INCHES/METRIC
MALLEABLE IRON THREADED FITTINGS
• 2 •
INDEX MALLEABLE IRON THREADED FITTINGS
PAGE
90˚ ELBOWSCLASS 150 M.I. ……………4CLASS 300 M.I. ……………12
90˚ REDUCING ELBOWSCLASS 150 M.I. ……………4
45˚ ELBOWSCLASS 150 M.I. ……………4CLASS 300 M.I. ……………12
CROSSESCLASS 150 M.I. ……………4CLASS 300 M.I. ……………12
TEESCLASS 150 M.I. ……………5CLASS 300 M.I. ……………12
REDUCING TEESCLASS 150 M.I. ……………6
COUPLINGSCLASS 150 M.I. ……………9CLASS 300 M.I. ……………12
REDUCING COUPLINGSCLASS 150 M.I. ……………9CLASS 300 M.I. ……………12
PAGE
90˚ STREET ELBOWSCLASS 150 M.I. ……………8
45˚ STREET ELBOWSCLASS 150 M.I. ……………8
CAPSCLASS 150 M.I. ……………10CLASS 300 M.I. ……………14
UNIONSCLASS 150 M.I. ……………10CLASS 300 M.I. ……………14
FLOOR FLANGESCLASS 150 M.I. ……………10
SQUARE HEAD PLUGS………………………………11
HEXAGON BUSHINGS. ………………………………11
• 3 •
STANDARDS
CCTF MALLEABLE IRON FITTINGS are designed to conform with the following industry standards:
MATERIAL: ASTM A 197 Cupola Malleable IronASTM A 153 Zinc Coatings
DIMENSIONS: ANSI/ASME B 16.3 Malleable Iron Threaded FittingsASME B 16.14 Ferrous Pipe Plugs, Bushings, etc.ASME B 16.39 Malleable Iron Threaded Pipe Unions
THREADS: ANSI/ASME B1.20.1 Pipe Threads. See data below. “Threading.”
IDENTIFICATION, MARKING
Class 300 Malleable Iron threaded fittings are marked with the numerals “300”, the letters “MI”, and the size.
Class 150 Malleable Iron threaded fittings have no pressure class markings.
THREADINGAll fittings shall be threaded with American National Standard Pipe Threads (ANSI/ASME B1.20.1) and shallhave taper threads, except wrought couplings and wrought caps in sizes 1/8, 1/4, 3/8 and 1/2, which may havestraight threads.
CONVERSION FACTORS
The International System (SI) metric equivalent of British units are shown throughout this catalogue.
NPS (Nominal Pipe Size) = DN* (Nominal Diameter)
Operating Pressure Class = PN* (Pressure Number)
1 inch = 25.4 millimetres
1 pound, weight = 0.4536 kilograms
1 pound, pressure = 0.06895 bars
*From the SI designations, Diamètre Nominal and Pression Nominale.
1 Permissible for service temperature up to 366˚F, reflecting the temperature ofsaturated steam at 150 psig.
2 14.5 psi = 1 bar = 100 kPa.
*All CCTF iron fittings are air pressure tested under water.
*PRESSURE-TEMPERATURE RATINGS
MALLEABLE IRON - ANSI B 16.3Temperature Class 300 psi2
Degrees C Degrees F
Class150psig
Sizes1/4 - 1
Sizes1/4 - 2
Sizes2 1/2 - 3
-29 to 66 -200 to 150 300 2000 1500 100093 200 265 1785 1350 910121 250 225 1575 1200 825149 300 185 1360 1050 735177 3661 1501 1150 900 650
204 400 935 750 560232 450 725 600 475260 500 510 450 385333 550 300 300 300
• 4 •
CLASS 150MALLEABLE IRONTHREADED FITTINGSASTM A197
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
90˚ ELBOWS 45˚ ELBOWS 90˚ REDUCING ELBOWS 90˚ REDUCING ELBOWS
Size
NPS
DN
Dimension
Approx.WeightA
Size
NPS
DN
Dimension
Approx.WeightC
Size
NPS
DN
Dimensions
Approx.WeightX Z
Size
NPS
DN
Dimensions
Approx.WeightX Z
1/8 .69 .07 *1/8 .69 .07 1/4x1/8 .74 .76 .08 1 1/2x1 1/4 1.82 1.88 .95
3 17.5 .03 *3 17.5 .03 6x3 18.8 19.3 .04 40x32 46.2 47.8 .43
1/4 .81 .11 1/4 .73 .11 3/8x1/4 .88 .90 .11 1 1/2x1 1.65 1.80 .86
6 20.6 .05 6 18.5 .05 10x6 22.4 22.9 .05 40x25 41.9 45.7 .39
3/8 .95 .15 3/8 .80 .15 3/8x1/8 .81 .85 .12 1 1/2x3/4 1.52 1.75 .66
10 24.1 .07 10 20.3 .07 10x3 20.5 21.6 .06 40x20 38.6 44.5 .30
1/2 1.12 .22 1.2 .88 .22 1/2x3/8 1.04 1.03 .19 2x1 1/2 2.02 2.16 1.4
15 28.5 .10 15 22.4 .09 15x10 26.4 26.2 .09 50x40 51.3 54.9 .63
3/4 1.31 .35 3/4 .98 .31 1/2x1/4 .97 .98 .18 2x1 1/4 1.90 2.10 1.3
20 33.3 .16 20 24.9 .14 15x6 24.6 24.9 .08 50x32 48.3 53.3 .60
1 1.50 .55 1 1.12 .51 3/4x1/2 1.20 1.22 .29 2x1 1.73 2.02 1.1
25 38.1 .25 25 28.5 .23 20x15 30.5 31.0 .13 50x25 43.9 51.3 .51
1 1/4 1.75 .93 1 1/4 1.29 .75 3/4x3/8 1.12 1.13 .24 2x3/4 1.60 1.97 .90
32 44.5 .42 32 32.8 .34 20x10 28.5 28.7 .11 50x20 40.6 50.0 .41
1 1/2 1.94 1.1 1 1/2 1.43 .97 3/4x1/2 1.05 1.08 .22 2 1/2x2 2.39 2.60 2.3
40 49.3 .49 40 36.3 .44 20x6 26.7 27.4 .10 65x50 60.7 66.0 1.04
2 2.25 1.8 2 1.68 1.6 *3/4x1/8 1.13 1.13 .31 2 1/2x1 1/2 2.16 2.51 2.2
50 57.2 .80 50 42.7 .71 *20x3 28.7 28.7 .14 65x40 54.9 63.8 1.01
2 1/2 2.70 2.9 2 1/2 1.95 2.4 1 x 3/4 1.37 1.45 .46 3x2 1/2 2.83 2.99 3.6
65 68.6 1.3 65 49.5 1.1 25x20 34.8 36.8 .21 80x65 71.9 75.9 1.62
3 3.08 3.9 3 2.17 3.3 1x1/2 1.26 1.36 .44 3x2 2.52 2.89 2.7
80 78.2 1.8 80 55.1 1.5 25x15 32.0 35.5 .20 80x50 64.0 73.4 1.21
3 1/2 3.42 6.2 3 1/2 2.39 5.8 1x3/8 1.18 1.27 .41 4x3 3.30 3.60 7.7
90 86.9 2.8 90 60.7 2.6 25x10 30.0 32.3 .19 100x80 83.8 91.4 .35
4 3.79 8.2 4 2.61 6.2 1 1/4x1 1.58 1.67 .75
100 96.3 3.7 100 66.3 2.8 32x25 40.1 42.4 .34
5 4.50 12.6 5 3.05 11.5 1 1/4x3/4 1.45 1.62 .57
125 114.3 5.7 125 77.5 5.2 32x20 36.8 41.2 .26
6 5.13 19.6 6 3.46 13.9 1 1/4x1/2 1.34 1.53 .51
150 130.3 8.9 150 87.9 6.3 32x15 34.0 38.9 .23
*These sizes not specified in ASME/ANSI B16.3
• 5 •
CLASS 150MALLEABLE IRON
THREADEDFITTINGS
ASTM A197
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CROSSES TEES
Size
NPS
DN A
Dimension
Approx.Weight
Size
NPS
DN A
Dimension
Approx.Weight
1/8 .69 .15 1/8 .69 .09
3 17.5 .07 3 17.5 .04
1/4 .81 .17 1/4 .81 .11
6 20.6 .08 6 20.6 .05
3/8 .95 .31 3/8 .95 .20
10 24.1 .14 10 24.1 .09
1/2 1.12 .30 1/2 1.12 .24
15 28.5 .14 15 28.5 .11
3/4 1.31 .49 3/4 1.31 .42
20 33.3 .22 20 33.3 .19
1 1.50 .79 1 1.50 .66
25 38.1 .36 25 38.1 .30
1 1/4 1.75 1.3 1 1/4 1.75 1.1
32 44.5 .57 32 44.5 .49
1 1/2 1.94 1.5 1 1/2 1.94 1.3
40 49.3 .66 40 49.3 .59
2 2.25 2.4 2 2.25 2.0
50 57.2 1.1 50 57.2 .91
2 1/2 2.70 4.6 2 1/2 2.70 3.6
65 68.6 2.09 65 68.6 1.61
3 3.08 6.1 3 3.08 5.0
80 78.2 2.76 80 78.2 2.28
3 1/2 3.42 8.6 3 1/2 3.42 7.2
90 86.9 3.89 90 86.9 3.28
4 3.79 11.9 4 3.79 9.3
100 96.3 5.38 100 96.3 4.23
5 4.50 22.0 5 4.50 17.2
125 114.3 10.0 125 114.3 7.82
6 5.13 23.9 6 5.13 22.9
150 130.3 10.84 150 130.3 10.40
• 6 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
Continued on page 7
CLASS 150Malleable Iron ThreadedREDUCING TEESASTM A197
Size Dimensions
NPS
DN X Y ZApprox.Weight
Size Dimensions
NPS
DN X Y ZApprox.Weight
1/4 x 1/4 x 1/8 .74 .74 .76 .12 1 x 3/4 x 1 1.50 1.45 1.50 .74
6 x 6 x 3 18.8 18.8 19.3 .05 25 x 20 x 25 38.1 36.8 38.1 .33
3/8 x 3/8 x 1/4 .88 .88 .90 .20 1 x 3/4 x 3/4 1.37 1.31 1.45 .62
10 x 10 x 6 22.4 22.4 22.9 .09 25 x 20 x 20 34.8 33.3 36.8 .28
3/8 x 1/4 x 3/8 .95 .90 .95 .19 1 x 3/4 x 1/2 1.26 1.20 1.36 .56
10 x 6 x 10 24.1 22.9 24.1 .09 25 x 20 x 15 32.0 30.5 35.5 .25
3/8 x 1/4 x 1/4 .88 .81 .90 .20 1 x 1/2 x 1 1.50 1.36 1.50 .68
10 x 6 x 6 22.4 20.6 22.9 .09 25 x 15 x 25 38.1 35.5 38.1 .31
1/2 x 1/2 x 3/8 1.04 1.05 1.03 .28 1 x 1/2 x 3/4 1.37 1.22 1.45 .59
15 x 15 x 10 26.4 26.4 26.2 .13 25 x 15 x 20 34.8 31.0 36.8 .27
1/2 x 1/2 x 1/4 .97 .97 .98 .26 1 x 1/2 x 1/2 1.26 1.12 1.36 .59
15 x 15 x 6 24.6 24.6 24.9 .12 25 x 15 x 15 32.0 28.5 35.5 .27
1/2 x 3/8 x 1/2 1.12 1.03 1.12 .30 1 1/4 x 1 1/4 x 1 1.58 1.58 1.67 1.11
15 x 10 x 15 28.5 26.2 28.5 .14 32 x 32 x 25 40.1 40.1 42.4 .52
1/2 x 3/8 x 3/8 1.04 .95 1.03 .27 1 1/4 x 1 1/4 x 3/4 1.45 1.45 1.62 .90
15 x 10 x 10 26.4 24.1 26.2 .12 32 x 32 x 20 36.8 36.8 41.2 .41
1/2 x 1/4 x 1/2 1.12 .98 1.12 .28 1 1/4 x 1 1/4 x 1/2 1.34 1.34 1.53 .86
15 x 6 x 15 28.5 24.9 28.5 .13 32 x 32 x 15 34.0 34.0 38.9 .39
3/4 x 3/4 x 1/2 1.20 1.20 1.22 .42 1 1/4 x 1 1/4 x 3/8 1.26 1.26 1.44 .75
20 x 20 x 15 30.5 30.5 31.0 .19 32 x 32 x 10 32.0 32.0 36.6 .34
3/4 x 3/4 x 3/8 1.12 1.12 1.13 .39 1 1/4 x 1 x 1 1/4 1.75 1.67 1.75 1.1
20 x 20 x 10 28.5 28.5 28.7 .18 32 x 25 x 32 44.5 42.4 44.5 .52
3/4 x 3/4 x 1/4 1.05 1.05 1.08 .35 1 1/4 x 1 x 1 1.58 1.50 1.67 1.1
20 x 20 x 6 26.7 26.7 27.4 .16 32 x 25 x 25 40.1 38.1 42.4 .52
3/4 x 1/2 x 3/4 1.31 1.22 1.31 .47 1 1/4 x 1 x 3/4 1.45 1.37 1.62 .83
20 x 15 x 20 33.3 31.0 33.3 .21 32 x 25 x 20 36.8 34.8 41.2 .38
3/4 x 1/2 x 1/2 1.20 1.12 1.22 .42 1 1/4 x 1 x 1/2 1.34 1.26 1.53 .78
20 x 15 x 15 30.5 28.5 31.0 .19 32 x 25 x 15 34.0 32.0 38.9 .35
3/4 x 3/8 x 3/4 1.31 1.13 1.31 .44 1 1/4 x 3/4 x 1 1/4 1.75 1.62 1.75 1.1
20 x 10 x 20 33.3 28.7 33.3 .20 32 x 20 x 32 44.5 41.2 44.5 .50
3/4 x 3/8 x 3/8 1.12 .95 1.13 .33 1/4 x 3/4 x 1 1.58 1.45 1.67 .92
20 x 10 x 10 28.5 24.1 28.7 .15 32 x 20 x 25 40.1 36.8 42.4 .42
3/4 x 1/4 x 3/4 1.31 1.08 1.31 .42 1 1/4 x 3/4 x 3/4 1.45 1.31 1.62 .90
20 x 6 x 20 33.3 27.4 33.3 .19 32 x 20 x 20 36.8 33.3 41.2 .41
1 x 1 x 3/4 1.37 1.37 1.45 .62 1 1/2 x 1 1/2 x 1 1/4 1.82 1.82 1.88 1.3
25 x 25 x 20 34.8 34.8 36.8 .28 40 x 40 x 32 46.2 46.2 47.8 .61
1 x 1 x 1/2 1.26 1.26 1.36 .59 1 1/2 x 1 1/2 x 1 1.65 1.65 1.80 1.2
25 x 25 x 15 32.0 32.0 35.5 .27 40 x 40 x 25 41.9 41.9 45.7 .56
1 x 1 x 3/8 1.18 1.18 1.27 .53 1 1/2 x 1 1/2 x 3/4 1.52 1.52 1.75 1.1
25 x 25 x 10 30.0 30.0 32.3 .24 40 x 40 x 20 38.6 38.6 44.5 .52
1 x 1 x 1/4 1.11 1.11 1.22 .55 1 1/2 x 1 1/2 x 1/2 1.41 1.41 1.66 .86
25 x 25 x 6 28.2 28.2 31.0 .25 40 x 40 x 15 35.8 35.8 42.2 .39
REDUCED ON RUNAND OUTLET
REDUCED RUN;OTHER END ANDOUTLET EQUAL
STRAIGHT RUN,REDUCING OUTLET
• 7 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 150Malleable Iron Threaded
REDUCING TEES continued
ASTM A197
Size Dimensions
NPS
DN X Y ZApprox.Weight
Size Dimensions
NPS
DN X Y ZApprox.Weight
1 1/2 x 1 1/4 x 1 1/2 1.94 1.88 1.94 1.6 2 1/2 x 2 1/2 x 1 1/2 2.16 2.16 2.51 2.9
40 x 32 x 40 49.3 47.8 49.3 .73 65 x 65 x 40 54.9 54.9 63.8 1.3
1 1/2 x 1 1/4 x 1 1/4 1.82 1.75 1.88 1.3 2 1/2 x 2 1/2 x 1 1/4 2.04 2.04 2.45 2.9
40 x 32 x 32 46.2 44.5 47.8 .61 65 x 65 x 32 51.8 51.8 62.2 1.3
1 1/2 x 1 1/4 x 1 1.65 1.58 1.80 1.2 2 1/2 x 2 1/2 x 1 1.87 1.87 2.37 2.6
40 x 32 x 25 41.9 40.1 45.7 .54 65 x 65 x 25 47.5 47.5 60.2 1.2
1 1/2 x 1 1/4 x 3/4 1.52 1.45 1.75 1.1 2 1/2 x 2 1/2 x 3/4 1.74 1.74 2.32 2.2
40 x 32 x 20 38.6 36.3 44.5 .50 65 x 65 x 20 44.2 44.2 58.9 1.0
2 x 2 x 1 1/2 2.02 2.02 2.16 2.1 2 1/2 x 2 x 2 1/2 2.70 2.60 2.70 4.1
50 x 50 x 40 51.3 51.3 54.9 .96 65 x 50 x 65 68.6 66.0 68.6 1.9
2 x 2 x 1 1/4 1.90 1.90 2.10 1.9 2 1/2 x 2 x 2 2.39 2.25 2.60 3.3
50 x 50 x 32 48.3 48.3 53.3 .89 65 x 50 x 50 60.7 57.2 66.0 1.5
2 x 2 x 1 1.73 1.73 2.02 1.6 *2 1/2 x 2 x 1 1/2 2.81 2.81 2.50 4.0
50 x 50 x 25 43.9 43.9 51.3 .73 *65 x 50 x 40 71.4 71.4 63.5 1.8
2 x 2 x 3/4 1.60 1.60 1.97 1.6 3 x 3 x 2 1/2 2.83 2.83 2.99 4.9
50 x 50 x 20 40.6 40.6 50.0 .72 80 x 80 x 65 71.9 71.9 76.0 2.2
2 x 2 x 1/2 1.49 1.49 1.88 1.3 3 x 3 x 2 2.52 2.52 2.89 3.9
50 x 50 x 15 37.9 37.9 47.8 .61 80 x 80 x 50 64.0 64.0 73.4 1.8
*2 x 2 x 3/8 1.49 1.49 1.88 1.6 3 x 3 x 1 1/2 2.29 2.29 2.80 3.7
*50 x 50 x 10 37.9 37.9 47.8 .73 80 x 80 x 40 58.2 58.2 71.1 1.7
2 x 1 1/2 x 2 2.25 2.16 2.25 2.3 3 x 3 x 1 1/4 2.17 2.17 2.74 3.7
50 x 40 x 50 57.2 54.8 57.2 1.0 80 x 80 x 32 55.1 55.1 69.6 1.7
2 x 1 1/2 x 1 1/2 2.02 1.94 2.16 2.1 4 x 4 x 3 3.30 3.30 3.60 8.1
50 x 40 x 40 51.3 49.3 54.9 .96 100 x 100 x 80 83.8 83.8 91.4 3.7
2 x 1 1/2 x 1 1/4 1.90 1.82 2.10 1.8 4 x 4 x 2 1/2 3.05 3.05 3.51 8.1
50 x 40 x 32 48.3 46.2 53.3 .82 100 x 100 x 65 77.5 77.5 89.2 3.7
2 x 1 1/2 x 1 1.73 1.65 2.02 1.6 4 x 4 x 2 2.74 2.74 3.41 6.8
50 x 40 x 25 43.9 41.9 51.3 .73 100 x 100 x 50 69.6 69.6 86.6 3.1
2 x 1 1/4 x 2 2.25 2.10 2.25 2.3 4 x 4 x 1 1/2 2.51 2.51 3.32 6.3
50 x 32 x 50 57.2 53.3 57.2 1.0 100 x 100 x 40 63.8 63.8 84.3 2.9
2 x 1/4 x 1 1/2 2.02 1.88 2.16 1.9 *4 x 4 x 1 1/4 2.75 2.75 3.44 6.1
50 x 32 x 40 51.3 47.8 54.9 .86 *100 x 100 x 32 69.9 69.9 87.4 2.8
2 x 1 1/4 x 1 1/4 1.90 1.75 2.10 1.9 *4 x 4 x 1 2.75 2.75 3.44 5.8
50 x 32 x 32 48.3 44.5 53.3 .89 *100 x 100 x 25 69.9 69.9 87.4 2.6
2 x 1 x 2 2.25 2.02 2.25 2.1 6 x 6 x 4 4.13 4.13 4.94 17.9
50 x 25 x 50 57.2 51.3 57.2 .95 150 x 150 x 100 104.9 104.9 125.5 8.1
2 x 3/4 x 2 2.25 1.97 2.25 2.1 6 x 6 x 3 3.64 3.64 4.75 16.1
50 x 20 x 50 57.2 50.0 57.2 .95 150 x 150 x 80 92.5 92.5 120.7 7.3
2 x 1/2 x 2 2.25 1.88 2.25 2.1 6 x 6 x 2 3.08 3.08 4.56 13.9
50 x 15 x 50 57.2 47.8 57.2 .95 150 x 150 x 50 78.2 78.2 115.8 16.3
2 1/2 x 2 1/2 x 2 2.39 2.39 2.60 3.3
65 x 65 x 50 60.7 60.7 66.0 1.5
*These sizes not specified by ASME/ANSI B16.3
• 8 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 150Malleable Iron Threaded
STREET ELBOWSASTM A197
45˚ STREET ELBOWS 90˚ STREET ELBOWS
Size
NPS
DN C K
Dimensions
Approx.Weight
Size
NPS
DN A J
Dimensions
Approx.Weight
*1/8 .69 .88 .06 1/8 .69 1.00 .07
*3 17.5 22.4 .03 3 17.5 25.4 .03
1/4 .73 .94 .09 1/4 .81 1.19 .09
6 18.5 23.9 .04 6 20.6 30.2 .04
3/8 .80 1.03 .13 3/8 .95 1.44 .13
10 20.3 26.2 .06 10 24.1 36.6 .06
1/2 88 1.15 .17 1/2 1.12 1.63 .22
15 22.4 29.2 .08 15 28.5 41.2 .10
3/4 .98 1.29 .29 3/4 1.31 1.89 .33
20 24.9 32.8 .13 20 33.3 48.0 .15
1 1.12 1.47 .46 1 1.50 2.14 .55
25 28.5 37.3 .21 25 38.1 54.4 .25
1 1/4 1.29 1.71 .79 1 1/4 1.75 2.45 .88
32 32.8 43.4 .36 32 44.5 62.2 .40
1 1/2 1.43 1.88 .93 1 1/2 1.94 2.69 1.1
40 36.3 47.8 .42 40 49.3 68.3 .52
2 1.68 2.22 1.5 2 2.25 3.26 1.8
50 42.7 56.4 .66 50 57.2 82.8 .81
2 1/2 2.70 3.86 2.9
65 68.6 98.0 1.3
3 3.08 4.51 3.9
80 78.2 114.6 1.8
4 3.79 5.69 8.4
100 96.3 144.5 3.8
*This size not specified in ASME/ANSI B16.3
• 9 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 150Malleable Iron Threaded
COUPLINGSASTM A197
COUPLINGS REDUCED COUPLINGS REDUCING COUPLINGS
Size
NPS
DN WApprox.Weight
Size
NPS
DN MApprox.Weight
Size
NPS
DN MApprox.Weight
*These sizes not specified in ASME/ANSI B16.3
*These sizes not specified in ASME/ANSI B16.3
1/8 .96 .07 1/4 x 1/8 1.00 .08 2 x 1 2.81 .93
3 24.4 .03 6 x 3 25.4 .04 50 x 25 71.4 .42
1/4 1.06 .07 3/8 x 1/4 1.13 .11 2 x 3/4 2.81 .81
6 26.9 .03 10 x 6 28.7 .05 50 x 20 71.4 .37
3/8 1.16 .11 3/8 x 1/8 1.13 .11 2 x 1/2 2.81 .90
10 29.5 .05 10 x 3 28.7 .05 50 x 15 71.4 .41
1/2 1.34 .18 1/2 x 3/8 1.25 .18 2 1/2 x 2 3.25 1.6
15 34.0 .08 15 x 10 31.8 .08 65 x 50 82.6 .72
3/4 1.52 .26 1/2 x 1/4 1.25 .13 2 1/2 x 1 1/2 3.25 1.4
20 38.6 .12 15 x 6 31.8 .06 65 x 40 82.6 .62
1 1.67 .44 1/2 x 1/8 1.25 .13 2 1/2 x 1 1/4 3.25 1.5
25 42.4 .20 15 x 3 31.8 .06 65 x 32 82.6 .67
1 1/4 1.93 .62 3/4 x 1/2 1.44 .22 2 1/2 x 1 3.25 1.0
32 49.0 .28 20 x 15 36.6 .10 65 x 25 82.6 .46
1 1/2 2.15 .90 3/4 x 3/8 1.44 .22 3 x 2 1/2 3.69 2.4
40 54.6 .41 20 x 10 36.6 .10 80 x 65 93.7 1.07
2 2.53 1.2 3/4 x 1/4 1.44 .20 3 x 2 3.69 2.1
50 64.3 .56 20 x 6 36.6 .09 80 x 50 93.7 .94
2 1/2 2.88 1.9 1 x 3/4 1.69 .35 3 x 1 1/2 3.69 1.9
65 73.2 .88 25 x 20 42.9 .16 80 x 40 93.7 .89
3 3.18 2.6 1 x 1/2 1.69 .31 3 x 1 1/4 3.69 2.0
80 80.8 1.2 25 x 15 42.9 .14 80 x 32 93.7 .92
*3 1/2 3.74 4.5 1 x 3/8 1.69 .31 3 x 1 3.69 2.0
*90 95.0 2.0 25 x 10 42.9 .14 80 x 25 93.7 .93
4 3.69 4.6 1 x 1/4 1.69 .30 *3 1/2 x 3 4.0 4.9
100 93.7 2.1 25 x 6 42.9 .13 *90 x 80 101.6 .22
*5 4.25 6.6 1 1/4 x 1 2.06 .55 *3 1/2 x 2 1/2 4.0 .44
*125 108.0 3.0 32 x 25 52.3 .25 *90 x 65 101.6 2.0
*6 4.75 9.9 1 1/4 x 3/4 2.06 .49 *3 1/2 x 2 4.0 4.2
*150 120.7 4.5 32 x 20 52.3 .22 *90 x 50 101.6 1.9
1 1/4 x 1/2 2.06 .44 4 x 3 1/2 4.38 4.2
32 x 15 52.3 .20 100 x 90 111.3 1.9
1 1/2 x 1 1/4 2.31 .70 4 x 3 4.38 3.9
40 x 32 58.7 .32 100 x 80 111.3 1.8
1 1/2 x 1 2.31 .62 4 x 2 1/2 4.38 3.7
40 x 25 58.7 .28 100 x 65 111.3 1.7
1 1/2 x 3/4 2.31 .59 4 x 2 4.38 3.6
40 x 20 58.7 .27 100 x 50 111.3 1.6
1 1/2 x 1/2 2.31 .55 4 x 1 1/2 4.38 3.3
40 x 15 58.7 .25 100 x 40 111.3 1.5
2 x 1 1/2 2.81 1.0
50 x 40 71.4 .46
2 x 1 1/4 2.81 .97
50 x 32 7.14 .44
• 10 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 150Malleable Iron
THREADEDFITTINGSASTM A197
*UNIONS CAPS (ANSI B16.3) FLOOR FLANGES
Size
NPS
DN LH
MINApprox.Weight
1/4 1.32 .20 1/8 .53 .04 1/4 2.62 .24
6 33.5 .09 3 13.5 .02 6 66.5 .11
3/8 1.52 .31 1/4 .63 .04 3/8 2.94 .37
10 38.5 .14 6 16.0 .02 10 74.7 .17
1/2 1.59 .42 3/8 .74 .09 1/2 3.0 .57
15 40.5 .19 10 18.8 .04 15 76 .26
3/4 1.91 .56 1/2 .87 .11 3/4 3.3 .68
20 48.5 .27 15 22.1 .05 20 85 .31
1 2.11 .93 3/4 .97 .18 1 3.8 .82
25 53.5 .42 20 24.6 .08 25 95 .37
1 1/4 2.32 1.3 1 1.16 .31 1 1/4 4.1 1.2
32 59.0 .57 25 29.5 .14 32 105 .54
1 1/2 2.58 1.7 1 1/4 1.28 .53 1 1/2 4.5 1.5
40 65.5 .78 32 32.5 .24 40 115 .66
2 2.85 2.6 1 1/2 1.33 .57 2 5.1 2.1
50 72.5 1.2 40 33.8 .26 50 130 .96
2 1/2 3.29 4.6 2 1.45 .88 2 1/2 6.75 2.6
65 83.5 2.1 50 36.8 .40 65 171.5 1.1
3 3.66 5.7 2 1/2 1.70 1.5 3 7.00 3.8
80 93.0 2.6 65 43.2 .70 80 177.8 1.72
4 4.51 10.1 3 1.80 1.9
100 114.5 4.6 80 45.7 .86
3 1/2 1.90 -
90 48.3 -
4 2.08 3.5
100 52.8 1.6
5 2.32 -
125 58.9 -
6 2.55 7.3
150 64.8 3.29
Size
NPS
DNApprox.Weight D
Size
NPS
DNApprox.Weight
*Sizes 1" through 4" (DN 25 thru 100)conform to ASME/ANSI B16.39.
• 11 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
MALLEABLE IRONTHREADED FITTINGS
ASTM A197HEX HEAD BUSHINGS HEX HEAD BUSHINGS SQUARE HEAD PLUGS
Size
NPS
DNApprox.Weight
Size
NPS
DNApprox.Weight
Size
NPS
DNApprox.Weight
*Sizes NPS 1/8 & 1/4 (DN 3 & 6) are solid, all other sizes cored.
1/4 x 1/8 .02 2 x 1 .81 *1/8 .026 x 3 .01 50 x 25 .37 3 .01
3/8 x 1/8 .02 2 x 1 1/2 .70 *1/4 .0210 x 3 .01 50 x 40 .32 6 .01
3/8 x 1/4 .04 2 1/2 x 1 1.5 3/8 .0410 x 6 .02 65 x 25 .70 10 .02
1/2 x 1/8 .09 2 1/2 x 1 1/4 1.5 1/2 .0915 x 3 .04 65 x 32 .67 15 .04
1/2 x 1/4 .07 2 1/2 x 1 1/2 1.3 3/4 .1115 x 6 .03 65 x 40 .58 20 .05
1/2 x 3/8 .07 2 1/2 x 2 1.1 1 .1515 x 10 .03 65 x 50 .49 25 .07
3/4 x 1/8 .15 3 x 1 2.2 1 1/4 .262 x 3 .07 80 x 25 1.0 32 .13
3/4 x 1/4 .15 3 x 1 1/4 2.2 1 1/2 .3520 x 6 .07 80 x 32 .99 40 .16
3/4 x 3/8 .13 3 x 1 1/2 2.2 2 .5520 x 10 .06 80 x 40 .99 50 .26
3/4 x 1/2 .11 3 x 2 2.0 2 1/2 .9720 x 15 .05 80 x 50 .91 65 .44
1 x 1/4 .26 3 x 2 1/2 1.5 3 1.425 x 6 .12 80 x 65 .66 80 .63
1 x 3/8 .24 4 x 1 4.0 3 1/2 2.52 x 10 .11 100 x 25 1.8 90 1.1
1 x 1/2 .22 4 x 1 1/4 4.0 4 2.525 x 15 .10 100 x 32 1.8 100 1.1
1 x 3/4 .20 4 x 1 1/2 4.0 5 5.425 x 20 .09 100 x 40 1.8 125 2.4
1 1/4 x 1/2 .37 4 x 2 3.7 6 7.532 x 15 .17 100 x 50 1.7 150 3.4
1 1/4 x 3/4 .35 4 x 2 1/2 3.332 x 20 .16 100 x 65 1.5
1 1/4 x 1 .29 4 x 3 3.132 x 25 .13 100 x 80 1.4
1 1/2 x 3/4 .5340 x 20 .24
1 1/2 x 1 .4940 x 25 .22
1 1/2 x 1 1/4 .3140 x 32 .14
2 x 1/2 .8450 x 15 .38
2 x 3/4 .8650 x 20 .39
• 12 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 300Malleable IronTHREADEDFITTINGSASME/ANSI B16.3ASTM A197
45˚ ELBOWS 90˚ ELBOWS TEES
Size
NPS
DN C AApprox.Weight
1/4 .81 .19 1/4 .94 .19 1/4 .94 .29
6 20.6 .09 6 23.9 .09 6 23.9 .13
3/8 .88 .28 3 1.06 .29 3/8 1.06 .42
10 22.4 .13 10 26.9 .13 10 26.9 .19
1/2 1.00 .44 1/2 1.25 .50 1/2 1.25 .72
15 25.4 .20 15 31.8 .23 15 31.8 .33
3/4 1.13 .70 3/4 1.44 .77 3/4 1.44 1.1
20 28.7 .32 20 36.6 .35 20 36.6 .50
1 1.31 1.1 1 1.63 1.2 1 1.63 1.7
25 33.3 .50 25 41.4 .53 25 41.4 .75
1 1/4 1.50 1.7 1 1/4 1.94 1.8 1 1/4 1.94 2.6
32 38.1 .75 32 49.3 .82 32 49.3 1.17
1 1/2 1.69 2.2 1 1/2 2.13 2.4 1 1/2 2.13 3.4
40 42.9 1.01 40 54.1 1.10 40 54.1 1.54
2 2.00 3.4 2 2.50 3.8 2 2.50 5.3
50 50.8 1.6 50 63.5 1.75 50 63.5 2.40
2 1/2 2.25 5.6 2 1/2 2.94 6.3 2 1/2 2.94 8.4
65 57.2 2.5 65 74.7 2.9 65 74.7 3.8
3 2.50 8.3 3 3.38 9.5 3 3.38 12.8
80 63.5 3.8 80 85.9 4.3 80 85.9 5.8
Size
NPS
DNApprox.Weight A
Size
NPS
DNApprox.Weight
• 13 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 300Malleable Iron Threaded
COUPLINGSASME/ANSI B16.3
ASTM A197COUPLINGS REDUCING COUPLINGS
Size
NPS
DN W
Dimension
Approx.Weight
Size
NPS
DN M
Dimensions
Approx.Weight
1/4 1.37 .17 3/4 x 1/2 1.75 .55
6 35.1 .08 20 x 15 44.5 .25
3/8 1.62 .26 1 x 3/4 2.00 .83
10 41.4 .12 25 x 20 50.8 .38
1/2 1.87 .44 1 x 1/2 2.00 .77
15 47.8 .20 25 x 15 50.8 .35
3/4 2.12 .72 1 1/4 x 1 2.38 1.3
20 54.1 .33 32 x 25 60.5 .57
1 2.37 1.1 1 1/2 x 1 1/4 2.69 1.8
25 60.5 .48 40 x 32 68.3 .82
1 1/4 2.87 2.87 2 x 1 1/2 3.19 2.8
32 73.2 .76 50 x 40 81.0 1.25
1 1/2 2.87 2.1 2 1/2 x 2 3.69 4.5
40 73.2 .96 65 x 50 93.7 2.0
2 3.62 3.5 3 x 2 1/2 4.06 6.3
50 92.2 1.59 80 x 65 103.1 2.9
2 1/2 4.12 5.4
65 104.9 2.4
3 4.12 7.4
80 104.9 3.6
• 14 •
INCHES
MILLIMETRES
POUNDS
KILOGRAMS
CLASS 300Malleable IronTHREADED FITTINGSASTM A197
UNIONS (ANSI B16.39) CAPS (ANSI B16.3)
Size
NPS
DN L
Dimension
Approx.Weight
Size
NPS
DN H MIN.
Dimensions
Approx.Weight
1/2 2.09 .64 1/2 .98 .26
15 .53 .29 15 24.9 .12
3/4 2.23 .97 3/4 1.08 .39
20 56.6 .44 20 27.4 .18
1 2.49 1.5 1 1.26 .62
25 63.2 .68 25 32.0 .28
1 1/4 2.72 2.2 1 1/4 1.38 .98
32 .69 1.0 32 35.1 .44
1 1/2 2.95 2.6 1 1/2 1.43 1.32
40 .75 1.20 40 36.3 .60
2 3.44 4.2 2 1.68 1.91
50 87.3 1.92 50 42.7 .87
2 1/2 3.89 7.3
65 98.8 3.3
3 4.24 10.5
80 107.8 4.8
UNION CAP
• 15 •
• 16 •
CATALOGUE SECTION 7Although great care has been taken in compiling the informationcontained in this catalogue, CCTF does not accept responsibility for theconsequences of any errors, nor for the effects of any subsequentchanges made by the various sources of data.
MITF