UNIVERSITI PUTRA MALAYSIA
OPTICAL PERMITTIVITY OF ALIPHATIC ALCOHOLS, POLYETHYLENE GLYCOLS AND DYE SOLUTIONS USING THE SURFACE PLASMON
RESONANCE TECHNIQUE
NURUL IZRINI BINTI IKHSAN
FS 2009 14
OPTICAL PERMITTIVITY OF ALIPHATIC ALCOHOLS, POLYETHYLENE GLYCOLS AND DYE SOLUTIONS USING THE SURFACE PLASMON
RESONANCE TECHNIQUE
By
NURUL IZRINI BINTI IKHSAN
Thesis submitted to the School of Graduate Studies, Universiti Putra Malaysia, in Fulfillment of the Requirements for the Degree of Master of Science
April 2009
Specially Dedicated to:
My beloved parents; Ikhsan B. Sarpin & Esah Bt Ahmad
For their love, support and concern ....
My dearest fiance; Amir Hafiz lzzudin B. Amir Sharifuddin
For his love, understanding, patience and care ...
My Bro' and Sis' in-law; Mohd Darul Idzuar & Zaliha
My cutely niece & nephew; Nurdzania Batrisyia & Syahmi Haiman
My supervisor; Prof Dr. W. Mahmood Mat Yunus
For his encouragement, guidance and advice ...
And all my friends ...
Abstract of thesis presented to the Senate of Universiti Putra Malaysia in fulfillment of the requirement for the degree of Master of Science
OPTICAL PERMITTIVITY OF ALIPHATIC ALCOHOLS, POLYETHYLENE GLYCOLS AND DYE SOLUTIONS USING THE SURFACE PLASMON
RESONANCE TECHNIQUE
By
NURUL IZRINI IKHSAN
April 2009
Chairman : Professor W. Mahmood Mat Yunus, PhD
Faculty : Science
Surface plasmon is a charge density wave that occurs at an interface between a thin
metal film and dielectric medium. The most common means of excitation surface
plasmon resonance is achieved through the Kretschmann configuration by utilizing the
attenuated total reflection (ATR).
In this study, gold with purity 99.99% was deposited onto glass cover slip in a form of
thin film (thickness � 50 nm) using sputtering technique which then coupled onto one
surface of 60° prism using index matching oil. Liquid samples used as the dielectric
medium were aliphatic alcohols; (methanol, ethanol and 1-propanol), polyethylene
glycols (PEG) series; (PEG 400, PEG 4000, PEG 1 0000 and PEG 20000) and dye
solutions; (methylene blue, rhodamine B and rhodamine 6G). The intensity of the optical
reflectivity was measured as a function of incident angle at the metal and dielectric
interface.
The determination of the dielectric constant 6r and 6; for metal and liquid was carried
out by fitting the experimental data to the theory using Fresnel Equation. It was found
that the permittivity values of 6r and 6; for aliphatic alcohol, polyethylene glycols and
dye solutions are linearly proportional to the concentration. The value of the real part of
dielectric constant, 6r is in the range of 1.767 to 1.811 while the imaginary part, 6; is in
the range of 2 x 10-4 to 6 x 10-2•
In the case of resonance angle shift, the resonance angle increased with the increasing of
the concentration. The shift in resonance angle (!!.(}) varies linearly with the
concentration. Since the straight line passes through the origin, it is possible to use SPR
technique for the detection of aliphatic alcohols, polyethylene glycols and dyes at very
low concentration. The slopes of the straight lines represented the sensitivity of the
detection. The large value of sensor sensitivity of 452.763°/(mollL) is obtained for the
methylene blue sample.
The kinetic behaviour of the system was also investigated by examining the self
assembling process on the metal surface in real time. The shift in resonance angle
increased rapidly with time due to the immobilization of the molecules deposited on the
gold thin film surface. For aliphatic alcohol solution at concentration of 0.100 mollL,
ethanol achieved a plateau region faster as compared to methanol and I-propanol. For
11
PEG samples at a concentration of 5.5 %w/w, PEG 400 responded faster as compared to
PEG 4000, PEG 10000 and PEG 20000 while for dye sample at concentration of 0.010 mollL, rhodamine 6G responded faster as compared to both rhodamine B and methylene
blue.
The experimental results of surface plasmon resonance show that the optical properties
and the kinetic behaviour can be determined by using the surface plasmon resonance
phenomenon. This works shows that this technique can be a good chemical optical
sensor where is suitable to study molecule-dielectric interaction for aliphatic alcohols,
polyethylene glycols series and dye solutions in water.
iii
Abstrak tesis yang dikemukakan kepada Senat Universiti Putra Malaysia sebagai memenuhi keperluan untuk Ijazah Master Sains
PERMITIVITI OPTIK TERHADAP LARUT AN ALKOHOL ALIFATIK , POLIETILENA GLIKOL DAN BAHAN PEW ARNA MENGGUNAKAN
TEKNIK RESONANS PLASMON PERMUKAAN
Pengerusi
Fakulti
Oleh
NURUL IZRINI IKHSAN
April 2009
: Professor W. Mahmood Mat Yunus, PhD
: Sains
Plasmon permukaan ialah gelombang ketumpatan caj yang berlaku pada permukaan di
antara filem tipis logam dan medium dielektrik. Cara yang paling biasa bagi meransang
resonans plasmon permukaan boleh dicapai melalui konfigurasi Kretschmann dengan
menggunakan pengecilan pantulan dalaman penuh (ATR)
Dalam kajian ini, emas dengan ketulenan 99.99% telah disaputkan di atas slip kaca
dalam bentuk filem tipis (ketebalan -50 nm) menggunakan teknik percikan, di mana
kemudian dilekatkan kepada satu permukaan prisma 60° dengan menggunakan min yak
indeks sepadan. Sampel cecair yang digunakan sebagai medium dielektrik ialah alkohol
alifatik; (metanol, etanol dan I-propanol), siri polietilena glikol (PEG); (PEG 400, PEG
4000, PEG 10000 dan PEG 20000) dan larutan bahan pewarna (metilin biru, rodamin B
dan rodamin 6G. Eksperimen telah dilakukan dengan mengukur keamatan keterpantulan
IV
optik sebagai satu fungsi kepada sudut tuju pada pennukaan Iogam dan dielektrik.
Penentuan pemalar dielektrik &r dan &j bagi Iogam dan cecair telah dilakukan dengan
memadankan data eksperimen kepada teori menggunakan persamaan Fresnel. Didapati
bahawa nilai permitiviti &r dan &j bagi larutan alkohol alifatik, polietilena gIikol dan
bahan pewama adalah berkadar terus kepada kepekatan. Nilai bahagian nyata bagi
pemalar dielektrik &r adalah di dalam julat 1 .767 ke 1.811 manakala bagi bahagian
khayal &j adalah di dalam julat 2 x 10-4 ke 6 x 10-2•
Dalam kes anjakan sudut resonans, sudut resonans meningkat dengan pertambahan
kepekatan. Anjakan sudut resonans (tJ,() berubah secara linear dengan kepekatan. OIeh
kerana garis lurus melalui asalan, teknik SPR ini boleh digunakan untuk mengesan
alifatik alkohol, polietilena glikol dan bahan pewama pada kepekatan yang sangat
rendah. Kecerunan pada garis lurus mewakili kepekaan pengesanan. Kepekaan pengesan
tertinggi adalah pada 452.76°/(mol/L) telah diperolehi pada sample metilin bim.
Perlakuan kinetik sistem juga telah diperiksa dengan memerhatikan proses berkumpul
kendiri pada permukaan logam dalam masa nyata. Anjakan sudut resonans meningkat
secara mendadak dengan masa yang mana berkaitan dengan endapan molekul pada
pennukaan filem tipis emas. Bagi larutan alkohol alifatik pada kepekatan 0.100 mollL,
etanol telah mencapai bahagian dataran tinggi lebih cepat berbanding dengan masing
masing metanol, dan I-propanol. Bagi sampel-sampel PEG pada kepekatan 5.5 %w/w,
PEG 400 bertindak balas lebih cepat berbanding PEG 4000, PEG 10000 dan PEG 20000
v
manakala untuk sampel bahan pewama pada kepekatan 0.01 0 mollL, rodamin 60
bertindak balas lebih cepat berbanding kedua-dua rodamin B dan metilin biro.
Keputusan eksperimen untuk resonans plasmon permukaan menunjukkan bahawa sifat
sifat optik dan perlakuan kinetik dapat ditentukan menggunakan fenomena plasmon
permukaan. Teknik iill telah terbukti boleh dijadikan sebagai pengesan optik kimia yang
berkesan yang sesuai untuk mengkaji tindak balas molekul-dielektrik pada larutan
alkohol alifatik, polietilena glikol dan bahan pewama di dalam air.
vi
ACKNOWLEDGEMENT
In the name of Allah, Most Gracious, Most Merciful ...
Thank. you ALLAH for providing me the strength and patience to complete this
project efficiently. First of all, I would like to express my sincere gratitude and thanks
especially to my project supervisor, Prof. Dr. W. Mahmood Mat Yunus for his
invaluable advice patience and constructive criticism during the preparation of this
master research project. Without his persistent assistance and exceptional generosity,
this work would not have been possible.
I wish to acknowledge my indebtedness to Assoc. Prof. Dr. Zainal Abidin Talib
and Assoc. Prof. Dr. Zaidan Abdul Wahab as my co-supervisors for their concern in my
project. Special thanks to Pn. Wan Yusmawati Wan Yusuf for her help and cooperation
to complete my work and also the willingness to share her precious experience with me.
Credit is also due to all the lecturers and technical staffs in the Department of Physics,
Faculty of Science, Universiti Putra Malaysia and my entire friends who have directly or
indirectly had offered me a helping hand.
Grateful thanks to my dearest parents and family members who never fail to be
there for their attention, loves and prayers and also for their understanding and supports
throughout this research project.
vii
I certify that a Thesis Examination Committee has met on 2 April 2009 to conduct the final examination of Nurul Izrini binti Ikhsan on her thesis entitled "Optical Permittivity of Aliphatic Alcohols, Polyethylene Glycols and Dye Solutions Using the Surface Plasmon Resonance Technique" in accordance with the Universities and University Colleges Act 1971 and the Constitution of the Universiti Putra Malaysia [P.U.(A) 106] 15 March 1998. The Committee recommends that the student be awarded the Master of Science.
Members of the Thesis Examination Committee were as follows:
Khaida Khalid, PhD Professor Faculty of Science Universiti Putra Malaysia (Chairman)
Maarof H. A. Moksin, PhD Professor Faculty of Science Universiti Putra Malaysia (Internal Examiner)
Abdul Halim Shaari, PhD Professor Faculty of Science Universiti Putra Malaysia (Internal Examiner)
Roslan Abd. Shukor, PhD Professor F acuIty of Sciences and Technology Universiti Kebangsaan Malaysia (External Examiner)
MHUAT, PhD Professor an Deputy Dean School of G aduate Studies Universiti Putra Malaysia
Date: 21 May 2009
VIII
This thesis was submitted to the Senate of Universiti Putra Malaysia and has been accepted as fulfillment of the requirement for the degree of Master of Science. The members of the Supervisory Committee were as follows:
W. Mahmood Mat Yunus, PhD. Professor Faculty of Science Universiti Putra Malaysia (Chairman)
Zainal Abidin Talib, PhD. Associate Professor Faculty of Science Universiti Putra Malaysia (Member)
Zaidan Abdul Wahab, PhD. Associate Professor Faculty of Science Universiti Putra Malaysia (Member)
D GHAZALI, PhD Professor and Dean School of Graduate Studies Universiti Putra Malaysia
Date: 8 June 2009
IX
DECLARATION
I declare that the thesis is my original work except for quotations and citations which have been duly acknowledged. I also declare that it has not been previously, and is not concurrently, submitted for any other degree at Universiti Putra Malaysia or at any other institution
&5kL. NURUL IZRINI IKHSAN
Date: 23/ r, I 001
x
TABLE OF CONTENTS
Page
ABSTRACT I ABSTRAK IV ACKNOWLEDGEMENT vii APPROVAL Vl11 DECLARATION x LIST OF TABLES xiv FIGURE CAPTIONS XIV LIST OF ABBREVIATIONS XIX
CHAPTER
1. INTRODUCTION 1.1 Surface Plasmon Resonance 2
1.1.1 Attenuated Total Reflection 2 1.1.2 Surface Plasmons 2 1.1.3 Momentum Resonance 3 1.1.4 Evanescent Wave 4 1.1.5 SPR Dependencies 5
1.2 Sample Background 1.2.1 Aliphatic Alcohols 6 1.2.2 Polyethylene Glycol Series 7 1.2.3 Dye Solution 8
1.3 Advantages From the Surface Plasmon Resonance Study 9
1.4 Application of Surface Plasmon Resonance 9 1.5 Objective of the Research 10 1.6 Outline of the Thesis 11
2. LITERATURE REVIEW 2.1.1 Detection Characteristics of Surface Plasmon
Resonance Technique 12 2.2 Surface Plasmon Resonance as an Optical Sensor 14 2.3 Metal Surface 16 2.4 Vapour as a Dielectric Medium 18
3. THEORY 3.1 Surface Plasmon Resonance 20 3.2 Surface Electromagnetic Waves 21 3.3 Scattering Linkage of Surface Plasmon Resonance 24 3.4 Angle Dependence of the Reflectivity of Surface
Plasmon resonance 27
Xl
3.5 Excitation of Surface Plasmons Using Prism Coupling 29 3.5.1 Kretshmann Configuration 29 3.5.2 Otto Configuration 30
4. METHODOLOGY 4.1 Sample Preparation 32 4.2 Substrate Cleaning 32 4.3 Thin Metal Film Preparation 33 4.4 Sample Preparation 33
4.4.1 Aliphatic Alcohol Solutions 34 4.4.2 Polyethylene Glycol (PEG) Solution 34 4.4.3 Dye Solution 35
4.5 Experimental Setup 35 4.5.1 Sample Cell 36
4.6 Experimental Procedure 37 4.7 Fitting Experimental Data to the Theoretical Data 38
5. RESULTS AND DISCUSSION 5.1 Introduction 39 5.2 Stability of Gold Surface as the Active Layer for
Surface Plasmon Technique 39 5.3 Effect of Gold Thin Film Thickness 43
5.4 Measurement of Optical Constant, Gr and Gi of
Dielectric Medium 48 5.4.1 Introduction 48 5.4.2 Aliphatic Alcohol 50 5.4.3 Polyethylene Glycol 54 5.4.4 Dye 60
5.5 Sensitivity of Surface Plasmon Resonance 65 5.5.1 Aliphatic Alcohol 65 5.5.2 Polyethylene Glycol 68 5.5.3 Dye 70
5.6 Kinetic Behaviour of Self-Assembly 73 5.6.1 Aliphatic Alcohol 74 5.6.2 Polyethylene Glycol 81 5.6.3 Dye 88
6. CONCLUSION 6.1 Conclusion 96 6.2 Suggestion 99
REFERENCES 100 APPENDIX 104 BIODATA OF STUDENT 118 LIST OF PUBLICATIONS 119
XlI
LIST OF TABLE
TABLE
5.1
5.2
5.2
List of optical properties cr and ci for aliphatic alcohol
at concentration of 0.06 mollL
List of optical properties £r and Sj for PEG 400, PEG 4000, PEG 1000 and PEG 20000 at concentration of 3.5 %w/w
List of optical properties cr and ci for dye at concentration
of 0.006 mollL
FIGURE CAPTIONS
FIGURE
3.1
3.2
3.3
3.4
4.1
4.2
5.1
Surface electromagnetic wave at the interface
with dielectric function of c) and c2
Kretschrnann configuration for excitation of surface plasmon resonance, dielectric constants and film thickness.
Kretschrnann geometry of the attenuated total reflection (ATR) method
Otto geometry of the attenuated total reflection (ATR) method
Experimental setup for Surface Plasmon Resonance Technique
The construction of the cell in Surface Plsmon Resonance Measurement
The variation of surface plasmon resonance curve for gold exposed only to air from day 1 to day 10
PAGE
51
57
62
PAGE
22
28
30
31
36
37
41
xiii
5.2 The fitting line for experimental data of gold (dot) as compared to the theoretical (line) graph 41
5.3 The dielectric constant as a function of time for gold sample 42
5.4 The Reflectance as a function of incidence angle for different thickness of gold films 44
5.5 The SPR angle 9spr as a function of gold film thickness 45
5.6 The minimum reflectance values as a function of gold film thickness 45
5.6 The variation of dielectric constant, Er and Sj with the thickness of gold film 47
5.7 The reflectivity versus incidence angle for distilled water. The solid line represents the theoretical curve. 49
5.8 The reflectance curve for distilled water, ethanol, methanol and I-propanol at 0.06 mollL 51
5.10 The reflectivity versus incidence angle for prism! gold/methanol combination. Solid line is the theoretical curve. 52
5.11 The real part of dielectric constant, Er as a function of aliphatic alcohols concentration. 53
5.12 The imaginary part of dielectric constant, Sj as a function of aliphatic alcohols concentration 54
5.13 Resonance curves for gold/air, gold/distilled water and gold/PEG solution 55
5.14 Reflectance curve for distilled water PEG 400, PEG 4000, PEG 10000 and PEG 20000 at 3.5 %w/w 56
5.15 The reflectivity versus incidence angle for prism/gold! PEG 400 combination. The solid line represents the theoretical curve. 58
5.16 The real part of dielectric constant, Er as a function of polyethylene glycol series concentration 58
XIV
5.17 The imaginary part of dielectric constant, Ej as a function of polyethylene glycol series concentration 59
5.18 The resonance curves for gold!air, gold!distilled water and gold!dye solution 60
5.19 Reflectance curve for distilled water rhodamine B, rhodamine 6G and methylene blue at concentration of 0.006 moVL 61
5.20 The reflectivity versus incidence angle for prism/gold! Rhodamine B combination. The solid line represents the theoretical curve. 62
5.21 The real part of dielectric constant, Er as a function of dye concentration 63
5.22 The imaginary part of dielectric constant, Ej as a function of dye concentration 64
5.23 Optical reflectance as a function of incidence angle for Methanol at various concentrations 67
5.24 The shift of resonance angle versus concentration for aliphatic alcohols at various concentrations 67
5.25 The optical reflectance as a function of incidence angle for PEG 20000 at various concentrations 69
5.26 The shift of resonance angle versus concentration for polyethylene glycol series at various concentrations 70
5.27 Optical reflectance as a function of incidence angle of methylene blue at various concentrations 71
5.28 The shift of resonance angle versus concentration for dye at various concentrations 72
5.29 The resonance angle of distilled water versus time 74
5.30 The shift of resonance angle versus time for methanol, ethanol and 1- propanol at concentration of 0.100 mollL 75
5.31 The shift of resonance angle versus time for (a) methanol, (b) ethanol and (c) I -propanol at four different concentrations 78
xv
5.32
5.33
5.34
5.35
5.36
5.37
5.38
5.39
5.40
5.41
5.42
5.43
5.44
Stretching Coefficient, f3 versus concentration for Methanol,Ethanol and I-propanol.
Saturated resonance angle, 110 <fJ versus concentration
for Methanol, Ethanol and I-propanol
Time constant, t versus concentration for Methanol, Ethanol and I-propanol
The shift of resonance angle versus time for PEG 400, PEG 4000, PEG 10000 and PEG 20000 at concentration of 5.5%w/w.
The shift of resonance angle versus time for (a) PEG 400, (b) PEG 4000 (c) PEG 10000 and (d) PEG 20000 at three different concentrations
Stretching Coefficient, f3 versus concentration for PEG 400, PEG 4000, PEG 10000 and PEG 20000
Saturation value, 110", versus concentration for
PEG 400, PEG 4000, PEG 10000 and PEG 20000
Time constant, t versus concentration for PEG 400, PEG 4000, PEG 10000 and PEG 20000
The shift of resonance angle versus time for methylene blue, rhodamine B and rhodamine 6G at concentration of 0.010 mol/L
The shift of resonance angle versus time for (a) Methylene Blue, (b) Rhodamine 6G and (c) Rhodamine B at three different concentrations
Stretching Coefficient, fJ versus concentration for methylene blue, rhodamine B and rhodamine 6G
Saturation value, 11000 versus concentration for
methylene blue, rhodamine B and rhodamine 6G
Time constant, t versus concentration for methylene blue, rhodamine B and rhodamine 6G
79
80
81
82
85
86
87
88
89
91
93
94
95
XVI
LIST OF ABBREVIATIONSINOTATION/GLOSSARY OF TERM
OJ Incidence angle
Bspr Surface Plasmon Resonance angle
!1B The shift of resonance angle
!1Bo The initial shift of resonance angle respect to distilled water
!1B 00 The saturated resonance angle
&r Real part of dielectric constant
&; Imaginary part of dielectric constant
&0 Dielectric constant of prism
&] Dielectric constant of metal film
&2 Dielectric constant of dielectric
I Wave field
f.l Magnetic permeability
n p Refractive index of prism
nm Refractive index of metal film
no Refractive index of dielectric medium
kx Wavevector component along surface electromagnetic wave
ksp Wavevector of a plasmon
K] Wavevector in media 1
K2 Wavevector in media 2
R Reflection coefficient
Rmin Reflectance minimum
10 Incidence light
I r Reflected light
A Wavelength
d Thickness
XVll
c Concentration
r Time constant
f3 Stretching coefficient
ATR Attenuated total reflection
Au Gold
Ag Silver
EO Ethylene oxide
MEG Mono ethylene glycol
MWR Molecular weight relative
PEG Polyethylene glycol
SPR Surface plasmon resonance
SPW Surface plasmon wave
SPs Surface plasmons
QCM Quartz Crystal Microbalance
M Concentration solution
V Volume of concentration
T Temperature
MoliL Mol per liter
%w/w Weight percent.
XVlll
CHAPTERl
INTRODUCTION
During the last two decades, we have remarkable research and development activity
intended at the realization of optical sensors for the measurement of chemical and
biological entities (Homola et aI., 1999). The first optical chemical sensors were based
on the measurement of changes in absorption spectrum and were developed for the
measurement of CO2 and 02 concentration (Brecht and Gauglitz, 1995). A large variety
of optical methods have been used in chemical sensors and biosensors including
ellipsometry, interferometer (white light interferometer), spectroscopy of guided modes
in optical waveguide structures (grating coupler) and surface plasmon resonance. The
chosen quantity is determined by measuring the refractive index, absorbance and
fluorescence properties of analyte molecules or a chemo-optical transducing medium
(Boisde and Harmer, 1996). The potential of surface plasmon resonance (SPR) for
characterization of thin films (Pockrand et al., 1978) and monitoring processes at metal
interfaces [Gordon and Ernst, 1980] was recognized in the late seventies. In 1982 the use
of SPR for gas detection and biosensing was demonstrated by Nylander et al. (1982)
and Liedberg et aI, (1983 and 1995). Since then SPR sensing has been receiving
continuously growing attention from scientific community. Development of SPR
sensing configurations as well as applications of SPR sensing devices for the
measurement of physical, chemical and biological quantities has been described by
Homola et al. (1999). In this area, SPR as a surface oriented method has shown a vast
potential for affinity biosensors and allowing real-time analysis of bio-specific
interactions without the use of labeled molecules.
1.1 Surface Plasmon Resonance (SPR)
SPR is an optical phenomenon occurs in thin metal film under condition of attenuated
total reflection (ATR). This phenomenon generates a sharp dip in the intensity of the
reflected light at a particular angle known as the resonant angle. This resonant angle
depends on numerous factors including the refractive index of the medium (refractive
index is directly interrelated to the concentration of dissolved material in the medium)
close to the non-illuminated side of the thin metal film. By keeping other factors
constant, SPR can be used to measure different concentration of molecules in the surface
layer of solution in contact with the sensor surface (gold layer).
1.1.1 Attenuated Total Reflection
When a light beam hits a prism, the light bends towards the plane of interface and
passing from denser prism to a less denser one. Varying the incidence angle (8) will
change the out corning light until a critical angle is achieved where all the incoming light
is reflected within the prism. This is known as attenuated total reflection (ATR).
1.1.2 Surface Plasmons
In most surface plasmon resonance study, gold is used because it gives a SPR signal at
suitable combinations of reflectance angle and wavelength. In addition, gold is
chemically inert to solutions and solutes typically used in biochemical contexts (Biacore
Ab, 1998). When the light is polarized with its electric field in the plane of incidence,
the field causes collective oscillation of the electrons in the metal layer where the energy
- 2-
of the metal surface coincide with the incident photon and the charge density wave . The
incident light is absorbed and the energy is transferred to the electrons which converted
into surface plasmons. Photon and electron behaviour can only be described when they
have either wave or particle properties. In agreement with the quantum theory, a
plasmon is the particle name of the electron density waves. Therefore, in an ATR
situation when the quantum energy of the photons is right, the photons are converted
into plasmons and leaving a 'gap' in the reflected light intensity.
1.1.3 Momentum Resonance
Like all other variation, the photon to plasmon transfonnation must preserve both
momentum and energy in the process. Plasmons have a characteristic momentum
defined by factors that include the nature of the conducting film and the properties of the
medium on either side of the film. Resonance occurs when the momentum of incoming
light is equivalent to the momentum of the plasmons (resonance momentum). The
momentum of the photons and plasmons can be described by a vector function with both
magnitude and direction. The relative magnitude of the components changes when the
angle or wavelength of the incident light changes. However, plasmons are restricted to
the plane of the gold film and for SPR it is only the vector component parallel to the
surface that matters. Therefore, the energy and the angle of incident light should be right
(light is polarized with its electric field in the plane of incidence) to fonn surface
plasmon resonance.
- 3 -
1.1.4 Evanescent Wave
In ATR, the reflected light generates an electric field on the opposite site of the
interface. The plasmons create a comparable field that extends into the medium on
either side of the film. This field is identified as the evanescent wave because the
amplitude of the wave decreases exponentially with increasing distance from the
interface surface and decaying over a distance of about one light wavelength (Nagata
and Handa, 2000). The dept of the evanescent wave which is useful for measurements is
within � 300 nm of the sensor surface. The wavelength of the evanescent field wave is
the same as that of the incident light. The energy of the evanescent wave is dissipated by
heat. The equations which describe how electric fields travel through a medium include
a term for the properties of the medium and for light. This term is recognized as the
refractive index. The light is seen as refracted because the photons have a different
velocity in different media. In the same way, the velocity (and therefore the momentum)
of the plasmons is changed when the composition of the medium changes. When the
momentum change, the angle of incident light at which the resonance occurs was also
changed and known as resonant angle or angular SPR (Markey, 1 999) and (Akimoto,
2000). Alternatively, at a fixed angle of incident light, the wavelength can be varied until
resonance occurs (Quinn, 2000). This is known as resonant wavelength SPR or spectral
SPR and is not widely used (Akimoto, 2000). A full wavelength spectrophotometer can
simultaneously observe the wavelength from 400 - 800 nm and is more accurate than
angle measurements.
- 4 -