659 H x 1 7/16 1 80836 A64
3 9 6, 7, 8, 9 2, 3 H 105476 1VL44 5/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
3, 5 6, 7, 8, 9 5, 6, 7, 8 H 106758 1VL44 7/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
10, 11 H 110125 1VP34 7/8 125110 BK120H 89659 H x 1 7/16 1 92242 BX70
5 10 7, 8, 9 2, 3 H 111681 1VP50 1 1/8 113799 AK184H 89659 H x 1 7/16 1 92219 A86
10, 11 H 110151 1VP44 1 1/8 113800 AK144H 89659 H x 1 7/16 1 80838 A77
8, 9 H 106257 2VP60 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
10, 11 H 110771 2VP65 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
12, 13, 14, 15 H 106257 2VP60 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 21860 B67
16, 17 H 110771 2VP65 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 16145 B68
12, 13, 14 H 148593 2MVP70B84P* 1 5/8 162940 2B5V136 114033 B x 1 7/16 2 92415 B82
15, 16, 17, 18 H 148593 2MVP70B84P* 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92271 B79
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Totally Enclosed Motors (TEFC)
2 25 5, 6 5, 6, 7, 8 H 106748 1VL40 7/8 162883 AK84H 89659 H x 1 7/16 1 80836 A64
1, 3 H 111681 1VP50 1 1/8 125110 BK120H 89659 H x 1 7/16 1 92230 B73
3 26 6, 7, 8, 9 1, 3, 8 H 110151 1VP44 1 1/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
5, 6, 7 H 106758 1VL44 7/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
5 27 6, 7, 8, 9 H 110151 1VP44 1 1/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
10, 11 H 110151 1VP44 1 1/8 113800 AK144H 89659 H x 1 7/16 1 80838 A77
8, 9 H 106257 2VP60 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
10, 11 H 110771 2VP65 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
12, 13, 14, 15 H 106257 2VP60 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 21860 B67
16, 17 H 110771 2VP65 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 16145 B68
12, 13, 14 H 148593 2MVP70B84P* 1 5/8 162940 2B5V136 114033 B x 1 7/16 2 92415 B82
15, 16, 17, 18 H 148593 2MVP70B84P* 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92271 B79
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Premium Efficiency Motors (EE)
2 38 5, 6 5, 6, 7, 8 H 106748 1VL40 7/8 162883 AK84H 89659 H x 1 7/16 1 80836 A64
3 39 6, 7, 8, 9 5, 6, 7, 8 H 106758 1VL44 7/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
5 40 6, 7, 8, 9 H 110151 1VP44 1 1/8 152023 1B5V160 114033 B x 1 7/16 1 92217 A81
10, 11 H 110151 1VP44 1 1/8 113800 AK144H 89659 H x 1 7/16 1 80838 A77
8, 9 H 106257 2VP60 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
10, 11 H 110771 2VP65 1 3/8 113811 2BK120H 89659 H x 1 7/16 2 92230 B73
12, 13, 14, 15 H 106257 2VP60 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 21860 B67
16, 17 H 110771 2VP65 1 3/8 113804 2BK90H 89659 H x 1 7/16 2 16145 B68
12, 13, 14 H 148593 2MVP70B84P* 1 5/8 162940 2B5V136 114033 B x 1 7/16 2 92415 B82
15, 16, 17, 18 H 148593 2MVP70B84P* 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92271 B79
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
2 SPEED Motors
2, 3 5, 6, 7 H 111681 1VP50 1 1/8 113798 AK104H 89659 H x 1 7/16 1 114257 A70
8, 9, 10, 11 H 110151 1VP44 1 1/8 124641 AK74H 89659 H x 1 7/16 1 114103 A65
7, 8 H 163421 1VP65 1 3/8 163422 BK140H 89659 H x 1 7/16 1 92232 B76
9, 10, 11 H 163421 1VP65 1 3/8 125110 BK120H 89659 H x 1 7/16 1 92230 B73
12, 13, 14, 15 H 161448 1VP60 1 3/8 162836 BK90H 89659 H x 1 7/16 1 80841 BX67
16, 17 H 163421 1VP65 1 3/8 162836 BK90H 89659 H x 1 7/16 1 16145 B68
10 51 7, 8, 9 H 110223 2VP60 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92231 B74
10, 11, 12, 13, H 110223 2VP60 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92229 B71
14, 15, 16, 17 H 110221 2VP65 1 5/8 113804 2BK90H 89659 H x 1 7/16 2 92228 B70
5, 7 1/2 49, 50
5, 6, 7
DISCH(See Key on page 15)
OPEN Driproof Motors
5, 6, 7, 8
5, 6, 7
5, 6, 7
47, 48
5, 6, 7, 8
3, 5, 6, 7, 8
6, 7, 8
3, 5, 6, 7, 8
15, 20 43, 445, 6, 7, 8
5, 6, 7, 8
15, 20 34, 35
7 1/2,
10
41, 42
15, 1615, 20
7 1/2,
10
32, 22
DV-118 DRIVE TABLE
7 1/2,
10
9, 10
11, 12
2, 3, 5, 6, 7, 8
BELTS
Form P-DV, Page 19
MOTOR DRIVE AM Opt V - AK Option MOTOR PULLEY BUSHING
HP AL P/N Model Bore P/N Model P/N Model Qty P/N Model
1 1/2 7 A2, A3 1, 2, 3, 5, 6, 7 H 13580 1VL34 5/8 113800 AK144H 89659 H x 1 7/16 1 92266 A79
8 H 110125 1VP34 7/8 113800 AK144H 89659 H x 1 7/16 1 92266 A79
2 8 A3, A4 1, 2, 3, 5, 6, 7, 8 H 106748 1VL40 7/8 114248 AK154H 89659 H x 1 7/16 1 92217 A81
3 9 A3, A4 2, 3 H 13580 1VL34 5/8 163896 1B5V278 114033 B x 1 7/16 1 92314 BX105
1, 2 H 105476 1VL44 5/8 163896 1B5V278 114033 B x 1 7/16 1 163897 A105
A3, A4 5, 6, 7, 8 H 110125 1VP34 7/8 163896 1B5V278 114033 B x 1 7/16 1 92314 BX105
1, 2 H 106758 1VL44 7/8 163896 1B5V278 114033 B x 1 7/16 1 163897 A105
5 10 1, 2 2, 3 H 110151 1VP44 1 1/8 163896 1B5V278 114033 B x 1 7/16 1 163898 BX108
3, 4, 5 H 111681 1VP50 1 1/8 163899 1B5V250 114033 B x 1 7/16 1 124667 A103
1, 2 5, 6, 7, 8 H 106748 1VL40 7/8 163899 1B5V250 114033 B x 1 7/16 1 115932 BX99
3, 4, 5 H 106748 1VL40 7/8 126006 1BV5200 114033 B x 1 7/16 1 92315 BX90
2, 3 H 106257 2VP60 1 3/8 89652 2BK190H 89659 H x 1 7/16 2 92313 BX93
4, 5 2, 3, 5, 6, 7, 8 H 16150 2VP62 1 3/8 89651 2BK160H 89659 H x 1 7/16 2 92310 B87
6, 7, 8 H 106257 2VP60 1 3/8 89650 2BK130H 89659 H x 1 7/16 2 92415 B82
5, 6 5, 6, 7, 8 H 113808 2VP75 1 5/8 89652 2BK190H 89659 H x 1 7/16 2 92319 BX97
7, 8, 9 H 163900 2MVP60B74P* 1 5/8 89651 2BK160H 89659 H x 1 7/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Totally Enclosed Motors (TEFC)
1 1/2 24 A2, A3 1, 2, 3, 5, 6, 7 H 13580 1VL34 5/8 113800 AK144H 89659 H x 1 7/16 1 92266 A79
8 H 110125 1VP34 7/8 113800 AK144H 89659 H x 1 7/16 1 92266 A79
2 25 A3, A4 5, 6, 7, 8 H 106748 1VL40 7/8 114248 AK154H 89659 H x 1 7/16 1 92217 A81
1, 3 H 111681 1VP50 1 1/8 126006 1B5V200 114033 B x 1 7/16 1 92308 B92
3 26 A3, A4 5, 6, 7 H 110125 1VP34 7/8 163896 1B5V278 114033 B x 1 7/16 1 92314 BX105
1, 2 H 106758 1VL44 7/8 163896 1B5V278 114033 B x 1 7/16 1 163897 A105
A3, A4 1, 3, 8 H 7963 2VP42 1 1/8 164161 2TB300 16177 Q1 X 1 7/16 2 164162 BX112
1, 2 H 110151 1VP44 1 1/8 163896 1B5V278 114033 B x 1 7/16 1 163898 BX108
5 27 1, 2 3, 5, 6, 7, 8 H 110151 1VP44 1 1/8 163896 1B5V278 114033 B x 1 7/16 1 163898 BX108
3, 4, 5 H 111681 1VP50 1 1/8 163899 1B5V250 114033 B x 1 7/16 1 124667 A103
2, 3 H 106257 2VP60 1 3/8 89652 2BK190H 89659 H x 1 7/16 2 92313 BX93
4, 5 5, 6, 7, 8 H 16150 2VP62 1 3/8 89651 2BK160H 89659 H x 1 7/16 2 92310 B87
6, 7, 8 H 106257 2VP60 1 3/8 89650 2BK130H 89659 H x 1 7/16 2 92415 B82
5, 6 6, 7, 8 H 113808 2VP75 1 5/8 89652 2BK190H 89659 H x 1 7/16 2 92319 BX97
7, 8, 9 H 163900 2MVP60B74P* 1 5/8 89651 2BK160H 89659 H x 1 7/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Premium Efficiency Motors (EE)
1 1/2 37 A2, A3 5, 6, 7, 8 H 110125 1VP34 7/8 113800 AK144H 89659 H x 1 7/16 1 92266 A79
2 38 A3, A4 5, 6, 7, 8 H 106748 1VL40 7/8 114248 AK154H 89659 H x 1 7/16 1 92217 A81
3 39 A3, A4 5, 6, 7, 8 H 110125 1VP34 7/8 163896 1B5V278 114033 B x 1 7/16 1 92314 BX105
1, 2 H 106758 1VL44 7/8 163896 1B5V278 114033 B x 1 7/16 1 163897 A105
5 40 1, 2 5, 6, 7, 8 H 110151 1VP44 1 1/8 163896 1B5V278 114033 B x 1 7/16 1 163898 BX108
3, 4, 5 H 111681 1VP50 1 1/8 163899 1B5V250 114033 B x 1 7/16 1 124667 A103
2, 3 H 106257 2VP60 1 3/8 89652 2BK190H 89659 H x 1 7/16 2 92313 BX93
4, 5 5, 6, 7, 8 H 16150 2VP62 1 3/8 89651 2BK160H 89659 H x 1 7/16 2 92310 B87
6, 7, 8 H 106257 2VP60 1 3/8 89650 2BK130H 89659 H x 1 7/16 2 92415 B82
5, 6 5, 6, 7, 8 H 113808 2VP75 1 5/8 89652 2BK190H 89659 H x 1 7/16 2 92319 BX97
7, 8, 9 H 163900 2MVP60B74P* 1 5/8 89651 2BK160H 89659 H x 1 7/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
2 SPEED Motors
2, 3 A3, A4 H 111681 1VP50 1 1/8 126006 1B5V200 114033 B X 1 7/16 1 124607 A92
1, 2 H 110151 1VP44 1 1/8 114028 AK134H 89659 H x 1 7/16 1 92217 A81
1 H 164294 1VP71 1 3/8 163899 1B5V250 114033 B X 1 7/16 1 92307 B108
2 H 163421 1VP65 1 3/8 126006 1B5V200 114033 B X 1 7/16 1 92334 BX96
3, 4 H 164294 1VP71 1 3/8 126006 1B5V200 114033 B X 1 7/16 1 92319 BX97
5, 6, 7 H 161448 1VP60 1 3/8 163422 BK140H 89659 H x 1 7/16 1 92317 BX85
10 51 3, 4 H 91615 2MVP40B54 1 5/8 89651 2BK160H 89659 H x 1 7/16 2 115934 B89
5, 6, 7 5, 6, 7 H 110223 2VP60A 1 5/8 92204 2BK140H 89659 H x 1 7/16 2 92312 B86
8, 9 H 110223 2VP60A 1 5/8 113811 2BK120H 89659 H x 1 7/16 2 92272 B83
BELTS
(See Key on page 15)
OPEN Driproof Motors
BLOWER PULLEY
DV-122 DRIVE TABLE
7 1/2,
10
15,
20
32,
33
34,
35
7 1/2,
10
11,
12
15,
20
15,
16
DISCH
7 1/2,
10
15,
20
41,
42
43,
44
5, 7-
1/2
49,
50
47,
485, 6, 7
5, 6, 7
Form P-DV, Page 20
MOTOR DRIVE AM Opt V - AK Opt MOTOR PULLEY BUSHING
HP AL P/N Model Bore P/N Model P/N Model Qty P/N Model
3 9 A3, A4 H 13580 1VL34 5/8 163896 1B5V278 115949 B x 1 11/16 1 92314 BX105
H 110125 1VP34 7/8 163896 1B5V278 115949 B x 1 11/16 1 92314 BX105
5 10 A3, A4 H 110125 1VP34 7/8 163896 1B5V278 115949 B x 1 11/16 1 92314 BX105
1, 2 H 106748 1VL40 7/8 163899 1B5V250 115949 B x 1 11/16 1 92318 BX100
A3, A4 H 7963 2VP42 1 1/8 164161 2TB300 91608 Q1 x 1 11/16 2 164162 BX112
1, 2 H 110151 1VP44 1 1/8 163896 1B5V278 115949 B x 1 11/16 1 163898 BX108
A4, 1 H 115940 2MVP35B49 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
2, 3 H 106257 2VP60 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
4, 5 H 114249 2VP71 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92306 B95
2, 3 H 163900 2MVP60B74P* 1 5/8 115941 2B5V234 115949 B x 1 11/16 2 163898 BX108
4, 5 H 113809 2VP71A 1 5/8 115942 2B5V184 115949 B x 1 11/16 2 92319 BX97
6, 7 H 113809 2VP71A 1 5/8 114032 2B5V160 115949 B x 1 11/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Totally Enclosed Motors (TEFC)
3 26 A3, A4 5, 6, 7 H 110125 1VP34 7/8 163896 1B5V278 115949 B x 1 11/16 1 92314 BX105
1, 3, 8 H 7963 2VP42 1 1/8 164161 2TB300 91608 Q1 x 1 11/16 2 164162 BX112
5 27 A3, A4 H 7963 2VP42 1 1/8 164161 2TB300 91608 Q1 x 1 11/16 2 164162 BX112
1, 2 H 110151 1VP44 1 1/8 163896 1B5V278 115949 B x 1 11/16 1 163898 BX108
A4, 1 H 115940 2MVP35B49 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
2, 3 H 106257 2VP60 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
4, 5 H 114249 2VP71 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92306 B95
2, 3 H 163900 2MVP60B74P* 1 5/8 115941 2B5V234 115949 B x 1 11/16 2 163898 BX108
4, 5 H 113809 2VP71A 1 5/8 115942 2B5V184 115949 B x 1 11/16 2 92319 BX97
6, 7 H 113809 2VP71A 1 5/8 114032 2B5V160 115949 B x 1 11/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
Premium Efficiency Motors (EE)
3 39 A3, A4 5, 6, 7, 8 H 110125 1VP34 7/8 163896 1B5V278 115949 B x 1 11/16 1 92314 BX105
5 40 A3, A4 H 7963 2VP42 1 1/8 164161 2TB300 91608 Q1 x 1 11/16 2 164162 BX112
1, 2 H 110151 1VP44 1 1/8 163896 1B5V278 115949 B x 1 11/16 1 163898 BX108
A4, 1 H 115940 2MVP35B49 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
2, 3 H 106257 2VP60 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92313 BX93
4, 5 H 114249 2VP71 1 3/8 115942 2B5V184 115949 B x 1 11/16 2 92306 B95
2, 3 H 163900 2MVP60B74P* 1 5/8 115941 2B5V234 115949 B x 1 11/16 2 163898 BX108
4, 5 H 113809 2VP71A 1 5/8 115942 2B5V184 115949 B x 1 11/16 2 92319 BX97
6, 7 H 113809 2VP71A 1 5/8 114032 2B5V160 115949 B x 1 11/16 2 92313 BX93
* USE P2 x 1 5/8" DIA Bushing, P/N 148595
2 SPEED Motors
3 48 A3, A4 5, 6, 7 H 110151 1VP44 1 1/8 164366 1B5V184 115949 B x 1 11/16 1 92315 BX90
A3, A4 H 161448 1VP60 1 3/8 163899 1B5V250 115949 B x 1 11/16 1 92314 BX105
1, 2 H 161448 1VP60 1 3/8 126006 1B5V200 115949 B x 1 11/16 1 92334 BX96
3, 4 H 164294 1VP71 1 3/8 126006 1B5V200 115949 B x 1 11/16 1 92319 BX97
5, 6 H 106257 2VP60 1 3/8 162940 2B5V136 115949 B x 1 11/16 2 92273 B84
10 51 1, 2 H 110223 2VP60 1 5/8 164367 2B5V200 115949 B x 1 11/16 2 92319 BX97
3, 4 5, 6, 7 H 113809 2VP71 1 5/8 164367 2B5V200 115949 B x 1 11/16 2 92318 BX100
5, 6 H 110223 2VP60 1 5/8 162940 2B5V136 115949 B x 1 11/16 2 92310 B87
DV-125 DRIVE TABLE
5, 6, 7, 8
5, 6, 7, 8
5, 6, 7, 8
3, 5, 6, 7, 8
7 1/2,
10
15, 20
32,
33
34,
35
3, 5, 6, 7, 8
5, 7-
1/2
49,
505, 6, 7
7 1/2,
10
15, 20
41,
42
43,
44
6, 7, 8
OPEN Driproof Motors
11,
12
7 1/2,
10
15, 20 15,
16
5, 6, 7, 8
2, 3
2, 3
2, 3, 5, 6, 7,
8
5, 6, 7, 8
DISCHBLOWER PULLEY BELTS
(See Key on page 15)
Drives (cont'd)
Form P-DV, Page 21
Cabinet Parts for Model DV Blower Cabinet Section
151152
15
3
15
1A
15
1B
161
167
151
164
158
Blower
Cabinet
Section
158 - Vertical Discharge
154
158 - Vertical Discharge
Top of Cabinet with Optional Vertical Discharge
109 112 115 118 122 125
151 Blower Access Single wall (no insulation)
Panel Assy (qty is Single wall with insulation
8 for up discharge) Double wall with insulation
151A Door Handle (one per access panel assembly)
151B Door Latch (four per access panel assembly)
152 Discharge Panel Single wall (no insulation) (1)158153 (1)158152 (1)158151 (1)158150 (1)158149 (1)158148
Assy (horizontal Single wall with insulation (1)158708 (1)158709 (1)158710 (1)158711 (1)158712 (1)158713
discharge only) Double wall with insulation (1)158714 (1)158715 (1)158716 (1)158717 (1)158718 (1)158719
153 Duct Connector Assy Horizontal Discharge (1)158724 (1)158725 (1)158726 (1)158727 (1)158728 (1)158729
Vertical (up) Discharge (1)176528 -- (1)176529 -- (1)176530 --
154 Duct flange Vertical (up) Discharge only (2)159897 -- (2)159497 -- (2)159495 --
(2)159898 -- (2)159498 -- (2)159496 --
155 Bulb Seals (around duct Horizontal (2)158829 (2)158831 (2)158833 (2)158835 (2)158837 (4)158834
connector - not illustrated) Discharge only (2)158830 (2)158832 (2)158834 (2)158836 (2)158838
156* Inner Top Horizontal Discharge (2)157355 (2)157355 (2)155792 (2)155792 (2)155551 (2)155551
Vertical (Up) Discharge (1)157355 -- (1)155792 -- (1)155551 --
(1)159904 -- (1)159903 -- (1)159902 --
157* Inner Top Gasket Horizontal or Vertical
158 Outer Top Horizontal Discharge
Vertical (Up) Discharge (1)157357 -- (1)155791 -- (1)155550 --
(1)159901 -- (1)159900 -- (1)159899 --
159* Top Insulation For single or double wall,
Horizontal or Vertical Discharge
160A* Top Liner Double wall with insulation,
Horizontal Discharge
160B* Top Liner Front Double wall with insulation, (1)159917 -- (1)159916 -- (1)159915 --
160C* Top Liner Rear Vertical (Up) Discharge (1)159920 -- (1)159919 -- (1)159918 --
161 Blower Section Corner Post Cover
162* Blower Corner Post Insulation For single or double wall
163* Blower Section Corner Post
164 Blower Section Horizontal Discharge
Center Post Cover Vertical (up) Discharge (4)158349 -- (4)155795 -- (4)155564 --
165* Blower Center Post For single or double wall
Insulation (qty is 4 for up discharge)
166* Blower Section Horizontal Discharge
Center Post Vertical (up) Discharge
167 Corner Hanger for Lifting
168* Motor Top Door Seal
169* Top Support Horizontal Discharge
Insulation Vertical (up) Discharge (2)159939 -- (2)159938 -- (2)159937 --
170* Top Support For single or double wall,
Horizontal Discharge only
171* Bottom Door Angle Horizontal Discharge
172* Bottom Access Panel Angle
173* Motor Shield Horizontal Discharge
Motor Shield Front Vertical (up) Discharge (1)159910 -- (1)159909 -- (1)159908 --
Motor Shield Rear Vertical (up) Discharge (1)159913 -- (1)159912 -- (1)159911 --
174 Flexible Duct Connector part of vibration (1)159541 (1)159542 (1)159543 (1)159544 (1)159545 (1)159546
(canvas; not illustrated) isolation Option PC1
SizeCODE Description
(6)158605 (6)158604 (6)158603
(6)158730 (6)158731 (6)158735
(6)159295 (6)159296 (6)159297
150501
112974
(1)158797 (1)158798 (1)158799
(2)157357 (2)155791 (2)155550
(2)159307 (2)159308 (2)159309
(2)158687 (2)158686 (2)158685
(4)158351 (4)155799 (4)155574
(4)159313 (4)159314 (4)159315
(4)157349 (4)155797 (4)155570
(3)158349 (3)155795 (3)155564
(3)159316 (3)159317 (3)159318
(3)157342 (3)155793 (3)155567
(4)157342 (4)155793 (4)155567
(4)158147
(4)157356 (4)155788 (4)155545
(1)158343 (1)155785 (1)155540
(1)159310 (1)159311 (1)159312
(2)158979 (2)158978 (2)158977
(6)157339 (6)155789 (6)155546
(1)157336 (1)157315 (1)155578
* Internal part - not illustrated
Code 151B -ReplacementDoor Latch,P/N 112974
Form P-DV, Page 22
Burner/
Control
Cabinet
Section
181
182
180191
192
188
183
185
184
186
194197
198 and 1 9 9207
195
Cabinet Parts for Model DV (cont'd) Cabinet Parts - Burner/Control Cabinet Section
* Internal part - not illustrated
109 112 115 118 122 125
180 Control Compartment Right
Doors Left
181 Control Compartment Door Hinge
182 Control Compartment Door Handle
183 Control Box Bottom
184 Control Box Top
185 Control Box Side (gas connection side)
186 Control Box Side (discon
187*
188 Inner Control Single wall (no insulation)
Panel Assy Single wall with insulation
Double wall with insulation
189* Trim Flashing
190 Optional Return Air Single wall (no insulation) -- -- (1)159490 (1)159489 (1)159488 (1)159487
Panel Assy (not Single wall with insulation -- -- (1)160385 (1)160387 (1)160389 (1)160391
illustrated) Double wall with insulation -- -- (1)160386 (1)160388 (1)160390 (1)160392
191 Burner Access Panel Single wall (no insulation)
Assy (with return Single wall with insulation
air, qty is 5) Double wall with insulation
192 Burner Section Corner Post Cover
193* Corner Post Insulation Single or Double Wall
194* Burner Section Corner Post
195 Burner Section Center Post Cover
196* Center Post Insulation Single or Double Wall
197* Burner Sctn Center Post (with return air, qty is 3)
198 Top Rail
199 Top Rail Gasket
200* Profile Mounting Frame
201* Profile Cross Frame
202* Profile Support (Burner)
203* Sensing Probe Box
204* Viewport Clamp
205* Heat Barrier Glass
206* Viewport Gasket
207 Corner Hangers for Lifting
SizeCODE Description
Electric Box Door Assy (inside control box includes
door, hinge, handle, and latches)
(1)157346 (1)157323 (1)155591
(1)157345 (1)157322 (1)155590
(4)158800
(1)155065
(1)157343 (1)157320 (1)155586
(1)157344 (1)157321 (1)155589
(1)155588
(1)155587
(1)162992
(1)158617 (1)158616 (1)158615
(1)159862 (1)159863 (1)159864
(1)159865 (1)159866 (1)159867
(3)158344 (3)157313 (3)155560
(7)158608 (7)158607 (7)158606
(7)159304 (7)159305 (7)159306
(7)159301 (7)159302 (7)159303
(3)155573
(3)159319
(4)155569
(2)155563
(2)159320
(4)155566
(4)158352 (4)157312 (4)155559
(4)158811 (4)158810 (4)158809
(4)158386 (4)157329 (4)155781
(2)158396 (2)157331 (2)155783
(2)158397 (2)157330 (2)155782
(4)155549
(2)158667
(2)159933
(1)159868
(1)159869
Form P-DV, Page 23
Cabinet Parts for Models DV (cont'd)
Model DV Optional Inlet Base and Water Separator
Code 211, Indoor inlet base with three sides closedwith duct flange (Same as Option AVA1)
Code 210, Outdoor inletbase with all sides screened
(Same as Option AVA2)
Code 212, Outdoor inletbase with 2" permanent
filters on all sides (Same as Option AVA3)
CODE 230 - Outside AirWater Separator with 1/2"
Screen for indoor units(use with inlet base OptionAVA1; mount on inlet base
or to building wall)
Inlet Base
109/112 115/118 122/125
210 Inlet Base Pkg - outdoor, Same as 158844 158845 158846
all sides screened Option AVA2
211 Inlet Base Pkg - indoor, insulated, Same as 158841 158842 185543
3 sides closed w/duct flange Option AVA1
212 Inlet Base Pkg - outdoor with 2" Same as 158847 158848 158849
permanent filters on sides Option AVA3
Inlet Base Components - apply to all bases unless specified
213 Inlet Base Bottom (4)155768
214 Inlet Base Corner Post (4)157348 (4)155798 (4)155778
215 Corner Post Insulation, 1" (4)159888 (4)159889 (4)159890
11" x 19" 11" x 27" 11" 46-7/8"
216 Inlet Base Center Post (4)157341 (4)155794 (4)155776
217 Center Post Insulation, 1" (4)159885 (4)159886 (4)159887
2-3/4"x19" 2-3/4"x27" 2-3/4"x46-7/8"
218 Bottom Mounting Angle
219 Top Rail (4)158352 (4)157312 (4)155559
220 Top Rail Gasket, 1/4" x 1-1/4" (4)158811 (4)158810 (4)158809
39" long 46" long 58" long
221 Inlet Base Center Post Cover (4)158348 (4)155796 (4)155777
222 Inlet Base Corner Post Cover (4)158350 (4)157307 (4)155779
223 Trim Flashing (4)158344 (4)157313 (4)155560
224 Lifting Hanger
225 Inlet Screen Support (2)158661 (3)158660 (4)158659
226 Inlet Screen (1)158200 (1)158199 (1)158198
227 Outside Air Duct Assembly Opt AVA1 only (1)158815 (1)158816 (1)158817
228 Inlet Base Panel Assembly Opt AVA1 only (6)159943 (6)159942 (6)159941
229 Filter Module Assembly Opt AVA3 only (8)158690 (8)158689 (8)158688
(including filters, CODE 229A)
229A Replacement Filters, Opt AVA3 only (8)158819 (8)158818 (16)101621
2" Permanent 10" x 12" 15" x 20" 20" x 20"
230 Water Separator 159550 159551 159552
12"x28-1/4" 20"x36-1/4" 39"x47-3/4"
CODE Description
(4)157354
Option AVA1
only
Same as
Option AS15
(4)155583
(4)155549
Size
Option AVA1
only
Form P-DV, Page 24
Model DV Optional Filter Cabinet
243
239
247A247B244
Door Side ViewThe optionalfilter cabinet is"stacked" ontop of the inletbase.
* Internal parts that are not
shown in the illustration.
242 - Corner post cover (notillustrated) - on corners opposite thedoor side245 - Center post cover (not illustrated)is between the two side panels on allsides except door side246 - Side panels (not illustrated) - twoon each of the other three sides
109/112 115/118 122/125
231 Filter Section with 2" Disposable Filters Same as Option AW13 159226 159227 159228
232 Filter Section with 1" Permanent Filters Same as Option AW3 159229 159230 159231
233 Filter Section with 2" Permanent Filters Same as Option AW6 159232 159233 159234
234 Filter Section with 1" Pleated Filters Same as Option AW14 159235 159236 159237
235 Filter Section with 2" Pleated Filters Same as Option AW15 159238 159239 159240
Filter Section Cabinet Parts - apply to all filter sections
236* Filter Section Door Corner Post
237* Filter Section Corner Post
238* Filter Section Center Post
239 Top Rail (4)158352 (4)157312 (4)155559
240* Trim Flashing (4)158344 (4)157313 (4)155560
241* Lifting Hanger (4)155549 (4)155549 (4)155549
242 Filter Section Corner Post Cover
243 Filter Section Door Right Corner Post Cover
244 Filter Section Door Left Corner Post Cover
245 Filter Section Center Post Cover
246 Filter Section Side Panel Assembly
247A Filter Section Door Assembly (1)158650 (1)158651 (1)158652
247B Filter Section Door with Handle (1)158653 (1)158654 (1)158655
V-Bank Filter Rack Components (assembled with #10x1/2" lg sheetmetal screws) and Filters - not illustrated
248 Top Filter Channel Assembly (2)158647 (3)158648 (4)158649
249 Filter Channel Angle (4)158389 (6)158388 (8)158387
250 Bottom Filter Support
251 Filter Channel (riveted to bottom filter support) (4)158381 (6)158380 (8)155595
252 Filter Channel Angle (6)158389 (8)158388 (10)158387
253 Bottom Blockoff (2)158392 (2)158391 (2)158390
254 Replacement Filters 2" Disposable, 16" x 16" (4)104101 -- (16)104101
2" Disposable, 16" x 20" (4)104097 (6)104097 --
2" Disposable, 16" x 25" -- (6)104099 (6)104099
1" Permanent, 16" x 16" (4)104102 -- (16)104102
1" Permanent, 16" x 20" (4)101607 (6)101607 --
1" Permanent, 16" x 25" -- (6)101609 (6)101609
2" Permanent, 16" x 16" (4)104103 -- (16)104103
2" Permanent, 16" x 20" (4)101620 (6)101620 --
2" Permanent, 16" x 25" -- (6)101622 (6)101622
1" Pleated, 16" x 16" (4)104104 -- (16)104104
1" Pleated, 16" x 20" (4)104105 (6)104105 --
1" Pleated, 16" x 25" -- (6)104107 (6)104107
2" Pleated, 16" x 16" (4)104109 -- (16)104109
2" Pleated, 16" x 20" (4)104110 (6)104110 --
2" Pleated, 16" x 25" -- (6)104112 (6)104112
SizeCODE Description
(2)155572
(2)155571
(3)155568
(2)158366
(1)158367
(1)158195
(3)155565
(6)158664
(6)155582
800-695-1901; www.RezSpec.com©2005 Thomas & Betts Corporation, All rights reserved. Printed in U.S.A.
MANUFACTURER OF GAS, OIL, ELECTRIC HEATING AND VENTILATING SYSTEMS
905 Form RZ-NA-P-DV (Version A)