RESOURCE GUIDE
®
P r o d u c t M a n u a l
The information contained in this Resource Guide along with additional maintenance and repair information, videos and photos can be found online at www.STARTinternational.com
© START International
START International warrants all parts on ZCM series tape dispensers against defects in design, materials and workmanship for a period of 180 days. Parts excluded from this are: cutting blades, silicone rollers and cutter liners; these parts are considered “wear parts”. Labor to replace defective parts will be performed at no charge for the first 90 days after date of purchase. Warranty does not cover transportation costs.
START International’s sole obligation under this warranty is limited to repair, replacement or credit of the purchase price, at our option, which do not properly perform the function for which they were designed.
Warranty repair is contingent upon START’s examination and determination that alleged defects have not been caused by misuse, abuse, improper installation or application, repair, alteration, accident or neglect in use, storage, transportation or handling.
The above warranty and remedy constitutes START International’s sole liability hereunder and are in lieu and exclusive of all other warranties and remedies expressed, implied, or statutory, including, but not limited to, those of merchantability and fitness for a particular purpose.
REPAIR POLICYContact START INTERNATIONAL to determine nature of problem.
Furnish START with the following information:1. Who the unit was purchased from.2. Model number and serial number.3. Date purchased (copy of invoice or packing slip required).
START will issue an RMA (Return Material Authorization) for the repair. Return machine to START by freight, insured and prepaid. START will notify the customer if there is a repair charge.A $25.00 evaluation charge will apply to all non-warranty repairs, which will be applied to repair change.
For the full Warranty & Repair policy please visit www.STARTinternational.com
2
Read this resource guide before operating to ensure proper operation. Keep this resource guide on hand for future reference.
Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description of Parts and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-6 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Additional Information for ZCM2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Exploded Views/Parts Breakdown. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-14 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15-23
CONTENTS
WARRANTY POLICY FOR zCm SERIES TAPE dISPENSERS
3
• If using automatic feed, when one piece of tape is removed the unit will automatically feed and cut the next piece at the preset length.
• The tape length is easily seen on the LED display, and operation is simple — press the CM key or MM key to set the length (Setting limit: 20mm to 999mm).
• If a piece of long tape is needed, press ADVANCE key for desired length, then press CUT key to cut.
• The blade unit can be removed and replaced easily. (Tape jamming is also easily fixed by removing the blade unit.)
FEATURES
NOTES
Do not use volatile liquids (thinner, benzine, etc.) to clean the dispenser. Wipe with dry cloth only.
Do not use the tape dispenser in humid or dusty places.
do not insert your fingers into the cutting head!
Do not leave the tape dispenser in direct sunlight.
Do not drop the tape dispenser or subject it to heavy shocks.
Do not insert bars or plates into the tape outlet – this will damage the blade.
© START International
4
dESCRIPTION OF PARTS ANd FUNCTIONS
SEPARATINg Roller
FUSE
FEEd Roller
• POWER Switch Press to turn power ON or OFF.
TAPE LENgTh • TAPE LENgTh display The last digit indicates millimeters and the first two digits centimeters.
• LENgTh AdJUSTmENT Keys Press mm key to set tape length in mm. Press cm key to set tape length in cm.
• AdVANCE / CUT Key Feeds tape to the preset length and cuts automatically.
ADVANCE / CUT
• PRESSURE Knob Adjusts top roller to change pressure on tape.
• REVERSE Key Feed Roller reverses. Use this key to change tape.
• CUT Key Press to cut tape.
POWER Switch
• RESET Key Length display is reset to 20mm. This key can be used as an emergency stop.
• AdVANCE Key Tape dispenses as long as key is pressed.
REVERSE Key
TAPE LENgTh display
RESET Key
AdVANCE Key
SENSOR Plug
PRESSURE Knob
CUTTERLatch
REEL
LENgTh AdJUSTmENT Keys
AUTO SENSOR Switch
AdVANCE / CUT Key
CUT Key
5
Using Automatic Feed:
1. Plug in power cord and turn unit on.
2. Set tape on the center of reel and stick the end of the tape onto the metal feed roller. Press ADVANCE key until tape feeds through cutting unit. If the tape will not feed through the cutter, fold corners of the tape to form a triangle shape and re-feed (Fig. A).
3. Press CUT key to cut tape.
4. Set the tape length. Press MM key to set length of 0-9mm. Press CM key to set length of 20-990 mm.
5. Set PRESSURE knob • If tape curls or slips, increase pressure. • If tape creases, decrease pressure.
6. Turn sensor switch ON. Tape will be fed to set length and cut. When the piece of tape is removed from machine, another piece will be fed and cut. (Turn sensor switch OFF when not in use.)
Using AdVANCE / CUT keyWith AUTO SENSOR switch OFF, press ADVANCE / CUT key. Tape will be fed to set length and cut.
Using AdVANCE keyPress ADVANCE key until desired tape length has been fed. (This key overrides the preset length.) Press CUT to cut tape.
Changing tapePress the REVERSE key. The feed roller will rewind the tape away from cutter area. Remove the tape manually.
In case of tape jamPress REVERSE key to remove tape from cutter area. Rewind and replace tape on roller. Also, remove cutter unit to verify no tape is stuck on roller or cutter.
OPERATION
FIG. A
FOLDTAPE BACK
© START International
6
To Replace Cutter UnitTurn off auto sensor and power before removing cutter unit. Pull sensor plug out, then pull cutter unit forward while pressing the knob on the top of the unit (Fig. 1).
To replace blades, remove the two screws inside head. Blade can then be lifted out and replaced. Before remounting the cutter unit to the frame, the lower blade must be bottomed out. If it is not completely down, use a screwdriver to lower it (Fig. 2).
Remount the cutter unit by aligning the bottom of the unit then pushing in the top.
Replacing the Separating RollerTurn off the sensor and power before removing the separating roller. Remove the cutter unit, then remove the two screws (Fig. 3).
To remove roller holder, grip rubber ring in the center of separating roller and pull. Then remove the screws on the left and right of the roller holder and pull off shaft and gear (Fig. 4).
KNOB
LOWER BLAdE
ROLLER hOLdER
ShAFT
FIg. 4
FIg. 3
FIg. 2
FIg. 1
OPERATION (CONT'd)
PRECAUTIONS
• Set the tape properly as described in these instructions. (If the end of the tape is folded when the tape is set, the tape may jam at the tape outlet.)
• This machine will cut virtually any type of pressure sensitive tape (aluminum, filament, etc.). If tape is thicker than .05" or thinner than .03”, test for compatibility.
• Because of tape differences (elasticity, stickiness, etc.), some tapes may not cut at the set length. If this occurs, adjust the set length accordingly.
• If tape sticks to the blade, remove the cutter unit, clean with alcohol and apply silicone oil to the blade.
• To reduce jamming, remove tape from machine when not in use.
gEAR
When problems occur, carry out the following procedures. If the tape dispenser does not operate normally after following the troubleshooting procedures, contact your supplier.
1. If the motor does not drive: • Check that the power cord is plugged in. • Check that the power switch is turned on.
2. If the tape does not cut: • Make sure the cutter unit is set properly and clean.
3. If the LED does not light: • Check that the power cord is plugged in. • Check that the power switch is turned on.
4. If the tape does not advance: • Check if the tape is jammed at the roller or in the cutter unit. • Check that the tape is set properly.
5. If the auto sensor does not work: • Check that the sensor plug is plugged in. • Check that the sensor switch of cutter unit is on. • Check that the sensor part of the cutter unit is not stained.
6. If the tape advancing does not stop: • Check that the tape is centered. If not, set the tape at the center of the feed roller so that the sensor will see the tape.
7
TROUBLEShOOTINg
SPECIFICATIONS
© START International
model zcM1000 zcM2000
display 3-Digit LED
Applicable Tape Width .28” - 2” (7 - 50mm)
Core diameter 3” (optional 1”, 1.25”, 1.5”)
Tape Length Set Limit .79” - 39” (20-999mm) ± .040”
memory Settings 1 3
drive DC Motor for Tape Advancement and Tape Cut
Power Consumption 18W
Power (AC) 117V 50/60Hz or 230V 50/60Hz
Ambient Temperature 41º - 104ºF (5º - 40ºC)
Ambient humidity Less than 80% RH
dimensions 5.4 x 8.6 x 6” (14 x 22 x 15cm)
Weight 5.3 lbs (2.4 kg)
mEmORY KeyThe reverse key on the ZCM1000 is changed to the MEMORY (M) key on the ZCM2000. (The reverse function can be accessed by pressing the FEED key and the M key at the same time. This function is for changing tape.)
Setting memories1. Press and hold the M key until the LED display flashes.
2. Using the cm and mm keys, set the desired length for first cut. A. The mm key controls the millimeter setting (1 digit). B. The cm key controls the centimeter setting (2 digits). (Ex: 125mm = 12cm and 5mm.) C. Press M key to record memory. (The display will then flash “999”.)
3. Set additional lengths as shown in #2. (If only two lengths are needed, record “999” as last length — “999” length will not be memorized.)
4. After lengths are set, the display will flash “0”. Press mm key to switch between “0” and “5”:
• On “0”, the machine will feed and cut the first set length until the M key is pressed, then it will feed the second length until the M key is pressed, and so on.
• On “5”, the machine will feed and cut the recorded lengths in series.
5. When set correctly, press and hold the M key until the display stops flashing. The first preset length will be shown on the display and the unit is ready to use.
6. Programmed tape lengths will be fed and cut in order when using either the sensor unit automatic feed and cut or the ADVANCE / CUT button.
7. If RESET (20) key is pressed, all of the memory will be erased.
8
AddITIONAL INFORmATION FOR zCm2000
WEEKLY - Remove cutting head. Clean and look for missing roller rings. Replace as needed.
MONTHLY- Remove blade spring and blades to inspect cutter liners. Place one drop of silicone oil on each liner, or replace if worn. Inspect feed roller and blades for tape fragments or adhesive buildup. Clean with alcohol.
PREVENTIVE mAINTENANCE
9
ExPLOdEd VIEWS / PARTS BREAKdOWN
ChANgE ThE SEPARATINg ROLLER
REmOVE BOdY COVER ANd BOTTOm PLATE
550-1
550S
560-1
200-1
© START International
Numbers in balloons represent the last digits in replacement part number. When ordering, ask for ZCM1000P _ _ _
100
10
ExPLOdEd VIEWS / PARTS BREAKdOWN
FRONT hOLdER STRUCTURE
FRONT HOLDER 3 UNIT
Numbers in balloons represent the last digits in replacement part number. When ordering, ask for ZCM1000P _ _ _
100
11
ExPLOdEd VIEWS / PARTS BREAKdOWN
FEEd STRUCTURE
REmOVINg SENSOR UNIT
560-1
Bearing-2
© START International
Numbers in balloons represent the last digits in replacement part number. When ordering, ask for ZCM1000P _ _ _
100
B
PP
S
PP
S
S
NOTE: Parts grouped within broken lines can be purchased as complete assemblies.
12
ExPLOdEd VIEWS / PARTS BREAKdOWN
Numbers in balloons represent the last digits in replacement part number. When ordering, ask for ZCM1000P _ _ _
100
B
PP
S
PP
S
S
NOTE: Parts grouped within broken lines can be purchased as complete assemblies.
13
ExPLOdEd VIEWS / PARTS BREAKdOWN
Corresponding Parts:ZCM1000 ZCM2000 102 ................ 605 251 ................ 612 504 ................ 601
The information contained in this Resource Guide along with additional maintenance and repair information, videos and photos can be found online at www.STARTinternational.com
© START International
14
117V
230V
230V
ExPLOdEd VIEWS / PARTS BREAKdOWN
BOTTOm PLATE WIRINg
CONTROL PANEL CONNECTIONS
Numbers in balloons represent the last digits in replacement part number. When ordering, ask for ZCM1000P _ _ _
100
15 © START International
Part # Part Name Illustration Notes
zcM1000P101 Body cover Standard Part
zcM1000P102 Panel cover Standard Part
zcM1000P105 LED cover Standard Part
zcM1000P106 Pressure Knob Standard Part
zcM1000P107B Core holder Standard Part
zcM1000P111 Transformer117V
Standard Part(on 117 Volt Machines)
zcM1000P112 Transformer230V(CE)
Standard Part(on 230 Volt Machines)
zcM1000P113 Screw (4* 8)Standard Part
(To hold transformeron base)
zcM1000P114 Nut with washer Standard Part (4mm)
zcM1000P115 Base Standard Part
zcM1000P116 Rubber feet Standard Part
16
Part # Part Name Illustration Notes
zcM1000P118 Power switch Standard Part
zcM1000P120 Fuse (1A) Standard Part
zcM1000P121 Fuse holder Standard Part
zcM1000P124 Center frame Standard Part
zcM1000P136 Separating roller unit
Standard Part(Used with P138)
zcM1000P138 Separating roller ring Standard Part
zcM1000P141 Roller shaft Standard Part
zcM1000P142 Screw (3*20) Standard Part(To Mount to P136)
zcM1000P146 Bearing Standard Part
zcM1000P150 Screw (3*25) Standard Part(To Mount feed roller)
zcM1000P154PP5 Pressure roller 5TStandard Part
(5 teeth for less pressure)
zcM1000P155 Pressure roller collar Standard Part
17
Part # Part Name Illustration Notes
zcM1000P161 Cutter holder spring Standard Part
zcM1000P164 Pressure roller spring Standard Part
zcM1000P178 Earth spring Standard Part
zcM1000P182 Flat revet Standard Part
zcM1000P187Cutter motor
(Yellow & Blue line)
Standard Part
zcM1000P200-1 Connector 4(3 pins) Standard Part
zcM1000P204 Pinion gear Standard Part
zcM1000P206S Power cord(For 117V)
Standard Part(USA, Plug type B)
zcM1000P206-2 Power cord(For 230V)
Standard Part(German/EU, Plug type
F)
zcM1000P215 Sensor unit cover Standard Part
zcM1000P228 Screw (3*8) Standard Part(To mount front holder)
zcM1000P229 Screw (3*14)Standard Part
(To mount control panel)
© START International
18
Part # Part Name Illustration Notes
zcM1000P230 Screw (2.6*3)Standard Part
(To mount motor, Gold color)
zcM1000P231 Screw (3*10A)Standard Part
(To mount cutter gear cover)
zcM1000P232 Screw (3*5) Standard Part(To mount cutter spring)
zcM1000P233 Screw (3*8) Standard Part(To mount body)
zcM1000P234 Screw (3*8) Standard Part(To ground earth)
zcM1000P237 Screw (4*6) Standard Part(To mount gear unit)
zcM1000P245 Advance / Cut button Standard Part
zcM1000P246 "cm" Button Standard Part
zcM1000P247 "mm" Button Standard Part
zcM1000P248 "Cut" Button Standard Part
zcM1000P249 "Advance" Button Standard Part
zcM1000P250 "20" Buttonreset Standard Part
19
Part # Part Name Illustration Notes
zcM1000P251 "Reverse" Button Standard Part
Standard Part(Special coated blades)
Standard Part(Special coated blades)
zcM1000P256 Top Blade Holder Standard Part
zcM1000P257PP Blade springwith comb Standard Part
zcM1000P258 Blade liner (Right) Standard Part
zcM1000P259 Blade liner (Left) Standard Part
zcM1000P289 Silicone oil Included with all models
zcM1000P312 Feed roller 2 Standard Part
zcM1000P403 Flat gear 15 Standard Part
zcM1000P404 Flat gear 16 Standard Part
zcM1000P406 Flat gear shaft 14 Standard Part
zcM1000P254/5 Blade set(Upper & Lower)
© START International
20
Part # Part Name Illustration Notes
zcM1000P407 Flat gear shaft 13 Standard Part
zcM1000P408 Collar 2 Standard Part
zcM1000P418 Gear unit Standard Part
zcM1000P421 Flat Gear 11 Standard Part
zcM1000P422 Flat Gear 12 Standard Part
zcM1000P423 Flat Gear 13 Standard Part
zcM1000P424 Flat Gear 14 Standard Part
zcM1000P427 Feed roller gear 3 Standard Part
zcM1000P428 Screw (4*8) Standard Part(to mount gear cover)
zcM1000P430 Separating roller gear Standard Part
zcM1000P431 Cutter gear 2 unit Standard Part
zcM1000P433 Cutter part gear cover 2 unit Standard Part
21
Part # Part Name Illustration Notes
zcM1000P435Feed motor
(Red & Brown line)
Standard Part
zcM1000P501 Side frame(Left) Standard Part
zcM1000P502 Side frame(Right) Standard Part
zcM1000P503 Separating roller holder Standard Part
zcM1000P504 PCB Standard Part
zcM1000P507S Cutter holderStandard Part
(Plastic Frame Only with Front Holes)
zcM1000P508S Cutter holder unit 2
Standard Part(Plastic frame + blades
with front holes)
zcM1000P517 Roller pressure unit 2 Standard Part
zcM1000P518 Front holder unit 3 Standard Part(frame + motor)
zcM1000P519 Front holder 3 Standard Part(Plastic frame only)
zcM1000P520 Cut lever press 2 Standard Part
zcM1000P521 Cut lever liner 2 Standard Part
© START International
22
Part # Part Name Illustration Notes
zcM1000P522 Cut lever collar Standard Part
zcM1000P523 Cut lever unit 2 Standard Part
zcM1000P524 Open spring Standard Part
zcM1000P525 Open knob Standard Part
zcM1000P526 Open set Standard Part
zcM1000P528 Pinion gear unit 2 Standard Part
zcM1000P533 Separating roller holder unit
Standard Part(with P138 roller rings)
zcM1000P550S Auto feed cutter unit
Standard Part(with 3 flat pin
connector) Complete Cutting Head
zcM1000P555 Sensor cover (Plastic frame only)
zcM1000P560-1 Sensor unit
Standard Part(with 3 flat pin
connector, frame + sensor)
zcM1000P680 Safety guard(With 4 screws)
Standard Accessory for 117V, Installed on 230V machines (Need P507-
S)
zcM1000P901/901a Stopper Standard Part(to secure cutting head)
23
Part # Part Name Illustration Notes
ZCM2000P601 Main Board Unit 2 Standard Part(for zcM2000)
ZCM2000P605 Panel Cover Standard Part(for zcM2000)
ZCM2000P612 Switch Button 3 (memory)
Standard Part(for zcM2000)
Please refer to STARTinternational.com for details on modifications.
zcM1000PB B-kitComplete Parts kit to
convert to "B" modification
zcM1000PNM NM-kitComplete Parts kit to
convert to "NM" modification
zcM1000P504-S D-kitComplete Parts kit to
convert to "D" modification
zcM1000P533-1 T-kitComplete Parts kit to
convert to "T" modification
zcM1000P550M C-kit Part to convert to "C" modification
zcM1000P154 C-kit Part to convert to "C" modification
zcM1000P550E E-kit Part to convert to "E" modification
zcM1000P107D E-kit Part to convert to "E" modification
zcM1000PCR K-kitComplete Parts kit to
convert to "K" modification
Modification KITS / PARTS
BKIT
NMKIT
DKIT
TKIT
CKIT
CKIT
EKIT
KKIT
EKIT
© START International
START International
4270 Airborn Dr. Addison, TX 75001, USA
Tel 972.248.1999 Fax 972.248.1991
www.STARTinternational.com
®
09/08