-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 1/15
Type text to search here...
Home > EIGRP OSPF Redistribution Sim
EIGRP OSPF Redistribution Sim
February 26th, 2012 in LabSim Go to comments
Question: (Hope someone will contribute the detailed requirement of this sim!)
Some information I have gathered so far:
R2 is an ASBR for EIGRP 100 and OSPF AREA 24
R3 is an ASBR for EIGRP 100 and OSPF AREA 34
[note: so there are TWO separate areas on TWO separate ASBRS
thus you need to do redistribution on R2 and R3
R1 is ONLY in EIGRP 100, and is THE ONLY router you can ping from. R4 has a loopback interface thatmust be pinged from R1.
R4 is running OSPF and has redundant link to EIGRP network over R3 router.
The requirement of this sim is traffic from R1 should go to the most optimal route to reach 172.16.100.0/24network
Notice: You should make a ping from R1 to 172.16.100.1 network to make sure everything is workingcorrectly.
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 2/15
Answer and Explanation:
Thanks to POONAM who send us the topology and configuration. She got 100% on EIGRP-OSPF lab so
this solution is perfect! Please say thank to him and others who contribute this lab-sim!
SOLUTION from POONAM
First we need to find out 5 parameters (Bandwidth, Delay, Reliability, Load, MTU) of the s0/0/0 interface (the
interface of R2 connected to R4) for redistribution :
R2#show interface s0/0/0
Write down these 5 parameters, notice that we have to divide the Delay by 10 because the metric unit is in tensof microsecond. For example, we get Bandwidth=1544 Kbit, Delay=20000 us, Reliability=255, Load=1,
MTU=1500 bytes then we would redistribute as follows:
R2#config terminal
R2(config)# router ospf 1
R2(config-router)# redistribute eigrp 100 metric-type 1 subnets
R2(config-router)#exit
R2(config-router)#router eigrp 100
R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500
(Notice: In fact, these parameters are just used for reference and we can use other parameters with noproblem. Also, a candidate said that the simulator didnt accept the Bandwidth of 1544; in that case, we canuse a lower value, like 128.
If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000)
Note: usec here does not mean microsecond (which is 1/1000 milliseconds) but means millisecond. In shortusec = msec. I dont know why they use the word usec here but just think it is msec (According to thislink: http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094cb7.shtml#eigrpmetrics:
The delay as shown in the show ip eigrp topology or show interface commands is in microseconds)
For R3 we use the show interface fa0/0 to get 5 parameters too
R3#show interface fa0/0
For example we get Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500 bytes
R3#config terminal
R3(config)#router ospf 1
R3(config-router)#redistribute eigrp 100 metric-type 1 subnets
R3(config)#exit
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 3/15
R3(config-router)#router eigrp 100
R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500
Finally you should try to show ip route to see the 172.16.100.1 network (the network behind R4) in the
routing table of R1 and make a ping from R1 to this network.
Note: If the link between R2 and R3 is FastEthernet link, we must put the command below under EIGRP
process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4), which is better than R1 -> R2 ->R4.
R2(config-router)# distance eigrp 90 105
This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP externalroutes to 105, which is smaller than the Administrative Distance of OSPF (110) -> the link between R2 & R3will be preferred to the serial link between R2 & R4.
Maybe the copy running-config startup-config command will not work in this lab so dont worry, just skip it.
Note: Please check the OSPF process numbers first before typing these commands. Maybe they are not ospf1 like above.
If you want to have a closer look at this sim and understand more about the distance eigrp command, pleaseread my OSPF EIGRP Redistribute Lab in GNS3.
Other lab-sims on this site:
EIGRP Stub Sim
OSPF Sim
IPv6 OSPF Virtual Link Sim
EIGRP Simlet
Policy Based Routing Sim
Comments
Comment pages Previous 1 17 18 19 26
1. Jim
June 23rd, 2013
The Fast Ethernet links have more bandwidth than the Serial Links.I guess its more optimal path rather
than shortest path. If it asks for shortest path dont use the distance command.
2. rav
June 25th, 2013
Passed today. Required to pass traffic through shortest path with fastest links. So do exactly as the sim
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 4/15
says.got 100 %
3. shruthi @ banJune 25th, 2013
rav @ so fastest and shartest means shartest means r1-r2-r4 if it is fastehetnet between r2and r3 thattime it is fastest link so which one we configure clear it
4. shankarJune 26th, 2013
Passed on Monday boyi dumps and digtatut labs is more enough Concentrate on SIM its littlebit difficulty I faced , but managed because of hands on experience Understand the LAB and do .. its
very easy Best Of Luck Folks.
5. marcell
June 27th, 2013
does the delay on the fast ethernet interface on router 3 facing router 4 need to be 10 instead of 100?
when I do a show int fa0/1 on router 3 it is showing, delay 100.
so, if we device 100/10=10
please assistant
6. Chris
June 28th, 2013
CAN SOMEONE PLEASE TELL ME WHERE I CAN DOWNLOAD THE LAB FOR CCNPROUTE SIMULATOR QUESTIONS!?!?
7. shankarJuly 1st, 2013
@krish Why want to download ???? Create it .Wanna help contact me
8. SalmanJuly 2nd, 2013
passed today with 941/1000 all labs still valid the eigrp stub lab is slightly different from R3 you have toping R4 from loop back interface . will give more details later.Igor dumps are 100% valid.
9. MikeJuly 4th, 2013
Can someone tell where can I downloads the five labsim
10. fedrostar
July 4th, 2013
Does anyone have the gns3 labs for the five labs pleaseee
11. Ala
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 5/15
July 8th, 2013
do i have to use the distance command to chose the path (R1-R2-R3-R4) ?
PLEASE ADVISE .. Thanks :)
12. Rouslan
July 9th, 2013
Here is gns3 labs http://www.4shared.com/file/MNxMccev/GNS3_642-902_Test_Sims.html
13. husnaJuly 9th, 2013
i want take the ccna exam this september.. who can tell me which website can help me.. please
14. husna
July 9th, 2013
tell me at [email protected]
15. M7July 9th, 2013
hi all
I have passed the exam today with score 950.
all labs here was in my exam .
and question exactly from examcollection.com site in the Igors dump .
16. M7
July 9th, 2013
husna
July 9th, 2013
i want take the ccna exam this september.. who can tell me which website can help me.. please
my strongly recommended to you : no need more than 2 sites
1- 9tut.com
2- last dump of http://www.examcollection.com/ sit
but be sure they are new version of ccna and what last day for old version
17. Anonymous
July 10th, 2013
why is it so hard to find the GNS3 topology for these labs?? Can no one upload them?
18. @ husnaJuly 11th, 2013
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 6/15
send me ur mail i wil send u all stuffs ( dumps + labs ) .. and help
19. Lakmal
July 12th, 2013
If anybody needs 5 labs simulation feel free to contact me ;) [email protected]
20. Anonymous
July 12th, 2013
hi all
passed today, thanks digitaltut.
Got 4/5 of the labs.
MCQ from examcollection.com site in the Igors dump still valid.
21. moldova news
July 13th, 2013
ivzgqO Thanks-a-mundo for the blog article.Much thanks again. Will read on
22. khan
July 14th, 2013
mail me if any one wants the GSN3 lab [email protected]
23. akki
July 15th, 2013
Passed the Route exams. I got following simsOSPF Virtual LinkEigrp redis
Policy route mapipv6 ospfeigrp stub.
All the sims were same with IPs being different and for the EIGRP redis sim the link between R4 & R3was a Serial and all other were Fast ethernet.
24. strength of mindJuly 17th, 2013
hi allpassed today, thanks digitaltut.This Lab is same as in digitaltut no worries
25. Anonymous
July 17th, 2013
Hi everyone,
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 7/15
In the second Sim when I enter router eigrp 100 the result isThe command is not correct!Help will be appreciated.
26. CCNP Labs
July 18th, 2013
Hi all,
Does those 5 labs still valid in the CCNP-Route exam ?
Please help to share im going to take CCNP-Route Exam soon.
Your help much appreciated.
27. Happy T joyJuly 18th, 2013
please is any one having CCNP route exam question , please if you have kindly send the link to my mail
Thanks to you all.
28. khanJuly 18th, 2013
had this lab in my exam today fast ethernet links were between R1>R2 and R2>R3rest was same as here
29. femhab
July 20th, 2013
i tried practicing on just installed GNS3, it was requesting for ios image. pls how do i get away with this
30. AtlantaJuly 21st, 2013
Hello,
I passed (906/1000) CCNP route exam today. I got all questions from PASS4SUSURE. but please putsome concentration on options (In exam they shuffled options). I got total 53 questions including 4 labsSIMs and 2 hours time.
all LAB are valid. but, they are changing IP addresses.
31. [email protected] 24th, 2013
Please ladies and gentle men, I have completed my CCNA and heading for the CCNP. Please help me
with reading materials and dumps. Any of the CCNP: Security, Switching, etc. Please help, please.
My email is [email protected].
Thanks may God Almighty bless you.
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 8/15
32. Anon51214July 24th, 2013
Passed my exam today, scored 1000 marks, thanks you guys.
33. BJuly 26th, 2013
Hi everyone,
How come the first path R1-R2-R4 is (2 serial links) is considered slower than R1-R2-R3-R4 (2 serial
links and a fastethernet link). whether it is ospf or eigrp, the cost for the first path is less. can someoneclarify please.
Second. why is there no route filtering although we have to routers performing redistribution? wouldnt
this create routing loops?
34. BJuly 26th, 2013
ok. i just noticed If the link between R2 and R3 is FastEthernet link so that answers the first question.
As for the second question, since the links are directly connected to the affected routers there will be noloops.
I noticed while doing the lab in GNS 3 that if the link between R2 and R3 is serial and we do the labhere like written above. traffic would be asymmetrical. The path from R1 will be R1-R2-R4 which is the
optimal route, but from R4 it would be R4-R3-R2-R1 since R4 will prefer the Fast Ethernet link and thiswont be the optimal route. what are your views?
35. Daniel
July 27th, 2013
This lab on my test today.Connection between R2 & R3 is FastEthernet. Must use this command.
R2(config-router)# distance eigrp 90 105
36. GhorbaJuly 28th, 2013
Passed yesterday with 965/1000labs are the same as digitaltut.
and this lab I found that the link between R2 and R3 is fastethernet so I used the command R2(config-router)# distance eigrp 90 105 under eigrpGood Luck for allThankd digitaltut
37. MoidinJuly 28th, 2013
Hello Guys,
EIGRP Metric(K-Value) is need configure as same number?
or we can configure Different Numbers..!!
38. CCNP Student
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 9/15
July 30th, 2013
Can anybody let us know that whether exam allow you to use ? and TAB in labs ? Thanks. Your helpwill be much appreciated.
39. DanJuly 30th, 2013
If you have GNS3 installed, why and what is that hard to create those sims lab ? remember all of youpassing CCNP meant you know how to configure Right ???What is hard on this Redistribution Sim? you have only 4 routes to configure also
this site is to share issues not to ask for dump and sim file.
40. SaidJuly 30th, 2013
Its necessary to put metric type to 1 when redistubuted in ospf ?
41. Consula
July 31st, 2013
Pass today 958.Labs Valid.
Many thankx to Digitut !!!!
42. dinesh
August 3rd, 2013
passed today 930still valid..
thanks digitaltut.
43. ZTEWTAugust 4th, 2013
Still valid.
R2 -> R3 was FastEthernet for me.
Better to setup in GNS3 and practice several times before you go.
44. PaulAugust 4th, 2013
can someone tell me by email what lab are in the exam for Routing? [email protected]
45. KHNAugust 6th, 2013
Assuming that R2 > R3 is Fastethernet , this means R1 has to choose between R1>R2>R4 (two seriallinks ) OR R1>R2>R3>R4 (one serial link and two Fastethernet ) if you want R1 choosing the path
R1>R2>R3>R4 then what K-values (those 5 parameters) you use when redistributing OSPF intoEIGRP do not matter, WHY?
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 10/15
Because R1 has only way out and it is R2, the path decision has to be made by R2, why R2 chooses theserial interface in first place is because R2 will know the path to 172.16.100.0/24 from R4 as an O IA(OSPF inter area route) and from R3 as an D EX (External EIGRP route). So R2 will choose the serial
link between R2&R4 not because of any metric or k-values but because of the Administrative distanceof OSPF (110) being lower than the administrative distance of External EIGRP router which is 170, theroute with lowest administrative distance will be preferred no matter of metric. Manipulating the default
administrative distance , distance eigrp 90 105 ,of external EIGRP (from 170 to 105) routes and makingthem lower than that of OSPF (110) will make R2 to choose the path R2>R3>R4 ,
46. DeepaReddy
August 8th, 2013
@ALLThis is the easiest lab to set up in GNS3 so far
47. DeepaReddy
August 8th, 2013
@ALL
We can manipulate the path using ACL and route maps but they are not allowed in the exam
48. DeepaReddyAugust 8th, 2013
@ALL
If they say shortest path then no need to use distance commandIf they say optimal path then you need to use distance command to manipulate the route
49. atyu
August 8th, 2013
B have right,
When we have serial link between R2 R3 we will send icmp request to R2, R2 will choose R4because this route has better AD an R4 will send it toward.
ButWhen we receive reply from 172. network on R4, R4 will use route to R1 loopback with bettermetric so:
- with metric-type 2 and defualt metric reply will load balance between R4-R2-R1 or R4-R3-R2-R1- with metric-type 1 and default metric when we receive LSA on R4 we will add cost of link where wereceive this link so network from R3 will add lower cost then LSA from R2 (because FA is better link)
so reply will choose R4-R3-R2-R1 and it is not optimal path for reply in this situation.
50. alphaAugust 11th, 2013
Lab still valid.
51. +++++++++++ hjhg +++++++++++++++++August 12th, 2013
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 11/15
ii have cleared the exam .the dumps available in this site http://ruturl.com/tja
52. Don Know
August 12th, 2013
Under Router OSPF 1, in the command redistribute eigrp 100 metric-type 1 subnets, why do we needmetric-type 1?Couldnt we just put redistribute eigrp 100 subnets?
53. Don KnowAugust 12th, 2013
Also, when we enter the metrics for redistribution on R3, why is the Bandwidth of 10000 not divided by10 and entered as 1000?
54. Don KnowAugust 12th, 2013
Cancel that last question, I was looking at the wrong numbers.
But I still need to know why we should use metric-type 1 ?
55. fatalistAugust 13th, 2013
Passed today with 965 score. They were a few changes in this lab. R1-R2-R3 link was fastethernet and
you need to do distance 90 100 on R2 to pass traffic using shortest path and highest bandwidth link aswas written in description. Need at last to do ping and telnet but telnet not working. I did only ping.
56. AnonTester
August 13th, 2013
When redistributing eigrp into ospf why are we adding metric-type 1 when the default is metric-type
2? Do the directions state to change it to a metric-type 1?
57. AnonTester
August 13th, 2013
Just took test today and passed, metric-type doesnt matter. It doesnt request which metric-type to use.So whatever one you want to use, it doesnt matter as long as you redistribute properly.
58. CERO
August 14th, 2013
info is incompleted. In what area would us configurated the Loopback interface?
59. NKANZE Zack
August 14th, 2013
Dump and lab still valid.
completed exam today 906/1000. But you cant use cop run start in some lab
60. AnonTester
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 12/15
August 14th, 2013
@ceroYoure not configuring a loopback interface, directions dont state to configure one. READ the
instructions.
61. AnonymousAugust 14th, 2013
I Pass today, the sims are 100% valid. Obs: I change the original distance, but It appeared like - - in
show ip prot. before the change, it was 90 170
62. THANG
August 15th, 2013
This lab in my exam hours ago
63. KP
August 15th, 2013
i think ospf process should be 24 on r3 and 34 on r4 as below..comments pls?
R3(config)#router ospf 23
R2(config-router)#redistribute ospf 24 metric 1544 2000 255 1 1500
R3(config)#router ospf 34
R3(config-router)#redistribute ospf 34 metric 10000 100 255 1 1500
64. Don Know
August 15th, 2013
@KP
Im no expert, but the command is used to redistribute the entire OSPF process on a router, not just a
single OSPF area.
The numbers 24 and 34 identify the areas not the OSPF process ID.
65. Don Know
August 15th, 2013
You will need to check the running config (sh run) to get the OSPF process ID.
66. Anonymous
August 16th, 2013
will do it next week
Comment pages
Previous 1 17 18 19 26
1. No trackbacks yet.
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 13/15
Add a Comment
Name
Submit Comment
Subscribe to comments feed
BGP next-hop-self, community no-export & send-community GNS3 Lab Policy Based Routing Sim
Premium Membership
Become a member to interact with all questions and practice labs!
Find out more or Sign In
ROUTE 642-902
LabSimDrag and Drop Questions
Drag and Drop 2
OSPF HotspotEIGRP Questions
EIGRP Questions 2
EIGRP Questions 3EIGRP Questions 4
EIGRP Questions 5
EIGRP SimletOSPF Questions
OSPF Questions 2
OSPF Questions 3OSPF Questions 4
OSPF Questions 5
OSPF Questions 6OSPF Questions 7
BGP Questions
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 14/15
BGP Questions 2BGP Questions 3
BGP Questions 4
BGP Questions 5Redistribute Questions
Redistribute Questions 2
Redistribute Questions 3Policy Based Routing Questions
IPv6 Questions
IPv6 Questions 2IPv6 Questions 3
Operations Questions
ROUTE FAQs & TipsShare your ROUTE Experience
Practice Labs with GNS3
Basic Labs
Network Resources
CCNA Website
ROUTE Website
SWITCH Website
TSHOOT Website
CCNA Voice Website
CCNA Security Website
CCIP Website
CCDA Website
CCIE Website
Support Digitaltut
Your contribution will help keep this site updated!
Top
Copyright 2010-2013 ROUTE 642-902 Training
-
8/16/13 ROUTE 642-902 Training EIGRP OSPF Redistribution Sim
www.digitaltut.com/route-eigrp-ospf-redistribution-sim#more-26 15/15
Privacy Policy. Valid XHTML 1.1 and CSS 3.BH