Download - Operators Instructions Boomer 281-DC10
-
Atlas CopcoBoomer 281 with carrier DC10Operators instructionsPM No. 9852 1454 01b
2005-12
-
Atlas Copco Rock Drills ABSE-70191 rebro, Sweden
SAFETY INSTRUCTIONS
Before starting, read all instructions carefully.
Special attention must be paidto information alongsidethis symbol.
Only use genuine Atlas Copco parts.
1250 0071 04
Copyright 2005, Atlas Copco Rock Drills AB, SwedenAny unauthorized use or copying of the contents or any part thereof is prohibited.This applies in particular to trademarks, model denominations, part numbers and drawings.
-
SafetySafetyReference................................................................................................................. 53
-
Safety 4
-
SafetyReferenceNoteAlways read the information under Safety before starting to use the rig or starting maintenance work.
1250 0099 895
-
Safety 6
-
Operators instructionsOperators instructions1. Technical data......................................................................................................... 11
Boomer/Rocket Boomer 280 with DC10 carrier................................................... 11Data plate............................................................................................................... 11
Data plate contents............................................................................................ 11Location of data plate ....................................................................................... 12
2. Component locations.............................................................................................. 13Main rig components............................................................................................. 13
3. Application............................................................................................................. 14General .................................................................................................................. 14
4. Daily inspection ..................................................................................................... 15General .................................................................................................................. 15Checklist ................................................................................................................ 15Daily maintenance ................................................................................................. 15Freeze prevention measures .................................................................................. 16
5. Controls .................................................................................................................. 17Locations ............................................................................................................... 17Description of operation ........................................................................................ 18
Control panel .................................................................................................... 18Control panel functions..................................................................................... 18Drill panel ......................................................................................................... 21Drill panel functions ......................................................................................... 21Positioning panel .............................................................................................. 22Positioning panel functions............................................................................... 23Lever for protective roof, jacks and reeling units............................................. 23Dual command for reeling units, option ........................................................... 24
6. Electrical system .................................................................................................... 25Electric cabinet ...................................................................................................... 25Resetting emergency stop...................................................................................... 26
7. Repositioning ......................................................................................................... 28Environment .......................................................................................................... 28Before starting the diesel engine ........................................................................... 28Starting the diesel engine....................................................................................... 31Before tramming.................................................................................................... 31Checking the brakes .............................................................................................. 32
Checking the parking brake .............................................................................. 32Checking the service brakes ............................................................................. 32Checking the interlock circuit........................................................................... 32
Repositioning......................................................................................................... 34Safety ................................................................................................................ 347
-
Operators instructions Parking................................................................................................................... 35Operating the boom, jacks, protective roof and reeling units................................ 36
Control levers.................................................................................................... 36Boom................................................................................................................. 37Jacks.................................................................................................................. 37Protective roof................................................................................................... 37Cable reeling unit (option) ................................................................................ 37
Unwinding the cable .................................................................................... 38Reeling in the cable...................................................................................... 38
8. Positioning.............................................................................................................. 39Positioning equipment ........................................................................................... 39Positioning panel ................................................................................................... 40Operating ............................................................................................................... 41
Safety ................................................................................................................ 41Diesel operation ................................................................................................ 41Raising and slewing the boom .......................................................................... 41Slewing and inclining the feeder ...................................................................... 42Feed lookout cylinder and boom telescope....................................................... 43Rotation and feed extension.............................................................................. 44Transport position ............................................................................................. 45Bench drilling ................................................................................................... 46Cross-cut drilling .............................................................................................. 46Roof drilling...................................................................................................... 47
9. Drilling ................................................................................................................... 48Environment .......................................................................................................... 48Before drilling........................................................................................................ 48
Connect to power supply .................................................................................. 48Battery .......................................................................................................... 48Mains power................................................................................................. 49
Connect to water supply ................................................................................... 49Connect the air supply ...................................................................................... 50Checks............................................................................................................... 50Setting up the rig............................................................................................... 50
Drilling................................................................................................................... 51Drilling levers ................................................................................................... 51Collaring and full drilling ................................................................................. 51Cease drilling .................................................................................................... 52In the event of drill jam..................................................................................... 52Air blowing of drilled hole, option ................................................................... 53Changing drill bit .............................................................................................. 53
Safety............................................................................................................ 53Changing drill bit against rock face ............................................................. 53Changing drill bit in bottom of hole............................................................. 54
Check when drilling.......................................................................................... 55Safety............................................................................................................ 55Rock drill...................................................................................................... 558
-
Operators instructionsSystem.......................................................................................................... 55Hoses and couplings..................................................................................... 56
Settings ............................................................................................................. 56Setting feed pressure .................................................................................... 56Feed pressure for collaring........................................................................... 57Feed pressure for full drilling....................................................................... 57Feed pressure for full drilling of reaming holes, option .............................. 57Introduction.................................................................................................. 58Max. feed pressure (upper and lower cylinder) ........................................... 59Pressure difference between upper and lower cylinder ............................... 59Feed pressure for collaring and full drilling................................................. 60Feed pressure, reverse .................................................................................. 60Description ................................................................................................... 61RPCF feed control........................................................................................ 61Feed (rock drill) return movement ............................................................... 62Setting the anti-jamming protection............................................................. 62Setting the feed return movement ................................................................ 62Setting RPCF during drilling ....................................................................... 63
After drilling.......................................................................................................... 64Safety ................................................................................................................ 64Freeze prevention measures.............................................................................. 64
10. Extension drilling ................................................................................................. 65Equipment for extension drilling........................................................................... 65Operator panel ....................................................................................................... 66Operating ............................................................................................................... 67
Safety ................................................................................................................ 67Manual rod adding............................................................................................ 67
Preparation ................................................................................................... 67Drilling and extension.................................................................................. 68Removing drilling rods ................................................................................ 69
11. Directional control................................................................................................ 70FAM....................................................................................................................... 70Control panel ......................................................................................................... 70Operating ............................................................................................................... 71
Start ................................................................................................................... 71Menus ............................................................................................................... 72
Main menu ................................................................................................... 72Menu tree, branch 1 ..................................................................................... 73Menu tree, branch 2 ..................................................................................... 73Menu tree, branch 3 ..................................................................................... 75Menu tree, branch 4 ..................................................................................... 76Menu tree, branch 5 ..................................................................................... 77Menu tree, branch 6 ..................................................................................... 78
Working menu ....................................................................................................... 79Maximum hole depth............................................................................................. 80Reference direction................................................................................................ 809
-
Operators instructions Rig..................................................................................................................... 80Tunnel ............................................................................................................... 82
Hole depth.............................................................................................................. 83Fault indication ...................................................................................................... 83
12. Shift control, option.............................................................................................. 85APC 50 (Automatic Powershift Control................................................................ 85
Description of operation ................................................................................... 85Control panel..................................................................................................... 86
Display of current gear and direction of travel ............................................ 87Display of turbine shaft speed...................................................................... 88Display of tramming speed .......................................................................... 89Display of fault codes................................................................................... 8910
-
Operators instructions1. Technical data1. Technical data
Boomer/Rocket Boomer 280 with DC10 carrierNoteA brief summary of data follows. For more detailed information, see the maintenance instructions. All information applies to a standard-equipped rig.
Length, rig in transport position 8.6-11.0 mWidth 1.65 mHeight, rig with protective roof 2.1-2.8 mWeight 10-14 tonnesInstalled diesel engine power 42 kWInstalled electric power capacity See data plateVoltage See data plateFrequency See data plateMax. lateral inclination 0Max. longitudinal inclination. 14Stability Complies with CENAmbient temperature 0 to +40CNoise level at operator's station (ISO/DIS 11201) 114 dB(A) re2 Radiated acoustic power (ISO/DIS 11201) 124 dB(A) re1 pWVibration level, floor (ISO 2631/1) 0,10 m/s 2
Data plate
Data plate contentsThe rig carries a data plate which contains the following data:
Product name Product type Serial number Installed diesel engine power Installed electric power capacity Rated voltage Rated frequency Gross weight
The data plate also indicates whether the rig is CE certified.11
-
Operators instructions 1. Technical dataLocation of data plate
Figure: Location of data plate12
-
Operators instructions2. Component locations2. Component locations
Main rig components
Figure: Boomer/Rocket Boomer with DC10 or DC11 carrier1 Rock drill2 Feeder3 Boom4 Front jacks5 Rear jacks6 Cable reeling unit7 Protective roof
1 2
3
45
6
1250 0072 12
713
-
Operators instructions 3. Application3. Application
GeneralThe drilling equipment is designed exclusively for drilling holes in tunnels and mines. All other uses are considered to be inappropriate.
Examples of inappropriate use:
Lifting and transporting loads and people Supporting objects Scaling rock
The manufacturer is not liable for damage caused by inappropriate use.
It is essential the operator has read and comprehends the operator, maintenance and repair manuals as well as the maintenance schedules.
The drilling equipment must only be used, maintained and repaired by personnel well conversant with the equipment and the dangers involved.
It is essential that personnel observe general and local safety, health and traffic regulations.
The manufacturer is not liable to damage caused by any arbitrary changes made to the drilling equipment.14
-
Operators instructions4. Daily inspection4. Daily inspection
GeneralNoteTo ensure optimal utilisation of the rig and its equipment, it is of utmost importance that daily maintenance is carried out in accordance with our recommendations.
The objective for the daily inspection of the rig is to:
detect faults at an early stage facilitate servicing allow scheduled maintenance and planned reconditioning work to be performed prevent costly secondary damage prevent breakdowns prevent personal injury
NoteDo not operate the rig or the rig equipment until all faults have been rectified.
ChecklistNoteAs soon as a fault is detected, note it and report to maintenance personnel.
Always begin by making an inspection round. Check safety devices Check hoses and cables Check oil levels Check the lubrication points. Keep your eyes open for possible leakage and wear. Pay attention to any faults in the function of the controls.
Daily maintenance Rinse off the rig with water, especially the feeder and other parts that have been
exposed to drill cuttings or rock debris See maintenance schedule for each component.15
-
Operators instructions 4. Daily inspectionFreeze prevention measures Draining the water system, see maintenance instructions, Water system: Freeze
prevention measures. Draining the air tank, (option), see maintenance instructions, Air system: Freeze
prevention measures. Draining the scrubber (option), see maintenance instructions, Exhaust filtering:
Scrubber; Freeze prevention measures. Draining of Swellex pump (option), see maintenance instructions, for Swellex
pump: Freeze prevention measures. 16
-
Operators instructions5. Controls5. Controls
Locations
Figure: Location of controls, DC10 carrierA Operator's area with control panelB Brake pedalC AcceleratorD Levers for operating jacksE Levers for diesel positioningF Levers for operating protective roofG Drilling and positioning panel
1250
014
1 59
2
46
8
12
1416
bar
10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
2
46 8
1214
16bar
10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
D
C
B
A
G
E F17
-
Operators instructions 5. ControlsDescription of operation
Control panel
Figure: Control panel
Control panel functions
Table: Control panel functions
Designation Function DescriptionH11 Indicator lamp for parking brake The lamp shines if the parking brake is applied.
H12 Indicator lamp for transmission The lamp shines if the transmission fluid pressure is too low or if its temperature is too high. The parking brake is also applied. Contact maintenance personnel.
H13 Indicator lamp for suction filter Indicates that the suction filter in the hydraulic oil tank is clogged. If the lamp shines, the filter must be changed. Contact maintenance personnel. The lamp may light for a short time when the hydraulic oil is cold.
H14 Indicator lamp for hydraulic oil level
This lamp shines if the level of fluid in the hydraulic oil tank is too low. The hydraulic oil must be topped up immediately.
N 122
1
P
P
0 4/4
30
40
6050
20
10
H11 H12 H13 H14 H15 H16 H17 H18
P1 P2
H20
T10T5
T7 T8
T2T4 T3
T12
1250
011
6 14
1250
011
6 15
1250
011
6 16
1250
011
6 1718
-
Operators instructions5. ControlsH15 Indicator lamp for fan belt This lamp shines if the fan belt breaks. The belt must be replaced immediately. Contact maintenance personnel.
H16 Indicator lamp for diesel engine lubricating oil pressure
This lamp shines if the pressure is too low. If this occurs, the engine must be switched off immediately and the cause rectified by maintenance personnel.
H17 Indicator lamps for engine temperature
This lamp comes on if the temperature is too high. The engine must be switched off immediately and maintenance personnel contacted if the lamp comes on during operation.
H18 Indicator lamp for battery charging
Under normal driving conditions, the lamp should be out to indicate the batteries are charging. The lamp is on when the ignition is on. Contact maintenance personnel if the lamp comes on while driving.
H20 Preheating indicator
T2 Ignition switch
T3 Button for differential lock The differential lock is activated when the button is depressed.
T4 Button for parking brake The brake is applied when the button is depressed and released when the button is extended. The parking brake must be applied for the diesel engine to be started.
T5 Switch for roof-mounted lighting
T7 Switch for lighting on carrier
Designation Function Description12
50 0
116
1812
50 0
116
1912
50 0
116
2012
50 0
116
2112
50 0
116
2212
50 0
116
2312
50 0
116
2412
50 0
116
2512
50 0
116
2612
50 0
116
2719
-
Operators instructions 5. ControlsT8 Button for lamp test When the button is depressed, all indicator lamps should light simultaneously. If an indicator lamp does not work, this should be changed immediately.
T10 Gear selector The gear selector must be in neutral (N) for the diesel engine to be started.
T12 Horn button
P1 Hour counter for diesel engine Shows the diesel engine's operating hours
P2 Tank meter Shows the level of fuel in the diesel tank
Designation Function Description
1250
011
6 28
1250
011
6 29
1250
011
6 30
1250
011
6 31
1250
011
6 3220
-
Operators instructions5. ControlsDrill panel
Figure: Drill panel
Drill panel functions
Table: Drill panel functions
Designation FunctionS106 Button for stopping hydraulic pumpS105 Button for starting hydraulic pumpLr Rotation leverLh Percussion leverLf Feed lever
2
46 8
1214
16bar
10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
2
46 8
1214
16bar
10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
S106
S105
Lr Lh Lf
VflVfh
Gr
Gh
Gf
Gl
Blb
Law
Ga GwGrfGdp
V1aV1b
LrnLdsLtf
Lrb
V6
1250 0141 9021
-
Operators instructions 5. ControlsPositioning panel
Figure: Positioning panel
Vfl Valve for feed pressure, collaringVfh Valve for feed pressure, full drillingGr Rotation pressure gaugeGh Percussion pressure gaugeGf Feed pressure gaugeGl Lubricating oil pressure gaugeGdp Pressure gauge for damper pressure (DCS 18
only)Ga Air pressure gaugeGrf Pressure gauge for blocked return oil filter in
hydraulic oil reservoir (DCS 18 only)Gw Water pressure gaugeBlb Button for removing the drill bit (DCS 18 only)Law Water flushing leverLrb Small hole - reaming hole selector leverV6 Pressure control valveV1a RPCF valve, standardV1b RPCF valve for reaming hole, optionLtf Feed lever for threading and unthreading rodsLds Lever to open/close front drill-steel support BSH
110Lrn Single-rod/extension drilling selector lever
Designation Function
1250 0130 77
Lfr LflLbe
Lfe
Bap
Lbc22
-
Operators instructions5. ControlsPositioning panel functions
Table: Positioning panel functions
Lever for protective roof, jacks and reeling units
Figure: Levers for diesel positioning
Table: Levers for diesel positioning
No. FunctionLfr Lever for feed rotationLfl Lever for feed lookoutLbe Lever for boom telescopeLfe Lever for feed extensionBap Anti-parallel buttonLbc Lever for boom positioning
LEVER FUNCTIONP Lever for selecting
Boom positioning Neutral
K Operating the cable reeling unitT1 Protective roof up/down (one of two
cylinders)
1250 0068 30
2 46
8
121416
bar 10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
2 46
8
121416
bar 10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40ba
r
10
D1D2D3D4D5
T2
T1
P
K23
-
Operators instructions 5. ControlsDual command for reeling units, optionNoteSet the positioning lever to the positioning point (activate diesel positioning).
Figure: Dual command for reeling units
Table: Dual command for reeling units
T2 Protective roof up/down (one of two cylinders)
D5 Jack, front left, up/downD4 Jack, front left, in/out D3 Jacks, rear, up/downD2 Jack, front right, in/outD1 Jack, front right, up/down
LEVER FUNCTION1 Operating the cable reeling unit2 Operating the water hose reeling unit
LEVER FUNCTION
1250 0151 39
1 224
-
Operators instructions6. Electrical system6. Electrical system
Electric cabinet
Figure: Electric cabinet
Table: Electric cabinet functions
SymbolDesignation Function DescriptionH65 Indicator lamp Motor overload
The lamp comes on if the motor is overloaded
H35 Indicator lamp Phase sequence fault The lamp comes on if a phase sequence
fault occurs
Q7
S32
H53H36H39 H65H35
1250
0136
11
1250 0059 49
1250 0059 9725
-
Operators instructions 6. Electrical systemResetting emergency stop1. Pull out the emergency stop that has been activated.
2. Switch on the electrical cubical by turning the main switch (Q7) to position 0 and then to 1.
H36 Indicator lamp Low hydraulic oil pressure The lamp comes on if the oil level is too
low
H39 Indicator lamp Return oil filter The lamp comes on if the return oil filter
is clogged
H38 Indicator lamp High hydraulic oil temperature The lamp comes on if the oil temperature
is too high
H53 Indicator lamp Main power The lamp comes on when the main
power is on.
S32 Button Lamp test All lamps in the electric cabinet should
come on when this button is pressed
Q7 Switch Main switch
S51 Switch Motor switch, motor 1 Must be in position (1) when in operation In position (0) the control voltage will be
cut off.S52 Switch Motor switch, motor 2, 2-boom rigs only
Must be in position (1) when in operation In position (0) the control voltage will be
cut off.
SymbolDesignation Function Description
1250 0059 48
1250 0065 15
C
1250 0059 96
1250 0059 46
1250 0059 47
0
= 1
= 0
1
1250 0060 01
1
1250 0059 98
2
1250 0059 9926
-
Operators instructions6. Electrical system3. Check that the indicator lamps on the electric cabinet work by pressing the lamp test button (S32).27
-
Operators instructions 7. Repositioning7. Repositioning
Environment
Before starting the diesel engine
N.B.It is important that the daily inspection checkpoints have been carried out to ensure that the equipment is in good condition.
1. Check the engine oil level. Top up as necessary.
Figure: Oil level
ENVIRONMENTAL DIRECTIONS
Think of the environment! Exhaust gases are poisonous and
environmentally hazardous. Good ventilation is essential when the
diesel engine is running. Well-maintained air filters help to keep
down emission levels.
1250 0068 2828
-
Operators instructions7. Repositioning2. Turn the battery switch to position (1).
Figure: Battery switch
3. Check the fuel level on the gauge on the control panel.
4. Check the hydraulic oil level in the level glass on the hydraulic reservoir. Top up as necessary, see maintenance instructions, Hydraulic system: Changing oil.
0
1
1250 0013 3429
-
Operators instructions 7. Repositioning5. On rigs with scrubber: check the water level in the scrubber and top up if neces-sary.
Figure: Water inlet
Figure: Scrubber
Filling up the scrubber:
a. Make sure stopcock (1) is closed and stopcock (3) is open.
b. Connect a water supply to (4).
NoteIf the rig has a water hose reeling unit, this is connected to (4). Connect the water to the reeling unit.
c. Open the level cock (A) on the scrubber.
d. Open the filler cock (E) until water flows out of the level cock (A).
e. Close the filler cock (E) and level cock (A).
4
3
2
1
5
1250 0137 14
612
50 0
146
21
F
D
A
C
B
E30
-
Operators instructions7. Repositioningf. Depressurise the hose by opening cock (1) and closing cock (3).
g. Disconnect the water from (4).
h. Close cock (1).
Starting the diesel engineAll emergency stops must be pulled out and the parking brake applied. Gear selector must be in the neutral position. Check also that the diesel engine stop is depressed.
1. Press the lamp test button to check that all warning lamps in the panel light up.
2. Preheat the diesel engine if it is cold by turning the ignition key to position (1). The preheating indicator shows when the glow plugs are sufficiently warm.
3. Start the diesel engine by turning the ignition key to position (2). Release the key as soon as the engine has started.
4. Check that the warning lamps go out. The parking brake indicator lamp goes out when the parking brake is released.
5. If any of the warning lamps do not go out or if the engine will not start, check the fuses inside the control panel and the main fuse by the battery switch.
Figure: Fuses in the control panel
Before tramming1. Check that the booms are positioned so that they do not obstruct vision or hinder
tramming the chassis, see operator's instructions, Positioning.
2. Check that the jacks are retracted.
3. Turn on the headlamps.
4. Make sure that nobody is standing in the rig's direction of travel.
1250 0068 2731
-
Operators instructions 7. RepositioningChecking the brakesChecking the parking brake
1. Make sure that the parking brake is applied.
2. Start the engine and engage 2nd gear.
3. Gradually increase engine rpm to maximum.
4. Check the rig for movement. If the rig moves the brakes must be adjusted without delay.
NoteDo not continue this check for longer than 4 seconds at most.
Checking the service brakes1. Start the diesel engine.
2. Depress the brake pedal and hold it down.
3. Release the parking brake.
4. Engage 2nd gear.
5. Gradually increase engine rpm to maximum.
6. Rigs with DC10 carrier have self-adjusting service brakes. If the rig moves during inspection, this indicates that the brake discs require changing.
NoteDo not continue this check for longer than 4 seconds at most.
Checking the interlock circuitThe rig has an interlock circuit, which applies the parking brake if any of the follow-ing should happen:
Engine oil pressure falls below a certain value. Transmission oil pressure falls below a value. The hydraulic oil pressure in one of the brake circuits falls below a certain value. The limit switch for the cable reeling unit is activated (option).
The rig is equipped with a test button for checking the interlock circuit.32
-
Operators instructions7. RepositioningFigure: Location of interlock circuit test button
Check the interlock circuit as follows:
1. Depress the brake pedal and hold it down.
2. Release the parking brake.
3. Press the test button.
4. Check that the parking brake has been applied.
5. Reset the interlock circuit by applying and then releasing the parking brake.
1250
010
1 3533
-
Operators instructions 7. RepositioningRepositioningSafety
1. Select the direction of travel and gear with the gear selector.
NoteSelect a gear based on the driving conditions.Up and downshifts can be made while travelling if the diesel engine speed is adapted accordingly.
2. Release the parking brake.
3. Depress the accelerator and adjust your speed to the terrain.
4. Check the warning lamps while driving. It is essential that faults are detected early on so that consequential damage is avoided. Report faults to maintenance person-nel.
NoteFor rigs equipped with APC 50 gear monitor (option), see operator's instructions, Gear monitor.
WARNING Tipping risk. May cause serious personal injury. The gear selector must never be moved
to neutral position when tramming uphill or downhill.
Always turn the rig on level ground. The boom must never be swung out more
than necessary during operation. Do not swing out the booms to the side
during tramming on cambers or sloping track.
The boom and feeder must always be positioned back at transport position if they have been temporarily swung out for narrow passageways.
The cab must be fully lowered on rigs equipped with cab lift.34
-
Operators instructions7. RepositioningParking1. Apply the parking brake.
2. Move the selector lever to neutral position.
3. Lower the jacks until the wheels are clear of the ground.
4. Switch off the diesel engine by pulling out the stop control.
NoteThe diesel engine must only be stopped with the stop control. Using the ignition key can damage the rig's electrical system.
5. Switch off the headlights.
6. Switch off the ignition with the ignition key.
7. Turn off the power supply to the chassis with the battery switch.
NoteIn case of risk of freezing see operator's instructions, Daily inspection: Freeze pre-vention measures. 35
-
Operators instructions 7. RepositioningOperating the boom, jacks, protective roof and reeling units
Control levers
Figure: Levers for diesel positioning
Table: Levers for diesel positioning
LEVER FUNCTIONP Lever for selecting
Boom positioning Neutral
K Operating the cable reeling unitT1 Protective roof up/down (one of two
cylinders)T2 Protective roof up/down (one of two
cylinders)D5 Jack, front left, up/downD4 Jack, front left, in/out D3 Jacks, rear, up/downD2 Jack, front right, in/outD1 Jack, front right, up/down
1250 0068 30
2 46
8
121416
bar 10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40bar
10
2 46
8
121416
bar 10
0
20
30
40bar
10
0
20
30
40bar
10
0
20
30
40ba
r
10
D1D2D3D4D5
T2
T1
P
K36
-
Operators instructions7. RepositioningBoom1. Set the positioning lever to the positioning point.
2. Operate the boom with the boom levers on the operator panel, see operator's instructions, Positioning.
3. After positioning the boom the positioning lever must be reset to the neutral posi-tion.
Jacks1. Set the positioning lever to the positioning point.
2. The front jacks are moved sideways with lever (D2) and (D4).
3. The front jacks are raised and lowered with lever (D1) and (D5).
4. The rear jacks are raised and lowered with lever (D3).
5. After manoeuvring the jack, the positioning lever must be reset to neutral position.
Protective roof1. Set the positioning lever to the positioning point.
2. Manoeuvre the roof up or down with the lever for the protective roof.
3. After manoeuvring the protective roof, the positioning lever must be reset to neu-tral position.
Cable reeling unit (option)
CAUTION High voltage cable. Incorrect handling may cause serious
personal injury. Before tramming the rig again it is VITAL
that the gear selector is in Reverse position, otherwise the cable is pulled from its mounting.37
-
Operators instructions 7. RepositioningUnwinding the cable1. Check that the electric cable is firmly secured to the wall.
2. Run the rig forwards. The cable will unreel through slipping of the cable reeling unit's clutch.
The cable can also be run out manually:
a. Set the positioning lever to the positioning mode.
b. Set the lever for the cable reeling unit to the out position.
NoteBear in mind that the cable can easily become tangled.
c. Set the lever for the cable reeling unit to neutral position.
d. Set the lever for positioning to neutral position.
3. If the cable reeling unit has the optional limit switch kit, the parking brake can be applied and the engine switched off when the cable is unreeled. The purpose of the limit switch is to prevent damage to the cable. An indicator lamp comes on when there are three turns of cable left on the cable drum. When there is one turn left, the parking brake is applied and the diesel engine stopped.
Reeling in the cable1. Check that the cable is properly secured.
2. Set the positioning lever to the positioning mode.
3. Set the lever for the cable reeling unit to in position.
4. Reverse the rig and the cable is wound up on the cable reeling unit.
5. Stop the rig when there is a little cable left.
6. Set the lever for the cable reeling unit to neutral position.
7. Set the lever for positioning to neutral position.
8. For better control, wind up the last section using the dual command on the back of the rig. This only works if the rig is equipped with the dual command option for the cable reeling unit.38
-
Operators instructions8. Positioning8. Positioning
Positioning equipment
Figure: Boom, feeder and rock drill1 Rear boom cylinders2 Telescopic unit3 Feed extension cylinder4 Front boom cylinders5 Rotary actuator6 Feed lookout cylinder
12
3 4 5
6
1250 0076 0339
-
Operators instructions 8. PositioningPositioning panel
Figure: Positioning panelLfr Lever for feed rotationLfl Lever for feed lookoutLbe Lever for boom telescopeLfe Lever for feed extensionBap Anti-parallel buttonLbc Lever for boom positioning
The control levers are direct-acting. The boom has hydraulic parallel holding of the feeder, which means that all the holes can be drilled parallel to each other. Each cyl-inder is marked using a colour coded system where the colour of the cylinder corre-sponds with the colour marking on the lever that controls it. This simplifies learning and makes it easier to directly select the correct direction for each lever. The speed of the cylinders is proportional to the travel of the levers, which makes controlling the boom smooth and adaptive.
1250 0130 77
Lfr LflLbe
Lfe
Bap
Lbc40
-
Operators instructions8. PositioningOperating
Safety
Diesel operationNoteFor diesel operation, see operator's instructions, Repositioning: Operating.
Raising and slewing the boomThe control lever for boom positioning (Lbc) is used to raise and slew the boom. The button for anti-parallel holding (Bap) should not be activated.
Figure: Control lever for boom positioning (Lbc) and anti-parallel button (Bap)
NoteTo drill parallel holes, the feeder must be horizontal (feed lookout cylinder fully retracted).
CAUTION Moving parts. Danger of serious personal injury. Make sure that no personnel are inside
the working area of the boom before the boom is operated.
Make sure that the rig is raised on the jacks.41
-
Operators instructions 8. PositioningFigure: Raising and slewing the boom
Slewing and inclining the feederThe control lever for boom positioning (Lbc) is used to slew and angle the boom. The anti-parallel button (Bap) should be depressed and held during lever movements.
Figure: Control lever for boom positioning (Lbc) and anti-parallel button (Bap)
1250 0065 1942
-
Operators instructions8. PositioningFigure: Slewing and inclining the feeder
Feed lookout cylinder and boom telescope
Figure: Section of operator panel
Control lever (Lfl) is used to operate the feed lookout cylinder and control lever (Lbe) is used to operate the boom telescope.
1250 0130 20
1250 0070 52
LfrLflLbeLfe43
-
Operators instructions 8. PositioningFigure: Feed lookout cylinder and boom telescope
Rotation and feed extension
Figure: Section of operator panel
Control lever (Lfr) is used to rotate the feeder and control lever (Lfe) to extend the feeder.
Feed extension is used to bring the feeder up to the rock face.
1250 0070 52
LfrLflLbeLfe44
-
Operators instructions8. PositioningFigure: Feeder rotation and feed extension
Transport position
Figure: Feeder and boom position before transport
1. Manoeuvre the rock drill to its rear end position on the feeder. See operator's instructions, Drilling.
2. Manoeuvre the feeder to its rear end position on the feed extension cylinder.
3. Rotate the feeder in accordance with the figure above.
1250
003
4 3845
-
Operators instructions 8. PositioningBench drilling
Figure: Bench drilling
1. Rotate the feeder 180.2. Tilt the feeder to vertical position.
3. Align the boom.
4. Position with the boom telescope cylinder.
Cross-cut drilling
Figure: Cross-cut drilling
1. Rotate the feeder 90.2. Tilt the feeder 90.3. Lift or lower the boom to a suitable position.
4. Position with the boom telescope cylinder.46
-
Operators instructions8. PositioningRoof drilling
Figure: Roof drilling
1. Tilt the feeder to vertical position.
2. Rotate the feeder 90.3. Align the boom.
4. Position with the boom telescope cylinder.47
-
Operators instructions 9. Drilling9. Drilling
Environment
Before drilling
Connect to power supply
Battery1. Turn on the power to the rig by moving the battery switch to on.
Figure: Battery switch
NoteThe battery switch must be on or the electric cabinet's indicator lamp for low oil level will light.
ENVIRONMENTAL DIRECTIONS
Think of the environment! Rock dust can be hazardous to health. Use dust binding equipment.
0
1
1250 0013 3448
-
Operators instructions9. DrillingMains power1. Check that the voltage of the outlet is correct for the rig.
2. Connect the rig to the mains power:
a. Connect the mains lead to the mains power.
b. Make sure the mains lead is firmly attached to the wall.
3. Turn on the electric cabinet:
a. Turn the main switch on the electric cabinet (Q7) to position (1).
b. Make sure the voltage indicator lamp on the electric cabinet comes on.
c. Check that the indicator lamps on the electric cabinet work by pressing the lamp test button (S32).
NoteIf any of the indicator lamps on the electric cabinet do not come on, the cause must be investigated.
4. Turn the electric cabinet switches (S51) and (S52) to position (1).
NoteSwitch position (0) is for fault finding and repair, while position (1) is for opera-tive mode.
Connect to water supply1. Make sure the water hose is clean. Blow it free from cuttings and mud if neces-
sary.
2. Connect the water hose to the water inlet (4).
Figure: Water inlet
4
3
2
1
5
1250 0137 14
649
-
Operators instructions 9. DrillingConnect the air supplyThis procedure applies when the rig is adapted for the use of an external air supply network at the worksite.
1. Connect the air supply to the rig's air intake (4).
Figure: Rig air intake
Checks1. Check the oil level in the hydraulic oil reservoir and top up as necessary. See
maintenance instructions, Hydraulic systems: Changing oil.
2. Check the oil level in the lubricating oil tank and top up as necessary.
Setting up the rigWith each new setting-up of the rig it is essential that it is correctly aligned. See Safety, Rig stability.
1. Manoeuvre the rig to the where drilling is to take place. Position it at right angles to the centre of the tunnel face, parallel to the direction of drilling. It must be pos-sible to manoeuvre the booms past the parts of the rock face that protrude the most.
2. Set up the rig on its jacks. Start with the front jacks and then the rear jacks until the rig is level (observe the spirit level in the cab).
NoteThe following points are important to observe: The rig must be raised so that none of the wheels is in contact with the ground. The rig must be standing steadily while drilling to avoid disturbing the naviga-
tion.
1250 0054 55 2
1
3
4
550
-
Operators instructions9. Drilling3. Adjust the direction of each boom as specified by the surveyor. See operator's instructions, Positioning.
4. The rig is now ready for drilling.
Drilling
Drilling leversThe various procedures are described later in this manual.
Figure: Different positions of drilling levers1 Rotation control lever2 Percussion control lever3 Feed control lever
Table: Drilling lever functions in various positions
Collaring and full drilling1. Make sure the drill levers are in neutral.
Position Function1 A Rotation right1 B Neutral1 C Rotation left2 A Neutral2 B Collaring2 C Full drilling3 A Reverse feed3 B Neutral3 C Feed forward
1250 0059 41
A B C
1
2
3
A B C
A B C51
-
Operators instructions 9. Drilling2. Start the hydraulic pump with start button (S105).
3. Make sure that the selector lever (Lrb) for small/reaming holes is in the desired position. Option.
4. Position the boom and feeder for drilling and apply the feeder dowel firmly against the rock. See operator instructions, Boom handling.
5. Start water flushing with lever (Law). Make sure the valve is fully open.
6. Start rotation drilling (rotation left) by moving the lever (Lr) forward.
7. Collaring: Start low percussion pressure by moving lever (Lh) to the centre posi-tion. At the same time, start forward feed by moving lever (Lf) forward. A low feed force is automatically attained.
8. Full drilling: Start high percussion pressure by moving lever (Lh) to its foremost position once the drill bit has entered the rock. A high feed force is automatically selected.
9. Once a hole is drilled, the percussion unit is automatically switched off and reverse feed is automatically engaged. When the rock drill has reached its rear end position, move the rotation lever (Lr) and feed lever (Lf) to their neutral positions.
10. Switch off water flushing with lever (Law).
11. Repeat steps 4 to 10 above for the next hole.
Cease drillingStop the drilling by moving the drilling levers to neutral position.
In the event of drill jamOn rock drills equipped with extraction unit (COP 1838 MEX) this must be started as follows:
1. Activate feed reverse by moving the feed lever (Lf) backwards.
2. Start collaring by setting the percussion lever (Lh) in collaring position.
Important points to consider when using the extraction unit.
The extraction unit must not be used as an aid for example - To drill with inadequate flushing agent. - To drill with such a feed force etc. that there is a risk of repeated drill jams
(applies in particular with poor rock conditions).52
-
Operators instructions9. Drilling When using the release function, the front section of the rock drill heats up rap-idly. For this reason, use the extraction unit for short periods, max. 30 seconds, and then allow the rock drill to cool down for at least 30 seconds as follows - Active feed reverse, so that the oil can circulate through the extraction unit.- If possible, activate flushing in order to cool the front section of the rock drill.
The release function must only be used with high percussion pressure as a last resort to loosen jammed rods as it involves major stresses on the drilling equip-ment. Avoid using rotation together with the release function as the rod joints are tightened very tight!
Air blowing of drilled hole, option1. Stop the feed and rotation when finished drilling a hole.
2. Blow the hole clean for 5-10 seconds by moving the lever (Law) to is rearmost position.
3. Once air flushing is finished, move the rock drill back to its rear end position with control lever (Lf).
4. Position for the next hole and perform a new collaring.
Changing drill bit
Safety
Changing drill bit against rock face
N.B. Never start percussion with the drill bit free without any resistance.
WARNING Moving parts. Risk of personal injury, clothes can be
trapped. Switch off the rock drill rotation when
changing drill bits. Switch off hydraulic pumps if the
operator's panel is left unmanned.53
-
Operators instructions 9. Drilling1. Operate the feeder until the drill centre has good contact with the rock face.
2. Move the drill bit forward until it presses against the rock face and drill in about 5-10 cm.
3. Make sure the rotation lever (Lr) is in neutral.
4. Move the water flushing lever (Law) forward to cool the drill bit.
5. Start high pressure percussion and high feed force by moving the levers (Lh) and (Lf) to their foremost position for three to five seconds.
NoteIf an attempt to release the drill bit fails due to insufficient percussion pressure, use button (Blb) on the operator panel to attain high percussion pressure.
6. Return the rock drill to its rear position by pulling lever (Lf) towards the operator without rotation.
7. Unscrew the old drill bit by hand and replace with a new one.
Changing drill bit in bottom of hole
N.B. Never start percussion with the drill bit free without any resistance.
1. Cease drilling approx. 10 cm before the hole is fully drilled by moving the drilling levers to neutral position.
2. Make sure the rotation lever (Lr) is in neutral.
3. Move the water flushing lever (Law) forward to cool the drill bit.
4. Start high pressure percussion and high feed force by moving the levers (Lh) and (Lf) to their foremost position for three to five seconds.
NoteIf an attempt to release the drill bit fails due to insufficient percussion pressure, use button (Blb) on the operator panel to attain high percussion pressure.
5. Return the rock drill to its rear position by pulling lever (Lf) towards the operator without rotation.
6. Unscrew the old drill bit by hand and replace with a new one.54
-
Operators instructions9. DrillingCheck when drilling
Safety
Rock drill1. Make sure the rubber boot (A) is fitted on the rock drill adapter when carrying out
rising drilling.
Figure: Rubber boot
2. Always be observant for any water leaks from the rock drill.
3. See maintenance schedule, Rock drill.
System1. Make sure there are no fault indicator lamps on the electric cabinet. Attempt to
rectify any faults or call for service personnel.
2. Check the pressure gauges on the operator panel. If they suddenly show abnormal values, the drilling must be stopped immediately and the cause investigated.
3. Check the oil level in the hydraulic oil reservoir and top up as necessary. See maintenance instructions, Hydraulic systems: Changing oil.
4. Check the temperature of the hydraulic oil on the thermometer on the hydraulic oil tank. The temperature should be 30-60C during continuous drilling.
CAUTION Call for service personnel if a fault should
occur in the hydraulic, pneumatic or electrical systems while drilling is in progress.
Do not experiment with the systems. Simple faults can be made worse with risk
of personal injury.55
-
Operators instructions 9. Drilling5. Make sure there is oil in the lubricating oil tank and top up as necessary.
Figure: Lubricating oil tank
Hoses and couplings1. Make sure the percussion hoses to the rock drill do not vibrate abnormally. Vibrat-
ing hoses indicate malfunctioning accumulators on the rock drill. Stop drilling immediately and check or replace the accumulator. See maintenance instructions, Rock drill.
2. Ensure the hoses do not get trapped or jammed.
3. Make sure there are no leaks in hoses or couplings. Tighten or change leaking cou-plings and hoses.
SettingsFeed pressure
Setting feed pressureThe feed pressure must be adjusted to the drill bit diameter, bit type, percussion pres-sure, rock conditions, etc. It must be set so that the threaded joints of the drilling equipment do not come loose, causing abnormal wear or damage. Nor must the pres-sure be set too high, subjecting the drill rod to abnormal loads or increasing the risk of jamming.
When drilling in loose rock, it may be necessary to reduce the percussion pressure so that the feeder's maximum feed pressure is not exceeded.
NoteThe RPCF valve (V1a) must be disengaged while the feed pressure is adjusted. This is done by screwing the RPCF valve (V1a) clockwise as far as it will go.If the rig is equipped with a special reaming kit (option), there will be an RPCF valve for reaming (V1b). This must also be disengaged while the feed pressure is adjusted. (V1b) is to be disengaged in the same way as valve (V1a).
1250 0037 9056
-
Operators instructions9. DrillingFeed pressure for collaring1. The percussion lever (Lh) must be at the middle position (low percussion pres-
sure) and the feed lever (Lf) must be at its forward position.
2. Undo the lock nut used for valve (Vfl).
3. Adjust the feed pressure for collaring on the valve (Vfl) with an Allen key. The pressure should be 35 bar for the DCS12 drilling system and 40 bar for the DCS 14 and 18 drilling systems.
4. The pressure can be read on the feed pressure gauge (Gf).
5. Tighten the lock nut used for valve (Vfl).
Feed pressure for full drilling1. If the rig is equipped with a special reaming hole kit (option), make sure that lever
(Lrb) is at the small hole position.
2. Loosen the lock knob used for valve (Vfh).
3. Regulate the feed pressure for full drilling by means of the setting knob for pres-sure control valve (Vfh).
Turning the setting knob clockwise increases the feed pressure.
4. Read the pressure from pressure gauge (Gf).
5. Tighten the lock knob.
NoteIf the characteristic of the rock varies, the feed pressure for full drilling may need to be adjusted.
Feed pressure for full drilling of reaming holes, option1. Check that the percussion lever is in its forward position.
2. Check that lever (Lrb) is in the reaming hole position.
3. Remove the protective cap on pressure control valve (V6).57
-
Operators instructions 9. Drilling4. Adjust the feed pressure for reaming on the pressure control valve (V6) to 50-70 bar with an Allen key.
Figure: Detail of valve (V6)
Turning the adjusting screw clockwise increases the feed pressure.
5. The pressure can be read on the feed pressure gauge (Gf).
6. Refit the protective cap.
Feed pressure for telescopic feeder, option
IntroductionThe telescope feeder operates in two steps. Step 1 (lower cylinder) moves both beams from fully extended position to fully contracted position. Step 2 (upper cylinder) feeds the rock drill cradle forward on the upper beam.
Figure: Two-step operation of telescope feeder
The feed pressure during step 2 (upper cylinder) must be approx. 45 bar lower than the feed pressure during step 1 (lower cylinder). This lower pressure is regulated by pressure control valve (V8) and does not normally require adjustment.
1250 0062 38
V6
Lrb
1250 0072 8058
-
Operators instructions9. DrillingMax. feed pressure (upper and lower cylinder)The pressure must not be adjusted when drilling.
1. To prevent the limit switch from being activated, place a wooden block (10-20 cm thick) in the feeder in before the front drill-steel support.
2. Make sure all the control levers on the operator panel are in neutral.
3. Start the pump.
4. Run the rock drill towards the wooden block using lever (Lf).
5. Screw valve (Vfh) clockwise as far as it will go to disengage the valve.
6. Undo the lock nut for valve (Vfm).
Figure: Detail of valve (Vfm)
7. Adjust the setting screw to 140 bar. Read off the pressure on the pressure gauge (Gf).
8. Tighten the lock nut.
9. Reset valve (Vfh).
10. Run the rock drill back to its rear end position.
11. Turn off the pump.
12. Remove the wooden block.
Pressure difference between upper and lower cylinderThe feed pressure for the upper cylinder should normally be approx. 45 bar lower than the feed pressure for the lower cylinder. If the telescope feeder is not operating satisfactorily, it may be necessary to adjust the pressure difference. A suitable setting must be determined by trial and error in each individual case.
1. Connect a pressure gauge to pressure test outlet (G2).
2. Check that the drill levers are in neutral.
1250 0067 79
Vfm59
-
Operators instructions 9. Drilling3. Start the hydraulic pump.
4. Run the rock drill towards the wooden block using lever (Lf).
5. Adjust the pressure on valve (V8). Turning the valve knob clockwise will increase the pressure difference.
Figure: Detail of valve (V8) and (V17)
Feed pressure for collaring and full drillingThe feed pressure for collaring and full drilling is set in the same way as a standard feeder.
Feed pressure, reverse1. Connect a pressure gauge to pressure test outlet (G8).
2. Check that the drill levers are in neutral.
3. Start the hydraulic pump.
4. Activate reverse feed. Read the pressure on the pressure gauge when the rock drill cradle and upper feed beam are at their rear end positions. The pressure must be 120 bar.
V17
V8
1250
013
6 1260
-
Operators instructions9. Drilling5. Adjust the pressure as necessary on valve (V17). Turning the adjusting screw clockwise will increase the pressure.
Figure: Detail of valve (V8) and (V17)
Anti-jamming protection
DescriptionThere are two types of anti-jamming protection:
RPCF (feed control) Return movement of the feeder, usually simply called anti-jamming
The anti-jamming protection features are integrated and therefore interact. The fol-lowing is an example to show what happens when the protection is activated and what the result is.
If the drill bit tends to jam in the hole due to e.g. joints in the rock, the rotation pres-sure will start to increase and the feed pressure to drop successively to around 40 bar. If rotation pressure continues to rise, the feed will change direction and the rock drill will return. As the rotation pressure subsequently drops, the rock drill will change direction once more. If the drill bit still tends to jam, this procedure will continue until the bit has passed through the joint in the rock.
RPCF feed controlRPCF (Rotation Pressure Controlled Feed) is an anti-jamming device that is engaged in the following circumstances:
The drill bit tends to jam in the rock
Rotation pressure increases
Broken/worn drill bit
Low hydraulic oil temperature
V17
V812
50 0
136
1261
-
Operators instructions 9. DrillingWhen RPCF is activated, the feed pressure will gradually drop until it almost reaches zero.
Feed (rock drill) return movementWhen RPCF is activated and if the rotation pressure still rises then the second anti-jamming device will engage. This means that the feed will change direction and the rock drill will reverse. When the rotation pressure then decreases the rock drill changes direction again and moves forwards.
Setting the anti-jamming protection
General
When adjusting the anti-jamming protection, the following settings must be made in order:
Setting the feed return movement
Setting RPCF, small hole
Setting RPCF, reaming hole (if the optional reaming hole kit is installed)
When the RPCF is to be set, there are two ways to proceed:
Setting RPCF during drilling Setting RPCF in a workshop
Setting the feed return movementNoteThe hydraulic oil must be at normal operating temperature before setting.
Valve (Vaj) must be used to set the rotation pressure at which the rock drill is to change direction.
1. Check the rotation pressure during normal drilling. The rotation pressure can be read on pressure gauge (Gr).
2. Connect a pressure gauge to pressure test outlet (G3).
3. Undo the lock nut used for valve (Vaj).
4. Adjust the set screw to 30-40 bar above the normal rotation pressure. Read the pressure from a pressure gauge connected to pressure test outlet (G3).
If the valve is adjusted too low, the rock drill will change direction too early.
If the valve is adjusted too high, the rock drill will not change direction and the risk of jamming will increase.62
-
Operators instructions9. Drilling5. Tighten the lock nut.
6. Now set RPCF before making any further settings.
Setting RPCF during drillingNoteThe hydraulic oil must be at normal operating temperature before setting.
Normal rotation pressure settings for drilling are 35-50 bar for small holes and 40-50 bar for reaming holes. If the pressure rises above normal, there is risk that the drill steel will jam. The RPCF valve must therefore be activated if the normal rotation pressure rises by about 20 bar during drilling.
Valve (V1a) affects the rotation pressure at which the feed pressure will start to be reduced for a small hole drill bit.
Valve (V1b) affects the rotation pressure at which the feed pressure will start to be reduced for a reaming hole drill bit.
1. If the rig is equipped with a reaming kit (option), make sure that lever (Lrb) is in the correct position.
2. Find some homogeneous rock in the area being drilled.
3. Screw in the adjusting screw used for the RPCF valve all the way.
4. Collar the hole firmly and proceed to full drilling at a suitable feed pressure.
5. Read the rotation pressure on the pressure gauge (Gr).
6. Screw out the adjusting screw used for the RPCF valve until the feed pressure starts to drop.
7. Screw in the adjusting screw used for the RPCF valve about one turn.
One turn corresponds to about 20 bar of rotation pressure.
A 20 bar increase in the normal rotation pressure is needed during full drilling before the RPCF function will start to reduce the feed pressure.
8. Tighten the RPCF valve lock nut.63
-
Operators instructions 9. DrillingAfter drilling
Safety
Freeze prevention measuresThe water system must be drained in temperatures close to or below 0C, see opera-tor's instructions, Daily inspection.
WARNING Rock drills can start moving
unintentionally when the diesel engine is started.
May cause serious personal injury. Make sure that the feed levers for the rock
drill are in neutral position before the diesel engine is started and when drilling is finished.64
-
Operators instructions10. Extension drilling10. Extension drilling
Equipment for extension drilling
Figure: Feeder with opening drill-steel supportA Opening front drill-steel support, BSH 110B Splicing rod
Manual rod extension means that one or more drilling rods are manually joined using the opening front drill-steel support (BSH 110).
B
A
1250 0064 3765
-
Operators instructions 10. Extension drillingOperator panel
Figure: Operator panelLr Rotation leverLh Percussion leverLf Feed leverLds Lever to open/close front drill-steel support BSH 110Ltf Feed lever for threading and unthreading rodsLrn Single-rod/extension drilling selector lever
Lr Lh Lf
Lrn
Lds
Ltf
1250 0070 1466
-
Operators instructions10. Extension drillingOperating
Safety
Manual rod adding
Preparation1. Remove bolt in intermediate drill-steel support by:
WARNING Moving and rotating components inside
the working area of the booms. May cause serious personal injury. Make sure that no personnel remain
inside the working area of the booms before any work is started.
Always switch off the hydraulic pumps when manual work shall be carried out inside the working area of the booms.
Always switch off the hydraulic pumps if the operator's station is left unmanned.
WARNING Risk of falling drill rods. Risk that coupling equipment shall
continue to move. May cause serious personal injury. Make sure that the lever positions
correspond to the position of the equipment, when starting electrically and/or diesel driven hydraulic pumps.67
-
Operators instructions 10. Extension drillinga. Remove pin (6).
Figure: Intermediate drill-steel support
b. Remove bolt (5).
c. Place the bolt in holder (7).
2. Change the front drill-steel support bush to the correct dimension so that the join between two drill rods can pass without obstruction.
3. Select the extension drilling function with the drilling/joining lever to prevent automatic rock drill return.
Drilling and extension1. Drill in the first rod.
NoteOpen the drill-steel support with the lever for the hydraulic drill-steel support before the join between the drill rod and the shank adapter reaches the drill-steel support.
2. Hammer towards the bottom of the hole to separate the drill rod from the shank adapter.
3. Make sure the threaded joint is located in the drill-steel support.
4. Close the drill-steel support with the lever for the hydraulic drill-steel support.
5. Unscrew the shank adapter from the drill rod by activating reverse feed with the threading/extension drilling lever and right rotation with the rotation lever.
6. Reverse the rock drill with the feed lever so that there is room to screw on a new rod.
7. Turn off the hydraulic pumps.
8. Screw together the new drill rod by hand with the drill rod that was drilled into the rock.
5
6
71250 0061 5968
-
Operators instructions10. Extension drilling9. Start the hydraulic pumps and move the rock drill forwards with the feed lever so that the shank adapter comes as close as possible to the drill rod join.
10. Turn off the hydraulic pumps.
11. Screw together the drill rod by hand with the shank adapter.
12. Start the hydraulic pumps and tighten the joins by activating forward feed with the feed/extension drilling lever and left rotation with the rotation lever.
13. Open the drill-steel support with the hydraulic drill-steel support lever.
14. Start drilling.
15. Repeat steps 3 - 13 for each new drill rod to be added.
Removing drilling rods1. Make sure the drill-steel support is open.
2. Hammer towards the bottom of the hole to loosen the joins.
3. Make sure the front join on the last drill rod is located in the drill-steel support.
4. Close the drill-steel support with the lever for the hydraulic drill-steel support.
5. Unscrew one of the drill road joins completely by activating reverse feed with the feed/extension drilling lever and right rotation with the rotation lever.
6. Turn off the hydraulic pumps.
7. Unscrew the other end of the drill rod by hand.
8. Start the hydraulic pumps and move the rock drill to the drill-steel support.
9. Screw the shank adapter to the next drill rod by activating forward feed with the feed/extension drilling lever and left rotation with the rotation lever.
NoteDo not screw together too tightly so the join cannot be unscrewed. The last drill rod must be screwed tight however.
10. Open the drill-steel support with the hydraulic drill-steel support lever.
11. Repeat steps 3 - 10 with the remaining drill rods.69
-
Operators instructions 11. Directional control11. Directional control
FAMDirectional control FAM (Feed Angle Measurement) is available in two designs:
FAM I with angle indication FAM II with angle indication and hole depth measurement
Angle indication involves measurement and indication of the feeder's direction. The system calculates the deviation from the defined reference direction, which the feeder's direction should give with a full depth drilled hole. The deviation is pre-sented in cm.
For the system to present the correct values, the user must specify a reference direc-tion and a length for a full depth drilled hole (not drill steel length).
The system also shows instantaneously the attained hole depth when drilling, if equipped with hole depth measurement
Control panel
Figure: Control panel
Table: Buttons
Button DescriptionA-D Direct selection button. These buttons are only active
in certain menus and the function is then illustrated by a symbol on the left-hand edge of the menu.
A
B
C
ESC
D
1250
015
6 4070
-
Operators instructions11. Directional controlOperating
Start
Figure: Switch
Start the system by turning the switch to position 1.
Escape key (ESC). Goes back one step in the menu structure. Also has an undo function when entering numerical values. By pressing Escape instead of ENTER, you erase an input value.
Left arrow key. Moves the cursor to the left.
Up arrow key. Moves the cursor upwards. Also used to increase a numerical value.
Down arrow key. Moves the cursor downwards. Also used to decrease a value.
Right arrow key. Moves the cursor to the right.
ENTERUsed to confirm a selected option or a changed numerical value.This button is also used to activate the boxes in which a numerical value is changed.
Button Description
ESC
1250 0059 30
1250 0059 50
1250 0059 51
1250 0059 52
1250 0059 53
1250 0059 54
0 1
1250 0089 82
FAM/ARI71
-
Operators instructions 11. Directional controlMenus
Figure: Menu structure
Main menu
Figure: Main menu
The main menu is shown on the display screen once the system has started. From here, you can go directly to the working menu Drift drilling (1), the menu that is of the greatest use to operator.
The other menu system contains menus to make settings and for information that can be of use when fault finding. The menu system can be seen as a tree divided up into six branches.
1
22.1
5.1
2.2
5.2
3 3.13.2
4
5
61250 0068 22
1250 0061 97
1 2
3
4
5
672
-
Operators instructions11. Directional controlMenu tree, branch 1
Figure: Menu tree, branch 1
Branch 1 contains Working menu Drift drilling
Table: Menus branch 1
Menu tree, branch 2
Figure: Menu tree, branch 2
Branch 2 contains menus related to the boom sensor.
Menu Description1The working menu shows feed direction and the specified length for a full depth drilled hole. You can also specify a new reference direction here.If the system features hole depth measurement the hole depth reached is shown and you can also reset the hole depth once the hole has been completed.
11250 0080 52
250 cm
23 1250 0059 26
167 cm
2 4 6 8 10
2
2.1 2.21250 0076 9473
-
Operators instructions 11. Directional controlTable: Menus branch 2
Menu Description2Go to 2.1 to see the sensor angles or to 2.2 to calibrate (=0) the sensor.
2.1Sensor angles. Shows measured angles for the boom swing, feed swing and feed inclination. This information may be useful when fault finding in order to check whether the sensors work as intended. X6 - X12 are sensor connections on the resolver module.
2.2Menu for calibrating the sensors after replacing a sensor or resolver module. Password protected. See maintenance instructions, Directional control: Sensor calibration. X6 - X12 are sensor connections on the resolver module.
= 0
1250 0061 78
-11.2
-11.2
23.6
X6
X7
X12
1250 0059 16
-11.2
-11.2
23.6
X6
X7
X12
1250 0059 17
+1
-1
-123
xC=074
-
Operators instructions11. Directional controlMenu tree, branch 3
Figure: Menu tree, branch 3
Branch 3 contains the menus for drilling settings.
Table: Menus branch 3
Menu Description3Settings. Go to 3.1 for setting the length of a full depth drilled hole or 3.2 for calibrating a length sensor (only systems with hole depth measurement).
3.1Setting the length of a full depth drilled hole.
1250 0080 53
3
3.1 3.2
1250 0062 89
cm250
1250 0059 1875
-
Operators instructions 11. Directional controlMenu tree, branch 4
Figure: Menu tree, branch 4
Branch 4 contains a menu for setting display screen brightness.
Table: Menus branch 4
3.2 (only systems with hole depth measurement)Menu for calibration of the length sensor.
Menu Description4Menu for setting display screen brightness. Setting values 1 - 9. NOTE: Screen brightness will be changed after a slight delay.
Menu Description
1250 0062 90
=0
X10
xC
+10 4 cm
41250 0080 54
5
1250 0061 8376
-
Operators instructions11. Directional controlMenu tree, branch 5
Figure: Menu tree, branch 5
Branch 5 contains menus for fault finding/diagnostics
Table: Menus branch 5
Menu Description5Go to 5.1 to see the status of the display screen module or 5.2 to see the status of the sensor and resolver module.
5.1Menu showing display screen status: OK or NOT OK (crossed-out OK).
5
5.1 5.21250 0080 51
1250 0061 87
5.1
5.2
OK
1250 0061 8877
-
Operators instructions 11. Directional controlMenu tree, branch 6
Figure: Menu tree, branch 6
Branch 6 contains a menu to define the password.
Table: Menu branch 6
5.2Menu that shows the status of the connectors on the resolver module that are connected to a sensor. The status of the connectors can have two values OK or NOT OK (crossed out OK).X6, X7 and X12 are the sensor connections on the resolver module.
Menu Description6The menu to define the password when you wish to access the system's password protected menus.
Menu Description
OK
OKOK
OK X6
X7
X12
1250 0061 96
1250 0076 986
******
1250 0061 9078
-
Operators instructions11. Directional controlWorking menu
Figure: Working menu1 Zeroing hole depth measurement2 Reading of user defined reference direction3 Selection of reference direction4 Maximum hole depth5 Vertical deviation6 Feed direction7 Measured hole depth
The feed direction is shown graphically in the form of a target where the bull's-eye represents the starting point of the hole. The target shows where the hole finishes up in the bottom of the blast. If the feeder is directed according to the reference direc-tion, the hole will end up in the centre of the target. Otherwise, there will be a devia-tion that is indicated with a line (6).
According to the figure above, the hole will deviate about 7 cm both vertically and horizontally.
The angle display will always be based on drilling the maximum depth of hole, i.e. according to the value at (4). Maximum hole depth must therefore be set before angle display will work.
The type of reference direction must also be chosen (3). If the rig symbol is chosen, the system will use a predefined reference direction, i.e. the rig's longitudinal axis. If the tunnel symbol is chosen instead, an optional reference direction can be defined.
If the hole depth measurement option has been chosen, the measured hole depth will be displayed (7). This also means it is possible to zero hole depth measurement (1).
250 cm
72 1250 0155 68
167 cm
2 4 6 8 10
1
2
3
4 5
6
779
-
Operators instructions 11. Directional controlMaximum hole depth
Figure: Setting maximum hole depth
Change the value for the maximum hole depth as follows:
Display the menu for setting the maximum hole depth. Place the cursor on the box with the numeric value and press Enter. Use the right and left arrow keys to place the cursor over the digit (ones, tens or
hundreds) that is to be changed. Change the value with arrow up (increase value) or arrow down (decrease value). When the entire value (all three digits) is correct, press ENTER for the system to
save the new value.
Reference directionThere are two alternatives for reference direction, Rig and Tunnel .
Rig Rig means that the longitudinal axis of the rig will be used as reference direction.
cm250
1250 0059 1880
-
Operators instructions11. Directional controlFigure: Reference direction Rig
Select the Rig reference direction as follows:
Open the working menu on the display screen. Press button (C) to show the rig symbol.
Figure: Working menu
If the rig symbol is displayed in the working menu, then the Rig reference direction is selected. The system will then show the direction of the feeder in relation to the longitudinal direction of the rig.
This alternative can be used when it is possible to set up the rig in alignment with the drilling direction.
1250
015
5 65
2 4 6 8 10
250 cm
72
A
B
C
ESC
167 cm
1250
015
6 41
ESC81
-
Operators instructions 11. Directional controlTunnelThe Tunnel alternative requires a user-defined reference direction. This can be used when the rig cannot be set up straight.
Figure: Reference direction Tunnel
Proceed as follows:
Align the feeder in the required drilling direction. Open the working menu on the display screen.
Figure: Working menu
Press button (C) to display the tunnel symbol instead of the rig symbol. Press button (B) and the system will read the new reference direction, i.e. the
direction of the feeder. The line on the target will now disappear and be replaced by a dot in the centre of the target.
After reading the reference direction, it will apply to all the booms on the rig.
1250
015
5 66
2 4 6 8 10
250 cm
72
A
B
C
ESC
167 cm
1250
015
5 6982
-
Operators instructions11. Directional controlTo return to the Rig reference direction, press button (C).
Hole depthIf the system has hole depth measurement, the attained hole depth (7) will be dis-played in centimetres.
Figure: Working menu
The holed depth is zeroed for each new hole drilled using the button with the zero symbol (1).
Fault indicationThe system indicates a fault by:
display a warning on the display screen. The warning is shown when a fault arises in CAN communication.See maintenance instructions, Directional control: Fault finding.
250 cm
72 1250 0155 68
167 cm
2 4 6 8 10
1
2
3
4 5
6
783
-
Operators instructions 11. Directional controlFigure: Warning. Fault in CAN communication.
shows a warning triangle in the lower right-hand corner of the display screen (in the main menu or working menu).See maintenance instructions, Directional control: Fault finding.
Figure: Warning triangle
1250 0060 86
1250 0085 2484
-
Operators instructions12. Shift control, option12. Shift control, option
APC 50 (Automatic Powershift Control
Description of operationThe APC 50 shift control is used to prevent incorrect downshifting and changes in direction of travel that otherwise could damage the transmission.
Speed reduction must be done by releasing the accelerator and using the service brakes. Reducing speed by downshifting can damage the transmission and is there-fore prevented with APC 50.
The direction of travel, from forwards to reverse or from reverse to forwards, may only be changed while the rig is stationary. Changing the direction of travel while the rig is in motion can damage the transmission and is therefore prevented by APC 50.
Changes in the direction of travel and downshifting can be done at the following approximate speeds.
Table: Speed limits for downshifting and changing direction of travel
When attempting to downshift or change direction of travel at the wrong speed, the right-hand point of the display will flash to make the driver aware that this measure is not allowed and will therefore be prevented by APC 50.
Every attempt to make a forbidden gearchange is registered by APC 50 and is saved in its internal memory.
Shifting procedure Speed limit3rd gear - 2nd gear 9 km/h2nd gear - 1st gear 5 km/h1st gear - Neutral 3 km/hChanging direction of travel 0 km/h85
-
Operators instructions 12. Shift control, optionControl panel
Figure: Control panel1 DisplayM Button for selecting display modeT LED, has different functions for the different display modesF LED, indicates an internal fault in the control unit
The control panel display (1) can show the following information.
Gear and direction of travel RPM (turbine shaft speed) Tramming speed Input signals (for diagnostics) Output signals (for diagnostics) Fault codes
Output signals are not shown during normal operation. APC 50 must be restarted before output signals can be seen, see maintenance instruction Shift control.
Fault codes are shown automatically if a fault occurs in the APC 50 system. The LED (T) will flash when a fault code is displayed as well.
Display mode, i.e. the type of information to be displayed, can be selected with the (M) button. Pressing the button will change the display mode as shown in the follow-ing figure.
T F
M
1
1250 0068 0586
-
Operators instructions12. Shift control, optionFigure: Display mode for normal operationA Display mode for current gear and direction of travelB Display mode for turbine shaft speedC Display mode for tramming speedD Display mode for input signals
Display of current gear and direction of travelWhen display mode for current gear and direction of travel is selected, the left-hand side of the display will show the direction of travel and the right-hand side the gear that is engaged. The following figure illustrates an example of the display with the current gear and direction of travel shown.
A
B
C
D1250 0068 0687
-
Operators instructions 12. Shift control, optionFigure: Example of display showing gear and direction of travel1 Forward and 1st gear2 Reverse and 2nd gear3 Neutral and 3rd gear
Display of turbine shaft speedThe LED (T) will come on when the turbine shaft speed display mode is selected.
The following figure is an example of how the display shows the turbine speed (rpm). At speeds lower than 999 rpm, the right-hand side of the display shows the tens and the left-hand side the hundreds. At speeds higher than 999 rpm, the right-hand side of the display will show hundreds and t