Download - Mastur A
-
7/30/2019 Mastur A
1/14
< FACULTY >
SEPTEMBER 2012
OUMH2203
ENGLISH FOR WORKPLACE COMMUNICATION
MATRICULATION NO. :
IDENTITY CARD NO. :
TELEPHONE NO. :
E-MAIL :
LEARNING CENTRE :
-
7/30/2019 Mastur A
2/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
A REPORT REGARDING WITH THE IGNORANCE OF SAFETY REGULATIONS AT THE
MATERIAL AND HANDLING DEPARTMENT OF THE SHOE FACTORY AT PANTAI
MANIS PAPAR BRANCH
Prepared for:
The Managing Director,
Tingkat 2-4, Block B,
Wisma KOSAN Likas,
KM 7 Jalan Tuaran,
Locked Bag No. 89,
88992 Kota Kinabalu
Sabah.
By:
Mastura bte Abd Hamid,
The Occupational Health Manager,
KM 5, Jalan Pantai Manis,
Locked Bag No. 4,
89609 Papar,
Sabah.
-
7/30/2019 Mastur A
3/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
1. INTRODUCTION
Workplace health and safety can be a challenge, so awareness of occupational safety and health
is the most basic thing that each working person must possess. This awareness will indirectly
induce an employee to be more attentive and concerned about unsafe working such work
activity. The government outlines few key strategic thrusts through the 10 th Malaysian Plan
(2010) and one of them is creating conducive environment for unleashing economic growth
which will guarantee the safety of workers as well as boost their morale to give full commitment
to their employers and companies. This will then contribute to the reduction in accident rates in
the employment sector and increase the rate of national productivity and efficiency. With the
attainment of this end, Malaysia will be on the right track in achieving the status of a high
income country by 2020.
Work environment includes some factors, which either contributes positively or
negatively to achieving maximum employee productivity (Elywood, 1999). In order to fulfil the
nations dream come true, industrial manufactures are urged to ensure workplace environment to
be improved as it will enhance productivity. We cannot measure the effectiveness of a job design
without the knowledge of the working environment in which the design is place it is part of total
picture. The factors which either contributes positively or negatively to employee productivity
are temperature, humidity and air flow, noise, lighting, employee personal aspects, contaminants
and hazards in the working environment, types of sub environment. Therefore the employees
safety should be taken aware in line with the principle of the Occupational Safety and Health
Act, 1994 (2006).
In this report, it is hoped that the purpose will be given attention and understood as the
approval to this report will be a milestone to improve the present environment faced as well as
carry out the suggested actions in the proposal promptly in order to have a continuum production
without interrupting the previous plan and schedule. By doing so, the factorys environment will
be upgraded and the safeness to all workforces will be standardised in order to enhance
productivity and profitable income with demands from various sectors within the states.
1.1 PURPOSE OF REPORT
-
7/30/2019 Mastur A
4/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
The purpose of this report is to highlight the above matter to the Managing Director to foresee
the problems occurred at the Material and Handling department of the branch outlet and to
recommend the suggested possible measures that should be considered in order to improve the
safety standard of the workers and the workplace itself. Protection of workers safety and healthshould be of prime concern to employers as workers are at risk of exposing themselves to various
kind of hazard that exist because of the nature of work involved. As an Occupational Health
Manager, it is my responsibility to prepare the Occupational and Safety standards of the
company with prior knowledge to the Managing Director within this report.
For the Managing Directors information, I had been on a tour to the factory recently to
inspect the safeness of the environment at the Material and Handling department. After the
survey was done, I discovered that operators were blatantly ignoring the safety regulation, someof them have poor attitudes towards other fellow workmates and few regarded the regulations as
normal routine as if they were in no danger at all. Action should be promptly taken of before any
mishap would happen and put their lives in danger. Safety regulations in the workplace need to
be in place in order to assure workers that they are cared for. In this report, I would certainly
hope that my proposal would be to your fully attention and will be positively given the approval
with permission to implement them without delay to ensure that no incident would happen as
prevention is better than cure.
1.2 PROPOSAL
As mentioned above, I would like to propose a few changes to ensure that the department in the
shoe factory will be a more conducive workplace for the workers and the possible actions that
should be taken promptly are to set up an up-to-date safety regulations, standardise rules to be
followed, safety risk assessment schedule, discipline manners and proper protective equipment to
be worn during working hours as well as workshops and motivations to the workers. Should the
managing Director agrees with this proposal, I am sure the department at the shoe factory will be
a satisfactory outlet that will produce high quality and standard products before they are sent for
marketing. It is also my responsibility to make the workplace safe for the workers, so that
accident risks are prevented and to ensure they are at ease during working hours.
-
7/30/2019 Mastur A
5/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
2. THE FACTORY PRESENT SITUATION
KOSAN orKoperasi Serbaguna Sanya Berhad, is a multi-purpose co-operative society.
It has a branch outlet in Papar which is the sole manufacturer of shoes in Sabah. Its core business
is to produce white canvas shoes and now, it is in full production to cope with the demand from
local sectors as well as from neighbouring states. It is located at Jalan Pantai Manis, three and a
half miles from Papar town. It occupies a five acres site and it costs about five million to set up
the project. Being a member of the State Co-operative Coordinating Committee, Pantai Manis
KOSAN branch receives the assistance and guidance for their various multi-million projects. It
has also implemented countless projects introduced by the government over the years and this
has spawned job opportunities for the young generations in the district especially school leavers.
Since 1980, the performance of the workers was successful as hundreds of different kinds
of shoes have been anticipated to cater for the needs of the demanding sectors. Sabah Foundation
is one of the major clients for the need of supply of canvas shoes which are to be distributed
freely to all the local students in Sabah. KOSAN signed a 10-year contract with the government
in 2008 to supply these shoes to all primary students in the state. Besides that, there are also
some request and demands from neighbouring states like Brunei as well as West Malaysian, so it
is an advantage for the factory to supply shoes of high quality to the demanding states.
As mentioned above, the performance of the workers over the years made the districts
economic growth and proud besides being the sole local supplier of shoes in the state. The
factory produces up to 300,000 pairs of shoes on one shift operation per year. These shoes are
then packed and sent to the headquarters to be distributed according to the number of demands in
the marketplace. Formed under the Co-operative Act, this factory became the vehicle through
which youths who are members of SANYA (Sabah National Youth Association) could directly
participate in business opportunities provided by the government. The factory is constantly
upgrading the skills of its employees and investing in better technologies. Ironically, the factory
still needs improvement for better workplace and high attitude workforces which are problems
seen in some parts of the department and should be handled promptly. Anticipation of handling
these problems may make high quality production and increases profit when workers attitude
-
7/30/2019 Mastur A
6/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
turns positively during working hours. Nevertheless, these things would not happen if problems
are not handled.
3. THE PROBLEMS INVOLVED
Problems at the workplace are inevitable and understanding them is very important in order to
solve them. Sometimes, the problems are obvious, such as employees attitude or discipline
manners, employees safeness and ignorance of rules. Other times, the workplace itself harbours
the problem and we might not know the cause of it, thus creating a problem that needs solving.
They have to be dealt with tact and understanding. Therefore it is a need to identify the critical
ones, analyse and bring improvement on the performance. In other to make the workplace as adesired workplace for the workers, patience is a need and making a swift and effective actions
are better to stave off a major complicated situation. That is what needed to enhance the
production of the shoe factory at Pantai Manis branch outlet, so a survey was conducted at the
material and handling department. After the survey was conducted, I found out that the problems
encountered had caused a minor stress and unhappy air to the workers thus neglecting some
safety rules regulations. The problems encountered were:
i) Improper equipment
ii) Disorder arrangement and placement of materials
iii) Poor workers attitude
iv) Workplace environment
3.1 Improper Equipment
Workers use materials, chemicals, tools and machines to produce the different kinds of shoes.
Yet some of them are not properly equipped with things that they should have or do, like wearing
gloves, masks all the time and none of them wear earplugs. They do not have uniforms and no
-
7/30/2019 Mastur A
7/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
proper footwear. Working without proper equipment during operating the machines are
dangerous too as workers are exposed to dangers. They should wear safety equipment in order to
prevent any unexpected accidents prone happen especially at the finishing area. Chemicals from
leaks or spills may make workers attires get burn and so they scald. Malfunction of machineswhile sewing or miscalculation while cutting with sharp knives might occur at unexpected time.
If ever such situation happens, accident risks might happen, like getting scald, cut from sharp
tools or pricked from pointed needles, so wearing proper equipment can save workers from the
risks. Besides that, wearing masks can help workers from inhaling dust while packaging
materials and having wear earplugs will help them from noise pollution.
3.2 Disorder arrangement and placement of materials
The materials at the shoe factory are not stacked in proper places while the machines are not in
orderly arranged. The materials used are placed everywhere and are not arranged but disorderly
placed. Baskets are put here and there and the cut leathers are placed in a large open cabinet-like
which are exposed to flame. At the sewing area, there are workers personal things like
umbrellas and bags placed near the machines where they sit. At the assembling shoe area, the
materials are scattered on the table near the sewing machine and the ready-cut insole are placed
on shelves which can fall at any time during emergency. If the layouts of the area are properly
arranged, it would leads to a better condition and the workers would feel relieve. This is because
layout affects productivity and efficiency of material handling, time and throughput.
Arrangement of machines, materials and work areas could make process run smoothly,
eliminating all delays possible and provide efficient operations. In other words, arrangements
must be made to ensure safety and health in the use, handling or storage of products.
3.3 Poor workers attitude
Workers poor attitude is also one factor that contributes minor problem but can affects the
process of shoe manufacturing at the factory. Negative attitude of some workers made the others
felt unpleasant, thus bad feeling occurred and led to anger outburst among them. This was
-
7/30/2019 Mastur A
8/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
because few workers steal time off from working and let others finished the work. Conflict
occurred among them which resulted to the interruption of continuous process. Besides that,
there were also those who are in state of restlessness, despair and weariness. These changes of
negative attitude made them had bad feelings with others. Such situation made few responsibleworkers approached and asked for solution to problems faced and that made me had the tour to
the involved department. Factory workers should be able to work as a team and get along with
others and handling bad feelings among workers is one great task to be done. They should co-
operate among others to maintain positive attitude especially in packaging the finished product
before they are sent for marketing in order to achieve the factorys goal.
3.4 Workplace Environment
The workplace environment at the material and handling department looks less conducive. The
place needs reorganisation of arrangements and cleanliness. During the survey, I found out that
heaps of unwanted used materials are still kept at some corner, making the workplace looks in a
mess. There are no ventilation fans to let airflow and that made some workers look tired as there
is not much oxygen in the environment. The place is dusty too and there are cut threads and
materials on the floor as the workers are busy with their own activity at their own section. So
these matters expose the workers to harmful and unhealthy situation that might lead to some
healthy problems. Safety rules regulations should be attached in order for the workers to see
what they should do and dont. These safety regulations not only offer workers a safer
working environment, it saves time, work, business and money. If the workers follow the safety
rules, productivity may increases because workforce is more stable as the workers are focus with
their work.
4. CONCLUSIONS
The high quality production of the KOSAN shoe factory at Pantai Manis depends on the
workforces attitude and their safety as well as the workplaces environment. Safety rules
regulations, workshop and motivation are needed in order for the workers to stay alert and focus
-
7/30/2019 Mastur A
9/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
during the working shift hours especially handling or operating machines. Conducive
environment is a must to ensure the workers healthiness and easiness. In order to improve the
situation at the department involved and having thought of ways to handle problems
encountered, changes and recommendations are needed to upgrade the department, so that thefactorys goal will be successfully achieved.
4.1 THE NEED TO BE CHANGES AND RECOMMENDATIONS
At present, the workers at the KOSAN shoe factory branch outlet do not have uniforms. Only a
few of them wear gloves but none of them wear masks and earplugs. The department should
introduce a brand uniform for the workers to wear as image that shows to consumers the pride,responsibility and teamwork are happening at the factory. Wearing a uniform can also develop
standard identity as well as presentable appearance of the workers. Wearing gloves, masks,
earplugs and standardise footwear like sneakers or boots are safer for the workers too as wearing
them can make them easily move if there are emergencies happen. It is also easy for them to
move between corners where there are materials and machines arranged in order, for the use in
production of shoes demand.
As mentioned earlier, a healthy environment for a shoe factory will make workers feel at
ease as it looks neat and hygienic. Arranging materials in orderly will make the department site
look spacious. Moreover, arranging materials use to different segments will help the workers
easily look, take, use or keep them after use without difficulty. I think it is time for the factory to
have a change in the arrangement and storing materials and products before they are to be
commercial. It is also a need to maintain the cleanliness and conduciveness of the area before,
during and after working hours.
Workers attitude is also needed to change in order to achieve the factorys goal.
Workers attitude plays an important theme in performance that appraises focus. Respecting each
other is the most important factor to maintain quality of friendship that leads to achievement. For
this to happen, motivation is needed to refresh the workers mind and to regain self-
-
7/30/2019 Mastur A
10/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
consciousness and integrity. I need to improve the workers performance, so that their attitude
will also improve as well.
All in all, there is a need of changes to the workplace environment. The involved
department should be renovated into a more conducive situation. Dividing the department into
sections accordingly can make it looks spacious and easy for the workers to move around to their
own section respectively. In doing this initiative, I am sure the problems encountered will be
solved as well as upgrading the factory. Conducive environment is very important as it
influences the workers ability and mood effectively, so it needs to be supportive and
stimulating.
4.2 RECOMMENDATIONS
Accidents occur unannounced, so it is very important to be prepared for such mishaps and
workplace safety is an important aspect. The following recommendations should help improve
the condition occurred at the material and handling department in order to meet the needs of the
workers.
The workplace should be kept clean of any clutter. Appropriate places should be assigned
for storing or keeping materials used. Not only will this prevent unwanted accidents but it
will also increase the productivity of the workers.
The workers should be given clear instructions about their task. Ensure that the workers
have proper training to perform the task. Safety instructions should be included wherever
possible.
Regular maintenance program should be conducted once a week. Machinery that has
undergone wear and tear should be repaired or replaced immediately.
There should be exit drills or fire drills hold regularly. This is to ensure the workers are
well aware where safety equipment is stored or where to go when any danger situation
breaks out. Every worker should know where the fire extinguishers have been fixed and
know how to use them.
-
7/30/2019 Mastur A
11/14
-
7/30/2019 Mastur A
12/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
Laws of Malaysia AC 514: Occupational Safety & Health Act 1994. (2006). The Commissioner
of Law Revision Malaysia. Percetakan Nasional Malaysia Bhd.
Tenth Malaysian Plan 2011 2015. (2010). The Economic Planning Unit Prime Ministers
Department. Putrajaya.
Thesis:
Siti Farah Nadiah bte Taib. (2007). Design of an Improved Production Layout for a Shoe Making
Factory: A case study of a Company. University Teknologi Malaysia.
Journals:
Rajeshwar Bali. (1967). Workers Attitude to Work Volume 3. Pp 183 192. Shri Ram Centre.
Websites:
http://www.buzzle.com/articles/safety-regulations-in-the-workplace.html
http://www3.citadel.edu/hr/emp_relate/erprobinworkplace.htm
APPENDIX
http://www.buzzle.com/articles/safety-regulations-in-the-workplace.htmlhttp://www3.citadel.edu/hr/emp_relate/erprobinworkplace.htmhttp://www.buzzle.com/articles/safety-regulations-in-the-workplace.htmlhttp://www3.citadel.edu/hr/emp_relate/erprobinworkplace.htm -
7/30/2019 Mastur A
13/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
Picture 1: The Shoe Factory at Jalan Pantai Manis Papar
Picture 2: The Canvas shoes
-
7/30/2019 Mastur A
14/14
ENGLISH FOR WORKPLACE COMMUNICATION OUMH2203
Picture 3: A worker at the sewing section