Download - MERDİVEN MANUEL
-
8/8/2019 MERDVEN MANUEL
1/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 1 -
1. GENERAL
1.1 INSTALLATION PROCEDURE
TRUSS FIRST RUNNING
PIT & WELL INSTALLATION TEST & STEPWAY CHECK & LEVELING INSTALLATION
JOBSITE
ARRIVAL
TRUSS JOINT & (INTERMEDIATE SUPPORT
AXLE CHAIN SUPPORT BEAM EXTRUSION
JOINT INSTALLATION) INSTALLATION
OUTER DECK HANDRAIL FRAME HANDRAIL SKIRT PANEL
INSTALLATION INSTALLATION INSTALLATION INSTALLATION
GLASS GUIDE STRIP
INSTALLATION INSTALLATION
SWITCH ADJUSTMENT
& SECOND NEWEL SKIRT
RUNNING TEST INSTALLATION
TEST
RUNNING
INNER DECK
INSTALLATION
Figure 1.1 Escalator installation procedures
-
8/8/2019 MERDVEN MANUEL
2/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 2 -
1.2 ESCALATOR MAJOR COMPONENTS
Figure 1.2 Escalator major components
-
8/8/2019 MERDVEN MANUEL
3/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 3 -
Figure 1.3 Escalator section1.3 BALUSTRADE DIMENSION
Figure 1.4 Sample balustrade part dimension drawing
-
8/8/2019 MERDVEN MANUEL
4/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 4 -
For actual job site dimension, refer to the balustrade parts dimension drawing
which is contained in each escalator shipment package.
Figure 1.5 section dimension of escalator
-
8/8/2019 MERDVEN MANUEL
5/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 5 -
2. PIT & WELL WAY CHECK
Check the job site to install escalator by referring layout drawing and actual site
dimension such as rise, wellway length, pit depth, base plate size, etc.
Figure 2-1 Typical Truss and Wellway Layout
Figure 2-2 Typical Layout Check Check the Base Plate location and Welding condition.
Prearrange below with the General Contractor before starting installation ;
Temporary Power Supply.
Storage Area.
Access to the building for Truss & Overhead support for hoisting Truss assembly.
-
8/8/2019 MERDVEN MANUEL
6/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 6 -
3. TRUSS JOINING & HOISTING
3.1 TRUSS JOINING
Join truss by aligning and bolting "match holes" which is already drilled from our factory.
Make sure that shim plate shall not be slipped out while joining truss.
Figure 3-1 Truss joining3.2 AXLE CHAIN ASSEMBLY
Join the axle chain by joining lower part of chain first and then upper part of
chain by using chain block with some force.
NOTICE: Always use brand-new split pin. Never use even once used split pin.
Figure 3-2 Step chain jointing Figure 3-3 Truss moving
-
8/8/2019 MERDVEN MANUEL
7/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 7 -
3.3 TRUSS HOISTING & LEVELING
Hoist truss horizontally to prevent twist or damage of truss.
Adjust truss angle, floor finish line of building and floor plate with maintaining the
horizontal level at 4 (four) parts such as support angle, floor plate, W.P.(Working point)and
step by using truss-leveling bolt.
Insert shim between base plate and support angle, then weld base plate by using angle to
fix truss as shown on Figure 3-5.
NOTICE: Weld angle after installing Intermediate support beam, if Intermediatesupport beam is required.
Figure 3-4 Floor leveling Figure 3-5 Truss base plate work
NOTICE : Handrail will be worn out or slanted, if there are level differencebetween left and right hand side of Truss after truss installation.
4. INTERMEDIATE SUPPORT BEAM WORK
Install intermediate support beam to prevent from sagging of Truss, if intermediate
support beam is shown on layout drawing.
Weld and install support beam. (Figure 4-1)
-
8/8/2019 MERDVEN MANUEL
8/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 8 -
Figure 4-1 Intermediate support beam work
5. TRUSS WIRING, FIRST RUNNING TEST & STEP INSTALLATION
5.1 TRUSS WIRING
Connect the cables in the upper truss to the cables (or junction box) in the lower truss.
Test all the pre-installed safety switches and emergency stop switch.
5.2 FIRST RUNNING TEST
Do the first running test.
5.3 STEP INSTALLATION
NOTICE : Step installation or step removal can only be done at the inclinationpart of escalator.
Figure 5-1 Step Installation & removal
-
8/8/2019 MERDVEN MANUEL
9/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 9 -
6. PANEL SUPPORT EXTRUSION INSTALLATION
NOTICE: Adjust length [X] of mounting clamp assembly. (Figure 6-1) Install Panel Support Extrusion from the lower part.
Adjust length [A] of panel support extrusion by bolting. (Figure 6-2)
Check whether panel support extrusion is horizontal or not and then adjust it to be leveled
by using machinist level.
(UNIT: mm)
Figure 6-1 adjustment
Mark joint line of inner & outer deck and glass panel. (Figure 6-2)
Figure 6-2 Marking joint line of inner & outer deck and glass panel
NOTICE: If the level of mounting clamp is all different, glass lining-up work will not beeasy. Moreover, glass will be shaken and frictional resistance of inner surface of handrail will
be increased.
800TYPE1000
TYP
E
1200
TYPEFOR 588 STEPFOR 606
STEP
[X] 427.5 436.5 536 636
(UNIT: mm)
ESCALATOR
DEGREE[A] [B] [C]
30 477 220 903
-
8/8/2019 MERDVEN MANUEL
10/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 10 -
Figure 6-3 Panel support extrusion installation
-
8/8/2019 MERDVEN MANUEL
11/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 11 -
7. OUTER DECK INSTALLATION
Install a splice plate into the upper end of the lower curve deck. (Figure 7-2)
NOTICE: In case of parallel installation, the outer deck at the middle part shall beassembled first. Fasten bolts securely and finish all outer deck installation works
before taking next step.
NOTICE: Overall clearance between the tops and bottoms at the joint of two units ofescalators shall be same.
Figure 7-1 Outer deck installation
Figure 7-2 Outer deck splicing Figure 7-3 Mounting clamp
-
8/8/2019 MERDVEN MANUEL
12/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 12 -
8. GLASS PANEL INSTALLATION
573
1380
2121
11
22
22
2
2
23
233
3
909.
7
909.
7
Figure 8-1 Glass panel installation
2mm
2 GLASS
1 GLASS
PANEL SUPPORT
GLASS JOINT LINE
SHIM (3mm)
EXTRUSION JOINT
*REMOVE AFTER GLASS SETTING
Figure 8-2 3mm shims between glasses Figure 8-3 Glass panel section
NOTICE: Install a Glass vertically. Adjust high and low, left and right side width ofhandrail return guide.
Assemble a Glass accurately starting from bottom curve by setting the W.P. as standard.
Adjust 3mm gap for top and bottom part of joint of adjacent glasses by pre-assembling
variable glass.
Check whether Glass is being installed vertically or not by using machinist level.
Assemble top curve glass finally and then inspect vertical & horizontal level once more.
Readjust it by using mounting clamp, if required.
NOTICE: Two pieces of roughly 1/8" (3mm) thick padding will maintain space of panelsuntil all the glasses are installed and then shims will be removed. Leave 1/8"(3mm)
gap between each panels.
NOTICE: Maintain 3mm space between glasses. In case of 3mm gap is not maintainedthen handrail tension will be affected.
-
8/8/2019 MERDVEN MANUEL
13/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 13 -
9. HANDRAIL FRAME INSTALLATION
9.1 NEWEL HANDRAIL FRAME
Remove joint bars from the ends of the plastic handrail return guides and bolt them onto
the lower ends of the handrail newel guides.
Slip the lower newel guide onto the newel panel, and insert the joint block (with four holes)
to connect the newel with the panel support extrusion.
Drill holes into the newel to align with the holes in the joint block, and insert the
connecting bolts
Figure 9-1 Newel frame assembly
Figure 9-2 Newel frame fixed
-
8/8/2019 MERDVEN MANUEL
14/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 14 -
9.2 HANDRAIL FRAME
Inspect the gripper to make sure that it is fully seated on the panels.
Install lower curve handrail guide on the gripper.
Figure 9-3 Handrail frame assembly Install upper curve handrail guide on the gripper.
The holes for the splice block for the last piece must also be drilled. Carefully measure and
cut the last handrail guide piece to the required length.
Figure 9-4 Cut the variable Handrail frameNOTICE: Cut 30-40mm surplus part of variable handrail frame as shown on Figure 9-4while assembling variable handrail frame.
NOTICE: Readjust glass installation condition, if cutting part is out of the range of30 - 40mm.
-
8/8/2019 MERDVEN MANUEL
15/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 15 -
9.3 GUIDE STRIP INSTALLATION (ONLY FOR ALUMINIUM FRAME)
NOTICE: Do not splice Handrail Guide Strips.
Figure 9-5 Guide strip installation Figure 9-6 Trimming ends of guide strip
10. HANDRAIL & RETURN GUIDE INSTALLATION
10.1 PRELIMINARY SETUP
Figure 10-1 Return guide installation Figure 10-2 Do not handrail bent
Figure 10-3 Section of return guide
-
8/8/2019 MERDVEN MANUEL
16/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 16 -
NOTICE : Thoroughly clean debris, especially along the path of the handrail,inside of aluminum and plastic handrail guides.
NOTICE : Upper curve handrail return guide shall not be getting resistance.10.2 HANDRAIL INSTALLATION & ADJUSTMENT
1) Handrail guide system Confirm the return guide is located so there is enough clearance for the handrail under
the guide and between the guide and truss.
Install the newel return guide as following handrail adjusting guide. (Figure 10-4)
Line up disconnected part of return guide and adjusting guide. Mark and cut
adjusting guide 12mm below the point where guides over lap.
Install handrail on remaining adjusting guide.
Temporarily connect guides with Inner splice bar. Install outer splicing bar on return
guide, and tighten bolts. The outer splice bar on the adjusting guide is not installed until
step mentioned below, so that the inner splice bar is free to move while the
adjusting guide is adjusted.
700mm below splice, lift adjusting guide and handrail up toward top of balustrade. On
inner splice bar, mark end of adjusting guide. Release handrail and adjusting
guide. (Figure 10-4)
700mm below splice, push adjusting guide and handrail down away from balustrade.
On inner splice bar, mark end of adjusting guide. Release handrail and adjusting
guide. (Figure 10-4)
Find the midpoint of tension marks made by push adjusting guide up and down.
Adjust adjusting guide that the end of adjusting guide is located at midpoint of
tension marks. Attach outer splice bar on adjusting guide and tighten bolts.
Figure 10-4 Handrail tension adjustment
-
8/8/2019 MERDVEN MANUEL
17/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 17 -
2) Installation of handrail systemHandrail system is subassembly with circular moving handrail, which is supported for
holding by passenger. Because of limit of transportation, subassemblies of handrail system are
not convenience to install on the escalator (except special). Handrail system assembling is
divided to two times to finished. in the first time, debuggingchecking and remove to park are
finished in workshop, the second installation will be finished on building site, which is a
systemic engineering. See the appendix installation drawing.
Handrail system are composed of handrail driverguide panelhandrailhandrail entry
deviceskirt panelinner and outer deck and top and bottom turning parts.
The handrail in the handrail system is a motional parts for holding by passenger, which
speed should be accordance with speed of stepand should be ahead of step for 0-2.0%,
Which can be done by adjusting handrail drivers.
Handrail driving system is a subassembly to drive handrail to move circularly (Figure
10-5).
Figure 10-5 Handrail drive
1Tension screw 2Press tape 3Friction wheel 4Handrail
5Tension rod 6Screw 7Locknut 8Nut 9Press spring
Handrail are drove by friction wheel (3) with rubber tire, tension of handrail (4) may bedone by adjusting the nut 8 on the tension rod, and press handrail with press tape (4), tension
of press tape is adjusted with tension screw.
Tension force of handrail and press tape should be proper, and friction wheel will drive
handrail normally, at this time, it will take more strength to stop handrail. Tension of press tape
are kept continuously by spring (9), while operating tension rod (5), it must be done to removed
inner deck and skirt panel, and loose screw 6, release locknut (7), and adjust tension rod with
nut (8). While finished adjusting it must be remembered to tighten the locknut (7).
-
8/8/2019 MERDVEN MANUEL
18/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 18 -
11. SKIRT PANEL INSTALLATION
Install the lower curve skirt section onto the skirt support angle on the lower truss.
Check the skirt face is vertical to the steps. Both sides' gap between skirt panel and step
shall be within 4mm.
If the skirt is not vertical to the steps, loosen bolt with holding the skirt support angle.
Readjust it as required.
Figure 11-1 Skirt panel installation
1200TYPE:506.5
1000TYPE:405
800TYPE:304.5
SKIRTSUPPORTANGLE
SKIRTPLATETRUSS
CHORD
Figure 11-2 Skirt panel installation
-
8/8/2019 MERDVEN MANUEL
19/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 19 -
12. SECOND RUNNING TEST & SWITCH ADJUSTMENT
NOTICE : Remove dust on surface of track and dust in the machine room first and thendo second running test to prevent from breakage of step.
Adjust upper & lower skirt switch gap.
Check handrail running condition, skirt panel & step interference. Combplate & step guide roller adjustment
The teeth of the comb section "A"-"A" must mesh correctly with the cleats of the step
tread. If comb needs adjustment, see Figure 12-1.
The step guide rollers guide steps running smoothly without knocking. Adjust the rollers
or the skirt panels, if necessary.
There shall be clearance of 0.20.3mm between rollers and steps.
The top of the step guide rollers must be 5 2mm below from the top of the step tread.
Adjust rollers, if necessary.
Teeth of the combfinger shall be engaged with the grooves of the step tread byapproximately 6mm depth. Raise or lower the combplate, if necessary.
Figure 12-1 Combplate adjustment
Figure 12-2 Step guide roller adjustment
-
8/8/2019 MERDVEN MANUEL
20/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 20 -
13. INNER DECK INSTALLATION
Figure 13-1 Inner deck installation
Figure 13-2 Inner deck installation
-
8/8/2019 MERDVEN MANUEL
21/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 21 -
14. NEWEL SKIRT INSTALLATION
Figure 14-1 Top newel dimension
Figure 14-2 Bottom newel dimension
-
8/8/2019 MERDVEN MANUEL
22/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 22 -
1. Part Name
1) Skirt Panel
2) Inner Deck3) Outer Deck4) Handrail Frame5) Newel Skirt(Inner, Outer Side)6) Floor Plate7) M4 Screw (dish head)
2. Structure
-
8/8/2019 MERDVEN MANUEL
23/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 23 -
PartNo.
Part Name RemarkPartNo.
Part Name Remark
1 Direction Indicator Option 10 M5 Nut
2 Fixing Panel See Note 1 11 Newel Skirt(inner)
3 Acrylic Panel See Note 1 12 Sensor For Autostart Option
4 Newel Skirt(outer) 13 M5 Screw
5 Strip 14 Fixing Screw (ST2.9*9.5
6 Inlet Guard See Note 2 15 M5 Nut
7 Stud Bolt 16 Connect Panel
8 Spring 17 Fixing Screw (ST4.2*9.5
9 Plain Washer
Note1. Fixing panel ( 2 ) and Acrylic ( 3 ) are installed as part of direction indicator( 1 ).2.Use Inlet Guard ( 6 ) according to Handrail Frame ( Aluminum Alloy Type or Stainless
Steel Type ).
3. Installation and Adjustment* The Sequence of Installation
1) Check Parts before installation
Install the Inner Deck, Outer Deck, Skirt Paneland Handrail Frame.Note: Please refer to related dimensions inattached drawing when installing the parts aboveand adjust in time if the measured dimensions arenot matched.
-
8/8/2019 MERDVEN MANUEL
24/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 24 -
4) Install Screw (M5 and M4)M5 Screw (Pan Head) : Part No.7
M4 Screw (Dish Head) : Part No.13 in StructuredrawingNote: Do not fasten M4 Screw now, wait till thefinal installation and adjustment is over andfasten it at that time.
5) Install Handrail Inlet Guard (Part No. 6)(1) Split the top of the Inlet Guard by some
degrees (but not too much), put in theHandrail, then install the Inlet GuardAccording to the Arrow in the picture.(2) Stud Bolt, Spring and Plain Washer(Part No.7,8,9) are needed when installingthe Inlet Guard. Take care whether theseparts go loose when installing.
2) Install the Outer Newel SkirtPart No. 4 3) Install the Outer Deck ( Part No.11 )If the direction indicator is equipped, install itfirst and connect the related wiring, then installthe outer deck.Note: The arrow displayed in the DirectionIndicator panel indicates Escalator running
direction.
If the escalator is equipped with sensor forautostart, please install it first and connect relatedwiring before installing the Outer Deck.Note: Install the Inner Newel Skirt after fixingSpecial Nut on the skirt panel and fasten it
with Dish Head Nut(M4).
-
8/8/2019 MERDVEN MANUEL
25/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 25 -
6) Fasten the Handrail Guard andinstall the connecting parts (PartNo. 9,10,16)Install Sequence: Newel SkirtPlain WasherNutConnect Panel
(For Switch Operation)
Nut
Enlarged A
7 Install the Inner Deck(Part No.2)
First overlap the two decks byabout 15mm in the directionindicated by Arrow 1, then pushthe deck in the direction indicatedby Arrow 2 with considerableforce till the two decks are alignedto each other.
Note: Make sure the relatedwiring is connected before
installing. If possible, wiring in thispart should be connected in asocket way for the convenience ofinstallation and maintenance.
8) Ajustment and Test Run(1) Please refer to related dimensions ininstallation drawing and installation site. Adjust
the relative position of the parts and finally fastenall the Screws.(2) Start the escalator, check if Direction Indicator(Part No.1) and Sensor for Autostart (Part No.12)are normally working.(3) After installation, check if the Inlet Rubberinterferes with Handrail, if yes, adjust in time.
-
8/8/2019 MERDVEN MANUEL
26/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 26 -
5. Requirements of Packing, Transportation, and StorageTop, Bottom, Left and Right Newel Skirt should be packed in a carton after separately packedwith vinyl. The carton should be labeled a packing list, and stabilize the parts inside in case ofpossible damage during transportation.
Escalator Balustrade Installation DimensionsW-BT Model ( 30 and 35 degree)
SIZE
2 Flat Steps 3 Flat Steps
TOP BOTTOM TOP BOTTOM
30degree 35degree 30degree 35degree 30degree 35degree 30degree 35degree
a 804 1131 601 601
Dimensions [a, b, c, d, e ](of 2 Flat Steps) +
407
b 1195 1321.5 990.4 990.8
c 1219 1345.9 1015 1015
d 1413.6 1541.1 1209.5 1210.4
e 236.4 236.4 236.4 236.4
-
8/8/2019 MERDVEN MANUEL
27/27
W-BT ESCALATOR INSTALLATION GUIDE BOOK
HYUNDAI ELEVATOR CO., LTD. - 27 -
Brief Newel Assy Install Instruction
( )