Download - SOP Cessna 150-152
-
8/9/2019 SOP Cessna 150-152
1/142
SOP C150/C152 - Issue 08 Page 1 - 142
Standard OperatingProcedures
(SOP’s)
Cessna 150
PH-RUD / PH-NOD / PH-HVP / PH-TGACessna 152
PH-JVB / PH-CDS / PH-STQ /PH-WEE / PH-SCX / PHSKG
Name:
COPYRIGHT Stella aviation academyNo part of this manual or its extracts may be reproduced in any form, by print, photo print,
microfilm or any other means, without written permission from Stella aviation academy.
-
8/9/2019 SOP Cessna 150-152
2/142
Standard Operating Procedures
Cessna 150/C152
Page 2 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
3/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 3 - 142
ISSUE RECORD
Issue Number Issue Date
01 09-12-2005
02 01-10-2006
03 01-01-2008
04 19-10-2011
05 07-11-2011
06 01-05-2012
07 01-10-2012
08 06-02-2013
-
8/9/2019 SOP Cessna 150-152
4/142
Standard Operating Procedures
Cessna 150/C152
Page 4 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
5/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 5 - 142
TABLE OF CONTENTS
CHAPTER 1 .................................................................................................................................................... 7
1.0 INTRODUCTION .......................................................... ................................................................. ..................... 7
1.1 SOURCES .............................................................................................................. ........................................... 7
1.2 STANDARD OPERATING PROCEDURES .................................................................................. ..................... 7
1.3 AIRMANSHIP ............................................................... ................................................................. ..................... 7
1.4 CHECKLIST ISSUES .............................................................. ................................................................. .......... 7
CHAPTER 2 .................................................................................................................................................... 9
2.0
ABBREVIATIONS USED IN THIS BOOK: ......................................................................................................... 9
CHAPTER 3 .................................................................................................................................................. 11
3.0 SPEEDS FOR DIFFERENT FLIGHT PHASES ....................................................... ......................................... 11
CHAPTER 4 .................................................................................................................................................. 13
4.0 DIFFERENCES WITH STANDARD PROCEDURE ................................................ ......................................... 13
CHAPTER 5 .................................................................................................................................................. 17
5.0 NORMAL CHECKLIST C150/C152 .............................................................. .................................................... 17
5.1 CESSNA 150; PH-RUD/NOD/HVP ....................................................................................................... ........... 17
5.2
EXPANDED NORMAL CHECKLIST C150: PH-RUD/NOD/HVP ....................................... .............................. 23
5.3 CESSNA 152: PH-JVB/CDS/STQ/WEE ....................................................... .................................................... 35
5.4 EXPANDED NORMAL CHECKLIST C152: PH-JVB/CDS/STQ/WEE .............................................................. 41
5.5 CESSNA 150: PH-TGA ........................................................... ................................................................. ........ 53
5.6 EXPANDED NORMAL CHECKLIST C150: PH-TGA ......................................................... .............................. 59
5.7 CESSNA 150: PH-SCX ........................................................... ................................................................. ........ 69
5.8 EXPANDED NORMAL CHECKLIST C150: PH-SCX ......................................................... .............................. 75
5.9 CESSNA 152: PH-SKG ........................................................... ................................................................. ........ 87
5.10 EXPANDED NORMAL CHECKLIST C150: PH-SKG ......................................................... .............................. 93
5.11
EMERGENCY CHECKLIST C150 PH-HVP/RUDNOD ...................................................... ............................ 105
5.12 EMERGENCY CHECKLIST C150 PH-JVB/CDS/STQ/WEE ......................................................... ................. 118
5.13 EMERGENCY CHECKLIST C150 PH-TGA ............................................................ ....................................... 123
5.14 EMERGENCY CHECKLIST C150 PH-SCX ............................................................ ....................................... 131
5.15 EMERGENCY CHECKLIST C150 PH-SKG ............................................................ ....................................... 137
-
8/9/2019 SOP Cessna 150-152
6/142
Standard Operating Procedures
Cessna 150/C152
Page 6 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
7/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 7 - 142
CHAPTER 1
1.0 INTRODUCTION
This book contains the Standard Operating Procedures covering the VFR operation of C150/C152. Thebook is a integral part of the way to handle an aircraft during VFR conditions. It’s not possible to cover alleventualities and there for good airmanship and common sense is expected of the crew. The speeds andprocedures in this part must be preferred above the AOM/POH. No marks are made to indicate changes onthe previous issue due to the amount of changes.
1.1 SOURCES
Material used from:
- AOM- POH- SOPs VFR General
- Company Notams
1.2 STANDARD OPERATING PROCEDURES
The SOPs in this chapter have a direct relation to the execution of a safe flight. They shall be knownthoroughly and used throughout the rest of your career as a pilot. Basically these SOPs inform the studentabout the margins within which to operate, and step-by-step how to execute different flight manoeuvres in astandard way.Using SOPs greatly enhances the safety of flight, especially in non-standard circumstances.
1.3 AIRMANSHIP
Definition: All facets that allow the pilot to control the airplane at any time during the flight in accordancewith regulations in a safe way, on the ground as well as in the air.
During the ground school all different facets that compose airmanship will be illustrated. Safety is a veryimportant part in the mind of every conscientious airline pilot. Adherence to rules and regulations is only thefirst part to incorporate "airmanship" into your existence.
1.4 CECKLIST ISSUES
Pay attention to the fact that this SOP document might have another issue number than mentioned on thevalid checklists. For the valid checklist issues refer to the document control list of SAA.
-
8/9/2019 SOP Cessna 150-152
8/142
Standard Operating Procedures
Cessna 150/C152
Page 8 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
9/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 9 - 142
CHAPTER 2
2.0 ABBREVIATIONS USED IN THIS BOOK
AGL Above Ground Level AOM/POH Aircraft Operating Manual/ Pilots Operating Handbook ARO Aerodrome Reporting Office ATC Air Traffic Control ATPL Airline Transport Pilots LicenseCVV Carburettor heatFIR Flight Information RegionICAO International Civil Aviation OrganizationFIO Flight Information OfficeIFR Instrument Flight RulesITM IFR Training ManualME Multi EngineNOTAM Notices to Airman (Part of Aeronautical Information Publication)OM Operating ManualOPS Operations department of Stella aviation academyORP Outside Reference PointPIC Pilot In CommandRT RadiotelephonySE Single EngineSOP Standard Operating ProcedureUTC Universal Time CoordinationVFG VFR-guide (Part of Aeronautical Information Publication in the Netherlands)VFR Visual Flight Rules
Speeds:
Vrotate Rotation speedVcclimb Climb speedVcruise Cruise speedVdecsent Descent speedVglide Glide speedVstall Stall speedVs1 Stall speed, clean configurationVs0 Stall speed, landing configurationVslow Slow speedVhigh High speedVx Maximum angle of climbVy Maximum rate of climb
-
8/9/2019 SOP Cessna 150-152
10/142
Standard Operating Procedures
Cessna 150/C152
Page 10 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
11/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 11 - 142
CHAPTER 3
3.0 SPEEDS FOR DIFFERENT FLIGHT PHASES
For calculation of the speeds from kts. to mph. add the factor 10, for example 80 kts is 90 mph.
TAKE-OFFVrotate normal take-off 50 kts. Other take offs: see POH.
Flight Phase Powersetting
Flaps C150 C152
normal take-off full throttle flaps up 70 kts. 80 mph. 70 kts.
obstacle take-off full throttle flaps up 60 kts. 70 mph. 54 kts.
obstacle take-offPH-TGA
full throttle flaps up 56 kts.
short field take-off full throttle flaps 10° 60 kts. 70 mph. 54 kts.
soft field take-off full throttle flaps 10° 70 kts. 80 mph. 70 kts.
SPEEDS & POWERSETTINGS
Flight Phase Power setting C150 C152
cruise climb full throttle 70 kts. 70 kts.
best angle of climb full throttle 61 kts. 54 kts.
best angle of climbPH-TGA
full throttle 56 kts.
best rate of climb full throttle 68 kts. 67 kts.
Airwork 2300 RPM 85 kts. 85 kts.
cruise flight according POH
slow flight 1800 RPM 50-70 kts. 50-70 kts.high speed 2400 RPM 100 kts. 100 kts.
steep turn 2500 RPM 85 kts. 85 kts.
Descent 1700 RPM 85 kts. 85 kts.
Glide throttle idle 60 kts. 60 kts.
SPEED & FLAPSETTING IN CIRCUIT
Power settings are indications and can be different for each C150/C152! The different in power settingbetween downwind and base leg is approximately about 400 RPM in no wind conditions.
Flight Phase Power setting Flap setting Speed
cross wind leg, climb full throttle up 70 kts.
cross wind leg,circuit altitude
2100 RPM up 80 kts.
downwind 2100 RPM up 80 kts.after downwind checks 2100 RPM flaps 10° 75 kts.
base leg 1700 RPM flaps 20° 70 kts.
final 1700 RPM flaps full 60 kts.
strong crosswind landing 1800 RPM flaps 20° 65 kts.
flapless landing 1600 RPM flaps up 65 kts.
glide-in landing idle flaps full 60 kts.
-
8/9/2019 SOP Cessna 150-152
12/142
Standard Operating Procedures
Cessna 150/C152
Page 12 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
13/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 13 - 142
CHAPTER 4
4.0 DIFFERENCES WITH STANDARD PROCEDURE
No trimming
Vs1 or Vs0 + 10 kts. Keep direction with rudder, aileron neutral
Approach to stall, landing configuration:
Short field take-off:
Short field take-off
flaps 10°
line aircraft up at beginning of runwayand check runway direction
check heading versus desired runway
check wind direction, yoke about halftravel into wind
apply brakes
smoothly apply full throttle
check engine instruments
brakes released
maintain direction with rudder
elevator slightly tail low
after liftoff adjust attitude, accelerate toclimb speed
Approach to stall, landing configuration:
check outside clear, O.R.P.
reduce throttle to +/- 1900 RPM
apply back pressure
ailerons neutral
white arc, full flaps in steps
reduce throttle to +/- 1700 RPM
stall recovery:- simultaneously full throttle, CVV
cold- maintain attitude and heading- flaps 20°
passing 60 kts. flaps 10°
passing 70 kts. flaps up
with Vclimb, back to altitude
-
8/9/2019 SOP Cessna 150-152
14/142
Standard Operating Procedures
Cessna 150/C152
Page 14 - 142 SOP C150/C152 - Issue 08
Soft field take-off:
Soft field take-off flaps 10°
hold control column aft
line aircraft up at beginning of runwayand check runway direction
keep aircraft rolling
check heading versus desired runway
check wind direction, yoke about halftravel into wind
smoothly apply full throttle
maintain direction with rudder
keep control column aft and fly theaircraft off the ground
after liftoff adjust attitude, accelerate tonormal climb speed.
Crosswind landingWith a crosswind component above 10 kts reduce flaps setting to flaps 20°. The final speed mustbe increased with 5 kts, final speed will be 65 kts.
Flapless landingWith a flapless landing increase speed at base to 75 kts and increase the final speed to 65 kts.
Glide-in landing
The glide-in landing must be made with the best glide-in speed of 60 kts.
Touch and goNormally during a touch and go, after the touch flaps will be selected up. However, during a softfield touch and go, the flaps can be selected to 10°
-
8/9/2019 SOP Cessna 150-152
15/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 15 - 142
Go around or wave-off:
Flight Phase or EventSTUDENT
Go around Initiating go around “GO AROUND”
select full throttle
carburettor heat OFF
maintain direction with rudder
attitude for climb
“FLAPS 20°”
select flaps 20º if flaps weremore than 20º
“FLAPS 20° SET”
Wave-off Initiating go around “WAVE OFF”
select full throttle
carburettor heat OFF
maintain direction with rudder
maintain attitude to accelerateto climb speed
“FLAPS 20°”
select flaps 20º if flaps weremore than 20º
“FLAPS 20° SET”
After initiating the Go around or Wave-off continue as follows to resume normal climbout:
Positive airborne,positive rate of climband above 50 ft AGL
check brakes
“BRAKES CHECKED”
attitude for climb, increasespeed to 70 kts
attitude to climb speed
speed more than 60 kts.
“FLAPS 10°”
select flap 10°
“FLAPS 10° SET”
At 200 ft AGL after take-off checks
“FLAPS UP”
select flaps up
“FLAPS ARE UP”
“After take-off checklist”
-
8/9/2019 SOP Cessna 150-152
16/142
Standard Operating Procedures
Cessna 150/C152
Page 16 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
17/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 17 - 142
CHAPTER 5
5.0 NORMAL CHECKLIST C150/C152
5.1 CESSNA 150 PH-RUD/NOD/HVP
PREFLIGHT INSPECTION
Note:Visually check airplane for general condition during walk-around inspection. In cold weather, remove evensmall accumulations of frost, ice or snow from wing, tail and control surfaces.
Also, make sure that control surfaces contain no internal accumulations of ice or debris. Prior to flight,check that pitot heater (if installed) is warm to touch within 30 seconds with battery and pitot heat switcheson. If a night flight is planned, check operation of all lights, and make sure a flashlight is available.
CABIN
Pilot’s Operating Handbook ............. AVAILABLE IN AIRPLANEControl Wheel Lock .................................................... REMOVEIgnition Switch ..................................................................... OFFMaster Switch ..................................................... .................. ON
WarningWhen turning on the master switch, using an externalpower source, or pulling the propeller through by hand,
treat the propeller as if the ignition switch were on. Do notstand, nor allow anyone else to stand, within the arc of thepropeller, since a loose or broken wire, or a componentmalfunction, could cause the propeller to rotate.
Fuel Quantity Indicators.............................. CHECK QUANTITYMaster Switch ..................................................... ................. OFFFuel Shutoff Valve ................................................................ ON
EMPENNAGE
Rudder Gust Lock ................................... ................... REMOVETail Tie-Down ..................................................... DISCONNECTControl Surfaces ............................................................ CHECK
freedom of movement and security
RIGHT WING
Aileron ........................................................ ................... CHECKfreedom of movement and security
Wing Tie-Down ................................................... DISCONNECTMain Wheel Tire ................................................. ........... CHECK
for proper inflation
Fuel Tank Sump Quick Drain Valve ................................ DRAINBefore first flight of the day and after each refuelling, use
sampler cup and drain small quantity of fuel from fuel tanksump quick-drain valve to check for water, sediment and
proper fuel grade.
Fuel Quantity ............................................... CHECK VISUALLYfor desired level
Fuel Filler Cap .................................................... ......... SECURE
-
8/9/2019 SOP Cessna 150-152
18/142
Standard Operating Procedures
Cessna 150/C152
Page 18 - 142 SOP C150/C152 - Issue 08
NOSE
Oil Level ........................................................................ CHECKdo not operate with less than four quarts. Fill to six quarts
for extended flight.
Strainer drain knob ............................................................ PULLto clear water and sediment.
Before first flight of the day and after each refuelling, pullout strainer drain knob for about four seconds to clear fuel
strainer of possible water and sediment. Check strainerdrain closed. If water is observed, the fuel system may
contain additional water, and further draining of the systemat the strainer, fuel tank sumps, and fuel line drain plug will
be necessary.
Propeller and Spinner .................................................... CHECKfor nicks and security
Carburettor Air Filter ...................................................... CHECKfor restrictions by dust or other foreign matter
Landing Light ...................................................... ........... CHECK
for condition and cleanlinessNose Wheel Strut and Tire ............................................ CHECK
for proper inflationNose Tie-Down ................................................... DISCONNECTStatic Source Opening (left side of fuselage) ................ CHECK
for stoppage
LEFT WING
Main Wheel Tire ................................................. ........... CHECKfor proper inflation
Fuel tank sump .................................................... DRAINBefore first flight of the day and after each refuelling, use
sampler cup and drain small quantity of fuel from fuel tanksump quick-drain valve to check for water, sediment and
proper fuel grade.Fuel Quantity ............................................... CHECK VISUALLY
for desired level
Fuel Filler Cap .................................................... ......... SECUREPitot Tube Cover ................................................ ........ REMOVEPitot Tube Opening ................................. ...................... CHECK
for stoppage
Stall Warning Opening................................................... CHECKfor stoppage
To check the system, place a clean handkerchief over thevent opening and apply suction; a sound from the warning
horn will confirm system operation.
Fuel Tank Vent Opening..................................... ........... CHECKfor stoppage
Wing Tie-Down ................................................... DISCONNECT Aileron ........................................................ ................... CHECKfreedom of movement and security
-
8/9/2019 SOP Cessna 150-152
19/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 19 - 142
NORMAL CHECKLIST C150
BEFORE STARTING ENGINE
Exterior Preflight ..................................................... COMPLETEPosition.......................................................................... . CLEARPapers ..................................................................... ON BOARDLoose Items ........................................................ ........ STOWEDSeats, Belts, Shoulder Harnesses .............. ADJUST and LOCKFuel Shutoff Valve ................................................................ ONRadios, Electrical Equipment ............................................... OFFBrakes ................................................................ TEST and SETCircuit breakers ....................................... .................. CHECK INStart Up (if applicable) .............................................. RECEIVEDBriefing ................................................................... COMPLETE
STARTING ENGINE (Temperatures Above Freezing)
Mixture............................................................................... RICHCarburettor Heat ............................................................ ... COLDMaster Switch ..................................................... .................. ONLights ................................................................................... SET Annunciators ...................................................... ........... CHECKPrime .......................................................... ....... AS REQUIRED
(Up to 3 strokes)
Throttle ............................................................. OPEN 1/4 INCHPropeller Area ............................................................... . CLEARIgnition Switch ......................................... ....................... START
(Release when engine starts)
Throttle ....................................................... .................. ADJUSTfor 1000 RPM or less
Oil Pressure ........................................................ ........... CHECKStarter Warning Light (if installed) ...................................... OUT Alternator Output ........................................................... CHECK
BEFORE TAXI
Avionics .............................................................. ................. SETFlight Instruments .......................................................... ...... SETFlaps.............................................................................. UP SETTime .............................................................................. NOTED
TAXI
Brakes ...................................................................... CHECKEDGyro Instruments and Compass ............................... CHECKED
-
8/9/2019 SOP Cessna 150-152
20/142
Standard Operating Procedures
Cessna 150/C152
Page 20 - 142 SOP C150/C152 - Issue 08
BEFORE TAKEOFF
Parking Brake ..................................................... ................. SETCabin Doors ................................. ............................. LATCHEDFlight Controls ......................................... FREE and CORRECTFlight Instruments .......................................................... ...... SETElevator Trim ............................................................. TAKEOFFFuel Shutoff Valve ................................................................ ONMixture.................................................. RICH (below 3000 feet)Engine Instruments ....................................................... CHECKBack Area ........................................................... ............ CLEARBrakes ........................................................................... ...... SETThrottle .............................................................. ....... 1700 RPMMagnetos ............................................................ ........... CHECK
(RPM drop should not exceed 150 RPM on either magnetoor 75 RPM differential between magnetos)
Carburettor Heat ............................................................ CHECK(for RPM drop)
Engine Instruments and Ammeter ................................. CHECK
Suction Gage ...................................................... ........... CHECKThrottle ................................................................. CHECK IDLEThrottle .............................................................. 1000 RPM SETFlight instruments and Radios ............................................. SETFlashing Beacon, Navigation Lights and/or Strobe Lights...........................................................................ON as requiredThrottle Friction Lock .................................................... ADJUST
Wing Flaps ............................................................................. 0 Brakes ....................................................................... RELEASE
RUNWAY ITEMS
Pitot Heat ............................................................ .................. ONLights ................................................................................... SETCarburettor Heat ............................................................ ...... OFF
Transponder ....................................................... ...... - - - - SETRunway heading ............................................................ CHECKTime .............................................................................. CHECKTake-Off Clearance(if applicable) ............................. RECEIVED
TAKEOFF
NORMAL TAKE-OFFWing Flaps ..............................................................................0ºCarburettor Heat ............................................................ ... COLDThrottle ................................................................... FULL OPENElevator Control ..................... LIFT NOSE WHEEL (at 55 MPH)Climb Speed ....................................................... .... 70 - 80 MPH
MAXIMUM PERFORMANCE TAKE-OFF
Wing Flaps ............................................................................. 0°Carburettor Heat ............................................................ ... COLDBrakes ........................................................................... ... HOLDThrottle ................................................................... FULL OPENBrakes ....................................................................... RELEASEElevator Control ....................................... SLIGHTLY TAIL LOWClimb Speed ....................................................... ........... 70 MPH
(with obstacles ahead)
SHORT FIELD TAKE-OFFWing Flaps ........................................................................... 10°Carburettor Heat ............................................................ ... COLDBrakes ........................................................ .................... APPLYThrottle ................................................................... FULL OPENBrakes ....................................................................... RELEASEElevator Control ....................................... SLIGHTLY TAIL LOWClimb Speed ....................................................... ........... 70 MPH
(Until all obstacles are cleared)
Wing Flaps ................................................................ RETRACT
-
8/9/2019 SOP Cessna 150-152
21/142
-
8/9/2019 SOP Cessna 150-152
22/142
Standard Operating Procedures
Cessna 150/C152
Page 22 - 142 SOP C150/C152 - Issue 08
LANDING
NORMAL LANDING Airspeed ................................................. 70-80 MPH (flaps UP)Wing Flaps ..... .......................... AS DESIRED (below 100 MPH) Airspeed ...........................................60-70 MPH (flaps DOWN)Touchdown ............................................ MAIN WHEELS FIRSTLanding Roll .......................... LOWER NOSE WHEEL GENTLYBraking ................................................... MINIMUM REQUIRED
SHORT FIELD LANDING Airspeed .................................................. 70-80 MPH (flaps up)Wing Flaps ........................... .................... 30° (below 100 MPH) Airspeed ..................................................... MAINTAIN 70 MPHPower .............................................. ............................ REDUCE
to idle as obstacle is cleared
Touchdown ............................................ MAIN WHEELS FIRSTBrakes ............................................................ APPLY HEAVILYWing Flaps ..... ........................................................... RETRACT
BALKED LANDINGThrottle .............................................................. .... FULL OPENCarburettor Heat ............................................................ ... COLDWing Flaps ..... ................................................. RETRACT to 20° Airspeed ............................................................. ........... 65 MPHWing Flaps ................................... ................. RETRACT(slowly)
AFTER LANDING
Pitot Heat ............................................................ ................. OFFLights ................................................................................... SETWing Flaps ........................... ................................................. UPCarburettor Heat ............................................................ ... COLDTransponder ....................................................... ........ - - - SET
Time .............................................................................. CHECK
SECURING AIRCRAFT
Parking Brake ..................................................... ................. SETRadios, Electrical Equipment ............................................... OFFMixture............................................................... IDLE CUT OFF
(Pulled full out)
All Switches ........................................................ ................. OFFIgnition Switch ..................................................................... OFFMaster Switch ..................................................... ................. OFFFuel Shut Off Valve ....................................................... ...... SETControl Lock ................................................................ INSTALLWindows ............................................................. ......... CLOSEDTime .............................................................................. NOTED
STALL
Briefing ................................................................... COMPLETESafety Belts ........................................................ ..... FASTENEDLoose Items ........................................................ ........ STOWEDEngine Instruments ....................................................... CHECKCarburettor Heat ............................................................ ....... ONMixture............................................................................... RICH APOS ......................................................... ................... CHECK
AFTER STALL
Flaps.............................................................................. UP SETCarburettor Heat ............................................................ ...... OFFThrottle ................................................................ ....... - - - SETMixture........................................................................ - - - SETEngine Instruments ....................................................... CHECKDirectional Gyro ............................................................. CHECKOrientation .......................................................... ........... CHECK
-
8/9/2019 SOP Cessna 150-152
23/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 23 - 142
5.2 EXPANDED NORMAL CHECKLIST C150: PH-RUD/NOD/HVP
BEFORE STARTING ENGINE
(This checklist shall be performed after checking the weather and the crew briefing and before start up.)
Exterior Preflight………………. COMPLETE See AOM/POH supplemented as follows: When removing control wheel
lock, check free movement ofcontrols, and full travel of trim tab.
If draining is applicable, drain firsttanks and then strainer.
When turning master switch on,check proper working of beaconlight and if mandatory for flightalso landing light. For other lightsthe check at daily inspection issufficient.
Position ..……………………….. CLEAR Check that the aircraft position is free ofobstacles and is free to taxi out to taxi-way.
Papers....................................... ON BOARD Check OM for mandatory papers.
Loose items ............................ STOWED No heavy objects shall be left loose to avoidrisk of injuries to the occupants or damageto the aircraft in turbulence or during airexercises.
Seats, Belts, ShoulderHarnesses.................................. ADJUSTED and LOCK Adjust your seat and pedals in the same
locked position. Check Shoulder Harnessesof all occupants are fastened.Make sure passengers know how to close,adjust and open the shoulder harnesses.
Fuel Shutoff valve.................... ON
Radios, Electrical Equipment. OFF
Brakes…………………………… TEST AND SET
Circuit breakers...................... CHECK IN Check that circuit breaker are in. Fuses onlyhave to be checked if one of the systems ismal functioning. The C152 and C150F havecircuit breakers only, the C150 has onecircuit breaker and further fuses. Circuitbreakers may not be reset.
Start up (if applicable) RECEIVED If applicable.
Briefing................................... COMPLETED
-
8/9/2019 SOP Cessna 150-152
24/142
Standard Operating Procedures
Cessna 150/C152
Page 24 - 142 SOP C150/C152 - Issue 08
STARTING ENGINE (This checklist shall be performed just before engine start.)
Mixture.................................... RICH
Carburettor Heat.................... COLD Check carburettor heat is COLD.
Master Switch…………………. ON
Lights.......................... SET Set warning light for indicating starting up of
engine or running engine. Set NAV lightsduring night or visibility less than 5000 m.
Annunciators................... CHECK Check all annunciators working properly (ifpossible). The starter warning light can beof the "push to test" type. Push the light on
the brim, it will then illuminate. Releasingthe light will leave it out.When the starter warning light remains ONafter starting the engine immediately shutdown the engine.
Prime...................................... AS REQUIRED Before the first flight of the day the first(Up to 3 strokes) stroke may only be half filled.
Three strokes will be required for the firstflight of the day or if time betweensucceeding flights exceeds 1 hour,otherwise one stroke will be sufficient.Lock primer after priming.
Throttle.................................... OPEN 1/2 INCH
Propeller area........................ CLEAR
Ignition switch…………………. START Turn starter key to "START", release as(Release when engine soon as the engine is picking up.Starts) Starter engine operation is limited to
30 seconds ON / 30 seconds OFF30 seconds ON / 30 seconds OFF30 seconds ON / 3 minutes OFF.
Throttle.................…………... ADJUSTFor 1000 RPM or less
Oil pressure............................ CHECK Pressure indication should be rising withwarm temperature within 30 seconds, invery cold weather within 60 seconds.If pressure indication is not showing withinthis time, shut down the engine.
Starter warning light ............. OUT Check starter warning light is OUT.(If installed) If starter warning light remains illuminated:
shut down the engine.
Alternator output................... CHECK Check ammeter shows load. If ammeter isstill indicating a discharge switch master
switch OFF, both sides, and then ON again.If ammeter is still indicating a dischargeshut down the engine and inform OPS.
-
8/9/2019 SOP Cessna 150-152
25/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 25 - 142
BEFORE TAXI(This checklist shall be performed after engine start en before taxi.)
Avionics.................................... SET Avionics panel: Select intercom switch to "phone" if you are using headphones,
otherwise select intercom switch to "speaker".The switches on the avionics panel have three positions:Speaker-OFF-PhoneSpeaker = UP, OFF = middle, Phone = down.Select mic-selector to COM-1 (there is only one com)Select COM to phoneSelect NAV OFFSelect ADF OFFSelect DME OFFSelect Marker OFF.
Avionics Master Switch Select ONIf there is no avionics master switch, turn individual avionics ON.
COM Select required COM station,Test volume with squelch button, adjust volume to desired audio level,Select a suitable stby. Frequency.
NAV Select a NAV beacon. If you are receiving its signal on the ground:Identify the beacon: set NAV on the avionics panel to phone, checkmorse code, select NAV on avionics panel to OFF.Check current radial, turn course selector 10 degrees to the left andcheck full scale deflection to the left. Turn course selector 90 degreesto the left check TO/FROM change, select course selector 10 degrees
to the right of centre radial, check still full scale deflection, to the right.Turn on to original radial, check indicated radial centred.If for first part of flight a radial shall be flown, select this radial.Select a suitable beacon as stby.
ADF Select a NDB.Select ADF on the avionics panel to "phone" and adjust volume todesired audio level. Identify its morse code. Select ADF on avionicspanel OFF.Set ADF in ANT mode, check ADF pointer will go to 90 degreesparked position.Set ADF in ADF mode, check ADF pointer returns to current QDMthrough shortest way.
Select NDB frequency for departure.
DME Select a DME frequency.Select DME on avionics panel to "phone" and adjust volume to desiredaudio level. Identify its morse code. (might take some time!) SelectDME on avionics panel to OFF.
Transponder Set transponder to designated frequency (if no designated frequencyreceived: set to VFR code) and STBY.
-
8/9/2019 SOP Cessna 150-152
26/142
Standard Operating Procedures
Cessna 150/C152
Page 26 - 142 SOP C150/C152 - Issue 08
Flight instruments ................... SET Check OAT in accordance with ATIS.Check Air Speed Indicator indicates zero.Check Attitude indicator shows level flight.
Check Altitude indicator shown field.elevation, set to QNH.Check Vertical Speed Indicator zero.Check Directional Gyro is aligned withcompass.Check Turn & Bank indicator shows no turn,ball in the middle if aircraft is on levelground.
Flaps....................................... UP SET Select flaps UP in stages, check if flapposition stops work, or that flap-selectorstop works.
Time........................................ NOTED This is the Off-blocks time to be noted in theaircraft journal.
TAXI(This checklist items shall be performed during taxi. The checklist at the holding position beforethe run up.)
Brakes.................................... CHECKED Check gently the brake pressure on thepedals, but do not stop the aircraft
Gyro Instruments and Compass... CHECKED Try to make the turns during taxi-route.Check in a left turn the turn and bank
indicator with needle to the left and ball tothe right. The Directional Indicator shouldbe decreasing and Compass decreasingand the Attitude Indicator should be steady.Visa Versa for the right turn.
BEFORE TAKE-OFF
(This checklist shall be performed at the holding position, preferably into the wind just beforedeparture. If possible leave room for other aircraft to pass.)
Parking Brake.......................... SET
Cabin Doors……………………. LATCHED
Flight controls......................... FREE AND CORRECT Yoke fully forward and left. Check leftaileron up and right aileron down.Check elevator down.Yoke fully forward and right. Check rightaileron up and left aileron down. Returnyoke to neutral.Pull yoke fully aft. Check elevator up.Check rudder free moving. Do not give fulldeflection on rudder since that would onlywear out the bungee system.
Flight instruments ................... SET Perform a check on all flight instruments
if they are set correct.
Elevator Trim............................ TAKE-OFF Normal trim position is indicated with a line.In case of a forward centre of gravity trim
-
8/9/2019 SOP Cessna 150-152
27/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 27 - 142
one stroke nose up, for a aft centre ofgravity trim one stroke nose down.
Fuel Shutoff Valve……………… ON
Mixture..................................... RICH (below 3000 feet) In case of high elevation airfield, see AOM/POH.
Engine Instruments……………. CHECK Check engine instruments stay in the greenarc.
Back Area.................................. CLEAR Check that there are no aircraft, glider, orpeople standing on short distance behindyou.
Brakes........…………………….. SET
Throttle..................................... 1700 RPM
Magnetos................................. CHECK (RPM drop should not exceed 150 RPMon either magneto or 75 RPM differentialbetween magnetos)C150 max drop 150 RPM, max diff 75 RPMCheck first right, then left magnetoSelect Magnetos to BOTH after test.
Carburettor heat....................... CHECK (for RPM drop) Select carburettor heat ON and leave ONfor 20-30 seconds. Note drop in RPM.In case of icing the RPM will increase.
Leave carb. heat ON until rpm remainsstable
Engine Instruments and Ammeter CHECK Check engine instruments stay in the green
arc.Check ammeter is indicating a needle widthabove zero. Battery should normally becharged by now.If in doubt check proper alternator functionby switching ON the landing light for3 to 5 seconds. The ammeter will remain
within a needle width of its original position.If ammeter is still indicating a marked
charge, or shows a significant drop whenlanding light is ON either alternator and/orbattery has a malfunction.
Suction Gage............................ CHECK Suction indication should indicate between4,6 to 5,4 inches of mercury.If indication is below 4,6 expect AI and DGto malfunction.
Throttle ………………………… CHECK IDLE Check idle RPM between approximately500 and 800 RPM. RPM values above 1000are not to be accepted.
Throttle………………………….. 1000 RPM SET
Flight instruments and Radios........SET
-
8/9/2019 SOP Cessna 150-152
28/142
Standard Operating Procedures
Cessna 150/C152
Page 28 - 142 SOP C150/C152 - Issue 08
Flashing Beacon, Navigation
Lights And/or Strobe Lights..... ON as required Flashing Beacon on, strobe lights on,Navigation lights on when visibility becomesless than 5000 m.
Throttle friction Lock.............. ADJUST Set friction so that you can easily move thethrottle, but it will not move by itself.
Wing flaps............................... 0
Brakes........…………………….. RELEASE
RUNWAY ITEMS
(These checklist items shall be performed by memory. In case of single pilot operation theseitems shall be performed standing still. Line up clearance(if applicable) must be received.)
Pitot heat................................. ON Pitot heat should be on during flight
Lights....................................... SET Select taxi light off, landing light ON, strobelights ON
Carburettor heat..................... OFF
Transponder ........................... - - - SET Select transponder to ALT, if applicable
Runway heading..................... CHECK Check compass indicating + published
runway magnetic track and DG still aligned
with compass.
Time......................................... CHECK Start timer . At this time your flight plan willbe activated the start of the navigation plan.Note time when circumstances permit.
Take-off clearance.................. RECEIVED If applicable.
TAKE-OFF
(This checklist shall be performed by memory during take-off.)
NORMAL TAKE-OFFWing flaps…………………….. 0˚
Carburettor Heat…………….. COLD
Throttle………………………... FULL OPEN
Elevator Control……………... LIFT NOSE WHEEL at 55 MPH
Climb speed………………….. 70 – 80 MPH
MAXIMUM PERFORMANCE TAKE-OFFWing Flaps................................ 0°
Carburettor Heat..................... COLD
Brakes....................................... APPLY
Throttle..................................... FULL OPEN
-
8/9/2019 SOP Cessna 150-152
29/142
-
8/9/2019 SOP Cessna 150-152
30/142
Standard Operating Procedures
Cessna 150/C152
Page 30 - 142 SOP C150/C152 - Issue 08
Engine instruments................ CHECK Check oil pressure and oil temperatureindications are within green arc.
Throttle..................................... FULL OPEN
Mixture ..................................... RICH Lean according POH.
Landing light............................ SET Normally off, but Subject CaptainsDiscretion.
CRUISE(This checklist shall be performed after levelling off for cruise.)
Engine instruments................ CHECKED Check oil pressure and oil temperatureindications are within green arc.
Power……………………………. 1900 to 2550 RPM(No more than 75%)
Elevator Trim……………………. ADJUST
Mixture..................................... LEAN For airwork exercise mixture will be rich.
Otherwise mixture should be leanedaccording AOM/POH.
Fuel Quantity…………………… CHECK Check remaining fuel with calculated fuel
Directional Gyro...................... CHECK Check DG is aligned with compass.
DESCENT(This checklist shall be performed after starting a descent.) Altimeter................................. SET When descending to an altitude set
altimeter to local or regional QNH.
Engine instruments............... CHECKED Check oil pressure and oil temperatureindications are within green arc.
Mixture.................................... SET When flying with lean mixture enrich mixture
during descend. Often it will be possible toselect full rich. When starting descent from
high altitude, selecting full rich mixturemight cause rough running engine.
Carburettor Heat...................... ON Select carburettor heat ON whenever you
fly at low RPM settings
BEFORE LANDING(This checklist shall be performed when cleared to an altitude (if applicable) and inbound for a landing.
Items may be delayed until on final, but must be completed before reaching 500’ AAL. During circuit training Stella items must be omitted, except for the items “ENGINE INSTRUMENTS”, “BRIEFING” and “FLAPS”.)
Altimeter................................. - - - SET Set altimeter to local QNH or to regionalQNH.
Directional Gyro...................... CHECK Check DG is aligned with compass.
-
8/9/2019 SOP Cessna 150-152
31/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 31 - 142
Engine instruments.............. CHECK Check oil pressure and oil temperatureindications are within green arc.
Seats, Belts, Harnesses……... ADJUST AND LOCK
Mixture.................................... RICH
Carburettor heat..................... ON Selecting carburettor heat ON reduces rpm(Apply full heat before with approximately 100 rpm. Reset throttleClosing throttle) to desired rpm.
Landing light.......................... ON
Briefing…………………………. COMPLETED
(The check of the items below shall be completed when established on final)
Flaps.......................................... - - - SET The check of this item shall be performedwhen established on final
LANDING(This checklist shall be performed by memory during landing.)
NORMAL LANDING
Airspeed ..................................... 70-80 MPH (flaps UP)
Wing Flaps.................... AS DESIRED (below 100 MPH)
Airspeed ................................. 60-70 MPH (flaps down)
Touchdown ................................ MAIN WHEELS FIRST
Landing Roll .............. LOWER NOSE WHEEL GENTLY
Braking ........................................ MINIMUM REQUIRED
SHORT FIELD LANDING
Airspeed ...................................... 70-80 MPH (flaps up)
Wing Flaps.................................... 30° (below 100 MPH)
Airspeed .......................................... MAINTAIN 70 MPH
Power .............. REDUCE to idle as obstacle is cleared
Touchdown ................................ MAIN WHEELS FIRST
Brakes .................................................. APPLY HEAVILY
Wing Flaps...................................................... RETRACT
BALKED LANDING
Throttle ....................................................... FULL OPEN
-
8/9/2019 SOP Cessna 150-152
32/142
Standard Operating Procedures
Cessna 150/C152
Page 32 - 142 SOP C150/C152 - Issue 08
Carburettor Heat ................................................... COLD
Wing Flaps........................................... RETRACT to 20°
Airspeed ............................................................. 65 MPH
Wing Flaps......................................... RETRACT(slowly)
AFTER LANDING
(This checklist shall be performed by memory after vacating the runway. The checklist may beperformed rolling during single pilot operations but on straight taxiways only. The checklist shallthen be read when on the parking position.)
Pitot heat................................ OFF
Lights...................................... SET Select landing light OFF.Taxi light ON if so required. If no taxi light isavailable, use landing light instead.Navigation lights OFF, during night orvisibility less than 5000m navigation lightsremain ON.Strobe lights OFF
Wing Flaps............................. UP
Carburettor heat.................... COLD
Transponder.......................... SET Normally select transponder to STBY, if
applicable
Time......................................... NOTED Note time as end of flight.
SECURING AIRCRAFTThis checklist shall be performed when on parking position.)
Parking brake ........................ SET
Radios, Electrical equipment. OFF
Mixture................................... IDLE CUT OFF
(Pull full out)
All switches........................... OFF Except master switch.
Ignition Switch………………… OFF Before switching OFF ignition switch waituntil propeller has stopped and take keyout.
Master Switch......................... OFF
Fuel Shut Off Valve……………. - - - SET
Control lock............................ INSTALL Install control lock with red flap before theignition switch.
Windows................................... CLOSED Windows and doors shall be closed when
leaving the aircraft
-
8/9/2019 SOP Cessna 150-152
33/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 33 - 142
Time........................................ NOTED This is your ON BLOCK time and be notedin the aircraft journal.
PRE STALL(This checklist shall be performed after the stall briefing and just before the (stall) exercise.)
Briefing.................................. COMPLETE
Safety belts........................... FASTENED
Loose items…………………. STOWED
Engine instruments............. CHECKED Check oil pressure and oil temperatureindications are within green arc.
Carburettor heat................... ON
Mixture.................................. RICH
APOS…….............................. CHECKED
AFTER STALL(This checklist shall be performed when stabilized on altitude/level after the (stall) exercise.)
Flaps.................................... UP SET
Carburettor Heat................. OFF
Throttle............................... SET Set throttle to cruise rpm.
Mixture................................ SET
Engine instruments........... CHECK Check oil pressure and oil temperatureindications are within green arc.
Directional Gyro................. CHECK Check DG aligned with compass.
Orientation......................... CHECK Check position and direction.
-
8/9/2019 SOP Cessna 150-152
34/142
Standard Operating Procedures
Cessna 150/C152
Page 34 - 142 SOP C150/C152 - Issue 08
INTENTIONALLY LEFT BLANK
-
8/9/2019 SOP Cessna 150-152
35/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 35 - 142
5.3 CESSNA 152: PH-JVB/CDS/STQ/WEE
PREFLIGHT INSPECTION
Note:
Visually check airplane for general condition during walk-around inspection. In cold weather, remove evensmall accumulations of frost, ice or snow from wing, tail and control surfaces.
Also, make sure that control surfaces contain no internal accumulations of ice or debris. Prior to flight,check that pitot heater (if installed) is warm to touch within 30 seconds with battery and pitot heat switcheson.
If a night flight is planned, check operation of all lights, and make sure a flashlight is available.
CABIN
Control Wheel Lock .................................................... REMOVEIgnition Switch ..................................................................... OFFMaster Switch ..................................................... .................. ONFuel Quantity Indicators.............................. CHECK QUANTITYMaster Switch ..................................................... ................. OFFFuel Shutoff Valve ................................................................ ON
EMPENNAGE
Rudder Gust Lock ................................... ................... REMOVETail Tie-Down ..................................................... DISCONNECTControl Surfaces ............................................................ CHECK
freedom of movement and security
RIGHT WING
Aileron ........................................................ ................... CHECKfreedom of movement and security
Wing Tie-Down ................................................... DISCONNECTMain Wheel Tire ................................................. ........... CHECK
for proper inflation
Fuel Tank Sump Quick Drain Valve ................................ DRAINBefore first flight of the day and after each refuelling, use
sampler cup and drain small quantity of fuel from fuel tanksump quick-drain valve to check for water, sediment and
proper fuel grade.
Fuel Quantity .............................................. CHECK VISUALLYfor desired level
Fuel Filler Cap .................................................... ......... SECURE
-
8/9/2019 SOP Cessna 150-152
36/142
Standard Operating Procedures
Cessna 150/C152
Page 36 - 142 SOP C150/C152 - Issue 08
NOSE
Engine Oil Level ................................................. ........... CHECKdo not operate with less than four quarts. Fill to six quarts
for extended flight.Strainer Drain Knob ....................................................... .... PULL
to clear water and sedimentBefore first flight of the day and after each refuelling, pull
out strainer drain knob for about four seconds to clear fuelstrainer of possible water and sediment. Check strainerdrain closed. If water is observed, the fuel system may
contain additional water, and further draining of the systemat the strainer, fuel tank sumps, and fuel line drain plug will
be necessary.
Propeller and Spinner .................................................... CHECKfor nicks and security
Carburettor Air Filter ...................................................... CHECKfor restrictions by dust or other foreign matter
Landing Light(s) ............................................................. CHECK
for condition and cleanlinessNose Wheel Strut and Tire ............................................ CHECK
for proper inflationNose Tie-Down ................................................... DISCONNECTStatic Source Opening (left side of fuselage) ................ CHECK
for stoppage
LEFT WING
Main Wheel Tire ................................................. ........... CHECKfor proper inflation
Fuel Tank Sump ................................................. ............. DRAINBefore first flight of the day and after each refuelling, use
sampler cup and drain small quantity of fuel from fuel tanksump quick-drain valve to check for water, sediment and
proper fuel grade.Fuel Quantity ............................................... CHECK VISUALLY
for desired level
Fuel Filler Cap .................................................... ......... SECUREPitot Tube Cover ................................................ ........ REMOVEPitot Tube Opening ................................. ...................... CHECK
for stoppage
Stall Warning Opening................................................... CHECKfor stoppage
To check the system, place a clean handkerchief over thevent opening and apply suction; a sound from the warning
horn will confirm system operation.
Fuel Tank Vent Opening..................................... ........... CHECKfor stoppage
Wing Tie-Down ................................................... DISCONNECT Aileron ........................................................ ................... CHECKfreedom of movement and security
-
8/9/2019 SOP Cessna 150-152
37/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 37 - 142
NORMAL CHECKLIST
BEFORE STARTING ENGINE
Preflight Inspection ................................................. COMPLETEPosition.......................................................................... . CLEARPapers ..................................................................... ON BOARDLoose Items ........................................................ ........ STOWEDSeats, Belts, Shoulder Harnesses .............. ADJUST and LOCKFuel Shutoff Valve ................................................................ ONRadios, Electrical Equipment ............................................... OFFBrakes ................................................................ TEST and SETCircuit Breakers ......................................................... CHECK INStart Up (if applicable) .............................................. RECEIVEDBriefing ................................................................... COMPLETE
STARTING ENGINE (Temperatures Above Freezing)
Mixture............................................................................... RICHCarburettor Heat ............................................................ ... COLDPrime .......................................................... ....... AS REQUIRED
(Up to 3 strokes)
Throttle ............................................................. OPEN 1/2 INCHPropeller Area ............................................................... . CLEARMaster Switch ..................................................... .................. ONLights ................................................................................... SET Annunciators ...................................................... ........... CHECKIgnition Switch ......................................... ....................... START
(Release when engine starts)
Throttle ....................................................... .................. ADJUSTfor 1000 RPM or less
Oil Pressure ........................................................ ........... CHECKStarter Warning Light (if installed) ...................................... OUT Alternator Output ........................................................... CHECK
BEFORE TAXI
Avionics .............................................................. .................. ONFlight Instruments .......................................................... ...... SETFlaps.............................................................................. UP SETTime .............................................................................. NOTED
TAXI
Brakes ...................................................................... CHECKEDGyro Instruments and Compass ............................... CHECKED
-
8/9/2019 SOP Cessna 150-152
38/142
Standard Operating Procedures
Cessna 150/C152
Page 38 - 142 SOP C150/C152 - Issue 08
BEFORE TAKEOFF
Parking Brake ..................................................... ................. SETCabin Doors ........................................CLOSED and LATCHEDFlight Controls ......................................... FREE and CORRECTFlight Instruments .......................................................... ...... SETFuel Shutoff Valve ................................................................ ONMixture.................................................. RICH (below 3000 feet)Elevator Trim ............................................................. TAKEOFFEngine Instruments ....................................................... CHECKBack Area ........................................................... ............ CLEARThrottle .............................................................. ....... 1700 RPMMagnetos ............................................................ ........... CHECK
(RPM drop should not exceed 125 RPM on either magnetoor 50 RPM differential between magnetos)
Carburettor Heat ............................................................ CHECK(for RPM drop)
Engine Instruments and Ammeter ................................. CHECKSuction Gage ...................................................... ........... CHECK
Throttle ................................................................ ............... IDLEThrottle .............................................................. 1000 RPM SETRadios ........................................................................... ...... SETFlashing Beacon, Navigation Lights and/or Strobe Lights...........................................................................ON as requiredThrottle Friction Lock .................................................... ADJUSTFlaps........................................................................... - - - SETBrakes ....................................................................... RELEASE
RUNWAY ITEMS
Pitot Heat ............................................................ .................. ONLights ................................................................................... SETCarburettor Heat ............................................................ ...... OFFTransponder ....................................................... ........ - - - SET
Runway Heading ........................................................... CHECKTime .............................................................................. CHECKTake-Off Clearance (if applicable) ............................ RECEIVED
TAKEOFF
NORMAL TAKE-OFFWing Flaps .................................................................... . 0º - 10ºCarburettor Heat ............................................................ ... COLDThrottle ................................................................... FULL OPENElevator Control ........................ LIFT NOSE WHEEL at 50 KIASClimb Speed ........................................................... 65 - 75 KIAS
SHORT FIELD TAKE-OFF
Wing Flaps ........................................................................... 10°Carburettor Heat ............................................................ ... COLDBrakes ........................................................ .................... APPLYThrottle ................................................................... FULL OPENMixture............................................................................... RICH
(Above 3000’, LEAN to obtain maximum RPM) Brakes ....................................................................... RELEASEElevator Control ....................................... SLIGHTLY TAIL LOWClimb Speed ....................................................... ........... 54 KIAS
(Until all obstacles are cleared)
Wing Flaps ..... ........................................................... RETRACTslowly after reaching 60 KIAS
AFTER TAKEOFF
Engine Instruments ....................................................... CHECKCarburettor Heat ............................................................ ...... OFFThrottle .............................................................................. FULLFlaps.............................................................................. UP SET
-
8/9/2019 SOP Cessna 150-152
39/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 39 - 142
ENROUTE CLIMB
Altimeter ............................................................. ......... - - - SET Airspeed ............................................................. .... 70 - 80 KIAS
NOTE:If a maximum performance climb is necessary, use speedsshown in the Rate of Climb chart in POH section 5
Engine Instruments ....................................................... CHECKThrottle ................................................................... FULL OPENMixture..................................................... RICH below 3000 feet
LEAN for maximum RPM above 3000 feet
Landing Light ...................................................... ......... - - - SET
CRUISE
Engine Instruments ....................................................... CHECKPower ............................................................ 1900 – 2550 RPM
(No more than 75%)
Elevator Trim ................................................................ ADJUSTMixture.............................................................................. LEANFuel Quantity ................................................................. CHECKDirectional Gyro ............................................................. CHECK
DESCENT
Altimeter ............................................................. ........ - - - SETEngine Instruments ....................................................... CHECKMixture ................................. ............................................... SETCarburettor Heat ............................................................ ....... ON
BEFORE LANDING
Altimeter ............................................................. ........ - - - SET
Directional Gyro ............................................................. CHECKEngine Instruments........................................................ CHECKSeats, Belts, Harnesses ............................ ADJUST AND LOCKMixture........................................................ ....................... RICHCarburettor Heat ............................................................ ....... ON
(Apply full heat before closing throttle)
Landing light ......................................................................... ONBriefing ................................................................ .COMPLETEDFlaps ........................................................... ................. - - - SET
-
8/9/2019 SOP Cessna 150-152
40/142
-
8/9/2019 SOP Cessna 150-152
41/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 41 - 142
5.4 EXPANDED NORMAL CHECKLIST C152: PH-JVB/CDS/STQ/WEE
BEFORE STARTING ENGINE
(This checklist shall be performed after checking the weather and the crew briefing and before start up.)
Preflight Inspection...…………. COMPLETE See AOM/POH supplemented as follows: When removing control wheel
lock, check free movement ofcontrols, and full travel of trim tab.
If draining is applicable, drain firsttanks and then strainer.
When turning Master Switch on,check proper working of beaconlight and if mandatory for flightalso landing light. For other lightsthe check at daily inspection issufficient.
Position ..……………………….. CLEAR Check that the aircraft position is free ofobstacles and is free to taxi out to taxi-way.
Papers....................................... ON BOARD See OM for mandatory papers on board.
Loose items ............................ STOWED No heavy objects shall be left loose to avoidrisk of injuries to the occupants or damageto the aircraft in turbulence or during airexercises.
Seats, Belts, Shoulder Harnesses ADJUSTED and LOCK Adjust your seat and pedals in the samelocked position. Check Shoulder Harnessesof all occupants are fastened.Make sure passengers know how to close,adjust and open the shoulder harnesses.
Fuel Shutoff Valve...................... ON
Radios, Electrical Equipment... OFF
Brakes…………………………… TEST AND SET
Circuit Breakers.......................... CHECK IN Check that circuit breaker are in. Fuses onlyhave to be checked if one of the systems ismal functioning. The C152 and C150F havecircuit breakers only, the C150 has onecircuit breaker and further fuses. Circuitbreakers may not be reset.
Start up (if applicable).……… RECEIVED If applicable
Briefing................................... COMPLETED
-
8/9/2019 SOP Cessna 150-152
42/142
Standard Operating Procedures
Cessna 150/C152
Page 42 - 142 SOP C150/C152 - Issue 08
STARTING ENGINE (This checklist shall be performed just before engine start.)
Mixture.................................... RICH
Carburettor Heat..................... COLD Check carburettor heat is COLD.
Prime...................................... AS REQUIRED Before the first flight of the day the firststroke may only be half filled.Three strokes will be required for the firstflight of the day or if time betweensucceeding flights exceeds one hour,otherwise one stroke will be sufficientLock primer after priming.
Throttle.................................... OPEN 1/2 INCH
Propeller Area......................... CLEAR
Master switch…………………… ON
Lights.......................... SET Set warning light for indicating starting up ofengines or running engines. Set NAV lightsduring night or visibility less than 5000 m.
Annunciators CHECK Check all annunciators working properly (if
possible). The starter warning light is of the"push to test" type. Push the light on thebrim, it will then illuminate. Releasing the
light will leave it out.When the starter warning light remains ONafter starting the engine immediately shutdown the engine.
Ignition switch…………………. START Turn starter key to "START", release assoon as the engine is picking up.Starter engine operation is limited to30 seconds ON / 30 seconds OFF30 seconds ON / 30 seconds OFF30 seconds ON / 3 minutes OFF.
Throttle.................…………... ADJUST 1000 RPM or less.
Oil pressure............................ CHECK Pressure indication should be rising withwarm temperature within 30 seconds, invery cold weather within 60 seconds.If pressure indication is not showing withinthis time, shut down the engine.
Starter warning light ............. OUT Check starter warning light is OUT.(if installed) If starter warning light remains illuminated:
shut down the engine.
Alternator Output................... CHECK Check ammeter shows load. If ammeter isstill indicating a discharge switch master
switch OFF, both sides, and than ON again.If ammeter is still indicating a dischargeshut down the engine and inform OPS.
-
8/9/2019 SOP Cessna 150-152
43/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 43 - 142
BEFORE TAXI(This checklist shall be performed after engine start en before taxi.)
Avionics.................................... ON Avionics panel: Select intercom switch to "phone" if you are using headphones,
otherwise select intercom switch to "speaker".The switches on the avionics panel have three positions:Speaker-OFF-PhoneSpeaker = UP, OFF=middle, Phone = down.Select mic-selector to COM-1 (there is only one com)Select COM to phoneSelect NAV OFFSelect ADF OFFSelect DME OFFSelect Marker OFF.
Avionics Master Switch Select ONIf there is no Avionics Master switch, turn individual avionics ON.
COM Select required COM stationTest volume with squelch button, adjust volume to desired audio level.Select a suitable stby. frequency
NAV Select a NAV beacon. If you are receiving its signal on the ground:Identify the beacon: set NAV on the avionics panel to phone, checkmorse code, select NAV on avionics panel to OFF.Check current radial, turn course selector 10 degrees to the left andcheck full scale deflection to the left. Turn course selector 90 degreesto the left check TO/FROM change, select course selector 10 degrees
to the right of centre radial, check still full scale deflection, to the right.Turn on to original radial, check indicated radial centred.If for first part of flight a radial shall be flown, select this radial.Select a suitable beacon as stby.
ADF Select a NDB.Select ADF on the avionics panel to "phone" and adjust volume todesired audio level. Identify its morse code. Select ADF on avionicspanel OFF.Set ADF in ANT mode, check ADF pointer will go to 90 degreesparked position.Set ADF in ADF mode, check ADF pointer returns to current QDMthrough shortest way.
Select NDB frequency for departure.
DME Select a DME frequency.Select DME on avionics panel to "phone" and adjust volume to desiredaudio level. Identify its morse code. (might take some time!) SelectDME on avionics panel to OFF.
Transponder Set transponder to designated frequency (if no designated frequencyreceived: set to VFR code) STBY.
-
8/9/2019 SOP Cessna 150-152
44/142
Standard Operating Procedures
Cessna 150/C152
Page 44 - 142 SOP C150/C152 - Issue 08
Flight instruments ................... SET Check OAT in accordance with ATIS.Check Air Speed Indicator indicates zero.Check Attitude indicator shows level flight.
Check Altitude indicator shown field.elevation, set to QNH.Check Vertical Speed Indicator zero.Check Directional Gyro is aligned withcompass.Check Turn & Bank indicator shows no turn,ball in the middle if aircraft is on levelground.
Flaps....................................... UP SET Select flaps UP in stages, check if flapposition stops work, or that flap-selectorstop works.
Time........................................ NOTED This is the Off-blocks time to be noted in theaircraft journal.
TAXI(This checklist items shall be performed during taxi. The checklist at the holding position beforethe run up.)
Brakes.................................... CHECKED Check gently the brake pressure on thepedals, but do not stop the aircraft
Gyro instruments and Compass CHECKED Try to make the turns during taxi-route.Check in a left turn the turn and bankindicator with needle to the left and ball to
the right. The Directional Indicator shouldbe decreasing and Compass decreasingand the Attitude Indicator should be steady.Visa Versa for the right turn.
BEFORE TAKE-OFF (This checklist shall be performed at the holding position, preferably into the wind just beforedeparture. If possible leave room for other aircraft to pass.)
Parking Brake.......................... SET
Cabin Doors……………………. CLOSED and LATCHED
Flight Controls......................... FREE AND CORRECT Yoke fully forward and left. Check leftaileron up and right aileron down.Check elevator down.Yoke fully forward and right. Check rightaileron up and left aileron down. Returnyoke to neutral.Pull yoke fully aft. Check elevator up.Check rudder free moving. Do not give fulldeflection on rudder since that would onlywear out the bungee system.
Flight Instruments……………... SET
Fuel Shutoff Valve……………… ON
Mixture..................................... RICH (below 3000 ft) In case of high elevation airfield, see AOM/POH.
-
8/9/2019 SOP Cessna 150-152
45/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 45 - 142
Elevator Trim............................ TAKE-OFF Normal trim position is indicated with a line.In case of a forward centre of gravity trimone stroke nose up, for a aft centre of
gravity trim one stroke nose down.Engine Instruments……………. CHECK Check engine instruments stay in the greenarc.
Back area.................................. CLEAR Check that there are no aircraft, glider, orpeople standing on short distance behindyou.
Throttle 1700 RPM
Magnetos................................. CHECK C152 max drop 125 rpm, max diff 50 RPMCheck first right, then left magnetoSelect Magnetos to BOTH after test.
Carburettor heat....................... CHECK Select carburettor heat ON and leave ONfor 20-30 seconds. Note drop in RPM.In case of icing the RPM will increase.Leave carburettor heat ON until RPMremains stable.
Engine Instruments andAmmeter.................................... CHECK Check engine instruments stay in the green
arc.
Suction Gage............................ CHECK Suction indication should indicate between4,6 to 5,4 inches of mercury.
If indication is below 4,6 expect AI and DGto malfunction. Malfunction of gyro suctionshall be reported to operations.
Throttle ………………………… IDLE Check idle rpm between approximately500 and 800 RPM.RPM values above 1000 are not to beaccepted. Return to home base. Informoperations.
Throttle………………………….. 1000 RPM SET
Radios SET
Flashing Beacon, NavigationLights and/or Strobe Lights.... ON as required
Throttle friction lock............... ADJUST Set friction so that you can easily move thethrottle, but it will not move by itself.
Flaps……….............................. - - - SET
Safety belts……………………… FASTENED
Briefing...................................... COMPLETED Brief amendments by ATC.
Brakes…………………………….. RELEASE
-
8/9/2019 SOP Cessna 150-152
46/142
Standard Operating Procedures
Cessna 150/C152
Page 46 - 142 SOP C150/C152 - Issue 08
RUNWAY ITEMS(These checklist items shall be performed by memory. In case of single pilot operation theseitems shall be performed standing still. Line up clearance(if applicable) must be received.)
Pitot heat................................. ON Pitot heat should be on during flight
Lights....................................... SET Select taxi light off, landing light ON, strobelights ON
Carburettor heat...................... OFF
Transponder ........................... - - - SET Select transponder to ALT, if applicable(= mode A + C).
Runway Heading..................... CHECK Check compass indicating + publishedrunway magnetic track and DG still aligned
with compass.
Time......................................... CHECK Start timer . At this time your flight plan willbe activated the start of the navigation plan.Note time when circumstances permit.
Take-off clearance.................. RECEIVED(If applicable)
TAKE-OFF(This checklist shall be performed by memory during take-off.)
NORMAL TAKE-OFF
Wing flaps…………………….. 0˚-10˚
Carburettor Heat…………….. COLD
Throttle………………………... FULL OPEN
Elevator Control……………... LIFT NOSE WHEEL (at 50 KIAS)
Climb speed………………….. 65-75 KIAS
SHORT FIELD TAKE-OFF
Wing flaps…………………….. 10˚
Carburettor Heat…………….. COLD
Brakes ………………………… APPLY
Throttle………………………… FULL OPEN
Elevator Control……………... SLIGHTLY TAIL LOW
Climb speed………………….. 54 KIAS
Wing Flaps……………………. RETRACT Slowly after reaching 60 KIAS
-
8/9/2019 SOP Cessna 150-152
47/142
-
8/9/2019 SOP Cessna 150-152
48/142
Standard Operating Procedures
Cessna 150/C152
Page 48 - 142 SOP C150/C152 - Issue 08
DESCENT(This checklist shall be performed after starting a descent.) Altimeter................................. SET When descending to an altitude set
altimeter to local or regional QNH.
Engine instruments............... CHECKED Check oil pressure and oil temperatureindications are within green arc.
Mixture.................................... SET When flying with lean mixture enrich mixtureduring descend. Often it will be possible toselect full rich. When starting descent fromhigh altitude, selecting full rich mixturemight cause rough running engine.
Carburettor heat...................... ON Select carburettor heat ON whenever youfly at low RPM settings .
BEFORE LANDING(This checklist shall be performed when cleared to an altitude (if applicable) and inbound for a landing.Items may be delayed until on final, but must be completed before reaching 500’ AAL. During circuit training Stella items must be omitted, except for the items “ENGINE INSTRUMENTS”, “BRIEFING” and “FLAPS”.)
ATIS......................................... RECEIVED Make sure the complete ATIS is receivedbefore entering the CTR or at least 5minutes before starting the approach.
Altimeter................................. - - - SET Set altimeter to local QNH or to regionalQNH.
Directional gyro..................... CHECK DG is aligned with compass.
Engine instruments.............. CHECK Check oil pressure and oil temperature
indications are within green arc.
Seats, Belts, Harnesses……... ADJUST AND LOCK
Mixture.................................... RICH
Carburettor heat.................... ON Selecting carburettor heat ON reduces rpm(Apply full heat with approximately 100 rpm. Reset throttleBefore closing throttle) to desired rpm.
Landing light.......................... ON
Briefing…………………………. COMPLETED
(The check of the items below shall be completed when established on final)
Flaps.......................................... - - - SET The check of this item shall be performed
when established on final
LANDING(This checklist shall be performed by memory during landing.)
NORMAL LANDING
Airspeed………………………. 60-70 KIAS (flaps up)
Wing Flaps....………………… AS DESIRED (below 85 KIAS)
-
8/9/2019 SOP Cessna 150-152
49/142
Standard Operating Procedures
Cessna 150/C152
SOP C150/C152 - Issue 08 Page 49 - 142
Airspeed………………………. 55-65 KIAS (flaps up)
Touchdown…………………… MAIN WHEEL FIRST
Landing Roll…………………. LOWER NOSE WHEEL GENTLY
Braking………………………... MINIMUM REQUIRED
SHORT FIELD LANDING
Airspeed………………………. 60-70 KIAS (flaps up)
Wing Flaps....………………… 30˚
Airspeed………………………. MAINTAIN 54 KIAS (flaps up)
Power………………………….. REDUCE
Touchdown…………………… MAIN WHEEL FIRST
Braking………………………... APPLY HEAVILY
Wing Flaps……………………. RETRACT
BALKED LANDING
Throttle………………………… Full open
Carburettor Heat........……….. COLD
Wing Flaps……………………. RETRACT TO 20˚
Airspeed………………………. 65 MPH
Wing Flaps……………………. RETRACT (slowly)
AFTER LANDING(This checklist shall be performed by memory after vacating the runway. The checklist may beperformed rolling during single pilot operations but on straight taxiways only. The checklist shallthen be read when on the parking position.)
Pitot heat................................ OFF
Lights...................................... SET Select landi