Download - Reactive Power Compensation using STATCOM
![Page 1: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/1.jpg)
REACTIVE POWER COMPENSATION USING STATCOM
PRESENTED BY NEHA L. JAIN CB.EN.U4EEE13034
1
![Page 2: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/2.jpg)
OBJECTIVE• What is Power Quality• Why Reactive Power Compensation is needed• Introduction to STATCOM and its working • How STATCOM helps in increasing the reliability of power supply from the utility grid – using MATLAB/SIMULINK results
2
![Page 3: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/3.jpg)
POWER QUALITY • Availability of Reliable Power required for proper operation of all end user equipments• Power Quality disturbance is defined as any change in Power, Voltage, Current or Frequency that interferes with the normal operation of the electrical equipment[4]• Most commonly faced power quality issues are Transients Undervoltage / Sag Overvoltage / Swell Harmonic distortion
3
![Page 4: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/4.jpg)
WHY REACTIVE POWER COMPENSATION ?• Energy storage elements
(Inductor/Capacitor) requires Reactive Power (Q) for their operation
• Most of the loads are inductive in nature
• Q reduces Power Factor, and hence increases current flow through the line for the same required active power
• Also Q reduces the voltage at the receiving end
4
![Page 5: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/5.jpg)
BENEFITS OF REACTIVE POWER COMPENSATIONReduced tariff
(penalty for excessive Q consumption)
Improved efficiency
Improved voltage regulation
Better performance of the Power System on the whole
5Figure 1: Power Triangle
![Page 6: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/6.jpg)
INTRODUCTION TO FACTS• FACTS (Flexible Alternating current Transmission System) refers to a family of power electronics based devices to enhance the AC system controllability and stability and to increase power transfer capability[5]
• FACTS Controllers are broadly classified into two types Series controllers Shunt controllers• Series controllers – inject voltage in series with the transmission line• Shunt controllers – inject current into the transmission line
6
![Page 7: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/7.jpg)
STATCOM STATCOM - Static Synchronous Compensators • Shunt Controller • Can either provide or absorb Reactive power• Uses force – commutated power electronic devices like GTO, IGBT• Mostly applied in long transmission lines and are useful for many purposes namely Power Factor Correction Voltage support and control Harmonic suppression 7
![Page 8: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/8.jpg)
FUNCTIONAL DIAGRAM OF STATCOM
8
COUPLING TRANSFORMERVAC
VSC
VOUTIAC
CDC
VDCIDC
BUS
Figure 2: Diagram of STATCOM
![Page 9: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/9.jpg)
VOLTAGE SOURCE CONVERTER
9Figure 3: Circuit diagram of VSC
![Page 10: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/10.jpg)
OPERATION OF STATCOM• Principle: Two AC sources of same frequency
when connected through a series inductance, Reactive power flows from higher voltage magnitude to lower voltage magnitude
• When voltage angle changes, Real Power flows
• When voltage magnitude changes, Reactive Power flows
• Control schemes for STATCOM Direct control scheme Indirect control scheme
10
![Page 11: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/11.jpg)
SIMULATION – WITHOUT STATCOM
11
Figure 4: Simulink model without STATCOM
![Page 12: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/12.jpg)
SIMULATION RESULTS For input peak voltage of 80 V, RL load
12
PS
(W)
QS
(Var)
PR
(W)
QR
(Var)
VLOAD
(V)
14.12 95.68 7.705 77.05
60
13.47 83.77 8.773 70.19
65
13.15 69.23 10.08 60.45
70
13.1 51.28 11.68 46.73
75
Table 1: Results of Simulink model without STATCOM
![Page 13: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/13.jpg)
SIMULATION – WITH STATCOM
13
Figure 5: Simulink model with STATCOM
![Page 14: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/14.jpg)
SIMULATION RESULTS
14
PS
(W)
QS
(Var)
PR
(W)
QR
(Var)
VLOAD
(V)
15.14 78.02 8.7 87.01 80
14.34 68.57 9.657 77.26 80
13.8 58.33 10.73 64.38 80
13.62 47.53 11.91 47.66 80
For input peak voltage of 80 V, RL load with STATCOMTable 2: Results of Simulink model with STATCOM
![Page 15: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/15.jpg)
ADVANTAGES OF STATCOM• Smooth Voltage control over a wide range of operating conditions • Improves transmission reliability and power quality to a great extent • Fast response than many other FACTS devices• Useful for a variety of power quality issues• Feasible and Economic to implement
15
![Page 16: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/16.jpg)
REFERENCES1. N. G. Hingorani, L. Gyugyi, Understanding FACTS
Concepts and technology of Flexible AC Transmission Systems, New York, 1999, pp: 1-20, 179-195.
2. V.S. Tejwani, H.B. Kapadia, A.S. Pandya, J.B. Bhati, Power Quality Improvement in Power Distribution System using D-STATCOM, IEEE Engg (NUiCONE), pp: 1-6, Nov. 2013.
3. R.Abidi, M.Nour, Analysis of a D-STATCOM in a 25kV Power Distribution Systems using Simulink, International Journal of Electrical and Electronics research, Vol. 2, Issue 2, pp: (26-34), Month: April - June 2014.
4. A. E. Xavier, STATCOM and its Simulink Model, [Online]. Available: http://shodhganga.inflibnet.ac.in/bitstream/10603/22975/7/07_chapter%202.pdf
16
![Page 17: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/17.jpg)
REFERENCES ctd.,5. J. George, “ Reactive Power Compensation
using Multilevel Inverter based STATCOM”, India, July 2011.
6. N. Rana, S. Agarwal, Reactive Power Compensation using STATCOM, International Journal of Computer Applications, Kurukshetra,
7. G.E. Valderrama, “Reactive power and imbalance compensation using STATCOM with dissipativity-based control”, IEEE Trans. Control System Technology, vol:9, Issue:5, pp: 718 - 727
8. M. G. G Titus, “ Reactive Power Compensation using STATCOM for single phase distribution system”, Circuit, Power and Computing Technologies, pp: 1-5.
17
![Page 18: Reactive Power Compensation using STATCOM](https://reader037.vdocuments.site/reader037/viewer/2022100208/577c84c01a28abe054ba3357/html5/thumbnails/18.jpg)
THANK YOU
PRESENTED BY NEHA L. JAIN CB.EN.U4EEE13034
18