Download - Synopsis Network
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 1/46
A
SUMMER TRAINING SYNOPSIS BASED
ON
“ Networking Technologies
And
Its Design and Implementation ”
AT
SUBMITTED TO: - SUBMITTED BY:-
DR. Afshar Alam (HOD) Name: Saba Wasim
HAMDARD UNIVERSITY, Class: B.Tech (IT)
NEW DELHI University Roll No.- 2007-311-030
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 2/46
ACKNOWLEDGEMENT
It is my pleasure to be indebted to various people, who directly or indirectly
contributed in the development of this work and who influenced my thinking
behavior, and acts during the course of study.
I express my sincere gratitude to DR.AFSHAR ALAM, worthy HOD for
providing me an opportunity to undergo summer training at HCL CDC
I am thankful to Mr AKHLIESH SINGH for his support, cooperation, and
motivation provided to me during the training for constant inspiration,
presence and blessings.
Lastly, I would like to thank the almighty and my parents for their moral
support and my friends with whom I shared my day-to-day experience and
received lots of suggestions that improved my quality of work.
SABA WASI
(Name of the student
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 3/46
DECLARATION
I, Saba Wasim, student of B.Tech(IT) 5th Semester, studying atHamdard University, Hamdard Nagar New Delhi, hereby declarethat the summer training report on “Networking Technologiesand Design” submitted to Hamdard University, Hamdard Nagaris the original work conducted by me.
The information and data given in the report is authentic to the
best of my knowledge.
This summer training report is not being submitted to any otherUniversity for award of any other Degree, Diploma and
Fellowship.
Saba Wasim
(Name of the student)
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 4/46
TABLE OF CONTENT
i Acknowledgement
ii Certificate
iii Table of Content
iv.About HCL CDC
Project Review
1. NETWORK TOPOLOGY 1. TYPES OF NETWORKS
2. PHYSICAL TOPOLOGY
3. LAYER-3 DEVICES
4. LAYER-2 DEVICES
5. LAYER-1 (PHYSICAL) DEVICES
6. LAN Solution
7. END-USER DEVICES
8. LOGICAL TOPOLOGY
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 5/46
9. IP ADDRESSING
10. INTRODUCTION TO ROUTER
11. VLANS (Virtual LANs)
Project Work
1. ADDRESSING INFORMATION OF LAYER-3 DEVICES
2. ADDRESSING INFORMATION OF LAYER-2 DEVICES
3. COMPLETE LOGICAL NETWORK TOPOLOGY
4. IP ADDRESSING STRUCTURE
5. IP ADDRESS CLASSES
6. SUBNETTING
7. SWITCHING
8. VIRTUAL LAN
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 6/46
9. SWITCH CONFIGURATION
10. ROUTING
11. ADDRESSING SCHEME
12. INTERNET CONNECTION
13. ISP LEVELS OF SERVICE
Result and Conclusions
Bibliography
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 7/46
About HCL CDC
As the training arm of HCL Infosystems, HCL Career DevelopmentCentre (CDC) carries forth a legacy of excellence spanning acrossmore than three decades. HCL CDC is an initiative that enablesindividuals and organisations to benefit from HCL's deep expertisein the IT space.
Among the fastest growing IT education brands in India, HCL CDCoffers a complete spectrum of quality training programs onsoftware, hardware, networking as well as global certifications inassociation with leading IT organisations worldwide.
Empowered with strategic alliances with leading IT organisations
in India and abroad, HCL CDC training solutions cater to diverseconsumer profiles including individuals, enterprises, academicinstitutions and Government enterprises
"We shall develop and Impart Industry relevant ICT Education tomeet the requirement of customers,Industry and society by
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 8/46
continually updating technology content and improving ourprocesses"
Certification of quality standards
"In its pursuit of excellence", the company has developed aquality management system in line with ISO 9001:2000standard
Network Design And Implmentation
At
HCL CDC
Project Review
NETWORK TOPOLOGY
A network is a system that transmits any combination of voice, videoand/or data between users. A network can be defined by itsgeographical dimensions and by which the user’s PC access it.
A network consists of a:
• The network operating system (Windows NT/2000TM /Xp) on
the user’s PC (client) and server.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 9/46
• The cables connecting all network devices (user’s PC, server,
peripherals, etc.).
• All supporting network components (hubs, routers and
switches, etc.).Computer Network means an interconnected collection of autonomous computers.
Requirement of NetworkingResource sharing- To make all programs, equipment, and especiallydata available to anyone on the network without regard to the physicallocation of the resource and the user.
High reliability- As all files could be replicated on two or three
machines, so if one of them is unavailable (due to hardware failure),the other copies could be used.
Scalability- It is the ability to increase system performance graduallyas the workload grows just by adding more processors.A computer network can provide a powerful communication mediumalong widely separated employees.
The use of networks to enhance human-to-human communication willprobably prove more important than technical goals such as improved
reliability.
These are the reasons that forced the inventerors to invent thenetworking devices, models and protocols etc.
And the birth of Networking took place in 1844 when for the first timeSamuel Morse send the first telegraph message.
TYPES OF NETWORKS
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 10/46
LOCAL AEA NETWORK (LAN)
A local area network (LAN) is a computer network covering a smallphysical area, like a home, office, or small groups of buildings, such as
a school, or an airport. The defining characteristics of LANs, in contrastto wide area networks (WANs), include their usually higher data-transfer rates, smaller geographic area, and lack of a need for leased telecommunication lines.
Switched Ethernet is the most common Data Link
Layer implementation on local area networks. At the Network Layer,
the Internet Protocol (i.e. TCP/IP) has become the standard. Smaller
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 11/46
LANs generally consist of one or more switches linked to each other—
often at least one is connected to a router, cable modem, or ADSL
modem for Internet access.
Larger LANs are characterized by their use of redundant links with
switches using the spanning tree protocol to prevent loops, their ability
to manage differing traffic types via quality of service (QoS), and to
segregate traffic with VLANs. Larger LANs also contain a wide variety
of network devices such as switches, firewalls, routers, load balancers,
and sensors.[9]
LANs may have connections with other LANs via leased lines, leased
services, or by tunneling across the Internet using virtual private
network technologies. Depending on how the connections are
established and secured in a LAN, and the distance involved, a LAN
may also be classified as METROPOLITAN AREA NETWORK (MAN)
In a simple network consisting of a few computers, it is easy tovisualize how all of the various components connect. As networksgrow, it is more difficult to keep track of the location of eachcomponent, and how each is connected to the network. Wirednetworks require lots of cabling and network devices to provideconnectivity for all network hosts.
When networks are installed, a physical topology map is createdto record where each host is located and how it is connected tothe network. The physical topology map also shows where thewiring is installed and the locations of the networking devices thatconnect the hosts. Icons are used to represent the actual physicaldevices within the topology map. It is very important to maintainand update physical topology maps to aid future installation andtroubleshooting efforts.
In addition to the physical topology map, it is sometimesnecessary to also have a logical view of the network topology. Alogical topology map groups hosts by how they use the network,no matter where they are physically located. Host names,addresses, group information and applications can be recorded onthe logical topology map.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 12/46
PHYSICAL TOPOLOGY
EQUIPMENTSList of all equipments required for setting up the internal networkof the building for HCL CDC.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 13/46
EQUIPMENT QTY DESCRIPTION
CISCO 2960 Layer 2Switch
9 24 Fast-Ethernet ports, 2Gigabit Ethernet ports
CISCO 2960 GigabitEthernet Switch
5 10 Gigabit Ethernet ports
Linksys WirelessIntegrated Router
3 4 Ethernet ports, 1 Internetport
CISCO 2800 IntegratedService Router
3 7 Gigabit Ethernet, 2 Serialports /6 Gigabit Ethernet, 3 Serial
ports
HP Blade Servers 3 1 Fast-Ethernet port
HP Storage Servers 2 For camera monitoring
IBM Desktop Computers 142 1 Fast-Ethernet port
IBM Laptop Computers 32 1 Fast-Ethernet port,
Integrated Wi-Fi
HP IP Printers 5 1 Fast-Ethernet port/ Wireless
Shielded Twisted PairCable (CAT-5)
2500’
Unshielded Twisted PairCable (CAT-5)
4700’
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 14/46
DESCRIPTION OF DEVICESLAYER-3 DEVICES
• Linksys Wireless Integrated Router
An ISR combines features such as routing and switchingfunctions, security, voice, LAN and WAN connectivity intoa single device. It is designed for small offices and home-based users. It consists of one WAN connection (RouterPort) and four 10/100 Mbps switch ports. It providesservices at broadband speeds.
• CISCO 2800 Integrated Service Router
An ISR combines features such as routing and switchingfunctions, security, voice, LAN and WAN connectivity into
a single device. It is designed for enterprise branchoffices. It supports seven to eight 10/100/1000 MbpsGigabit Ethernet ports and two to three Serial ports. Itprovides services at broadband speeds using T1/E1connectioins.
LAYER-2 DEVICES
• CISCO 2960 Gigabit Ethernet Switch
A switch is a device that is able to direct a stream of messages coming in one port, out of another port basedon the destination MAC address within the frame. Itsupports ten Gigabit Ethernet ports. It is generally usedfor trunk lines which carry a huge amount of traffic.
• CISCO 2960 Layer 2 Switch
This type of switches does not use modules or flash cardslots. Due to this reason, their physical configuration
cannot be changed. It supports twentyfour 10/100 MbpsFast-Ethernet ports and two 10/100/1000 Mbps GigabitEthernet ports.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 15/46
LAYER-1 (PHYSICAL) DEVICES
• Shielded Twisted Pair Cable
They are used for high-speed data transmission. Theindividual pair of wires are wrapped in a shield and theentire four pairs are wrapped in another shield. Itsupports data transmission at rates as high as 1000 Mbps.It is generally used for trunk lines.
• Unshielded Twisted Pair Cable
UTP cable is inexpensive, offers a high bandwidth, and iseasy to install. This type of cable is used to connectworkstations, hosts and network devices. It can come
with many different numbers of pairs inside the jacket,but the most common number of pairs is four. Each pair isidentified by a specific color code. It supports datatransmission speeds of 100 Mbps.
END-USER DEVICES
• HP Blade Servers
These servers are high performance computers used in
businesses and other organizations. They provide themaximum concentration of computing power and stability.It also contains hot-swappable hard-drives.
• HP Storage Servers
These servers are used to store redundant parts of files inorder to prevent them from failing. Servers are usuallykept in secure areas where access is controlled.
• IBM Desktop Computers
These are general purpose computers which provide thebasic desktop services to users. It contains of a Fast-Ethernet port.
• IBM Laptop Computers
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 16/46
These are mobile computers which supports both LAN andWAN connectivity.
• HP IP Printers
These are IP based printers which acts as a host on thenetwork. It contains either a Fast-Ethernet port or aWireless card.
LOGICAL TOPOLOGY
PROTOTYPE OF NETWORK TOPOLOGYThe network topology of the HCL CDC building can be
broadly categorized into three network layers: Access,
Distribution and Core Layer.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 17/46
IP ADDRESSING
Every machine on the internet has a unique identifying number, calledan IPAddress. A typical; IP address looks like this:216.27.61.45
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 18/46
IP ADDRESS is a 32-bit number, usually written in dotted decimalform, that uniquely identifies an interface of some computer. This 32-bit number is divided into 4 octets each separated by a decimal. Outso many values certain values are restricted for use as typical IP
address. For example, the IP address 0.0.0.0 is reserved for thedefault network and the address 255.255.255.255is used forbroadcast.
Each IP address is split into 2 sections:
1) Network address
2) Host address
Individual IP address in same network all have a different value in thehost part of address, but they have identical value in network part,
just as in town there are different street address but same ZIP code.
There are five IP classes:
Class A – This class is for very large networks, such as a majorinternational company. IP addresses with a first octet from 1 to 126are part of this class. The other three octets are each used to identifyeach host.
Net Host or Node
54. 24.54.43
Loopback- The IP address 127.0.0.1 is used as the loopback address.This means that it is used by the host computer to send a messageback to itself. It is commonly used for troubleshooting and networktesting.
Class B- Class B is used for medium-sized networks. A good example
is a large college campus. IP addresses with a first octet from 128to191 are part of this class. Class B addresses also include the secondoctet as part of the Net identifier. The other two octets are used toidentify each host.
Net Host or Node
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 19/46
145.24 53.198
Class C- Class C addresses are commonly used for small to mid-sizebusiness. IP addresses with a first octet from192 to 223 are part of
this class. Class C addresses also include the second and third octetsas part of Net identifier. The last octet is used to identify each host.
Net Host or Node
196.54.34 86
Class D- It is used for multicast. It has first bit value of 1, second bitvalue of 1, third bit value of 1 and fourth bit value of 0. The other 28bits are used to identify the group of computers the multicast
messages is intended for.Net Host or Node
22424.54.145
Class E- It is used for experimental purpose only.
Net Host or Node
240.
23.45.105
Private IP
It is not necessary that every time we make a network we areconnected to some ISP (Internet Service Provider). So in that case werequire some private IP also which can be used in indigenous networks.In each class a range of IP addresses have been defined for thispurpose
CLASS A 10.0.0.1 to 10.255.255.244
CLASS B 172.16.0.1 to 172.34.255.254
CLASS C 192.168.0.0/16
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 20/46
MASKING
Computers use a mask to define size of network and host part of anaddress. Mask is a 32-bit number written in dotted decimal form. Itprovides us the network address when we perform a Boolean AND of
mask with the IP address. It also define number of host bits in anaddress.
Classof address
Size of networkPart of address,in bits
Size of HostPart of address,in bits
Default Maskfor Each Classof Network
A
8 24 255.0.0.0
B16 16 255.255.0.0
C 24 8 255.255.255.0
SUBNETTING
Basically it is a process of subdividing networks into smaller subnets.In case we have 2-3 small networks but we cant buy IP address for
each and every network. So here we use the basic concept of SUBNETTING i.e using one public IP address we will give them IPaddress and make them independent networks. For this we take somebits of host address and use them for network address so we havedifferent independent networks
Address Format when Subnetting Is Used (class A,B,C resp.):
8 24-x x
Network Subnet Host
16 16-xx
Network Subnet Host
24 8-xx
Network SubnetHost
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 21/46
And due to this mask changes to subnet mask and now the networkaddress also includes subnet address.
Example
If subnet mask is 255.255.240.0And an IP address for a computer is given as 142.16.52.4142.16.0.0 is network address0.0.48.0 is the subnet address0.0.4.4 is the host address of the computer
10001110.00010000.00110100.00000100 is ANDed with11111111.11111111.11110000.00000000and output is 10001110.00010000.00110000.00000000
here first two octets represents Network address and third octetrepresents subnet address.It can be compared with a postal address as there is only one ZIP code(Network address), different streets (Subnet address), and differenthouse number (Host address).
Why Bother with VLSM Design?
Suppose, you have just been hired by a new company and need to add
on to the existing network. There is no problem with starting over witha new IP address scheme. Should you use a VLSM classless network ora classful network?
Let’s just say you happen to have plenty of address space because youare using the Class A 10.0.0.0 private network address in yourcorporate environment and can’t even come close to imagining thatyou’d ever run out of IP addresses. Why would you want to botherwith the VLSM design process?
INTRODUCTION TO ROUTER
It is an intelligent device. It works on networks layer. It is used forinternet work communication, packet switching, packet filtering andpath selection. It has no of broadcast and collision domain. By default
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 22/46
router does not broadcast. Router understands different topology andprotocols. It works on full duplex mode.
ROUTER represents a separate network.
The Network layer (also called layer 3) manages device addressing,tracks the location of devices on the network, and determines the bestway to move data, which means that the Network layer must transporttraffic between devices that aren’t locally attached. Routers (layer 3devices) are specified at the Network layer and provide the routingservices within an internetwork. It happens like this: First, when apacket is received on a router interface, the destination IP address ischecked. If the packet isn’t destined for that particular router, it will
look up the destination network address in the routing table. Once therouter chooses an exit interface, the packet will be sent to thatinterface to be framed and sent out on the local network. If the routercan’t find an entry for the packet’s destination network in the routingtable, the router drops the packet. Two types of packets are used atthe Network layer: data and route updates.
Data packets Used to transport user data through the internetwork.Protocols used to support data traffic are called routed protocols;examples of routed protocols are IP and IPv6.
Route update packets Used to update neighboring routers about thenetworks connected to all routers within the internetwork. Protocolsthat send route update packets are called routing protocols; examplesof some common ones are RIP, RIPv2, EIGRP, and OSPF. Route updatepackets are used to help build and maintain routing tables on eachrouter.
Network addresses Protocol-specific network addresses. A routermust maintain a routing table for individual routing protocols becauseeach routing protocol keeps track of a network with a differentaddressing scheme (IP, IPv6, and IPX, for example).
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 23/46
3.2
Interface The exit interface a packet will take when destined for aspecific network.
Metric It is the distance to the remote network. Different routingprotocols use different ways of computing this distance
Routers break up broadcast domains, which mean that by default,broadcasts aren’t forwarded. Routers also break up collision domains,but you can also do that using layer 2 (Data Link layer) switches.Because each interface in a router represents a separate network, itmust be assigned unique network identification numbers, and eachhost on the network connected to that router must use the same
network number.
A router in an internetwork
o Each router interface is a broadcast domain. Routers break up
broadcast domains by default and provide WAN services.
o Routers, by default, will not forward any broadcast or multicast
packets.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 24/46
1o Routers use the logical address in a Network layer header to
determine the next hop router to forward the packet to.1
o Routers can use access lists, created by an administrator, to control
security on the types of packets that are allowed to enter or exit aninterface.2
o Routers can provide layer 2 bridging functions if needed and can
simultaneously route through the same interface.
o Routers provide connections between virtual LANs (VLANs).
Because by creating contiguous blocks of addresses to specific areas of your network, you can then easily summarize your network and keeproute updates with a routing protocol to a minimum. Why wouldanyone want to advertise hundreds of networks between buildingswhen you can just send one summary route between buildings andachieve the same result? Summarization, also called Supernetting,provides route updates in the most efficient way possible by
advertising many routes in one advertisement instead of individually.
Some terminologies those are used with Networking models:
Collision Domain- It is the group of PC’s in which collision will occurwhen two PC will transmit data simultaneously.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 25/46
Broadcast Domain- It is the group of PC’s those will receive samebroadcast message.
CSMA/CD (Carrier Sense Multiple Access/ Collision Detection)-In this protocol when a PC wants to transmit any packet it sense thecarrier i.e the path ,if no other PC is using the carrier then only itsends. If two PCs starts sending data simultaneously collision willoccur. Both PCs will wait for some random time and then initiate thesame process.
MAC (Media Access Control) . The IEEE 802.3 (Ethernet) and 802.5(Token Ring) are the MAC sub layers of these two LAN data-linkprotocols.
Burned-in address: The 6-byte address assigned by the vendormakingthe card. It is usually burned in to a ROM or EEPROM on the LAN cardand begins with a 3-byte organizationally unique identifier (OUI)assigned bythe IEEE.
Locally administered address: Through configuration, an addressthat is used instead of the burned-in address.
Unicast address: Fancy term for a MAC that represents a single LANinterface.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 26/46
VLANS (Virtual LANs)
A VLAN permits a group of users to share a common broadcast domainregardless of their physical location in the internetwork. VLAN improveperformance and security in switched networks.
A Catalyst switch operates in a network like a traditional bridge. EachVLAN configured on the switch implements address learning,forwarding/filtering decisions, and loop avoidance mechanisms.
Ports belonging to a VLAN are configured with a membership modethat determines to which VLAN they belong. Catalyst switches supporttwo VLAN membership modes: static and dynamic.
The IEEE 802.1Q protocol is used to transport frames for multipleVLANs between switches and routers, and for defining VLANtopologies.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 27/46
WAN (Wide Area Network) and Protocols involved
Below figures shows the different WAN connection types that can beused to connect distant devices.
WAN connection types
Synchronous serial
Here’s a list explaining the different WAN connection types:
Leased lines These are usually referred to as a point-to-point ordedicated connection. A leased line is a pre-established WAN
communications path that goes from the CPE through the DCE switch,then over to the CPE of the remote site. The CPE enables DTEnetworks to communicate at any time with no cumbersome setupprocedures to muddle through before transmitting data.
When you’ve got plenty of cash, this is really the way to go because ituses synchronous serial lines up to 45Mbps. HDLC and PPP
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 28/46
encapsulations are frequently used on leased lines.
Circuit switching When you hear the term circuit switching, thinkphone call. The big advantage is cost—you only pay for the time youactually use. No data can transfer before an end-to-end connection isestablished. Circuit switching uses dial-up modems or ISDN and isused for low-bandwidth data transfers.
Packet switching This is a WAN switching method that allows you toshare bandwidth with other companies to save money. Packetswitching can be thought of as a network that’s designed to look like aleased line yet charges you more like circuit switching. But less costisn’t always better—there’s definitely a downside: If you need totransfer data constantly, just forget about this option. Instead, get
yourself a leased line. Packet switching will only work for you if yourdata transfers are the bursty type—not continuous. Frame Relay andX.25 are packet-switching technologies with speeds that can rangefrom 56Kbps up to T3 (45Mbps).
Frame Relay A packet-switched technology that made its debut in theearly 1990s, Frame Relay is a high-performance Data Link andPhysical layer specification. It’s pretty much a successor to X.25,except that much of the technology in X.25 used to compensate forphysical errors (noisy lines) has been eliminated. An upside to Frame
Relay is that it can be more cost effective than point-to-point links,plus it typically runs at speeds of 64Kbps up to 45Mbps (T3). AnotherFrame Relay benefit is that it provides features for dynamic bandwidthallocation and congestion control.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 29/46
HDLC High-Level Data-Link Control (HDLC) was derived fromSynchronous Data Link Control (SDLC), which was created by IBM as aData Link connection protocol. HDLC works at the Data Link layer andcreates very little overhead compared to LAPB. It wasn’t intended toencapsulate multiple Network layer protocols across the same link—the HDLC header doesn’t contain any identification about the type of protocol being carried inside the HDLC encapsulation. Because of this,each vendor that uses HDLC has its own way of identifying theNetwork layer protocol, meaning each vendor’s HDLC is proprietarywith regard to its specific equipment.
PPP Point-to-Point Protocol (PPP) is a pretty famous, industry-standard protocol. Because all multiprotocol versions of HDLC areproprietary, PPP can be used to create point-to-point links betweendifferent vendors’ equipment. It uses a Network Control Protocol fieldin the Data Link header to identify the Network layer protocol andallows authentication and multi-link connections to be run overasynchronous and synchronous links.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 30/46
Project Work
ADDRESSING INFORMATION OF LAYER-3 DEVICESROUTERS
DEVICE INTERFACE
IP ADDRESS SUBNET MASK
Core Router Serial 7/0 212.212.212.2
255.255.255.0
Serial 8/0 192.168.10.6
255.255.255.252
Serial 9/0 192.168.10.2
255.255.255.252
Gb E0/0.27
192.168.8.2 255.255.255.240
Gb E0/0.28
200.200.200.1
255.255.255.248
Lab A Router Serial 8/0 192.168.10.1
255.255.255.252
Gb E0/0.15
192.168.2.225
255.255.255.224
Gb E0/0.16
192.168.2.177
255.255.255.240
Gb E0/0.17
192.168.2.161
255.255.255.240
Gb E0/0.18
192.168.2.193
255.255.255.240
Gb E
0/0.19
192.168.2.2
09
255.255.255.2
40Gb E
0/0.24192.168.2.2 255.255.255.2
24
Gb E0/0.25
192.168.2.33
255.255.255.224
Gb E 192.168.2.6 255.255.255.2
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 31/46
0/0.26 5 40
Lab B Router Serial 8/0 192.168.10.5
255.255.255.252
Gb E 0/0.9 192.168.2.65
255.255.255.224
Gb E0/0.10
192.168.2.2 255.255.255.224
Gb E0/0.11
192.168.2.33
255.255.255.224
Gb E0/0.12
192.168.2.97
255.255.255.224
Gb E
0/0.13
192.168.2.1
29
255.255.255.2
24
Finance Deptt.Wireless Router
Internet 192.168.1.4 255.255.255.224
LAN 192.168.3.2 255.255.255.0
Seminar Hall-1Wireless Router
Internet 192.168.1.3 255.255.255.224
LAN 192.168.3.1 255.255.255.0
Seminar Hall-2Wireless Router
Internet 192.168.2.4 255.255.255.224
LAN 192.168.4.1 255.255.255.0
ADDRESSING INFORMATION OF LAYER-2 DEVICESSWITCHES
DEVICE INTERFACE
MODE VLAN ID
Server Switch 0/1 Access 28
1/1 Access 28
2/1 Trunk 1-1005
3/1 Access 27
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 32/46
Lab-A Core Switch 0/1 Trunk 1-14,16,20-1005
1/1 Trunk 1-15,17,20-1005
2/1 Trunk 1-14,18-10053/1 Trunk 1-1005
Lab-B Core Switch 0/1 Trunk 1-1005
2/1 Trunk 1-14,20-1005
Floor 1 Switch 0/1 Access 24
1/1 Trunk 1-23,26-1005
2/1 Trunk 1-23,25,27-
10053/1 Access 24
4/1 Trunk 1-1005
COMPLETE LOGICAL NETWORK TOPOLOGY
• IP ADDRESSING
A host needs an IP address to participate on the Internet. The
IP address is a logical network address that identifies aparticular host. It must be properly configured and unique inorder to communicate with other devices on the Internet.An IP address is assigned to the Network interface connectionfor a host. This connection is usually a network interface card(NIC) installed in the device. Examples of end-user deviceswith network interfaces include workstations, servers, networkprinters and IP phones. Some servers can have more than oneNIC and each of these has its own IP address. Router
interfaces that provide connections to an IP network will alsohave an IP address.Every packet sent across the Internet has a source anddestination IP address. This information is required bynetworking devices to insure the information gets to thedestination and any replies are returned to the source.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 33/46
• IP ADDRESSING STRUCTURE
An IP address is simply a series of 32 binary bits (ones andzeros). It is very difficult for humans to read a binary IPaddress. For this reason, the 32 bits are grouped into four 8-bitbytes called octets. An IP address in this format is hard forhumans to read, write and remember. To make the IP addresseasier to understand, each octet is presented as its decimalvalue, separated by a decimal point or period. This is referredto as dotted-decimal notation.The 32-bit IP address is defined with IP version 4 (IPv4) and is
currently the most common form of IP address on the Internet.There are over 4 billion possible IP addresses using a 32-bitaddressing scheme.When a host receives an IP address, it looks at all 32 bits asthey are received by the NIC. Humans, on the other hand,need to convert those 32 bits into their four octet decimalequivalent. Each octet is made up of 8 bits and each bit has avalue. The four groups of 8 bits have the same set of values.The rightmost bit in an octet has a value of 1 and the values of
the remaining bits, from right to left, are 2, 4, 8, 16, 32, 64and 128.
• IP ADDRESS CLASSES
The IP address and subnet mask work together to determinewhich portion of the IP address represents the network addressand which portion represents the host address. The class of anaddress can be determined by the value of the first octet.IP addresses are grouped into 5 classes. Classes A, B and C arecommercial addresses and are assigned to hosts. Class D isreserved for multicast use and Class E is for experimental use.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 34/46
• Class C addresses have three octets for the network portion
and one for the hosts. The default subnet mask is 24 bits
(255.255.255.0). Class C addresses are usually assigned to
small networks.
• Class B addresses have two octets to represent the network
portion and two for the hosts. The default subnet mask is 16
bits (255.255.0.0). These addresses are typically used for
medium-sized networks.
• Class A addresses have only one octet to represent the
network portion and three to represent the hosts. The
default subnet mask is 8 bits (255.0.0.0). These addresses
are typically assigned to large organizations.
In the addressing scheme of HCL CDC, we have used Class-Caddressing scheme. In the Class-C addressing scheme, thereare a total of 256 addresses available. Out of these, 254addresses are usable. The remaining to addresses are reservedfor network and broadcast address.IP addresses are of two types: Private addresses and Publicaddresses. All hosts that connect directly to the Internetrequire a unique public IP address. Because of the finitenumber of 32-bit addresses available, there is a risk of runningout of IP addresses. This problem can be resolved by the useof Private addresses. They allow hosts within an organizationto communicate with one another without the need of a uniquepublic IP address. Table below shows a list of Privateaddresses:
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 35/46
SUBNETTINGThe customer network using the single ISR is badlyoverloaded. The proposed solution is to add a secondnetworking device, a larger ISR, and to divide the singlenetwork into two separate networks.For security purposes, the wireless and wired users need to beon separate local networks.In the subnetting scheme for HCL CDC, we utilize the conceptof classless subnetting where we use custom subnets todifferentiate the networks.Routers distinguish between networks by using the subnetmask to determine which bits make up the network ID andwhich bits make up the host portion of the address. When anetwork is partitioned, the router needs a modified or customsubnet mask to distinguish the subnets from each other. Adefault subnet mask and a custom subnet mask differ fromeach other as follows: Default subnet masks only change onoctet boundaries. For instance, the default subnet mask for aClass A network is 255.0.0.0. Custom subnet masks take bitsfrom the host ID portion of the IP address and add them to thedefault subnet mask.
SWITCHING
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 36/46
A switch is a device that is able to direct a stream of messagescoming in one port, out of another port based on thedestination MAC address within the frame. A switch cannotroute traffic between two different local networks. In the
context of the OSI model, a switch performs the Layer 2,known as the data-link layer function.Only one message can be sent through an Ethernet hub at atime. It is possible for two or more hosts connected to a hub toattempt to send a message at the same time. If this happens,the electronic signals that make up the messages collide witheach other at the hub.A collision causes the messages to become garbled andunreadable by the hosts. A hub does not decode the
messages; therefore it does not detect that the message isgarbled and repeats it out all the ports. The area of thenetwork where a host can receive a garbled message resultingfrom a collision is known as a collision domain.A switch is preferred over hubs in the networking model of HCLCDC because of the large collision domain associated withhubs. Since a switch uses micro-segmentation, it narrowsdown the collision domain. The network of HCL CDC uses 9CISCO switches, which can result in a huge broadcast domain.
So, to minimize the domain, we have used the concept of Virtual LAN (VLAN).
VIRTUAL LAN
A VLAN is a logical broadcast domain that can span multiplephysical LAN segments. It allows an administrator to grouptogether stations by logical function, by project teams, or by
applications, without regard to physical location of the users.A VLAN has two major functions:
• A VLAN contains broadcasts.
• A VLAN groups devices. Devices located on one VLAN are
not visible to devices located on another VLAN.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 37/46
Configuring a VLAN:
In order to configure VLAN on a switch, connect it with aterminal device using a console cable.Enter the privileged mode using the enable commandSwitch>enableSwitch#Enter the configuration mode using the configure terminalcommandSwitch# configure terminalSwitch (config) #
Enter the name and VLAN number using the commandsSwitch(config)#vlan vlan_numberSwitch(config-vlan)#name vlan_nameSwitch(config-vlan)#exitUse the following commands to assign individual ports toVLANs:
Switch(config)#interface fa#/#Switch(config-if)#switchport access vlan vlan_number
Switch(config-if)# exit
Use the following commands to assign a range ports toVLANs:
Switch(config)#interface range fa#/start_of_range -end_of_range
Switch(config-if)#switchport access vlan vlan_numberSwitch(config-if)#exitTo disassociate a port from a specific VLAN:Switch(config)#interface fa#/#Switch(config-if)#no switchport access vlan vlan_numberA switch port can function in two modes: Access and Trunkmode.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 38/46
To switch between the two modes, use the followingcommandSwitch(config)#interface fa#/#
Switch(config-if)#switchport mode <trunk/access>
A switchport in the trunk mode is used for a switch-switch orswitch-router connection, whereas an access mode is used forconnection to terminal devices.
SWITCH CONFIGURATIONCore Switches
SWITCH INTERFACE MODE VLAN ID
Server Switch Gb E 0/1,1/1 Access 28
Gb E 2/1 Trunk 1-1005
Gb E 3/1 Access 27
Floor-1 Switch Gb E 0/1,3/1 Trunk 24
1/1 Trunk 1-23,26-1005
2/1 Trunk 1-23,25,27-1005
4/1 Trunk 1-1005
Lab A CoreSwitch
0/1 Trunk 1-14,16,20-1005
1/1 Trunk 1-15,17,20-1005
2/1 Trunk 1-14,18-1005
3/1 Trunk 1-1005
Lab B CoreSwitch
0/1 1-1005
2/1 1-14,20-1005
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 39/46
Other Switches
SWITCH INTERFACE MODE VLAN ID
Main Deptt.
Switch
Fa E 0/1-0/6 Access 18
Fa E 0/7-0/11 Access 19
Gb E 1/1 Trunk 1-1005
IT Deptt.Switch
Fa E 0/1-0/8 Access 15
Fa E 0/10-0/13
Access 17
Gb E 1/1 Trunk 1-1005
Java classroomSwitch
Fa E 0/1-2/1,4/1
Access 16
3/1 Trunk 1-1005
CCNA classroomSwitch
Fa E <all> Access 13
Gb E 1/1 Trunk 1-1005
DB Switch Fa E <all> Access 12
Gb E 1/1 Trunk 1-1005
OP Switch Fa E <all> Access 9
Gb E 1/1 Trunk 1-1005
PC Switch Fa E <all> Access 11
Gb E 1/1 Trunk 1-1005
Lab B MainSwitch
Gb E 0/1 Trunk 1-8,11,14-1005
Gb E 1/1 Trunk 1-9,14-1005
Gb E 2/1 Trunk 1-8,12,14-
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 40/46
1005
Gb E 3/1 Trunk 1-8,13-1005
Gb E 4/1 Access 10
Gb E 5/1 Trunk 1-1005
D Switch Fa E <all> Access 26
Gb E 1/1 Trunk 1-1005
HD Switch Fa E <all> Access 25
Gb E 1/1 Trunk 1-1005
ROUTING
Routing is the process of finding a path to the destination host.A router is a networking device that connects a local networkto other local networks. At the Distribution Layer of thenetwork, routers direct traffic and perform other functionscritical to efficient network operation. Routers, like switches,are able to decode and read the messages that are sent tothem. Unlike switches, which only decode (unencapsulate) theframe containing the MAC address information, routers decodethe packet that is encapsulated within the frame.
Each port, or interface, on a router connects to a different localnetwork. Every router contains a table of all locally-connectednetworks and the interfaces that connect to them. Theserouting tables can also contain information about the routes, orpaths, that the router uses to reach other remote networksthat are not locally attached.When a router receives a frame, it decodes the frame to get tothe packet containing the destination IP address. It matchesthe address of the destination to all of the networks that are
contained in the routing table. If the destination networkaddress is in the table, the router encapsulates the packet in anew frame in order to send it out. It forwards the new frameout of the interface associated with the path, to the destinationnetwork. The process of forwarding the packets toward theirdestination network is called routing.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 41/46
Router interfaces do not forward messages that are addressedto the broadcast MAC address. As a result, local networkbroadcasts are not sent across routers to other local networks.
Configuring a ROUTER:
In order to configure a router, the following commands canbe executed.Enter the privileged mode using the enable commandRouter>enableRouter#
Enter the configuration mode using the configure terminalcommandRouter# configure terminal
Router (config) #
The host from the sending VLAN forwards traffic to the routerusing the default gateway. The sub-interface for the VLANspecifies the default gateway for all hosts in that VLAN. Therouter locates the destination IP address and does a routingtable lookup.If the destination VLAN is on the same switch as the sourceVLAN, the router forwards the traffic back down to the source
switch using the subinterface parameters of the destinationVLAN ID. This type of configuration is often referred to as arouter-on-a-stick.If the exit interface of the router is 802.1Q-compatible, theframe retains its 4-byte VLAN tag. If the outbound interface isnot 802.1Q-compatible, the router strips the tag from theframe and returns the frame to its original Ethernet format.To configure inter-VLAN routing, use the following steps:1. Configure a trunk port on the switch.
Switch(config)#interface fa0/2Switch(config-if)#switchport mode trunk
2. On the router, configure a FastEthernet interface with no IPaddress or subnet mask.
Router(config)#interface fa0/1Router(config-if)#no ip address
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 42/46
Router(config-if)#no shutdown
3. On the router, configure one subinterface with an IP addressand subnet mask for each VLAN. Each subinterface has an
802.1Q encapsulation.Router(config)#interface fa0/0.10Router(config-subif)#encapsulation dot1q 10Router(config-subif)#ip address 192.168.10.1
255.255.255.0
4. Use the following commands to verify the inter-VLAN routingconfiguration and functionality.
Switch#show trunk
Router#show ip interfacesRouter#show ip interfaces brief Router#show ip route
ADDRESSING SCHEME
ROOM IP ADDRESSRANGE
SUBNET MASK DEFAULTGATEWAY
Manager’s
Office
192.168.2.210
-222
255.255.255.24
0
192.168.2.20
9
HumanResourcesDept
192.168.2.210-222
255.255.255.240
192.168.2.209
Accounts Dept 192.168.2.194-206
255.255.255.240
192.168.2.193
Application
Development
192.168.2.226
-254
255.255.255.22
4
192.168.2.22
5
MarketingRoom
192.168.2.162-174
255.255.255.240
192.168.2.161
Special 192.168.2.178 255.255.255.24 192.168.2.17
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 43/46
Projects Room -190 0 7
Testing & Simulation
Room
192.168.2.130-158
255.255.255.224
192.168.2.129
DebuggingRoom
192.168.2.98-126
255.255.255.224
192.168.2.97
OptimizationRoom
192.168.2.66-94
255.255.255.224
192.168.2.65
Prototype
Construction
192.168.2.34-
62
255.255.255.22
4
192.168.2.33
ConferenceHall
192.168.4.2-62
255.255.255.192
192.168.4.1
Waiting Room 192.168.3.2-62
255.255.255.192
192.168.3.1
HelpDesk/Custome
r Care
192.168.1.34-62
255.255.255.240
192.168.1.33
Documentation Room
192.168.1.66-79
255.255.255.240
192.168.1.65
Cafeteria 192.168.3.0-254
255.255.255.0 192.168.3.1
INTERNET CONNECTIONThe Internet is a network of networks that connects users inevery country in the world. There are currently over one billionInternet users worldwide.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 44/46
Any home, business or organization that wants to connect to theInternet must use an Internet Service Provider (ISP). An ISP is acompany that provides the connections and support to access theInternet. It can also provide additional services such as Email and
web hosting.ISPs are essential to gaining access to the Internet. No one getson the Internet without a host computer, and no one gets on theInternet without going through an ISP. ISPs range in size fromsmall to very large and differ in terms of the area they service.ISPs also differ in the types of connection technologies andspeeds they offer.
ISP LEVELS OF SERVICEWhen data is transferred, it is either uploaded or downloaded.Downloading refers to information coming from the Internet toyour computer, while uploading indicates the reverse path, fromyour computer to the Internet. When the download transfer rateis different from the upload transfer rate, it is called asymmetric.When the transfer rate is the same in both directions, it is calledsymmetric. ISPs can offer both asymmetric and symmetricservices.
The HCL CDC is to use T1 symmetric connection from any ISP.The advantage of using a symmetric T1 connection is that it cancarry large amounts of data in both directions at equal rates.Moreover, it helps when we need to upload large amounts of traffic such as intensive graphics, multimedia, or video.The network for HCL CDC was established with an eye towardsthe prospects for future upgrades.
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 45/46
Result and Conclusion
The HCL CDC network built up is installed in theComputer Lab, and is based on the same networkingmodel created and discussed here in the project report.
The N/W model is suited for a small business andwork. It is formed by following best practices ascommenced by the CISCO N/W academy.
The model is laid down by the prospect of futureupgrades as required by the enterprise. It adjusts andaccommodates major upgrades without changing theactual model.
Any additional constraints can be added and the N/W
be redesigned with those constraints functional.
The N/W created gives functioning environment tothe next shown Physical Layout
8/3/2019 Synopsis Network
http://slidepdf.com/reader/full/synopsis-network 46/46
BIBLIOGRAPHY
Books:-
Stevens W Richard., “TCP/IP Illustrated Volume - I”Pearson Education, Second Edition.Strebe Mathew, Tata McGraw Hill, Seventh EditionCCNA: Cisco Certified Networking Associate, Study Guide, Todd
Lemmle
Sites:-
www.about.com
http://en.wikipedia.org/wiki/