Panaray®
402® Series IILoudspeaker
General Description
The Bose® 402® Series II loudspeakeris a 120-Watt speaker designed forpermanent installations and portableuse in indoor and outdoor commer-cial applications. As a new additionto the Bose line of InstalledAnywhereTM loudspeakers, it meetsour strict standards for outdoor use.The 402 Series II loudspeaker offersthe following features:
• Voice and music reproduction overa broad dispersion area
• A rugged, portable enclosure withmetal grille
• Slim, aesthetic styling in black andwhite
• Weather-resistant design to ensurereliable performance indoors andoutdoors
• A full complement of brackets andstands available for a variety ofproduct uses
Each 402 Series II loudspeaker usesfour (4) 11.34cm full-range driversmounted in symmetric vertical pairson a faceted Articulated Array® baffleassembly. The drivers feature low-impedance, edge-wound aluminumvoice coils, 12-ounce Ferrite Vceramic magnets, and moldedpolyester frames. Their advancedcone and motor system gives themhigh linear excursion capability andpower output. Environmental durabil-ity is built into soft parts - cone,surround and spider - and coatedonto the hard parts of the driver.These materials optimize the InstalledAnywhereTM - performance of theloudspeaker.402 Series II loudspeakers are usedin combination with the Panaray®
system digital controller or the Bose1600 or 1800 amplifiers. They work incombination with the 402 plug-in EQcard to provide active equalizationfor the system.
The Panaray system controllerassures smooth, accurate spectral
Frequency Range90Hz to 16kHz ±3dB
Sensitivity1
91dB-SPL @ 1W, 1m (pink noise)
Maximum Acoustic Output2
111dB-SPL @ 1m (pink noise)
115dB-SPL @ 1m (IEC3 noise)
Dispersion (–6dB point, average,1-4kHz)
Horizontal 120˚Vertical 60˚
Long-Term Power Handling4
120W continuous
Impedance
8Ω nominal
Mechanical SpecificationsDimensions: 23.25"H x 8.1"W x7.25"D (59 cmH x 21 cmW x18 cmD)Weight: 15 lb (7 kg)Available colors: Black and White
Technical Information
1Full bandwidth pink noise is applied to the 402-II Speaker and amplified to a level at the loud-speaker terminals corresponding to 1 Watt as referenced to the nominal impedance. The averagesound pressure level (dB-SPL) is measured at 1 meter from the speaker in an anechoic environment.2Full bandwidth pink noise is applied to the 402-II Speaker and amplified to a level at the loud-speaker terminals corresponding to the long-term rated power handling of the speaker. The averagesound pressure level (dB-SPL) is measured at 1 meter from the speaker in an anechoic environment.3Full bandwidth pink noise, meeting International Electrotechnical Commission (IEC) Standard#268-5, with a spectrum corresponding to average program material.4Full bandwidth noise, meeting the IEC Standard #268-5 is applied to the 402-II Speaker andamplified to a level at the loudspeaker terminals corresponding to the power handling of theloudspeaker. The loudspeaker must show no visible damage or measurable loss of performanceafter 100 hours of continuous testing.
Installation
Installation and use instructions areincluded with the loudspeaker.
The 402 Series II loudspeakers aredesigned to be wall or ceilingmounted, or mounted on stands forportable use. The following versatileaccessories are available from Bose:
• WBP4 402 Wall Mount Bracket(0-45˚ pitch, ± 60˚ yaw in verticalorientation; ±28˚ in horizontalorientation) (black and white)
• SB4 402 Speaker Single FlyBracket (0-45˚ pitch) (black andwhite)
• SS-10 Speaker Stand with Mount-ing Adapter and Carry Bag (black)
• TK-402 Speaker Transit Kit (black)
Connectors: Two (2) parallel-wiredNL4 connectorsEnclosure construction: Mica-reinforced polyethylene copolymerstructural foam
The loudspeaker shall be a multipledriver, full-range system with matchedactive equalization as follows:The transducer complement shallconsist of four (4) full-range environ-mental drivers of 11.4 cmdiameter, mounted vertically in afaceted baffle. Each driver shall havea rated impedance of 1.6Ω and shallbe wired in series, resulting in acomposite speaker assembly nominalimpedance of 8Ω.
The loudspeaker system sensitivityshall be 99dB-SPL in the 300Hz to3kHz range and 91dB-SPL in the90Hz to 16kHz range with bothmeasurements referenced to a 1 Watt(2.83V) pink noise input at 1 meter.The nominal horizontal beamwidthshall be 120 degrees, and the nominalvertical beamwidth shall be 60 de-grees. The power handling capacity ofthe loudspeaker shall be 120 Wattscontinuous pink noise, band-limitedfrom 90Hz to 16kHz.
The loudspeaker shall be providedwith a ducted vent system, tuned at95Hz. The input connectors of the402® Series II loudspeaker shall consistof two parallel Speakon® NL4 recep-tacles.
The enclosure of the 402 Series IIloudspeaker shall be composed ofmica-reinforced polyethylene copolymerstructural foam. Its outer dimensionsshall be 23.25"H x 8.1"W x 7.25"D (59cmH x 21 cmW x 18 cmD); its weightshall be 15 lb (7 kg).The loudspeaker shall be the Bose®
402 Series II loudspeaker system.
System Configurations
Mixer/Preamp
Bose controller
Power amplifier
402 EQ
402
CH1
CH2
CH2
CH1
CH1 CH2
402
CH2CH1
Mixer/Preamp
Bose® power amplifier
402
(402)
CH2CH1
CH1 CH2
402
(402)
CH1 CH2
(402) (402)
Speaker
Speaker Speaker
Speaker
Engineers’ andArchitects’ Specifications
Loudspeaker Configuration
The Bose 402 Series II loudspeaker canbe used with the Bose 1600 and 1800amplifiers. It is also compatible withindustry standard amplifiers rated for 4-8Ω loads.
The 402 -II speaker is packaged one percarton.
The Panaray System digital controllershall provide active electronic equal-ization and crossover functions.
response across the entire operatingrange of the 402 Series II loudspeaker.Using a controller or EQ card alsoallows for crossover of the 402-IIloudspeaker with a Bose bass loud-speaker.
Speaker Views
Side View
Top View
Rear View
Bottom View
Safety and RegulatoryCompliance
All versions of the Bose 402-IIloudspeakers comply with ANSI/EIA636, Recommended LoudspeakerSafety Practices and EMC Directive89/336/EEC and Article 10 (1) of theDirective in compliance withEN50081-1, EN50082-1, as signifiedby the CE mark.
All versions of the Bose 402-II loud-speaker are covered by a 5-year,transferable limited warranty.
Warranty Information
The loudspeaker system shall be usedwith a Panaray System Digital Control-ler, to be connected beforethe input(s) of the system poweramplifier(s), or with a 402 EQ card, tobe installed in a Bose 1600 or 1800amplifier.
©2001 Bose Corporation, The MountainFramingham, MA 01701-9168259456 AM Rev.02 PC028700 JN10808