Download - Yamaha Electone DDK7 Service Manual
-
SERVICE MANUAL
HAMAMATSU, JAPAN
SERVICE MANUAL
Copyright (c) Yamaha Corporation. All rights reserved. PDF & 07.03
EL
SPECIFICATIONS .............................................3PANEL LAYOUT ................................................5CIRCUIT BOARD LAYOUT ...............................9DISASSEMBLY PROCEDURE .......................11LSI PIN DESCRIPTION ...................................37IC BLOCK DIAGRAM ......................................46CIRCUIT BOARDS ..........................................49TEST PROGRAM ............................................72ERROR MESSAGES ......................................80TOUCH PANEL CALIBRATION .......................82FLICKER ADJUSTMENT (LCD) ......................84
CONTENTSVERSION UPGRADE......................................85FACTORY SET (INITIALIZING THE DDK-7) ...86INITIALIZING REGISTRATION MEMORY ......86INITIALIZING INTERNET SETTINGS .............87SYSTEM BOOTING FLOWCHART ................88MIDI IMPLEMENTATION CHART ...................90MIDI DATA FORMAT .......................................91PARTS LISTBLOCK DIAGRAMWIRINGOVERALL CIRCUIT DIAGRAM
DDKU-P7 (Pedal unit)DDKU-L7 (Keyboard stand) DDKU-B7 (Bench)DDKU-R7 (Music rest)
001778
-
DDK-7
2
WARNING
WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (Where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
WARNING : Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components and failure of the product to perform as specified. For these reasons, we advise all Yamaha product owners that all service required should be performed by an authorized Yamaha Retailer or the appointed service representative.
IMPORTANT : This presentation or sale of this manual to any individual or firm does not constitute authorization certification, recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division.
WARNING : Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus.)
IMPORTANT : Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the unit.
Components having special characteristics are marked and must be replaced with parts having specifi cation equal to thoseoriginally installed.
Saving and backing up your data Always save data to a USB fl ash memory or other external media, in order to help prevent the loss of important data due to
a malfunction or user operating error.
Backing up the external media To protect against data loss through media damage, we recommend that you save your important data onto two external media.
Be sure toperform it
SAVING DATA
-
3DDK-7
KEYBOARD Keyboard Type UPPER: 49 Keys (C-C) Standard (FS)LOWER: 61Keys (C-C) Standard (FS)
Touch Tone UPPER: Initial Touch/After TouchLOWER: Initial Touch/After Touch
TONE GENERATION AWM2
Maximum Polyphony Voice Sections: 128 notesOrgan/Rhythm Sections, XG: 128 notes
Multi Timbral Capacity 16
Wave Voice Sections: 177MB (when converted to 16-bit linear format)Organ/Rhythm Sections, XG: 166MB (when converted to 16-bit linear format)
Registration Memory 1-16, D. (Disable)
Basic Registration 1-16, Current Registration
Registration Menu 288 Registrations
Voice Preset Voice Preset: 415 Voices + 25 Drum KitsXG (Only for playing): 480 Voices + 11 Drum Kits
User Voice: 16
Voice Sections UPPER: 2, LEAD: 2, LOWER: 2, PEDAL: 2
Voice Buttons SECTION SELECT, VOLUME UP/DOWN,TO LOWER (LEAD1, PEDAL1, 2), SOLO (LEAD2)
Effects Reverb: 29 Types x 2 (Voice/Rhythm), Brilliance, Sustain, Insertion (1, 2) x 183 Types x 8
Organ Flute Voice Organ Sections UPPER, LOWER
Type SINE, VINTAGE
Footage 16, 5 1/3, 8, 4, 2 2/3, 2, 1 3/5, 1 1/3, 1, Attack: 4, 2 2/3, 2, LENGTH, RESPONSE
Mode FIRST, EACH
Organ Effect 15 Type
Control U.ORGAN FLUTES, L.ORGAN FLUTES, ROTARY SP SPEED
Rhythm Rhythm Preset: 274 Pattern x 7 parts x 15 SectionsUser Rhythm: 48 Pattern x 7 parts x 15 Sections
Rhythm Buttons SECTION SELECT, VOLUME UP/DOWN
Parts Main Drum, Add Drum, Chord 1, Chord 2, Pad, Phrase1, Phrase 2
Rhythm Control INTRO 1,2,3, ENDING 1,2,3, MAIN A,B,C,D, FILL IN A,B,C,D, BREAK
Tempo 40 - 240
Keyboard Percussion Preset: 2, User: 8
SubordinatePerformance
Auto Bass Chord 3 Type, Memory (LOWER, PEDAL)
Melody On Chord 3 Type, Memory (LOWER, PEDAL)
PROGRAMS Voice Edit Layers AWM (4)
Parameter Element ON/OFF, EQ Low Frequency, EQ Low Gain, EQ High Frequency, EQ High Gain, Level, Note Limit, Pan, Note Shift, Tune Fine, Attack Rate, ReleaseRate, Cutoff Frequency, Resonance, LFO waveform, LFO Speed, LFO Pitch
Modulation Depth, LFO Frequency Modulation Depth, LFO Amplitude Modulation Depth
Rhythm Pattern Program
Sections INTRO 1, 2, 3, ENDING 1, 2, 3, MAIN A, B, C, D, FILL IN A, B, C, D, BREAK
Note Resolution 480 ppq (parts per quarter note)
Beat 2/4, 3/4, 4/4, 5/4
Measure 32
Kits 20 Drum Kits + 5 SFX Kits
Accompaniment Chord1, 2
Voice 480 Voices
Effects Reverb: 29 Types, Chorus:15 Types, Variations: 183 Type
Percussion InstrumentSetting
Pan, Volume, Reverb, Pitch Coarse/Fine
SPECIFICATIONS
-
DDK-7
4
Rhythm Sequence Program
Sequence 140 measures x 4 Sequences
RegistrationSequence Program
Sequence 140 Registration x 4 Sequence, Next Registration
Set Resolution 96 ppq (parts per quarter note)
Keyboard Percussion Assign
Kits 16 Drum Kits
Drum Setup Pan, Volume, Reverb, Pitch Coarse/Fine
Registration Shift Steps 80 Steps
Shift End Stop, Top, Next Regist
Unifying parameter Parameters Reverb (Voice/Rhythm), Volume, Pan, Brilliance, Sustain
FolderM.D .R . Up to 100 folders can exist in one media.
Song Up to 100 songs can exist in one folder.
Registration Up to 50 Registrations can exist in one song.
Recording UPPER, LOWER, PEDAL, CONTROL, LEAD, K.B.P.
Playing UPPER, LOWER, PEDAL, CONTROL, LEAD, K.B.P., XG
Sequence Format DDK Original format (Copy Protect), SMF format 0, 1 (Format 1 load only)
Format Conversion Convert TO EL, Convert FROM EL, Convert to XG
CONTROLS Display Control VOICE DISPLAY, REGIST MENU, FOOT SWITCH, MDR, INTERNET, UTILITY,PROGRAM, SUSTAIN, REVERB
Foot Pedal Section 1 (Expression), 2 (Sustain)
Select Expression, Sustain, Rhythm, Glide, Rotary speaker, Slide, M.O.C.
FootSwitch (When DDKU-P7 is used)
Left Rhythm, Glide, Rotary speaker
Right Shift, Jump, User
OTHERS LCD Display Size 6.5-inch 144 (W) x 78.24 (H) mm
Liquid Crystal Display TFT (WVGA) + touch panel
Drive Method Active Matrix
Dots 800 x RGB x 480 dots
Connectors PHONES, MIC, MIC VOLUME, OUTPUT L/L+R, R (Phone), AUX OUT (LEVEL
Output Impedance HEADPHONE : 68 OUTPUT MAIN L/L+R, R : 600 AUX OUTPUT MAIN L/L+R, R : 600 AUX OUTPUT SUB L/L+R, R : 600
FIXED) MAIN L/L+R, R, SUB 1,2 (Phone), AUX IN L/L+R, R (Phone), TO PEDAL,OPTICAL OUT, USB TO DEVICE x 2, USB TO HOST, MIDI IN/OUT, FOOT
PEDAL 1 (VOLUME), 2 (SUSTAIN), AC INLET
Power Consumption 51 W
Dimensions (W x D x H), Weight 1,150 (W) x 424 (D) x 173 (H) mm, 18 kg
Supplied Accessories Owners Manual, AC Power cord
-
5DDK-7
/
4
) 0 1 6 2 * -
Front Panel
PHONES jack
MIC jack
FOOT PEDAL jacksUSB/MIDI terminalsTO PEDAL connectorI/O connectors
AC INLET jack
Upper keyboard
USB TO DEVICE terminal
Lower keyboard
PANEL LAYOUT
q LCD display (touch-panel)w DATA CONTROL diale [VOICE DISPLAY] buttonr [REGIST MENU] buttont [FOOT SWITCH] buttony [MDR] buttonu [INTERNET] button
LCD Display/Display Select
Overview
i [UTILITY] buttono [PROGRAM] button!0 [SUSTAIN] button!1 [REVERB] button!2 [U. ORGAN FLUTES] button!3 [L. ORGAN FLUTES] button!4 [ROTARY SP SPEED] button
-
DDK-7
6
13 14 15 16 1 2 3 4 5
UPPER1, 2
LOWER1, 2
Registration memory[M.] (Memory) button
REGIST MENU
SUSTAIN button
RHYTHM/KEYBOARD PERCUSSION
USB TO DEVICE terminal
REVERB button
LCD display/DISPLAY SELECTLEAD 1, 2
PEDAL1, 2
A
A
Front Panel
-
7DDK-7
6 7 8 9 10 12 D.112 3 4 5
ry [D.] (Disable) button
POWER switch
MASTER VOLUME dial
A
A
-
DDK-7
8
1 /
0)4
6 6 * * -2 -1 -1 -2 -1 -2
6 2 * -
q AC INLET jackw PHONES jackse MIC jackr MIC VOLUME knobt USB TO DEVICE terminal
y FOOT PEDAL jacks y-1 1 (VOLUME) jack y-2 2 (SUSTAIN) jacku MIDI IN/OUT terminalsi USB terminals i-1 USB TO HOST terminal i-2 USB TO DEVICE terminal
o OPTICAL OUT terminal!0 TO PEDAL terminal!1 AUX IN (Phone; L/L+R, R) jacks!2 AUX OUT (LEVEL FIXED) jacks !2-1 SUB (1, 2) jacks !2-2 MAIN (L/L+R, R) jacks!3 OUTPUT (L/L+R, R) jacks
-
9DDK-7
HOST
PN
DM2TG2A
Upper Case Unit
Lower Case Unit
U Assy Upper Front Rail Assembly
CP ENC
Y65-VGA MVR
(Upper)
(Lower)
(Upper)
(Lower)
(TG2)
TG1-E2TG1-E1
DAC2A
HP
PRM-DMTAMB HUB Power supply unit
PS1 PS2
CIRCUIT BOARD LAYOUT
-
DDK-7
10
EMKS-FC EMKS-FD
FSX U FSX Keyboard Assembly U
DDKU-P7
FSX D FSX Keyboard Assembly D
MK49L
PK-L PK-H
DJKAJK
MKH-C MK61L MKH-D
EXP Pedal (2CH)EXP Pedal (2ND)(EXP (2CH))(EXP (2ND))
EXP(2ND) (2CH)
EXP
Lower Case Unit
-
11
DDK-7
Disassembly of DDK-7DDK-7 1. Upper Case Unit ...................122. PN Circuit BoardPN ...............................133. HOST Circuit BoardHOST .....................134. ENC Circuit BoardENC ..........................145. Y65-VGAY65-VGA ..............................................146. LCD ........................................157. CP Circuit BoardCP ...............................158. Power Switch ...............................169. UK UnitUK ...........................................1610. Upper Front Rail Assembly, PS1 Circuit Board, PS2 Circuit Board U Ass'yPS1 PS2 .............1611. MVR Circuit BoardMVR .........................1712. TA Circuit BoardTA ................................1713. HP Circuit BoardHP ...............................1714. DM2 Circuit Board, TG2A (TG2) Circuit Board DM2TG2A (TG2) ........................1815. TG1-E1 Circuit BoardTG1-E1 ................1816. DAC2A Circuit Board, HUB Circuit Board DAC2A HUB ...............................1917. DM BoxDM ..........................................1918. TG1-E2 Circuit BoardTG1-E2 ................2019. MB Circuit BoardMB .............................2020. AJK Circuit Board, DJK Circuit Board AJKDJK .....................................2121. Power Supply Unit, PRM-DM Circuit Board PRMDM ..........................21
22. AC InletAC .......................................2223. LK UnitLK ............................................2224. Keys (White and Black Keys) ...............................................2425. Installing Keys (Black and White Keys) ............................2426. Rubber Contact ...................................2627. MK49L Circuit Board, MKH-C Circuit Board MK49L MKH-C ...........................2728. MK61L Circuit Board, MKH-D Circuit Board MK61L MKH-D ...........................29
Disassembly of DDKU-P7DDKU-P7 29. EXP Pedal (2CH) and EXP (2CH) Circuit Board EXP2CHEXP (2CH) ..............3130. EXP Pedal (2ND) and EXP (2ND) Circuit Board EXP2NDEXP (2ND) ..............3131. Pedal Keyboard Assembly Ass'y ...3232. Handle Set ................................3433. Disassembling Pedal Keyboard Assembly (PK-L Circuit Board, PK-H Circuit Board, White Keys, Black Keys) Ass'y PK-L PK-H ......................................3434. PK CoverPK ...........................................35
DISASSEMBLY PROCEDURE
Lay a cloth such as servicing cloth 700 x 1600 mm (AAX62080) and place theunit on the cloth during disassembly.Be sure to attach the removed filament tapes just as it was before removal.Pay attention not to insert and install the cable to the connector inversely. (Photo A)
700 x 1600mm (AAX62080) A
Precautions
Photo A ( A)
Front side (Printed side)
Back side
-
DDK-7
12
[S11B]
[S14A]
[S11A] [S11A][S14A]
[S12]
[S14A][S14A]
[S14A]
[S14A]
[S14A]Lower case unit
Lower case unit
Disassembly of DDK-7
1. Upper Case Unit (Time required: About 3 minutes)1-1 Turn the DDK-7 upside down and remove the
fi fteen (15) screws marked [S14A], four (4) screws marked [S11A] and the screw marked [S12]. (Fig. 1)
1-2 Face the upper side of the DDK-7 upward. Now that the screws are removed, the upper case unit is not fixed. Pay attention not to drop any part when turning back the DDK-7.
1-3 Place a table behind the DDK-7 so that the upper case unit can be put on it after the upper case unit is removed in the following procedure. Lay a cloth on the table. (Photo 1)
1-4 Lift the upper case unit a little and slide it toward the front side. (Photo 1)
* The front part of the upper case unit has low strength and should not be held during the procedure.
* To prevent surfaces from being scratched, pre-pare a cloth such as servicing cloth 700 x 1600 mm (AAX62080).
DDK-7
1. 31-1 [S14A]15 [S11A]
4[S12] 1 11-2
1-3
11-4
1
700 x 1600mm
(AAX62080)
[S11]: Bind Head Screw BIND4.0X10 MFZN2W3 (WE966500)[S12]: Bind Head Screw BIND4.0X10 MFZN2B3 (WE980400)[S14]: Bind Head Tapping Screw-BB BIND4.0X16 MFZN2W3 (WF154100)
Fig. 1 ( 1)
-
13
DDK-7
Upper case unit A table with a cloth on it
Upper case unit
2. PN Circuit Board (Time required: About 6 minutes)2-1 Remove the upper case unit. (See procedure 1)2-2 Remove the six (6) screws marked [S02A]. The
insulation cover can then be removed. (Fig. 2)2-3 Remove the twelve (12) screws marked [S02B].
The PN circuit board can then be removed. (Fig. 3)
3. HOST Circuit Board (Time required: About 4 minutes)3-1 Remove the upper case unit. (See procedure 1)3-2 Remove the three (3) screws marked [S02C]. The
HOST circuit board can then be removed. (Fig. 2)
2. PN 62-1 12-2 [S02A] 6
22-3 [S02B] 12 PN
3
3. HOST 43-1 1 3-2 [S02C] 3HOST
2
Photo 1 ( 1)
[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)
Fig. 2 ( 2)
[S02C]
[S02D]
[S02D][S02E]
[S02C][S02A]
[S02A]
[S02A]HOST
[S02E]
ENC AssemblyENC Assy
LCD Cover assemblyLCDAssy
Insulation cover
Upper Case Unit
-
DDK-7
14
PN
[S13A]
[S13A]
[S02B]
Data line filter
Data line filter
[S02B]
[S02B]
Upper Case Unit Encoder knob
()
ENC Assy ENC Assembly
ENC
ENC HolderENC
NutA
4. ENC Circuit Board (Time required: About 4 minutes)4-1 Remove the encoder knob. (Fig. 4)4-2 Remove the upper case unit. (See procedure 1)4-3 Remove the three (3) screws marked [S02D]. The
ENC assembly can then be removed. (Fig. 2)4-4 Remove the nut marked [A]. The ENC circuit
board can then be removed. (Fig. 5)
5. Y65-VGA (Time required: About 5 minutes)5-1 Remove the upper case unit. (See procedure 1)5-2 Remove the four (4) screws marked [S02E]. The
LCD cover assembly can then be removed. (Fig. 2)5-3 Remove the six (6) screws marked [15e]. The
Y65-VGA can then be removed. (Fig. 6)
4. ENC 44-1 44-2 14-3 [S02D] 3ENC Ass'y
24-4 [A] ENC 5
5. Y65-VGA 55-1 15-2 [S02E] 4LCD Ass'y
25-3 [15e] 6Y65-VGA
6
[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[S13]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 3 ( 3)
Fig. 4 ( 4)
Fig. 5 ( 5)
-
15
DDK-7
Y65-VGA
LCD Assy LCD Assembly
LCD HolderLCD+
[15e] [15e]
[15d][15d]
LCD
[S04A][S04E] [S04A]
[S04B]
[S04C]
[S04C]
[S04B]
[US02] [US02]
CP Panel holder LL
UK UnitUK [S04E]
[S04D] [S04D]
Upper Case Unit
Power switch
[S02F] [S02F]
Upper front rail assemblyU Assy
6. LCD (Time required: About 6 minutes)6-1 Remove the upper case unit. (See procedure 1)6-2 Remove the LCD cover assembly. (See procedure 5-2)6-3 Remove the two (2) screws marked [S13A]. The
LCD assembly can then be removed. (Fig. 3)6-4 Remove the four (4) screws marked [15d]. The
LCD can then be removed. (Fig. 6)* After replacing the LCD, calibrate the touch
panel. (See page 82.)
7. CP Circuit Board (Time required: About 7 minutes)7-1 Remove the upper case unit. (See procedure 1)7-2 Remove the LCD cover assembly. (See procedure 5-2)7-3 Remove the LCD assembly. (See procedure 6-3)
6. 66-1 16-2 LCD Ass'y 5-2 6-3 [S13A] 2LCD Ass'y
36-4 [15d] 4
6
7. CP 77-1 17-2 LCD Assy 5-2 7-3 LCD Assy 6-3
[15d]: Bind Head Tapping Screw-BB BIND2.6X6 MFZN2W3 (WE985800)[15e]: Bind Head Tapping Screw-BB BIND3.0X6 MFZN2W3 (WE936300)
Fig. 6 ( 6)
[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[S04]: Bind Head Tapping Screw-BB BIND3.0X10 MFZN2W3 (WE774200)[US02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)
Fig. 7 ( 7)
-
DDK-7
16
UK UK Unit
U Assy Upper Front Rail Assembly
[U3fA]
Upper front rail assemblyU Assy
Cord holder
PS1 PS2
[U3fA] [U3fB] [U3fB]
Cord holder
Cord holder
7-4 Remove the two (2) screws marked [S04A] and four (4) screws marked [S04B]. The two (2) panel holder Ls can then be removed. (Fig. 7)
7-5 Remove the six (6) screws marked [S04C]. The CP circuit board can then be removed. (Fig. 7)
8. Power Switch (Time required: About 4 minutes)8-1 Remove the upper case unit. (See procedure 1)8-2 Remove the two (2) screws marked [S02F]. The
power switch can then be removed.(Fig. 7)
9. UK Unit (Time required: About 6 minutes)9-1 Remove the upper case unit. (See procedure 1)9-2 Remove the four (4) screws marked [S04D] and
four (4) screws marked [US02]. The UK unit can then be removed. (Fig. 7)
10. Upper Front Rail Assembly, PS1 Circuit Board, PS2 Circuit Board
(Time required: About 7 minutes each)10-1 Remove the UK unit. (See procedure 9)10-2 Remove the two (2) screws marked [S04A] and
fi ve (5) screws marked [S04E]. The upper front rail assembly can then be removed. (Fig. 7)
10-3 PS1 Circuit Board10-3-1 Remove the fi ve (5) screws marked [U3fA] and cut
the fi ve (5) cord holders on the PS1 circuit board side. The PS1 circuit board can then be removed. (Fig. 8)
7-4 [S04A] 2 [S04B] 4 L 2 7
7-5 [S04C]6CP 7
8. 48-1 18-2 [S02F] 2
7
9. UK 69-1 19-2 [S04D] 4 [US02] 4
UK 7
10. Ass'yPS1 PS2 710-1 UK 910-2 [S04A] 2 [S04E] 5
U Ass'y 710-3 PS1 10-3-1 [U3fA]5PS1
5PS1 8
[U3f]: Bind Head Tapping Screw-BB BIND3.0X6 MFZN2W3 (WE936300)
Fig. 8 ( 8)
-
17
DDK-7
Upper case
MVR AssemblyMVR Assy
[S02G]
VR Knob[B] VR
Nut
MVR
10-4 PS2 Circuit Board10-4-1 Remove the fi ve (5) screws marked [U3fB] and cut
the three (3) cord holders on the PS2 circuit board side. The PS2 circuit board can then be removed. (Fig. 8)
11. MVR Circuit Board (Time required: About 6 minutes)11-1 Remove the upper case unit. (See procedure 1)11-2 Remove the UK unit. (See procedure 9)11-3 Remove the four (4) screws marked [S02G]. The
MVR assembly can then be removed. (Fig. 9)11-4 Remove the VR knob from the MVR assembly.
(Photo 2)11-5 Remove the nut marked [B]. The MVR circuit
board can then be removed. (Photo 2)
12. TA Circuit Board (Time required: About 4 minutes)12-1 Remove the upper case unit. (See procedure 1)12-2 Remove the four (4) screws marked [S02H]. The
TA circuit board can then be removed. (Fig. 10)
13. HP Circuit Board (Time required: About 4 minutes)13-1 Remove the upper case unit. (See procedure 1)13-2 Remove the four (4) screws marked [S02I]. The
HP circuit board can then be removed. (Fig. 10)13-3 Remove the knob from the HP circuit board. (Photo 3)* The knob is not a component of the HP circuit
board. When replacing the HP circuit board, remove the knob from the HP circuit board and install it to the new HP circuit board.
10-4 PS2 10-4-1 [U3fB]5PS2
3PS2 8
11. MVR 611-1 111-2 UK 911-3 [S02G] 4MVR Ass'y
911-4 MVR Ass'y VR 211-5 [B] 1MVR
2
12. TA 412-1 112-2 [S02H] 4 TA
10
13. HP 413-1 113-2 [S02I]4HP
10 13-3 HP 3 HP
HPHPHP
[S02]: Bind Head Tapping Screw-BB BIND 3.0X8 MFZN2W3 (WE774300)
Fig. 9 ( 9)
Photo 2 ( 2)
-
DDK-7
18
Lower Case Unit
[S02M][S02H][S01A] [S02M]AC Cover
AC
DML CoverDML
Data line filter
Data line filter
DMC CoverDMC
DMR CoverDMR
AC-DM-UK Angle bracketACDMUK
[S11C]
[S01B][S01C]
[S01D] [S13B]
[S01A]
[S01B] [S02J] [S02J][S02I] [S01D][S01D]
TA
HP [S07][S02I]Data line filter
Knob
HP Circuit board
HP
14. DM2 Circuit Board, TG2A (TG2) Circuit Board14-1 Remove the upper case unit. (See procedure 1)14-2 Remove the seven (7) screws marked [S01A]. The
DML cover can then be removed. (Fig. 10)14-3 DM2 Circuit Board (Time required: About 5 minutes)14-3-1 Remove the five (5) screws marked [8pA]. The
DM2 circuit board can then be pulled out forward. (Fig. 11)
14-4 TG2A (TG2) Circuit Board (Time required: About 6 minutes)14-4-1 Remove the three (3) screws marked [8qA]. The
TG2A (TG2) circuit board can then be pulled out forward. (Fig. 11)
15. TG1-E1 Circuit Board (Time required: About 5 minutes)15-1 Remove the upper case unit. (See procedure 1)15-2 Remove the DML cover. (See procedure 14-2) 15-3 Remove the four (4) screws marked [S01B] and
the screw marked [S01C]. The DMC cover can then be removed. (Fig. 10)
15-4 Remove the two (2) screws marked [8pB]. The TG1-E1 circuit board can then be pulled out for-ward. (Fig. 11)
14. DM2 TG2A (TG2) 14-1 114-2 [S01A] 7 DML
1014-3 DM2 514-3-1 [8pA] 5DM2
1114-4 TG2A (TG2) 614-4-1 [8qA] 3 TG2A (TG2)
11
15. TG1-E1 515-1 115-2 DML 14-2 15-3 [S01B] 4 [S01C] 1
DMC 1015-4 [8pB] 2TG1-E1
11
[S01]: Bind Head Screw BIND3.0X6 MFZN2W3 (WE774000)[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[S07]: PW Head Tapping Screw-BB PWH3.0X12 MFZN2W3 (WF002100)[S11]: Bind Head Screw BIND4.0X10 MFZN2W3 (WE966500)[S13]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 10 ( 10)
Photo 3 ( 3)
-
19
DDK-7
Upper level
DM Lower level
DM Box
[8pA] [8pB][8qB] [8qF]
[8qF][8qF][8qC]
[8qB]
[8qD][8qD] [8qD]
DM2
DM2
MB
TG1-E1
TG1-E1
TG2A
TG2A(TG2)
(TG2)
MB
TG1-E2
TG1-E2
DAC2A
DAC2A
HUB
HUB
[8qE]
[8qG]
[8qA][8qD] DMF CoverDMF
DMB CoverDMB
DMB CoverDMB
TG1 HolderTG1
[8qG]
MB
16. DAC2A Circuit Board, HUB Circuit Board (Time required: About 5 minutes each)16-1 Remove the upper case unit. (See procedure 1)16-2 Remove the screw marked [S01C] and six (6)
screws marked [S01D]. The DMR cover can then be removed. (Fig. 10)
16-3 DAC2A Circuit Board16-3-1 Remove the four (4) screws marked [8qB]. The
DAC2A circuit board can then be removed. (Fig. 11)16-4 HUB Circuit Board16-4-1 Remove the three (3) screws marked [8qC]. The
HUB circuit board can then be removed. (Fig. 11)
17. DM Box (Time required: About 5 minutes)17-1 Turn the DDK-7 upside down and remove the two
(2) screws marked [S11B]. (Fig. 1)17-2 Remove the upper case unit. (See procedure 1)17-3 Remove the DML cover. (See procedure 14-2)17-4 Remove the two (2) screws marked [S02J]. The
AC-DM-UK angle bracket can then be removed. (Fig. 10)
17-5 Remove the screw marked [S07], the screw marked [S11C] and the screw marked [S13B]. The three (3) data line fi lters can then be removed. (Fig. 10)
16. DAC2A HUB 516-1 116-2 [S01C] 1 [S01D] 6
DMR 10 16-3 DAC2A 16-3-1 [8qB] 4DAC2A
1116-4 HUB16-4-1 [8qC] 3HUB
11
17. DM 517-1 [S11B] 2
117-2 117-3 DML 14-2 17-4 [S02J] 2 ACDMUK
1017-5 [S07] 1 [S11C] 1[S13B]
1 3 10
[8p]: Bind Head Screw BIND3.0X6 MFZN2W3 (WE774000)[8q]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)
Fig. 11 ( 11)
-
DDK-7
20
17-6 [S13C] 7DM 12
DML DMCDMRDM
18. TG1-E2 1018-1 DM17 18-2 DML 14-2 18-3 DMR16-2 18-4 DMC15-3 18-5 TG1-E1 15-4 18-6 [8qD] 6 DMF TG1
1118-7 [8qE] 2TG1-E2
11
19. MB 1419-1 DM17 19-2 DM2 TG2A (TG2) 14 19-3 TG1-E1 15 19-4 TG1-E2 18 19-5 [8qF] 6DMB
1119-6 [8qG]8MB
11
Lower Case Unit
[S13C] [S13C]DM BoxDM
17-6 Remove the seven (7) screws marked [S13C]. The DM box can then be removed. (Fig. 12)
* The DML cover, DMC cover, DMR cover and the screws for the covers are not components of the DM box.
18. TG1-E2 Circuit Board (Time required: About 10 minutes)18-1 Remove the DM box. (See procedure 17)18-2 Remove the DML cover. (See procedure 14-2)18-3 Remove the DMR cover. (See procedure 16-2)18-4 Remove the DMC cover. (See procedure 15-3)18-5 Remove the TG1-E1 circuit board. (See procedure 15-4)18-6 Remove the six (6) screws marked [8qD]. The
DMF cover and TG1 holder can then be removed. (Fig. 11)
18-7 Remove the two (2) screws marked [8qE]. The TG1-E2 circuit board can then be removed. (Fig. 11)
19. MB Circuit Board (Time required: About 14 minutes)19-1 Remove the DM box. (See procedure 17)19-2 Remove the DM2 circuit board and TG2A (TG2)
circuit board. (See procedure 14)19-3 Remove the TG1-E1 circuit board. (See procedure 15)19-4 Remove the TG1-E2 circuit board. (See procedure 18)19-5 Remove the six (6) screws marked [8qF]. The
DMB cover can then be removed. (Fig. 11)19-6 Remove the eight (8) screws marked [8qG]. The
MB circuit board can then be removed. (Fig. 11)
[S13]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)Fig. 12 ( 12)
-
21
DDK-7
20. AJK DJK 720-1 AJK [S03A] 4
DJK [S03B] 5 13
20-2 DM17 20-3 AJK 20-3-1 [S02K] 3AJK
1320-4 DJK 20-4-1 [S02L] 3DJK
13
21. PRMDM 521-1 121-2 [S02M] 5AC
1021-3 21-3-1 [7fA] 6
1321-4 PRMDM21-4-1 [7fB] 4PRMDM
13
AJK DJK
Power supply unit
Lower Case Unit
[S02K] [S02L] [7fA] [7fA]
[7h][7fC]
[S03B]
[7fB]
PRM-DM
AJKDJK
Data line filter
AC-LF Connector assemblyAC-LF
[S03C] [S03A]
20. AJK Circuit Board, DJK Circuit Board (Time required: About 7 minutes each)20-1 Remove the four (4) screws marked [S03A] to re-
move the AJK circuit board, or remove the fi ve (5) screws marked [S03B] in advance to remove the DJK circuit board. (Fig. 13)
20-2 Remove the DM box. (See procedure 17)20-3 AJK Circuit Board20-3-1 Remove the three (3) screws marked [S02K]. The
AJK circuit board can then be removed. (Fig. 13)20-4 DJK Circuit Board20-4-1 Remove the three (3) screws marked [S02L]. The
DJK circuit board can then be removed. (Fig. 13)
21. Power Supply Unit, PRM-DM Circuit Board (Time required: About 5 minutes each)21-1 Remove the upper case unit. (See procedure 1)21-2 Remove the fi ve (5) screws marked [S02M]. The
AC cover can then be removed. (Fig. 10)21-3 Power Supply Unit21-3-1 Remove the six (6) screws marked [7fA]. The
power supply unit can then be removed. (Fig. 13)21-4 PRM-DM Circuit Board21-4-1 Remove the four (4) screws marked [7fB]. The
PRM-DM circuit board can then be removed. (Fig. 13)
[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[S03]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2B3 (WE774400)[7f]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[7h]: Bind Head Screw BIND4.0X10 MFZN2W3 (WE966500)
Fig. 13 ( 13)
-
DDK-7
22
22. AC 522-1 [S03C] 3
1322-2 122-3 AC 21-2 22-4 [7h] 1
1322-5 [7fC]1AC-LF
13 4 AC-LF AC
AC ACACACAC 4
23. LK 523-1 [S14B] 8
1423-2 123-3 [S07] 1
1023-4 [S04F] 7 [S02N] 1
LK 15
AC-LF AC-LF Connector Assembly
AC Inlet plateAC
Claw
AC InletAC
Data line filter
22. AC Inlet (Time required: About 5 minutes)22-1 Remove the three (3) screws marked [S03C] in ad-
vance. (Fig. 13)22-2 Remove the upper case unit. (See procedure 1)22-3 Remove the AC cover. (See procedure 21-2)22-4 Remove the screw marked [7h]. The data line filter
can then be removed. (Fig. 13)22-5 Remove the screw marked [7fC]. The AC-LF connec-
tor assembly can then be removed. (Fig. 13, Photo 4)* When removing the AC-LF connector assembly,
tilt the AC inlet plate to the front side and pull the AC-LF connector assembly upward.
* The AC inlet plate and data line fi lter are not com-ponents of the AC inlet. When replacing the AC inlet, remove the AC inlet plate and data line fi lter and install them to the new AC inlet. (Photo 4)
23. LK Unit (Time required: About 5 minutes)23-1 Turn the DDK-7 upside down and remove the
eight (8) screws marked [S14B]. (Fig. 14)23-2 Remove the upper case unit. (See procedure 1)23-3 Remove the screw marked [S07]. The data line fi lter
can then be removed. (Fig. 10)23-4 Remove the seven (7) screws marked [S04F] and
the screw marked [S02N]. The LK unit can then be removed. (Fig. 15)
Photo 4 ( 4)
-
23
DDK-7
[S14B]Lower case unit
[S14B]
[S14]: Bind Head Tapping Screw-BB BIND4.0X16 MFZN2W3 (WF154100)
Fig. 14 ( 14)
Lower Case Unit
LK UnitLK
[S04F] [S04F] [S04F]
[S04F]
[S02N]
[S02]: Bind Head Tapping Screw-BB BIND3.0X8 MFZN2W3 (WE774300)[S04]: Bind Head Tapping Screw-BB BIND3.0X10 MFZN2W3 (WE774200)
Fig. 15 ( 15)
-
DDK-7
24
Key Guide Cap
Key Spring
24. Keys (White and Black Keys)24-1 Remove the upper case unit. (See procedure 1)24-2 Remove the UK unit if replacing the keys on the
FSX keyboard assembly U. (See procedure 9)24-3 Remove the four (4) screws marked [S01E] and
remove the two (2) panel stopper assemblies if replacing the keys on the FSX keyboard assembly U. (Fig. 16)
24-4 Remove the key stoppers corresponding to the keys to be replaced. (Table 1, Fig. 16)
24-5 White key24-5-1 Place the white key in the horizontal position and
remove it, lifting while pushing rearward. (Photo 5)* At this time, a key guide cap may come off to-
gether. (Photo 7)24-6 Black key24-6-1 Remove the white keys on the right and left sides
of the black key to be removed. (Photo 5)24-6-2 Place the black key in the horizontal position and
remove it, lifting while pushing rearward. (Photo 6)
25. Installing Keys (White and Black Keys)25-1 Black key25-1-1 With the white keys to the right and left sides re-
moved, lower the front end of the horizontal black key and fi t it into the frame while pushing it down and rearward.
* At this time, pay attention not to bend the key guide cap by lowering the front portion of the key too much. (Photo 7)
25-2 White key25-2-1 After installing the black keys, install the white
keys in the same way as the black keys. (See procedure 25-1)25-3 Install the removed key stoppers. (Table 1, Fig. 16)
24. 24-1 124-2 FSX UUK
924-3 FSX U[S01E]
4 Ass'y 2 16
24-4 1 16
24-5 24-5-1
5
724-6 24-6-1 524-6-2
6
25. 25-1 25-1-1
7
25-2 25-2-1
25-1 25-3 1 16
Photo 5 ( 5)
Photo 6 ( 6)
Photo 7 ( 7)
-
25
DDK-7
Key Stopper L L
Key Stopper H H
Key Stopper 61 61
[240A] [240B] [240C] [240C] [240D] [240D]
Rubber Contact 13 Key B 13Key B
(C1-C2)
Rubber Contact 12 Key E 12Key E
(C#3-C4)
Rubber Contact 12 Key G 12Key G
(C#5-C6)Rubber Contact 12 Key D 12Key D
(C#2-C3)
Rubber Contact 12 Key F 12Key F
(C#4-C5)
C1 C2 C3 C4 C5 C6
MK61L MKH-D
C#2 C#3 C#4 C#5
LK LK Unit
MK49L MKH-C
LKey stopper L
HKey stopper H
Rubber Contact 13 Key A 13Key A
(C2-C3)
Rubber Contact 12 Key B 12Key B
(C#4-C5)Rubber Contact 12 Key A 12Key A
(C#3-C4)
Rubber Contact 12 Key C 12Key C
(C#5-C6)
C2 C3 C4 C5 C6
C#3 C#4 C#5
AssyPanel stopper assembly
AssyPanel stopper assembly
[240A] [240C][240B] [S01E] [S01E][S01E] [S01E]
UK UK Unit
Key Stopper L L
Key Stopper HH
Key Stopper 61 (FSX Keyboard Assembly D only) 61FSX D
Remove Screw [240A] X 2, [240B] X 1 [240B] X 1, [240C] X 2 [240D] X 2
Table 1 1
Fig. 16 ( 16)
[S01]: Bind Head Screw BIND3.0X6 MFZN2W3 (WE774000)[240]: Bind Head Tapping Screw-PP BIND3.0X16 MFZN2B3 (WE983200)
-
DDK-7
26
FSX Keyboard Assembly DFSX D
Rubber contact13Key
13Key B
Rubber contact12Key A
12Key D
Rubber contact12Key B
12Key E
Rubber contact12Key C
12Key F
Rubber contact12Key D
12Key G
Application Circuit Board MK61L MK61L MK61L MKH-D MKH-D
Remove Key Stopper L L, H L, H H 61
Remove Key C1-C2 C2-C3 C3-C4 C4-C5 C5-C6
Table 2 2
Rubber Contact Contact (Long) Contact (Short)
Rubber Contact
FSX Keyboard Assembly UFSX U
Rubber contact13Key
13Key A
Rubber contact12Key A
12Key A
Rubber contact12Key B
12Key B
Rubber contact12Key D
12Key C
Application Circuit Board MK49L MK49L MKH-C MKH-C
Remove Key Stopper L L, H L, H H
Remove Key C2-C3 C3-C4 C4-C5 C5-C6
26. Rubber Contact26-1 Remove the upper case unit. (See procedure 1)26-2 Remove the UK unit if replacing the rubber con-
tacts on the FSX keyboard assembly U. (See procedure 9)26-3 Remove the panel stopper assemblies if replacing
the rubber contacts on the FSX keyboard assem-bly U. (See procedure 24-3)
26-4 Remove the key stoppers and keys listed in the table 2, corresponding to the rubber contacts to be removed. (Table 2, Fig. 16) (See procedure 24)
26-5 Pull out the rubber contact. (Fig. 16)* The orientation of rubber contacts on the key-
board is previously designated. Pay attention not to install the rubber contacts inversely.
(Fig. 17)* In the installation, install the rubber contact by
pushing it with the end of a clip. (Photo 8)
26. 26-1 126-2 FSX U UK
926-3 FSX U
Ass'y 24-3 26-4 2 2 1624 26-5 16
17
8
Photo 8 ( 8) Fig. 17 ( 17)
-
27
DDK-7
UK UK Unit
[US13A] [US13A]
[US13B]
Upper front rail assemblyU Assy
UK Angle bracketUK
Data line filter
Connector
27. MK49L Circuit Board, MKH-C Circuit Board (Time required: About 9 minutes each)
27-1 Remove the UK unit. (See procedure 9)27-2 Remove the four (4) screws marked [US13A]. The
UK angle bracket can then be removed together with the upper front rail assembly. (Fig. 18)
27-3 Remove the screw marked [US13B]. The data line fi lter can then be removed. (Fig. 18)
27-4 Remove the connector. (Photo 9)27-5 MK-49L Circuit Board27-5-1 Remove the key stoppers L and H. (Table 1, Fig. 16)27-5-2 Remove the keys and the key springs from C2 to
C4. (See procedure 24)27-5-3 Remove the nine (9) screws marked [250A]. The
MK49L circuit board can then be removed. (Photo 10)
27. MK49L MKH-C 927-1 UK 927-2 [US13A] 4 UK
U Ass'y 1827-3 [US13B] 1
1827-4 927-5 MK-49L 27-5-1 LH
1 1627-5-2 C2 C4 24 27-5-3 [250A] 9 MK49L
10
[US13]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 18 ( 18)
Photo 9 ( 9)
-
DDK-7
28
[250A]
Rubber Contact 13 Key A 13Key A
(C2-C3)
Rubber Contact 12 Key A 12Key A
(C#3-C4)
[250A]
[250A]
[250A]
MK49L
27-6 MKH-C Circuit Board, EMKS-FC Circuit Board27-6-1 Remove the key stoppers L and H. (Table 1, Fig. 16)27-6-2 Remove the keys and the key springs from C4 to
C6. (See procedure 24)27-6-3 Remove the nine (9) screws marked [250B]. The
MKH-C circuit board can then be removed. (Photo 11)* The EMKS-FC circuit board is soldered to the
MKH-C circuit board on the connectors.* The rubber contacts are not components of the
MK49L circuit board or MKH-C circuit board. In replacing the MK49L circuit board or MKH-C circuit board, remove the rubber contacts from the circuit board and install them to the new circuit board.
27-6 MKH-C EMKS-FC 27-6-1 LH
1 1627-6-2 C4 C6 24 27-6-3 [250B] 9 MKH-C
11 EMKS-FC MKH-C
MK49L MKH-C
MK49L MKH-C
Photo 10 ( 10)
[250]: Bind Head Tapping Screw-PB BIND3.0X8 MFZN2B3 (WF266600)
MKH-CEMKS-FC
Rubber Contact 12 Key B 12Key B
(C#4-C5)
Rubber Contact 12 Key C 12Key B
(C#5-C6)
[250B][250B]
[250B] [250B][250B]
Photo 11 ( 11)
[250]: Bind Head Tapping Screw-PB BIND3.0X8 MFZN2B3 (WF266600)
-
29
DDK-7
LK LK Unit LK Cover
LK
[LS13B][LS13A]
[LS13C]Data line filter
Connector
28. MK61L Circuit Board, MKH-D Circuit Board (Time required: About 10 minutes each)
28-1 Remove the LK unit. (See procedure 23)28-2 Remove the three (3) screws marked [LS13A] and
loosen the screw marked [LS13B]. The LK cover can then be removed. (Fig. 19)
28-3 Remove the screw marked [LS13C]. The data line fi lter can then be removed. (Fig. 19)
28-4 Remove the connector. (Photo 12)28-5 MK61L Circuit Board28-5-1 Remove the key stoppers L and H. (Table 1, Fig. 16)28-5-2 Remove the keys and the key springs from C1 to
C4. (See procedure 24)28-5-3 Remove the thirteen (13) screws marked [250C].
The MK61L circuit board can then be removed. (Photo 13)
28. MK61L MKH-D 1028-1 LK 23 28-2 [LS13A] 3 [LS13B] 1
LK 1928-3 [LS13C] 1
1928-4 1228-5 MK61L 28-5-1 LH
1 1628-5-2 C1 C4 24 28-5-3 [250C] 13 MK61L
13
[LS13]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 19 ( 19)
Photo 12 ( 12)
-
DDK-7
30
MK61L [250C] [250C]
Rubber Contact 13 Key B 13Key B
(C1-C2)
Rubber Contact 12 Key D 12Key D
(C#2-C3)
Rubber Contact 12 Key E 12Key E
(C#3-C4)
[250C] [250C][250C][250C]
EMKS-FD MKH-D
Rubber Contact 12 Key F 12Key F
(C#4-C5)
Rubber Contact 12 Key G 12Key G
(C#5-C6)
[250D][250D]
[250D] [250D][250D]
28-6 MKH-D Circuit Board, EMKS-FD Circuit Board28-6-1 Remove the key stopper H and key stopper 61.
(Table 1, Fig. 16)28-6-2 Remove the keys and the key springs from C4 to
C6. (See procedure 24)28-6-3 Remove the nine (9) screws marked [250D]. The
MKH-D circuit board can then be removed. (Photo 14)* The EMKS-FD circuit board is soldered to the
MKH-D circuit board on the connectors.* The rubber contacts are not components of the
MK61L circuit board or MKH-D circuit board. In replacing the MK61L circuit board or MKH-D circuit board, remove the rubber contacts from the circuit board and install them to the new circuit board.
28-6 MKH-D EMKS-FD 28-6-1 H 61
1 1628-6-2 C4 C6 24 28-6-3 [250D] 9 MKH-D
14 EMKS-FD MKH-D
MK61L MKH-D
MK61L MKH-D
Photo 13 ( 13)
[250]: Bind Head Tapping Screw-PB BIND3.0X8 MFZN2B3 (WF266600)
Photo 14 ( 14)
[250]: Bind Head Tapping Screw-PB BIND3.0X8 MFZN2B3 (WF266600)
-
31
DDK-7
Disassembly of DDKU-P7
29. EXP Pedal (2CH) and EXP (2CH) Circuit Board (Time required: About 1 minute)
29-1 Remove the screw marked [25A]. The EXP pedal (2CH) can then be removed. (Fig. 20)
29-2 Remove the four (4) screws marked [31]. The cover can then be removed. (Photo 15)
29-3 Remove the screw marked [24]. The EXP (2CH) circuit board can then be removed. (Photo 16)
29-4 Remove the actuator, coil spring, plate, and hex-agonal nut from the EXP (2CH) circuit board. (Photo 17)
* When installing the EXP (2CH) circuit board, set the pedal plate in the Minimum Volume position.
30. EXP Pedal (2ND) and EXP (2ND) Circuit Board (Time required: About 1 minute)
30-1 Remove the screw marked [25B]. The EXP pedal (2ND) can then be removed. (Fig. 20)
30-2 Remove the four (4) screws marked [21]. The cover can then be removed. (Photo 18)
30-3 Remove the screw marked [17]. The EXP (2ND) circuit board can then be removed. (Photo 19)
30-4 Remove the actuator, coil spring, plate, and hex-agonal nut from the EXP (2ND) circuit board. (Photo 20)
DDKU-P7
29. EXP 2CHEXP (2CH) 129-1 [25A] 1 EXP 2CH
2029-2 [31] 4 1529-3 [24] 1 EXP2CH
1629-4
EXP2CH 17 EXP2CH
30. EXP 2NDEXP (2ND) 130-1 [25B] 1 EXP 2ND
2030-2 [21] 4 1830-3 [17] 1 EXP2ND
1930-4
EXP2ND 20
EXP Pedal (2CH)EXP2CH
EXP Pedal (2ND)EXP2ND
[25A][25B]
Fig. 20 ( 20)
[25]: Bind Head Screw BIND4.0X10 MFZN2B3 (WE980400)
-
DDK-7
32
[31]
EXP(2CH)
Cover
[24]
EXP(2CH)
Actuator
Coil spring
Hexagonal nutPlate
EXP (2CH)
31. Pedal Keyboard Assembly (Time required: About 3 minutes)31-1 Remove the EXP pedal (2CH). (See procedure 29)31-2 Remove the EXP pedal (2ND). (See procedure 30)31-3 Remove the fi ve (5) screws marked [15A] and fi ve
(5) screws marked [16]. The PK protector assem-bly can then be removed. (Fig. 21)
31-4 Remove the two (2) screws marked [15B] and loosen the fi ve (5) screws marked [14]. The pedal keyboard assembly can then be removed. (Fig. 22)
* Pay attention not to pull the connector assembly when removing the pedal keyboard assembly.
31. Ass'y 331-1 EXP 2CH29 31-2 EXP 2ND30 31-3 [15A] 5 [16] 5PK
Ass'y 2131-4 [15B]2[14]5
Ass'y 22 Ass'y
[31]: Bind Head Tapping Screw-P P BIND 4.0X8 MFZN2B3 (WF492100)
Photo 15 ( 15)
[24]: Bind Head Tapping Screw-P P BIND 3.0X6 MFZN2W3 (WF026400)
Photo 16 ( 16)
Photo 17 ( 17)
EXP Pedal (2CH)
[21]: Bind Head Tapping Screw-P P BIND 4.0X8 MFZN2B3 (WF492100)
Photo 18 ( 18)
[17]: Bind Head Tapping Screw-P P BIND 3.0X6 MFZN2W3 (WF026400)
Photo 19 ( 19)
Photo 20 ( 20)
EXP Pedal (2ND)
[21]
Cover
EXP(2ND)
[17]
EXP(2ND)
EXP (2ND)
Actuator
Coil spring
Hexagonal nutPlate
-
33
DDK-7
[15A]
[16]
[15A][15A][15A]PK Protector assemblyPKAssy
[16]
[15B]
[15B][6F][6F]
[14] [14]
Pedal keyboard assemblyAssy
Cover AA
[15]: Bind Head Tapping Screw-BB BIND4.0X25 MFZN2W3 (WJ011400)[16]: Bind Head Tapping Screw-SS BIND3.0X10 MFZN2W3 (WE974200)
Fig. 21 ( 21)
[6]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)[14]: Bind Head Tapping Screw-SS BIND4.0X10 MFZN2W3 (WF269100)[15]: Bind Head Tapping Screw-BB BIND4.0X25 MFZN2W3 (WJ011400)
Fig. 22 ( 22)
-
DDK-7
34
[20] [20]Handle set
Cap
Cap
32. Handle Set (Time required: About 1 minute)32-1 Remove the two (2) caps. (Fig. 23)32-2 Remove the two (2) screws marked [20]. The han-
dle set can then be removed. (Fig. 23)* The screws marked [20] are not components of
the handle set. When replacing the handle set, remove the screws marked [20] and install them to the new handle set.
33. Disassembly of the Pedal Keyboard Ass-embly (PK-L Circuit Board, PK-H Circuit Board, White Keys and Black Keys)
33-1 Remove the pedal keyboard assembly. (See procedure 31)33-2 PK-L Circuit Board (Time required: About 4 minutes)33-2-1 Remove the eight (8) screws marked [11A]. The
PK-L circuit board can then be removed. (Fig. 24)33-3 PK-H Circuit Board (Time required: About 4 minutes)33-3-1 Remove the five (5) screws marked [11B]. The
PK-H circuit board can then be removed. (Fig. 24)33-4 White Keys33-4-1 Remove the screw marked [8A] and the hexago-
nal nut marked [12A]. The white keys can then be removed. (Fig. 24)
33-5 Black Keys33-5-1 Remove the screw marked [8B] and the hexago-
nal nut marked [12B]. The black keys can then be removed. (Fig. 24)
* When replacing any of C0 to G1 pedal keys (white keys), remove the key stoppers and in-stall them on the new pedal keys (white keys).
(Fig. 24, Photo 21)
32. 132-1 2 2332-2 [20] 2
23 [20]
[20]
[20]: Flat Head Screw FLAT5.0X16 MFZN2W3 (WH746000)
Fig. 23 ( 23)
33. Ass'y PK-L PK-H 33-1 Ass'y 31 33-2 PK-L 4 33-2-1 [11A] 8PK-L
2433-3 PK-H 4 33-3-1 [11B] 5PK-H
2433-4 33-4-1 [8A] [12A]
2433-5 33-5-1 [8B] [12B]
24 C0 G1
24 21
-
35
DDK-7
34. PK Cover (Time required: About 6 minutes)34-1 Remove the EXP pedal (2CH). (See procedure 29)34-2 Remove the EXP pedal (2ND). (See procedure 30)34-3 Remove the PK protector assembly. (See procedure 31-3)34-4 Remove the pedal keyboard assembly. (See procedure 31-4)34-5 Remove the nine (9) screws marked [6A]. The rear
angle assembly can then be removed. (Fig. 25)34-6 Remove the seven (7) screws marked [6B]. The
cover C assembly can then be removed. (Fig. 25)34-7 Remove the four (4) each screws marked [6C].
The two (2) holder EXP assemblies can then be removed. (Fig. 26)
34-8 Remove the twelve (12) screws marked [6D]. The front angle and rail can then be removed. (Fig. 26)
34-9 Remove the two (2) screws marked [6E]. The stand base assembly L can then be removed.
(Fig. 26)* The stand base assembly R can be removed in
the same way.34-10 Remove the two (2) screws marked [6F]. The
cover A can then be removed. (Fig. 22)34-11 Remove the screw marked [2e]. The data line fi lter
can then be removed. (Fig. 26)34-12 Remove the two (2) screws marked [2d]. The
PK-B connector assembly can then be removed. (Fig. 26)
34-13 Remove the two (2) screws marked [3]. The angle can then be removed. (Fig. 26)
White key
Key stopper
Bottom view
Black keyWhite key
Black keyWhite key
C0 G1
[11A] [11B]
[8A] [8B]
[12A] [12B]
Side view
Top viewPK-HPK-L
Photo 21 ( 21)
[8]: Screw6.5X38.5 MFZN2W3 (WF053800)[11]: Bind Head Tapping Screw-SS BIND3.0X10 MFZN2W3 (WE974200)[12]: Hexagonal NutM4 (WF567000)
Fig. 24 ( 24)
34. PK 634-1 EXP 2CH29 34-2 EXP 2ND30 34-3 PK Ass'y 31-3 34-4 Ass'y 31-4 34-5 [6A] 9
2534-6 [6B] 7 C
2534-7 [6C] 4 EXP Ass'y
2 2634-8 [6D] 12
2634-9 [6E] 2 L
26 R34-10 [6F] 2 A 2234-11 [2e] 1
2634-12 [2d] 2PK-B
2634-13 [3] 2E 26
-
DDK-7
36
Rear angle assembly C
Cover C assembly[6A] [6A] [6A] [6A][6B]
[6A]
[6B] [6B] [6A]
[6]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 25 ( 25)
[2d]: Pan Head Screw PAN3.0X5 MFZN2W3 (WE945700)[2e]: Bind Head Tapping Screw-BB BIND4.0X8 MFZN2W3 (WE974600)[3]: Bind Head Tapping Screw-BB BIND4.0X8 MFZN2W3 (WE974600)[6]: Bind Head Tapping Screw-BB BIND4.0X12 MFZN2W3 (WE981200)
Fig. 26 ( 26)
EXPAssyHolder EXP assembly
EXPAssyHolder EXP assembly
RStand base assembly R
Rail
Front angle
EAngle
PK-BPK-B Connector assembly
[6D]
[6D]
[6C]
[6E][6E]
[6D] [6D] [6D] [6D]
[6C]
[2d][2d]
[2e]
[3]
LStand base assembly L
Data line filter
-
37
DDK-7
LSI PIN DESCRIPTIONLSI
AK4393VF-E2 (XW029A00) DAC (Digital to Analog Converter) ...................................41AK5381VT-E2 (X5219A00) ADC ...................................................................................37HD6417709SHF200B (X2687A00) CPU (SH3) ............................................................40HD6417709SHF200BV (X2687B00) CPU (SH3) ..........................................................40HD6417727F160CV (X2890B00) CPU .........................................................................39HD6433693B92HV (X84721000) FVS ..........................................................................42M34519M6-521FP W4 (X5646200) CPLD ....................................................................37M38044M4-C16FPU0 (X4406100) CPU (LED DRIVER/SWITCH SCAN) ....................42M38869M8A-184GP (X5343100) CPU .........................................................................38MBCG46183-129-PFV (XV833A00) SIO4 (Gate Array) ................................................45S1L50553F21Y000 (X4195A00) Gate Array ................................................................41SN75LVDS84ADGGR (X4212A00) LVDS TRANSMITTERS ........................................45T8F02TB-0102 (X0060A00) SWP50 (Tone Generator) ................................................43TUSB2046BVFR (X4704A00) 4-PORT USB HUB .......................................................38
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
12345678
AINRAINLCKS1VCOMAGND
VAVD
DGND
IIIO----
Rch Analog input pinLch Analog input pinMode select 1 pinCommon voltage output pinAnalog groundAnalog power supplyDigital power supplyDigital ground
910111213141516
SDTOLRCKMCLKSCLKPDNDIF
CKS2CKS0
OI/OI
I/OIIII
Audio serial data output pinOutput channnel clock pinMaster clock input pinAudio serial data clock pinPower down mode pinAudio interface format pinMode select 2 pinMode select 0 pin
DAC2A: IC401AK5381VT-E2 (X5219A00) ADC
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
101112131415161718192021
P13D0D1D2D3D4D5
D6/CNTR0D7/CNTR1
P50P51P52P53
P20/SCKP21/SOUTP22/SINRESETCNVSSXOUTXINVSS
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OOI
Port P1 serves as a 4-bit I/O port
Each pin of port D has an independent 1-bit wide I/O function
Each pin of port D has an independent 1-bit wide I/O function / CNTR0Each pin of port D has an independent 1-bit wide I/O function / CNTR1
Port P5 serves as a 4-bit I/O port
Port P2 serves as a 3-bit I/O port / Serial I/O data transfer synchronous clock I/O pinPort P2 serves as a 3-bit I/O port / Serial I/O data output pinPort P2 serves as a 3-bit I/O port / Serial I/O data input pinAn N-channel open-drain I/O pin for a system resetConnect CNVSS to VSS and apply L (0V) to CNVSS certainly
I/O pins of the main clock generating circuit Ground
222324252627282930313233343536373839404142
VDDVDCE
P30/INT0P31/INT1
P32P33
P60/AIN0P61/AIN1P62/AIN2P63/AIN3P40/AIN4P41/AIN5P42/AIN6P43/AIN7
P00P01P02P03P10P11P12
I
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
Power supply +5V This pin is used to operate/stop the voltage drop detection circuitPort P3 serves as a 4-bit I/O port / INT0 pin and INT1 pin accept external interrupts
Port P3 serves as a 4-bit I/O port
Port P6 serves as a 4-bit I/O port / A/Dconverter analog input pins
Port P4 serves as a 4-bit I/O port / A/D converter analog input pins
Port P0 serves as a 4-bit I/O port
Port P1 serves as a 4-bit I/O port
M34519M6-521FP W4 (X5646200) CPLD (Complex Programmable Logic Device) PN: IC7
-
DDK-7
38
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
10111213141516
DP0DM0VCC
RESETEECLK
EEDATA/GANGEDGND
BUSPWRPWRON1OVRCUR1
DM1DP1
PWRON2OVRCUR2
DM2DP2
I/OI/O-IOI/O-IOI
I/OI/OOI
I/OI/O
Differential data plusDifferential data minusPower supplyResetEEPROM serial clockEEPROM serial data / Power management mode indicatorGroundPower source indicatorPower-on/-off control signalOver-current inputDifferential data minusDifferential data plusPower-on/-off control signalOver-current inputDifferential data minusDifferential data plus
17181920212223242526272829303132
PWRON3OVRCUR3
DM3DP3
PWRON4OVRCUR4
DM4DP4VCC
EXTMEMTSTPLL
GNDXTAL2XTAL1
TSTMODESUSPND
OI
I/OI/OOI
I/OI/O-I
I/O-OIIO
Power-on/-off control signalOver-current inputDifferential data minusDifferential data plusPower-on/-off control signalOver-current inputDifferential data minusDifferential data plusPower supplyEEPROM read enableTest pinGround
Crystal oscillator
Test pinSuspend status
HUB: IC001TUSB2046BVFR (X4704A00) 4-PORT USB HUB
DM2: IC055PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
10111213141516171819202122232425262728293031323334353637383940
P60/AN0P77/SCLP76/SDAP75/INT41P74/INT31P73/SRDY2/INT21P72/SCLK2P71/SOUT2P70/SIN2
P57/DA2/PWM11P56/DA1/PWM01P55/CNTR1P54/CNTR0P53/INT40/WP52/INT30/RP51/INT20/S0
P50/A0S1
OBF10P45/TXDP44/RXDOBF01OBF00CNVSSRESET
P41/XCINP40/XOUT
XINXOUTVSSP27P26P25P24P23P22P21P20P17P16
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
I/OI/O
-I
I/OI/OIO-
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
Port 6 / Analog inputPort 7 / Serial clockPort 7 / Serial data
Port 7 / Interrupt request
Port 7 / Serial control reqister / Interrupt requestPort 7 / Serial clockPort 7 / Serial outputPort 7 / Serial input
Port 5 / D-A output /PWM output
Port 5 / Timer
Port 5 / Interrupt request / WritePort 5 / Interrupt request / readPort 5 / Interrupt request / Port 5 / Address
Port 4 / Data transmissionPort 4 / Data reception
GroundSystem reset inputPort 4 /Port 4 /
8MHz
Ground
Port 2
Port 2
41424344454647484950515253545556575859606162636465666768697071727374757677787980
P15P14P13P12P11P10P07P06P05P04P03P02P01
P00/P3REFP37P36P35P34P33P32
P31/PWM10P30/PWM00P87/DQ7P86/DQ6P85/DQ5P84/DQ4P83/DQ3P82/DQ2P81/DQ1P80/DQ0
VCCVREFAVSS
P67/AN7P66/AN6P65/AN5P64/AN4P63/AN3P62/AN2P61/AN1
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O-I-
I/OI/OI/OI/OI/OI/OI/O
Port 1
Port 0
Port 0 / Port 3 reference
Port 3
Port 3 / PWM output
Port 8 /
Power supply +5VVoltage referenceGround
Port 6 / Analog input
M38869M8A-184GP (X5343100) CPU
-
39
DDK-7
PINNO.
123456789
101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899
100101102103104105106107108109110111112113114115116117118119120
Vcc-RTCXTAL2
EXTAL2Vss-RTC
MD1MD2NMI
IRQ0/IRL0_/PTH[0]IRQ1/IRL1_/PTH[1]IRQ2/IRL2_/PTH[2]IRQ3/IRL3_/PTH[3]
IRQ4/PTH[4]VEPWCVCPWC
MD5/BREQ/BACKVssQ
CKIO2VccQ
D31/PTB[7]D30/PTB[6]D29/PTB[5]D28/PTB[4]D27/PTB[3]D26/PTB[2]D25/PTB[1]D24/PTB[0]
VssQD23/PTA[7]
VccQD22/PTA[6]D21/PTA[5]D20/PTA[4]
VssD19/PTA[3]
VccD18/PTA[2]D17/PTA[1]D16/PTA[0]
D15VssQD14
VccQD13D12D11D10D9D8D7D6
VssQD5
VccQD4D3D2D1D0A0A1A2
VssQA3
VccQA4A5A6A7A8A9
A10A11
VssQA12
VccQA13A14A15A16A17A18A19A20
VssQA21
VccQA22A23VssA24VccA25
BS_/PTK[4]RD_
WE0_/DQMLLWE1_/DQMLU/WE
WE2_/DQMUL/ICIORD_/PTK[6]VssQ
WE3_/DQMUU/ICIOWR_/PTK{7}VccQ
RD/WR_PTE[7]/PCC0RDY/AUDSYNC_
/CS0/CS2/CS3
/CS4/PTK[2]/CS5/CE1A_/PTK[3}
/CS6/CE1B_CE2A_/PTE[4]CE2B_/PTE[5]
AFE_HC1/USB1d_DPLS/PTK[0]AFE_RLYCNT_/USB1d_DMNS/PTK[1]
VssQAFE_SCLK/USB1d_TXDPLS
VccQPTM[7]/PTINT[7]/AFE_FS/USB1d_RCV
PTM[6]/PTINT[6]/AFE_RXIN/USB1d_SPEEDPTM[5]/PTINT[5]/AFE_TXOUT/USB1d_TXSE0
-------IIIIIO-------
I/OI/OI/OI/OI/OI/OI/OI/O-
I/O-
I/OI/OI/O-
I/O-
I/OI/OI/O------------------------------------------------------O-OOO-O-OO---OOOOOOO-I-III
Power supply for RTC (1.9V)
Not in use (XTAL for internal RTC)
Power supply for RTC (0V)
Clock mode setting
Not in use (Non-maskable interrupt request)
External interrupt request
VEE control pin for LCD panelVCC control pin for LCD panelBig endian settingNot in use (bus request)Bus acknowledgeVssQSystem clock outputVccQ
Data bus
VssQData busVccQ
Data bus
VssData busVcc
Data bus
VssQData busVccQ
Data bus
VssQData busVccQ
Data bus
Address bus
VssQAddress busVccQ
Address bus
VssQAddress busVccQ
Address bus
VssQAddress busVccQ
Address bus
VssAddress busVccAddress busNot connected (bus cycle start signal)Read strobeWrite 0 signalWrite 1 signalWrite 2 signalVssQWrite 3 signalVccQRead/WriteI/OChip Select 0Chip Select 2Chip Select 3Chip Select 4Chip Select 5Chip Select 6Output port (SWP50 Reset)Output port (PLG Board Reset)SPD DATASPD CLVssQNot in use (USB1 D+ transmission)VccQ
Not in use
PINNO.121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240
PTM[4]/PINT[4]/AFE_RDET_/USB1d_TXDMNSReserved/USB1d_SUSPENDUSB1_ovr_crnt/USBF_VBUS
USB2_ovr_crnt_RTS2_/USB1d_TXENLPTE[2]/USB1_pwr_enPTE[1]/USB2_pwr_en
CKE/PTK[5]/RAS3/PTJ[0]
Reserved/PTJ[1]Reserved//CAS/PTJ[2]
VssQReserved/PTJ[3]
VccQReserved/PTJ[4]Reserved/PTJ[5]
VssPTD[5]/CL1
VccPTD[7]/DON
PTE[6]/M_DISPPTE[3]/FLMPTE[0]/TDO
PCC0RESET/DRACK0PCC0DRV_/DACK0_
/WAIT/RESETM
/ADTRG/PTH[5]/IOIS16/PTG[7]
/ASEMD0PTG[5]/ASEBRKAK_
PTG[4]PCC0BVD2/PTG[3]/AUDATA[3]PCC0BVD1/PTG[2]/AUDATA[2]
VssPCC0CD2/PTG[1]/AUDATA[1]
VccPCC0CD1/PTG[0]/AUDATA[0]
VssQPTF[7]/PINT[15]/TRST_
VccQPTF[6]/PINT[14]/TMSPTF[5]/PINT[13]/TDIPTF[4]/PINT[12]/TCK
PTF[3]/PINT[11]/ReservedPCCREG_/PTF[2]/ReservedPCC0VS1_/PTF[1]/ReservedPCC0VS2_/PTF[0]/Reserved
MD0Vcc-PLL1
CAP1Vss-PLL1Vss-PLL2
CAP2Vcc-PLL2
PCC0WAIT_/PTH[6]/AUDCKVssVcc
XTALEXTAL
LCD15/PTM[3]/PINT[10]LCD14/PTM[2]/PINT[9]LCD13/PTM[1]/PINT[8]
LCD12/PTM[0]STATUS0/PTJ[6]STATUS1/PTJ[7]
CL2/PTH[7]VssQCKIOVccQ
TxD0/SCPT[0]SCK0/SCPT[1]
TxD_SIO/SCPT[2]SIOMCLK/SCPT[3]
TxD2/SCPT[4]SCK_SIO/SCPT[5]
SIOFSYNC/SCPT[6]RxD0/SCPT[0]
RxD_SIO/SCPT[2]Vss
RxD2/SCPT[4]Vcc
SCPT[7]/CTS2_/IRQ5LCD11/PTC[7]/PINT[3]LCD10/PTC[6]/PINT[2]LCD9/PTC[5]/PINT[1]
VssQLCD8/PTC[4]/PINT[0]
VccQLCD7/PTD[3]LCD6/PTD[2]LCD5/PTC[3]LCD4/PTC[2]LCD3/PTC[1]LCD2/PTC[0]LCD1/PTD[1]LCD0/PTD[0]
DREQ0_/PTD[4]LCK/UCLK/PTD[6]
/RESETPCA
MD3MD4
/Scan_testenAvcc_USBUSB1_PUSB1_M
Avss_USBUSB2_PUSB2_M
Avcc_USBAvss
AN[2]/PTL[2]AN[3]/PTL[3]AN[4]/PTL[4]AN[5]/PTL[5]
AvccAN[6]/PTL[6]/DA[1]AN[7]/PTL[7]/DA[0]
Avss
IOI-OOOOOOO-O-OO-O-OOOOOO--II-
III-I-I-I-IIIIIII-------I----IIIIOOO---OOOOOOOii-i-IOOO-O-OOOOOOOOII------
IOIO-
IOIO--IIII-IO-
Not in use
USB function VBUSUSB2_HOST2 over current detectionNot in useUSB1 voltage controlUSB2 voltage controlEnable (SDRAM)RAS for SDRAMNot in useCAS for SDRAMVssQOutput port (DAC Reset)VccQOutput port (SIO Reset)Output port (DAC Mute)VssLCD line clockVccLCD DISPLAY ONLCD alternaterLCD frame line markerJTAG (test data output)DMA request acceptanceDMA acknowledgeHardware wait requestManual reset requestAnalog A/D trigger
Not in use
VssNot in useVccNot in useVssQNot in useVccQ
Not in use
Clock mode settingPower supply for Vcc_PLL1 - PLL1(1.9V)External capacitance for CAP1 _ PLL1Power supply for Vss_PLL1 _ PLL1(0V)Power supply for Vss_PLL2 _ PLL2 (0V)External capacitance for CAP2 _ PLL2Power supply for Vcc_PLL2 _ PLL2 (1.9V)Not in useVssVccClock oscillatorExternal clock
Not in use
Input port (Flash ROM RY/BY)Output port (Flash ROM write protect)Output port (Flash ROM ACC)LCD clock outputVssQSystem clock input/output (for SDRAM)VccQOutput port for SCI
Not in use
Output port for SCI
Not in use
Receiving data 0Not in useVssReceiving data 2VccNot in useOutput port (PLG CLOCK ON/OFF)
Not in use
VssQNot in useVccQLCD DATA7LCD DATA6LCD DATA5LCD DATA4LCD DATA3LCD DATA2LCD DATA1LCD DATA0DMA requestUSB clockPower on reset requestHardware standby request
Bus width setting for area0
Test pin (fixed to 3.3V)USB analog power supply (3.3V)USB1 data input/output (+)USB1 data input/output (-)USB analog power supply (0V)USB2 data input/output (+)USB2 data input/output (-)USB analog power supply (3.3V)A/D analog power supply (0V)
AD converter input
A/D analog power supply (3.3V)AD converter inputDA converter output (LCD contrast)A/D analog power supply (0V)
I/O I/ONAME FUNCTION FUNCTIONNAME
HD6417727F160CV (X2890B00) CPU DM2: IC006
-
DDK-7
40
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899
100101102103104
MD1MD2
Vcc(RTC)XTAL2
EXTAL2Vss(RTC)
NMIIRQ0/IRL0/PTH0IRQ1/IRL1/PTH1IRQ2/IRL2/PTH2IRQ3/IRL3/PTH3IRQ4/PTH4D31/PTB7D30/PTB6D29/PTB5D28/PTB4D27/PTB3D26/PTB2
VssQD25/PTB1
VccQD24/PTB0D23/PTA7D22/PTA6D21/PTA5D20/PTA4
VssD19/PTA3
VccD18/PTA2D17/PTA1D16/PTA0
VssQD15
VccQD14D13D12D11D10D9D8D7D6
VssQD5
VccQD4D3D2D1D0A0A1A2A3
VssQA4
VccQA5A6A7A8A9
A10A11A12A13
VssQA14
VccQA15A16A17A18A19A20A21VssA22VccA23
VssQA24
VccQA25
BS/PTK4RD
WE0/DQMLLWE1/DQMLU/WE
WE2/DQMUL/ICIORD/PTK6WE3/DQMUU/ISIOWR/PTK7
RD/WRAUDSYNC/PTE7
VssQCS0/MCS0
VccQCS2/PTK0CS3/PTK1CS4/PTK2
CS5/CE1A/PTK3CS6/CE1BCE2A/PTE4CE2B/PTE5
II-OI-IIIIII
I/OI/OI/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/O-
I/O-
I/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OI/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OOOOO-O-OOOOOOOOO-O-OOOOOOO-O-O-O-OI/OOOOI/OI/OOI/O-O-
I/OI/OI/OI/OOI/OI/O
Mode control
Power supply +1.8 V
Crystal oscillator
GroundNon-maskable interrupt request
Interrupt request / Port H
Data bus / Port B
GroundData bus / Port BPower supply +3.3 VData bus / Port B
Data bus / Port A
GroundData bus / Port APower supply +1.8 V
Data bus / Port A
GroundData busPower supply +3.3 V
Data bus
GroundData busPower supply +3.3 V
Data bus
Address bus
GroundAddress busPower supply +3.3 V
Address bus
GroundAddress busPower supply +3.3 V
Address bus
GroundAddress busPower supply +1.8 VAddress busGroundAddress busPower supply +3.3 VAddress busBus cycle / Port KRead strobeSelect signal (D7-D0) / D QM (SDRAM)Select signal (D15-D8) / D QM (SDRAM) / Write enableSelect signal (D23-D16) / D QM (SDRAM) / I/O read / Port KSelect signal (D31-D24) / D QM (SDRAM) / I/O write / Port KRead / WriteAUD cycle / Port EGroundChip select / Mask ROM chip selectPower supply +3.3V
Chip select / Port K
Chip select / Chip enable / Port KChip select / Chip enable
Chip enable / Port E
105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208
CKE/PTK5RAS3L/PTJ0
PTJ1CASL/PTJ2
VssQCASU/PTJ3
VccQPTJ4PTJ5
DACK0/PTD5DACK1/PTD7
PTE6PTE3
RAS3U/PTE2PTE1
TDO/PTE0BACKBREQWAIT
RESETMADTRG/PTH5IOIS16/PTG7ASEMD0/PTG6ASEBRKAK/PTG5PTG4/CKIO2AUDATA3/PTG3AUDATA2/PTG2
VssAUDATA1/PTG1
VccAUDATA0/PTG0TRST/PTF7/PINT15TMS/PTF6/PINT14TDI/PTF5/PINT13TCK/PTF4/PINT12IRLS3/PTF3/PINT11IRL2/PTF2/PINT10IRLS1/PTF1/PINT9IRLS0/PTF0/PINT8
MD0Vcc(PLL1)
CAP1Vss(PLL1)Vss(PLL2)
CAP2VCC(PLL2)AUDCK/PTH6
VssVssVcc
XTAL1EXTAL1
STATUS0/PTJ6STATUS1/PTJ7TCLK/PTH7
/IRQOUTVssQCKIOVccQ
TXD0/SCPT0SCK0/SCPT1TXD1/SCPT2SCK1/SCPT3TXD2/SCPT4SCK2/SCPT5RTS2/SCPT6RXD0/SCPT0RXD1/SCPT2
VssRXD2/SCPT4
VccCTS2/IRQ5/SCPT7
MCS7/PTC7/PINT7MCS6/PTC6/PINT6MCS5/PTC5/PINT5MCS4/PTC4/PINT4
VssQWAKEUP/PTD3
VccQRESETOUT/PTD2MCS3/PTC3/PINT3MCS2/PTC2/PINT2MCS1/PTC1/PINT1MCS0/PTC0/PINT0DRAK0/PTD1DRAK1/PTD0DREQ0/PTD4DREQ1/PTD6
RESETPCA
MD3MD4MD5AVss
AN0/PTL0AN1/PTL1AN2/PTL2AN3/PTL3AN4/PTL4AN5/PTL5
AVccAN6/DA1/PTL6AN7/DA0/PTL7
AVss
I/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OI/OI/OI/OI/OOIIIIII
I/OI/OI/OI/O-
I/O-
I/OIIIIIIIII------I---OI
I/OI/OI/OO-
I/O-OI/OOI/OOI/OI/OII-I-I
I/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OI/OI/OIIIIIII-IIIIII-
I/OI/O-
CK enable / Port KRAS address bus / Port JPort JCAS address bus / Port JGroundCAS address bus / Port JPower supply +3.3 V
Port J
DMA acknowledge / Port D
Port E
RAS address bus / Port EPort ETest data / Port EBus acknowledgeBus requestHardware wait requestManual reset Analog trigger / Port HWrite protect / Port GASE mode / Port GASE break acknowledge / Port GPort G / Clock output
AUD data / Port G
GroundAUD data / Port GPower supply +1.8 VAUD data / Port GTest reset / Port F / Port interruptionTest mode switch / Port F / Port interruptionTest data / Port F / Port interruptionTest clock / Port F / Port interruption
Interrupt request / Port F / Port interruption
Mode controlPower supply +1.8 VCapacitorGroundGroundCapacitorPower supply +1.8 VAUD clock / Port H
Ground
Power supply +1.8 V
Crystal oscillator
Processor status / Port J
Timer clock / Port HInterrupt request outputGroundSystem clock input / outputPower supply +3.3 VData transmission / SCI portSerial clock / SCI portData transmission / SCI portSerial clock / SCI portData transmission / SCI portSerial clock / SCI portTransmit request / SCI port
Data reception / SCI port
GroundData reception / SCI portPower supply +1.8 VTransmit clear / Interrupt request / SCI port
Mask ROM chip select / Port C / Port interruption
GroundStandby mode Interrupt request output / Port DPower supply +3.3 VReset output / Port D
Mask ROM chip select / Port C / Port interruption
DMA acknowledge / Port D
DMA request / Port D
Power on resetChip active
Mode control
Analog ground
Analog input / Port L
Analog power supply +3.3 V
Analog input / Analog output / Port L
Analog ground
HD6417709SHF200BV (X2687B00) CPU (SH3)HD6417709SHF200B (X2687A00) CPU (SH3)
TG1-E2: IC001, TG2A (TG2): IC001TG1-E1: IC001, TG1-E2: IC001, TG2A (TG2): IC001
-
41
DDK-7
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
1011121314
DVSSDVDDMCLK/PD
BICKSDATALRCK
SMUTE//CSDFS
DEM0/CCLKDEM1/CDTI
DIF0DIF1DIF2
--IIIIIIIIIIII
Digital groundDigital power supplyMaster clockPower down modeAudio serial data clockAudio serial data inputL/R clockSoft muteDouble speed sampling mode
De-emphasis enable
Digital input format
1516171819202122232425262728
BVSSVREFLVREFHAVDDAVSS
AOUTR-AOUTR+AOUTL-AOUTL+VCOMP//S
CKS0CKS1CKS2
-II--OOOOOIIII
Substrate groundLow level voltage referenceHigh level voltage referenceAnalog power supply +5 VAnalog groundRch negative analog outputRch positive analog outputLch negative analog outputLch positive analog outputCommon voltage outputParallel/serial select
Master clock select
AK4393-VS-E2 (XW029A00) DAC (Digital to Analog Converter) DAC2A: IC201, IC301
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
10111213141516171819202122232425262728293031323334353637383940
CLKICLKOVDD
SCANENBATPGENB
VSSPLLTESTPLLRESPLLVSSMVDD
PLLVSSAVDDCHG0LPVSS
VSSMIRQMCSMWRMRDMAVDDMD0MD1MD2MD3MD4MD5MD6MD7VSSMD8VDDMD9
MD10MD11MD12MD13MD14MD15VSS
IO-
I/OI/O-II----
--
I/OIII
-I/OI/OI/OI/OI/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OI/OI/O-
Clock
Power supplyScan enable
GroundTestResetGroundPower supplyGroundAnalog power supply
Ground
Interrupt requestControl portWriteRead
Power supply
DRAM data bus
GroundDRAM data busPower supply
DRAM data bus
Ground
41424344454647484950515253545556575859606162636465666768697071727374757677787980
VDDRESET
VSSOUT4OUT3INP2INP1INP0
TESTENBVSS
OSCOVDD
OSCIVSS
SIRQSCSSWRSRDSAVSSVDDSD0SD1SD2SD3SD4SD5SD6SD7VSSSD8VDDSD9
SD10SD11SD12SD13SD14SD15VSS
-I-OOIII
I/O-
-
-I/OIII
--
I/OI/OI/OI/OI/OI/OI/OI/O-
I/O-
I/OI/OI/OI/OI/OI/OI/O-
Power supplyResetGround
Output
Input
Test enableGround
Power supply
GroundInterrupt requestControl portWriteRead
GroundPower supply
Serial data
GroundSerial dataPower supply
Serial data
Ground
TG1-E1: IC005, TG1-E2: IC005, TG2A (TG2): IC004S1L50553F21Y000 (X4195A00) Gate Array
-
DDK-7
42
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
1011121314151617181920212223242526272829303132
NCNC
AVCCX2X1VCLRESTESTVSS
OSC2OSC1VCC
P50/WKP0P51/WKP1
NCNCNCNC
P52/WKP2P53/WKP3P54/WKP4P55/WKP5/ADTRGP10/TMOW
P11P12SDASCL
P74/TMRIVP75/TMCIVP76/TMOV
NCNC
-OI-II-OI-
I/OI/O
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
Not used
Power supply
Crystal resonator
Power supplyReset pinTest pinGround
Crystal or ceramic resonator
Power supply
8-bit I/O port / Interrupt request
Not used
8-bit I/O port / Interrupt request
8-bit I/O port / Interrupt request / A/D converter trigger
7-bit I/O port
IIC data I/O pin
3-bit I/O port / Timer
Not used
3334353637383940414243444546474849505152535455565758596061626364
NCNCNMI
P80/FTCIP81/FTIOAP82/FTIOBP83/FTIOCP84/FTIOD
P85P86P87
P20/SCK3P21/RXDP22/TXD
NCNCNCNC
P14/IRQ0P15/IRQ1P16/IRQ2P17/IRQ3/TRGVPB4/AN4PB5/AN5PB6/AN6PB7/AN7PB3/AN3PB2/AN2PB1/AN1PB0/AN0
NCNC
II/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O
Not used
Non maskable interrupt8-bit I/O port / External event input8-bit I/O port / Output compare8-bit I/O port / Output / input capture8-bit I/O port / Input PWM8-bit I/O port / Output
8-bit I/O port
3-bit I/O port / Clock3-bit I/O port / Receive data input3-bit I/O port / Transmit data output
Not used
7-bit I/O port / Interrput request
7-bit I/O port / Interrput request / Trigger input
8-bit I/O port / Analog input
Not used
EMKS-FC: IC005, EMKS-FD: IC005HD6433693B92HV (X8472100) FSV (CPU: H8/3694)
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
1011121314151617181920212223242526272829303132
P62/AN2P61/AN1P60/AN0P57/INT3P56/PWMP55/CNTR1P54/CNTR0P53/SRDY2P52/SCLK2P51/SOUT2P50/SIN2
P47/SRDY1/CNTR2P46/SCLK1P45/TXD1P44/RXD1P43/INT2P42/INT1CNVSSRESET
P41/INT00/XCINP40/INT40/XCOUT
XINXOUTVSS
P27(LED7)P26(LED6)P25(LED5)P24(LED4)P23(LED3)P22(LED2)P21(LED1)P20(LED0)
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OII
I/OI/OIO-
I/OI/OI/OI/OI/OI/OI/OI/O
Port6 / A-D converter input
Port5 / Interrupt inputPort5 / PWM outputPort5 / Timer YPort5 / Timer XPort5 / Serial readyPort5 / Serial clockPort5 / Serial outputPort5 / Serial inputPort4 / Serial ready / Timer Z functionPort4 / Serial clockPort4 / Transmit dataPort4 / Receive data
Port4 / Interrupt input
GroundReset inputPort4 / Interrupt input / Sub-clock generating inputPort4 / Interrupt input / Sub-clock generating outputClock inputClock outputGround
Port2
3334353637383940414243444546474849505152535455565758596061626364
P17P16P15P14P13P12
P11/INT01P10/INT41P07/AN15P06/AN14P05/AN13P04/AN12P03/AN11P02/AN10P01/AN9P00/AN8P37/SRDY3P36/SCLK3P35/TXD3P34/RXD3P33/SCLP32/SDAP31/DA2P30/DA1
VCCVREFAVSS
P67/AN7P66/AN6P65/AN5P64/AN4P63/AN3
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/OI/O-II
I/OI/OI/OI/OI/O
Port1
Port1 / Interrupt input
Port0 / A-D converter input
Port3 / Serial readyPort3 / Serial clockPort3 / Transmit dataPort3 / Receive dataPort3 / Serial clockPort3 / Serial data
Port3 / D-A converter output
Power supply +5VReference voltageAnalog ground
Port6 / A-D converter input
M38044M4-C16FPU0 (X4406100) CPU (LED DRIVER/SWITCH SCAN) PN: IC1
-
43
DDK-7
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899
100101102103104105
OUTERNO.
E5D4C3B2A1D5E6C4B3A2A3D6E7C5B4A4D7C6E8D8B5A5C7B6E9D9C8A6B7A7
E10D10
C9B8A8B9
E11D11C10
A9B10A10E12D12C11B11A11C12B12E13D13C13A12B13A13A14E14D14C14B14B15C15D15E15A15A16B16C16D16E16A17B17A18C17D17E17B18A19C18B19D18E18C19A20B20C20D19E19A21B21A22D20C21E20D21B22A23C22B23E21D22C23A24B24A25
VSS2VDDCCD15CD13CD14CD6CD2CD9CD11CD12CD10CD1VSSCD5CD8CD7
VSS2CD0VSS
VDDSCD4CD3CA2CA0CA8CA9CA5CA1CA3CA4
VSS2VDDCCA10CA6CA7CA11CA14CA15CA13CA12CSN0CSN1VSS
VDDSWRNRDN
WAIT0IRQ0
DREQ0TCK
TRSTVSSXOXI
VDDSSLAVETMSTDOICN
RFCLK0PLL_TSTN
PLL_BPVDDSVSS
RFCLK1VDDC
TMODEPLL_AVD
NCNC
PLL_AVSTEST1VSSSY1
VDDCVSS2
KONTRG0KONTRG1
CK512CK128BCLKSY0
HMA20HMA21HMA19HMA18VDDSVSS
HMA9HMA7HMA6HMA8HMA10HMA17VDDSHMA11HMA4HMA5HMA13
VSSHMA12HMA3HMA14HMA2HMA1
--
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/O-
I/OI/OI/O-
I/O--
I/OI/OIIIIIIII--IIIIIIIIII--IIOOOII-OI-IIOIOII--I-I----I-I--OIOOOOOOOO--OOOOOO-OOOO-OOOOO
GroundPower supply +1.5 V
Data bus of internal register
Ground
Data bus of internal register
GroundData bus of internal registerGroundPower supply +3 V
Data bus of internal register
Address bus of internal regisuter
GroundPower supply +1.5 V
Address bus of internal regisuter
Chip select
GroundPower supply +3 VWrite strobeRead strobeHardware wait requestInterrupt request
Test pin
GroundCrystal osc. outputCrystal osc. inputPower supply +3 VMaster/Slave select
Test pin
Initial clearPLL ClockPower supply
Power supply +3 VGroundPLL ClockPower supply +1.5 VTest pinPower supply (PLL)Not usedNot usedPower supply (PLL)Test pinGroundSync. clockPower supply +1.5 VGround
Key on data
Master clock (256 Fs)Master clock (64 Fs)Sync. clock
Wave memory address bus
Power supply +1.5 VGround
Wave memory address bus
Power supply +1.5 V
Wave memory address bus
Ground
Wave memory address bus
106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210
OUTERNO.E22D23C24B25A26E23F22D24C25B26C26F23G22E24D25D26G23F24H22H23E25E26G24F25J22J23H24F26G25G26K22K23J24H25H26J25L22L23K24J26K25K26M22M23L24L25L26M24M25N22N23N24M26N25N26P26P22P23P24P25R25R24R23R22R26T26T25T24T23T22U26U25V26U24U23U22V25W26V24W25V23V22W24Y26Y25Y24W23W22AA26AA25AB26Y23
AA24Y22
AA23AB25AC26AB24AC25AA22AB23AC24AD26AD25AE26
VSS2VDDCHMA15HMA16HMA22HMA25VDDSHMA27HMA0HMA23HMA24VDDSHMA26HMA30HMA28HMA29LMA17LMA19
VSSVDDSLMA20LMA21LMA9LMA18LMA12LMA4LMA6LMA8LMA7LMA10VSS2VDDCLMA13LMA11LMA5LMA3LMA16LMA0LMA2LMA14LMA15LMA1VSS
VDDSLMA22LMA23LMA24LMA27LMA28LMA25LMA26LMA30LMA29MOENMWENLMD15
VSSVDDSLMD13LMD14LMD11LMD10VDDSVSS
LMD12LMD9LMD8LMD7VSS2VSS
LMD6LMD5LMD3LMD4VDDCVSS2LMD2LMD0LMD1
DCSL0VDDSVDDCDCSL1DQML3DQML1DMAL14
VDDSVSS
DMAL13DMAL12DMAL9
VSSDMAL11
VSSDMAL10DMAL8DMAL6DMAL7DMAL5VSS2VSS
DMAL4DMAL3DMAL2DMAL0
--OOOO-OOOO-OOOOOO--OOOOOOOOOO--OOOOOOOOOO--OOOOOOOOOOOI/O--
I/OI/OI/OI/O--
I/OI/OI/OI/O--
I/OI/OI/OI/O--
I/OI/OI/OO--OOOO--OOO-O-OOOOO--OOOO
GroundPower supply +1.5 V
Wave memory address bus
Power supply +3 V
Wave memory address bus
Power supply +3 V
Wave memory address bus
Wave memory address bus (Lower data memory)
GroundPower supply +3 V
Wave memory address bus (Lower data memory)
GroundPower supply +1.5 V
Wave memory address bus (Lower data memory)
GroundPower supply +3 V
Wave memory address bus (Lower data memory)
Wave memory output enableWave memory write enableWave memory data bus (Lower 16 bit)GroundPower supply +3 V
Wave memory data bus (Lower 16 bit)
Power supply +3 VGround
Wave memory data bus (Lower 16 bit)
GroundGround
Wave memory data bus (Lower 16 bit)
Power supply +3 VGround
Wave memory data bus (Lower 16 bit)
Power supply +3 VPower supply +1.5 V
MASK signal
Address bus (DIMM, SDRAM)Power supply +3 VGround
Address bus (DIMM, SDRAM)
GroundAddress bus (DIMM, SDRAM)Ground
Address bus (DIMM, SDRAM)
GroundGround
Address bus (DIMM, SDRAM)
T8F02TB-0102 (X0060A00) SWP50 (Tone Generator) TG1-E1: IC006, TG1-E2: IC006,TG2A (TG2): IC002, IC003
-
DDK-7
44
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312303314315
VSS2VDDCDMAL1DCSL2DRAS0DCAS0VDDS
DCLKINDQML2DCSL3DQML0VDDSVSS
DWEN0DCLK0DCLK1DCLKEHMD13
VSSVDDS
HMD15HMD14HMD10HMD12VDDCVDDSHMD7HMD11HMD9HMD8VSS2VDDCHMD4HMD6HMD5HMD3VSS
VSS2HMD1HMD2HMD0
DCSH0VSS
VDDSDCSH1DQMH3DQMH1DMAH14DMAH13
VSSVSS2
DMAH11DMAH12DMAH10DMAH9DMAH8VDDSVDDS
DMAH6DMAH7DMAH4DMAH3VDDSVSS
DMAH5DMAH2DMAH1DMAH0
VSSVSS
DRAS1DCSH2DQMH2DCSH3VDDCVSS2
DQMH0DWEN1DCAS1DCLK2VDDSVDDCDCLK3MELO0MELO1MELO2VDDSVSS
MELO3MELO4MELO5MELO6MELO7WCLK0WCLK1EIRQEICNESDAESCLMELI0MELI1MELI2MELI3MELI4MELI5
--OOOO-IOOO--OOOOI/O--
I/OI/OI/OI/O--
I/OI/OI/OI/O--
I/OI/OI/OI/O--
I/OI/OI/OO--OOOOO--OOOOO--OOOO--OOOO--OOOO--OOOO--OOOO--OOOOOOOOOI/OI/OIIIIII
GroundPower supply +1.5 VAddress bus (DIMM, SDRAM)
Power supply +3 V
MASK signal
MASK signalPower supply +3 VGround
Wave memory data bus (Upper data memory)GroundPower supply +3 V
Wave memory data bus (Upper data memory)
Power supply +1.5 VPower supply +3 V
Wave memory data bus (Upper data memory)
GroundPower supply +1.5 V
Wave memory data bus (Upper data memory)
GroundGround
Wave memory data bus (Upper data memory)
GroundPower supply +3 V
MASK signal
Address bus (DIMM, SDRAM)
GroundGround
Address bus (DIMM, SDRAM)
Power supply +3 VPower supply +3 V
Address bus (DIMM, SDRAM)
Power supply +1.5 VGround
Address bus (DIMM, SDRAM)
GroundGround
MASK signal
Power supply +1.5 VGroundMASK signal
Power supply +3 VPower supply +1.5 V
MEL wave data output
Ground
MEL wave data output
For DAC LR clock
MEL wave data input
316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380381382383384385386387388389390391392393394395396397398399400401402403404405406407408409410411412413414415416417418419420
OUTERNO.
OUTERNO.
AB22AC23AD24AE25AF26AC22AB21AD23AE24AF25AF24AC21AB20AD22AE23AF23AC20AD21AB19AC19AE22AF22AD20AE21AB18AC18AD19AF21AE20AF20AB17AC17AD18AE19AF19AE18AB16AC16AD17AF18AE17AF17AB15AC15AD16AE16AF16AD15AE15AB14AC14AD14AF15AE14AF14AF13AB13AC13AD13AE13AE12AD12AC12AB12AF12AF11AE11AD11AC11AB11AF10AE10AF9
AD10AC10AB10AE9AF8AD9AE8AC9AB9AD8AF7AE7AD7AC8AB8AF6AE6AF5AC7AD6AB7AC6AE5AF4AD5AE4AB6AC5AD4AF3AE3AF2
AB5AC4AD3AE2AF1AB4AA5AC3AD2AE1AD1AA4
Y5AB3AC2AC1
Y4AA3W5W4
AB2AB1
Y3AA2
V5V4W3
AA1Y2Y1U5U4V3W2W1V2T5T4U3V1U2U1R5R4T3T2T1R3R2P5P4P3R1P2P1N1N5N4N3N2M2M3M4M5M1L1L2L3L4L5K1K2J1K3K4K5J2H1J3H2J4J5H3G1G2G3H4H5F1F2E1G4F3G5F4E2D1E3D2F5E4D3C1C2B1
VSS2VDDCMELI6MELI7ADLRDITOVSS
AFRMACLKADIR
ADAT0VDDSADAT9ADAT3ADAT1ADAT2
ADAT10ADAT6
VSSVDDSADAT4ADAT5ADAT11ADAT7
ADAT14ADAT15ADAT13ADAT8
ADAT12TDI
VSS2VDDCHRD13HRD15HRD14HRD12HRD7HRD6HRD10HRD11HRD9HRD8VSS
VDDSHRD5HRD4HRD3HRD2HRD1VDDSHRD0RWENRQMLRCASRRASRA13VDDSVDDSRA10RA12RA1RA2
VDDSVSSRA0RA3RA4RA5
VSS2VSSRA6RA7RA9RA8
VDDCVSS2RA11RCLK
RCLKERCLKINVDDSVDDCRQMHLRD15LRD14LRD13VDDSVSS
LRD12LRD11LRD8VDDSLRD10VDDSLRD9LRD7LRD5LRD6LRD4VSS2VSSLRD3LRD2LRD1LRD0
--IIOO-
I/OI/OOI/O-
I/OI/OI/OI/OI/OI/O--
I/OI/OI/OI/OI/OI/OI/OI/OI/OI--
I/OI/OI/OI/OI/OI/OI/OI/OI/OI/O--
I/OI/OI/OI/OI/O-
I/OOOOOO--OOOO--OOOO--OOOO--OOOI--OI/OI/OI/O--
I/OI/OI/O-
I/O-
I/OI/OI/OI/OI/O--
I/OI/OI/OI/O
GroundPower supply +1.5 V
MEL wave data input
Power supply +3 V
Ground
Data bus (ABUS)Power supply +3 V
Data bus (ABUS)
GroundPower supply +3 V
Data bus (ABUS)
GroundPower supply +1.5 V
DRAM data bus
GroundPower supply +3 V
DRAM data bus
Power supply +3 VDRAM data busDRAM write enable
DRAM column address strobe (RAS signal)DRAM row address strobe (RAS signal)DRAM address busPower supply +3 VPower supply +3 V
DRAM address bus
Power supply +3 VGround
DRAM address bus
GroundGround
DRAM address bus
Power supply +1.5 VGroundDRAM address bus
Power supply +3 VPower supply +1.5 V
DRAM data bus (Lower data)
Power supply +3 VGround
DRAM data bus (Lower data)
GroundDRAM data bus (Lower data)Ground
DRAM data bus (Lower data)
GroundGround
DRAM data bus (Lower data)
TG1-E1: IC006, TG1-E2: IC006, TG2-E1: IC002, IC003
-
45
DDK-7
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
101112131415161718192021222324
D4VCCD5D6
GNDD7D8VCCD9
D10GNDD11D12NCD13D14GNDD15D16D17VCCD18D19GND
I/O-
I/OI/O-
I/OI/O-
I/OI/O-
I/OI/O
I/OI/O-
I/OI/OI/O-
I/OI/O-
Data busPower supply
Data bus
Ground
Data bus
Power supply
Data bus
Ground
Data bus
Not used
Data bus
Ground
Data bus
Power supply
Data bus
Ground
252627282930313233343536373839404142434445464748
D20CLKINSHTDN
PLLGNDPLLVCCPLLGNDLVDSGNDCLKOUTPCLKOUTM
Y2PY2M
LVDSGNDLVDSVCC
Y1PY1MY0PY0M
LVDSGNDNCD0D1
GNDD2D3
I/OI
----OO
--
-
I/OI/O-
I/OI/O
Data busInput clock for CLKIN MIDI
GroundPower supply
Goround
Clock output
GroundPower supply
GroundNot used
Data bus
Ground
Data bus
DM2: IC013SN75LVDS84ADGGR (X4212A00) LVDS TRANSMITTERS
PINNO. I/O FUNCTIONNAME
PINNO. I/O FUNCTIONNAME
123456789
101112131415161718192021222324
D5D6D7
/IRQ0/IRQ1Vss
/IRQ2IRQ3/RD/WR/CE
/ASTBTESTSIO
RX0TX0RX1TX1VssVddRX2
TX2/BO2RX30TX30TX31
I/OI/OI/OI/OI/O
I/OI/OIIIIIIOIO
IOIOI
Data Bus
Interrupt Request Port 0Interrupt Request Port 1GroundInterrupt Request Port 2Interrupt Request Port 3Read Signal InputWrite Signal InputChip Enable InputAddress Strobe (Not used: to ground)Input with Pull-down Resistor (50k)Receive Data 0Transmit Data 0Receive Data 1Transmit Data 1GroundPower SupplyReceive Data 2Transmit Data 2Receive Data 30Transmit Data 30Receive Data 31
252627282930313233343536373839404142434445464748
TX31RX32TX32RX33TX33
/ICVssXI
VssXOA0A1A2A3A4A5
CPUCLKVssVddD0D1D2D3D4
OIOI
I/OI
I
I/OIIIIIII
I/OI/OI/OI/OI/O
Transmit Data 31Receive Data 32Transmit Data 32Receive Data 33Transmit Data 33Initial ClearGroundQuartz Crystal InputGroundQuartz Crystal Output
Address Bus
CPU ClockGroundPower Supply
Data Bus
MBCG46183-129 (XV833A00) Gate Array DM2: IC060
-
DDK-7
46
SN74AHCT04NSR (X3681A00)74VHCT04ASJX NL (X3682A00)TC74VHCT04AF E,F,K (XT777B00)DJK : IC201
Hex Inverter
1
2
3
4
5
6
7
1A
1Y
2A
2Y
3A
3Y
Vss
14
13
12
11
10
9
8
VDD
6A
6Y
5A
5Y
4A
4Y
SN74LVC08APWR (X3019A00)HD74LVC08TELL (X4961A00)DM2 : IC032, IC033
Quad 2 Input AND
1
2
3
1A
1Y
42A
52B
62Y
7VSS
1B
14
13
12
VDD
4A
11 4Y
10 3B