(2.5” capsule version)
Operation Manual
www.universal-space.com
Pirate’s Hook manual Rev.1.0
08/02/2017
1
Have Questions? Contact us!
www.universal-space.com
International Support Center North America Service Support Center
Tel: +1-905-477-2823
Fax: +1-905-477-2660
Email: [email protected]
Tel: 972-241-4263
Fax: 214-919-4918
Email:[email protected]
Pirate’s Hook Manual Rev.1.0
08/02/2017 2
CONTENT
IMPORTANT SAFETY INSTRUCTIONS .................................................... 3
1. SPECIFICATIONS ................................................................................ 5
2. PACKAGE CONTENTS ......................................................................... 6
3. PART NAME ........................................................................................ 7
4. SET UP & INSTALLATION ................................................................... 8
5. HOW TO PLAY ................................................................................... 11
6. GAME OPTION .................................................................................. 12
8. MAINTENANCE & INSPECTION ........................................................ 17
9. OVERALL CONSTRUCTION ............................................................... 18
10. WIRING DIAGRAM ......................................................................... 28
Pirate’s Hook manual Rev.1.0
08/02/2017
3
Thank you for purchasing Pirate’s Hook from Universal Space. We hope you enjoy the product.
This manual contains valuable information about how to operate and maintain your game machine properly and safely. It is intended for the owner and/or personnel in charge of product operation. Carefully read and understand the instructions. If you need any help during installation and setup please utilize this manual and troubleshooting guide. If the product fails to function properly, non-technical personnel should under no circumstance attempt to service the machine. Contact your distributor or manufacturer for help. Before use, please read IMPORTANT SAFETY INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
To ensure the safe usage of this product, carefully read and understand these instructions before operating your game. Save these instructions for future reference. Use this product only as described in this manual. Other uses not recommended may cause fire, electric shock or personal injury. Unplug the game from the outlet when not in use, when moving from one location to another, and before cleaning/servicing. Explanations which require special attention are indicated by signs of warning. Depending on the potential hazardous degree, the terms: NOTE, NOTICE, and WARNING are used. NOTE: A NOTE indicates useful hints or information about product usage. NOTICE: A NOTICE indicates potential damage to product and how to avoid the problem. WARNING: A WARNING indicates a potential for product damage or serious personal Injury. It is important to understand the meaning of the following HAZARD SIGNS before continuing:
High Voltage and Shock Hazard:
High voltage can cause electric shock.
Turn off/unplug power before servicing.
High Temperature Hazard: This part may cause scalding.
Do not touch. Surface may be hot.
No Touching Hazard: This part may be hot or can cause electric shock. Do not touch.
Pirate’s Hook Manual Rev.1.0
08/02/2017 4
Use the following safety guidelines to help ensure your own personal safety and to help protect your equipment and surrounding environment from potential damage.
This product is an indoor game machine. Do not install
outdoors.
Avoid installing in the following places to prevent fire, electric shock, injury
and/or machine malfunctioning:
Places subject to rain/moisture, or places subject to high humidity.
Places subject to direct sunlight, or places subject to extremely hot or cold
temperatures to ensure that it is used within the specified operating range.
Places where inflammable gas may be present or in the vicinity of highly
inflammable/volatile chemicals or items that can easily catch fire
On unstable or sloped surfaces. The machine may topple or cause unforeseen
accidents.
Vicinity of fire exits, fire extinguishers etc that may block/prevent safety measures
IMPORTANT NOTE:
ALL REPAIRS MUST BE DONE TO ORIGINAL MANUFACTURER SPECIFICATIONS.
FAILURE TO DO SO VOID ALL WARRANTIES AND OPERATOR ASSUMES ALL
RISKS.
Note: The contents of this manual may be updated without notice.
Pirate’s Hook manual Rev.1.0
08/02/2017
5
1. SPECIFICATIONS
Rated power supply: AC110V 50/60Hz
Min. Power consumption: 45W
Max. Power consumption:60W
Dimensions: W665×D480×H1730(mm)
Weight: Approximately 79kg
Part No: P126
NOTICE: After turning off the game, please wait at least 1 minute
before restarting again.
Note: Game parameters are subject to change without notice.
NOTICE: After turning off the game, please wait at least 1 minute before
restarting again.
Pirate’s Hook Manual Rev.1.0
08/02/2017 6
2. PACKAGE CONTENTS
Open the package and make sure all the items are included:
1. 1 x Body Assembly
2. Following accessories
NOTE: Part models are subject to change without notice.
No. Part No. Code No. Name Spec. Qty Picture
1 P126-421-000 23301010019 Power cord 3×16AWG 1.8m 1
2 P126-424-000 21901000010 Fuse T3A/250VAC Φ5X20mm
1
3 P126-422-000 41300000005 Memory
stick 8G 1
4 P126-727-000 41440000116 Manual ENGLISH 1
5 P126-419-000 25300171002 Key 171 1 6 P126-420-000 25300172002 Key 171B 1
Pirate’s Hook manual Rev.1.0
08/02/2017
7
3. PART NAME
Marquee Assembly
Monitor Assembly
Confirm Button
Prize Outer
Sides Marquee Assembly
Controller Assembly
Speaker Assembly
Coin Assembly
Pirate’s Hook Manual Rev.1.0
08/02/2017 8
4. SET UP & INSTALLATION
This product is an indoor game machine. Do not install
outdoors.
Refer to IMPORTANT SAFETY INSTRUCTIONS (Pg. 2) for places to avoid Place the unit on a dry level surface Ventilation openings in the back of the unit must not be obstructed by objects or by
wall.
4.1 Play Zone This machine requires space for playing and for maintenance as shown below. Leave space around the game upon installation:
Service area: 250mm
Play area: 500mm
Service area
Play area
Pirate’s Hook manual Rev.1.0
08/02/2017
9
4.2 Level Adjustment Install this machine on a flat surface. Adjust levers to lift casters off the ground to level the game. If the game is installed on an unsuitable floor, it could cause game malfunction. To secure the game, adjust the Leveler down until it touches the floor, lifting the casters off the ground by 5mm. Repeat the same for all levelers.
4.3 Transporting the Game If you need to move the game, adjust the levelers back to an “up” position so the casters touch the ground.
NOTICE
Be careful not to damage the machine during transport. The machine should be handled with care when bringing it down from a higher level. Always unplug the game before moving. Keep the machine in upright position during transport. For longer distance transport, package the game properly to prevent damages.
Leveler Caster
About 5 mm
Move Fix
Make sure the machine is level with the ground and all the adjustable legs should stick to the floor closely.
NOTICE
Leveler Caster
Move
Pirate’s Hook Manual Rev.1.0
08/02/2017 10
4.4 Connecting Power
WARNING: Check the voltage rating before you connect the equipment to an electrical outlet to ensure that the required voltage and frequency match the available power source. Please refer the label of the machine.
Do not plug the equipment power cables into an electrical outlet if the power cable is damaged.
Avoid putting many loads on one electrical outlet as it could generate heat and fire resulting from overload.
Connect the grounding conductor to the earth terminal (GND):
WARNING Ensure no heavy objects rest on the power cord. Check to make sure the game cabinet does not sit on the power cord as this could damage the cord and become hazardous.
To disconnect the game, grip the plug and pull it from the wall outlet. Never pull by the cord.
To prevent electric shock, do not touch the power plug when hand is wet.
Ensure that nothing rests on the power cord and that it is not located where it can be stepped on or tripped over.
Power socket
Power outlet
Power plug
Power cord Power plug
Pirate’s Hook manual Rev.1.0
08/02/2017
11
5. HOW TO PLAY
Pirate’s Hook Manual Rev.1.0
08/02/2017 12
6. GAME OPTION Open the front door and there is a meter on the coin box. Press Test button on the meter and get into the setting menu.
Main Menu
English Note
1 Game Mode 2 Input Test 3 Output Test 4 Game Reset 5 Language 语言选择 EN/CN 6 Time Setting 7 Book Keeping 8 Exit Without Save 9 Exit & Save
Game Mode(Version 1.0.12)
English Note 1 Free Play ON/OFF 2 Coins per Round 1-10 3 Mercy Capsule OFF/1/2/3 4 Average prize out 1-20 Game/prize 5 1 prize = X coins X= Coins per Round x Average prize out 6 Average Score 5-100 score/game 7 Target Score 8 Lobster King Appears every 1-60(s) 9 Auto Play Time 5-60(s)
10 Game Duration 5-90(s) 11 Resistance test 1-5 12 Resistance Setting 13 Fish Score Display ON/OFF 14 Is Save Coins ON/OFF 15 Background Sound ON/OFF 16 Volume 0-10 15 Back
-Vol+
Pirate’s Hook manual Rev.1.0
08/02/2017
13
Target Score
1 S Fish 0-100
2 M Fish 0-100
3 L Fish 0-200
4 Rublish 0-10
5 Shark 0-500
6 Octopus 0-500
7 Lob Fish 0-2000
8 Back
Pirate’s Hook Manual Rev.1.0
08/02/2017 14
Resistance Setting
1 S Fish 1-7
2 M Fish 1-7
3 L Fish 1-7
4 Rubbish 1-7
5 Shark 1-7
6 Octopus 1-7
7 Lob Fish 1-7
8 Back
Input Test Output Test Game Reset English Note 1 Coin Mech ON/OFF 2 Server Button ON/OFF 3 Repair Button ON/OFF 4 Lower Hook ON/OFF 5 Door Switch ON/OFF 6 Back Date/Time Setting Bookkeeping English Note
1 Year 2 Month 3 Day
4 Hour 5 Minute 6 Second 7 Back 8 Back & Apply
English Note 1 Reset Configs 2 Clear All Records 3 Clear Out Prize 4 Clear Insert Coins 7 Back
English Note 1 Lower Hook Light ON/OFF 2 Resistance 0-7 3 Out Prize ON/OFF 4 Shake ON/OFF 5 Big Bonus 0-10 6 Back
English Note
1 Payer 2 Insert Coins 3 Used Coins 4 Prize out 5 Earned Coins 6 Prize out / game 7 Back
Pirate’s Hook manual Rev.1.0
08/02/2017
15
7. ERROR MESSAGE AND RECOVERY 7.1 Trouble Shootings Please confirm whether every connector connected tightly.
Troubles Cause Methods
Cannot start with power on
Power source not fit Check and replace it Residual current circuit breaker
turned off Check and turn it on
Voltage is not 110V Replace the power source
Blank screen with Open
WINDOWS sound and power on
VGA signal line loosen Draw and insect it. If not for the supply
port, check VGA signal line
Monitor broken Change monitor. Please call
4006-020-321 for after-sales service
Game procedure reports error Update game again
Start normally but crash sometime
in process
Video card loosen or not touch firmly
Reinstall the video card
Computer crash Restart it or restore system
No reaction from coin mech.
Coin mech. broken Replace coin mech Coin mech’s signal line loosen Check and fasten it
Not in DC12V Change the voltage of power switch IO control-panel broken Replace IO control-panel
Start normally but without sound
Volume shut down Adjust volume Audio cable loosen Check and fix it
Power amplifier broken Replace power amplifier Loudspeaker broken Replace loudspeaker
Start normally but cannot enter
gaming scene
VGA signal line loosen Check if it is connected with IO firmly IO control-panel broken Replace IO control-panel
Dongle broken Replace dongle
Lights not work
DC12V connecting line loosen Check and fasten it Switch power source broken Replace power source
DC12V short circuit Check and eliminate it Light control-panel broken Replace control-panel
Pirate’s Hook Manual Rev.1.0
08/02/2017 16
7.2 System Recovery Operation 1. Turn off the game. Insert the memory stick into the USB port at the back of the computer. 2. Restart PC to enter the system recovery screen as shown. 3. The game will automatically start
recovery which will last about 5 minutes.
Please wait until process is complete.
WARNING: the USB flash drive should only be used to fix software errors. Using it for
other purposes may cause unexpected results and damages.
4. Once system recovery is finished (as shown on
the left), remove the USB flash drive from the
computer and turn off the PC. Wait at least 30
seconds before restarting the PC.
Pirate’s Hook manual Rev.1.0
08/02/2017
17
8. MAINTENANCE & INSPECTION 8.1 Safety Check
Check the points listed before operating the machine. These checks are necessary for safe machine operation: 1. Try to run the game before operation each day. 2. Conduct monthly routine checks of game components ensure good working condition 3. Check the machine regularly for dust and clean when necessary. Note: Parts and components require preventative maintenance to be kept running smoothly
8.2 Handling Precautions
When installing or inspecting the machine, be very careful of the following points and pay attention to ensure that the player can enjoy the game safely.
Non-compliance with the following points or inappropriate handling running counter to the cautionary matters herein stated can cause personal injury or damage to the machine
• Before servicing the machine, be sure to turn power off. Servicing without turning the power off can cause electric shock or short circuit. • To avoid electric shock or short circuit, do not plug then unplug the power quickly • Do not expose power cords and earth wires, these are susceptible to damage. • Damaged cords and wires can cause electric shock or short circuit and should be replaced immediately. • When or after installing the product, avoid pulling the power cord to prevent unnecessary wear and tear. Use the power button to disconnect power. • In case the power cord is damaged, ask for replacement through where the product
was purchased from or replace locally. Continued usage of damaged cord can cause fire, electric shock or leakage.
• Perform grounding appropriately. Inappropriate grounding can cause electric shock. • Use fuses that meet specified rating. Fuses exceeding can cause an electric
shock. • Should a problem occur, turn off the power immediately and stop operating the
machine. Unplug the power cord of the service outlet. Operating the machine without correcting the problem may cause a fire or injuries.
• Insert the power plug securely into the outlet. Poor contact may cause overheating, resulting in fire or burns.
• To ensure the warning labels attached on the machine are visible and legible, install the machine in a well-lit location, and keep the labels clean at all times. Make sure the labels are not hidden behind other game machines.
WARNING
Pirate’s Hook Manual Rev.1.0
08/02/2017 18
9. OVERALL CONSTRUCTION 9.1 Mechanical Part 9.1.1 Marquee Assembly
No. Part No. Code Name Material Qty
1 P126-123-000 20241341H020 Front door plate Q235 1
2 P126-125-000 20241341H019 Prize box Stainless steel201 1
3 P126-163-000 26000062000 Coin inner box Black ABS 1
4 P126-149-000 20211406K001 Front panel Q235 1
5 P126-126-000 20241341H006 Coin rail Q235 1
6 P126-161-000 26000044000 Meter bracket Metal 1
7 P126-408-000 25300172001 Lock 171B 1
Pirate’s Hook manual Rev.1.0
08/02/2017
19
9.1.2 Cabinet Assembly
Pirate’s Hook Manual Rev.1.0
08/02/2017 20
No. Part No. Code Name Material Qty
1 P126-135-000 20241341H013 Funnel fixed plate Q235 2
2 P126-137-000 20241341H015 Ball box fixed plate
A Q235 4
3 P126-134-000 20241341H012 Ball funnel Q235 1
4 P126-445-000 22702000010 Exhaust fan net 4 inch 2
5 P126-444-000 22702010025 DC exhaust fan XW-1238M12S
DC12V 0.4A 1
6 P126-136-000 20241341H014 Ball box Q235 1
7 P126-142-000 20241341H016 Ball box handle Q235 2
8 P126-143-000 20641341H004 Observation door Plexi. 1
9 P126-148-000 20641341H006 Spring sleeve White nylon 1
10 P126-147-000 20241341H024 Lift plate Q235 1
11 P126-107-000 20241324B017 Iron Q235 2
12 P126-101-000 20241324B006 Battery platen Q235 1
13 P126-158-000 26000014000 Window shades Q235 1
14 P126-160-000 26000042000 Wiring box Assy. 1
15 P126-156-000 26000001000 SW power supply
base Metal 1
16 P126-108-000 20241324B018 Iron Q235 1
17 P126-131-000 20241341H021 Fixed plate A Metal 2
18 P126-132-000 20241341H022 Fixed plate B Metal 2
19 P126-129-000 20241341H001 Lock pin Metal 1
20 P126-130-000 20241341H017 Lock bolt 45# 2
Pirate’s Hook manual Rev.1.0
08/02/2017
21
9.1.3 Control Panel Assembly
Pirate’s Hook Manual Rev.1.0
08/02/2017 22
No. Part No. Code Name Material Qty
1 P126-704-000 20511406K003 Marquee decal δ5 plexi. 1
2 P126-127-000 20241341H008 Marquee R support plate Q235 1
P126-128-000 20241341H009 Marquee L support plate Q235 1
3 P126-102-000 20641324B001 Light cover PC 1
4 P126-151-000 20211406K003 Top marquee Q235 1
5 P126-707-000 20541341H004 Pop board decal POP+ sticker 1
6 P126-704-000 20541341H001 Monitor decal δ5 plexi. 1
7 P126-110-000 20641324B005 Monitor EVA bar Black EVA 1
8 P126-105-000 20241324B016 Vacuum foam fixed plate Q235 2
9 P126-111-000 20241324B020 R light cover Yellow ABS 1
10 P126-112-000 20241324B021 L light cover Yellow ABS 1
11 P126-109-000 20241324B036 Iron chain Stainless steel 1
12 P126-106-000 20241324B035 Hinge 2 Stainless steel 1
13 P126-705-000 20541341H002 Control panel decal δ5 plxei. 1
14 P126-103-000 20241324B031 Control panel fixed frame Q235 1
15 P126-406-000 25102000001 Stainless steel buckle C124 1
16 P126-124-000 20241341H005 DBV cover Q235 1
17 P126-150-000 20211406K002 Control panel Q235 1
18 P126-010-000 29941341H004 Capsule Assy. Assy. 1
Pirate’s Hook manual Rev.1.0
08/02/2017
23
9.1.4 Stick Assembly
No. Part No. Code Name Material Qty
1 P126-122-000 20641341008 Bolt Q235 1
2 P126-120-000 20641341006 Outer ring PC 1
3 P126-400-000 20241341019 Turntable welded Assy.
1
4 P126-401-000 20106000060 Deep groove ball br. 6202ZZ 2
5 P126-405-000 23413000004 Hollow br. Magnetic
powder 24V 0.3NM 1
6 P126-402-000 20115005007 A type flat key 5×5×10 1
7 P126-118-000 20641341004 Rotation handle Nylon 1
8 P126-403-000 20741341101 Shake motor 6-24V 1
9 P126-114-000 20641341003 Br. base PC 1
10 P126-121-000 20641341007 Base PC 1
11 P126-302-000 20105000152 B type circlip do15 2
12 P126-119-000 20641341005 End cap PC 1
7
12
2
Pirate’s Hook Manual Rev.1.0
08/02/2017 24
9.1.5 Capsule Assembly
No. Part No. Code Name Material Qty
1 P126-145-000 20241341H002 Capsule plate Metal 1
2 P126-146-000 20241341H023 Sweep ball spring 65Mn 2
3 P126-453-000 21705000006 Sensor PCB HW2558.PCB 2
4 P126-154-000 26000060002 2.5” capsule
plate B ABS 1
5 P126-152-000 26000060001 2.5” capsule
plate A ABS 1
6 P126-155-000 20241341H010 Detector tube Q235 1
7 P126-404-000 23404000107 DC gear motor Z2D6-12GN-18S/2GN180K 1
Pirate’s Hook manual Rev.1.0
08/02/2017
25
9.1.6 Castor Assembly
No. Part No. Code Name Material Qty
1 P126-157-000 26000009000 Leveller Q235 4
2 P126-409-000 25501000003 Castor 2” 2069-44 4
3 P126-113-000 20241324B028 Castor plate Q235 4
Pirate’s Hook Manual Rev.1.0
08/02/2017 26
9.2 Electrical Assembly
.
1
4
10
17
9
3
7
6
5 13
18
14
15 16
2
11
19
8
Pirate’s Hook manual Rev.1.0
08/02/2017
27
No. Part No. Code Name Material Qty
1 P126-432-000 29741341004 Eyes light WXXGC-LED1.PCB(V1.0) 2
2 P126-447-000 22002013003 Prize light DC12V 3528LED 60z/m white 0.15
3 P126-447-000 22002013003 Sides light DC12V 3528LED 60z/m white 1
4 P126-441-000 22402000201 Confirm button 57-1820-02 1
5 P126-433-000 21201021003 Monitor 21.5” 1
6 P126-446-000 22801000047 Speaker 15W 1
7 P126-431-000 29741341005 Controller light 22XHD-DGLED.PCB(V1.0) 2
8 P126-448-000 22003080009 Prize out light W5630-LC40cm-60z/m-DC12V 1
9 P126-440-000 22301000001 Coin mech. 1
10 P126-451-000 23309000188 Wirings 1
11 P126-428-000 21107210020 A31S android
PCB MB-A31S(V2.0) 1
12 P126-435-000 23307010003 DVI convert HDMI
video cable DVI-HDMI(1.0M) 1
13 P126-427-000 21602000094 Power supply MW-S-150-12(12V/12.5A) 1
14 P126-429-000 21107210021 Battery HSLD350709,3.70V/2500mAh 1
15 P126-426-000 22601000005 Rocker SW T125/55 1
16 P126-424-000 21901000010 Fuse Φ5×20mm T3A 250VAC 1
P126-418-000 21902000006 Fuse base R3-11 110V/250V/10A 1
17 P126-434-000 23301018002 Power cord 3x18AWG 0.5M UL 1
18 P126-417-000 23201000001 Filter YB10A1 10A/250V 1
19 P126-436-000 23000000006 Meter C-012 12VDC 18CPS 2
20 P126-437-000 22402030002 Green button PB:11C02R 1
21 P126-438-000 22402050001 Black button PB:11C02R 1
22 P126-439-000 22402010002 Red button PB:11C02R 1
Pirate’s Hook Manual Rev.1.0
08/02/2017 28
9.3 Decals9
No. Part No. Code No. Name Material Qty 1 P126-707-000 20541341H004 POP decal POP 1 2 P126-706-000 20541341H003 Marquee decal δ5 plexi. 1 3 P126-703-000 20541341A006 Confirm button decal PVC100u 1 4 P126-701-000 20541341005 Fishing mechanism L decal 0.3 PVC 1 5 P126-702-000 20541341A005 Fishing mechanism R decal 0.3 PVC 1 6 P126-705-000 20541341H002 Control decal δ5 plexi. 1 7 P126-708-000 20541341H005 L decal PVC 1 8 P126-709-000 20541341H006 R decal PVC 1 9 P126-710-000 20541341H007 Prize out decal PVC 1
10 P126-704-000 20541341H001 Monitor decal δ5 plexi. 1
Pirate’s Hook manual Rev.1.0
08/02/2017
29
No. Part No. Code No. Name Material Qty 1 P126-711-000 20511406K012 Meter label PVC100u 1 2 P126-719-000 25600000067 Service notice label PVC100u 1 3 P126-718-000 25600000042 Service notice label 1 PVC100u 1 4 P126-724-000 25600000095 New service label(large) PVC100u 1
5 P126-712-000 20511406L001 Un-certification 220V
nameplate 1mmpvc 1
6 P126-714-000 20511406L003 Dongle label PVC100u 1
7 P126-713-000 20511406L002 Un-certification 110V
nameplate 1mmpvc 1
8 P126-726-000 20541341H010 Capsule instruction PVC100u 1 9 P126-722-000 25600000073 Fuse T3A/250V PVC100u 1
10 P126-721-000 25600000072 New voltage 220V PVC100u 1 11 P126-720-000 25600000071 New voltage 110V PVC100u 1 12 P126-723-000 25600000091 GND label PVC100u 1 13 P126-715-000 25600000017 Power SW label B PVC100u 1 14 P126-716-000 25600000036 High voltage warning (Small) PVC100u 2 15 P126-717-000 25600000037 High voltage warning (Large) PVC100u 1 16 P126-725-000 25600000096 New service label(Small) PVC100u 1
Pirate’s Hook Manual Rev.1.0
08/02/2017 30
12
34
56
78
ABCD
87
65
43
21
D C B A
Des
ign
Dra
win
g
Col
late
Che
ck
T
echn
ics
Stan
dar
d
App
rove
Un
iver
sal
Spa
ce
Am
use
me
nt m
ach
ine
UN
IS123456789
ABCDEFGHI
Bro
wn
Red
Ora
nge
Yel
low
Gre
enB
lue
Vio
let
Gra
yW
hite
Bla
ckPi
nk L
ight
Gre
enL
ight
Blu
e S
hield
ing
laye
r
JKLMNOPQR
AW
G30
UL
100
7A
WG
28 U
L1
007
AW
G26
UL
100
7A
WG
24 U
L1
007
AW
G22
UL
100
7A
WG
20 U
L1
007
AW
G18
UL
100
7A
WG
16 U
L1
005
AW
G14
UL
100
5
Not
ice:
The
col
or a
nd t
he t
ype
of t
he w
ire
expr
ess
as f
ollo
w.
For
exa
mpl
e: 2
0 M
Wir
e co
lor
:20
is s
ingl
e re
dW
ire
type
: M is
AW
G2
4 U
L10
07
Wir
e C
olor
Wir
e Ty
peT
oler
ance
Uni
tem
mPr
op.
:
0~10
00
1001
~20
00
2001
~30
00
3001
~40
00
4001
~50
00
±10
±20
±30
±40
±50
Nam
e:
Cha
rtD
raw
ing
NO
.
Dat
e:
Path
:
Ver
sion
:
Pag
e
A3 14
-Sep
-201
6Z:
\Saf
ari
rang
er非洲小猎人
\英文
\2寸
GM
P版(礼品)
\配线图
V1.
0
Saf
ari R
ange
r 1P
priz
e ve
r.(D
BV
) wiri
ng d
iag
ram
22X
LRP
D-P
X-0
0
Noi
se
filt
er
PLU
G L
NE
L
NE
FUSET5A/250V Power SW
Ear
th
10P
45Q
60P H
M1 2 3J0
1 1 2 3 HF
10P
45P
60P
10P
45Q
60P H
M
11
22
33
HF
J0
3
10P
45Q
60P
21.5
" m
onit
or
Pow
er s
upp
ly
N12
VL
GN
DE
10P
45Q
60P
DO
NG
LE
R-
R+
Spe
ake
r+ -
JP
301
XH
1 21 2
C1 21 2J0
2
P
50 9050 90
50 90
DV
I po
rtH
DM
I-O
UT
BA
TT
XH
1 21 2
BA
TT
20M
90M
20M
90M
3 41 62 5
3 4 651 2
XH
J1
03
Mar
que
e L
LED
lig
htW
XX
GC
-LE
D1
.PC
B3 41 62 5
3 4 651 2 XH
J2
Mar
que
e R
LE
D l
ight
WX
XG
C-L
ED
1.P
CB
3 41 62 5
3 4 651 2 XH
J2
3 41 62 5
3 4 651 2
XH
J1
24 10 20 30 A0
24 10 20 30 A0
24 10 20 30 A0
Mar
quee
CI
Mar
quee
DI
Mar
quee
LI
GN
D
12V
24 10 20 30 A0
NL E
Coi
n
DB
V1 2 3
1 2 34 5 6
4 5 6
J1
10
2410A0
P
GN
D
12V
GN
D20A
0
Clie
nt's
re
quir
emen
t20
1
DB
V
2
A0
34
1
6
2
7
3
8 44
10 60
C41
40H
M-9
P
XH
J1
2410A0
10 60
12V
GN
D12
V
GN
D1 2 3
1 2 34
4CO
N2
VH
24A0
24A0
40P
A0P
Coi
n m
ech.
FAN
12V
/4"
1 21 2 P
J0
5 CG
ND
12V
W5
630
-LC
40c
m-6
0z/
m-D
C1
2V
20 A0
1 21 2 P
J0
4 C
20 A0
24 A0
24 A0
20 A0
20 A0
Serv
ice
btn
12V
Res
et b
tn
Test
btn
GN
D
Coi
n m
eter
Tik.
met
er1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
J1
09
P
99 10
10
Coi
n m
eter
Tik
. m
eter
GN
D
S1
S2
S3
Serv
ice
btn
Coi
n re
set
btn
Test
btn
30M
40M
50M
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 CP
J0
6
20M
A0M
20M
A0M
20M
X2
A0
A0M
X3
10 20
12V
GN
D
40P
A0P
Coi
n re
fun
dTi
k. d
rive
GN
D12
V
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
J1
08
P
90 50 24 A0
50 24 A0
903 41 2J
1
21 43
VH
3 41 2
VH
3 4
J3
1 2T
ik.
con
vert
PC
BT
ICK
-CH
.PC
B1P
tik.
dis
pens
er
HX
503
00-
4RF
3 41 2J1
21 43
30M
24 A0
30
30M
24A0
30
Doo
r S
WA
990
LED
352
8 w
hite
lig
ht s
trip
1 212
VG
ND
1 21 2
J1
0 PC
24 7024 A
0D
igit
al P
CB
lig
ht0.
55m
LED
352
8 w
hite
lig
ht s
trip
1 212
VG
ND
1 21 2
J1
1 PC
24 8024 A
0D
igit
al P
CB
lig
ht0.
55m Rec
eiv
e h
ook
sen
sor
MSh
ake
mo
tor
20M
90M
A0M
22X
HD
-DG
LED
.PC
B
Rod
res
ista
nce
Rod
lig
ht 1
Rel
ease
ho
ok b
tnR
ecei
ve
hoo
k s
enso
r
Doo
r SW
Rel
ease
ho
ok b
tn l
ight
Arm
sha
keA
rm re
sist
ance
forc
ceL
side
ligh
tR
sid
e lig
ht
GN
D
CP
1 2 3 4 5 6 7
1 2 3 4 5 6 78 9 10
8 9 1011 12 13 14 15 16
11 12 13 14 15 1617 18
17 1819 20
19 20
J1
05 1 2 3 4 5 6 7
1 2 3 4 5 6 78 9 10
8 9 1011 12 13 14 15 16
11 12 13 14 15 1617 18
17 1819 20
19 2021 22
21 22
J1
01 23 24 25 26
23 24 25 26Y
Y1
820
D-2
6P
3 41 23 41 2 P
CJ1
2
40 50 60 70 80 10 20 90 A9
91 92 A0
10 20 30 24
91 92 A0
10 20 3024
1 21 2
VH
CO
N3
GN
D5V
B0
A9
31 231 2 P
CJ1
3
Rel
ease
ho
ok b
tn
Rel
eas
e ho
ok b
tn li
ght
Indi
cato
r lig
ht24 A
040 10
24 A0
40 10
20M
90M
A0M
3 41 62 5
3 4 651 2
B0
20 A9
PC
24 50 24X
260 24
X2
J1
4
A0
31 2
24 A0
60 60 24X
2A
0X2
1 212
VG
ND
XH1 2
J1
24A0
22X
HD
-DG
LED
.PC
BR
od l
ight
21 2
12V
GN
D
XH1 2
J1
24A0
22XL
RP
D-P
X-01
22XL
RP
D-P
X-02
22XL
RP
D-P
X-03
J1
5
22XL
RP
D-P
X-04
22XL
RP
D-P
X-06
10.WIRING DIAGRAM