drawer slides
TRANSCRIPT
Drawer Slides
Dra
wer
Slid
es
6
Side Mounting Drawer Slides
Special Features
! New smooth, silent roller system.
! Right side pair has lateral guiding.
! Left side pair has side gap adjustment.
! Tilt and remove of drawer.
! Stopper to prevent drawer from falling.
! New “Auto-Closing” feature of drawer.
! “System 32” compatible.
! Ribs provided for strength.
! Load capability - 20 kgs.
37.00
17.259.0
2.0
13.2
0
2.00
37.00Front Edgeof Cabinet
128.00 96.00 96.00 96.00 96.00
250
300
350
375400
450
500
525550
600
9.00
31.50 128.00 128.00 128.00 128.00 128.00
650
700
750
Drilling Diagram for Cabinet
Design Reg. No: 159024/87
7
Specifications
PowderCoatedBlack,BrownandIvory
Code Nos.
12.7(1/2”)
20
15.6(5/8”)
Length(mm)
Extension(mm)
Gap/Side(mm)
Max.LoadKgs.
Finish
SMDS 25 250 160
SMDS 30 300 210
SMDS 35 350 260
SMDS 37 375 285
SMDS 40 400 310
SMDS 45 450 360
SMDS 50 500 410
SMDS 52 525 435
SMDS 55 550 460
SMDS 60 600 510
* SMDS 65 650 560
* SMDS 70 700 610
* SMDS 75 750 660
For efficiency and durability.
1. Side gap of 12.7 mm (1/ 2”) and 15.6 mm (5/ 8”) per side is most important.
2. Fix slides parallel and at equal height.
Caution
SIDE VIEWFig. 2
25.4
mm
1"2.0
FIXED SLIDE
MOVING SLIDE
DRAWER
Top
Cle
aran
ce
CABINET
2.0
FRONT VIEWFig. 1
12.7
7.0
1/2"
1. Side gap of 12.7 mm (1/2”) per side required (Refer fig. 1).
2. Side gap of 15.6 mm (5/8”) per side is required for 650, 700 and 750 mm.
3. 25.4 mm (1”) clearance from top edge of drawer required to tilt and remove drawer
(Refer fig. 2).
4. Fixed and moving slide should be equally offset by 2 mm for Auto-Closing (Refer fig. 2).
5. Recess screw heads to avoid interference.
6. A set of slides must be fitted parallel and at same heights to each other.
Fitting Instructions
Fig. 3 Side Mounting D' Slide for Steel Furniture
12.7
1/2"
STEELCABINET
STEELDRAWER
WOODENDRAWER
12.7
1/2"
For Side Mounting Bottom Slide - EURO add 'E-' before the existing codes.* Not available in EURO series.For Side Mounting Bottom Slide - EURO add 'E-' before the existing codes.* Not available in EURO series.
! New smooth silent roller system.
! Right side pair has lateral guiding.
! Left side pair has side gap adjustment.
! Tilt and remove of drawer.
! Stopper to prevent drawer from falling.
! New ''Auto-Closing'' feature of drawer.
! ''System-32'' Compatible.
! Ribs provided for strength.
! Load capability - 20 Kgs.
37.00
17.259.0
2.0
13.2
0
2.00
37.00Front Edgeof Cabinet
128.00 96.00 96.00 96.00 96.00
250
300
350
375
400
450
500
525
550
600
9.00
Bottom Mounting Drawer Slides
Special Features
Drilling Diagram for Cabinet
SIDE VIEW
7.0
14.5
12.5
1/2’’
12.7
Fig. 1
8
Bottom Mounting D’ Slide for Steel Furniture
STEELCABINET
WOODENDRAWER
6.0
1/2’’
12.7
STEELCABINET
STEELDRAWER
6.0
1/2’’
12.7
1. Side gap of 12.7 mm (1/2”) per side required (Refer fig. 1).
2. 25.4 mm (1”) clearance from top edge of drawer required
to tilt and remove drawer (Refer fig. 2).
3. Fixed and moving slide should be equally offset by 2 mm
for Auto-Closing (Refer fig. 2).
4. Recess screw heads to avoid interference.
5. A set of slides must be fitted parallel and at same heights
to each other.
Fitting Instructions
For efficiency and durability.
1. Side gap of 12.7 mm (1/ 2”) per side is most important.
2. Fix slides parallel and at equal height.
Caution
Specifications
1"
2.0
FIXED SLIDEMOVING SLIDE
DRAWER
25.4
mm
Top
Cle
aran
ce
CABINET
2.0
SIDE VIEWFig. 2
Code Nos.Length(mm)
Extension(mm)
Euro Extension (mm)
For Bottom Mounting Bottom Slide - EURO add 'E-' before the existing codes.
PowderCoatedBlack,Brown,Ivoryand
Sliver
Gap/Side(mm)
Max.LoadKgs.
Finish
12.7(1/2”)
20
BMDS 30 300 225 210
BMDS 35 350 275 260
BMDS 37 375 300 285
BMDS 40 400 325 310
BMDS 45 450 375 360
BMDS 50 500 425 410
BMDS 52* 525 450 -
BMDS 55 550 475 460
BMDS 60 600 525 510
* Not available in EURO series.
9
12
Full Panel Drawer Slides
Lengthmm
Extensionmm
Height (mm)/Code Nos.
54 86 125
FPDS 54-30 FPDS 86-30 FPDS 125-30
FPDS 54-35 FPDS 86-35 FPDS 125-35
FPDS 54-40 FPDS 86-40 FPDS 125-40
FPDS 54-45 FPDS 86-45 FPDS 125-45
FPDS 54-50 FPDS 86-50 FPDS 125-50
FPDS 54-55 FPDS 86-55 FPDS 125-55
FPDS 54-60 FPDS 86-60 FPDS 125-60
PowderCoatedBlack,Brownand
Ivory.
Finish
300 225
350 275
400 325
450 375
500 425
550 475
600 525
Special Features
! Simplifies construction of drawer as it eliminates the sides of
drawer.
! Saves wood, labour, drawer space, time and cost, which
enhances bulk production.
! Tilt and remove capability with guiding.
! Auto closing of drawer.
! Front facia adjustment.
! Ribbed for strength.
! Precision rollers for smooth running.
! Load capability - 25 kgs.
! "System 32'' compatible.
! Stopper prevents drawer from falling.
! Also available with 6 mm bottom track easy to fit and helps in faster
assembly, as it does not require screwing the bottom, using 6 mm board in
place of 9 mm or 12 mm.
Drilling Diagram for Cabinet ( 6mm Bottom Track )
Front Edge of Cabinet
600
37.00
9.00128.00 96.00 96.00 96.00 96.00
2.00
550
525
500
450
400
375
350
300
Specifications
10
For efficiency and durability.
1. Strictly maintain side gap of 15.5 mm per side.
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
Caution
1. Side gap of 15.5 mm per side is required and acts as side panel of
drawer. (Refer fig 1).
2. Clearance of 25mm from top edge of drawer required to tilt and
remove drawer. (Refer fig 2).
3. Fixed slide should be set by 2mm for auto-closing. (Refer fig 2).
4. Screws should be recessed to avoid fouling.
5. Fixed slides should be fitted parallel and at equal height to each other.
6. Front fascia is to be fitted into front brackets which have 2-way
adjustment for alignment.
Fitting Instructions
A B C D(mm) (mm) (mm) (mm)
54 71 52 32
86 103 84 64
125 142 123 96
150 167 148 96
SIDE VIEWFig.2
FRONT VIEWFig.1
8.5
15.5
17.01.3
A D CB
Wooden Shelf
Full Panel with 6mm Bottom Track
CABINETTop
Cle
aran
ce
25.4
(1")
Full PanelSlide
2 mm
Fixed Slide
Code Numbers / HeightLength
mmExtension
mmFinish
375
350 275
300 225
400
525
550
450
475
425
375
325
300
450
500
PowderCoatedBlack,Brownand
Ivory.
FULLPANEL BOTTOM TRACK
54 86 125 150
FPDS 54 30-6 FPDS 86 30-6 FPDS 125 30-6 FPDS 150 30-6
FPDS 54 35-6 FPDS 86 35-6 FPDS 125 35-6 FPDS 150 35-6
FPDS 54 37-6 FPDS 86 37-6 FPDS 125 37-6 FPDS 150 37-6
FPDS 54 40-6 FPDS 86 40-6 FPDS 125 40-6 FPDS 150 40-6
FPDS 54 45-6 FPDS 86 45-6 FPDS 125 45-6 FPDS 150 45-6
FPDS 54 50-6 FPDS 86 50-6 FPDS 125 50-6 FPDS 150 50-6
FPDS 54 52-6 FPDS 86 52-6 FPDS 125 52-6 FPDS 150 52-6
FPDS 54 55-6 FPDS 86 55-6 FPDS 125 55-6 FPDS 150 55-6
FOUR HEIGHTS
150mm125mm
86mm54mm
11
15.5
250.
0
64.0
64.0
64.0
248.
0
267.
0
15.0
Front View
Bottom GuideFig. 1
Side ViewFig. 2
CABINETTop
Cle
aran
ce25
.4 (1
")
2 mm
Full panelSlide
Fixed Slide
Special Features
Specifications
Power Coated
Black, Brown &
Ivory
Code No. Length(mm)
Extension(mm)
Finish
! Simplifies construction of drawer as it eliminates the sides of drawer.
! Saves Wood, Labour and Drawer space.
! Tilt & remove capacity with guiding.
! 'Auto-Closing' of drawer.
! Front facia adjustment.
! Ribbed fro strength.
! Precision rollers for smooth running.
! 25 Kgs. load capability.
! 'System 32' Compatible.
! Stopper prevents Drawer from falling.
! Available with 6 mm bottom track is easy to fit and helps in faster
assembly, as it does not require screwing the bottom, using 6 mm board in
place of 9 mm or 12 mm.
Fitting Instructions
1. Side gap of 15 mm is required and acts as side panel of drawer. (Fig. 1)
2. 25 mm clearance from top edge of drawer required to tilt and remove
drawer. (Fig. 2)
3. Fixed slide should be set by 2 mm for 'Auto-Closing.' (Fig. 2)
4. Screws should be recessed to avoid fouling.
5. Fixed slides should be fitted parallel and at equal heights to each other.
6. Front facia is to be fitted into front brackets which have 2 way adjustment
for alignment.
Caution :
For efficiency and durability.
1. Strictly maintain side gap of 15.5 per side.
2. Fix slides are parralel and equal height.
3. Do not apply pain or polish.
FPDS 250 40-6 400 325
FPDS 250 45-6 450 375
FPDS 250 50-6 500 425
Full Panel Drawer Slides 250
12
11
FinishLength
mmExtension
mm
Gap/Sidemm
Max.LoadKgs.
3015.5
Height (mm)/Code Nos.
54 86 125 150
FFDS 54-30 FFDS 86-30 FFDS 125-30 FFDS 150-30
FFDS 54-35 FFDS 86-35 FFDS 125-35 FFDS 150-35
FFDS 54-37 FFDS 86-37 FFDS 125-37 FFDS 150-37
FFDS 54-40 FFDS 86-40 FFDS 125-40 FFDS 150-40
FFDS 54-45 FFDS 86-45 FFDS 125-45 FFDS 150-45
FFDS 54-50 FFDS 86-50 FFDS 125-50 FFDS 150-50
FFDS 54-52 FFDS 86-52 FFDS 125-52 FFDS 150-52
FFDS 54-55 FFDS 86-55 FFDS 125-55 FFDS 150-55
FFDS 54-60 FFDS 86-60 FFDS 125-60 FFDS 150-60
PowderCoatedBlack,Brownand
Ivory.
300 335
350 385
375 410
400 435
450 485
500 535
525 560
550 585
600 635
! Simplifies construction of drawer as it eliminates the sides of drawers.
! Saves wood, labour, drawer space, time & cost.
! Full extension of drawer provided.
! Slide latches and wheel catches provided on both sides to prevent the
slides from getting disengaged while working.
! Auto-closing of drawer.
Special Features
Front Edge of Cabinet
600
550
500 & 525
450
400
350 & 375
300
64.00
64.00
64.00
96.0096.0096.0096.00128.0032.00
6.00
Drilling Diagram for Cabinet
Specifications
! Front fascia adjustment.
! Ribbed for strength.
! Ideal for filing drawers where full extension of drawer
is necessary.
! System-32 compatible.
! 25 kgs load capacity.
Full Panel Full Extension Drawer Slides
13
For efficiency and durability.
1. Side gap of 15.5 mm per side is most important.
2. Fix slides parallel and at equal height.
Caution
Fig.3
Fig.5
Fig.1 FRONT VIEW
A
8.5
D C B
15.5
1. To install Full Panel Full Extension Drawer Slide a 15.5mm gap per
side is required between cabinet and drawer. A total of 31 mm for
both sides (Refer fig.1).
2. Fit the outer slide onto the inside of the cabinet
(Refer fig.2). Leave 6mm from the front edge.
3. Assemble the intermediate slide with the outer slide and slide it
forward till it stops (Refer fig.3).
4. Complete the drawer by adding front, back and bottom panels to
the Full Panel. Make sure the slide latches (red color) is pulled
forward (Refer fig.4B).
5. Slide the full panel into the intermediate slide
(Refer fig.5). Move the slide latch backward to the locked position
(Refer fig.4A).
6. For removal of drawer, move slide latches (Red color) forward. The
drawer can now be tilted and removed. (Refer fig.4B).
7. Slides should be fitted parallel to each other and screws tightened
fully, to avoid gaps or interference with wheels.
Fitting Instructions
A B C D(mm) (mm) (mm) (mm)
54 90 79 32
86 122 111 64
125 161 150 96
150 186 175 128
Fig.4
SLIDE LATCH POSITION
FORWARDTO ASSEMBLEOR TO REMOVE
BACKWARDTO LOCK
Fig.2
6 0.
B A
14
11
Fullpanel Quick Fit
Design Reg. No: 202444
Special Features
Specifications
Fitting Instructions
! A unique new way to assemble a drawer by
clipping on a matching back panel.
! This not only improves the look of the drawer but
also saves valuable time during assembly and
brings down cost.
! Tilt and remove capability with guiding.
1. Side gap of 15.5mm is required and acts as side panel of drawer (Fig.1).
2. 25mm clearance from top edge of drawer required to tilt and remove drawer (Fig. 2).
3. Fixed slide should be set by 2mm for 'Auto-Closing’ (Fig. 2).
4. Screws should be recessed to avoid fouling.
5. Fixed slides should be fitted parallel and at equal heights to each other.
6. Insert the Rear panel onto the Side panels through the key slot provided in the side panels (Ref. Fig.3).
7. Place the bottom flap through the track provided in the Side panels and fix the front facia with the
Bracket and insert the unit onto Fixed slides which are fitted internal sides of cabinet (Ref. Fig.4).
Caution
1. Strictly maintain side gap of 15.5mm per side
2. Fix slides are parallel and at equal height.
3. Do not apply paint or polish.
! Autoclosing of drawer.
! Front facia adjustment.
! Precision rollers for smooth running.
! 'System 32' compatible.
For efficiency and durability:
Fig. 4 Fig. 3
Fig. 2 SIDE VIEW
Fig.1
15.5
FRONT VIEW
ABCD
CABINETTop
Cle
aran
ce
25.4
(1")
Fixed Slide
2 mm
Full PanelSlide
325
375
325
375
325
375
25
PowderCoatedBlack,Brown &Ivory.
FPQ 54-40-40 54 400 400
FPQ 54-40-45 54 400 450
FPQ 54-45-40 54 450 400
FPQ 54-45-45 54 450 450
FPQ 86-40-40 86 400 400
FPQ 86-40-45 86 400 450
FPQ 86-45-40 86 450 400
FPQ 86-45-45 86 450 450
FPQ 125-40-40 125 400 400
FPQ 125-40-45 125 400 450
FPQ 125-45-40 125 450 400
FPQ 125-45-45 125 450 450
Code Nos. Height Depth Width Extension MaxLoad kgs.
Finish
A B C D(mm) (mm) (mm) (mm)
54 71 52 32
86 103 84 64
125 142 123 96
15
Fullpanel Quick Fit File Drawer
Fig.7Fig.6
1 .51 5
152.
096
.0
'A'
10 deep8.0Ø
Special Features
! Special raised rear panel is ideal for filing cabinets.
! A unique new way to assemble a drawer by clipping on a
matching back panel.
! This not only improves the look of the drawer but also saves
valuable time during assembly and brings down cost.
! Tilt and remove capability with guiding.
! Autoclosing of drawer.
! Front facia adjustment.
! Precision rollers for smooth running.
! ‘System 32’ compatible.
1. Side gap of 15.5mm is required and acts as side panel of drawer (Fig. 1).
2. Fixed slide should be set by 2mm for ‘Auto-closing’ (Fig. 2).
3 Screws should be recessed to avoid fouling.
4. Fixed slides should be fitted parallel and at equal heights to each other.
5. Insert the raised rear panel on to the side panels through the key slot provided in the side panels
(Ref. Fig. 3).
6. Slide the 6mm bottom panel through the tracks provided in the side panels. (Ref. Fig. 4).
7. Connect the cross rods by using T-connectors as shown in diagram (Ref. Fig. 5).
8. Screw the front facia with side panels and insert the dowel in to the Ø8 hole made in front facia
screw the side rods in to dowels (Ref. Fig. 6). Push the other end of the rod in to the rubber
bushes fitted on the raised rear panel (Ref. Fig. 7).
Fitting Instructions
Fig.1 FRONT VIEW
15.5
125.
0
96.0
123.
0
142.
0
Fig.3SIDE VIEW
Fig.2
CABINET
2mm
Fixed Slide
Full PanelSlide
Specifications
325
375
FPQ 125-40-40 F 125 400 400
FPQ 125-40-40 FG1 125 400 400
FPQ 125-40-45 F 125 400 450
FPQ 125-40-45 FG2 125 400 450
FPQ 125-45-40 F 125 450 400
FPQ 125-45-40 FG3 125 450 400
FPQ 125-45-45 F 125 450 450
FPQ 125-45-45 FG4 125 450 450
25
PowderCoatedBlack,Brown &Ivory.
* With Gallery fitting set.
Code Nos. Height Depth Width Extension MaxLoad kgs.
Finish
Design Reg. No: 207641
Fig.4
Fig.5
16
Full Panel Quick Fit Full Extension
Special Features
Fitting Instructions
1. To install Full Panel Full Extension Drawer Slide a 15.5mm gap per side is required between cabinet and drawer. A total of 31 mm for both sides. (Refer Fig.1)
2. Insert the Rear panel onto the Side panels through the key slot provided in the side panels. (Ref. Fig.2)
3. Place the bottom flap through the track provided in the Side panels and fix the front facia with the Bracket.(Ref. Fig.3)
4. Fit the outer slide onto the inside of the cabinet. Leave 6 mm from the front edge. (Refer Fig.4)
5. Assemble the intermediate slide with the outer slide and slide it forward till it stops. (Refer Fig. 5)
6. Complete the drawer by adding front, back and bottom panels to the Full Panel, Make sure the slide latches (red color) is pulled forward. (Refer Fig. 6B)
7. Slide the Full panel into the intermediate slide. Refer Fig.7. Move the slide latch backward to the locked position. (Ref. Fig.6A)
8. For removal of drawer, move slide latches(Red color) forward. The drawer can now be tilted and removed. (Ref. Fig.6B)
9. Slides should be fitted parallel to each other and screws tightened fully, to avoid gaps or interference with wheels.
! A unique new way to assemble a drawer by clipping on a matching back panel.
! This not only improves the look of the drawer but also saves valuable time
during assembly and brings down cost.
! Tilt and remove capability with guiding.
! Full extension of drawer provided.
! Slide latches and wheel catches provided on both sides to prevent the slides
from getting disengaged while working.
! 'Auto-Closing' of drawer.
! Front facia adjustment.
! Ribbed for strength.
! 'System 32' Compatible.
! 25 Kgs. of load capacity.
Specifications
Code Nos. Height Depth Extension Max. LoadKgs.
Finish
FFQ 125-40-40 125 400 400
FFQ 125-40-45 125 400 450
FFQ 125-45-40 125 450 400
FFQ 125-45-45 125 450 450
Width
485
435
25
PowderCoatedBlack,Brown
&Ivory
Fig. 1
161.
0
15.5
150.
0
96.0
125.
0
8.5
17.0
17
Fig. 3Fig. 2
Fig. 5Fig. 4
Fig. 7Fig. 6
6.0
SLIDE LATCH POSITION
B A
FORWARDTO ASSEMBLEOR TO REMOVE
BACKWARDTO LOCK
18
19
Special Features
Full Panel Quick Fit Full Extension File Drawer
! Special Raised rear panel is ideal for filing cabinets.
! A unique new way to assemble a drawer by clipping on a matching back panel.
! This not only improves the look of the drawer but also saves valuable time during
assembly and brings down cost.
! Full extension of drawer provided.
! Tilt and remove capability with guiding.
! Autoclosing of drawer.
! Front facia adjustment.
! Precision rollers for smooth running.
! System 32 compatible.
1. To install Full Panel Full Extension Drawer Slide a 15.5 mm gap per side is required between
cabinet and drawer. A total of 31 mm for both sides. (Ref. Fig.1)
2. Insert the Raised Rear panel onto the side panels through the key slot provided in the side
panels. (Ref. Fig.2)
3. Slide the 6 mm bottom panel through the tracks provided in the side panels.( Ref. Fig.3)
4. Connect the cross rods by using T- connectors as shown in diagram.(Ref.Fig.4)
5. Fix the front facia with side panels by using the clip-on mechanism and lock it by rotating the
lever as shown in diagram and insert the dowel into the Ø8 mm hole made in front facia and
screw the rods in it. (Ref. Fig. 5). Push the other end of the rod into the plastic sleeves fitted on
the Raised rear panel. (Ref. Fig.6)
6. Fit the fixed slide onto the inside of the cabinet. Leave 6 mm from the front edge. (Ref. Fig.7)
7. Assemble the intermediate slide with the fixed slide and slide it forward till it stops. (Ref. Fig. 8)
8. Slide the File drawer assembly into the intermediate slide. (Ref. Fig.10). Make sure that the
slide latches(red colour) are pulled forward.(Ref.Fig.9B) After engaging the drawer assembly
into the intermediate slide move the slide latches backward to the locked position. (Ref.Fig.9A)
9. For removal of drawer, move slide latches(Red color) forward. The drawer can now be tilted
and removed. (Ref. Fig. 9B)
10. Slides should be fitted parallel to each other and screws tightened fully, to avoid gaps or
interference with wheels.
Fitting Instructions
125.
0 161.
0
150.
096
.0
8.5
17.0Fig. 1
15.5
Fig. 2
Specifications
Code No. Height Depth Width ‘A’ Extn. Max. LoadKgs.
Finish
FFQ 125-40-40 F 125 400 400 340
*FFQ 125-40-40 FG1 125 400 400 340
FFQ 125-40-45 F 125 400 450 390
*FFQ 125-40-45 FG2 125 400 450 390
FFQ 125-45-40 F 125 450 400 340
*FFQ 125-45-40 FG3 125 450 400 340
FFQ 125-45-45 F 125 450 450 390
*FFQ 125-45-45 FG4 125 450 450 390
435
485
25
Powder CoatedBlack, Brown &Ivory
*with gallery fitting set
Design Reg. No. 207640
20
Fig. 3 Fig. 4
Fig. 5
Ø8.0
10 de pe
Ø8.0 x 12.0 Min.
32.0
T E ER
ROTA E L V O OCK
T L
Fig. 6
Fig. 8Fig. 7
6.0
Fig. 10Fig. 9
SLIDE LATCH POSITION
FORWARDTO ASSEMBLEOR TO REMOVE
BACKWARDTO LOCK
B A
189.
0
2.5A' '
Full Extension Drawer Slides
Design Reg. No: 181904/00
FEDS 30 300 335
FEDS 35 350 385
FEDS 37 375 410
FEDS 40 400 435
FEDS 45 450 485
FEDS 50 500 535
FEDS 52 525 560
FEDS 55 550 585
FEDS 60 600 635
Code Nos.
Powdercoated-Black,Brown,Ivoryand
Silver.
Length(mm)
Extension(mm)
Gap/Side(mm)
Max.Load(Kgs.)
Finish
12.7(1/2”)
30
! Full extension of drawer provided.
! Slide latches and wheel catches provided on both
sides to prevent the slides from getting disengaged
while working.
! Inner Slide has Bottom Mounting.
Special Features
Front Edge of Cabinet
600
550
500 & 525
450
400
350 & 375
300
64.00
64.00
64.00
96.0096.0096.0096.00128.0032.00
6.00
Drilling Diagram for Cabinet
Specifications
! Screw holes as per System 32.
! Lateral guiding provided.
! 25 kgs load capacity.
! Ideal for kitchen baskets where full extension of drawer
is necessary.
21
22
1. To install Full Extension Drawer Slide a 12.7mm (1/2")
gap per side is required between cabinet and drawer. A
total of 25.4mm ( 1") for both sides (Refer fig. 1).
2. Fit the outer slide onto the inside of the cabinet (Refer
Fig.2).
3. Assemble the intermediate slide with the outer slide and
slide it forward till it stops (Refer fig. 3).
4. Fit the inner slide onto the drawer. Make sure the slide
latches (red color) is pulled forward (Refer fig. 4B).
5. Slide the inner slide with the drawer into the intermediate
slide (Refer fig. 5). Move the slide latch backward to the
locked position (Refer fig 4A).
6. For removal of drawer, move slide latches (Red color)
forward. The drawer can now be tilted and removed.
7. Slides should be fitted parallel to each other and screws
tightened fully, to avoid gaps or interference with wheels.
Fitting Instructions
Fig.5
Fig.3
Fig.1 FRONT VIEW
7.0
60.0
50.0
1/2"12.7
Drawer
Cab
inet
Fig.2
6.0
Caution
For efficiency and durability.
1. Side gap of 12.7 mm (1/2") per side is most important.
2. Fix slides parallel and at equal height.
3. Do not remove Red Latch.
Fig.4
SLIDE LATCH POSITION
FORWARDTO ASSEMBLEOR TO REMOVE
BACKWARDTO LOCK
BA
23
Fascia Swivel Bottom Mounting Drawer Slides
Special Features
! Specially designed fascia swivel is ideal for
locking computer keyboards when not in use.
! Right side with lateral guiding.
! Tilt and remove of drawer.
! New ‘auto-closing’ feature.
! ’System 32’ compatible.
Specifications
Code No.Extension
(mm)Max. Load
Kgs.Gap/Side
(mm)
Fitting Instructions
1. Side gap of 12.7mm (1/2”) per side required (Ref. Fig. 1)
2. 25.4mm (1”) clearance from top edge of drawer required to tilt and remove
drawer (Ref. Fig. 2)
3. Fixed and moving slide should be equally offset by 4mm for “Auto-closing”
(Ref. Fig. 2)
4. Recess screw heads to avoid interference.
5. Screw front facia bracket to the facia panel (Ref. Fig. 3.)
6. Front facia can be lifted and tilted in 90° (Ref. Fig.4)
7. While closing the drawer, rotate the front facia and lock the facia bracket in
slot provided in the slide (Ref. Fig. 5)
FRONT VIEWFig. 1
SIDE VIEWFig. 2
Fig. 4 Fig. 5
1/2’’
12.7
FIXED SLIDEMOVING SLIDE
DRAWER
25.4
mm
Top
Cle
aran
ce
CABINET
2.0
1 "
BMDS 35 FS 350 260
BMDS 40 FS 400 310 12.7
BMDS 45 FS 450 360 (1/2”) 20
BMDS 50 FS 500 410
Fig. 3
Length(mm)
24
Sleek Telescopic Drawer Slide (I)
Special Features
Drilling Diagram for Cabinet
! Precision ball bearing.
! Full extension of drawer.
! Load capacity 35 Kgs.
! Direct fitting from front.
! Removable drawer with Latch
! System 32 installation.
250
300
350
400
450
500
550
600
750
900
32.0 32.0 32.0
32.0 32.0
32.0 32.0
64.0 32.0 32.0
32.0 32.0
64.0 32.0 32.0
64.0 64.0 32.0
64.0 32.0 32.0
32.0 32.0
32.064.064.064.096.096.096.096.064.064.064.032.032.0
Front Edgeof Cabinet
DRILLING DIAGRAM FOR CABINET
.2Ø4
25
Specifications
Fitting Instructions
1. To install sleek telescopic drawer slide 12.7 to13.0mm side gap per
side is required between cabinet and drawer. (Refer Fig. 1)
2. Depress latch and remove the inner slide. (Refer Fig. 2)
3. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can
be got through slots in intermediate slide
4. Slides should be fitted parallel and screws tightened fully to avoid gaps.
5. Fit inner slide onto the outside of the drawer.
6. Now slide the drawer with inner slide fluted on to the intermediate slides
on the cabinet till the latch will automatically engage.
Code No. Length(mm)
Extension(mm)
Max. LoadKgs.
Gap/Side(mm)
Finish
White,Black, MG GrayZinc Plated
STDS 25 (I) 250 260
STDS 30 (I) 300 310
STDS 35 (I) 350 360
STDS 40 (I) 400 410
STDS 45 (I) 450 460 12.7
STDS 50 (I) 500 510 to 35
STDS 55 (I) 550 560 13.0
STDS 60 (I) 600 610
STDS 75 (I) 750 760
STDS 90 (I) 900 910
CautionFor efficiency and durability:
1. Strictly maintain 12.7 to 13.Omm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
13.0
12.7
13.045
.0
CAB
INET
12.7
3.2
1/8"CABINET
DRAWERMinimumBottomClearance
Fig. 1
Fig. 2
Depress Latchto Remove Inner Slide
26
Sleek Telescopic Drawer Slides-Auto Closing (I)
! New Auto closing feature.
! Precision ball bearing.
! Full extension of drawer.
! Load capacity 35 Kgs.
! Direct fitting from front.
! Removable drawer with latch.
! System 32 installation.
Fitting Instructions
1. To install sleek telescopic drawer slide 12.7 to13.0mm side gap per
side is required between cabinet and drawer. (Refer Fig. 1)
2. Depress latch and remove the inner slide. (Refer Fig. 2)
3. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can
be got through slots in intermediate slide
4. Slides should be fitted parallel and screws tightened fully to avoid gaps.
5. Fit inner slide onto the outside of the drawer.
6. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch will automatically engage.
Special Features
CautionFor efficiency and durability:
1. Strictly maintain 12.7 to 13.Omm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
Specifications
Code No. Length(mm)
Extension(mm)
Max. LoadKgs.
Gap/Side(mm)
Finish
White,Black, MG GrayZinc Plated
STDS 25-AC(I) 250 245
STDS 30-AC(I) 300 295
STDS 35-AC(I) 350 345
STDS 40-AC(I) 400 395
STDS 45-AC(I) 450 445 12.7
STDS 50-AC(I) 500 495 to 35
STDS 55-AC(I) 550 545 13.0
STDS 60-AC(I) 600 595
STDS 75-AC(I) 750 745
12.713.0
45.0
DRAWERMinimumBottomClearance
CABINET
CAB
INET
3.2
1/8"
Fig. 1
Fig. 2
Depress Latchto Remove Inner Slide
27
Special Features
Mini Drawer Slide H-17
1. Lateral play is virtually eliminated when the
groove mounting method is employed.
2. This slide is small, elegant and space saving.
3. Accessible from both sides.
4. 32mm hole pattern.
5. Max. load capability - 10kg/set.
Specifications
MDS 21 214-341 214 214 70
MDS 31 310-506 310 310 94
MDS 37 374-616 374 374 104
MDS 43 438-726 438 438 122
Drawer Depthmm
Length of drawerslide ‘L1’ mm
Item CodeLength of cabinet
slide ‘L2’ mmExtension loss of drawer ‘A’ mm
Fitting Instructions
1. Side gap required is 10.0mm per side including
the groove (Ref. Fig. 1).
2. Make a groove in the drawer as per given
dimensions (Ref. Fig. 1).
3. Fix the cabinet slide to the cabinet (Ref. Fig. 2).
4. Fix the drawer slide to the drawer with the M4
screws provided (Ref. Fig. 2).
±0.210.0
±0.
225
.5
Caution
1. Side gap required is 10.0mm per side is
most important.
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
4. Do not let saw dust enter in to the slides.
L1
A
8.0
8.0
L2
M4 x 2 Nos
1.0
27.044.0
32.0
Drawer Depth
Fig.2
±0.210.0
-017
.0
7.5Side Gap
M4
+0.
2
Gro
ove
DRAWER
CABINET
Fig.1
28
Mini Telescopic Drawer Slides H- 36
Special Features
1. Easy to pullout, pull release for disconnect.
2. Ball retainer detent for drawer easy re-install.
3. Hold-in detent.
4. Side space adjustable tabs and non-handed.
5. 32mm hole pattern.
Fitting Instructions
1. Side gap required is 12.7mm (½”) per side (Ref. Fig. 1).
2. Fix the outer (fixed) slides to the cabinet. Access to holes can be got
through slots in intermediate slide (Ref. Fig. 1).
3. Press latch and remove the inner slide (Ref. Fig. 2).
4. Slides should be fitted parallel and screws tightened fully to avoid gaps.
5. Fit inner slide onto the outside of the drawer. (Ref. Fig. 1).
6. Now, slide the drawer with inner slide fitted onto the intermediate slides
on the cabinet.
Caution
1. Side gap required is 12.7mm per side is most important.
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
4. Do not let saw dust enter in to the slides.
±0.3
12.7
DRAWER
CABINET
±0.
336
.0
Specifications
Slide Length mm
Item Code Extension mm
Max. Load Kgs.
Gap/Slide mm
Finish
12.7 25Bright Zinc
Plated
MTDS 35 350 350
MTDS 40 400 400
MTDS 45 450 450
MTDS 50 500 500
Fig.2
Fig.1
29
Basket Slides - 12.7mm
Special Features
! Precision Ball Bearing.
! Full extension of drawer.
! Special clamp arrangement for baskets.
! Basket can be removed by depressing latch.
! Max. Load capacity 35 kg.
Drilling Diagram for Cabinet
400
450
500
550
600
Front Edgeof cabinet
31.0 96.0 64.0 295.0 32.0 32.0 53.0
32.032.0
32.0 32.0
32.0 32.0
64.0145.0
95.0
195.0
245.0
30
Specifications
Fitting Instructions
1. Basket slides require 12.7 to 13 mm gap per side.
(Ref. Fig.1)
2. Inner slide can be removed by depressing latch.
(Ref. Fig.2)
4. Baskets are clamped onto the slides where two
clamps are provided.
Code No. Length(mm)
Extension(mm)
Max. LoadKgs.
Gap/Side(mm)
Finish
KBTS-40 (I) 400 410
KBTS-45 (I) 450 460 12,7
KBTS-50 (I) 500 510 to 35
KBTS-55 (I) 550 560 13.0
KBTS-60 (I) 600 610
WhiteBlack, Zn Plated
12.7
13.0
45.0
Fig. 1
12.7
13.0
Fig. 2
Depress latchto remove tray.
31
Special Features
! Full extension of drawer available.
! Direct front installation without De-assembly.
! Precision ball bearing for smooth movement.
! Hole 'System-32' compatible.
Front Edge of Cabinet
750
35.00 128.00 96.00 96.00 96.00 96.00 64.00 96.00
700
650
600
550
500
450
400
Drilling Diagram for Cabinet
Heavy Duty Telescopic Drawer Slides
Design Reg. No: 162398/90
32
For efficiency and durability.
1. Side gap of 25 mm (1”) per side is most important.
2. Fit slides parallel and at equal height.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
Caution
Zinc Plated
60
50
25.0
Lengthmm
Extensionmm
Gap/Sidemm
Max. LoadKgs.
FinishCode Nos.
HTDS 40 400 412
HTDS 45 450 462
HTDS 50 500 512
HTDS 55 550 562
HTDS 60 600 612
HTDS 65 650 662
HTDS 70 700 712
HTDS 75 750 762
1. To install, gap per side required is 25mm. (Refer fig. 1)
2. Screw holes are accessible through slots in inner slides.
3. Slides must be fitted parallel and at equal height.
4. Screw outer slides on drawer and inside of cabinet
maintaining parallelism.
Fitting Instructions
Fig.1
DRAWER
MinimumBottom Clearance
3.2
1/8”
CABINET
34.0
25.0
SIDE MOUNTING
Specifications
33
! Smooth quiet movement with ball bearings.
! Set comes with left and right hand slides.
! Removable drawer with depressible latch.
! Adjustable height on Mounting Brackets.
! Direct front installation.
! Pressure Latch prevents play.
! Slides can be fitted top hung or bottom hung.
For efficiency and durability.
1. Side gap of 20 mm per side is most important
2. Fix slides parallel and at equal height.
3. Do not apply paint or polish.
4. Do not interchange right and left inner slides.
Special Features
CKDS 35 350 200
CKDS 45 450 250
Code Nos.Length(mm)
Extension(mm)
Gap/Side(mm)
Max.LoadKgs.
Black, Whiteand
zinc plated.
Finish
Specifications
1. Fit Mounting brackets with outer side in 80 mm
from the front edge of the table. ( Ref. Fig.1 )
2. Slides can be fitted top hung or bottom hung.
Caution
MountingBrackets
80.0
Front Edgeof TableFig.1
Fitting InstructionsVariable Height Mounting
Brackets are also reversible.
Key Board TrayAttached to moving slide
New Pressure Latch prevents play &movement of Keyboard when pulled out.
Tray can be completely removed bydepressing Latch.
Fig.2
Depress latchto removetray.
20 35
Fig.3
Hei
ght
Adju
stm
ent
36.0
Computer Keyboard Slides
Design Reg. No: 172578/96
34
Computer Keyboard Slide - Eco
Special Features
! Basic and economic option.
! Having all steel construction with ball cages for long life.
! Has a built in end stop. (Ref. Fig. 1)
Code Nos. CKSE 37
Specifications
Fig.1
42 1.0
Latch
76.0
Special Features
! Basic and economic option.
! Having all steel construction with ball cages for long life.
Specifications :
Code No.
CKSE 35 (I)
CKSE 45 (I)
Slide
Length
mm
350
450
Extension
mm
250
350
Finish
Zinc
Plated
Max. Load
Kgs.
12
Fig. 1
2 4.02
32.0
Fig. 2 Height Adjustment
62.0
Min
. 95.0
Max
.
36.0
Front View
Computer Keyboard Slide - Eco (I)
35
Two Way Slides
! Slim design requires only 10mm side gap.
! Can be used with bigger drawers as slides are reversible.
! No deassembly required.
! "System 32" compatible.
! Precision ball bearing for smooth movement.
! Load capacity - 12kgs.
Code Nos.Length(mm)
Extension Loss (mm)
Drawer Length‘A’ mm
Gap/Side(mm)
10
Max.LoadKgs.
12Zinc
plated.
Finish
TWDS 200-325 194 58.0 200-325
TWDS 300-485 290 88.0 300-485
TWDS 375-625 374 118.0 375-625
TWDS 420-710 418 118.0 420-710
Special Features
Specifications
Front Edge of Cabinet
420
375
300
200
27.00 32.00 64.00 172.00 64.00 32.00
32.00
32.00
32.0076.00
64.00128.00
172.00
Drilling Diagram for Cabinet
36
Minimum BottomClearance
3.2m
m1/
8”
10.0
6.7
13.5
27.0
CABINET
DRAWER
Fig.2
10.0
27.0
Minimum BottomClearance
1/8”CABINET
DRAWER
3.2m
m
Fig.1
CABINET
DRAWER
Minimum Cabinet Depth =
Drawer Length + 1 mm
Drawer Length ‘A’
Extension Loss
Fig.3
1. 10mm side gap required per side. (Refer fig. 1)
2. Can be recessed fitted in a 27mm slot to reduce side gap. (Refer fig. 2)
3. Slide must be parallel and at equal height.
Fitting Instructions
For efficiency and durability.
1. Strictly maintain side gap given in diagrams.
2. Fit slides parallel and at equal heights.
Caution
Quadrail Slides
! This new drawer slide system has a unique design with chrome
steel ball bearings and rollers for long life, smooth working and
two dimensional guiding.
! Easy to fit by just pushing the drawer in and come with a special
Release Clip with built-in Fascia Adjuster.
Special Features
! Has a spring loaded auto-closing feature.
! System 32 compatible
! Saves space due to reduced side gap.
Front Edge of Cabinet
600
550500450
400350300
250
5.00 96.00
160.00160.00
224.00
224.00
288.00
288.00
352.0016.00
16.00
16.00
16.0040.00 32.00 32.00
33.00
Drilling Diagram for Cabinet
Specifications
QSDS 25 255 134 250 265
QSDS 30 305 184 300 315
QSDS 35 355 234 350 365
QSDS 40 405 284 400 415
QSDS 45 455 334 450 465
QSDS 50 505 384 500 515
QSDS 55 555 434 550 565
QSDS 60 605 484 600 615
4.0 30Zinc
plated.
Code Nos. Slide Length(mm)
Extension (mm)
Drawer Length(L) mm
Min Cabinetdepth mm
Gap/Side(mm)
Max.LoadKgs.
Finish
37
38
1. Side wall thickness of drawer should not exceed 16mm Max.
and bottom extension of side should not exceed 10mm max.
(Refer fig. 1).
2. Drill hole Ø6mm required at the rear of drawer to anchor the
rear end of slides (Refer fig. 2).
3. Release clips to be fitted the drawer in front of the fascia.
(Refer fig. 3)
4. Mounting brackets of slide to be fitted parallel and at equal
height inside the cabinet leaving 5mm from the front edge
(Refer fig. 4).
5. Push Drawer onto slide and automatically locks onto the
slides. (Refer fig. 5).
6. Fascia can be adjusted by sliding the adjuster.
Fitting Instructions
DRAWER
Fig.1
7.0
16.0 Max.
Ø6.0CABINET
10.0
Max
.
20.0
11.0
28.5
18.0 20.0
Fig.2
Ø6.0
11.0
10.0
18.0
'L'
Fig.3 BOTTOM VIEW OF DRAWER
13.0 64.0 13.064.0
Fig.4
DRAWER CABINET
5.0
Fig.5
Facia adjuster toadjust the levelof drawer
Press toremove thedrawer
39
Side Hinged Door Slide
SHUTTER WOODSTRIP
CABINET
Fig.2SHUTTER
45.0
12.0
Dee
p
Ø35
.0
10.0
37.0
FRONT VIEW
SLIDE
WOOD STRIP
BRIDGE
SHUTTER
HINGE
CORNERROLLER
CABINET
Fig.1
Specifications
Code Nos.
WhiteZinc
Plated
Length(mm)
Min. Widthof shutter (mm)
Max. weightof shutter (kgs)
Thickness ofshutter (mm)
Finish
SHDS 30 300 175
SHDS 35 350 225
SHDS 40 400 275
SHDS 45 450 325 16 to 19 5.5
SHDS 50 500 375
SHDS 55 550 425
SHDS 60 600 475
Special Features
! Cabinet shutter opens 90° and can slide inside the cabinet on each side.
! Channels are mounted inside the cabinet on the side.
! Precision ball bearings with European type cup hinges.
! Support rollers reduce sag of door.
! L-shaped bridge provided to fit wood strip to prevent jamming.
! Adjustable hinges with auto-closing.
! Corner roller for door protection. Ideal for TV cabinet.
1. Fit the slides onto inside of cabinet as in Fig.1.
2. Slides should be parallel to each other or they will get damaged.
3. Bridges must face each other and a wooden strip must be fixed to join them.
4. Shutter thickness must not be less than 16 mm and not more than 19 mm.
5. To fit Hinge in shutter use Ø35 mm round cutter 12 mm deep. Do not use
chisel. Round cavity should be 10 mm from edge (Refer fig.2).
Fitting Instructions
40
Top Hinged Door Slide
! Shutter opens upwards and slides on top of the cabinet. Ideal for
T.V., Bar and filing cabinets.
! Precision ball bearing movement with roller to protect shutter.
! Special cranked hinge.
Special Features
For efficiency and durability.
1. Fit slides parallel and at equal height.
2. Do not apply paint or polish.
Caution
Specifications
Code Nos.Length(mm)
Min. Height of shutter (mm)
Movementof slide (mm)
Min. thicknessof shutter (mm)
Finish
THDS 30 300 320 175
THDS 35 350 370 225
THDS 40 400 420 275
THDS 45 450 470 325 16
THDS 50 500 520 375
THDS 55 550 570 425
THDS 60 600 620 475
WhiteZinc
Plated
Fig.1
Hinge
SlideSHUTTER
CABINET
10.0
10.0
Fig.3
Recessed Slot in Shutter
35.0
8.6
Fig.4
Top front edge of Cabinet
10.0
50.0
1.6
Fig.2
SHUTTER
2.5
1.6
CABINET1. Slide fits vertically on inside of shutter in closed condition and
hinge on inside top front edge of cabinet. (Refer Fig. 1).
2. When opened upwards to horizontal position, shutter can slide
backwards on top of the cabinet. (Ref. Fig. 2).
3. Slide must be recessed into 35mm wide and 8.6mm deep slots
inside the shutter. (Refer Fig. 3).
4. Hinge must be recessed into the top front edge of cabinet 50mm
wide and 10mm deep. (Refer Fig. 4).
5. Opening angle : 90°.
Fitting Instructions
41
Premium Sleek Telescopic Slides - Auto Close
Special Features
! Full extension
! 30 mm stroke of Auto - Closing
! Pull force 2.5 kg.
! Non-handed Disconnect Release.
! 45 kg / 100 lbs. loading at 18".
! Electro-Zinc plated with clear, yellow or black chromate,
or Cr-Free galvanized steel.
Specifications
300
350
400
450
500
550
600
8.59.0
21.334.3
27.0 128.0 96.0 128.0
Ø.46 Ø6.4
64.0
160.0
21.69.0
front Edge Cabinet
DRILLING DIAGRAM FOR CABINET
Code Nos.Size(mm)
Length(mm)
Extension (mm)
Max. Load(kgs)
P-STDS-30-AC 300 300 305 25
P-STDS-35-AC 350 350 356 35
P-STDS-40-AC 400 400 406 40
P-STDS-45-AC 450 450 457 45
P-STDS-50-AC 500 500 508 45
P-STDS-55-AC 550 550 559 40
P-STDS-60-AC 600 600 610 40
42
Fitting Instructions
1. To install Ball bearing slide, 13.0 to 13.6 mm side gap per side is
required between cabinet and drawer. (Refer Fig. 1)
2. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can be
got through slots in intermediate slide
3. Slides should be fitted parallel and screws tightened fully to avoid gaps.
4. Fit inner slide onto the outside of the drawer.
5. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch will automatically engage.
Caution
For efficiency and durability :
1. Strictly maintain 13.0 to 13.6 mm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
+0.6-0
13.0
Fig. 1
+0.2-0
12.8
±0.
345
.5
30 mm stroke of Auto-Closing
+0.5-0
8.5+0.5-0
35
9
flush
43
300
350
400
450
500
550
600
Front Edge Cabinet DRILLING DIAGRAM FOR CABINET
128.0
80.0
128.0
176.0
21.69.0
8.5
9.0
27.0 128.0 96.0 128.0
21.634.3
Premium Sleek Telescopic Slides - Soft close
Special Features
! 30 mm stroke of Soft - Closing
! Pull force 3.2 - 3.5 kg
! Soft-closing function built in slide, easy for installation.
! Non-handed Disconnect Release.
! 45 kg / 100 lbs. loading at 20".
! Electro-Zinc plated with clear, yellow or black chromate, or Cr-Free galvanized steel.
Specifications
Code Nos.Size(mm)
Length(mm)
Extension (mm)
Extension Loss (mm)
Max. Load(kgs)
P-STDS-30-SC 300 300 238 -62 20
P-STDS-35-SC 350 35 305 -45 25
P-STDS-40-SC 400 400 378 -22 35
P-STDS-45-SC 450 450 430 -20 40
P-STDS-50-SC 500 500 482 -18 45
P-STDS-55-SC 550 550 533 -17 40
P-STDS-60-SC 600 600 584 -16 35
44
Fitting Instructions
1. To install Ball bearing slide, 13.0 to 13.8 mm side gap per side is
required between cabinet and drawer. (Refer Fig. 1)
2. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can be
got through slots in intermediate slide
3. Slides should be fitted parallel and screws tightened fully to avoid gaps.
4. Fit inner slide onto the outside of the drawer.
5. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch will automatically engage.
Caution
For efficiency and durability :
1. Strictly maintain 13.0 to 13.8 mm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
Fig. 1
+0.8-0
13.0
+0.2-0
12.8
±0.
345
.5
30 mm stroke of Soft-Closing
+0.5-0
8.5+0.5-0
35
9
flush
45
Premium Sleek Telescopic Slides - Push Open
Fitting Instructions
1. To install Ball bearing slide, 13.0 to 13.8 mm side gap per side is
required between cabinet and drawer. (Refer Fig. 1)
2. Fit outer (fixed) slide onto the inside of the cabinet, access to holes can be
got through slots in intermediate slide.
3. Slides should be fitted parallel and screws tightened fully to avoid gaps.
4. Fit inner slide onto the outside of the drawer.
5. Now slide the drawer with inner slide fitted on to the intermediate slides
on the cabinet till the latch automatically engages.
Caution
For efficiency and durability :
1. Strictly maintain 13.0 to 13.8 mm side gap.
2. Fit slides parallel and at equal heights.
3. Do not apply paint or polish.
4. Do not let saw dust enter into the slides.
Special Features
! Full extension
! Push-rebound function built in slide, easy for installation.
! Non-handed Disconnect Release.
! 45 kg / 100 lbs. loading at 18".
! Rebound 2" - 5" when drawer is pushed.
! Electro-Zinc plated with clear, yellow or black chromate,
or Cr-Free galvanized steel.
Specifications
Code No.Sizemm
Lengthmm
Extensionmm
Max. Loadkgs
400
450
500
Front Edge Cabinet DRILLING DIAGRAM FOR CABINET
Ø.64
Ø64.
160.0
21.69.0
8.59.0
21.634.3
27.0 128.0 96.0 128.0
P-STDS-40-PO
P-STDS-45-PO
P-STDS-50-PO
400
450
500
400
450
500
406
457
508
40
45
45
46
Fig. 1
+0.8-0
13.0
+0.2-0
12.8
±0.
345
.5
+0.8-0
13.0
+0.8-0
13.0Max. drawer width
PUSH AREA
400
450
500
400
450
500
600
650
700
Sizemm
SlideLength
Max. drawerwidth Suggested
Without Gasket
GAP 3±0.5 mm
PUSH 2 mm
6±0.5 35
flush 9
48.654.6±0.5
Under horizontal installation,drawer will rebound 2"-5"
when pushing
2"-5" For Overlay Drawer
58.0 + t
t
PUSH 2 mm
9.0 + t35
flush 9
2"-5"
Under horizontal installation,drawer will rebound 2"-5"
when pushing
For Inset Drawer
With Gasket (Anti insect)
t= Gaskett= thickness of gasket max. 8mmpressed amount of gasket min. 2.5mm
Side PanelGasket
(Anti insect)
Front Panel of Drawert APUSH
Min
2.5
mm
Top View (View from 'X')
'X'
flush
54.6-A935
47
Premium Quadrail - Auto Close
Special Features
! Full extension
! Suited to wooden drawer.
! With Easy - Release Catch.
! 45 kg / 100 lbs. loading at 18".
! 45mm stroke of Auto-Closing.
! Ball bearing slide offers strong structure and avoids sway
Fitting Instructions
1. Install the slides as per given diagrams.
300
350
400
450
500
550
600
Front Edgeof Cabinet
288247
224128
32+1-0
37
DRILLING DIAGRAM FOR CABINET
+1-0
3732+1-0
4
9 9 9 9
1226±0.
5
Ø6.3
min. internal carcase depthDrawer length
37 32
4
X
10
37 32
Inner Drawer length = Drawer length + XDrawer length
Inner Drawer
22 10
internal drawer width = internal carcase width-41 mm
+10-1
internal carcase width
internal drawer width
max 16
12-1
4
7
28.5
20.520.5
11
±0.
526 ±
0.5
38
Specifications
Code No.Sizemm
NormalRunnerLength
DrawerLength
LoadCapacity
Kgs.
OverTravel
Min. internal cabinetDepth for Standard
Drawer
Overlay Inset
P-CDS-30
P-CDS-35
P-CDS-40
P-CDS-45
P-CDS-50
P-CDS-55
P-CDS-60
300
350
400
450
500
550
600
300
350
400
450
500
550
600
290
340
390
440
490
540
590
25
30
35
40
35
35
30
310
360
410
460
510
560
610
328
378
428
478
528
578
628
10
10
10
10
10
10
10
48
4-sided-drawer
3-sided-drawer
Inset-drawer
25.8 20
14.8 42
8.6
117
Ø6X10 Depth
Height Adju ment= 3.5mm
st
rovides up ard
P
w
ad u ment only
j st
90º
+0-0.5
20.5
max 16
Ø6X107
max
14
1226
±0.
5
28.5
±0.
511
49
Premium Quadrail - Soft Close
Special Features! Full extension
! Suited to wooden drawer.
! With Easy - Release Catch.
! 45 kg / 100 lbs. loading at 18".
! 45mm stroke of Soft Closing.
! Ball bearing slide offers strong structure and avoids sway
Specifications
Fitting Instructions
1. Install the slides as per given diagrams.
300
350
400
450
500
550
600
Front Edgeof Cabinet
288247
224128
32+1-0
37
DRILLING DIAGRAM FOR CABINET
+1-0
3732+1-0
4
9 9 9 9
1226±0.
5
Ø6.3
min. internal carcase depthDrawer length
37 32
4
X
10
37 32
Inner Drawer length = Drawer length + XDrawer length
Inner Drawer
22 10
internal drawer width = internal carcase width-41 mm
+10-1
internal carcase width
internal drawer width
max 16
12-1
4
7
28.5
20.520.5
11
±0.
526 ±
0.5
38
Code No.Sizemm
NormalRunnerLength
DrawerLength
LoadCapacity
Kgs.
OverTravel
Min. internal cabinetDepth for Standard
Drawer
Overlay Inset
P-CDS-30-SC
P-CDS-35-SC
P-CDS-40-SC
P-CDS-45-SC
P-CDS-50-SC
P-CDS-55-SC
P-CDS-60-SC
300
350
400
450
500
550
600
300
350
400
450
500
550
600
290
340
390
440
490
540
590
25
30
35
40
35
35
30
310
360
410
460
510
560
610
328
378
428
478
528
578
628
10
10
10
10
10
10
10
50
4-sided-drawer
3-sided-drawer
Inset-drawer
25.8 20
14.8 42
8.6
117
Ø6X10 Depth
Height Adju ment= 3.5mm
st
rovides up ard
P
w
ad u ment only
j st
90º
+0-0.5
20.5
max 16
Ø6X107
max
14
1226
±0.
5
28.5
±0.
511
51
Premium Quadrail - Push Open
Special Features
! Push-rebound function built in slide, easy for installation
! Full extension
! Suited to wooden drawer.
! With Easy - Release Catch.
! 40 kg / 90 lbs. loading at 18".
! Ball bearing slide offers strong structure and avoids sway
! Fully push in (2 mm) for open or close
Under horizontal installation, drawer will redound 5" - 8"
when pushing
! Cr-free galvanized steel.
Fitting Instructions
1. Install the slides as per given diagrams.
Specifications
Code No.Sizemm
NormalRunnerLength
DrawerLength
+0-1.5
LoadRatingkg/pr
P-CDS-50-PO 500 500 490 35
Min. internal CarcaseDepth for Drawer
510
OverTravel
10
Max.DrawerWidth
700
500
Front Edgeof Cabinet
247
224
12832 37
+1-0
DRILLING DIAGRAM FOR CABINET
+0-0.5
20.5
max 16
max
14
12
7
11
26±
0.5
28.5
±0.
5
610
ØX
52
+1-0
32 37
+1-0
4
9 9 9 9
1226±
0.5
Ø63.
25.8
8.6
20
4214.8
dHeight A justment= +3.5mm
Pro ides upwa d
v
r
ad ustmn only
je t
90º
Ø6X10 Depth117
min. carcase depth GAP 4-5 mm
Drawer length -1.5+0
+0-1
37
PUSH2 mm
Under horizontal installation,drawer will rebound 5" - 8" when pushing 5 - 8"
Internal drawer width=internal carcase -41 mm
+0-1
Internal carcase width
max. drawer width
internal drawer width
PUSH
PUSH