Download - Replaces Series T - Bosch Rexroth
External Gear Pumps
Series T
AZPT-...
Fixed pumpsV = 20...36 cm3/rev
RE 10 092/02.12
Replaces
RE 10 092/02.07
Overview of contents
Contents Page
General 2
Product overview 3
Ordering code single pumps 4
Ordering code multiple pumps 5
Drive shaft 6
Front cover 6
Line ports 7
Gear pumps with integral valves 8
Design calculations for pumps 8
Performance charts 9
Noise charts 11
Specifications 12
Drive arrangements 13
Multiple gear pumps 15
Dimensions 16
Fittings 18
Service parts 19
Notes for commissioning 20
Fittings 21
Ordering-No. 22
Features
– Nominal pressure 280 bar
– Slide bearings for heavy duty applications
– Drive shafts to ISO or SAE
– Combination of several pumps possible
– Line ports:
connection flange or screw thread
– Optimized pressure pulsation with reduced noise emissions
and vibration excitation in the system
– Consistent high quality
– Considerably longer service life due to reinforced shaft and
case
2/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
GeneralThe key task of external gear units is to convert mechanical
energy (torque and rotational speed) into hydraulic energy
(flow and pressure). In external gear motors this is the other
way round. These machines are required to be highly efficient
in order to avoid unnecessary heat. This efficiency is achieved
by means of precision production engineering and pressure-
sensitive gap sealing.
Moreover, in the low-noise SILENCE pumps, the dual-flank
principle helps to reduce flow pulsation by up to 75 %.
The displacement method
Intake side
Line of actionof rear flank
Front flankdelivery
Rear flankdelivery
Deliv
ery
Q
Time t
Delivery side
Line of actionof front flank
SILENCE gearing
Mean value Qm
Time t
Pulsation
Intake sideDelivery side
Hydraulic line
of action
Metering notches
Hydraulic meshing
Deliv
ery
Q
Standard gearing
The geometry of the displacement gearing, matched in form
by the rotation of the drive shaft, results in the parabolic flow
characteristic shown here on the left. In a standard pump, this
characteristic is repeated each time a gear tooth meshes. With
their dual-flank system, the flow pulsation of SILENCE pumps
is reduced by 75 % – with correspondingly lower excitation of
downstream system components – at double the fundamental
frequency. During this process, the gear pair exhibits an ex-
tremely reduced rear flank backlash, so that hydraulic sealing
is provided not just by the front flank of the driven gear, but
also by the rear flanks. In this way, the front and rear flanks
alternately contribute to flow displacement. And by adapting
the shape of the metering notches, the expansion of the
hydraulic line of action is half that of the standard pump. 1 Retaining ring
2 Shaft seal ring
3 Front cover
4 Slide bearing
5 Centering pin
6 Gear
7 Gear (frictional)
8 Case seal
9 Pump case
10 Bearing
11 Axial zone seal
12 Support
13 End cover
14 Fixing screws
1 2 3 4 5 6 7 8 9 10 11 12 13 14
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 3/22
Overview of “Series T” standard types
Version Page
16
Version Page
17
Cover
Axial seal Radial seal External pressure zone
Flange Compensation forces
Sealing zone
Internal pressure zone
Construction
The external gear pump consists essentially of a pair of gears
supported in bearing bushings or bearing, dependent on the
series, and the case with a front and a rear cover. The drive
shaft protrudes from the front cover where it is sealed by the
shaft seal ring. The bearing forces are absorbed by special
bearing bushings with sufficient elasticity to produce surface
contact instead of line contact. They also ensure excellent
resistance to galling – especially at low speed. The gears have
12 teeth. This keeps both flow pulsation and noise emission
to a minimum.
Gear pump axial compensation
The internal sealing is achieved by forces which are propor-
tional to delivery pressure. This ensures optimum efficiency. The
bearings provide the seal at the ends of the gaps between the
teeth which carry the pressurized oil. The sealing zone between
the gear teeth and the bearings is controlled by the admission
of operating pressure to the rear of the bearing bushings.
Special seals form the boundary of the zone. The radial
clearance at the tips of the gear teeth is sealed by internal
forces pushing them against the case.
4/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
AZ P T – x x – 020 R C B 20 M B 18009 S xxxx
Ordering code External gear units Single pumps “SILENCE”
Function
P = Pump
Series
2 = Case width 110 mm
Version
2 = Chromatized, pinned
Size T
020 = 20.0 cm3/rev
022 = 22.5 cm3/rev
025 = 25.0 cm3/rev
028 = 28.0 cm3/rev
032 = 32.0 cm3/rev
036 = 36.0 cm3/rev
Direction of rotation
R = Clockwise
L = Counter-clockwise
Special
design
Valve adjustment
200 xx = PRV 200 bar
xxx 11 = FCV 11 l/min
18009 = PRV + FCV
180 bar, 9 l/min
Rear cover
B = Standard
E = FCV residual flow
external
S = FCV residual flow
internal
V = PRV + FCV
Seals
M = NBR
K = NBR, SSR in FKM
Drive shafts Front cover Line ports
Suitable front cover
CTapered key shaft
1 : 5B B
Square flange
Centering Ø 100 mm07
Square flange SAE
Thread, metric
N Dihedral claw M C SAE J 744 101-2 B
2-bolt flange
Ø 101.6 mm20 Rectangular flange
DSplined shaft SAE
J 744 22-4 13TC M
2-bolt mounting
Centering Ø 52 mm
with seal ring
PSplined shaft SAE
J 744 19-4 11TC
Not all variants can be selected by using ordering code!
Please select the required pump by using the selection tables (standard types) or after consultation with Bosch Rexroth!
Special options are possible upon request.
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 5/22
AZ P TTSS – x x – 032/022/016/005 R C B 20 20 20 20 K B
Ordering code External gear units Multiple pumps “SILENCE”
Function
P = Pump
Series
B = 1.0...7.1 cm3/rev
S = 4.0...28 cm3/rev
F = 4.0...28 cm3/rev
T = 20.0...36 cm3/rev
N = 20.0...36 cm3/rev
U = 22.5...63 cm3/rev
G = 22.5...63 cm3/rev
Series, relates to pump
section 1
2 = Case width 110 mm
Version, relates to pump
section 1
2 = Chromatized, pinned
Size
corresponding to each series
Direction of rotation
R = Clockwise
L = Counter-clockwise
Rear cover
relates to last pump section
B = Standard
Seals
M = NBR
K = NBR, SSR in FKM
Shaft seal relate to pump
section 1
Drive shafts relates to pump part 1
Front cover relates to pump part 1
Line ports every pump parts
Series B: Suitable front cover
HTapered key shaft 1 : 8 O O
Square flangeCentering Ø 25.38 mm 02
Thread, metricDIN 3852 T1
Series F, S:
CTapered key shaft 1 : 5 B B
Square flangeCentering Ø 80 mm 20 Rectangular flange
HTapered key shaft 1 : 8 O O
Square flangeCentering Ø 36.47 mm
RSplined shaft SAE J 744 16-4 9T R R
SAE J 744 82-2 A Centering Ø 82.55 mm2-bolt mounting
Series N, T:
CTapered key shaft 1 : 5 B B
Square flangeCentering Ø 100 mm 07
Square flange SAEThread, metric
DSplined shaft SAE J 744 22-4 13T C C
SAE J 744 101-2 B Centering Ø 101.6 mm2-bolt mounting
20 Rectangular flange
N Dihedral claw M M Centering Ø 52 mm with seal ring
Series G, U:
CTapered key shaft 1 : 5 B B
Square flangeCentering Ø 105 mm 07
Square flange SAEThread, metric
DSplined shaft SAE J 744 22-4 13T C C
SAE J 744 101-2 B Centering Ø 101.6 mm2-bolt mounting
20 Rectangular flange
HTapered key shaft 1 : 8 O O
Square flangeCentering Ø 50.78 mm
Not all variants can be selected by using ordering code!
Please select the required pump by using the selection tables (standard types) or after consultation with Bosch Rexroth!
Special options are possible upon request.
6/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Drive shafts
9±0.2
45.5±0.6
20
Ø2
21:5
54
2'3
8"
1'
M14x1.5-m-06
4x6.5 DIN 6888
DIN 128-A14-FSt
2
9.5±0.1
Min. 20.1usable shaft
length
ANSI B 92.113T 16/32 DP30° pressure angle
31
Ø2
2–
0.0
72
Ø2
2–
0.0
20
Ø2
1.8
06
–0
.12
7
8.8±0.3
Ø2
1.8
±0.0
84
2.7±0.5
Pump without shaft seal
–0
.08
38
–0
.02
5
9.5±0.1
41±0.4
Min. 23 usable shaft length
Ø2
1.8
06
–0
.12
7
Ø2
2–
0.1
Splined shaft SAE J 744 19-4 11T
N
D P
Front cover
B C
55±1
.5
153±1
.5
132±0
.2
9±0.2
12.5±1.5
Ø22
±0.518
.75±1
44.2
±0.1
88.4±0.2
110±1.5
11±0.135
R 10
±0.5
Ø10
0 –0.
054
9.5±0.1
13.2±1
12.5±0.1
42
±2
R 6
0±1
.1
174±1.3
146±0.15
14.3+0.27SAE - B"X"
"X"
max. 3
Ø2
4
Ø1
01
.6–
0.0
5
Ø5
1
C
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 7/22
Front cover (continued)
33±0.1
2xM10 – 10.9Pump without shaft seal
3.2±0.2
2±0.2
11.5±0.2
7.2±0.2
66
±0.2
Ø4
0±0
.18 1
4±0
.1
25
±1.5m
in. 1
0.6
66±0.2
–0
.07
6Ø
52
–0
.03
0
Ø4
7.8
–0
.2
Line ports
07 Square flange SAE, thread, metric
D
C
F
E
Ordering Size Pressure side Suction side
code C D E F C D E F
07 20 cm3 18 47.6 M 10
depth 14
22.2 25 47.6 M 10
depth 14
22.2
22.5...36 cm3 52.4 26.2
20 Rectangular flange
D
C E
45° 45°
Ordering Size Pressure side Suction side
code C D E C D E
20 20...36 cm3 18 55 M 8
depth 13
26 55 M 8
depth 13
M
8/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Gear pumps with integral
valvesIn order to reduce external pipework it is possible to incorpo-
rate a flow-control valve or pressure-relief valve in the rear cover
of the gear pump. A typical application of this is in the supply
of hydraulic oil in power steering systems. The pump delivers a
constant flow irrespective of the speed at which it is driven. The
excess flow is either returned internally to the suction port or
distributed externally to other items of equipment.
Qconst. Qconst.Qconst.
p1
p1
3-way flow-control valve.
Excess flow returned to suction
line
Qconst.
= 2...30 l/min
3-way flow-control valve.
Excess flow distributed externally;
loadable
Qconst.
= 2...30 l/min
3-way flow-control valve with
pressure-relief valve.
Excess flow returned to suction
line
Qconst.
= 2...30 l/min
p1 = 100...180 bar
Pressure-relief valve.
Discharge returned to suction line
p1 = 5...250 bar
Ordering code
S xxx17 E xxx12 V 15011
The design calculations for pumps are
based on the following parameters:
V [cm3/rev] Displacement
Q [l/min] Delivery
p [bar] Pressure
M [Nm] Drive torque
n [rev/min] Drive speed
P [kW] Drive power
It is also necessary to allow for different
efficiencies such as:
ηv Volumetric efficiency
ηhm
Hydraulic-mechanical
efficiency
ηt Overall efficiency
The following formulas describe the
various relationships.
They include correction factors for
adapting the parameters to the usual
units encountered in practice.
Caution: Diagrams providing approxi-
mate selection data will be found on
subsequent pages.
Design calculations for pumps
V
Q
p
P Mn
[%]
n ηv
QM η
hm p
P ηt
p · Q
Q = V · n · ηv · 10–5
M · ηhm p =
1.59 · V
p · Q
P = 6 · ηt
QV = · 105 n · η
v
M · ηhmV =
159 · p
6 · P · ηtQ =
p
Qn = · 105
V · ηv
1.59 · V · pM = ηhm
6 · P · ηtp =
Q
V [cm3/rev] Q [l/min] p [bar] Caution: η [%] e.g. 95 [%]
n [rev/min] P [kW] M [Nm]
Upon request
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 9/22
Performance charts
0 1000 2000 3000
100
0
10
20
30
40
50
60
80
70
90
110
n [rpm]
Q [
l/m
in]
20
22.5
V =
36 c
m3 /
32
28
25U
rev
p = 20 barp2 = max. intermittent
V = 20 cm3/
n [rpm]
0 1000 2000 3000
0
20
60
40
80
100
120
40
50
30
20
10
0
p = 280 bar
p = 2
80 b
ar
200
250
150
100
50
100
150
200
25050P [
kW
]
M [
Nm
]
Urev
0
20
60
40
80
100
120
140
V = 22.5 cm3/
0 1000 2000 3000
20
10
0
30
40
50
p = 280 bar p =
280
bar
50
100
150
200
250
50
100
150
250
200
Urev
n [rpm]
P [
kW
]
M [
Nm
]
Q = f (n,V) incl. ηv
P = f (n, p) incl. ηt
M = f (n, p) incl. ηhm
ν = 35 mm2/s, ϑ = 50 °C
10/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Performance charts (continued)
n [rpm]
P [k
W]
M [N
m]
V = 28 cm3/Urev
0
20
60
40
80
100
120
140
0 1000 2000 3000
20
10
0
30
40
50 p = 260 bar
p = 2
60 b
ar
50
100
150
200
50
100
150
200
n [rpm]
P [k
W]
M [N
m]
V = 32 cm3/Urev
0
20
60
40
80
100
120
140
0 1000 2000 3000
20
10
0
30
40
50 p = 240 bar
p = 2
40 b
ar
50
100
150
200
50
100
150
200
n [rpm]
P [k
W]
M [N
m]
V = 36 cm3/ Urev
0
20
60
40
80
100
120
160
140
0 1000 2000 3000
20
10
0
30
40
50
p = 210 bar
p =
210
bar
50
100
150
50
100
150
n [rpm]
P [k
W]
M [N
m]
V = 25 cm3/Urev
0
20
60
40
80
100
120
140
0 1000 2000 3000
20
10
0
30
40
50 p = 280 bar
p = 2
80 b
ar
50
100
150
200
250
50
100
150
250
200
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 11/22
Noise charts
Noise level dependent on rotational speed, pressure range
between 10 bar and pressure value p2 (see page 12 Speci-
fications table).
Oil data: ν = 32 mm2/s, ϑ = 50 °C.
Sound pressure level calculated from noise measurements
made in the sound absorbent measuring room compliant with
DIN 45635, Part 26.
Spacing between measuring sensor – pump: 1 m.
These are typical characteristic values for the respective model.
They describe the airborne sound emitted solely by the pump.
Environmental influences (installation site, piping, further
system components) are not taken into consideration.
Each value applies for a single pump.
10000 2000 3000
40
35
30
45
50
55
60
65
70
75
n [rpm]
LpA
[d
B(A
)]
V = 20 cm3/Urev
n [rpm]
LpA
[d
B(A
)]10000 2000 3000
30
40
35
45
50
55
60
75
70
65
V = 22.5 cm3/Urev
n [rpm]
LpA
[d
B(A
)]
10000 2000 300030
35
40
45
50
55
60
65
75
70
V = 25 cm3/Urev
n [rpm]
LpA
[d
B(A
)]
10000 2000 300030
40
35
45
50
60
55
65
70
75
V = 28 cm3/Urev
n [rpm]
LpA
[d
B(A
)]
10000 2000 300030
35
40
45
50
55
60
65
70
75
V = 32 cm3/Urev
n [rpm]
LpA
[d
B(A
)]
10000 2000 300030
35
40
45
50
55
60
65
75
70
V = 36 cm3/Urev
12/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Specification General
Construction External gear pump
Mounting Flange or through-bolting with spigot
Line ports Flange
Direction of rotation
(looking on shaft)
Clockwise or counter-clockwise,
the pump may only be driven in the direction
indicated
Installation position Any
Load on shaft Radial and axial forces after consulting
Ambient temperature range –30 °C...+80 °C or max. +110 °C with FKM seals
Hydraulic fluid – Mineral oil compliant with DIN 51 524, 1–3,
however under higher load at least HLP compliant
with DIN 51 524 Part 2 recommended.
– Comply with RE 90220
– Further operating fluids possible after consultation
Viscosity 12...800 mm2/s permitted range
20...100 mm2/s recommended range
...2000 mm2/s range permitted for starting
Hydraulic fluid temperature
range
max. +80 °C with NBR seals *)
max. +110 °C with FKM seals **)
Filtration ***) At least cleanliness level 20/18/15 compliant with
ISO 4406 (1999)
***) NBR = Perbunan®
***) FKM = Viton®
***) On hydraulic systems or
devices with critical counter-
reaction, such as steering and
counterbalance valves, the type
of filtration selected must be
adapted to
the sensitivity of these devices/
systems.
Safety requirements pertaining
to the whole systems are to be
observed.
In the case of applications
with high numbers of load cycles
please consulting.
Definition of direction of rotation
Always look on the drive shaft.
Caution: Dimensions drawings always show clockwise-rotation
pumps.On counter-clockwise-rotation pumps the positions of
the drive shaft and the suction and pressure ports are different.
Definitions of pressures
p3
p2
p1
p1 max. continuous pressure
p2 max. intermittent pressure
p3 max. peak pressure
max. 20 s
Time t
Pum
p p
ressure
bar
Clockwise rotation Counter-clockwise rotation
AZPT-2x
Displacement V cm3/rev 20 22,5 25 28 32 36
Suction pressure pe
bar
0.7...3 (absolute), with tandem pumps
pe (p
2) = max. 0.5 p
e (p
1)
Max. continuous pressure p1 250 250 250 230 210 180
Max. intermittent pressure p2 280 280 280 260 240 210
Max. peak pressure p3 300 300 300 280 260 230
Min. rotational < 100 rpm 500 500 500 500 500 500
speed at bar 12 mm2/s 100...180 600 600 600 600 600 600
180... p2 800 800 800 800 800 800
25 mm2/s p2 500 500 500 500 500 500
Max. rotational speed at p2 3000 3000 3000 2800 2800 2800
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 13/22
Drive arrangement1. Flexible couplings
The coupling must not transfer any radial
or axial forces to the pump.
The maximum radial runout of shaft
spigot is 0.2 mm.
Refer to the fitting instructions provided
by the coupling manufacturer for details
of the maximum permitted shaft misalign-
ment.
2. Coupling sleeve
Used on shafts with DIN or SAE splining.
Caution: There must be no radial or
axial forces exerted on the pump shaft
or coupling sleeve. The coupling sleeve
must be free to move axially. The dis-
tance between the pump shaft and drive
shaft must be 2+1. Oil-bath or oil-mist
lubrications is necessary.
34
2+1
Ø2
5h11
Splined shaft Ordering
code
Mmax
[Nm]
SAE-B 13 teeth D 320
SAE-C 11 teeth P 180
3. Drive shaft with tang
For the close-coupling of the pumps to
electric motor or internal-combustion
engine, gear, etc. The pump shaft has a
special tang and driver c (not included
in supply).
There is no shaft sealing.
The recommended arrangements and
dimensions for the drive end and sealing
are as follows.
a Drive shaft
Case-hardening steel DIN 17 210
e.g. 20 MnCrS 5
case-hardened 1.0 deep; HRA 83±2
Surface for sealing ring
ground without rifling Rt � 4μm
b Radial shaft seal ring
Rubber-covered seal (see DIN 3760,
Type AS, or double-lipped ring).
Cut 15° chamfer or fit shaft seal ring with
protection sleeve.
R1±0.2
8.8±0.2
min. 8
a
b
c
Ø52
±0.0
46
–0.0
8310
–0.0
25
3.2–0.5
30°
Ø22
..24
Ø37
15
A A0.2
Mmax
[Nm]
V[cm3/rev]
pmax
[bar]
95
20 270
22.5 240
25 220
28 190
32 170
36 150
14/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
4. V-belts and straight gearwheels or
helical toothed gear drives without
outboard bearing
When proposing to use V-belt or gear
drive, please submit details of the appli-
cation for our comments (especially di-
mensions a, dm
, dw and angle α).
For helical toothed gear drives, details of
the helix angle � are also required.
0°
180°
0°
180°
α α
aa
dw
dm
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 15/22
Multiple gear pumpsGear pumps are well-suited to tandem combinations of
pumps in which the drive shaft of the first pump is extended to
drive a second pump and sometimes a third pump in the same
manner. A coupling is fitted between each pair of pumps.
In most cases each pump is isolated from its neighbor, i.e. the
suction ports are separate from one another. A common suction
port is also possible as an option.
Caution: Basically, the specifications for the single pumps
apply, but with certain restrictions:
Max. speed: This is determined by the highest rated pump
speed in use.
Pressures: These are restricted by the strength of the drive
shaft, the through drives and the drivers. Appropriate data is
given in the dimensional drawings.
Pressure restrictions during standard through drive
In the case of series T, the driver for the second pumping stage
can carry a load of up to Mmax.
= 95 Nm, i.e. there is a pressure
restriction for the second stage and any further stages.
Drive shaft Max. transferrable
drive torque *
[Nm]
C 1: 5 200
N Claw 95
D SAE 13t 320
P SAE 11t 180
* These values only apply when the conditions de-
scribed above are complied with. Bosch Rexroth is
to be consulted if the stated values are exceeded.
If the first stage is driven through a tang (driver) or outboard
bearing type 1, pressure restrictions apply as indicated in the
formula below.
Reinforced through drives are available for applications with
higher transfer torques and/or rotational vibrations. Customized
designs available on request.
T T, S
Mmax.
Combinations
Series
pump 1
Mmax.
[Nm] Series
pump 2
T
T
95
65
T
S
For configuration of multiple pumps we recommend the pump
is positioned with the largest displacement on the drive side.
T T, S
Mmax. = 160 Nm
M
Mmax.
� Δp1 · V
1 · 0.0177 + Δp
2 · V
2 · 0.0177 + Δp
3 · V
3 · 0.0177
Δp [bar] V [cm3/rev]
p1 V
1p
2 V
2p
3 V
3
16/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
DimensionsStandard range
55
±1
.5
15
3±
1.5
13
2±
0.2
44
.2±
0.1
88.4±0.2
110±1.5
11±0.135
R 1
0±0.
5
55±0.15
A±0.59±0.2
45.5±0.6B±1.5
12.5±0.3
Ø2
2±
0.5
18
.75
±1
M8depth 13
18
1:5
45° 45°2
Ø1
00
–0
.05
4
20
10.5±0.4
5°4
2'3
8"
±1'
11
0–
0.2
55±0.15
3.8±0.2
2.5±0.1
M8depth 13
Ø9
5.2
–0
.15
4x6.5 DIN 6888
M14x1.5-8-A
DIN 128-A14-FSt
26
45° 45°
12
2.5
–1
12
2.5
+1
.5
As shown in drawing
Inlet and outlet port changed
Ordering code:
AZPT – 22 – □ □ □ □ C B 20 M B
Displacement Ordering-No. Max. operating
pressure
Max. rota-
tion speed
kg Dimension
[mm]
[cm3/rev] L R [bar] [rpm] A B
20 0 517 625 309 0 517 625 008 280 3000 52.0 119.1 M8
13 depth22.5 0 510 725 302 0 517 725 016 280 3000 53.5 122.1
25 0 517 725 313 0 517 725 017 280 3000 55.0 125.1
28 0 517 725 314 0 517 725 018 260 3000 56.5 128.1
32 0 517 725 315 0 517 725 019 240 2800 59.0 132.6
36 0 517 725 316 0 517 725 020 210 2600 61.0 137.1
n N
A 5
17
34
0 0
02
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 17/22
Version 2 Version 1
As shown in drawing
Inlet and outlet port changed
Min. 20.1
usable shaft length
Splined shaft ANSI B 92.1 13T 16/32 DP Tooth thickness Sw = 2.155 – 0.03
M10 depth 18
M10 depth 18
26
.2 ± 0
.25
22
.2 ± 0
.25
47.6 ± 0.25
25
52.4 ± 0.25
25
Ø1
4.3
+ 0.2
7
Ø 2
4
11
0 – 0
.2
Ø 2
1.8
06
– 0.1
27
10 – 0.4
31
42
± 2
R 6
0 ± 1
.1
174 ± 1.9
146 ± 0.15
SAE-B flange
47.6 ± 0.25
M10 depth 18
18
A ± 0.5 9.5 ± 0.1
B ± 1.5
18
.75
± 1
22
.2 ± 0
.25
Ø 1
01
.6 – 0
.05
12
2.5
– 1
12
2.5
+1
.5
A 5
17
341
20
3
Ordering code:
AZPT – 22 – □ □ □ □ D C 07 K B
Displace-
ment
Ordering-No. Max.
operating
pressure
Max.
rotation
speed
kg Dimension
[mm]
Version
[cm3/rev] L R [bar] [rpm] A B C D
20 0 517 625 310 0 517 625 009 280 3000 52.0 119.1 25 47.6 M10
18
depth
1
22.5 0 517 725 317 0 517 725 021 280 3000 53.0 122.1 25 52.4 2
25 0 517 725 318 0 517 725 022 280 3000 55.0 125.1 25 52.4
28 0 517 725 319 0 517 725 023 260 3000 56.5 128.1 25 52.4
32 0 517 725 320 0 517 725 024 240 2800 59.0 132.6 25 52.4
36 0 517 725 321 0 517 725 025 210 2600 61.0 137.1 25 52.4
n N
DimensionsStandard range
18/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Fittings Fittings can be used for rectangular flange 20 see page 7
Gear pump flange, 90° angle
LA
S1
L2
L1
L3
L4
L5
Ø D3
Ø D1
Ø D1
LK
Ø D
B
LA
LK D1 D3 L1 L2 L3 L4 L5 LA S1 DBScrews Seal
ring
Mass
kgPart number
p(bar)2 pcs. 2 pcs.
55 20S 17 45 34.5 24.0 40.0 56.0 58 36 8.4 M 8x25 M 8x50 33x2.5 0.44 1 515 702 004 250
55 30S 26 49 35.5 32.0 50.0 62.0 58 50 8.4 M 8x25 M 8x50 33x2.5 0.50 1 515 702 006 250
55 35L 31 49 38.5 32.0 51.5 62.0 58 50 8.4 M 8x25 M 8x60 32x2.5 0.47 1 515 702 005 100
55 42L 38 49 38.0 40.0 64.5 61.0 58 60 8.4 M 8x25 M 8x70 32x2.5 0.60 1 515 702 019 100
Complete fittings with seal ring, metric screw set, nuts and olive.
Note
You can find the permissible tightening torques in our publication:
“General Operating Instructions for External Gear Units”
RE 07 012-B1.
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 19/22
3
31
Single pump
Page Ordering code
Seal kit “T”
Pos. 800
NBR
Shaft seal ring
Pos. 3 Dimension
Seal ring
Pos. 31 Material Dimension
16 AZPT – 22 – □ □ □ □ C B 20 M B 1517010226 1510283023 40x22x7 – NBR
17 AZPT – 22 – □ □ □ □ D C 20 K B 1517010226 1510283028 40x22x7 – FKM (SSR)
NBR = Perbunan® FKM = Viton®
Multiple pump
Service parts
20/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Notes for commissioningFilter recommendation
The major share of premature failures in external gear pumps is
caused by contaminated hydraulic fluid.
As a warranty cannot be issued for dirt-specific wear, we re-
commended filtration compliant with cleanliness level 20/18/15
ISO 4406, which reduces the degree of contamination to
a permissible dimension in terms of the size and concentration
of dirt particles:
Operating pressure [bar ] >160 <160
Contamination class ISO 4406 18/15 19/16
To be reached with βX = 75 20 25
We recommend that a full-flow filter always be used.
Basic contamination of the hydraulic fluid used may not
exceed class 20/18/15 according to ISO 4406. Experience has
shown that new fluid quite often lies above this value. In such
instances a filling device with special filter should be used.
General
– The pumps supplied by us have been checked for function
and performance. No modifications of any kind may
be made to the pumps; any such changes will render the
warranty null and void!
– Pump may only be operated in compliance with permitted
data (see pages 15 – 18).
Project planning notes
Comprehensive notes and suggestions are available in
Hydraulics Trainer, Volume 3 RE 00 281, “Project planning
notes and design of hydraulic systems”. Where external gear
pumps are used we recommend that the following note be
adhered to.
Technical data
All stated technical data is dependent on production toler ances
and is valid for specific marginal conditions.
Note that, as a consequence, scattering is possible, and at
certain marginal conditions (e.g. viscosity) the technical data
may change.
Characteristics
When designing the external gear pump, note the maximum
possible service data based on the characteristics displayed
on pages 10 to 12.
Additional information on the proper handling of hydraulic
products from Bosch Rexroth is available in our document:
“General product information for hydraulic products”
RE 07 008.
Contained in delivery
The components with characteristics as described under
ordering code and device measurements, pages 16 – 17,
are contained in delivery.
You can find further information in our publication:
“General Operating Instructions for External Gear Units”
RE 07 012-B1.
Hydraulics Bosch Rexroth AGAZPT RE 10 092/02.12 21/22
The AZ configurator at www.boschrexroth.com/azconfigurator
The AZ configurator assists you to con-
figure your individual external gear unit
easily and user-friendly. You only need to
specify your requirements: From the
displacement, direction of rotation, drive
shaft, connection flange right up to the
required rear cover. You immediately
receive a project drawing (PDF format) if
a configuration already exists. You receive
the price of the configured external gear
unit upon request.
The AZ configurator
assists you to configure
your individual external
gear unit easily and user-
friendly – all data needed
for project planning are
acquired thru menu guid-
ance.
Selection is made either
on an ordering code or
your technical require-
ments. This means that
you can search for exter-
nal gear units that have
already been configured,
or you specify the con-
figuration variant of the
external gear unit based
upon the operating para-
meters you require.
If the external gear unit
you selected has been
released you will receive
the part number, ordering
code and a detailed
installation drawing. If
your special configuration
is not available please
send your specification
to Rexroth. One of our
employees will then
contact you.
Bosch Rexroth AG
External Gear Units
Robert-Bosch-Straße 2
D-71701 Schwieberdingen
Telefon +49 (0) 711-811 10 63
Telefax +49 (0) 711-811 17 98
www.boschrexroth.com/brm
© This document, as well as the data, specifications and other information
set forth in it, are the exclusive property of Bosch Rexroth AG. It may not
be reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No state-
ments concerning a certain condition or suitability for a certain application
can be derived from our information. The information given does not release
the user from the obligation of own judgement and verification. It must be
remembered that our products are subject to a natural process of wear and
aging.
22/22 Bosch Rexroth AG Hydraulics AZPT RE 10 092/02.12
Ordering-No.
Ordering-No. Page
0 517 625 008 16
0 517 625 009 17
0 517 625 309 16
0 517 625 310 17
0 517 725 016 16
0 517 725 017 16
0 517 725 018 16
0 517 725 019 16
Ordering-No. Page
0 517 725 020 16
0 517 725 021 17
0 517 725 022 17
0 517 725 023 17
0 517 725 024 17
0 517 725 025 17
0 517 725 302 16
0 517 725 313 16
Ordering-No. Page
0 517 725 314 16
0 517 725 315 16
0 517 725 316 16
0 517 725 317 17
0 517 725 318 17
0 517 725 319 17
0 517 725 320 17
0 517 725 321 17