B 13.MAY.2014 RE-ISSUED FOR APPROVAL M.S KANG S.I LEE H.S SHIN
A 20.NOV.2013 ISSUED FOR APPROVAL M.S KANG S.I LEE H.S SHIN
REV. DATE DESCRIPTION DESIGNED CHECKED APPROVED
OWNER
PROJECT
SHUQAIQ STEAM POWER PLANT
ENGINEER
CONTRACTOR
SUBCONTRACTOR VENDOR INTERNAL DOC.NO
N/A N/A
THIS DOCUMENT IS NOT TO BE USED FOR CONSTRUCTION OR FOR ORDERING MATERIAL UNTIL CERTIFIED AND DATED.THE CONTRACTOR HHI CONFIRMS FULLY COMPLIANCE WITH THE O/E’S COMMENTS. NO OTHER CHANGES HAD BEEN MADE ON THE DOCUMENT. THE CONTRACTOR MAY SUBMIT THE DOCUMENTS AS “FOR CONSTRUCTION”
APPROVAL/CERTIFICATION INFORMATION DOC. NO : REV. NO : DATE : STATUS:
DOCUMENT TITLE
PIPING MATERIAL SPECIFICATION
CONTRACT NO. DOCUMENT NO NO. OF PAGES REV.
31221097/00 S-00-TAA-P-38-002-001 174 B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
2/174
TABLE OF CONTENTS
1. General .......................................................................................................................................... 3
1.1 Intent ................................................................................................................................................ 3
1.2 Scope ................................................................................................................................................. 3
2. References ..................................................................................................................................... 3
2.1 Codes and Standards ...................................................................................................................... 3
2.2 Project Specification ....................................................................................................................... 5
3. Material Requirements .............................................................................................................. 15
3.1 Pipes ............................................................................................................................................... 15
3.2 Fittings ........................................................................................................................................... 15
3.3 Flanges ........................................................................................................................................... 16
3.4 Gaskets ........................................................................................................................................... 16
3.5 Bolts and Nuts for line flange ....................................................................................................... 17
3.6 Valves .............................................................................................................................................. 17
4. Miscellaneous Requirements ..................................................................................................... 19
5. Abbreviation ............................................................................................................................... 20
6. Numbering System for Piping Class ........................................................................................ 22
7. Numbering System for Valve’s Material Code ........................................................................ 23
Attachment – 1 : Index of Piping Material Classification .......................................................... 26
Attachment – 2 : Piping Material Class Sheets ........................................................................... 39
Attachment – 3 : Piping Branch Table ....................................................................................... 156
Attachment – 4 : Data Sheet for Manual Valves ....................................................................... 158
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
3/174
1. General
1.1 Intent
This specification defines, by Piping Class, the material requirement for pipes, fittings, flanges, valves and all other piping components for each noted service and the pressure/temperature limitations within which they may be employed for Shuqaiq Steam Power Plant Project.
1.2 Scope
1) This specification shall be applied to piping materials indicated on P&ID flow diagrams, utility flow diagrams and the other piping drawings.
2) When the piping is connected to equipment, this specification shall be applied to the extent indicated below. (1) Companion flanges, gaskets, bolts and nuts at the equipment nozzle. (2) First block valve with companion flanges, gaskets, bolts and nuts in the instrument connecting line. (3) Companion flanges, gaskets, bolts and nuts for relief valves. (4) Companion flanges, gaskets, bolts and nuts at the matching point between the piping furnished as
a part of equipment by its manufacturer and that provided by purchaser.
3) This specification shall not be applied to followings. (1) Specially designed companion flanges, gaskets, bolts and nuts at the equipment nozzle. (2) Boiler Internal Piping
(Refer to ASME Code Calculation for Boiler Pressure Part, Doc No.”S-04-HAD-M-47-001-001”) (3) Plumbing piping for building (4) Civil drainage piping
2. References
2.1 Codes and Standards
Design, fabrication, testing and inspection of piping materials shall be accomplished in accordance with the applicable Codes and Standards as follows:
American Society of Mechanical Engineering
Code and Standard Version Description
- ASME B1.1 2008 Unified Inch Screw Threads (UN and UNR Thread Form)
- ASME B1.20.1 2006 Pipe Threads, General Purpose
- ASME B16.5 2009 Pipe Flanges and Flanged Fittings
- ASME B16.9 2007 Factory-made Wrought Butt welding Fittings
- ASME B16.10 2009 Face-to-Face and End-to-End Dimensions Valves
- ASME B16.11 2011 Forged Fittings, Socket-Welding and Threaded
- ASME B16.20 2007 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
4/174
- ASME B16.21 2011 Nonmetallic Flat Gaskets for Pipe Flanges
- ASME B16.25 2012 Butt welding Ends
- ASME B16.28 1994 Wrought Steel Butt welding Short Radius Elbows and Returns
- ASME B16.34 2013 Valves - Flanged, Threaded, and Welding End
- ASME B16.47 2011 Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric/Inch Standard
- ASME B16.48 2010 Line Blanks
- ASME B18.2.1 2012 Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex Flange, Lobed Head, and Lag Screws (Inch Series)
- ASME B18.2.2 2010 Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange, and Coupling Nuts (Inch Series)
- ASME B31.1 2012 Power Piping
- ASME B31.3 2012 Process Piping
- ASME SEC I 2011 Rules For Construction of Power Boiler
- ASME SEC II 2011 Material Part
- ASME B36.10M 2010 Welded and Seamless Wrought Steel Pipe
- ASME B36.19M 2010 Stainless Steel Pipe
American Petroleum Institute
- API 5L 2012 Line Pipe
- API 590 1985 Steel Line blanks
- API 594 2010 Check Valves: Flanged, Lug, Wafer and Butt-welding
- API 598 2009 Valve Inspection and Testing
- API 6D 2008 Pipeline Valves
- API 600 2009 Bolted Bonnet Steel Gate Valves for Petroleum and Natural Gas Industries
- API 602 2009 Steel Gate, Globe and Check Valves for Sizes DN 100 and Smaller for the Petroleum and Natural Gas Industries
- API 607 2010 Testing of Valves - Fire Type-testing Requirements
- API 609 2009 Butterfly Valves: Double Flanged, Lug- and Wafer-Type
Manufactures Standardization Society
- MSS SP- 6 2012 Standard Finishes for Contact Faces of Pipe Flanges and Connecting-End Flanges of Valves and Fittings
- MSS SP-25 2008 Standard Marking System for Valves, Fittings, Flanges and Unions
- MSS SP-43 2008 Wrought Stainless Steel Butt-Welding Fittings
- MSS SP-55 2011 Quality Standard for Steel Castings for Valves, Flanges, Fittings and Other Piping Components
- MSS SP-58 2009 Pipe Hangers and Supports - Materials, Design and Manufacture
- MSS SP-61 2009 Pressure Testing of Steel Valves
- MSS SP-80 2008 Bronze Gate, Globe, Angle and Check Valves B
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
5/174
- MSS SP-97 2012 Integrally Reinforced Forged Branch Outlet Fittings - Socket Welding, Threaded and Butt welding Ends
National Fire Protection Association
- NFPA 24 2013 Standards for the installation of Private Fire Service Mains and Their Appurtenances
American Water Works Association
- AWWA C207 2007 American Water Works Association Standard for Steel Pipe Flanges for Water Work Service – sizes 4 in. (DN100) Through 144 in (DN3600)
- AWWA C208 2012 Dimensions for Fabricated Steel Water Pipe Fittings
- AWWA C301 2007 Pre-stressed Concrete Pressure Pipe, Steel Cylinder Type, for Water and Other Liquids
- AWWA C304 2007 Design of Pre-stressed Concrete Cylinder Pipe
- AWWA C504 2010 Rubber-Seated Butterfly Valves
- AWWA C516 2010 Large Diameter Rubber-Seated Butterfly Valves, Sizes 78in and Larger
- AWWA C950 2007 Fiberglass Pressure Pipe
- AWWA M45 2005 Fiberglass Pipe Design
Pipe Fabrication Institute
- PFI ES-3 2004 Fabricating Tolerances
- PFI ES-24 2004 Pipe bending methods, tolerances, process and material requirements
International Organization of Standardization
- ISO 5752 1982 Metal valves for use in flanged pipe systems - face to face and centre to face dimensions
- ISO 1461 2009 Hot Dip Galvanized Coatings on Fabricated Iron and Steel Articles – Specifications and Test Methods
- ISO 80000-1 2009 Quantities and units
Euro norm Standards (EN)
- EN 10204 2004 Materials Testing Certificates
1) Material specification referenced is ASTM/ASME unless otherwise noted.
2) Unless otherwise indicated, all material classes are in accordance with the requirements of the ASME Code for power piping B31.1 except GRP piping and miter fitting. GRP piping shall comply in accordance with ASME B31.3, AWWA C950 & AWWA M45. Miter fitting shall comply in accordance with ASME B31.3 Para .304.2.
2.2 Project Specification
Piping Specification
Doc No. Description
S-00-TAA-P-38-001-001 Piping Design Criteria B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
6/174
S-00-TAA-P-38-003-001 Piping Insulation Specification
S-00-TAA-P-71-001-001 Calculation For Pipe Wall Thickness
S-00-TAA-P-46-003-001 Rubber Lining Procedure For Internal Steel Pipe
S-00-TAA-P-46-004-001 3 Layer PE Coating Specification and Procedure for External Surface of Steel Pipe
S-00-TBB-T-32-001-001 Painting Specification
S-00-TAA-P-65-001-001 Line List
S-00-TAA-P-61-001-001 Valve List
Process Flow Diagram
Doc. No. Description
S-00-EG_-S-12-001-001 Fuel Oil System (HFO/HCO) (1/4)
S-00-EG_-S-12-001-002 Fuel Oil System (HFO/HCO) (2/4)
S-00-EG_-S-12-001-003 Fuel Oil System (HFO/HCO) (3/4)
S-00-EG_-S-12-001-004 Fuel Oil System (HFO/HCO) (4/4)
S-00-EG_-S-12-002-001 Distillate Oil System
S-00-ET_-S-12-101-001 Off-Site Ash Dumping System
S-00-GC_-S-12-001-001 Demineralized Water Treatment System (1/4)
S-00-GC_-S-12-001-002 Demineralized Water Treatment System (2/4)
S-00-GC_-S-12-001-003 Demineralized Water Treatment System (3/4)
S-00-GC_-S-12-001-004 Demineralized Water Treatment System (4/4)
S-00-GD_-S-12-001-001 Desalination System
S-00-GH_-S-12-001-001 Demineralized Make-Up Water System
S-00-GH_-S-12-002-001 Service Water System
S-00-GK_-S-12-001-001 Potable Water System
S-00-GN_-S-12-001-001 Chemical Waste Water Treatment System
S-00-GN_-S-12-002-001 Oily Water Treatment System
S-00-GN_-S-12-003-001 Dirty Drain Treatment System
S-00-GR_-S-12-001-001 Sewage Treatment System
S-00-LD_-S-12-001-001 Condensate Polishing System (Regeneration System)
S-00-MA_-S-12-002-001 Auxiliary Steam System
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
7/174
S-00-NA_-S-12-001-001 Steam Transformer System
S-00-PA_-S-12-001-001 Circulating Water System
S-00-PB_-S-12-001-001 Electrochlorination System
S-00-PG_-S-12-001-001 Closed Circuit Cooling Water (For Common Equipment)
S-00-QE_-S-12-001-001 Compressed Air System (1/2)
S-00-QE_-S-12-001-002 Compressed Air System (2/2)
S-00-QK_-S-12-001-001 Chilled Water System
S-01-HA_-S-12-001-001 Boiler Air And Gas System
S-01-LA_-S-12-001-001 Feedwater System
S-01-LB_-S-12-001-001 Feedwater Heater Extraction Steam System
S-01-LC_-S-12-001-001 Feedwater Heater Drain System
S-01-LC_-S-12-002-001 Condensate System
S-01-LD_-S-12-001-001 Condensate Polishing System (Unit 11 Polisher)
S-01-MA_-S-12-001-001 Main And Reheat Steam System
S-01-PG_-S-12-001-001 Closed Circuit Cooling Water System (For Unit 11)
Piping and Instrumentation Diagram
Doc No Description
S-00-EG_-S-20-001-001 Fuel Oil System (HFO/HCO Unloading Terminal) (1/12)
S-00-EG_-S-20-001-002 Fuel Oil System (HFO/HCO Metering System) (2/12)
S-00-EG_-S-20-001-003 Fuel Oil System (HFO/HCO Storage System) (3/12)
S-00-EG_-S-20-001-004 Fuel Oil System (HFO/HCO Ring Main) (4/12)
S-01-EG_-S-20-001-005 Fuel Oil System (Main Fuel Oil Pumping) (5/12)
S-01-EG_-S-20-001-007 Fuel Oil System (HFO Heating System) (6/12)
S-00-EG_-S-20-001-008 Fuel Oil System (HFO/HCO Return Line Header) (7/12)
S-00-EG_-S-20-001-009 Fuel Oil System HFO/HCO Forward and Return) (8/12)
S-00-EG_-S-20-001-011 Fuel Oil System (HFO/HCO Storage Tank Heating System) (9/12)
S-00-EG_-S-20-001-012 Fuel Oil System (HFO/HCO Transfer System) (10/12)
S-00-EG_-S-20-001-013 Fuel Oil System (HFO/HCO Drain System 1) (11/12)
S-00-EG_-S-20-001-015 Fuel Oil System (HFO/HCO Drain System 2) (12/12)
S-00-EG_-S-20-002-001 Distillate Oil System (DFO Unloading Station) (1/7)
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
8/174
S-00-EG_-S-20-002-002 Distillate Oil System (DFO Storage System) (2/7)
S-00-EG_-S-20-002-003 Distillate Oil System (DFO Forwarding System) (3/7)
S-00-EG_-S-20-002-004 Distillate Oil System (DFO Transfer System) (4/7)
S-00-EG_-S-20-002-005 Distillate Oil System (DFO Drain System) (5/7)
S-00-EG_-S-20-002-006 Distillate Oil System (Fuel Additive System) (6/7)
S-00-EG_-S-20-002-007 Distillate Oil System (Fuel Additive System) (7/7)
S-00-ET_-S-20-001-001 Ash Collection and Handling System (1/10)
S-00-ET_-S-20-001-002 Ash Collection and Handling System (2/10)
S-00-ET_-S-20-001-003 Ash Collection and Handling System (3/10)
S-00-ET_-S-20-001-004 Ash Collection and Handling System (4/10)
S-00-ET_-S-20-001-005 Ash Collection and Handling System (5/10)
S-00-ET_-S-20-001-006 Ash Collection and Handling System (6/10)
S-00-ET_-S-20-001-007 Ash Collection and Handling System (7/10)
S-00-ET_-S-20-001-008 Ash Collection and Handling System (8/10)
S-00-ET_-S-20-001-009 Ash Collection and Handling System (9/10)
S-00-ET_-S-20-001-010 Ash Collection and Handling System (10/10)
S-00-ET_-S-20-002-001 Off-Site Ash Dumping System (1/4)
S-00-ET_-S-20-002-002 Off-Site Ash Dumping System (2/4)
S-00-ET_-S-20-002-003 Off-Site Ash Dumping System (3/4)
S-00-ET_-S-20-002-004 Off-Site Ash Dumping System (4/4)
S-00-GC_-S-20-001-001 Demineralized Water Treatment System (BWRO HP Pump) (1/5)
S-00-GC_-S-20-001-002 Demineralized Water Treatment System (BWRO Unit) (2/5)
S-00-GC_-S-20-001-003 Demineralized Water Treatment System (CEDI Unit) (3/5)
S-00-GC_-S-20-001-004 Demineralized Water Treatment System (GTMDO Unit) (4/5)
S-00-GC_-S-20-001-005 Demineralized Water Treatment System (CIP Tank and Pump) (5/5)
S-00-GD_-S-20-001-001 Desalination System (Dissolved Air Flotation Unit) (1/12)
S-00-GD_-S-20-001-002 Desalination System (Ultra Filter Unit) (2/12)
S-00-GD_-S-20-001-003 Desalination System (Filtered Water Tank) (3/12)
S-00-GD_-S-20-001-004 Desalination System (SBS/Anti Scalant Dosing) (4/12)
S-00-GD_-S-20-001-005 Desalination System (1st SWRO HP Pump) (5/12)
S-00-GD_-S-20-001-006 Desalination System (1st SWRO Unit) (6/12)
S-00-GD_-S-20-001-007 Desalination System (2nd SWRO Unit) (7/12)
S-00-GD_-S-20-001-008 Desalination System (Desal. Water Tank) (8/12)
S-00-GD_-S-20-001-009 Desalination System (CIP Tank and Pump) (9/12)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
9/174
S-00-GD_-S-20-001-010 Desalination System (10/12)
S-00-GD_-S-20-001-011 Desalination System (Acid Dosing System) (11/12)
S-00-GD_-S-20-001-012 Desalination System (Caustic Dosing System) (12/12)
S-00-GH_-S-20-001-001 Demineralized Make-up Water System (Demi. Water Tank) (1/2)
S-00-GH_-S-20-001-002 Demineralized Make-up Water System (Make-up Water Distribution) (2/2)
S-00-GH_-S-20-002-001 Service Water System (Service and Fire Water Tank) (1/3)
S-00-GH_-S-20-002-002 Service Water System (Service Water Distribution) (2/3)
S-00-GH_-S-20-002-003 Service Water System (Service Water Distribution) (3/3)
S-00-GK_-S-20-001-001 Potable Water System (Main Potable Water Tower) (1/2)
S-00-GK_-S-20-001-002 Potable Water System (Potable Water Distribution) (2/2)
S-00-GM_-S-20-001-001 Chemical Waste Water Collection System (1/3)
S-00-GM_-S-20-001-002 Chemical Waste Water Collection System (2/3)
S-00-GM_-S-20-001-003 Chemical Waste Water Collection System (3/3)
S-00-GM_-S-20-002-001 Oily Water Collection System (1/3)
S-00-GM_-S-20-002-002 Oily Water Collection System (2/3)
S-00-GM_-S-20-002-003 Oily Water Collection System (3/3)
S-00-GM_-S-20-003-001 Dirty Drain Collection System
S-00-GM_-S-20-004-001 Clean Drain Collection System (1/2)
S-00-GM_-S-20-004-002 Clean Drain Collection System (2/2)
S-00-GN_-S-20-001-001 Chemical Waste Water Treatment System (1/2)
S-00-GN_-S-20-001-002 Chemical Waste Water Treatment System (2/2)
S-00-GN_-S-20-002-001 Oily Water Treatment System
S-00-GN_-S-20-003-001 Dirty Drain Treatment System
S-00-GQ_-S-20-001-001 Sewage Collection System (1/2)
S-00-GQ_-S-20-001-002 Sewage Collection System (2/2)
S-00-GR_-S-20-001-001 Sewage Treatment System (1/2)
S-00-GR_-S-20-001-002 Sewage Treatment System (2/2)
S-00-HS_-S-20-003-003 Urea Supply System(3/3)
S-00-LD_-S-20-001-001 Condensate Polishing System (Conesep Regeneration Station A) (1/9)
S-00-LD_-S-20-001-002 Condensate Polishing System (Conesep Regeneration Station B) (2/9)
S-00-LD_-S-20-001-003 Condensate Polishing System (Acid Dosing System) (3/9)
S-00-LD_-S-20-001-004 Condensate Polishing System (Caustic Dosing System) (4/9)
S-00-LD_-S-20-001-005 Condensate Polishing System (Regen. Blowers) (5/9)
S-00-LD_-S-20-001-006 Condensate Polishing System (Hot Water Tank) (6/9)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
10/174
S-00-LD_-S-20-001-007 Condensate Polishing System (Acid Storage Tank) (7/9)
S-00-LD_-S-20-001-008 Condensate Polishing System (Caustic Storage Tank) (8/9)
S-00-LD_-S-20-001-009 Condensate Polishing System (Instrument Air For Regen Area) (9/9)
S-00-MA_-S-20-003-002 Plant Common Auxiliary Steam System
S-00-MA_-S-20-004-001 Dirty And Clean Oil System
S-00-NA_-S-20-001-001 Steam Transformer System - Steam Transformers
S-00-NA_-S-20-001-002 Steam Transformer System - Secondary Recovered Condensate Tank
S-00-NA_-S-20-001-003 Steam Transformer System - Secondary Steam Supply & Condensate Return (1/3)
S-00-NA_-S-20-001-004 Steam Transformer System - Secondary Steam Supply & Condensate Return (2/3)
S-00-NA_-S-20-001-005 Steam Transformer System - Secondary Steam Supply & Condensate Return (3/3)
S-00-PA_-S-20-001-001 Circulating Water System (1/11) - Unit 13/ 14 Circulating Water Pump
S-00-PA_-S-20-001-002 Circulating Water System (2/11) - Unit 11/ 12 Circulating Water Pump
S-01-PA_-S-20-001-003 Circulating Water System (3/11) - Booster Pump For CW Pump
S-00-PA_-S-20-001-004 Circulating Water System (4/11) - FGD Supplementary Seawater Pump
S-00-PA_-S-20-001-005 Circulating Water System (5/11) - Aux. Seawater Supply Pump
S-00-PA_-S-20-001-006 Circulating Water System (6/11) - Aux. Seawater Supply Pump
S-00-PA_-S-20-001-007 Circulating Water System (7/11) - Aux. Seawater Supply Pump
S-01-PA_-S-20-001-008 Circulating Water System (8/11) - Condenser Shell A
S-01-PA_-S-20-001-009 Circulating Water System (9/11) - Condenser Shell B
S-01-PA_-S-20-001-010 Circulating Water System (10/11) - Tube Cleaning System
S-00-PA_-S-20-001-011 Circulating Water System (11/11) - Discharge Culvert & Channel
S-00-PB_-S-20-001-001 Sea Water Intake Screen System (1/4) - Auto Self Cleaning Strainer
S-00-PB_-S-20-001-002 Sea Water Intake Screen System (2/4) - Bar Screen/ Drum Screen
S-00-PB_-S-20-001-003 Sea Water Intake Screen System (3/4) - Bar Screen/ Drum Screen
S-00-PB_-S-20-001-004 Sea Water Intake Screen System (4/4) - Bar Screen/ Drum Screen
S-00-PB_-S-20-002-001 Electrochlorination System (1/9) (Auto Self Cleaning Strainer)
S-00-PB_-S-20-002-002 Electrochlorination System (2/9) (Hypochlorite Generator)
S-00-PB_-S-20-002-003 Electrochlorination System (3/9) (Hypochlorite Generator Unit)
S-00-PB_-S-20-002-004 Electrochlorination System (4/9) (Hypochlorite Tank & Blower)
S-00-PB_-S-20-002-005 Electrochlorination System (5/9) (Hypochlorite Dosing Pump)
S-00-PB_-S-20-002-006 Electrochlorination System (6/9) (Intake Pipe Dosing Line)
S-00-PB_-S-20-002-007 Electrochlorination System (7/9) (Intake Pipe Dosing Line)
S-00-PB_-S-20-002-008 Electrochlorination System (8/9) (Bar Screen Dosing Line)
S-00-PB_-S-20-002-012 Electrochlorination System (9/9) - Acid Flushing System
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
11/174
S-00-QC_-S-20-001-003 PSA Oxygen Generation & Distribution System
S-00-QC_-S-20-001-004 Centralized Ammonia Storage And Transfer System
S-00-QC_-S-20-002-001 Steam Transformer Chemical Dosing System
S-00-QC_-S-20-003-001 Boiler Water Wash Chemical Dosing System
S-00-QC_-S-20-004-001 Auxiliary Boiler Chemical Dosing System
S-00-QE_-S-20-001-001 Compressed Air System (1/9)
S-00-QE_-S-20-001-002 Compressed Air System (2/9)
S-00-QE_-S-20-001-003 Compressed Air System (3/9)
S-00-QE_-S-20-001-004 Compressed Air System (4/9)
S-00-QE_-S-20-001-006 Compressed Air System (6/9)
S-00-QE_-S-20-001-007 Compressed Air System (7/9)
S-00-QE_-S-20-001-008 Compressed Air System (8/9)
S-00-QE_-S-20-001-009 Compressed Air System (9/9)
S-00-QH_-S-20-001-001 Auxiliary Boiler System
S-00-QJ_-S-20-001-001 N2 Gas Distribution System
S-00-QJ_-S-20-002-001 Hydrogen Generation System (1/2)
S-00-QJ_-S-20-002-002 H2 Gas Distribution System (1/2)
S-00-QJ_-S-20-002-003 Hydrogen Generation System (2/2)
S-00-QJ_-S-20-004-001 Nitrogen Generator System For Demineralized Water System
S-00-QK_-S-20-001-001 Chilled Water System (1/3)
S-00-QK_-S-20-001-002 Chilled Water System (2/3)
S-00-QK_-S-20-001-003 Chilled Water System (3/3)
S-00-QU_-S-20-002-001 Auxiliary Boiler Sampling System
S-01-HA_-S-20-001-001 Boiler Water System (1/4)
S-01-HA_-S-20-001-002 Boiler Water System (2/4)
S-01-HA_-S-20-001-003 Boiler Water System (3/4)
S-01-HA_-S-20-001-004 Boiler Water System (4/4)
S-01-HA_-S-20-002-001 Boiler Steam System (1/2)
S-01-HA_-S-20-002-002 Boiler Steam System (2/2)
S-01-HA_-S-20-003-001 Boiler Reheat System
S-01-HA_-S-20-004-001 Boiler Drain System
S-01-HC_-S-20-001-001 Boiler Sootblowing System
S-01-HC_-S-20-001-002 Boiler Sealing Air System(1/2)
S-01-HC_-S-20-001-003 Boiler Sealing Air System(2/2)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
12/174
S-01-HC_-S-20-002-001 Boiler Water Washing System
S-01-HH_-S-20-001-001 Boiler Burning System(1/5) (D.O For Warm-Up)
S-01-HH_-S-20-001-002 Boiler Burning System(2/5) (Heavy Fuel Oil)
S-01-HH_-S-20-001-004 Boiler Burning System(3/5) (Burner Unit)
S-01-HH_-S-20-001-005 Boiler Burning System(4/5) (Ignitor Unit)
S-01-HH_-S-20-001-006 Boiler Burning System(5/5) (Burner Detail)
S-01-HH_-S-20-001-007 Boiler Oily Water Drain System
S-01-HL_-S-20-001-001 Boiler Combustion Air System(1/2)
S-01-HL_-S-20-001-002 Boiler Combustion Air System(2/2)
S-01-HL_-S-20-002-001 Boiler Steam Air Heater System(1/2)
S-01-HL_-S-20-002-002 Boiler Steam Air Heater System(2/2)
S-01-HN_-S-20-001-001 Boiler Flue Gas System(1/2)
S-01-HN_-S-20-001-002 Boiler Flue Gas System(2/2)
S-01-HN_-S-20-002-001 Boiler Instrumentation
S-01-HS_-S-20-001-001 Flue Gas Selective Catalytic Reduction System(1/2)
S-01-HS_-S-20-001-002 Flue Gas Selective Catalytic Reduction System(2/2)
S-01-HS_-S-20-002-001 Urea Dissolver System(1/2)
S-01-HS_-S-20-003-001 Urea Supply System(1/3)
S-01-HT_-S-20-001-001 Flue Gas Desulphurization System(1/6)
S-01-HT_-S-20-001-002 Flue Gas Desulphurization System(2/6)
S-01-HT_-S-20-001-003 Flue Gas Desulphurization System(3/6)
S-01-HT_-S-20-001-004 Flue Gas Desulphurization System(4/6)
S-01-HT_-S-20-001-005 Flue Gas Desulphurization System(5/6)
S-01-HT_-S-20-001-006 Flue Gas Desulphurization System(6/6)
S-01-HX_-S-20-001-001 Boiler Compressed Air System(1/3)
S-01-HX_-S-20-001-002 Boiler Compressed Air System(2/3)
S-01-HX_-S-20-001-003 Boiler Compressed Air System(3/3)
S-01-HX_-S-20-002-001 Boiler Utility System
S-01-LA_-S-20-001-001 Feedwater System (1/3) - Deaerator
S-01-LA_-S-20-001-002 Feedwater System (2/3) - BFP
S-01-LA_-S-20-001-003 Feedwater System (3/3) - HP Feedwater Heaters
S-01-LB_-S-20-001-001 Feedwater Heater Extraction Steam System (1/2)
S-01-LB_-S-20-001-002 Feedwater Heater Extraction Steam System (2/2)
S-01-LB_-S-20-002-001 Feedwater Heater Miscellaneous System (1/2)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
13/174
S-01-LB_-S-20-002-002 Feedwater Heater Miscellaneous System (2/2)
S-01-LC_-S-20-001-001 Feedwater Heater Drain System (1/3)
S-01-LC_-S-20-001-002 Feedwater Heater Drain System (2/3)
S-01-LC_-S-20-001-003 Feedwater Heater Drain System (3/3)
S-01-LC_-S-20-002-001 Condensate System (1/11) - Condenser A
S-01-LC_-S-20-002-002 Condensate System (2/11) - Condenser B
S-01-LC_-S-20-002-003 Condensate System (3/11) - CEP
S-01-LC_-S-20-002-004 Condensate System (4/11) - Condensate Discharge Header
S-01-LC_-S-20-002-005 Condensate System (5/11) - LP Feedwater Heaters
S-01-LC_-S-20-002-006 Condensate System (6/11) - Drain To Condenser A
S-01-LC_-S-20-002-007 Condensate System (7/11) - Drain To Condenser B
S-01-LC_-S-20-002-008 Condensate System (8/11) - Clean Drain Flash Tank
S-01-LC_-S-20-002-009 Condensate System (9/11) - Steam Drains
S-01-LC_-S-20-002-010 Condensate System (10/11) - Sample Pumps
S-01-LC_-S-20-002-011 Condensate System (11/11) - Condensate Reserve Tank
S-01-LC_-S-20-003-001 Condenser Air Removal System
S-01-LC_-S-20-003-002 Condenser Water Box Priming System
S-01-LD_-S-20-001-001 Condensate Polishing System (Unit11-Mixed Bed 1) (1/3)
S-01-LD_-S-20-001-002 Condensate Polishing System (Unit11-Mixed Bed 2) (2/3)
S-01-LD_-S-20-001-003 Condensate Polishing System (Unit11-Mixed Bed 3) (3/3)
S-01-MA_-S-20-001-001 Main And Reheat Steam System
S-01-MA_-S-20-001-002 Steam Turbine System (1/3)
S-01-MA_-S-20-001-003 Steam Turbine System (2/3)
S-01-MA_-S-20-001-004 Steam Turbine System (3/3)
S-01-MA_-S-20-002-001 HP Bypass Steam System
S-01-MA_-S-20-002-002 LP Bypass Steam System
S-01-MA_-S-20-003-001 Unit Auxiliary Steam System
S-01-MA_-S-20-005-001 Steam Turbine Gland Steam System
S-01-MA_-S-20-005-002 Steam Turbine Drain System
S-01-MA_-S-20-006-001 Steam Turbine Generator Lube Oil Supply System
S-01-MA_-S-20-006-002 Steam Turbine Generator Lube Oil & Jacking Oil System (1/2)
S-01-MA_-S-20-006-003 Steam Turbine Generator Lube Oil & Jacking Oil System (2/2)
S-01-MA_-S-20-007-001 Steam Turbine Governing & Control Oil System
S-01-MK_-S-20-001-001 Steam Turbine Generator H2 & CO2 Gas System
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
14/174
S-01-MK_-S-20-002-001 Steam Turbine Generator Seal Oil System
S-01-MK_-S-20-002-002 Steam Turbine Generator Stator Cooling Water System
S-01-PG_-S-20-001-001 Closed Circuit Cooling Water System (1/9) - Unit #1 CCCW Pump
S-01-PG_-S-20-001-002 Closed Circuit Cooling Water System (2/9) - Unit #1 CCCW Heat Exchanger
S-01-PG_-S-20-001-003 Closed Circuit Cooling Water System (3/9) - Unit #1 CCCW Distribution
S-01-PG_-S-20-001-004 Closed Circuit Cooling Water System (4/9) - Unit #1 CCCW Distribution
S-01-PG_-S-20-001-005 Closed Circuit Cooling Water System (5/9) - Unit #1 CCCW Distribution
S-01-PG_-S-20-001-006 Closed Circuit Cooling Water System (6/9) - Unit #1 CCCW Distribution
S-00-PG_-S-20-001-007 Closed Circuit Cooling Water System (7/9) - For Common Equipment
S-00-PG_-S-20-001-008 Closed Circuit Cooling Water System (8/9) - For Common Equipment
S-00-PG_-S-20-001-009 Closed Circuit Cooling Water System (9/9) - For Common Equipment
S-01-QC_-S-20-001-001 Steam Cycle Chemical Dosing System(1/2)
S-01-QC_-S-20-001-002 Steam Cycle Chemical Dosing System(2/2)
S-01-QE_-S-20-001-005 Compressed Air System (5/9)
S-01-QJ_-S-20-002-001 H2 Gas Distribution System (2/2)
S-01-QJ_-S-20-003-001 CO2 Gas Distribution System
S-01-QU_-S-20-001-001 Sampling System (1/5)
S-01-QU_-S-20-001-002 Sampling System (2/5)
S-01-QU_-S-20-001-003 Sampling System (3/5)
S-01-QU_-S-20-001-004 Sampling System (4/5)
S-01-QU_-S-20-001-005 Sampling System (5/5)
S-03-HS_-S-20-002-002 Urea Dissolver System(2/2)
S-03-HS_-S-20-003-002 Urea Supply System(2/3)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
15/174
3. Material Requirements
3.1 Pipes
1) Dimensions of steel pipes shall be in accordance with the following standards. - Welded and seamless wrought steel pipe : ASME B36.10M - Stainless steel pipe : ASME B36.19M
Non-metal pipe shall be complied with the following relevant code and manufacture standard. - GRP : AWWA C950 and AWWA M45 - HDPE: EN12201 or ISO4427 - CPVC : ASTM F441
2) For steel pipe wall thickness shall be calculated in accordance with section 104.1 ASME B31.1 and section 304.1 ASME B31.3.
For determining wall thickness and stiffening requirements for straight pipe under external pressure, the procedures outlined in UG-28, UG-29 and UG-30 of ASME Sec VIII, Division I.
Non-metal pipe shall be complied with the following relevant code and manufacture standard. - GRP : AWWA C950 and AWWA M45 - HDPE: EN12201 and ISO4427 - CPVC : ASTM F441
3) Wall thickness has been based on the minimum wall thickness required for the design pressure-temperature conditions, with additional thickness. Wall thickness is indicated in individual Piping Material Classification.
3.2 Fittings
1) Fitting construction shall generally be as follows. For CS, AS & SS
- DN50 and smaller : Socket weld - DN65 and larger : Butt weld
However, butt welding shall be used regardless of size limits as per steam turbine design guidelines for lubricating oil and control oil system.
2) All screwed connections shall have taper threads (NPT).
3) Long radius elbows shall be generally used for all piping, unless otherwise noted.
4) Dimensions shall be as follows; - Malleable iron threaded fittings: ASME B16. 3 - Socket Welded and threaded fittings: ASME B16.11 - Butt Welded fittings: ASME B16. 9 (DN1200 and under)
B
B
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
16/174
MSS-SP-75 (DN1250 to DN1500)
Non-metal fittings shall be complied with the following relevant code and manufacture standard. - GRP : AWWA C950 and AWWA M45 - HDPE: EN12201 and ISO4427 - CPVC : ASTM F441
5) To use seamless fitting instead of welded fitting is acceptable.
3.3 Flanges
1) Flange facing shall be serrated as 125~250 μ inch AARH, unless otherwise stated.
2) The bore of welding neck flanges shall correspond to the inside diameter of the connecting pipe or fitting.
3) Sizes of reducing or blind flanges are indicated by nominal pipe sizes.
4) Unless otherwise specified on material class or ISO Drawings, Flange type for AWWA C207 Class “D” shall be Ring Type.
5) Dimension shall be as follows ; - ASME class 150 to 1500 (DN 600 and under) : ASME B16. 5 - ASME class 2500 (DN 300 and under): ASME B16. 5 - ASME class 150 to 900 (DN 650 to DN 1500) : ASME B16.47 Series A - AWWA C207 Class D (DN 650 to DN 3600) : AWWA C207
6) Blank flanges shall be of the same materials as the adjoining pipe or fitting.
3.4 Gaskets
1) Dimensions shall be as follows ; - Spiral wound gasket : ASME B16.20
- Ring joint gasket and grooves : ASME B16.20
- Non-metallic gasket : ASME B16.21
2) The limiting dimensions of gaskets (other than ring joint) suitable for ASME flanges shall be in accordance with ASME B16.5, Annex C.
3) Gasket dimensions for flanges larger than DN600 shall be in accordance with the flange standard specified in the individual specification class.
4) Unless otherwise specified in material class, spiral wound gasket shall be constructed with 316SS for strip, Graphite for filler material and carbon steel outer ring.
B
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
17/174
5) In general insulating gasket will be used at the flange joints particularly called on the P&ID.
3.5 Bolts and Nuts for line flange
1) Studs: Threaded full length shall be according to ASME B1.1 class 2A unified coarse screw (UNC) for 1” and smaller diameter, and 8-UN for larger diameter.
2) Nuts: Hexagon semi-finished shall be in accordance with ASME B18. 2. 2 table 9, and thread nuts shall be in accordance with ASME B1.1 class 2B inch fit.
3) Bolt length shall be determined in accordance with ASME B16. 5 Annex "D".
4) Bolts and nuts including general grade high strength friction grip bolts shall be hot dip galvanized and subsequently centrifuged. Nuts shall be tapped up to 0.4mm oversize after galvanizing and the threads oiled to permit the nuts to be finger turned on the bolt for the full depth of the nut.
5) Bolting for non-metal pipe such as GRP, PVC, HDPE shall be furnished with carbon steel washers at both sides.
6) Unless otherwise indicated in the piping material class, bolts, nuts and washers shall be hot dip galvanized as per A153 class C.
7) Hydraulic Bolt Tensioning
Hydraulic bolt tensioning shall be used for tightening the bolts of flanged connections of equipment and piping where operating conditions require the stress distribution in the bolts to be properly controlled to obtain a reliable joint.
Bolt lengths shall be longer by the equivalent of one nut thickness to allow the use of this equipment.
Hydraulic bolt tensioning shall be applied as follows;
SERVICE ASME CLASS BOLT SIZE
All All 1 1/4” & larger
3.6 Valves
1) Valves assemblies shall be designed for the pressure and temperature rating of the class specified in the Piping Material Classes and Valve List.
2) Hydrostatic testing for valves shall be in accordance with ASME B16.34 and API 598.
3) Carbon steel having carbon contents of more than 0.25% shall not be used in Welded construction valves.
4) Unless otherwise specified, socket weld bores are according to manufacturer's standard and shall
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
18/174
conform to ASME B16.11.
5) Valve stem packing, trim and bonnet gasket material shall be manufacturer's standards, unless otherwise specified.
6) The maximum force requested at the hand wheel shall not exceed 300N (30kgf). As shown “Table-1,” the manually operated valves in the sizes and pressure classes shall be provided with a gear operator as minimum.
<Table 1>
CLASS GATE GLOBE PLUG & BALL BUTTERFLY
150
300
600
900
1500
2500 & larger
DN300 & Larger
DN250 & Larger
DN200 & Larger
DN150 & Larger
DN150 & Larger
DN100 & Larger
DN250 & Larger
DN200 & Larger
DN150 & Larger
DN100 & Larger
DN100 & Larger
DN80 & Larger
DN200 & Larger
DN150 & Larger
DN100 & Larger
DN80 & Larger
DN80 & Larger
DN80 & Larger
DN200 & Larger
DN150 & Larger
-
-
-
-
7) Gear operator type - Gate, Globe Valves : Bevel-gear type
- Ball, Plug, Butterfly Valves : Worm-gear type
8) Nonmetallic (PTFE) seated ball and non-lubricated plug valves for flammable liquid or gas services shall be of the fire-safe design.
9) Nonmetallic seated ball and plug valves shall have the ball or plug, stem and lever electro-statically grounded to the valve body.
10) All valve actuators shall have local indicators fitted to show whether the valves are in an open or shut position. Where extended spindles are used, indicators shall be fitted to both the extended spindle and to the valve spindle.
11) Plastic or bakelite valve hand-wheels are not permitted.
12) The stops limiting the travel of any valve in the "open" or "shut" position shall be arranged externally to the valve body.
13) All valves shall be closed by turning the hand-wheel in the clockwise direction when looking on top of the hand-wheel.
14) The face of each hand-wheel shall be clearly marked with the words "open" and "shut" in English, with adjacent arrows to indicate the direction of rotation to which each refers.
15) Each valve hand-wheel shall be fitted with a name-plate of an approved material, indicating in English the valve reference number and function. The name-plate shall incorporate the colour code
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
19/174
corresponding to the particular service of the piping.
16) Each valve shall be permanently marked with the code designation of valve, casing material, manufacturer’s serial number, nominal bore and the nominal pressure/test pressure and temperature (operating pressure and temperature from NP 63 onwards).
17) Hand-wheels for motorized actuators shall not rotate when the valve actuator is in use and shall be able to be operated without being mechanically connected to the actuator. Pneumatic actuators shall include solenoid valves for manual actuation with fail safe position (spring return or last position as appropriate).
18) Eye bolts shall be provided where necessary to facilitate handling heavy valves or parts of valves.
19) Spindles of valves DN65 and above, for outdoor use shall have weatherproof protection covers and valve open/close indication. In general all valves exposed to the elements shall be corrosion resistant.
20) All high pressure steam and feed valves of 125mm throat bore and over shall be provided with integral steel by-passes.
21) Butterfly valves shall only be used where specifically approved.
22) All valves material shall be as indicated in ASTM code or approved equivalent.
4. Miscellaneous Requirements
1) The SI units shall not only be applied as the measurement system for the drawings and documents but also for components.
2) As far as possible, the buried piping shall be avoided. In case of routing the underground, piping plan drawing shall be indicated for approval.
External surface of all buried carbon and stainless steel piping shall be polyethylene coated or equivalent except trench piping.
3) The tolerances for prefabricated piping assemblies shall be in accordance with the requirements of PFI ES-3
4) The tolerances and acceptance criteria for shop fabricated pipe bend shall be in accordance with the requirements of PFI ES-24.
5) Insulating flange kits to prevent galvanic corrosion between dissimilar metals shall be provided where shown on the design drawings and P & ID.
6) All pipe bends shall be minimum 3 diameter radius.
7) All butt welding fittings, flanges and valves shall be the same schedule (wall thickness) and weld end preparation, as the pipe to which they are welded unless otherwise indicated in the Piping Material Specification.
B
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
20/174
5. Abbreviation
The following acronyms and abbreviations are used in this document:
Acronym/ Abbreviation Description
A/G AS ATM AMB
Above Ground Alloy Steel Atmosphere Ambient
BB BC BE BW
Bolted Bonnet Bolted Cover Beveled End Butt weld
CA CONN CL CPVC CS
Corrosion Allowance Connection Class Chlorinate Polyvinyl Chloride Carbon Steel
DN DWG
Diameter Nominal Drawing
EFW ERW
Electric Fusion Welding Electric Resistance Welding
FB FF FLG FV
Full Bore Type Full Face (Flat Face) Flange Full Vacuum
GALV GR GRP
Galvanized Grade Glassfibre Reinforced Thermosetting Plastics
HEX. NUT HF
Hexagonal Nut Hard-faced
ID Inside Diameter
LJ LR
Lapped (Loose) Joint Long Radius
MAT'L MAX MIN M. BOLT MJ
Material Maximum Minimum Machine Bolt Mechanical Joint
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
21/174
Acronym/ Abbreviation Description
NO Number
OD OS & Y
Outside Diameter Outside Screw and Yoke
PSB PSC PE PPL PVC
Pressure Seal Bonnet Pressure Seal Cover Plain End Polypropylene Lined Polyvinyl Chloride
RF RTJ RTFE
Raised Face Ring Type Joint Face Reinforced Teflon
SB SC SCR'D SCH SDR SMLS SO SW SS STL
Screwed Bonnet Screwed Cover Screwed Schedule Standard Dimension Ratio Seamless Slip-on Weld Socket Weld Stainless Steel Stellite
THK TE TBE THRD TOE
Thickness (mm) Threaded End Threaded Both Side End Thread Threaded One Side End
UB UC U/G
Union Bonnet Union Cap/Cover Under Ground
WC WN WB
Welded Cover Welded Neck Welded Bonnet
Y TYPE Y-Type / Y-Pattern
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
22/174
6. Numbering System for Piping Class
(1) (2) (3) (4)
Example: F A 1 - S
(1) First Field : Class / Rating
Symbol Pressure Rating or Class
A : ASME Class 150
B : ASME Class 300
C : ASME Class 600
D : ASME Class 900
E : ASME Class 1500
F : ASME Class 2500
G : ASME Class Above 2500
(2) Second Field : Material
Symbol Material
A : Carbon Steel, Carbon-moly Steel
B : Low and Intermediate Alloy Steel (Cr-Mo)
C : Austenitic Stainless Steel/ Duplex
D : Copper, Brass or Bronze
E : Ductile Iron with cement lined
F : Polyvinyl Chloride (PVC), Chlorinated Polyvinyl Chloride
(CPVC), High Density Poly Ethylene (HDPE)
G : Glass fiber Reinforced Plastic(GRP)
H : Internal Lined Carbon Steel (Rubber/PTFE Lining)
(3) Third Field: Serial No.
From 1 to 9: In order of Arabic number
(4) Fourth Field: Optional
S : Boiler External Piping
First Field: Class / Rating
Fourth Field: Optional
Third Field: Serial No.
Second Field: Material
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
23/174
7. Numbering System for Valve’s Material Code
(1) (2) (3) (4) (5)
Example: VG B - A C6 - R
(1) First Field: Valve Type
Symbol Valve Type
VA : Gate valve
VB : Ball valve
VC : Check valve
VD : Diaphragm valve
VF : Butterfly valve
VG : Globe valve
VL : Angle valve
VN : Needle valve
VP : Plug valve
VS : Single block & bleed valve
VT : Stop Check Valve
VV : Double block & bleed valve
VW : 3-way
(2) Second Field: End Connection Type
Symbol End Connection Type
B : Butt welding
F : Flanged
M : Flanged x Thread(NPT)
T : Thread (Screwed)
S : Socket Welding
W : Wafer / Wafer-Lug
Z : Socket welding x Thread(NPT)
Second Field: End Connection
Fifth Field: Suffix
Fourth Field: Body Material
Third Field: Pressure Class
First Field: Valve Type
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
24/174
(3) Third Field: Pressure Class
Symbol Pressure Rating or Class
A : 150
B : 300
C : 600
D : 900
E : 1500
F : 2500
G : Above 2500
(4) Fourth Field: Body Material
Symbol Body Material
F1 : A105 Carbon Steel
F2 : A182-F1 Alloy Steel
F3 : A182-F11CL.2 Alloy Steel
F4 : A182-F22 CL.3 Alloy Steel
F5 : A182-F304L Stainless Steel
F6 : A182-F316L Stainless Steel
F7 : A182-F316 Stainless Steel
F8 : A182-F304 Stainless Steel
F9 : A182-F91 Alloy Steel
F10 : A182-F51 Duplex Steel
F11 : A182-F53 Supper Duplex Steel
C1 : A126 B Cast Iron
C2 : A216 WCB Carbon Steel
C3 : A216 WCC Carbon Steel
C4 : A217 WC1 Alloy Steel
C5 : A217 WC6 Alloy Steel
C6 : A217 WC9 Alloy Steel
C7 : A351 CF3M Stainless Steel (316L)
C8 : A351 CF8M Stainless Steel (316)
C9 : A217 C12A Alloy Steel
C10 : A351CF3 Stainless Steel (304L)
C11 : A351CF8 Stainless Steel (304)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
25/174
C12 : A995 CD3MN Duplex Steel (4A)
C13 : A995 CE3MN Super Duplex Steel (5A)
P1 : PVC (Polyvinyl Chloride)
P2 : CPVC (Chlorinated Polyvinyl Chloride)
P3 : PE (Polyethylene)
(5) Fifth Field: Suffix (Optional)
One or two symbols are used, as follows.
Symbol Description
R : Rubber Lined
S : Boiler External Piping
T : PTFE Lined (Teflon Lined)
L : Limit Switch
W : Water Seal
A base individual material code for valve may have modifications/ additions by adding a numeric character to the base code designator.
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
26/174
Attachment – 1 : Index of Piping Material Classification
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
27/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AA1 LBS LP Turbine Extraction Steam 10.0+FV 240 2.844 178.1
150 CS 1.6 mm
QJA/QHA/GCC N2 Gas 12.0 65 7.0 50
MKG/QJX H2 Gas (Steam Turbine Gas System) 12.0 65 10.0 55
MKG/QJC CO2 Gas 10.0 65 1.5 ~ 2 55
HCW Sealing / Cooling Air – Boiler 10.0 60 1.1 55
MKA/MKG Auxiliary Gas (Steam Turbine) 10.0 100 6.5 50
NAK Condensate (Steam Transformer Sys.) 15.0 150 7.3 99.6
LAS/HAH/LBG Drain and Vent 10.0 300 - -
AA2
LBS/LC*/MA* Line Condensate 10.0+FV 285 - -
150 CS 1.6 mm
PG* Closed Cooling Water 10.0 60 8.0 41
LCA CEP Suction 10.0+FV 85 0.2 37.9
GMC Oily Water (A/G) 10.0 50 4.0 35
HS* Aux. Boiler Blowdown 10.0 110 ATM 100
GMH Steam Transformer Blowdown Sump Pump 10.0 100 4.0 60
GMH Aux.Boiler Blowdown Sump Pump 10.0 100 2.0 90
GMC EP Area Drain Sump Pump 10.0 50 2.0 35
QEA Drain(Air Compressor) 12.0 65 ATM AMB
B
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
28/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AA3 EGC HFO/HCO Transfer Pump Suction 10.0 85 3.0 55
150 CS 1.6 mm
EGC HFO/HCO Transfer Pump Discharge 13.0 85 4.0 55
EGC HFO/HCO Pump Suction (From Ring Main) 10.0 85 2.0 80
EGA DFO Unloading Pump Suction / Discharge 10.0 85 4.1 50
EGC DFO Transfer Pump Suction 10.0 85 3.0 50
EGC DFO Transfer Pump Discharge 10.0 85 4.8 50
EGC DFO Forwarding Pump Suction 10.0 85 3.0 50
EG* Fuel Oil Drain / Drain Pump Discharge 13.0 150 9.6 50
MAV Lube Oil (Return & Vent for STG) 10.0 80 ATM 60
MAV Lube Oil (Dirty and Clean Oil System) 10.0 80 7.0 65
QHF Aux Boiler Fuel Oil Supply Pump Discharge 15.0 40 12.5 AMB
AA4
QE*/ HJN/
GCC/GKB Service Air 12.0 65 10.5 50
150 Internally and Externally
Galvanized Carbon Steel1.6 mm
GQA/GRS Waste Water Sewage (A/G) 10.0 50 7.0 35
AA5 SG* Fire Fighting Water (For Fresh Water) 14.5 58 13.5 48 150 Internally and Externally
Galvanized Carbon Steel1.6 mm
AA6 QKA Chilled Water 10.0 50 8.3 7 150 CS 1.6 mm
AA7 QJA Compressed Air and Nitrogen
(N2 Generator Package) 12.0 85 8.0 55 150
Internally and Externally
Galvanized Carbon Steel1.6 mm
AC1 HSK/HSJ Urea Feeding & Injection 10.0 85 4.2 65.6 150 SS 304L 0 mm
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
29/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AC1 LCM Water Separator Drain Heater To Condenser 10.0 200 5.0 177
150 SS 304L 0 mm GRS Sewage Treatment Plant (Submersible Part) 10.0 55 3.0 35
LDC Air blower discharge 10.0 85 2.0 45
AC2
GHE/GRS/GCX Service Water (Other plant user) 14.5 60 14.5 35
150 SS 316L 0 mm
QEA/QF*/ HMS/GNX,GRX/GCX/GKB
Instrument Air 12.0 65 8.9 ~ 9.5 50
GKB/GDK Potable Water (A/G) 10.0 50 6.0 35
HSG Ammonia To Boiler Unit 10.0 163 1.1 154
GMC/ GNK Boiler Wash Water Drain Sump Pump 10.0 80 4.0 60
GNN/GCC Chemical Dosing (NaOH) 10.0 50 5.0 35
PHN Chemical 10.0 60 8.0 41
QU* Sampling 10+FV 85 4.0 38
GCF BWRO High Pressure Pump, BWRO Unit 15.0 40 11 31
GCC N2 Gas Supply 10.0 50 8.0 AMB
GCF GTMDO Vacuum Pump 10.0 40 2.0 31
LDP CPP regeneration & resin transfer water LP 10.0 50 7.0 35
LDN Caustic (5% & 46%) 10.0 50 4.0 35
LDT Hot Water 10.0 85 ATM 82
GDN Chemical Dosing(Antiscalant, SBS,NaOH) 12.0 65 6.0 35
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
30/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AC3 MAV Lube Oil Feed Pipe 10.0 80 2.8 45 150 SS 304L 0 mm
LDP Resin transfer LP 10.0 50 4.0 35
AC4 GNK Boiler Wash Water for Waste Water Treatment 10.0 50 3.0 35 150 SS 316L 0 mm
AC5 GMP Condenser Area Sump Pump Discharge 10.0 40 1.5 40
150 Duplex 0 mm PAB Circulating Water Pump Discharge 10.0+FV 40 4.0 31
AC6 MAV Lubricating Oil and Control Oil (Steam Turbine) 10 80 5.8 59 150 SS304L 0 mm
AF1
GQA Sanitary Water (U/G) 4.0 50 2.0 35
150 HDPE 0 mm GMC Oily Water (U/G) 4.0 50 2.0 35
GKB Potable Water (U/G) 6.0 50 2.0 35
LDP CPP loop drain 4.0 50 2.0 35
AF2
GRN Chemical Dosing (NaOCl) 6.0 50 3.0 35
150 CPVC 0 mm
GCF CEDI Unit 8.5 40 6.5 31
GCF GTMDO Unit 6.0 40 4.0 31
GCP CIP Process 5.0 40 3.5 AMB
GDB/GDF Sea Water, Filtered sea water 7.0 45 4.5 35
GDB/GDF UF Permeate, 1st pass RO Permeate 3.5 45 1.5 35
GDB/GDF DMF / UF backwash, Sample drains, 1st & 2nd RO reject (low pressure)
7.0 45 4.0 35
GDP Desalinated water, potable water 7.0 45 4.5 35
GDP RO cleaning solution 7.0 45 4.0 35
GDN FeCl3 solution, NaOCl solution 7.0 45 4.0 35
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
31/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AG1 PAB Circulating Water Supply (U/G) 4.0+FV 40 2.4 31
150 GRP (Polyester) 0 mm
PAB Circulating Water Discharge (U/G) 4.0+FV 45 1.5 35.2
PAR FGD Seawater Supply 3.0+FV 40 1.8 31
PCB Seawater Initial Supply 3.0+FV 40 1.8 31
PA*/ PCB/PBB Other Auxiliaries Seawater Supply 10.0+FV 40 7.0 31
PAB Other Auxiliaries Seawater Discharge 10.0+FV 45 1.2 40
PAH Tube Cleaning 10.0 45 5.0 40
GDK Filtered Water 10.0 40 5.5 34
GDK Desalinated Water 10.0 40 9.0 34
GMJ Seawater Drain Sump Pump 10.0 40 2.5 34
LDP CPP Regeneration Sump Pump 10.0 50 4.0 35
GMQ Chemical Waste Water 10.0 50 4.0 35
GNK Treated Chemical Waste Water 3.0 50 2.0 35
GCF Desalinated Water Supply to Demi. Plant 7.0 40 5 31
GCF BWRO Unit Outlet 5.0 40 3 31
GCF CEDI Feed Pump 9.0 40 7.5 31
GCP BWRO Flushing Pump 7.0 40 4.5 31
GCF CEDI Unit Outlet 7.0 40 4.5 31
GDB/GDF Sea Water, Filtered sea water 7.0 45 6.0 35
GDB/GDF UF Permeate, 1st pass RO Permeate 7.0 45 1.5 35
GDB/GDF DMF / UF backwash, Sample drains, 1st & 2nd RO reject (low pressure)
7.0 45 4.0 35
GDP Desalinated water 7.0 45 4.5 35
GDP RO cleaning solution 7.0 45 4.0 35
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
32/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AG2 PAH Hypochlorite Solution (NaOCl) 10.0 45 5.8 36
150 GRP (Vinylester) 0 mm PBR Acid Solution (HCl) 10.0 50 3.5 35
PCC/PBB Electro-chlorination System Seawater Supply 10.0+FV 40 6.4 31
AG3 GMH Quenching Sump Pump Discharge 10.0 100 3.0 90 150 GRP (Epoxy) 0 mm
AG4
GCF Desalinated Water Supply to Demi. Plant 7.0 40 5 31
150 GRP (Polyester) 0 mm
GCF CEDI Feed Pump 9.0 40 7.5 31
GCF CEDI Unit Outlet 7.0 40 4.5 31
GCP CIP Process 5.0 40 3.5 AMB
GCF BWRO Unit Outlet 5.0 40 3 31
GCP BWRO Flushing Pump 7.0 40 4.5 31
AG5 SG* Fire Fighting (U/G, GIS Area) 14.5 58 13.5 48 150 GRP (Epoxy) 0 mm
AH1
PAB Circulating Water Supply (A/G) 4.0+FV 40 2.4 31
150
Duplex (up to DN50)
CS with Rubber Lined (DN65~DN3600)
0 mm
3.0 mm
Internal
lining
PAB Circulating Water Discharge (A/G) From Pump Discharge to Discharge Header
4.0+FV 45 1.5 35.2
PAB Circulating Water Pump Discharge 4.0+FV 40 2.4 31
PAR FGD Seawater Supply Pump Discharge 3.0+FV 40 1.8 31
PCB Seawater Pipeline Filling Pump Discharge 3.0+FV 40 1.8 31
PA*/PCB/ PBB Other Auxiliaries Seawater Supply Pump 10.0+FV 40 7.0 31
LDP CPP general chemical drains 10.0 50 2.0 35
HTJ Seawater Absorber Pump Discharge 3.5+FV 60 2.5 38.2
AH2 SGA Fire Fighting (For Sea Water) 14.5 50 13.5 34 150
Duplex( up to DN50)
CS with Rubber Lined
(DN65~DN400)
0 mm
3.0 mm
Internal
lining
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
33/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
AH3 GHC Make Up Water(Condensate Pump) 10.0 50 8.0 35
150
SS 316L (up to DN50)
CS with Rubber Lined
(DN65 ~ DN400)
0 mm
3.0 mm
Internal
lining
GHC Make up Water (Boiler/Deaerator filling pump) 13.0 50 11.0 35
GCF/GDP Demineralized Water 10.0 40 4.5 31
GCA Make Up Water to Demi. Plant 10.0 50 8.0 35
LDN/LDP Dilute sulphuric acid (5%) 10.0 50 4.0 35
AH5
GNN Chemical Dosing (H2SO4) for Waste Water Treatment 10.0 50 3.0 35
150 CS PTFE lined 0.0 mm Internal
lining LDN/LDP Chemical Dosing (H2SO4) for CPP 10.0 50 4.0 35
GDN Chemical Dosing (H2SO4) for Desalination 10.0 55 4.5 35
BA1
LBG Aux. Steam 20.0 300 15.0 250
300 CS 1.6 mm
LBQ IP Turbine Exhaust Steam to Deaerator 10.0+FV 399 9.4 304.3
LBS LP Turbine Extraction Steam to LP Heater #4 10.0+FV 350 5.0 229.3
LAB Feed Water Booster Pump Suction 14.0+FV 200 10.05 172.9
NAK Steam Transformer Feed Pump Discharge 24.0 150 16.0 91.3
MAL Aux. Steam HDR Drain 20.0 300 1.4 110
LAB BFW Pump Minimum Flow 16.0 200 11.5 177.9
LAB BFW Pump PSV Outlet 16.0 200 11.5 177.9
LBA HP Steam PSV & ERV Vent 20.0 390 14.0 380
LBC Cold Reheat Steam to Aux.Steam HDR (PCV Disch.) 20.0 365 15.0 320
NAK Secondary Steam 15.0+FV 205 9.0 175.4
BA2
LCA CEP Discharge 39.0+FV 85 34.8 38.3
300 CS 1.6 mm NAB Primary Condensate Pump Discharge 30.0 205 18.0 153.0
LCH HP Heater #6 Cascade Drain 26.0+FV 240 18.3 182.5
LCC CEP Discharge Heating (LP Heater No.3) 39.0+FV 150 15.5 127.8
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
34/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
BA2 LCC CEP Discharge Heating (LP Heater No.4) 39.0+FV 170 15.5 124
300 CS 1.6 mm
LCC Condensate LP Heater #4 to Deaerator 39.0+FV 200 13.0 147
LCJ LP Forward Heater Pump Discharge 39.0+FV 150 20.0 125.9
HAN Boiler Flash Tank Vent 10.0 375 1.5 360
LDK CPP Inlet & Bypass 39.0+FV 85 34.6 38.2
BA3
EGA HFO/HCO Unloading Line 15.0 85 8.0 65
300 CS 1.6 mm
EGC HFO/HCO Pump Discharge (To Each Boiler) 41.0 150 37.0 130
EGD DFO Forwarding Pump For Boiler Discharge 43.0 150 42.0 50
EGC DFO Forwarding Pump For Others Discharge 40.0 150 12.5 50
EGD HFO/HCO Recirculation Piping 40.0 150 7.0 120
BB1 MAL Leak- Off Steam 10.0+FV 540 FV 518
300 AS (P22) 1.6 mm LBB Hot Reheat PSV Vent 10.0 517 9.5 507
BB2 MAW Superheater Steam (Steam Turbine) 10.0 499 1.03 408.6
300 AS(P11) 1.6mm LBQ IP Extraction Steam (To External Desuperheater) 26.0+FV 450 19.2 404.2
BC1
GHE Service Water (From Service Water Pump To Boiler Area)
15.0 60 14.0 35
300 SS 316L 0 mm
ASME B31.3 (Chemical
Dosing Only)
/ ASME B31.1
GHE Boiler Wash Water 15.0 80 14.0 35
QCA/QCC Chemical Dosing(Steam Transformer/ Aux. Boiler) 15.0 85 10.0 AMB
QCJ Chemical Dosing (Oxygen Dosing ,to BFP suction) 25.0 60 17.0 AMB
HSJ Urea Solution(Urea Injection Skid) 20.0 85 11.5 27
HSJ Urea Solution(Urea Hydrolyzer Skid) 19.0 163 ATM 155
QUA Sampling(Aux. Boiler) 25.0 226 18.6 208
GDF 1ST SWRO Permeate 15.0 65 14.6 35
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
35/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
BC2 LDF CPP condensate outlet 41.0+FV 85 34.6 38.2
300 SS 316 0 mm LDP Resin transfer HP 41.0+FV 85 34.6 38.2
LDP/LDF Resin transfer water HP 41.0+FV 85 34.6 38.2
BC3 MKW Sealing Oil (Steam Turbine) 16.0 100 8.1 49 300 SS 316L 0 mm
CA1
LCH HP Heater #7 Cascade drain 64.0+FV 285 50.1 210.8
600 CS 1.6 mm
LBC Cold Reheat Steam 64.0+FV 399 51.6 301
MAL Cold Reheat Steam Drain 64.0+FV 399 1.4 110
HCB Shoot Blowing Steam(After CV) 40.0 396 26.0 354
LAB BFW Booster Pump Discharge 39.0 200 24.0 178
EGX Fuel Additive 65.0 150 55.0 50
CA2 SGK Gas Fire Extinguishing System 30.0 60 26.0 AMB 600 Internally and Externally
Galvanized Carbon Steel1.6 mm
CB1
MAL HRS Drain (After Drain Block Valve) 64.0 440 1.4 110
600 AS (P11) 1.6 mm MAL Aux Steam Let Down Valve Spray Water Inlet 39.0+FV 450 19.2 404.2
LBC Cold Reheat Steam (HP Exhaust Steam to NRV) 40.0+FV 64.0+FV
460 399
51.6 51.6
301 301
CB2 LCE LP By-Pass Spray Water Inlet 39.0+FV 550 23.8 45.8
600 AS (P91) 1.6 mm MAP LP By-Pass Valve Outlet 14.0+FV 550 5.0 151.8
CB3 MAL Leak-Off Steam 32.0+FV 500 5.0 450 600 AS (P22) 1.6 mm
CC1
QCA Chemical Dosing (Ammonia) 50.0 85 40 AMB
600 SS 316L 0 mm
ASME B31.3 (Chemical
Dosing Only)
/ ASME B31.1 QCJ Chemical Dosing (Oxygen Dosing, to CPP outlet) 50.0 60 32 AMB
QU* Condensate Sampling 39.0+FV 200 13 149.7
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
36/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
CC2 GDF Sea water & HP RO Brine Line 65.8 50 62.7 35 600 Super Duplex 0 mm
CC3 MAX Control Oil (Steam Turbine) 55.0 80 41.0 59 600 SS304L 0 mm
CC4 MAV/MAX Lubricating and Control Oil (Steam Turbine) 55.0 80 41.0 59 600 Tubing SS 316Ti 0 mm
DA1 LCH/LBH HP Heater #8 Cascade Drain 112.0+FV 330 89.6 266.8
900 CS 1.6 mm HAN Boiler High Pressure Drain Header 110.0 340 108 317
DB1 HAJ RH Desuperheater Out Vent 64.0 510 49.6 467.7
900 AS (P11) 1.6 mm LBA ERV Vent 40.0 420 25 410
DB1S HAJ RH Desuperheater Out Vent 64.0 510 49.6 467.7 900 AS (P11) 1.6 mm
DB2 LBB Hot Reheat Steam 64.0 550 48.3 540 900 AS (P91) 1.6 mm
DB3 MAL Steam Turbine Steam Drain 52.1+FV 547 48.9 539 900 AS (P22) 1.6 mm
DC1 QUA Hot Reheat Steam Sampling 64.0 550 48.3 540 900 SS 316 0mm
EA1 LAE/LAF BFWP Bleeding To Spray Water 140.0 200 93.0 177.4 1500 CS 1.6 mm
EB1 LBQ HP Extraction Steam to HP Heater #8 112.0+FV 420 92.3 379.9 1500 AS (P11) 1.6 mm
EB1S LAF RH Desuperheater From BFWP 92.0 510 52.6 180 1500 AS (P11) 1.6 mm BEP
(ASME SEC. I)
EB2 LAE HP By-Pass Spray Water Inlet
(After Stop Check Valve) 120.0 550 72.0 159.8 1500 AS (P91) 1.6mm
EC1
SDT High Pressure Boiler Wash Water 200.0 50 150.0 AMB
1500 SS 316 0mm MAV Steam Turbine Lifting Oil Line 177.0 80 156.9 45
QUA Sampling (HP Feedwater Heater No.6,7,8 Drain) 110+FV 330 89.0 270.1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
37/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
FA1 LAB BFW Pump Discharge (from MOV) 340.0 350 298.3 306.2
Special
2500 CS 1.6 mm
HAC Economizer Outlet Header To 1&2RY Desuperheater SH Spray Vent
331.0 376 289.3 349.5
HAG From BCP Purge Water Cooler to BCP 331.0 350 292.5 45
HAN 1&2RY Desuperheater Drain 331.0 376 ATM 100
FA1S
HAG Boiler Recirculation Pump Outlet To Economizer (NR valve to Feedwater)
331.0 376 121.4 220
Special
2500 CS 1.6 mm
BEP
(ASME SEC. I)
HAG Boiler Recirculation Pump Outlet To Economizer (BCP to NR valve)
299.0 376 162.6 220
HAC Eco. Outlet Header to 1&2RY Desuperheater Spray Water
331.0 376 289.3 349.5
LAB BFW Pump Discharge (After Check Valve) 331.0 350 296.2 306.1
FB1
HAH 2RY SH Inlet Vent 292.0 454 262.4 430.7
Special
2500 AS (P22) 1.6 mm
HAN 2RY Pass Inlet Manifold Drain 311.0 450 108.0 317.0
HAH W/S Equalizing Line Vent 297.0 457 266.7 423.0
MAL HP Steam Drain 283.0 440 1.4 110
HAC 1RY SH Spray Water 292.0 465 263.9 349.5
HAN Roof Outlet Header Drain (After Block Valve) 311.0 395 ATM 100.0
FB1S
HAC PRI. Desuperheater Spray Water 292.0 465 264.2 349.5
Special
2500 AS (P22) 1.6 mm
BEP
(ASME SEC. I)
HAH 2RY SH Inlet Vent 292.0 465 262.2 430.7
HAD 2RY Pass Inlet Manifold 311.0 450 271.7 423
HAH W/S Equalizing Line Vent 297.0 457 266.7 423
FC1 MAV Lubricating Oil (Steam Turbine) 350.0 80.0 238.4 59.0 2500 SS 321 0mm
GA1 LAB BFW Pump Discharge (to MOV) 455.0 200 305.0 177.9
3000 CS 1.6 mm Intermediate Class LAB BFW Pump Discharge (Min. Flow) 455.0 200 305.0 177.9
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
38/174
Index of Piping Material Classification FV: Full Vacuum
Class KKS Code Service
Design Condition Operating ConditionClass
Rating
Basic
Material
Additional
Thickness Remark
Pressure
(barg)
Temp.
(oC)
Pressure
(bara)
Temp.
(oC)
GB1 LBA HP Steam 283.0 550 257.3 540
3500 AS (P91) 1.6 mm Intermediate Class LBA HP Steam Vent 283.0 550 258.0 543.5
HAN 3RY SH Outlet Drain 283.0 550 2.0 443
HCB Shoot Blowing Steam (Before CV) 288.0 525 260.1 498.3
GB1S
LBA From 3Y SH Header To HP Turbine 283.0 550 257.3 540
3500 AS (P91) 1.6 mm
BEP
(ASME SEC. I)
Intermediate Class
HAH 3RY SH Outlet Drain 283.0 550 257.3 540
HAH Desuperheater Vent 288.0 505 259.5 481
HAC/HAG Desuperheater Spray Water 288.0 525 260.1 349.5
HCB Shoot Blowing Steam (Before CV) 288.0 525 260.1 498.3
GC1
QUA BFW Sampling 340.0 350 298.8 306.1
4500 SS 316 0 mm QUA HP Steam Sampling 283.0 550 257.3 540.0
QUH BCP Suction Sampling 298.0 382 274.0 373.0
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
39/174
Attachment – 2 : Piping Material Class Sheets
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
40/174
PIPING MATERIAL CLASS
AA1
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
LP Turbine Extraction Steam 10+FV 240 CO2 Gas 10.0 65
N2 Gas 12.0 65 Sealing / Cooling Air – Boiler 10.0 60
H2 Gas 12.0 65 Drain and Vent 10.0 300
Auxiliary Gas (Steam Turbine) 10.0 100 Condensate(Steam Transformer Sys) 15.0 150
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. For pipe DN850 and above, the stiffness ring is requested. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/16.47 - Group 1.1 Class 150)
Temp (℃) 50 100 150 200 250 300 325
Press (Barg) 19.2 17.7 15.8 13.8 12.1 10.2 9.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
650 ~ 900 S/STD 9.53 ASTM A672 B60 CL.12 EFW, BE 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 600 ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
650 ~ 900 ASTM A234 WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
41/174
PIPING MATERIAL CLASS
AA1
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL.150
ASTM A105
SW RF ASME B16.5
65 ~ 600 CL 150 WN RF ASME B16.5
650 ~ 900 CL 150 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 600 CL 150 316 SS Strip with Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF ASME B16.20
650 ~ 900 CL 150 316 SS Strip with Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1
80 ~ 900 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-AC2 4
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 3
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-AC2 4
Check
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-AC2
650~900 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Dual Plate, Flanged Type, B16.47 Ser-A, RF
VCF-AC2-1
Ball
25 ~ 50 CL 600 ASTM A105 Body, SS304 Trim, RTFE Seat, Full Port, Side Entry, Floating Ball, with 75mm S/80 Nipple, SW
VBS-CF1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, RF
VBF-AC2
Butterfly 80 ~ 600 CL 150 ASTM A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.5,RF
VFF-AC2
Note :
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
4. The suffix ‘-W’ shall be added to valve material code when water seal is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
42/174
PIPING MATERIAL CLASS
AA2
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Line Condensate 10.0+FV 285 Aux. Boiler Blowdown 10.0 110
Closed Cooling Water 10.0 60 Steam Transformer Blowdown Sump Pump 10.0 100
CEP Suction 10.0+FV 85 Aux. Boiler Blowdown Sump Pump 10.0 100
Oily water (A/G) 10.0 50 EP Area Drain Sump Pump 10.0 50
Drain (Air Compressor) 12.0 65
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. For pipe DN850 and above, the stiffness ring is requested. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/B16.47 -Group 1.1 Class 150)
Temp (℃) 50 100 150 200 250 300 325
Press (Barg) 19.2 17.7 15.8 13.8 12.1 10.2 9.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
650 ~ 900 S/STD 9.53 ASTM A134 A285C EFW, BE
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 600 - ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
650 ~ 900 - ASTM A234 WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
43/174
PIPING MATERIAL CLASS
AA2
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~50 CL 150
ASTM A105
SW RF ASME B16.5
65 ~ 600 CL 150 WN RF ASME B16.5
650 ~ 900 CL 150 WN RF ASME B16.47
Ser. A
Gasket
25 ~ 600 CL 150 316 SS Strip with Graphite
filler
Spiral Wound, CS Outer Ring 4.5mmT,
RF, ASME B16.20
650 ~ 900 CL 150 316 SS Strip with Graphite
filler
Spiral Wound, CS Inner/Outer Ring
4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW VAS-CF1
80 ~ 850 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-AC2
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-AC2 3,6,7
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type disc, SWxNPT
VGZ-CF1 4
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug Type Disc, SW VGS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-AC2
Check
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-AC2
650~850 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Dual Plate, Flanged Type, B16.47 Ser-A, RF
VCF-AC2-1
Butterfly
80 ~ 600 CL 150 ASTM A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.5,RF
VFF-AC2 5
650 ~ 850 CL 150 ASTM A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.47 Ser. A, RF
VFF-AC2-1 5
Needle 80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Needle Disc, BW VNB-AC2
Ball 25 ~ 50 CL 600
ASTM A105 Body, SS304 Trim, RTFE Seat, Full Port, Side Entry, Floating Ball with 75mm S/80 Nipple, SW
VBS-CF1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, RF
VBF-AC2
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The flanged valve shall be utilized when mating with equipment flanged nozzle or flanged end special items.
4. The end type valve (SWxNPT) shall be used for instrument root valve.
5. The butterfly valve (EPDM seat) can be used up to design temperature 80℃.
6. The suffix ‘-L’ shall be added to valve material code when limit switch is applied.
7. The suffix ‘-W’ shall be added to valve material code when water seal is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
44/174
PIPING MATERIAL CLASS
AA3
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HFO/HCO Transfer Pump Suction/Discharge 10.0 / 13.0 85 DFO Forwarding Pump Suction 10.0 85
HFO/HCO Pump Suction (From Ring Main) 10.0 85 Fuel Oil Drain/ Drain Pump Discharge 13.0 150
DFO Unloading Pump Suction/ Discharge 10.0 85 Lube Oil (Return & Vent for STG) 10.0 80
DFO Transfer Pump Suction/ Discharge 10.0 85 Lube Oil (Dirty and Clean Oil System) 10.0 80
Aux Boiler Fuel Oil Supply Pump Discharge 15.0 40
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 150)
Temp (℃) 50 100 150 200 250 300 325
Press (Barg) 19.2 17.7 15.8 13.8 12.1 10.2 9.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
650 ~ 850 S/STD 9.53 API 5L Gr.B EFW, BE
1
1200 S/XS 12.70 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65~ 600 - ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
650 ~ 1200 - ASTM A234 WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
45/174
PIPING MATERIAL CLASS
AA3
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 150
ASTM A105
SW RF ASME B16.5
65 ~ 600 CL 150 WN RF ASME B16.5
650 ~ 850 CL 150 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 600 CL 150 316 SS Strip with
Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
650 ~ 850 CL 150 316 SS Strip with
Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW VAS-CF1
80 ~ 800 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-AC2
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 3
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW VGS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-AC2
Check
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-AC2
650~800 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Dual Plate, Flanged Type, B16.47 Ser-A, RF
VCF-AC2-1
Ball
25 ~ 50 CL 600 ASTM A105 Body, SS304 Trim, RTFE Seat, Floating Ball, Full Port, Top Entry, with 75mm S/80 Nipple, SW
VBS-CF1-1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS304 Trim, BB, RTFE Seat, Top entry, Floating Ball, Full port, BW
VBB-AC2
200 ~ 800 CL 150 ASTM A216 WCB Body, A105+ENP or SS304 Trim, BB, RTFE Seat, Top entry, Trunnion Ball, Full port, BW
VBB-AC2-1
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
46/174
PIPING MATERIAL CLASS
AA4
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Service Air 12.0 65 Waste Water Sewage (A/G) 10.0 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 150)
Temp (℃) 50 100 150 200
Press (Barg) 19.2 17.7 15.8 13.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106Gr.B GALV
SMLS, TE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
1,3
80 S/STD 5.49 1,3
100 S/STD 6.02 1,3
150 S/STD 7.11 1,3
200 S/STD 8.18 1,3
250 S/STD 9.27 1,3
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 GALV Forged End, TE ASME B16.11
65 ~ 250 ASTM A234 WPB GALV
SMLS, BW ASME B16.9 Schedule Match Pipe
1,2,3
Thredolet 25 ~ 50 CL.3000 ASTM A105 GALV Forged End, TE MSS SP- 97
Weldolet 65 ~ - ASTM A105 GALV Forged End, BW MSS SP- 97 1,2
Boss 25~ 50 CL.3000 ASTM A105 GALV Forged End, TE -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 150
ASTM A105 GALV TE FF,
ASME B16.5
65 ~ 250 CL 150 SO FF
Gasket 25 ~ 250 CL 150 Compressed Non-
Asbestos 1.6mmT Full Face ASME B16.21
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
47/174
PIPING MATERIAL CLASS
AA4
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, TE
VAT-CF1
80 ~ 250 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC2
Globe 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug Type Disc, TE
VGT-CF1
80 ~ 250 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC2
Check 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, TE VCT-CF1
80 ~ 250 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, FF VCF-AC2
Ball
25 ~ 50 CL 600 ASTM A105 Body, SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, TE
VBT-CF1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-AC2-1
Butterfly 80 ~ 250 CL 150 ASTM A216-WCB Body, SS304 Trim Design API 609 Cat A, EPDM Seat, ASME B16.5, wafer lug type
VFW-AC2
Note:
1. DN65 & larger piping shall be galvanized internally and externally after spool pre-fabrication and the galvanized piping shall be complied with the requirement of BS EN ISO 1461 or equivalent.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. All galvanized connections shall be threaded or flanged for field joint.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
48/174
PIPING MATERIAL CLASS
AA5
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1/ NFPA
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Fire Fighting Water (For Fresh Water) 14.5 58
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group Class 150)
Temp (℃) 50 100 150 200 250 300 325
Press (Barg) 19.2 17.7 15.8 13.8 12.1 10.2 9.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/80 3.73
ASTM A106 Gr.B GALV
SMLS, TE
ASME B36.10
25 S/80 4.55
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE or PE
4
80 S/STD 5.49 4
100 S/STD 6.02 4
150 S/STD 7.11 4
200 S/STD 8.18 4
250 S/STD 9.27 4
300 ~ 600 S/STD 9.53 4
650 ~ 700 S/STD 9.53 ASTM A134 A285C GALV EFW, BE or PE 4
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A105 GALV. Forged End, TE ASME B16.11
65 ~ 600 - ASTM A234 WPB GALV SMLS, BW or Grooved ASME B16.9 Schedule Match Pipe
2,4
650 ~ 700 - ASTM A234 WPB GALV Welded, BW or Grooved ASME B16.9 Schedule Match Pipe
1,2,4
Threadolet 15 ~ 50 CL.3000 ASTM A105 GALV Forged End, TE MSS SP- 97
Weldolet 65 ~ - ASTM A105 GALV Forged End, BW MSS SP- 97
Boss 15~ 50 CL.3000 ASTM A105 GALV Forged End, TE -
Grooved Coupling/Fittings
65 ~700 Ductile Iron Grooved 9,10
Plate A516 Gr.60
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
49/174
PIPING MATERIAL CLASS
AA5
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1/ NFPA
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
15 ~ 50 CL 150
ASTM A105 GALV
TE FF ASME B16.5
65 ~ 600 CL 150 SO FF
650 ~ 700 CL 150 WN FF ASME B16.47 Ser. A
Gasket All CL 150 EPDM 3.2 mmT, Full Face ASME B16.21
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, TE
VAT-CF1
80 ~ 700 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC2
Globe 15 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug type Disc, TE
VGT-CF1
80 ~ 700 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC2
Check 15 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, TE VCT-CF1
80 ~ 700 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, FF VCF-AC2
Ball
15 ~ 50 CL 600 ASTM A105 Body, SS 304 Trim, Lever Operated, RTFE Seat, Side Entry, Floating Ball, TE
VBT-CF1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-AC2-1
200 ~ 600 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Trunnion Ball, FF
VBF-AC2-2
Butterfly
80 ~ 600 CL 150 A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.5,FF
VFF-AC2-2
650 ~ 850 CL 150 A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.47 Ser. A, FF
VFF-AC2-3
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. All equipment, valves and etc shall be UL listed or FM approved or equivalent.
4. DN65 & larger piping shall be galvanized internally and externally after spool pre-fabrication and the galvanized piping shall be complied with the requirement of BS EN ISO 1461 or equivalent.
5. The screwed joint will be connected as seal-weld to prevent from service leakage, if required.
6. Piping material for foam concentrate shall be applied to the Vendor’s recommendation.
7. Final color of all pipes and fittings shall be red color (RAL 3000).
8. Flanges shall be supplied with raised face in lieu of flat face when mating with equipment flanges having a raised face.
9. The material of grooved fitting & coupling shall be ductile iron based on UL listed or FM approved.
10. In the event that some bare metal is exposed during fabricating and manufacturing, the affected areas may be scrubbed with a stiff wire brush to remove loose zinc flakes and chips. These bare areas may then be coated with a zinc-rich galvanizing paint/spray after the grooving operation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
50/174
PIPING MATERIAL CLASS
AA6
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Chilled Water 10.0 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 150)
Temp (℃) 50 100 150
Press (Barg) 19.2 17.7 15.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 600 ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 150 ASTM A105 SW RF ASME B16.5
65 ~ 600 CL 150 ASTM A105 WN RF ASME B16.5
Gasket 25 ~ 600 CL 150 316 SS Strip with
Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
51/174
PIPING MATERIAL CLASS
AA6
Rating ASME Class 150
Material Carbon Steel
Code ASME B31.1
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-AC2
Globe
25 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 2
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type disc, BW
VGB-AC2
Check 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-AC2
Butterfly 80 ~ 600 CL 150 ASTM A216 WCB Body, Eccentric Design, EPDM Seat, ASME B16.5, RF
VFF-AC2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The end type valve (SWxNPT) shall be used for instrument root valve.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
52/174
PIPING MATERIAL CLASS
AA7
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Compressed Air (N2 Generator Package) 12.0 85 Nitrogen Gas(N2 Generator Package) 12.0 85
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/16.47 - Group 1.1 Class 150)
Temp (℃) 50 100 150
Press (Barg) 19.2 17.7 15.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B GALV
SMLS, TE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, PE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 600 ASTM A536, Gr. 65-45-12
SMLS, Groove ends -
Plate A515 Gr.60 A516 Gr.70
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 600 CL 150 ASTM A105 LJ RF ASME B16.5
Gasket 25 ~ 600 CL 150 Nitrile-bound fiber Fiber gasket, 1.5mm, Garlock
2900 or equivalent ASME B16.20
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
53/174
PIPING MATERIAL CLASS
AA7
Rating ASME Class 150
Material Carbon Steel (GALV)
Code ASME B31.1
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, TE
VAT-CF1
80 ~ 850 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-AC2
Globe 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Plug Type Disc, TE
VGT-CF1
80 ~ 250 CL 150 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, RF
VGF-AC2
Check 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, TE VCT-CF1
80 ~ 250 CL 150 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, RF
VCF-AC2
Ball
25 ~ 50 CL 600 ASTM A105 Body, SS 304 Trim, RTFE Seat, Side Entry,
Floating Ball, TE VBT-CF1
80 ~ 150 CL 150 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE
Seat, Side Entry, Floating Ball, RF VBF-AC2
Note :
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
54/174
PIPING MATERIAL CLASS
AC1
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Urea Feeding & Injection 10.0 85 Water Separator Drain Heater To Condenser 10.0 200
Air blower discharge 10.0 85 Sewage Treatment Plant (Submersible Part) 10.0 55
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100 150 200
Press (Barg) 15.3 13.3 12.0 11.2
Note. The pressure and temperature limits for casting valve (Group 2.1 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP304L
SMLS, PE
ASME B36.19
20 S/40S 2.87
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
SMLS, BE
80 S/40S 5.49
100 S/40S 6.02
150 S40S 7.11
200 S/40S 8.18
250 S/10S 4.19
Welded, BE
300 S/10S 4.57
350 S/10S 4.78
500 S/10S 5.54
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F304L Forged End, SW ASME B16.11
65 ~ 200 ASTM A403 WP304L SMLS, BW ASME B16.9 Schedule Match Pipe
1
250 ~ 500 ASTM A403 WP304L Welded, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 15 ~ 50 CL.3000 ASTM A182 F304L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F304L Forged End, BW MSS SP- 97
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
55/174
PIPING MATERIAL CLASS
AC1
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Boss 15~ 50 CL.3000 ASTM A182 F304L Forged End, SW -
Plate A240 Gr.304L
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 150 ASTM A182 F304L SW RF ASME B16.5
65 ~ 500 CL 150 ASTM A182 F304L WN RF ASME B16.5
Gasket All CL 150
316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF ASME B16.20/ B16.21
Klingersil C4430 3mm T Synthetic fiber / NBR 3
Bolt / Nut All A193 B8 CL. 2 / A194-8
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600
ASTM A182 F304L Body, SS 304L Trim , BB, OS&Y, Solid Wedge Disc, SW
VAS-CF5
80 ~ 500 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-AC10
Globe
25 CL 600 ASTM A182 F304L Body, SS 304L Trim, BB, OS&Y, Plug Type Disc SWxNTP
VGZ-CF5 2
15 ~ 50 CL 600 ASTM A182 F304L Body, SS 304L Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF5
80 ~ 500 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BB, OS&Y, Cone Type Disc, RF
VGF-AC10
Check
15 ~ 50 CL 600 ASTM A182 F304L Body, SS 304L Trim, BC, Lift Type, SW VCS-CF5
25~ 200 CL 150 ASTM A182 316L Body, 316L trim, PTFE trim, BC, Spring wafer or Twin Plate NRV Type, RF
VCF-AF6 3
80 ~ 500 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BC, Swing Type, RF VCF-AC10
Ball
15 ~ 50 CL 600 ASTM A182 F304L Body, SS 304L Trim, RTFE Seat, Side Entry, Floating Ball, with 75mm S/40S Nipples, SW
VBS-CF5
80 ~ 150 CL 150 ASTM A351 CF3 Body, SS 304L Trim, RTFE Seat, Side Entry, Floating Ball, RF
VBF-AC10
Butterfly 80 ~ 600 CL 150 ASTM A351 CF3 Body, Eccentric Design, EPDM or PTFE Seat, ASME B16.5, RF
VFF-AC10 4,5
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe. 2. The end type valve (SWxNPT) shall be used for instrument root valve. 3. The gasket and valve type can be used for condensate polishing plant (vendor package) such as air blower discharge.
4. The butterfly valve (EPDM seat) can be used up to design temperature 80℃.
5. PTFE seat for butterfly valve shall be used for sewage treatment system.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
56/174
PIPING MATERIAL CLASS
AC2
Rating ASME Class 150
Material Stainless Steel (316L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Service Water (Other Plant User) 14.5 60 Potable Water (A/G) 10.0 50
Instrument Air 12.0 65 Ammonia To Boiler Unit 10.0 163
Chemical Dosing (NaOH) 10.0 50 Chemical Dosing(NaOH) 10.0 50
BWRO High Pressure Pump 15.0 40 BWRO Unit 15.0 40
N2 Gas Supply 10.0 50 GTMDO Vacuum Pump 10.0 40
CPP regeneration & resin transfer water LP 10.0 50 Caustic (5% & 46%) 10.0 50
Chemical Dosing(Antiscalant, SBS, NaOH) 12.0 65 Boiler Wash Water Drain Sump Pump 10.0 80
Chemical 10.0 60 Hot Water 10.0 85
Sampling 10+FV 85
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100 150 200 250
Press (Barg) 15.3 13.3 12.0 11.2 10.5
Note. The pressure and temperature limits for casting valve (Group 2.2 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316L
SMLS, PE
ASME B36.19
4
20 S/40S 2.87 4
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
SMLS, BE
80 S/40S 5.49
100 S/40S 6.02
150 S40S 7.11
200 S/40S 8.18
250 S/10S 4.19
Welded, BE
300 S/10S 4.57
350 ~ 450 S/10S 4.78
500 ~ 550 S/10S 5.54
600 S/10S 6.35
700 - 9.53
Fittings
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
57/174
PIPING MATERIAL CLASS
AC2
Rating ASME Class 150
Material Stainless Steel (316L)
Code ASME B31.1
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW ASME B16.11 4
65 ~ 200 - ASTM A403 WP316L SMLS, BW ASME B16.9 Schedule Match Pipe
1
250 ~ 700 - ASTM A403 WP316L Welded, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F316L Forged End, BW MSS SP- 97
Boss 15~ 50 CL.3000 ASTM A182 F316L Forged End, SW -
Plate A240 Gr.316L
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
15 ~ 50 CL 150
ASTM A182 F316L
SW RF ASME B16.5
2,4
65 ~ 600 CL 150 WN RF 2
700 CL 150 WN RF ASME B16.47 Ser.A 2
Gasket
15 ~ 600 CL 150
316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20/
B16.21
Klingersil C4430 3mm T Synthetic fiber / NBR 5
700 CL 150 316 SS Strip with
Graphite filler
Spiral Wound, SS Inner/ Outer
Ring 4.5mmT, RF, ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF6 4
80 ~ 600 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-AC7
Globe
15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF6 4
25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF6 3
80 ~ 600 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Cone Type Disc, RF
VGF-AC7
Check
15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, SW VCS-CF6 4
25~ 200 CL 150 ASTM A182 F316L Body, PTFE trim, BC, Spring wafer or Twin Plate NRV Type, RF
VCF-AF6 5
80 ~ 600 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BC, Swing Type, RF
VCF-AC7
Ball
15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, with 75mm S/40S Nipples, SW
VBS-CF6 4
10 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, Thread
VBT-CF6
15 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, with 75mm S/40S Nipples, SWxNPT
VBZ-CF6 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
58/174
PIPING MATERIAL CLASS
AC2
Rating ASME Class 150
Material Stainless Steel (316L)
Code ASME B31.1
25 ~ 80 CL 150 ASTM A351 CF3M Body, SS 316L Trim, PTFE Seat, Side Entry, Floating Ball, RF
VBF-AC7 2,5
Butterfly
80 ~ 600 CL 150 ASTM A351-CF3M Body, Eccentric Design, EPDM Seat, ASME B16.5, RF
VFF-AC7 6
700 CL 150 ASTM A351-CF3M Body, Eccentric Design, EPDM Seat, ASME B16.47 Ser.A, RF
VFF-AC7-2 2,6
Stop Check 25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Y-Type, SW
VTS-CF6
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Flanges and flanged valve shall be supplied with flat face in lieu of raised face when mating with GRP piping, firefighting line or equipment flanged nozzle.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
4. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines and N2 gas line for GTMDO unit.
5. The gasket and valve type can be used for condensate polishing plant (vendor package) such as regeneration & resin transfer water LP and Caustic (5% & 46%) service.
6. The butterfly valve (EPDM seat) can be used up to design temperature 80℃.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
59/174
D
PIPING MATERIAL CLASS
AC3
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Lube Oil Feed Pipe 10.0 80 Resin transfer LP 10.0 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100
Press (Barg) 15.3 13.3
Note. The pressure and temperature limits for casting valve (Group 2.1 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP304L
SMLS, PE
ASME B36.19
20 S/40S 2.87
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
80 S/40S 5.49
SMLS, BE
100 S/40S 6.02
150 S/40S 7.11
200 S/40S 8.18
250 S/40S 9.27 Welded, BE
300 S/40S 9.53
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F304L Forged End, SW ASME B16.11
65 ~ 200 - ASTM A403 WP304L SMLS, BW ASME B16.9 Schedule Match Pipe
1
250 ~ 300 - ASTM A403 WP304L Welded, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 15 ~ 50 CL.3000 ASTM A182 F304L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F304L Forged End, BW MSS SP- 97
Boss 15~ 50 CL.3000 ASTM A182 F304L Forged End, SW -
Plate A240 Gr.304L
Flange, Gasket & Bolt / Nut
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
60/174
PIPING MATERIAL CLASS
AC3
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Item Size (DN) Rating Material Description Dimension Note
Flange 15~50 CL 150 ASTM A182 F304L SW RF ASME B16.5
65 ~ 300 CL 150 ASTM A182 F304L WN RF ASME B16.5 2
Gasket All CL 150
316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20/
B16.21
Klingersil C4430 3mm T Synthetic fiber / NBR 3
Bolt / Nut All A193 B8 CL.2 /A194 8
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600
ASTM A182 F304L Body, SS 304L Trim , BB, OS&Y, Solid Wedge Disc, SW
VAS-CF5
80 ~ 300 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-AC10
Globe
15 ~ 50 CL 600 ASTM A182 F304L Body, SS 304L Trim, BB, OS&Y, Plug Type Disc SW
VGS-CF5
25 CL 600 ASTM A182 F304L Body, SS 304L Trim, BB, OS&Y, Plug Type Disc, NPT
VGT-CF5
80 ~ 300 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BB, OS&Y, Cone Type Disc, RF
VGF-AC10
Check 80 ~ 300 CL 150 ASTM A351 CF3 Body, SS 304L Trim, BC, Swing Type, RF VCF-AC10
Ball
50 ~ 150 CL 150 ASTM A351 CF3 Body, SS 304L Trim, RTFE Seat, Side
Entry, Floating Ball, , RF VBF-AC10
50 ~ 150 CL 150 ASTM A351 CF3M Body, SS 316L Trim, RTFE Seat, Side
Entry, Floating Ball, RF VBF-AC7 3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Special considerations for resin transfer duty:
Elbows to be 1.5D radius
Tees to have 1.5D radius branch set
No internal protrusions
Minimize direction changes
Gaskets to be flush within bore of pipe
3. The gasket and valve type can be used for condensate polishing plant (vendor package) such as Resin transfer LP line.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
61/174
PIPING MATERIAL CLASS
AC4
Rating ASME Class 150
Material Stainless Steel (316L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Boiler Wash Water for Waste Water Treatment 10.0 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100 150 200 250
Press (Barg) 15.3 13.3 12.0 11.2 10.5
Note. The pressure and temperature limits for casting valve (Group 2.2 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316L
SMLS, PE
ASME B36.19
3
20 S/40S 2.87 3
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/10S 3.05
SMLS, BE
80 S/10S 3.05
100 S/10S 3.05
150 S/10S 3.40
200 S/10S 3.76
250 S/10S 4.19
Welded, BE
300 S/10S 4.57
350 ~ 450 S/10S 4.78
500 ~ 550 S/10S 5.54
600 S/10S 6.35
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW ASME B16.11 3
65 ~ 200 ASTM A403 WP316L SMLS, BW ASME B16.9 Schedule Match Pipe
1
250 ~ 600 ASTM A403 WP316L Welded, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F316L Forged End, BW MSS SP- 97
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
62/174
PIPING MATERIAL CLASS
AC4
Rating ASME Class 150
Material Stainless Steel (316L)
Code ASME B31.1
Boss 25~ 50 CL.3000 ASTM A182 F316L Forged End, SW -
Plate A240 Gr.316L
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 150
ASTM A182 F316L SW RF
ASME B16.5 2,3
65 ~ 600 CL 150 WN RF 2
Gasket All CL 150 316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Check 15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, SW VCS-CF6
80 ~ 600 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BC, Swing Type, RF
VCF-AC7
Ball 15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, with 75mm S/40S Nipples, SW
VBS-CF6
Globe 25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF6
Butterfly 80 ~ 600 CL 150 ASTM A351 CF3M Body, Eccentric Design, EPDM Seat, ASME B16.5, RF
VFF-AC7
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Flanges shall be supplied with flat face in lieu of raised face when mating with GRP piping.
3. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
63/174
PIPING MATERIAL CLASS
AC5
Rating ASME Class 150
Material Duplex
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Condenser Area Sump Pump Discharge 10.0 40 Circulating Water Pump Discharge 10.0+FV 40
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.8 Class 150)
Temp (℃) 50 100
Press (Barg) 19.5 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A790 S31803
SMLS, PE
ASME B36.19 /
ASTM A790
40 S/40S 3.68
50 S/40S 3.91
65 S/10S 3.05
SMLS, BE
80 S/10S 3.05
100 S/10S 3.05
150 S/10S 3.40
200 S/10S 3.76
250 S/10S 4.19
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F51 Forged End, SW ASME B16.9 Schedule Match Pipe
1
65 ~ 250 ASTM A815 WPS31803 SMLS, BW 1
Sockolet 25 ~ 50 CL.3000 ASTM A182 F51 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F51 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F51 Forged End, SW -
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 150 ASTM A182 F51 SO FF
ASME B16.5
25 ~ 50 CL 600 ASTM A182 F51 SO FF 2
65 ~ 250 CL 150 ASTM A182 F51 WN FF
Gasket All EPDM 3.2mmT, Full Face ASME B16.21
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
64/174
PIPING MATERIAL CLASS
AC5
Rating ASME Class 150
Material Duplex
Code ASME B31.1
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS&Y, Solid Wedge Disc, FF
VAF-CF10
80 ~ 250 CL 150 ASTM A995 CD3MN Body, SS S31803 Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC12
Globe 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS & Y, Plug Type Disc, FF
VGF-CF10
80 ~ 250 CL 150 ASTM A995 CD3MN Body, S31803 Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC12
Check 25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BC, Lift Type, FF VCF-CF10
80 ~ 250 CL 150 ASTM A995 CD3MN Body, S31803 Trim, Swing Type, FF VCF-AC12
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The 600# flange can be used for valve connection.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
65/174
PIPING MATERIAL CLASS
AC6
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Lubricating Oil and Control Oil (Steam Turbine) 10 80
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100
Press (Barg) 15.3 13.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A312 TP304L
SMLS, BE
ASME B36.19
40 S/40S 3.68
50 S/40S 3.91
80 S/10S 3.05
100 S/10S 3.05
150 S/10S 3.40
200 S/10S 3.76
250 S/10S 4.19 Welded, BE
300 S/10S 4.57
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25~ 200 - ASTM A403 WP304L SMLS, BW ASME B16.9 Schedule Match Pipe
1,2
250 ~ 300 - ASTM A403 WP304L Welded, BW ASME B16.9 Schedule Match Pipe
1
Plug / Threadolet ~50 CL.3000 ASTM A182 F304L Forged End, TE ASME B16.11 / MSS SP- 97
3
Weldolet - ASTM A182 F304L Forged End, BW MSS SP- 97
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange ~ 300 CL 150 ASTM A182 F304L WN RF ASME B16.5
Gasket All CL 150 316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20
Bolt / Nut All A193 B8 CL.2 /A194 8
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
66/174
PIPING MATERIAL CLASS
AC6
Rating ASME Class 150
Material Stainless Steel (304L)
Code ASME B31.1
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. For size up to DN50, 5D bend instead of elbow can be used if the piping route is allowed. The bend thinning allowance for 5 pipe diameters is reflected into pipe wall thickness.
3. Thread connections allows the downstream of vents, drains, hydrostatic test connections, instrument take off and to match equipment.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
67/174
PIPING MATERIAL CLASS
AF1
Rating ASME Class 150
Material HDPE (High Density Polyethylene)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Sanitary Water (U/G) 4.0 50 Potable Water (U/G) 6.0 50
Oily Water (U/G) 4.0 50 CPP loop drain 4.0 50
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for PVC Valve
Temp. (℃) 38 43 50
Press (Barg) 10.3 7.6 7.1
The specific pressure-temperature rating for valve shall be followed as per Manufacturer’s Pressure/Temperature limitation. The limitation shall be covered for the shown service’s design condition.
Pipe
Item Size (OD) SCH. THK (mm)
Material Description Dimension Note
Pipe
OD40 SDR11 3.7
HDPE PE3408
(PE 100) Fusion Bonded EN 12201/ ISO 4427
2
OD63 SDR11 5.8 2
OD90 SDR11 8.2 2
OD110 SDR11 10.0 2
OD125 SDR11 11.4 2
Fittings
Item Size (OD) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
40-125 SDR11 HDPE PE3408
(PE 100) Fusion Bonded EN 12201/ ISO 4427 2
Flange, Gasket & Bolt / Nut
Item Size
(DN/OD) Rating Material Description Dimension Note
Flange All CL 150 HDPE PE3408
with Metal Ring Lap Joint FF (Metal Ring Flange : A182F304)
ASME B16.5
Gasket All CL 150 EPDM 3.2 mmT, Full Face ASME B16.21
Bolt / Nut All A193 B8M CL 2 / A194 8M
Stud Bolt /Heavy Hex Nuts with 2-SS Washers
ASME B1.1 /ASME B18.2.2
Valves
Item Size
(DN/OD) Rating Description Material Code Note
Gate All CL 150 PVC, Flanged, FF VAF-AP1
Check All CL 150 PVC, FF, Swing Type VCF-AP1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
68/174
PIPING MATERIAL CLASS
AF1
Rating ASME Class 150
Material HDPE (High Density Polyethylene)
Code ASME B31.1
Note:
1. The type and series for high density polyethylene pipe (HDPE) for underground pipework shall be in accordance with EN 12201 (ASTM D1248 and ASTM 3350, PE 3408) or equivalent.
2. The outside diameter dimensions of HDPE piping components shall be per EN 13244 / ISO 4427.
3. Joints in high density polyethylene pipe shall be of the fusion type, either butt or socket depending on pipe size and the recommendations of the pipe manufacturer.
4. HDPE pipe shall be handled, stored as per manufacturer recommendation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
69/174
PIPING MATERIAL CLASS
AF2
Rating ASME Class 150
Material CPVC
Code ASME B31.1
Service D.P.
(Barg)D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Chemical Dosing (NaOCl) 6.0 50 CEDI Unit 8.5 40
GTMDO Unit 6.0 40 CIP Process 5.0 40
Sea Water, Filtered sea water 7.0 45 UF Permeate, 1st pass RO Permeate 3.5 45
DMF / UF backwash, Sample drains, 1st & 2nd RO reject
(low pressure) 7.0 45 Desalinated water, potable water 7.0 45
RO cleaning solution 7.0 45 FeCl3 solution, NaOCl solution 7.0 45
Refer to Pipe Wall Thickness Calculation (10-TAA-P-71-001-001).
Pressure and Temperature Limits for CPVC Flange and Valve
Temp. (℃) 38 43 50
Press (Barg) 10.3 9.7 8.8
The specific pressure-temperature rating for valve shall be followed as per Manufacturer’s Pressure/Temperature limitation (Spears®, USA). The limitation shall be covered for the shown service‘s design condition.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/80 3.73
CPVC 4120 PE ASTM F441
5,6
20 S/80 3.91 5,6
25 S/80 4.55 5
40 S/80 5.08 5
50 S/80 5.54 5
80 S/80 7.62 5
100 S/80 8.56 5
150 S/80 10.97 5
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 150 SCH 80 CPVC 4120 SOCKET ASTM F439 2
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange All CL 150 CPVC SW, FF ASTM F439 ASME B16.5
Gasket All CL 150 EPDM 3.2 mmT, FF ASME B16.21
Bolt / Nut All A193 B8M CL 2 / A194 8M
Stud Bolt /Heavy Hex Nuts with 2-SS Washers
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
70/174
PIPING MATERIAL CLASS
AF2
Rating ASME Class 150
Material CPVC
Code ASME B31.1
Ball 15 ~50 CL 150 CPVC, FF, TE VBF-AP2
Diaphragm All CL 150 CPVC Body, PTFE Diaphragm, FF VDF-AP2
Butterfly 80 ~ 300 CL 150 CPVC, Wafer VFW-AP2
Check 15 ~ 50 CL 150 CPVC, EPDM seat Double Union, Ball Check FF VCF-AP2
80 ~ 300 CL 150 CPVC, Swing Type, FF VCF-AP2-1
Note:
1. CPVC : Chlorinated Polyvinyl Chloride (ASTM F441)
2. CPVC fittings shall be in accordance with ASTM F439-06 or equivalent.
3. CPVC pipe shall be handled, stored, and installed as per manufacturer recommendation.
4. For valves for pressure gauge (instrument), the screwed end type shall be applied..
5. The outside diameter dimensions of CPVC piping components shall be per Iron Pipe Size (IPS) system ASME B36.10.
6. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
71/174
PIPING MATERIAL CLASS
AG1
Rating ASME Class 150
Material GRP (polyester)
Code AWWA M45 / AWWA C950
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Circulating Water Supply / Discharge (U/G) 4.0+FV 40 / 45 Filtered/ Desalinated Water 10.0 40
FGD Seawater Supply 3.0+FV 40 Seawater Drain Sump Pump 10.0 40
Seawater Initial Supply 3.0+FV 40 CPP Regeneration Sump Pump 10.0 50
Other Auxiliaries Seawater Supply/ Discharge 10.0+FV 40 / 45 Chemical Waste Water 10.0 50
Tube Cleaning 10.0 45 Treated Chemical Waste Water 3.0 50
Desalinated Water Supply to Demi. Plant 7.0 40 BWRO Unit Outlet 5.0 40
CEDI Feed Pump 9.0 40 BWRO Flushing Pump 7.0 40
CEDI Unit Outlet 5.0 40 Sea Water, Filtered sea water 7.0 45
UF Permeate, 1st pass RO Permeate 7.0 45 DMF / UF backwash, Sample drains, 1st & 2nd
RO reject (low pressure) 7.0 45
Desalinated water 7.0 45 RO cleaning solution 7.0 45
The thickness shall be calculated with relevant code (AWWA M45) and GRP Manufacturer standard.
Pressure and Temperature Limits For valves up to DN150 (Based on ASME B16.34 -Group 2.8 Class 150)
Temp. (℃) 50 100
Press (Barg) 19.5 17.7
For Valves DN200 and above (Based on ASME B16.34 -Group 1.1 Class 150)
Temp. (℃) 50 100
Press (Barg) 19.2 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe 25 ~ 3600 Glass Reinforced Polyester
Double Bell Coupling for
Underground Manufacturer Standard 5
Butt Wrap Joint for Aboveground
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 3600 - Glass Reinforced Polyester
Double Bell Coupling for
Underground Manufacturer Standard
Butt Wrap Joint for Aboveground
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 300 CL 150 Glass Reinforced Polyester
FF ASME B16.5 4
350 ~ 600 CL 150 Glass Reinforced Polyester
Groove ASME B16.5
650 ~ 3600 CL 150 Glass Reinforced Polyester
Groove AWWA C207 CL. D
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
72/174
PIPING MATERIAL CLASS
AG1
Rating ASME Class 150
Material GRP (polyester)
Code AWWA M45 / AWWA C950
Gasket 25 ~ 300 CL 150 EPDM 3.2mm, Full Face
ASME B16.21 4
350 ~ 3600 CL 150 Rubber Ring O’Ring Gasket
Bolt / Nut ALL A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts/Washer with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS&Y, Solid Wedge Disc, FF,
VAF-CF10
80 ~ 200 CL 150 ASTM A995 CD3MN Body, SS S31803 Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC12
Globe 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS & Y, Plug Type Disc, FF
VGF-CF10
80 ~ 200 CL 150 ASTM A995 CD3MN Body, S31803 Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC12
Check
25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BC, Lift Type, FF VCF-CF10
80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Trim, Swing Type, FF VCF-AC12
200 ~ 600 CL 150 ASTM A216WCB with Rubber Lined Body, S31803 Trim, Dual Plate Type, FF
VCF-AC2-R
650 ~ 3600 CL 150 ASTM A216WCB with Rubber Lined Body, S31803 Trim, Dual Plate Type, FF
VCF-AC2-R1
Butterfly
80 ~ 150 CL 150 ASTM A995 CD3MN Body, SS31803 Disc, Eccentric Design, EPDM Seat, FF
VFF-AC12
200 ~ 600 CL 150 ASTM A216WCB with Rubber Lined Body & Disc, Eccentric Design, EPDM Seat, FF
VFF-AC2-R
650 ~ 3600 CL 150 ASTM A216WCB with Rubber Lined Body & Disc, Eccentric Design, EPDM Seat, FF
VFF-AC2-R1
Ball
25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-CF10
80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-AC12
Single Block 40 x 25 CL 600 ASTM A182 F51 Body, S31803 Trim, Floating Ball, FF x NPT VSM-CF10
Note:
1. To use GRP Piping above the ground shall be applied with UV protection..
2. The pipe shall be had a minimum stiffness of 2500 N/m2 in accordance with AWWA M45 and AWWA C950.
3. All materials used in the manufacture of pipe, fittings, and accessories shall conform to American Water Works Association, Fibreglass
Pipe Design AWWA M45.
4. The bolt drilling pattern of 600# flange can be used for valve connection.
5. For seawater conduits,
The GRP pipes shall be manufactured mainly with filament wound fibreglass and pure thermosetting resin. Sand as a filler is not permitted.
The use of ribs as stiffeners is also to be excluded unless the GRP is wholly surrounded by reinforced concrete.
The inner layer shall consist of pure resin equal to the type used for the structural wall. The thickness of the inner shall be at least 0.3 mm.
The piping shall have gasket-sealed joints formed by either bells and spigots or couplings. All gasketed joints shall be provided with double
gaskets to allow the integrity of the joint to be tested at the time of installation, before the pipe is buried. Each joint shall be capable of
watertight sealing and prefabricated in factory. The coupling joint shall be used as double bell coupler which is single gasket for each
connection side.
The GRP pipes that are not surrounded by reinforced concrete shall be designed for live loading to withstand 45 units (45 tonnes per axle)
of BS 5400 HB loading directly above the pipe within 30 metres (100 feet) of a structure and at road crossings. Alternatively spreader slabs
shall be provided or the pipes surrounded with concrete designed for the specified live loads.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
73/174
PIPING MATERIAL CLASS
AG2
Rating ASME Class 150
Material GRP (Vinlyester)
Code AWWA M45 / AWWA C950
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Hypochlorite Solution (NaOCl) 10.0 45 Acid Solution (HCl) 10.0 45
Electro-chlorination System Seawater Supply 10.0 + FV 40
The thickness shall be calculated with relevant code (AWWA M45) and GRP Manufacturer standard.
Pressure and Temperature Limits for Valves (Based on ASME B16.34 – Group 1.1 Class 150)
Temp. (℃) 50 100
Press (Barg) 19.2 17.7
Pressure and Temperature Limits for Butter fly Valves (Based on ASME B16.34 – Group 1.2 Class 150)
Temp. (℃) 50 100
Press (Barg) 19.5 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe 25 ~ 900 - - Glass Reinforced Vinlyester
Butt Wrap Joint Manufacturer
Standard
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 900 Glass Reinforced Vinlyester
Butt Wrap Joint Manufacturer
Standard
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 600 CL 150 Glass Reinforced
Vinlyester FF or Groove ASME B16.5
650 ~ 900 CL 150 Glass Reinforced
Vinlyester Groove AWWA C207 CL.D
Gasket 25 ~ 300 CL 150 EPDM 3.2mm, Full Face
ASME B16.21
350 ~ 900 CL 150 Rubber Ring O’Ring Gasket
Bolt / Nut ALL A193-B7 / A194-2H
Stud Bolt /Heavy Hex Nuts/Washer with Aluminum Ceramic Coating ASME B1.1
/ASME B18.2.2
Stud Bolt /Heavy Hex Nuts/Washer with Hot Dip Galvanized
4
Valves
Item Size (DN) Rating Description Material Code Note
Diaphragm ~ 200 CL 150 A216WCB with Rubber lined (Diaphragm: EPDM), FF VDF-AC2
Butterfly 25 ~ 900 CL 150 A216 WCC body, Seat: Rubber or PTFE equivalent, Disc: cast steel + PTFE equivalent (Halar coating), wafer(Lug)
VFW-AC3
Check 25 ~ 300 CL 150 A216 WCB body, Seat: Rubber or PTFE equivalent, Ball/Swing/Butterfly (Dual Plate), FF
VCF-AC2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
74/174
PIPING MATERIAL CLASS
AG2
Rating ASME Class 150
Material GRP (Vinlyester)
Code AWWA M45 / AWWA C950
Note:
1. To use GRP Piping above the ground shall be applied with UV protection..
2. The pipe shall be had a minimum stiffness of 2500 N/m2 in accordance with AWWA M45 and AWWA C950.
3. All materials used in the manufacture of pipe, fittings, and accessories shall conform to American Water Works Association, Fibreglass
Pipe Design AWWA M45.
4. The bolting can be used for electro-chlorination system (vendor package, inside building).
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
75/174
PIPING MATERIAL CLASS
AG3
Rating ASME Class 150
Material GRP (Epoxy)
Code AWWA M45 / AWWA C950
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Quenching Sump Pump Discharge 10.0 100
The thickness shall be calculated with relevant code (AWWA M45) and GRP Manufacturer standard.
Pressure and Temperature Limits for Valves (Based on ASME B16.34 - Group 2.8 Class 150)
Temp (℃) 50 100
Press (Barg) 19.5 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe 25 ~ 250 - - GRE
Butt Wrap Joint
Or
Bell and Spigot Adhesive Bonded
Joint
Manufacturer
Standard
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 250 GRE
Butt Wrap Joint
Or
Bell and Spigot Adhesive Bonded
Joint
Manufacturer
Standard
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 250 CL.150 GRE FF ASME B16.5 4
Gasket 25 ~ 250 CL.150 Choroprene Rubber +
Cotton Insertion 3.2mm, Full Face ASME B16.21
Bolt / Nut ALL A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts/washer with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Globe 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS & Y, Plug Type Disc, FF
VGF-CF10
80 ~ 200 CL 150 ASTM A995 CD3MN Body, S31803 Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC12
Check 25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BC, Lift Type, FF VCF-CF10
80 ~ 250 CL 150 ASTM A995 CD3MN Body, S31803 Trim, Swing Type, FF VCF-AC12
Single Block 25 x 25 CL 600 ASTM A182 F51 Body, S31803 Trim, Floating Ball, FF x NPT VSM-CF10
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
76/174
PIPING MATERIAL CLASS
AG3
Rating ASME Class 150
Material GRP (Epoxy)
Code AWWA M45 / AWWA C950
Note:
1. To use GRP Piping above the ground shall be applied with UV protection.
2. The pipe shall be had a minimum stiffness of 2500 N/m2 in accordance with AWWA M45 and AWWA C950.
3. All materials used in the manufacture of pipe, fittings, and accessories shall conform to American Water Works Association,
Fibreglass Pipe Design AWWA M45.
4. The bolt drilling pattern of 600# flange can be used for valve connection.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
77/174
PIPING MATERIAL CLASS
AG4
Rating ASME Class 150
Material GRP (polyester)
Code AWWA M45 / AWWA C950
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Desalinated Water Supply to Demi. Plant 7.0 40 CIP Process 5.0 40
CEDI Feed Pump 9.0 40 BWRO Unit Outlet 5.0 40
CEDI Unit Outlet 7.0 40 BWRO Flushing Pump 7.0 40
The thickness shall be calculated with relevant code (AWWA M45) and GRP Manufacturer standard.
Pressure and Temperature Limits For valves (Based on ASME B16.34 -Group 2.3 Class 150)
Temp. (℃) 50 100
Press (Barg) 15.3 13.3
Note. The pressure and temperature limits for casting valve (Group 2.2 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe 25 ~ 300 Glass Reinforced Polyester
Butt Wrap Joint Manufacturer Standard
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 300 Glass Reinforced Polyester
Butt Wrap Joint Manufacturer Standard
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 300 CL 150 Glass Reinforced Polyester
FF ASME B16.5 4
Gasket 25 ~ 300 CL 150 EPDM 3.2mm, Full Face ASME B16.21
Bolt / Nut ALL A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts/Washer with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Globe 25 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, FF
VGF-CF6
80 ~ 300 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC7-1
Check 25 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, FF VCF-CF6
80 ~ 300 CL 150 ASTM A351 CF3M Body, PTFE trim, BC, Spring wafer or Twin Plate NRV Type, FF
VCF-AC7-1
Butterfly 80 ~ 300 CL 150 ASTM A351 CF3M Body, Eccentric Design, EPDM Seat, ASME B16.5, Wafer lug or FF
VFW-AC7 5
Ball 25 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-CF6
Diaphragm 20 ~ 200 CL 150 A216 WCB with Rubber lined (Diaphragm: EPDM), FF VDF-AC2-R
Stop Check 25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Y-Type, FF
VTF-CF6
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
78/174
PIPING MATERIAL CLASS
AG4
Rating ASME Class 150
Material GRP (polyester)
Code AWWA M45 / AWWA C950
Note:
1. To use GRP Piping above the ground shall be applied with UV protection..
2. The pipe shall be had a minimum stiffness of 2500 N/m2 in accordance with AWWA M45 and AWWA C950.
3. All materials used in the manufacture of pipe, fittings, and accessories shall conform to American Water Works Association, Fibreglass
Pipe Design AWWA M45.
4. The bolt drilling pattern of 600# flange can be used for valve connection.
5. Flange type is used from GTMDO unit to discharge line.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
79/174
PIPING MATERIAL CLASS
AG5
Rating ASME Class 150
Material GRP (Epoxy)
Code AWWA M45 / AWWA C950/NFPA
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Fire Fighting (U/G, GIS Area) 14.5 58
The thickness shall be calculated with relevant code (AWWA M45) and GRP Manufacturer standard.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe 80 ~ 250 - - GRE Bell and Spigot Adhesive Bonded
Joint
Manufacturer
Standard
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
80 ~ 250 GRE Bell and Spigot Adhesive Bonded
Joint
Manufacturer
Standard
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 80 ~ 250 CL.150 GRE FF ASME B16.5
Gasket 80 ~ 250 CL.150 Choroprene Rubber +
Cotton Insertion 3.2mm, Full Face ASME B16.21
Bolt / Nut ALL A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts/Washer with Hot Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Note:
1. GRE materials for firefighting shall be UL listed or FM approved and design shall comply with the requirements of NFPA-24.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
80/174
PIPING MATERIAL CLASS
AH1
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1 / AWWA
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Circulating Water Supply (A/G) 4.0+FV 40 FGD Seawater Supply Pump Discharge 3.0+FV 40
Circulating Water Discharge (A/G)
From Pump Discharge to Discharge Header 4.0+FV 45 Seawater Pipeline Filling Pump Discharge 3.0+FV 40
Circulating Water Pump Discharge 4.0+FV 40 Other Auxiliaries Seawater Supply Pump 10.0+FV 40
CPP general chemical drains 10.0 50 Seawater Absorber Pump Discharge 3.5+FV 60
The pipe wall thickness is calculated based on the following design condition.
- DN25 ~ DN450 : 10.0 Barg +FV& 40 ℃
- DN500 ~ DN3600 : 4.0+FV Barg & 45 ℃ Pipe wall thickness under external pressure is verified. For pipe DN750 and above, the stiffness ring is requested. Please refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For “Valves DN200 and above” and “Flanges up to DN600 “ (Based on ASME B16.5 -Group 1.1 Class 150)
Temp (℃) 50 100
Press (Barg) 19.2 17.7
For Flanges between DN650 and DN3600 (Based on AWWA C207 CL-D) The flange are suitable for pressure rating : 10.34barg (1034kpa)
For valves up to DN150 (Based on ASME B16.34 -Group 2.8 Class 150)
Temp (℃) 50 100
Press (Barg) 19.5 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A790-S31803 SMLS. PE ASME B36.19/
ASTM A790
40 S/40S 3.68
50 S/40S 3.91
50 S/80 5.54
ASTM A106 Gr.B
Rubber Lined , SMLS, PE
ASME B36.10
4
65 S/STD 5.16
SMLS, BE
Rubber Lined
1
80 S/STD 5.49 1
100 S/STD 6.02 1
150 S/STD 7.11 1
200 S/STD 8.18 1
250 S/STD 9.27 1
300 ~ 600 S/STD 9.53 1
650 ~ 800 S/STD 9.53 ASTM A134 A285C EFW, Rubber Lined 1
1850 ~
2400 - 14.00
A516 Gr.60 Fabricated, Rubber Lined 1
2550~ 3450 - 18.00 1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
81/174
PIPING MATERIAL CLASS
AH1
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1 / AWWA
Common Header
Item Size (DN) THK (mm) Material Description Note
Common Header for Circulating Seawater Pump Discharge DN3600 28mmt A516 Gr.60 Fabricated, Rubber Lined 1,5
Common Header for FGD Seawater Pump Discharge DN2550 24mmt A516 Gr.60 Fabricated, Rubber Lined 1,5
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F51 Forged End, SW ASME B16.11
65 ~ 600 ASTM A234 WPB SMLS, BW Rubber Lined
ASME B16.9 Schedule Match Pipe
1,3
650 ~ 800 ASTM A234 WPB Welded, BW Rubber Lined
ASME B16.9 Schedule Match Pipe
1,2,3
Elbow/Tee 2250 ~3600 ASTM A516 Gr.60 Fabricated Welded, BW
Rubber Lined 1,5
Weldolet 50 ~ - ASTM A105 Forged End, BW MSS SP- 97 4
Plate A285 Gr.C or A516 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 150 ASTM A182 F51 SO FF ASME B16.5
25 ~ 50 CL 600 ASTM A182 F51 SO FF ASME B16.5 6
50 CL 150 ASTM A105 SO FF ASME B16.5 4
50 CL 600 ASTM A105 SO FF ASME B16.5 6
65 ~ 600 CL 150 ASTM A105
SO FF, Rubber Lined ASME B16.5 1
650 ~ 3600 AWWA
C207 CL-D Ring Type FF Rubber Lined
AWWA C207 CL. D 1
Gasket 25 ~ 600 CL 150 EPDM 3.2mmT, Full Face
ASME B16.21
650 ~ 3600 AWWA C207 CL-D
Rubber (Insert Steel) 8.0mmT, FF Flat Ring
Bolt / Nut All A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS&Y, Solid Wedge Disc, FF
VAF-CF10
80 ~ 200 CL 150 ASTM A995 CD3MN Body, SS S31803 Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC12
Globe 25 ~ 50 CL 600
ASTM A182 F51 Body, S31803 Trim, BB, OS & Y, Plug Type Disc, FF
VGF-CF10
80 ~ 200 CL 150 ASTM A995 CD3MN Body, S31803 Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC12
Check
25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BC, Lift Type, FF VCF-CF10
80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Trim, Swing Type, FF VCF-AC12
200 ~ 600 CL 150 ASTM A216WCB with Rubber lined Body, S31803 Trim, Dual Plate Type, FF
VCF-AC2-R
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
82/174
PIPING MATERIAL CLASS
AH1
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1 / AWWA
650 ~ 3600 CL 150 ASTM A216WCB with Rubber lined Body, S31803 Trim, Dual Plate Type, FF
VCF-AC2-R1
Butterfly
80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Disc, Eccentric Design, EPDM Seat, FF
VFF-AC12
200 ~ 600 CL 150 ASTM A216WCB with Rubber Lined Body & Disc, Eccentric Design, EPDM Seat, FF
VFF-AC2-R
650 ~ 3600 CL 150 ASTM A216WCB with Rubber Lined Body & Disc, Eccentric Design, EPDM Seat, FF
VFF-AC2-R1
Single Block 50 x 25 CL 600 ASTM A182 F51 Body, S31803 Trim, Floating Ball, FF x NPT VSM-CF10
Ball 80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Trim, RTFE Seat, Side Entry, Floating Ball, FF
VBF-AC12
Note:
1. The carbon steel piping and fitting shall be internally rubber lined in accordance with rubber lining procedure (S-00-TAA-P-46-003-001) and the minimum rubber lined thickness shall be 3.0mm.
2. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
3. Schedule (thickness) shall be equal to or greater than that of pipe.
4. The carbon steel material up to DN50 shall be used only for header pipe’s attached nozzle and the nozzle attached to main header pipe (DN65 & larger) shall be fabricated as internally rubber lined.
5. The strength calculation shall be carried out as per detail design.
6. The 600# flange can be used for valve connection.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
83/174
PIPING MATERIAL CLASS
AH2
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Fire Fighting (For Sea Water) 14.5 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Valves and flanges upto DN50 (Based on ASME B16.34/B16.5 - Group 2.8 Class 150)
Temp (℃) 50 100
Press (Barg) 19.5 17.7
For Flanges DN65 and above (Based on ASME B16.34 - Group 1.1 Class 150)
Temp (℃) 50 100
Press (Barg) 19.2 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A790-S31803 SMLS. PE ASME B36.19/
ASTM A790
40 S/40S 3.68
50 S/40S 3.91
50 S/80 5.54
ASTM A106 Gr.B
Rubber Lined, SMLS, PE
ASME B36.10
3
65 S/STD 5.16
SMLS. BE
Rubber Lined
1
80 S/STD 5.49 1
100 S/STD 6.02 1
150 S/STD 7.11 1
200 S/STD 8.18 1
250 S/STD 9.27 1
300 ~ 400 S/STD 9.53 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F51 Forged End, SW ASME B16.11
65 ~ 400 ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1,3
Weldolet 50 ~ - ASTM A105 Forged End, BW MSS SP- 97 3
Plate A285 Gr.C
Flange, Gasket & Bolt / Nut
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
84/174
PIPING MATERIAL CLASS
AH2
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 150 ASTM A182 F51 SO FF
ASME B16.5
25 ~ 50 CL 600 ASTM A182 F51 SO FF 4
50 CL 150 ASTM A105 SO FF, Rubber Lined 3
50 CL 600 ASTM A105 SO FF, Rubber Lined 4
65 ~ 400 CL 150 ASTM A105 SO FF, Rubber Lined 1
Gasket 25 ~ 400 CL 150 EPDM 3.2mmT, Full Face ASME B16.21
Bolt / Nut All A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Globe 25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BB, OS & Y, Plug Type Disc, FF
VGF-CF10
Check
25 ~ 50 CL 600 ASTM A182 F51 Body, S31803 Trim, BC, Lift Type, FF VCF-CF10
80 ~ 150 CL 150 ASTM A995 CD3MN Body, S31803 Trim, Swing Type, FF VCF-AC12
200 ~ 400 CL 150 ASTM A216WCB with Rubber lined Body, S31803 Trim, Dual Plate Type, FF
VCF-AC2-R
Butterfly 80 ~ 150 CL 150
ASTM A995 CD3MN Body, S31803 Disc, Eccentric Design, EPDM Seat, FF
VFF-AC12
200 ~ 400 CL 150 ASTM A216WCB with Rubber Lined Body & Disc, Eccentric Design, EPDM Seat, FF
VFF-AC2-R
Note:
1. The carbon steel piping and fitting shall be internally rubber lined in accordance with rubber lining procedure (S-00-TAA-P-46-003-001) and the minimum rubber lined thickness shall be 3.0mm.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The carbon steel material up to DN50 shall be used only for header pipe’s attached nozzle and the nozzle attached to main header pipe (DN65 & larger) shall be fabricated as internally rubber lined.
4. The 600# flange can be used for valve connection.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
85/174
PIPING MATERIAL CLASS
AH3
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Make Up Water(Condensate Pump) 10.0 50 Make-Up Water (Boiler/Deaerator filling pump) 13.0 50
Make Up Water to Demi. Plant 10.0 50 Demineralized Water 10.0 40
Dilute sulphuric acid (5%) 10.0 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Valves and flanges upto DN50 (Based on ASME B16.34/B16.5 - Group 2.3 Class 150)
Temp (℃) 50 100
Press (Barg) 15.3 13.3
For Flanges DN65 and above (Based on ASME B16.5 - Group 1.1 Class 150)
Temp (℃) 50 100
Press (Barg) 19.2 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A312 TP316L SMLS, PE ASME B36.19
40 S/40S 3.68
50 S/40S 3.91
50 S/80 5.54
ASTM A106 Gr.B
Rubber Lined ,SMLS, PE
ASME B36.10
3
65 S/STD 5.16
SMLS, BE
Rubber Lined ,
1
80 S/STD 5.49 1
100 S/STD 6.02 1
150 S/STD 7.11 1
200 S/STD 8.18 1
250 S/STD 9.27 1
300 ~ 400 S/STD 9.53 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW ASME B16.11
65 ~ 400 - ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1,3
Weldolet 50 ~ - ASTM A105 Forged End, BW MSS SP- 97
Plate A285 Gr.C
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
86/174
PIPING MATERIAL CLASS
AH3
Rating ASME Class 150
MaterialCarbon Steel
(Internal Rubber Lined)
Code ASME B31.1
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 150 ASTM A182 F316L SO FF
ASME B16.5
25 CL 600 ASTM A182 F316L SO FF 4
50 CL 150 ASTM A105 SO FF, Rubber Lined 3
50 CL 600 ASTM A105 SO FF, Rubber Lined 4
65 ~ 400 CL 150 ASTM A105 SO FF, Rubber Lined 1
Gasket 25 ~ 400 CL 150 EPDM 3.2mmT, Full Face ASME B16.21
Bolt / Nut 25 ~ 50 CL 150
A193 B8M CL 2 / A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
65 ~ 400 A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF6
80 ~ 400 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Flexible Wedge Disc, FF
VAF-AC7-1 6
Globe 25 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF6
80 ~ 400 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Cone Type Disc, FF
VGF-AC7-1 6
Check
25 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, SW VCS-CF6
80 ~ 400 CL 150 ASTM A351 CF3M Body, SS 316L Trim, BC, Swing Type, FF
VCF-AC7-1
80 ~ 400 CL 150 ASTM A351 CF3M Body, PTFE lining and trim, BC, Spring wafer NRV Type, RF
VCF-AC7-T 5
Ball 25 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, RTFE Seat, Side Entry, Floating Ball, with 75mm S/40S Nipples, SW
VBS-CF6
Butterfly
80 ~ 400 CL 150 ASTM A351-CF3M Body, Eccentric Design, EPDM or PTFE Seat, ASME B16.5, FF
VFF-AC7-1 7
80 ~ 100 CL 150 ASTM A216 WCB, ASTM CF8M disc Halar coated, EPDM Seat, ASME B16.5, FF
VFF-AC2-R 5
Single Block 50 x 25 CL 600 ASTM A182 F316L Body, SS 316L Trim, Floating Ball, FF x NPT
VSM-CF6
Note:
1. The carbon steel piping and fitting shall be internally rubber lined in accordance with rubber lining procedure (S-00-TAA-P-46-003-001) and the minimum rubber lined thickness shall be 3.0mm.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The carbon steel material up to DN50 shall be used only for header pipe’s attached nozzle and the nozzle attached to main header pipe (DN65 & larger) shall be fabricated as internally rubber lined.
4. The 600# flange only uses for single block valve connection.
5. The valve type can be used for condensate polishing plant such as dilute sulphuric acid (5%).
6. The suffix ‘-W’ shall be added to valve material code when water seal is applied.
7. PTFE Seat for the butterfly valve shall be used for demineralized treatment plant.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
87/174
PIPING MATERIAL CLASS
AH5
Rating ASME Class 150
MaterialCarbon steel
(Internal PTFE Lined)
Code ASME B31.1
Service D.P.
(Barg)D.T.(℃)
Service D.P.
(Barg) D.T. (℃)
Chemical Dosing (H2SO4) for Waste Water Treatment System 10.0 50 Chemical Dosing (H2SO4) for CPP 10.0 50
Chemical Dosing (H2SO4) for Desalination 10.0 55
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits (Based on ASME B16.34 - Group 1.1 Class 150)
Temp (℃) 50 100
Press (Barg) 19.2 17.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40 2.77
ASTM A106 Gr.B
SMLS, PE
PTFE Lined
ASME B36.10
20 S/40 2.87
25 S/40 3.38
40 S/40 3.68
50 S/40 3.91
65 S/40 5.16
SMLS, BE
PTFE Lined
80 S/40 5.49
100 S/40 6.02
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
20 ~ 50 CL.3000 ASTM A105 Forged End, SW PTFE Lined
ASME B16.11
65 ~ 100 ASTM A234WPB SMLS, BW PTFE Lined
ASME B16.9 Schedule Match Pipe
1,3
Weldolet 50 ~ - ASTM A105 Forged End, BW MSS SP- 97
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 20 ~ 100 CL 150 ASTM A105 SO RF, PTFE Lined ASME B16.5
Gasket 20 ~ 100 CL 150 PTFE Envelope (EPDM
Cushion) 3.2mmT RF ASME B16.21
Bolt / Nut All A193-B7 / A194-2H Stud Bolt /Heavy Hex Nuts with Hot Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
88/174
PIPING MATERIAL CLASS
AH5
Rating ASME Class 150
MaterialCarbon steel
(Internal PTFE Lined)
Code ASME B31.1
Item Size (DN) Rating Description Material Code Note
Check ~ 400 CL 150 ASTM A216 WCB PTFE Lined Body, PTFE Trim, BC, Lift Type, RF
VCF-AC2-T
Ball ~ 400 CL 150 ASTM A216 WCB PTFE Lined Body, C.S Teflon Lining Trim, PTFE Seat, Side Entry, Floating Ball, RF
VBF-AC2-T
Plug ~ 400 CL 150. ASTM A216 WCB PTFE Lined Body, Plug, RF VPF-AC2-T
Diaphragm CL 150. ASTM A216 WCB PTFE Lined Body, PTFE Diaphragm, BB, RF
VDF-AC2-T
Butterfly 80 CL 150 ASTM A216 Body, PTFE Lined Body & Disc, ASME B16.5, RF VFF-AC2-T
Note:
1. One of two sides is fixed flange, the other side is lap joint flange.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The minimum 3.0mmT Teflon lined shall be applied.
4. The carbon steel piping and fitting shall be internally PTFE lined.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
89/174
PIPING MATERIAL CLASS
BA1
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T.(℃)
Service D.P.
(Barg) D.T. (℃)
Aux. Steam 20.0 300 Steam Transformer Feed Pump Discharge 24.0 150
IP Turbine Exhaust Steam to Deaerator 10.0+FV 399 Aux. Steam HDR Drain 20.0 300
LP Turbine Extraction Steam to LP Heater #4 10.0+FV 350 BFW Pump Minimum flow 16.0 200
Feed Water Booster Pump Suction 14.0+FV 200 BFW Pump PSV Outlet 16.0 200
HP Steam PSV & ERV Vent 20.0 390 Secondary Steam 15+FV 205
Cold Reheat Steam to Aux.Steam HDR (PCV Disch.) 20.0 365
The pipe wall thickness is calculated based on the following design condition
- DN25 ~ DN250: 24.0 Barg & 150 ℃ / 20 Barg & 390℃
- DN300 ~ DN800: 20.0 Barg & 300 ℃
Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/B16.47 - Group 1.1 Class 300)
Temp (℃) 150 200 250 300 325 350 400
Press (Barg) 45.1 43.8 41.9 39.8 38.7 37.6 34.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/ 80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/ 80 5.08
50 S/ 80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
125 S/STD 6.55
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 600 S/STD 9.53
650 ~ 800 S/STD 9.53 ASTM A672 B60 CL.12 EFW, BE 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 600 ASTM A234WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
650 ~ 800 ASTM A234WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
90/174
PIPING MATERIAL CLASS
BA1
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 300
ASTM A105
SW RF ASME B16.5
65 ~ 600 CL 300 WN RF ASME B16.5
650 ~ 800 CL 300 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 600 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
650 ~ 800 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1
80 ~ 800 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-BC2 4,5
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 3
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1
80 ~ 800 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-BC2
Check
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 300 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-BC2
650~800 CL 300 ASTM A216 WCB Body, 13Cr Trim, BC, Dual plate, Flanged Type B16.47 Ser-A, RF
VCF-BC2-1
Needle 25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Needle Disc, SW VNS-CF1
80 ~ 800 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Needle Disc, BW
VNB-BC2
Angle 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BB, OS&Y, Angle Type, SW VLS-CF1
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
4. The suffix ‘-L’ shall be added to valve material code when limit switch is applied
5. The suffix ‘-W’ shall be added to valve material code when water seal is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
91/174
PIPING MATERIAL CLASS
BA2
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
CEP Discharge 39.0+FV 85 CEP Discharge Heating(LP Heater No.4) 39.0+FV 170
Primary Condensate Pump Discharge 30.0 205 Condensate LP Heater #4 to Deaerator 39.0+FV 200
HP Heater #6 Cascade Drain 26.0+FV 240 LP Forward Heater Pump Discharge 39.0+FV 150
CEP Discharge Heating (LP Heater No.3) 39.0+FV 150 Boiler Flash Tank Vent 10.0 375
CPP Inlet & Bypass 39.0+FV 85
The pipe wall thickness is calculated based on the following design condition
- DN25 ~ DN550: 39.0 Barg+FV & 200 ℃
- DN1050: 10.0barg & 375 ℃ (For Flash Tank Vent)
Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/B16.47 - Group 1.1 Class 300)
Temp (℃) 150 200 250 300 325 350 400
Press (Barg) 45.1 43.8 41.9 39.8 38.7 37.6 34.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/ 80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/ 80 5.08
50 S/ 80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 S/STD 9.53
350 S/STD 9.53
400 S/XS 12.70
450 ~ 500 S/XS 12.70
550 - 15.88
1050 S/STD 9.53 ASTM A672 B60 CL.12 EFW, BE 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow 25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
92/174
PIPING MATERIAL CLASS
BA2
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Tee Reducer Cap
65 ~ 550 ASTM A234WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
1050 ASTM A234WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 300
ASTM A105
SW RF ASME B16.5
65 ~ 550 CL 300 WN RF ASME B16.5
1050 CL 300 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 550 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20/
B16.21
25 ~ 550 CL 300 Klingersil C4430 3mm T Synthetic fiber / NBR 4
1050 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1
80 ~ 550 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-BC2 5,6
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 3
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1
80 ~ 550 CL 300 ASTM A216WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-BC2 6
Check 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 550 CL 300 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-BC2
Butterfly 80 ~ 550 CL 300 ASTM A216 WCB Body, ASTM CF8M Disc, lugged pattern RTFE/PTFE seat, RF
VFF-BC2 4
Ball 25 ~ 50 CL 600
ASTM A105 Body, SS304 Trim, RTFE Seat, Full Port, Side Entry, Floating Ball with 75mm S/80 Nipple, SW
VBS-CF1
80 ~ 550 CL 300 ASTM A216 WCB Body, A105+ENP or SS 304 Trim, RTFE Seat, Side Entry, Floating Ball, RF
VBF-BC2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
93/174
PIPING MATERIAL CLASS
BA2
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
4. The gasket and valve type can be used for condensate polishing plant (vendor package) such as CPP inlet & bypass lines.
5. The suffix ‘-L’ shall be added to material code when limit switch is applied.
6. The suffix ‘-W’ shall be added to material code when water seal is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
94/174
PIPING MATERIAL CLASS
BA3
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HFO/HCO Unloading Line 15.0 85 DFO Forwarding Pump For Others Discharge 40.0 150
HFO/HCO Pump Discharge(To Each Boiler) 41.0 150 HFO/HCO Recirculation Piping 40.0 150
DFO Forwarding Pump For Boiler Discharge 43.0 150
The pipe wall thickness is calculated based on the following design condition
- DN25 ~ DN500: 43.0 Barg & 150 ℃
- DN650 ~ DN1200: 15.0 Barg & 85 ℃ (For HFO/HCO unloading Line)
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/16.47 - Group 1.1 Class 300)
Temp (℃) 150 200 250 300 325 350 375 400
Press (Barg) 45.1 43.8 41.9 39.8 38.7 37.6 36.4 34.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/ 80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/ 80 5.08
50 S/ 80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 S/STD 9.53
350 S/STD 9.53
400 ~ 500 S/XS 12.70
650~700 S/STD 9.53 API 5L Gr.B EFW, BE
1
1200 S/XS 12.70 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 600 - ASTM A234WPB SMLS, BW ASME B16.9 Schedule Match Pipe
2
650 ~ 1200 - ASTM A234WPB Welded, BW ASME B16.9 Schedule Match Pipe
1,2
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
95/174
PIPING MATERIAL CLASS
BA3
Rating ASME Class 300
Material Carbon Steel
Code ASME B31.1
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 300 ASTM A105 SW RF ASME B16.5
65 ~ 600 CL 300 ASTM A105
WN RF ASME B16.5
650 ~ 1200 CL 300 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 600 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
650 ~ 1200 CL 300 316 SS Strip with Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1 4
80 ~ 1200 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-BC2 4, 5
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type disc, SWxNPT
VGZ-CF1 3,4
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1 4
80 ~ 600 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Cone Type Disc, BW
VGB-BC2 4
Check
25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1 4
80 ~ 600 CL 300 ASTM A216 WCB Body, 13Cr Trim, BC, Swing Type, BW VCB-BC2 4
650 ~ 1200 CL 300 ASTM A216 WCB Body, 13Cr Trim, BC, Dual plate, Flanged Type B16.47 Ser-A, RF
VCF-BC2-1
Ball
25 ~ 50 CL 600 ASTM A105 Body, SS 304 Trim, RTFE Seat, Floating Ball, Full Port, Top Entry, with 75mm S/80 Nipple, SW
VBS-CF1-1 4
80 ~ 100 CL 300 ASTM A216WCB Body, ASTM A105+ENP or SS 304 Trim, BB, RTFE Seat, Top entry, Floating Ball, Full port, BW
VBB-BC2 4
150 ~ 1200 CL 300 ASTM A216WCB Body, ASTM A105+ENP or SS 304 Trim, BB, RTFE Seat, Top entry, Trunnion Ball, Full port, BW
VBB-BC2-1 4
Needle 25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Needle Disc, SW VNS-CF1 4
80 ~ 600 CL 300 ASTM A216 WCB Body, 13Cr Trim, BB, OS&Y, Needle Disc, BW
VNB-BC2 4
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The end type valve (SWxNPT) shall be used for instrument root valve.
4. All equipment nozzles and control valve connection shall be furnished with flanged end type. In addition, the end type of motor operated valve shall be also flange type in fuel oil metering package.
5. The suffix ‘-L’ shall be added to material code when limit switch is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
96/174
PIPING MATERIAL CLASS
BB1
Rating ASME Class 300
Material Low Alloy Steel (P22)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Leak-Off Steam 10.0+FV 540 Hot Rehear PSV Vent 10.0 517
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 Group 1.10 Class 300)
Temp (℃) 450 475 500 538 550
Press (Barg) 33.7 31.7 28.2 18.4 15.6
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr.P22
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/80 7.01
SMLS, BE
80 S/80 7.62
100 S/40 6.02
150 S/40 7.11
200 S/40 8.18
250 S/40 9.27
550 S/STD 9.53
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F22 CL.3 Forged End, SW ASME B16.11
65 ~ 550 ASTM A234 WP22 CL.3 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F22 CL.3 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F22 CL.3 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F22 CL.3 Forged End, SW -
Plate A387 Gr22
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 300 ASTM A182 F22 CL.3 SW RF ASME B16.5
65 ~ 550 CL 300 ASTM A182 F22 CL.3 WNRF ASME B16.5
Gasket All CL 300 316 Strip with Graphite & MICA
Spiral Wound, SS Outer Ring 4.5mmT, RF
ASME B16.20
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
97/174
PIPING MATERIAL CLASS
BB1
Rating ASME Class 300
Material Low Alloy Steel (P22)
Code ASME B31.1
Bolt / Nut All A193-B16 / A194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600 ASTM A182 F22 CL.3 Body, F22 Trim, BB, OS&Y, Solid
Wedge Disc, SW VAS-CF4
80 ~ 550 CL 300 ASTM A217 WC9 Body, F22 Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-BC6 3,4
Globe 25 ~ 50 CL 600 ASTM A182 F22 CL.3 Body, F22 Trim, BB, OS&Y, Plug
Type Disc, SW VGS-CF4
80 ~ 550 CL 300 ASTM A217 WC9 Body, F22 Trim, BB, OS&Y, Cone Type Disc, BW
VGB-BC6 3,4
Check 25 ~ 50 CL 600 ASTM A182 F22 CL.3 Body, F22 Trim, BC, Lift Type, SW VCS-CF4
80 ~ 550 CL 300 ASTM A217 WC9 Body, F22 Trim, BC, Tilting Type, BW VCB-BC6 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
98/174
PIPING MATERIAL CLASS
BB2
Rating ASME Class 300
Material Low Alloy Steel (P11)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Superheater Steam (Steam Turbine) 10 499 IP Extraction Steam (To External Desuperheater) 26+FV 450
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 Group 1.9 Class 300)
Temp (℃) 400 425 450 475 500
Press (Barg) 36.5 35.2 33.7 31.7 25.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr.P11
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 ~ 400 S/STD 9.53
450 ~ 600 S/XS 12.7
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW ASME B16.11
65 ~ 600 ASTM A234 WP11 CL.2 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F11 CL.2 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW -
Plate A387 Gr11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 300 ASTM A182 F22 CL.3 SW RF ASME B16.5
65 ~ 550 CL 300 ASTM A182 F22 CL.3 WNRF ASME B16.5
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
99/174
PIPING MATERIAL CLASS
BB2
Rating ASME Class 300
Material Low Alloy Steel (P11)
Code ASME B31.1
Gasket All CL 300 316 Strip with Graphite & MICA
Spiral Wound, SS Outer Ring 4.5mmT, RF
ASME B16.20
Bolt / Nut All A193-B16 / A194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate
25 ~ 50 CL 600 ASTM A182 F11 CL.2 Body, F11 Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF4
80 ~ 600 CL 300 ASTM A217 WC6 Body, F11 Trim, BB, OS&Y, Flexible Wedge Disc, BW
VAB-BC6 3,4
Globe 25 ~ 50 CL 600 ASTM A182 F11 CL.2 Body, F11 Trim, WB, OS&Y, Plug Type
Disc, SW VGS-CF4
80 ~ 600 CL 300 ASTM A217 WC6 Body, F11 Trim, BB, OS&Y, Cone Type Disc, BW
VGB-BC6 3,4
Check 25 ~ 50 CL 600 ASTM A182 F11 CL.2 Body, F11 Trim, WC, Lift Type, SW VCS-CF4
80 ~ 600 CL 300 ASTM A217 WC6 Body, F11 Trim, BC, Tilting Type, BW VCB-BC6 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
100/174
PIPING MATERIAL CLASS
BC1
Rating ASME Class 300
Material Stainless Steel (316L)
Code ASME B31.1 / ASME B31.3
Service D.P.(Bar
g)
D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Service Water (From Service Water Pump To Boiler Area)
15.0 60 Chemical Dosing (Steam Transformer/ Aux. Boiler) 15.0 85
Boiler Wash Water 15.0 80 Urea Solution(Urea Injection Skid) 20.0 85
1st SWRO permeate 15.0 65 Urea Solution(Urea Hydrolyzer Skid) 19.0 163
Sampling (Aux. Boiler) 25.0 226 Chemical Dosing (Oxygen Dosing ,to BFP suction) 25.0 60
Chemical Dosing piping system shall be applied in accordance with ASME B31.3.
The pipe wall thickness is calculated based on the following design condition.
- DN15 ~ DN200: 25.0 Barg & 85 ℃
- DN250: 15.0barg & 60 ℃ (For Service Water)
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 300)
Temp (℃) 50 100 150 200 250 300
Press (Barg) 40.0 34.8 31.4 29.2 27.5 26.1
Note. The pressure and temperature limits for casting valve (Group 2.2 Class 150) are higher than the shown limitation above.
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316L
SMLS, PE
ASME B36.19
2
20 S/40S 2.87 2
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
SMLS, BE
80 S/40S 5.49
100 S/40S 6.02
150 S/40S 7.11
200 S/40S 8.18
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW ASME B16.11
65 ~ 200 ASTM A403 WP316L SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F316L Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F316L Forged End, SW -
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
101/174
PIPING MATERIAL CLASS
BC1
Rating ASME Class 300
Material Stainless Steel (316L)
Code ASME B31.1 / ASME B31.3
Plate A240 Gr.316L
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 300
ASTM A182 F316L SW RF
ASME B16.5 2
65 ~ 200 CL 300 WN RF
Gasket All CL 300 316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF6
80 ~ 200 CL 300 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-BC7
Globe
15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF6
25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF6
80 ~ 200 CL 300 ASTM A351 CF3M Body, SS 316L Trim, BB, OS&Y, Cone Type Disc, RF
VGF-BC7
Check 15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, SW VCS-CF6
80 ~ 200 CL 300 ASTM A351 CF3M Body, SS 316L Trim, BC, Swing Type, RF VCF-BC7
Ball 15 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, RTFE Seat, Side entry with 75mm S/40S Nipples , Floating Ball, Full Port, SW
VBS-CF6
80 ~ 200 CL 300 ASTM A351 CF3M Body, SS316L Trim, RTFE seat, Side entry, Floating Ball, Full Port, RF
VBF-BC7
Butterfly 80 ~ 200 CL 300 ASTM A351 CF3M Body, SS316L Trim, Design API 609 Cat B, RTFE Seat, Wafer Lug Type
VFW-BC7
Stop Check 25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Y-Type, SW
VTS-CF6
Note :
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
102/174
PIPING MATERIAL CLASS
BC2
Rating ASME Class 300
Material Stainless Steel (316)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
CPP condensate outlet 41.0 + FV 85 Resin transfer HP 41.0 + FV 85
Resin transfer water HP 41.0 + FV 85
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.2 Class 300)
Temp (℃) 38 50 100
Press (Barg) 49.6 48.1 42.2
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316
SMLS, PE
ASME B36.19
3
20 S/40S 2.87 3
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
SMLS, BE
80 S/40S 5.49
100 S/40S 6.02
150 S/40S 7.11
200 S/40S 8.18
250 S/40S 9.27
Welded, BE
300 S/40S 9.53
350 - 11.13
500 - 15.09
550 - 17.48
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F316 Forged End, SW ASME B16.11 3
65 ~ 550 ASTM A403 WP316 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A182 F316 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F316 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F316 Forged End, SW -
Flange, Gasket & Bolt / Nut
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
103/174
PIPING MATERIAL CLASS
BC2
Rating ASME Class 300
Material Stainless Steel (316)
Code ASME B31.1
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 300
ASTM A182 F316 SW RF
ASME B16.5 3
65 ~ 250 CL 300 WN RF
Gasket All CL 300
316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF ASME B16.20/B16.21
All CL 300 Klingersil C4430 3mm T Synthetic fiber / NBR 4
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Ball 15 ~ 50 CL 600
ASTM A182 F316 Body, SS 316 Trim, BB, RTFE Seat, Side entry with 75mm S/40S Nipples , Floating Ball, Full Port, SW
VBS-CF7
80 ~ 150 CL 300 ASTM A351 CF8M Body, SS 316 Trim, BB, RTFE Seat, , Side entry, Floating Ball, Full Port, RF
VBF-BC8
Butterfly 80 ~ 200 CL 300 ASTM A351 CF8M Body, ASTM CF8M Disc, lugged pattern RTFE/PTFE seat, RF
VFF-BC8
Check 100 ~ 250 CL 300 ASTM A351 CF8M Body, SS 316 Trim, BC, Swing type, RF VCF-BC8
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Special considerations for resin transfer duty:
Elbows to be 1.5D radius
Tees to have 1.5D radius branch set
No internal protrusions
Minimize direction changes
Gaskets to be flush within bore of pipe
3. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
4. The gasket type can be used for condensate polishing plant (vendor package).
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
104/174
PIPING MATERIAL CLASS
BC3
Rating ASME Class 300
Material Stainless Steel (316L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Sealing Oil (Steam Turbine) 16.0 100
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 300)
Temp (℃) 50 100 150
Press (Barg) 40.0 34.8 31.4
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/40S 3.38
ASTM A312 TP316L SMLS, BE
ASME B36.19
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
80 S/40S 5.49
100 S/40S 6.02
150 S/40S 7.11
200 S/40S 8.18
400 S/40S 9.53 Welded. BE
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25~ 200 ASTM A403 WP316L SMLS, BW ASME B16.9
Schedule Match Pipe 1,2
250 ~ 400 ASTM A403 WP316L Welded, BW ASME B16.9
Schedule Match Pipe 1
Plug/Threadolet ~50 CL.3000 ASTM A182 F304L Forged End, TE ASME B16.11/ MSS SP-97
3
Weldolet - ASTM A182 F316L Forged End, BW MSS SP- 97
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 400 CL 300 ASTM A182 F316L WN RF ASME B16.5
Gasket All CL 300 316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF, ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
105/174
PIPING MATERIAL CLASS
BC3
Rating ASME Class 300
Material Stainless Steel (316L)
Code ASME B31.1
Note :
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. For size up to DN50, 5D bend instead of elbow can be used if the piping route is allowed. The bend thinning allowance for 5 pipe diameters is reflected into pipe wall thickness.
3. Thread connections allows the downstream of vents, drains, hydrostatic test connections, instrument take off and to match equipment.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
106/174
PIPING MATERIAL CLASS
CA1
Rating ASME Class 600
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HP Heater #7 Cascade Drain 64.0+FV 285 BFW Booster Pump Discharge 39.0 200
Cold Reheat Steam 64.0+FV 399 Fuel Additive 65.0 150
Cold Reheat Steam Drain 64.0+FV 399
Shoot Blowing Steam(After CV) 40.0 396
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/B16.47 - Group 1.1 Class 600)
Temp (℃) 150 200 250 300 325 350 375 400
Press (Barg) 90.2 87.6 83.9 79.6 77.4 75.1 72.7 69.4
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/XS 7.01
SMLS, BE
80 S/XS 7.62
100 S/XS 8.56
150 S/XS 10.97
200 S/XS 12.70
250 S/80 15.09
300 S/80 17.48
350 S/80 19.05
400 S/80 21.44
450 S/80 23.83
500 S/80 26.19
550 S/80 28.58
600 S/80 30.96
650 - 30.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 650 ASTM A234WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
107/174
PIPING MATERIAL CLASS
CA1
Rating ASME Class 600
Material Carbon Steel
Code ASME B31.1
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 600 ASTM A105 SW RF ASME B16.5
65 ~ 600 CL 600 ASTM A105
WN RF ASME B16.5
650 CL 600 WN RF ASME B16.47 Ser. A
Gasket
25 ~ 600 CL 600 316 SS Strip with
Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
650 CL 600 316 SS Strip with
Graphite filler
Spiral Wound, CS Inner/Outer
Ring 4.5mmT, RF
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 600
ASTM A105 Body, 13Cr Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF1
80 ~ 650 CL 600 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-CC2
Globe
25 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SWxNPT
VGZ-CF1 2
25 ~ 50 CL 600 ASTM A105 Body, 13CR Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF1
80 ~ 650 CL 600 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-CC2
Check 25 ~ 50 CL 600 ASTM A105 Body, 13Cr Trim, BC, Lift Type, SW VCS-CF1
80 ~ 600 CL 600 ASTM A216 WCB Body, 13Cr Trim, PSC, Swing Type, BW VCB-CC2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The end type valve (SWxNPT) shall be used for instrument root valve.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
108/174
PIPING MATERIAL CLASS
CA2
Rating ASME Class 600
Material Carbon Steel (GALV)
Code ASME B31.1 / NFPA
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Gas Fire Extinguishing System 30.0 60
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 600)
Temp (℃) 50 100 150 200 250 300
Press (Barg) 100.2 93.2 90.2 87.6 83.9 79.6
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/80 3.73
ASTM A106 Gr.B Galv.
SMLS, TE
ASME B36.10
20 S/80 3.91
25 S/80 4.55
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, PE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
250 S/STD 9.27
300 S/STD 9.53
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A105 GALV Forged End, TE ASME B16.11
65 ~ 300 ASTM A234WPB GALV SMLS, Grooved ASME B16.9 Schedule Match Pipe
1
Plate A515 Gr.60, GALV.
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 600
ASTM A105, GALV. TERF,
ASME B16.5
65 ~ 300 CL 600 WNRF
Gasket All CL 600 316 SS Strip with
Graphite filler
Spiral Wound, CS Outer Ring
4.5mmT, RF, ASME B16.20
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
109/174
PIPING MATERIAL CLASS
CA2
Rating ASME Class 600
Material Carbon Steel (GALV)
Code ASME B31.1 / NFPA
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. All equipment, valves and etc shall be UL listed or FM approved.
3. All galvanized piping shall be galvanized both internally and externally in accordance with BS EN ISO 1461 or equivalent standard
4. These valve types will be selected and provided by fire fighting supplier.
5. The screwed joint will be connected as seal-weld to prevent from service leakage, if required.
6. Final color for all pipes and fittings shall be red color (RAL 3000).
7. DN50 Grooved joint for reducing line can be used. 8. Welding joint will be applied to firefighting supplier's scope.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
110/174
PIPING MATERIAL CLASS
CB1
Rating ASME Class 600
Material Low Alloy Steel (P11)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HRS Drain (After Drain Block Valve) 64.0 440 Aux Steam Let Down Valve Spray Water Inlet 39.0+FV 450
Cold Reheat Steam (HP Exhaust Steam to NRV) 40.0+FV 64.0+FV
460 399
The pipe wall thickness is calculated based on the following design condition.
- DN25 ~ DN350 : 64.0 Barg & 440 ℃ (For HRS Drain)
- DN25~DN650: 64.0 Barg & 399 ℃ or 40.0 Barg & 460 ℃whichever is severer condition (Cold Reheat Steam for HP Exhaust Steam to NRV)
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/ B16.5 - Group 1.9 Class 600)
Temp (℃) 400 425 450 475 500 538
Press (Barg) 73.3 70.0 67.7 63.4 51.5 29.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr.P11
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/80 7.01
SMLS, BE
80 S/80 7.62
100 S/80 8.56
150 S/80 10.97
200 S/60 10.31
250 S/60 12.70
300 S/60 14.27
350 S/60 15.09
400 S/60 16.66
450 S/60 19.05
500 S/60 20.62
550 S/60 22.23
600 S/60 24.61
650 - 26.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
111/174
PIPING MATERIAL CLASS
CB1
Rating ASME Class 600
Material Low Alloy Steel (P11)
Code ASME B31.1
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW ASME B16.11
65 ~ 650 ASTM A234 WP11 CL.2 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F11 CL.2 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Plate A387 Gr.11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 600 ASTM A182 F11 CL.2 SW RF ASME B16.5 3
65 ~ 600 CL 600 ASTM A182 F11 CL.2 WN RF ASME B16.5 3
Gasket 25 ~ 600 CL 600 316 Strip with Graphite & MICA
Spiral Wound, SS Outer Ring 4.5mmT, RF
ASME B16.20
Bolt / Nut 25 ~ 600 A193-B16/ A194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25~ 50 CL 600
ASTM A182 F11 CL.2 Body, F11 Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF3 3
80 ~ 650 CL 600 ASTM A217 WC6 Body, F11 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-CC5 3,4
Globe 25~ 50 CL 600
ASTM A182 F11 CL.2 Body, F11 Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF3 3
80 ~ 300 CL 600 ASTM A217 WC6 Body, F11 Trim, PSB, OS&Y, Cone type Disc, BW
VGB-CC5 3,4
Check 25~ 50 CL 600 ASTM A182 F11 CL.2 Body, F11 Trim, BC, Lift Type, SW VCS-CF3 3
80 ~ 650 CL 600 ASTM A217 WC6 Body, F11 Trim, PSC, Swing Type, BW VCB-CC5 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
112/174
PIPING MATERIAL CLASS
CB2
Rating ASME Class 600
Material Low Alloy Steel (P91)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
LP By-Pass Spray Water Inlet 39.0+FV 550 LP By-Pass Valve Outlet 14.0+FV 550
The pipe wall thickness is calculated based on the follow design condition
- DN25 ~ DN200: 39.0 Barg +FV& 550 ℃
- DN1300: 14.0+FV Barg & 550 ℃(For LP By-pass Valve Outlet)
Pipe wall thickness under external pressure is verified. For pipe DN 1300, the stiffness ring is requested. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.15 Class 600)
Temp (℃) 500 538 550
Press (Barg) 56.5 50.0 49.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr.P91
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/STD 6.02
150 S/STD 7.11
200 S/STD 8.18
1300 - 15.0 ASTM A691 P91 CL42 WELDED, BE 1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F91 Forged End, SW ASME B16.11
65 ~ 200 ASTM A234 WP91 SMLS, BW ASME B16.9 Schedule Match Pipe
2
1300 ASTM A234 WP91 WELDED, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F91 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F91 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F91 Forged End, SW -
Plate A387 Gr.91
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
113/174
PIPING MATERIAL CLASS
CB2
Rating ASME Class 600
Material Low Alloy Steel (P91)
Code ASME B31.1
Flange 25 ~ 50 CL 600 ASTM A182 F91 SW RF ASME B16.5
Flange 65 ~ 200 CL 600 ASTM A182 F91 WN RF ASME B16.5
Gasket 25 ~ 200 CL 600 316 Strip with Graphite & MICA
Spiral Wound, SS Outer Ring 4.5mmT, RF
ASME B16.20
Bolt / Nut 25 ~ 200 A193-B16 / A194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25~ 50 CL 600
ASTM A182 F91 Body, F91 Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF9
80 ~ 200 CL 600 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-CC9 3,4
Globe 25~ 50 CL 600
ASTM A182 F91 Body, F91 Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF9
80 ~ 200 CL 600 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Cone type Disc, BW
VGB-CC9 3
Check 25~ 50 CL 600 ASTM A182 F91 Body, F91 Trim, BC, Lift Type, SW VCS-CF9
80 ~ 200 CL 600 ASTM A217 C12A Body, F91 Trim, PSC, Swing Type, BW VCB-CC9 3
Note:
1. For longitudinal weld joint, 100% radiography shall be applied in accordance with Para 136.4.5 or 100% ultrasonic examination shall be applied in accordance with 136.4.6 of ASME B31.1.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
4. The suffix ‘-W’ shall be added to valve material code when water seal is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
114/174
PIPING MATERIAL CLASS
CC1
Rating ASME Class 600
Material Stainless Steel (316L)
Code ASME B31.1 / ASME B31.3
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Chemical Dosing (Oxygen Dosing, to CPP outlet) 50.0 60 Condensate Sampling 39.0+FV 200
Chemical Dosing (Ammonia) 50.0 85
Chemical dosing piping service shall be applied in accordance with ASME B31.3. The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.3 Class 600)
Temp (℃) 50 100 150 200 250 300
Press (Barg) 80.0 69.6 62.8 58.3 54.9 52.1
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316L SMLS, PE ASME B36.19
2
20 S/40S 2.87 2
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW ASME B16.11
Sockolet 25 ~ 50 CL.3000 ASTM A182 F316L Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F316L Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F316L Forged End, SW -
Plate A240 Gr.316L
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 600 ASTM A182 F316L SW RF ASME B16.5 2
Gasket All CL 600
316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt / Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
115/174
PIPING MATERIAL CLASS
CC1
Rating ASME Class 600
Material Stainless Steel (316L)
Code ASME B31.1 / ASME B31.3
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF6
Globe 15 ~ 50 CL 600
ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF6
25 CL 600 ASTM A182 F316L Body, SS 316L Trim, BB, OS&Y, Plug Type Disc, NPT
VGT-CF6
Check 15 ~ 50 CL 600 ASTM A182 F316L Body, SS 316L Trim, BC, Lift Type, SW VCS-CF6
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
116/174
PIPING MATERIAL CLASS
CC2
Rating ASME Class 600
Material Super Duplex
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Sea water & HP RO Brine Line 65.8 50
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.8 Class 600)
Temp (℃) 38 50 100
Press (Barg) 103.4 103.4 101.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A790 S32750
SMLS, PE
ASME B36.19
2
20 S/40S 2.87 2
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
65 S/40S 5.16
SMLS, BE
80 S/40S 5.49
100 S/40S 6.02
150 S40S 7.11
200 S/40S 8.18
250 S/40S 9.27
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F53 Forged End, SW ASME B16.11 2
65 ~ 250 ASTM A815 WPS32750 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 15 ~ 50 CL.3000 ASTM A182 F53 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F53 Forged End, BW MSS SP- 97
Boss 15~ 50 CL.3000 ASTM A182 F53 Forged End, SW -
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 600
ASTM A182 F53 SW RF
ASME B16.5 2
65 ~ 250 CL 600 WN RF
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
117/174
PIPING MATERIAL CLASS
CC2
Rating ASME Class 600
Material Super Duplex
Code ASME B31.1
Gasket All CL 600 Inconel 625 winding with
Graphite filler
Spiral Wound, SS Outer
Ring 4.5mmT, RF ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 8M
Stud Bolt / Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate
15 ~ 50 CL 600 ASTM A182 F53 Body, UNS S32750 Trim, BB, OS&Y, Solid Wedge Disc, SW
VAS-CF11
15 ~ 50 CL 600 ASTM A182 F53 Body, UNS S32750 Trim, BB, OS&Y, Solid Wedge Disc, NPT
VAT-CF11
80 ~ 250 CL 600 ASTM A995 Gr. 5A Body, UNS S32750 Trim, BB, OS&Y, Flexible Wedge Disc, RF
VAF-CC13
Globe 15 ~ 50 CL 600
ASTM A182 F53 Body, UNS S32750 Trim, BB, OS&Y, Plug Type Disc, SW
VGS-CF11
80 ~ 250 CL 600 ASTM A995 Gr. 5A Body, UNS S32750 Trim, BB, OS&Y, Cone Disc, RF
VGF-CC13
Check 15 ~ 50 CL 600
ASTM A182 F53 Body, UNS S32750 Trim, BC, Lift Type, SW
VCS-CF11
80 ~ 250 CL 600 ASTM A995 Gr. 5A Body, UNS S32750 Trim, BC, Swing Type, RF
VCF-CC13
Ball 15 ~ 50 CL 600 ASTM A182 F53Body, UNS S32750 Trim, RTFE Seat, Side Entry, Floating Ball, SW
VBS-CF11
Butterfly 80 ~ 250 CL 600 ASTM A995 Gr. 5A Body, UNS S32750 Trim, Design API 609 Cat B, RTFE Seat, Wafer lug
VFW-CC13
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
118/174
PIPING MATERIAL CLASS
CC3
Rating ASME Class 600
Material Stainless Steel (304L)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Control Oil (Steam Turbine) 55.0 80
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Flanges (Based on ASME B16.5 - Group 2.3 Class 600)
Temp (℃) 50 100 150
Press (Barg) 80.0 69.6 62.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP304L SMLS, PE ASME B36.19
20 S/40S 2.87
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
~ 50 - ASTM 403 WP304L SMLS, BW ASME B16.9 Schedule Match Pipe
1
Plug/Threadolet ~50 CL.3000 ASTM A182 F304L Forged End, TE ASME B16.11/ MSS SP-97
2
Weldolet ~ 50 ASTM A182 F304L Forged End, BW MSS SP- 97
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange ~ 50 CL 600 ASTM A182 F304L WN RF ASME B16.5
Gasket All CL 600 316 SS Strip with
Graphite filler
Spiral Wound, SS Outer Ring
4.5mmT, RF ASME B16.20
Bolt / Nut All A193 B8 CL.2 /A194 8
Stud Bolt / Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Note:
1. 5D bend instead of elbow can be used if the piping route is allowed. The bend thinning allowance for 5 pipe diameters is reflected into pipe wall thickness.
2. Thread connections allows the downstream of vents, drains, hydrostatic test connections, instrument take off and to match equipment.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
119/174
PIPING MATERIAL CLASS
CC4
Rating ASME Class 600
Material 316SS Tubing
Code ASME B31.3
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Lubricating and Control Oil (Steam Turbine) 55.0 80
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Tube
Item Size (OD) SCH. THK (mm)
Material Description Note
Tube
OD 18 - 2.0
316Ti (X6CrNiMoTi17-12-2/ 1.4571)
SMLS, PE
OD 22 - 2.0
OD 28 - 2.0
OD 35 - 2.0
OD 42 - 2.0
Tube Fittings
Item Size (OD) Rating Material Description Dimension Note
Elbow, Nipple, Union, Tee, Connector
OD 18 ~OD 42
316Ti (X6CrNiMoTi17-12-2/ 1.4571)
Butt Welded or Thread O-ring (Viton)
Manufacture Std.
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Valves
Item Size (DN) Rating Description Material Code Note
Note:
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
120/174
PIPING MATERIAL CLASS
DA1
Rating ASME Class 900
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HP Heater #8 Cascade Drain 112.0+FV 330
Boiler High Pressure Drain Header 110 340
The pipe wall thickness is calculated with the highest condition among above. Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 900)
Temp (℃) 100 150 200 250 300 325 350
Press (Barg) 139.8 135.2 131.4 125.8 119.5 116.1 112.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/XS 7.01
SMLS, BE
80 S/XS 7.62
100 S/XS 8.56
150 S/XS 10.97
200 S/100 15.09
250 S/100 18.26
300 S/100 21.44
350 S/100 23.83
400 S/100 26.19
450 S/100 29.36
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A105 Forged End, SW ASME B16.11 2
65 ~ 450 ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A105 Forged End, SW -
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
121/174
PIPING MATERIAL CLASS
DA1
Rating ASME Class 900
Material Carbon Steel
Code ASME B31.1
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 1500
ASTM A105 SW RTJ
ASME B16.5
65 ~ 450 CL 900 WNRTJ
Gasket 25 ~ 50 CL 1500
Soft Iron (Cadmium Coating,)
Octagonal Ring type ASME B16.20
65 ~ 450 CL 900 Soft Iron (Cadmium Coating,)
Octagonal Ring type
Bolt / Nut All A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25~ 50 CL 1500 ASTM A105 Body, 13Cr Trim, WB, OS&Y, Solid Wedge
Disc, SW VAS-EF1
80 ~ 450 CL 900 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-DC2
Globe 25~ 50 CL 1500 ASTM A105 Body, 13CR Trim, Bonnetless or WB, OS&Y,
Plug Type Disc, SW VGS-EF1
80 ~ 400 CL 900 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-DC2
Check 25~ 50 CL 1500 ASTM A105 Body, 13Cr Trim, WC, Lift Type, SW VCS-EF1
80 ~ 450 CL 900 ASTM A216 WCB Body, 13Cr Trim, PSC, Tilting Type, BW VCB-DC2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
122/174
PIPING MATERIAL CLASS
DB1
Rating ASME Class 900
Material Low Alloy Steel (P11)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
RH Desuperheater Out Vent 64.0 510 ERV Vent 40 420
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.9 Class 900)
Temp (℃) 400 425 450 475 500 538 550
Press (Barg) 109.8 105.1 101.4 95.1 77.2 44.7 38.1
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr. P11
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
80 S/XS 7.62 SMLS, BE
100 S/XS 8.56
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW ASME B16.11 3
65 ~ 100 ASTM A234 WP11 CL.2 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW MSS SP- 97 3
Weldolet 65 ~ - ASTM A182 F11 CL.2 Forged End, BW MSS SP- 97 3
Boss 25~ 50 CL.3000 ASTM A182 F11 CL.2 Forged End, SW - 3
Plate A387 Gr.11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 1500 ASTM A182 F11 CL.2 SW RTJ ASME B16.5 3
80 ~ 100 CL 900 ASTM A182 F11 CL.2 WNRTJ ASME B16.5 3
Gasket 25 ~ 50 CL 1500 1 1/4Cr-1/2 Mo Octagonal Ring type ASME B16.20
80 ~ 100 CL 900 1 1/4Cr-1/2 Mo Octagonal Ring type ASME B16.20
Bolt / Nut All A193-B16 / A194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 1500 ASTM A182 F11 CL.2 Body, F11 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF3 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
123/174
PIPING MATERIAL CLASS
DB1
Rating ASME Class 900
Material Low Alloy Steel (P11)
Code ASME B31.1
Globe 25 ~ 50 CL 1500 ASTM A182 F11 CL.2 Body, F11 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-EF3 3
Check 25 ~ 50 CL 1500 ASTM A182 F11 CL.2 Body, F11 Trim, WC, Lift Type, SW VCS-EF3 3
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
124/174
PIPING MATERIAL CLASS
DB1S
Rating ASME Class 900
Material Low Alloy Steel (P11)
Code ASME SEC. I
(Boiler External Piping)
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
RH Desuperheater Out Vent 64.0 510
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.9 Class 900)
Temp (℃) 400 425 450 475 500 538 550
Press (Barg) 109.8 105.1 101.4 95.1 77.2 44.7 38.1
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASME SA335 Gr. P11 SMLS, PE ASME B36.10
40 S/80 5.08
50 S/80 5.54
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL.3000 ASME SA182 F11 CL.2 Forged End, SW ASME B16.11 3
Sockolet 25 ~ 50 CL.3000 ASME SA182 F11 CL.2 Forged End, SW MSS SP- 97 3
Boss 25 ~ 50 CL.3000 ASME SA182 F11 CL.2 Forged End, SW - 3
Plate SA387 Gr.11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 SW RTJ ASME B16.5 3
Gasket 25 ~ 50 CL 1500 1 1/4Cr-1/2 Mo Octagonal Ring type ASME B16.20
Bolt / Nut All SA193-B16 / SA194-3 Stud Bolt / Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF3-S 3
Globe 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-EF3-S 3
Check 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, WC, Lift Type, SW VCS-EF3-S 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
125/174
PIPING MATERIAL CLASS
DB1S
Rating ASME Class 900
Material Low Alloy Steel (P11)
Code ASME SEC. I
(Boiler External Piping)
Note:
1. The carbon content of material in this class shall not exceed 0.15%. 2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
126/174
PIPING MATERIAL CLASS
DB2
Rating ASME Class 900
Material Low Alloy Steel (P91)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Hot Reheat Steam 64.0 550
The pipe wall thickness is calculated with the highest condition among above. 5D bend thinning allowance is applied to all pipe wall thicknesses in this class. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5/B16.47 - Group 1.15 Class 900)
Temp (℃) 450 475 500 538 550 575
Press (Barg) 101.4 95.1 84.7 75.2 74.8 71.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/80 4.55
ASTM A335 Gr.P91
SMLS, PE
ASME B36.10
40 S/80 5.08
50 S/80 5.54
65 S/STD 5.16
SMLS, BE
80 S/STD 5.49
100 S/XS 8.56
150 S/XS 10.97
200 ~ 250 S/XS 12.70
300 S/60 14.27
350 S/80 19.05
400 S/80 21.44
450 S/80 23.83
500 S/80 26.19
550 S/80 28.58
600 S/60 24.61
650 - 27.00
700 - 29.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL.3000 ASTM A182 F91 Forged End, SW ASME B16.11
65 ~ 700 ASTM A234 WP91 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.3000 ASTM A182 F91 Forged End, SW MSS SP- 97
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
127/174
PIPING MATERIAL CLASS
DB2
Rating ASME Class 900
Material Low Alloy Steel (P91)
Code ASME B31.1
Weldolet 65 ~ - ASTM A182 F91 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.3000 ASTM A182 F91 Forged End, SW -
Plate A387 Gr.91
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange
25 ~ 50 CL 1500
ASTM A182 F91
SWRTJ ASME B16.5
65 ~ 600 CL 900 WNRTJ
650 ~ 700 CL 900 WNRTJ ASME B16.47 Ser.A
Gasket 25 ~ 50 CL 1500 9Cr-1Mo Octagonal Ring type
ASME B16.20
65 ~ 700 CL 900 9Cr-1Mo Octagonal Ring type
Bolt / Nut All A193-B16 / A194-3 Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 1500 ASTM A182 F91 Body, F91 Trim, WB, OS&Y, Solid Wedge
Disc, SW VAS-EF9
80 ~ 700 CL 900 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-DC9 2
Globe 25 ~ 50 CL 1500 ASTM A182 F91 Body, F91 Trim, Bonnetless or WB, OS&Y,
Plug Type Disc, SW VGS-EF9
80 ~ 400 CL 900 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-DC9 2
Check 25 ~ 50 CL 1500 ASTM A182 F91 Body, F91 Trim, WC, Lift Type, SW VCS-EF9
80 ~ 600 CL 900 ASTM A217 C12A Body, F91 Trim, PSC, Tilting Type, BW VCB-DC9 2
Angle 80 ~ 600 CL 900 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Angle Type, BW
VLB-DC9 2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
128/174
PIPING MATERIAL CLASS
DC1
Rating ASME Class 900
Material Stainless Steel (316)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Hot Reheat Steam Sampling 64.0 550
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Valves and Flanges (Based on ASME B16.34/B16.5 -Group 2.2 Class 900)
Temp (℃) 500 538 550 575
Press (Barg) 84.7 75.2 74.8 71.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 S/40S 2.77
ASTM A312 TP316 SMLS, PE ASME B36.19
3
20 S/40S 2.87 3
25 S/40S 3.38
40 S/40S 3.68
50 S/40S 3.91
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 50 CL 3000 ASTM A182 F316 Forged End, SW ASME B16.11 3
Sockolet 15 ~ 50 CL.3000 ASTM A182 F316 Forged End, SW MSS SP- 97
Boss 15~ 50 CL.3000 ASTM A182 F316 Forged End, SW -
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~50 CL 1500 ASTM A182 F316 SWRTJ ASME B16.5 1
Gasket 15 ~ 50 CL 1500 SS 316 Octagonal Ring Type, ASME B16.20
Bolt / Nut All A193 B8M CL.2 /A194 -8M
Stud Bolt /Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, WB, OS&Y, Solid Wedge Disc, SW,
VAS-EF7
Globe 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-EF7
Check 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, WC, Lift Type, SW VCS-EF7
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
129/174
PIPING MATERIAL CLASS
DC1
Rating ASME Class 900
Material Stainless Steel (316)
Code ASME B31.1
Note:
1. Raised Face (RF) Flange shall be used when connecting to special equipment.
2. Schedule (thickness) shall be equal to or greater than that of pipe. 3. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
130/174
PIPING MATERIAL CLASS
EA1
Rating ASME Class 1500
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
BFWP Bleeding To Spray Water 140.0 200
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.1 Class 1500)
Temp (℃) 100 150 200 250 300 325 350
Press (Barg) 233.0 225.4 219.0 209.7 199.1 193.6 187.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/160 6.35
ASTM A106 Gr.B
SMLS, PE
ASME B36.10
40 S/160 7.14
50 S/160 8.74
65 S/160 9.53
SMLS, BE
80 S/160 11.13
100 S/120 11.13
150 S/120 14.27
200 S/120 18.26
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 6000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 200 ASTM A234 WPB SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL 6000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL 6000 ASTM A105 Forged End, SW -
Plate A515 Gr.60
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 1500
ASTM A105 SWRTJ
ASME B16.5
65 ~ 200 CL 1500 WNRTJ
Gasket 25 ~ 200 CL 1500 Soft Iron (Cadmium Coating,)
Octagonal Ring type ASME B16.20
Bolt / Nut ALL A193-B7 / A194-2H Stud bolt / Heavy Hex nuts with Hot-Dip Galvanized
ASME B1.1 /ASME B18.2.2
Valves
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
131/174
PIPING MATERIAL CLASS
EA1
Rating ASME Class 1500
Material Carbon Steel
Code ASME B31.1
Item Size (DN) Rating Description Material Code Note
Gate 25~ 50 CL 1500 ASTM A105 Body, 13Cr Trim, WB, OS&Y, Solid Wedge
Disc, SW VAS-EF1
80 ~ 200 CL 1500 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-EC2
Globe 25~ 50 CL 1500 ASTM A105 Body, 13CR Trim, Bonnetless or WB, OS&Y,
Plug Type Disc, SW VGS-EF1
80 ~ 200 CL 1500 ASTM A216 WCB Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-EC2
Check 25~ 50 CL 1500 ASTM A105 Body, 13Cr Trim, WC, Lift Type, SW VCS-EF1
80 ~ 200 CL 1500 ASTM A216 WCB Body, 13Cr Trim, PSC, Tilting Type, BW VCB-EC2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
132/174
PIPING MATERIAL CLASS
EB1
Rating ASME Class 1500
Material Low Alloy Steel (P11)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HP Extraction Steam to HP Heater #8 112.0+FV 420
Pipe wall thickness under external pressure is verified. The selected pipe thickness is satisfied and stiffening ring is not required. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.9 Class 1500)
Temp (℃) 400 425 450 475 500 538
Press (Barg) 183.1 175.1 169.0 158.2 128.6 74.5
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/160 6.35
ASTM A335 P11
SMLS, PE
ASME B36.10
40 S/160 7.14
50 S/160 8.74
65 S/80 7.01
SMLS, BE
80 S/80 7.62
100 S/120 11.13
150 S/120 14.27
200 S/120 18.26
250 S/120 21.44
300 S/120 25.40
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 6000 ASTM A182 F11 CL.2 Forged End, SW ASME B16.11
65 ~ 300 ASTM A234 WP11 CL.2 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.6000 ASTM A182 F11 CL.2 Forged End, SW MSS SP- 97 3
Weldolet 65 ~ - ASTM A182 F11 CL.2 Forged End, BW MSS SP- 97 3
Boss 25~ 50 CL.6000 ASTM A182 F11 CL.2 Forged End, SW - 3
Plate A387 Gr.11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL1500 ASTM A182 F11 CL.2 SWRTJ ASME B16.5 3
65 ~ 300 CL1500 ASTM A182 F11 CL.2 WNRTJ ASME B16.5 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
133/174
PIPING MATERIAL CLASS
EB1
Rating ASME Class 1500
Material Low Alloy Steel (P11)
Code ASME B31.1
Gasket 25 ~ 300 CL1500 1 1/4Cr-1/2 Mo Octagonal ring type ASME B16.20
Bolt / Nut ALL A193-B16/ A194-3 Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL1500
ASTM A182 F11 CL.2 Body, F11 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF3 3
80 ~ 300 CL1500 ASTM A217 WC6 Body, F11 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-EC5 3,4
Globe 25 ~ 50 CL1500 ASTM A182 F11 CL.2 Body, F11 Trim, Bonnetless or WB,
OS&Y, Plug Type disc, SW VGS-EF3 3
80 ~ 300 CL1500 ASTM A217 WC6 Body, F11 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-EC5 3,4
Check 25 ~ 50 CL1500 ASTM A182 F11 CL.2 Body, F11 Trim, WC, Lift Type, SW VCS-EF3 3
80 ~ 300 CL1500 ASTM A217 WC6 Body, F11 Trim, PSC, Tilting Type, BW VCB-EC5 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
134/174
PIPING MATERIAL CLASS
EB1S
Rating ASME Class 1500
Material Low Alloy Steel (P11)
Code ASME SEC. I
(Boiler External Piping)
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
RH Desuperheater From BFWP 92.0 510
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.9 Class 1500)
Temp (℃) 450 475 500 538
Press (Barg) 169.0 158.2 128.6 74.5
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/160 6.35
ASME SA335 P11
SMLS, PE
ASME B36.10
40 S/160 7.14
50 S/160 8.74
65 S/160 9.53
SMLS, BE
80 S/160 11.13
100 S/160 13.49
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 6000 ASME SA182 F11 CL.2 Forged End, SW ASME B16.11
65 ~ 100 - ASME SA234 WP11 CL.2 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.6000 ASME SA182 F11 CL.2 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASME SA182 F11 CL.2 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.6000 ASME SA182 F11 CL.2 Forged End, SW -
Plate SA387 Gr.11
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 SW RTJ ASME B16.5 3
65 ~ 100 CL 1500 ASME SA182 F11 CL.2 WNRTJ ASME B16.5 3
Gasket 25 ~ 100 CL 1500 1 1/4Cr-1/2 Mo Octagonal ring type ASME B16.20
Bolt / Nut ALL SA193-B16/ SA194-3 Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF3-S 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
135/174
PIPING MATERIAL CLASS
EB1S
Rating ASME Class 1500
Material Low Alloy Steel (P11)
Code ASME SEC. I
(Boiler External Piping)
80 ~ 100 CL 1500 ASME SA217 WC6 Body, F11 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-EC5-S 3,4
Globe 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, Bonnetless or WB,
OS&Y, Plug Type disc, SW VGS-EF3-S 3
80 ~ 100 CL 1500 ASME SA217 WC6 Body, F11 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-EC5-S 3,4
Check 25 ~ 50 CL 1500 ASME SA182 F11 CL.2 Body, F11 Trim, WC, Lift Type, SW VCS-EF3-S 3
80 ~ 100 CL 1500 ASME SA217 WC6 Body, F11 Trim, PSC, Tilting Type, BW VCB-EC5-S 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only.
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
136/174
PIPING MATERIAL CLASS
EB2
Rating ASME Class 1500
Material Low Alloy Steel (P91)
Code ASME B31.1
Service D.P.
(Barg)D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HP By-Pass Spray Water Inlet (After Stop Check Valve) 120.0 550
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 1.15 Class 1500)
Temp (℃) 500 538 550 575
Press (Barg) 140.9 125.5 124.9 119.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/160 6.35
ASTM A335 P91
SMLS, PE
ASME B36.10
40 S/160 7.14
50 S/160 8.74
65 S/XS 7.01
SMLS, BE
80 S/XS 7.62
100 S/120 11.13
150 S/120 14.27
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 6000 ASTM A182 F91 Forged End, SW ASME B16.11
65 ~ 150 ASTM A234 WP91 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.6000 ASTM A182 F91 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F91 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.6000 ASTM A182 F91 Forged End, SW -
Plate A387 Gr.91
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 25 ~ 50 CL1500 ASTM A182 F91 SWRTJ ASME B16.5
65 ~ 150 CL1500 ASTM A182 F91 WNRTJ ASME B16.5
Gasket 25 ~ 150 CL1500 9Cr-1Mo Octagonal Ring type ASME B16.20
Bolt / Nut ALL A193-B16 / A194-3 Stud Bolt /Heavy Hex Nuts with Aluminum Ceramic Coating
ASME B1.1 /ASME B18.2.2
Valves
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
137/174
PIPING MATERIAL CLASS
EB2
Rating ASME Class 1500
Material Low Alloy Steel (P91)
Code ASME B31.1
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL1500
ASTM A182 F91, Body, F91 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF9
80 ~ 150 CL1500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-EC9 2,3
Globe 25 ~ 50 CL1500 ASTM A182 F91 Body, F91 Trim, Bonnetless or WB, OS&Y,
Plug Type Disc, SW VGS-EF9
80 ~ 150 CL1500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-EC9 2,3
Stop Check 150 CL1500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Y-Type, BW VTB-EC9 2,3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Use normalized and tempered material only.
3. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
138/174
PIPING MATERIAL CLASS
EC1
Rating ASME Class 1500
Material Stainless Steel (316)
Code ASME B31.1
Service D.P.
(Barg)D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
High Pressure Boiler Wash Water 200.0 50 Sampling (HP Feedwater Heater No.6,7,8 Drain) 110+FV 330
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves and Flanges (Based on ASME B16.34/B16.5 - Group 2.2 Class 1500)
Temp (℃) 50 100 150 200 250 300 350
Press (Barg) 240.6 211.0 192.5 178.3 166.9 158.1 151.6
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
10 S/80S 3.20
ASTM A312 TP316 SMLS, PE ASME B36.19
3
15 S/80S 3.73 3
20 S/80S 3.91 3
25 S/80S 4.55
40 S/80S 5.08
50 S/80S 5.54
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
10 ~ 50 CL 6000 ASTM A182 F316 Forged End, SW ASME B16.11 3
Sockolet 10 ~ 50 CL.6000 ASTM A105 Forged End, SW MSS SP- 97
Boss 10~ 50 CL.6000 ASTM A105 Forged End, SW -
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Flange 15 ~ 50 CL 1500 ASTM A182 F316 SWRTJ ASME B16.5 1,3
Gasket 15 ~ 50 CL 1500 SS 316 Octagonal Ring Type ASME B16.20 3
Bolt / Nut All A193 B8M CL.2 /A194 -8M
Stud Bolt / Heavy Hex Nuts ASME B1.1 /ASME B18.2.2
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-EF7 3
Globe 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-EF7 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
139/174
PIPING MATERIAL CLASS
EC1
Rating ASME Class 1500
Material Stainless Steel (316)
Code ASME B31.1
Check 15 ~ 50 CL 1500 ASTM A182 F316 Body, SS 316 Trim, WC, Lift Type, SW VCS-EF7 3
Note:
1. Raised Face(RF) Flange shall be used when connecting to special equipment
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
140/174
PIPING MATERIAL CLASS
FA1
Rating ASME Special Class 2500
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
BFW Pump Discharge (from MOV) 340.0 350 1&2RY Desuperheater Drain 331.0 376
Economizer Outlet Header To 1&2RY Desuperheater SH Spray Vent
331.0 376
From BCP Purge Water Cooler to BCP 331.0 350
The pipe wall thickness is calculated based on following design condition.
- DN25 ~ DN400 : 332.0 Barg & 376 ℃
- ID300, ID450 & ID520 (ID Control & BFW Pump Discharge only) : 340.0 Barg & 350 ℃ Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits
For Forging Valves (Based on ASME B16.34 - Group 1.1 Special Class 2500)
Temp (℃) 200 250 300 325 350 375 400
Press (Barg) 421.4 421.1 421.1 417.6 407.6 392.5 361.7
For Casting Valves (Based on ASME B16.34 - Group 1.2 Special Class 2500)
Temp (℃) 200 250 300 325 350 375 400
Press (Barg) 430.9 430.9 430.9 430.9 425.8 403.1 361.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASTM A106 Gr.C
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 - 18.50
125 23.00
150 - 27.00
200 - 34.00
250 - 42.00
300 - 49.00
350 - 53.00
400 - 60.00
ID 200 - Min. 34.0
ID 300 - Min. 48.0
ID 350 - Min 56.0
ID 450 - Min 71.0
ID 520 - Min 81.0
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
141/174
PIPING MATERIAL CLASS
FA1
Rating ASME Special Class 2500
Material Carbon Steel
Code ASME B31.1
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASTM A105 Forged End, SW ASME B16.11
65 ~ 400 ID 300 ID 350 ID 450 ID 520
ASTM A234 WPC SMLS, BW ASME B16.9 Schedule Match Pipe 1
Sockolet 25 ~ 50 CL.9000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASTM A105 Forged End, SW -
Plate A515 Gr.70
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Valves
Item Size (DN) Rating Description Material Code Note
Gate
25 ~ 50 Special
CL 2500 ASTM A105 Body, 13Cr Trim, WB, OS&Y Solid Wedge Disc, SW
VAS-FF1
80 ~ 300 Special
CL 2500 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC3 2
ID 300 ID 450 ID 520
Special CL 2500
ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC3-1
Globe 25 ~ 50
Special CL 2500
ASTM A105 Body, 13Cr Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-FF1
80 ~ 300 Special
CL 2500 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-FC3 2
Check 25 ~ 50
Special CL 2500
ASTM A105 Body, 13Cr Trim, WC, Lift Type, SW VCS-FF1
80 ~ 300 Special
CL 2500 ASTM A216 WCC Body, 13Cr Trim, PSC, Tilting Type, BW VCB-FC3
Needle 25 ~ 50
Special CL 2500
ASTM A105 Body, 13Cr Trim, WB, OS&Y, Needle Disc, SW VNS-FF1
80 ~ 300 Special
CL 2500 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Needle Disc, BW
VNB-FC3
Stop Check 80 Special
CL 2500 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Y-type, BW
VTB-FC3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The suffix ‘-L’ shall be added to valve material code when limit switch is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
142/174
PIPING MATERIAL CLASS
FA1S
Rating ASME Special Class 2500
Material Carbon Steel
Code ASME SEC. I
(Boiler External Piping)
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg)D.T. (℃)
Eco. Outlet Header to 1&2RY Desuperheater Spray Water 331.0 376 BFW Pump Discharge (After Check Valve) 331.0 350
Boiler Recirculation Pump Outlet To Economizer
(NR valve to Feedwater) 331.0 376
Boiler Recirculation Pump Outlet To Economizer
(BCP to NR valve) 299.0 376
The pipe wall thickness is calculated based on following design condition.
- DN25 ~ DN400 : 331.0 Barg & 376 ℃
- ID520 (ID Control & BFW Pump Discharge only) : 331.0 Barg & 350 ℃ Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Forging Valves (Based on ASME B16.34 - Group 1.1 Special Class 2500)
Temp (℃) 200 250 300 325 350 375 400
Press (Barg) 421.4 421.1 421.1 417.6 407.6 392.5 361.7
For Casting Valves (Based on ASME B16.34 - Group 1.2 Special Class 2500)
Temp (℃) 200 250 300 325 350 375 400
Press (Barg) 430.9 430.9 430.9 430.9 425.8 403.1 361.7
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASME SA106 Gr.C
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 - 18.50
150 - 27.00
200 - 34.00
250 - 42.00
300 - 49.00
350 - 53.00
400 - 60.00
ID520 - Min. 81.0
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASME SA105 Forged End, SW ASME B16.11
65 ~ 400 IID 520
ASME SA234 WPC SMLS, BW ASME B16.9 Schedule Match Pipe
1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
143/174
PIPING MATERIAL CLASS
FA1S
Rating ASME Special Class 2500
Material Carbon Steel
Code ASME SEC. I
(Boiler External Piping)
Sockolet 25 ~ 50 CL.9000 ASME A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASME A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASME A105 Forged End, SW -
Plate SA515 Gr.70
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Valves
Item Size (DN) Rating Description Material Code Note
Gate
25 ~ 50 Special
CL 2500 ASME SA105 Body, 13Cr Trim, WB, OS&Y Solid Wedge Disc, SW
VAS-FF1-S
80 ~ 400 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC3-S 2
ID520 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC3-1S
Globe 25 ~ 50
Special CL 2500
ASME SA105 Body, 13Cr Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-FF1-S
80 ~ 400 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-FC3-S
Check 25 ~ 50
Special CL 2500
ASME SA105 Body, 13Cr Trim, WC, Lift Type, SW VCS-FF1-S
80 ~ 400 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSC, Tilting Type, BW VCB-FC3-S
Stop Check 80 ~ 400 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSB, OS&Y, Y-Type, BW
VTB-FC3-S
Needle 25 ~ 50
Special CL 2500
ASME SA105 Body, 13Cr Trim, WB, OS&Y, Needle Disc, SW VNS-FF1-S
80 ~ 400 Special
CL 2500 ASME SA216 WCC Body, 13Cr Trim, PSB, OS&Y, Needle Disc, BW
VNB-FC3-S
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The suffix ‘-L’ shall be added to valve material code when limit switch is applied.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
144/174
PIPING MATERIAL CLASS
FB1
Rating ASME Special Class 2500
Material Low Alloy Steel (P22)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
2RY SH Inlet Vent 292.0 454 W/S Equalizing Line Vent 297.0 457
2RY Pass Inlet Manifold Drain 311.0 450 HP Steam Drain 283.0 440
1RY SH Spray Water 292.0 465 Roof Outlet Header Drain (After Block Valve) 311 395
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves (Based on ASME B16.34 - Group 1.10. Special Class 2500)
Temp (℃) 400 425 450 475 500 538
Press (Barg) 406.3 406.3 393.1 356.3 297.5 192.1
Pipe
Item Size (DN)
SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASTM A335 Gr.P22
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 - 18.50
150 - 27.00
300 - 49.00
350 - 53.00
Fittings
Item Size (DN)
Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASTM A182 F22 CL.3 Forged End, SW ASME B16.11
65 ~ 350 ASTM A234 WP22 CL.3 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.9000 ASTM A182 F22 CL.3 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F22 CL.3 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASTM A182 F22 CL.3 Forged End, SW -
Plate A387 Gr22
Flange, Gasket & Bolt / Nut
Item Size (DN)
Rating Material Description Dimension Note
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
145/174
PIPING MATERIAL CLASS
FB1
Rating ASME Special Class 2500
Material Low Alloy Steel (P22)
Code ASME B31.1
Valves
Item Size (DN)
Rating Description Material Code Note
Gate 25 ~ 50
Special CL 2500
ASTM A182 F22 CL.3 Body, F22 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-FF4
80 ~ 150 Special
CL 2500 ASTM A217 WC9 Body, F22 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC6
Globe 25 ~ 50
Special CL 2500
ASTM A182 F22 CL.3 Body, F22 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-FF4
80 ~ 150 Special
CL 2500 ASTM A217 WC9 Body, F22 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-FC6 3.4
Check 25 ~ 50
Special CL 2500 ASTM A182 F22 CL.3 Body, F22 Trim, WC, Lift Type, SW VCS-FF4
80 ~ 150 Special
CL 2500 ASTM A217 WC9 Body, F22 Trim, PSC, Tilting Type, BW VCB-FC6 3.4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
146/174
PIPING MATERIAL CLASS
FB1S
Rating ASME Special Class 2500
Material Low Alloy Steel (P22)
Code ASME SEC. I
(Boiler External Piping)
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
2RY SH Inlet Vent 292.0 465 W/S Equalizing Line Vent 297.0 457
2RY Pass Inlet Manifold 311.0 450 PRI. Desuperheater Spray Water 292 465
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves (Based on ASME B16.34 - Group 1.10. Special Class 2500)
Temp (℃) 400 425 450 475 500 538 550
Press (Barg) 406.3 406.3 393.1 356.3 297.5 192.1 162.8
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASME SA335 Gr.P22
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 - 18.50
150 - 27.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASME SA182 F22 CL.3 Forged End, SW ASME B16.11
65 ~ 150 ASME SA234 WP22 CL.3 SMLS, BW ASME B16.9 Schedule Match Pipe
2
Sockolet 25 ~ 50 CL.9000 ASME SA182 F22 CL.3 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASME SA182 F22 CL.3 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASME SA182 F22 CL.3 Forged End, SW -
Plate ASME SA387 Gr22
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50
Special CL 2500
ASME SA182 F22 CL.3 Body, F22 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-FF4-S
80 ~ 150 Special
CL 2500 ASME SA217 WC9 Body, F22 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-FC6-S 3,4
Globe 25 ~ 50 Special
CL 2500 ASME SA182 F22 CL.3 Body, F22 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-FF4-S
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
147/174
PIPING MATERIAL CLASS
FB1S
Rating ASME Special Class 2500
Material Low Alloy Steel (P22)
Code ASME SEC. I
(Boiler External Piping)
80 ~ 150 Special
CL 2500 ASME SA217 WC9 Body, F22 Trim, PSB, OS&Y, Cone Type Disc BW
VGB-FC6-S 3,4
Check 25 ~ 50
Special CL 2500
ASME SA182 F22 CL.3 Body, F22 Trim, WC, Lift Type, SW VCS-FF4-S
80 ~ 150 Special
CL 2500 ASME SA217 WC9 Body, F22 Trim, PSC, Tilting Type, BW VCB-FC6-S 3,4
Note:
1. The carbon content of material in this class shall not exceed 0.15%.
2. Schedule (thickness) shall be equal to or greater than that of pipe.
3. Use normalized and tempered material only
4. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
148/174
PIPING MATERIAL CLASS
FC1
Rating ASME Class 2500
Material Stainless Steel (TP321)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
Lubricating Oil (Steam Turbine) 350.0 80.0
Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pipe & Tube
Item Size
(DN/OD) SCH.
THK (mm)
Material Description Dimension Note
Tube OD 16 3.0 316Ti (X6CrNiMoTi17-12-2/ 1.4571)
SMSL, PE -
Pipe
15 - 4.78
ASTM A312 TP321 SMLS, PE ASME B36.19
1
20 - 5.56 1
25 - 6.35 1
Fittings
Item Size
(DN/OD) Rating Material Description Dimension Note
Tube Fitting (Union, Nipple, Connector)
OD 16 - 316Ti (X6CrNiMoTi17-12-2/ 1.4571)
Butt Welded or Thread O-ring (Viton)
Manufacture Standard
Elbow Tee Reducer Cap
~25 - ASTM A403 WP321 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Flange, Gasket & Bolt / Nut
Item Size (DN) Rating Material Description Dimension Note
Note:
1. 5D bend instead of elbow can be used if the piping route is allowed. The bend thinning allowance for 5 pipe diameters is reflected into pipe wall thickness.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
149/174
PIPING MATERIAL CLASS
GA1
Rating ASME Class 4500
& Intermediate Class 3000
Material Carbon Steel
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
BFW Pump Discharge (to MOV) 455.0 200 BFW Pump Discharge (Min. Flow) 455.0 200
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Forging Valves (Based on ASME B16.34 - Group 1.1 Class 4500)
Temp (℃) 200 250 300
Press (Barg) 657.0 629.1 597.3
For Casting Valves (Based on ASME B16.34 - Group 1.2 Class 3000)
The pressure-temperature rating is calculated in accordance with “B-4 Intermediate Rating Class Method” of ASME 16.34 Appendix B and the minimum valve wall thickness for intermediate rating valve body shall be complied with the code.
Temp (℃) 200 250 300
Press (Barg) 486.5 463.4 428.5
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASTM A106 Gr.C
SMLS, PE
ASME B36.10
40 - 11.0 mmT
50 - 13.0 mmT
ID 150 - Min. 35.0
SMLS, BE
ID 200 - Min. 47.0
ID 350 - Min. 80.0
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASTM A105 Forged End, SW ASME B16.11
ID 200 ID 350
ASTM A234 WPC SMLS, BW ASME B16.9 Schedule Match Pipe
1
Sockolet 25 ~ 50 CL.9000 ASTM A105 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A105 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASTM A105 Forged End, SW -
Plate A515 Gr.70
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 4500 ASTM A105 Body, 13Cr Trim, WB, OS&Y, SW VAS-GF1
ID200 ID350
CL 3000 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-GC3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
150/174
PIPING MATERIAL CLASS
GA1
Rating ASME Class 4500
& Intermediate Class 3000
Material Carbon Steel
Code ASME B31.1
Globe 25 ~ 50 CL 4500 ASTM A105 Body, 13Cr Trim, Bonnetless or WB, OS&Y, Plug
Type Disc, SW VGS-GF1
ID350 CL 3000 ASTM A216 WCC Body, 13Cr Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-GC3
Check 25 ~ 50 CL 4500 ASTM A105 Body, 13Cr Trim, WC, Lift Type, SW VCS-GF1
ID350 CL 3000 ASTM A216WCC Body, 13Cr Trim, PSC, Tilting Type, BW VCB-GC3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
151/174
PIPING MATERIAL CLASS
GB1
Rating ASME Class 4500
& Intermediate Class 3500
Material Low Alloy Steel (P91)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
HP Steam 283.0 550 3RY SH Outlet Drain 283.0 550
HP Steam Vent 283.0 550 Shoot Blowing Steam (Before CV) 288.0 525
The pipe wall thickness is calculated with the highest condition among above. 5D bend thinning allowance is applied to DN450 pipe wall thicknesses. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Forging Valves (Based on ASME B16.34 - Group 1.15 Class 4500)
Temp (℃) 500 538 550 575
Press (Barg) 423.0 375.8 374.2 359.1
For Casting Valves (Based on ASME B16.34 - Group 1.15 Class 3500)
The pressure-temperature rating is calculated in accordance with “B-4 Intermediate Rating Class Method” of ASME 16.34 Appendix B and the minimum valve wall thickness for intermediate rating valve body shall be complied with the code.
Temp (℃) 500 538 550 575
Press (Barg) 329.0 292.4 291.1 279.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASTM A335 Gr.P91
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 S/XXS 17.12
150 - 25.00
200 - 31.00
250 - 38.00
300 - 45.00
350 - 49.00
400 - 56.00
450 - 67.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASTM A182 F91 Forged End, SW ASME B16.11
65 ~ 450 ASTM A234 WP91 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
152/174
PIPING MATERIAL CLASS
GB1
Rating ASME Class 4500
& Intermediate Class 3500
Material Low Alloy Steel (P91)
Code ASME B31.1
Sockolet 25 ~ 50 CL.9000 ASTM A182 F91 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASTM A182 F91 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASTM A182 F91 Forged End, SW -
Plate A387Gr.91
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 4500 ASTM A182 F91 Body, F91 Trim, WB, OS&Y, Solid Wedge
Disc, SW VAS-GF9
80 ~ 450 CL 3500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-GC9 2,3
Globe 25 ~ 50 CL 4500 ASTM A182 F91 Body, F91 Trim, Bonnetless or WB, OS&Y,
Plug Type Disc, SW VGS-GF9
80 ~ 450 CL 3500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-GC9 2,3
Check 25 ~ 50 CL 4500 ASTM A182 F91 Body, F91 Trim, WC, Lift Type, SW VCS-GF9
80 ~ 450 CL 3500 ASTM A217 C12A Body, F91 Trim, PSC, Tilting Type, BW VCB-GC9 2,3
Angle 80 ~ 450 CL 3500 ASTM A217 C12A Body, F91 Trim, PSB, OS&Y, Angle Type, BW
VLB-GC9 2,3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Use normalized and tempered material only.
3. The deliberate addition of any element not listed in A217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
153/174
PIPING MATERIAL CLASS
GB1S
Rating ASME Class 4500
& Intermediate Class 3500
Material Low Alloy Steel (P91)
Code ASME SEC. I
(Boiler External Piping)
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
From 3Y SH Header To HP Turbine 283.0 550 Desuperheater Spray Water 288.0 525
3RY SH Outlet Drain 283.0 550 Shoot Blowing Steam(Before CV) 288.0 525
Desuperheater Vent 288.0 505
The pipe wall thickness is calculated with the highest condition among above. 5D bend thinning allowance is applied to DN450 pipe wall thicknesses. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits For Forging Valves (Based on ASME B16.34 - Group 1.15 Class 4500)
Temp (℃) 500 538 550 575
Press (Barg) 423.0 375.8 374.2 359.1
For Casting Valves (Based on ASME B16.34 - Group 1.15 Class 3500)
The pressure-temperature rating is calculated in accordance with “B-4 Intermediate Rating Class Method” of ASME 16.34 Appendix B and the minimum valve wall thickness for intermediate rating valve body shall be complied with the code.
Temp (℃) 500 538 550 575
Press (Barg) 329.0 292.4 291.1 279.3
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
25 S/XXS 9.09
ASME SA335 Gr.P91
SMLS, PE
ASME B36.10
40 S/XXS 10.15
50 S/XXS 11.07
65 S/XXS 14.02
SMLS, BE
80 S/XXS 15.24
100 S/XXS 17.12
150 - 25.00
200 - 31.00
250 - 38.00
300 - 45.00
350 - 49.00
400 - 56.00
450 - 67.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
25 ~ 50 CL 9000 ASME SA182 F91 Forged End, SW ASME B16.11
65 ~ 450 ASME SA234 WP91 SMLS, BW ASME B16.9 Schedule Match Pipe
1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
154/174
PIPING MATERIAL CLASS
GB1S
Rating ASME Class 4500
& Intermediate Class 3500
Material Low Alloy Steel (P91)
Code ASME SEC. I
(Boiler External Piping)
Sockolet 25 ~ 50 CL.9000 ASME SA182 F91 Forged End, SW MSS SP- 97
Weldolet 65 ~ - ASME SA182 F91 Forged End, BW MSS SP- 97
Boss 25~ 50 CL.9000 ASME SA182 F91 Forged End, SW -
Plate SA387Gr.91
Valves
Item Size (DN) Rating Description Material Code Note
Gate 25 ~ 50 CL 4500 ASME SA182 F91 Body, F91 Trim, WB, OS&Y, Solid Wedge
Disc, SW VAS-GF9-S
80 ~ 450 CL 3500 ASME SA217 C12A Body, F91 Trim, PSB, OS&Y, Parallel Slide Disc, BW
VAB-GC9-S 2,3
Globe 25 ~ 50 CL 4500 ASME SA182 F91 Body, F91 Trim, Bonnetless or WB,
OS&Y, Plug Type Disc, SW VGS-GF9-S
80 ~ 300 CL 3500 ASME SA217 C12A Body, F91 Trim, PSB, OS&Y, Cone Type Disc, BW
VGB-GC9-S 2,3
Check 25 ~ 50 CL4500 ASME SA182 F91 Body, F91 Trim, WC, Lift Type, SW VCS-GF9-S
80 ~ 450 CL 3500 ASME SA217 C12A Body, F91 Trim, PSC, Tilting Type, BW VCB-GC9-S 2,3
Angle 80 ~ 450 CL 3500 ASTM SA217 C12A Body, F91 Trim, PSB, OS&Y, Angle Type, BW
VLB-GC9-S 2,3
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. Use normalized and tempered material only.
3. The deliberate addition of any element not listed in SA217, Table 1 is prohibited, except Ca and Mg may be added for deoxidation.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
155/174
PIPING MATERIAL CLASS
GC1
Rating ASME Class 4500
Material Stainless Steel (316)
Code ASME B31.1
Service D.P.
(Barg) D.T. (℃)
Service D.P.
(Barg) D.T. (℃)
BFW Sampling 340.0 350 BCP Suction Sampling 298.0 382
HP Steam Sampling 283.0 550
The pipe wall thickness is calculated with the highest condition among above. Refer to Pipe Wall Thickness Calculation (S-00-TAA-P-71-001-001).
Pressure and Temperature Limits for Valves (Based on ASME B16.34 - Group 2.2 Class 4500)
Temp (℃) 350 400 500 538 550
Press (Barg) 454.9 441.6 423.0 375.8 374.2
Pipe
Item Size (DN) SCH. THK (mm)
Material Description Dimension Note
Pipe
15 - 6.00
ASTM A312 TP316 SMLS, PE ASME B36.19
2
20 - 7.00 2
25 - 8.00
Fittings
Item Size (DN) Rating Material Description Dimension Note
Elbow Tee Reducer Cap
15 ~ 25 CL 9000 ASTM A182 F316 Forged End, SW ASME B16.11
Sockolet 15 ~ 25 CL.9000 ASTM A182 F316 Forged End, SW MSS SP- 97
Boss 15 ~ 25 CL.9000 ASTM A182 F316 Forged End, SW -
Valves
Item Size (DN) Rating Description Material Code Note
Gate 15 ~ 25 CL 4500 ASTM A182 F316 Body, SS 316 Trim, WB, OS&Y, Solid Wedge Disc, SW
VAS-GF7 2
Globe 15 ~ 25 CL 4500 ASTM A182 F316 Body, SS 316 Trim, Bonnetless or WB, OS&Y, Plug Type Disc, SW
VGS-GF7 2
Check 15 ~ 25 CL 4500 ASTM A182 F316 Body, SS 316 Trim, WC, Lift Type, SW VCS-GF7 2
Note:
1. Schedule (thickness) shall be equal to or greater than that of pipe.
2. The size smaller than DN25 can be used for control lines, impulse lines and chemical dosing lines.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
156/174
Attachment – 3 : Piping Branch Table
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
157/174
Table I
M A I N
P I P E
S I Z E
15 R
20 R R Symbols S – Sockolet /Thredolet (Half Coupling/Boss) R - Socket Weld Tee T - Butt Weld Tee W - Weldolet G – Stub On (w/ Reinforced Plate If necessary)
25 R R R
40 R R R R
50 R R R R R
65 S S S S T T
80 S S S S T T T
100 S S S S S T T T
150 S S S S S T T T T
200 S S S S S W W T T T
250 S S S S S W W W T T T
300 S S S S S W W W T T T T
350 S S S S S W W W W T T T T
400 S S S S S W W W W T T T T T
450 S S S S S W W W W W T T T T T
500 S S S S S W W W W W T T T T T T
600 S S S S S W W W W W W T T T T T T
650 S S S S S W W W W W W T T T T T T T
700 S S S S S W W W W W W T T T T T T T T
750 S S S S S W W W W W W W W T T T T T T T
800 S S S S S W W W W W W W W T T T T T T T T
850 S S S S S W W W W W W W W T T T T T T T T T
900 S S S S S W W W W W W W W W T T T T T T T T T
1000 S S S S S W W W W W W W W W W T T T T T T T T T
1050 S S S S S W W W W W W W W W W W T T T T T T T T T
1100 S S S S S W W W W W W W W W W W T T T T T T T T T T
1200 S S S S S W W W W W W W W W W W T T T T T T T T T T T
1500 S S S S S W W W W W W W W W W W W G G G G G G G G G G G
1500
OVER S S S S S W W W W W W W W W W W W G G G G G G G G G G G G
15 20 25 40 50 65 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 1000 1050 1100 1200 1500 1500
OVER
BRANCH PIPE SIZE Note
1. The given table above shall be applied for CS, AS and SS.
2. Special branch connections such as for safety relief valve nozzle shall not applied to Piping Branch Table above.
3. Branch connections into blowdown and flare headers shall enter Side of header at 45 deg in the direction of flow.
4. Stub-On connection can be used for low pressure steam and circulating seawater instead of weldolet for DN350 and above.
5. The branch table of DN 1500 and above shall be only circulating seawater line.
6. The usage of the size smaller than DN25is limited to control lines, impulse lines and chemical dosing line.
7. Non-metal piping (GRP, CPVC, etc) shall be in accordance with manufacturer standard.
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
158/174
Attachment – 4 : Data Sheet for Manual Valves
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
159/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
1.1 Gate Valve Data Sheet
Gate AC2, AH3, BC1, CC1 VAS-CF6 15 ~ 50 ASME
600# A182 F316L STL SS 316 BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate DC1, EC1 VAS-EF7 15 ~ 50 ASME
1500# A182 F316 STL SS 316 WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate GC1 VAS-GF7 15 ~ 50 ASME
4500# A182 F316 STL SS 316 WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate AA1, AA2, AA3, AA6,
BA1, BA2, BA3, CA1 VAS-CF1 25 ~ 50
ASME
600# A105 STL 13Cr BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate BB1 VAS-CF4 25 ~ 50 ASME
600# A182 F11 CL.2 STL 13Cr BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate CB1 VAS-CF3 25 ~ 50 ASME
600# A182 F11 CL2 STL 13Cr BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate AC1,AC3 VAS-CF5 25 ~ 50 ASME
600# A182 F304L STL SS 304 BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate CC2 VAS-CF11 15 ~ 50 ASME
600# A182 F53 STL S32750 BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate CC2 VAT-CF11 15 ~ 50 ASME
600# A182 F53 STL S32750 BB, OS&Y Solid Wedge TE (NPT) ASME B 16.34 4
Gate CB2 VAS-CF9 25 ~ 50 ASME
600# A182 F91 STL 13Cr BB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate DA1,EA1 VAS-EF1 25 ~ 50 ASME
1500# A105 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate DB1,EB1 VAS-EF3 25 ~ 50 ASME
1500# A182 F11 CL.2 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate DB1S, EB1S VAS-EF3-S 25 ~ 50 ASME
1500# SA182 F11 CL.2 STL 13Cr WB, OS&Y Solid Wedge SW
ASME B 16.34 &
ASME SEC.I 4
Gate DB2, EB2 VAS-EF9 25 ~ 50 ASME
1500# A182 F91 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate FA1 VAS-FF1 25 ~ 50 ASME Special
2500# A105 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate FA1S VAS-FF1-S 25 ~ 50 ASME Special
2500# SA105 STL 13Cr WB, OS&Y Solid Wedge SW
ASME B 16.34
& ASME SEC.I 4
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
160/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Gate FB1 VAS-FF4 25 ~ 50 ASME Special
2500# A182 F22 CL.3 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate FB1S VAS-FF4-S 25 ~ 50 ASME Special
2500# SA182 F22 CL.3 STL 13Cr WB, OS&Y Solid Wedge SW
ASME B 16.34 &
ASME SEC.I 4
Gate GA1 VAS-GF1 25 ~ 50 ASME
4500# A105 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate GB1 VAS-GF9 25 ~ 50 ASME
4500# A182 F91 STL 13Cr WB, OS&Y Solid Wedge SW ASME B 16.34 4
Gate GB1S VAS-GF9-S 25 ~ 50 ASME
4500# SA182 F91 STL 13Cr WB, OS&Y Solid Wedge SW
ASME B 16.34 &
ASME SEC.I 4
Gate AC5, AG1, AH1 VAF-CF10 25 ~ 50 ASME
600# A182 F51 STL S31803 BB, OS&Y Solid Wedge FF ASME B 16.34 4
Gate AA4, AA7 VAT-CF1 25 ~ 50 ASME
600# A105 STL 13Cr BB, OS&Y Solid Wedge TE (NPT) ASME B 16.34 4
Gate AA1, AA2, AA3, AA6 VAB-AC2 80 ~ 800 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate AA2 VAB-AC2-L 80 ~ 800 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate AA1, AA2 VAB-AC2-W 80 ~ 800 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate AA2 VAB-AC2-LW 80 ~ 800 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate BA1, BA2, BA3 VAB-BC2 80 ~ 1200 ASME 300#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate BA1, BA3 VAB-BC2-L 80 ~ 1200 ASME 300#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate BA1, BA2 VAB-BC2-W 80 ~ 1200 ASME 300#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4
Gate BB1 VAB-BC6 80 ~ 550 ASME 300#
A217 WC9 STL 13Cr BB, OS&Y Flexible Wedge BW ASME B 16.34 4,5
Gate CA1 VAB-CC2 80 ~ 650 ASME 600#
A216 WCB STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate CB1 VAB-CC5 80 ~ 650 ASME 600#
A217 WC6 STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
161/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Gate CB2 VAB-CC9 80 ~ 200 ASME 600#
A217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate DA1 VAB-DC2 80 ~ 600 ASME 900#
A216 WCB STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate CB2 VAB-CC9-W 80 ~ 200 ASME 600#
A217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate DB2 VAB-DC9 80 ~ 700 ASME 900#
A217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate EA1 VAB-EC2 80 ~ 200 ASME 1500#
A216 WCB STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate EB1 VAB-EC5 80 ~ 600 ASME 1500#
A217 WC6 STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate EB1S VAB-EC5-S 80 ~ 600 ASME 1500#
SA217 WC6 STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate EB2 VAB-EC9 80 ~ 150 ASME 1500#
A217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate FA1 VAB-FC3 80 ~ 300 ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate FA1 VAB-FC3-L 80 ~ 300 ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate FA1 VAB-FC3-1 ID300, ID520
ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate FA1S VAB-FC3-S 80 ~ 600 ASME Special 2500#
SA216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate FA1S VAB-FC3-1S ID520 ASME Special 2500#
SA216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate FA1S VAB-FC3-1SL ID520 ASME Special 2500#
SA216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate FB1 VAB-FC6 80 ~ 150 ASME Special 2500#
A217 WC9 STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate FB1S VAB-FC6-S 80 ~ 150 ASME Special 2500#
SA217 WC9 STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate GA1 VAB-GC3 80 ~ 600 ASME 3000#
A216 WCC STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
162/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Gate GB1 VAB-GC9 80 ~ 450 ASME 3500#
A217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 4,5
Gate GB1S VAB-GC9-S 80 ~ 450 ASME 3500#
SA217 C12A STL 13Cr PSB, OS&Y Parallel Slide Disc BW ASME B 16.34 &
ASME SEC.I 4,5
Gate AA2, AA4, AA7 VAF-AC2 80 ~ 600 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Flexible Wedge RF or FF ASME B 16.34 4
Gate AC2 VAF-AC7 80 ~ 600 ASME 150#
A351 CF3M STL SS 316 BB, OS&Y Flexible Wedge RF ASME B 16.34 4
Gate AH3 VAF-AC7-1 80 ~ 400 ASME 150#
A351 CF3M STL SS 316 BB, OS&Y Flexible Wedge FF ASME B 16.34 4
Gate AH3 VAF-AC7-1W 80 ~ 400 ASME 150#
A351 CF3M STL SS 316 BB, OS&Y Flexible Wedge FF ASME B 16.34 4
Gate AC1 VAF-AC10 80 ~ 500 ASME 150#
A351 CF3 STL SS 304 BB, OS&Y Flexible Wedge RF ASME B 16.34 4
Gate AC5, AG1, AH1 VAF-AC12 80 ~ 200 ASME 150#
A995 CD3MN STL S31803 BB, OS&Y Flexible Wedge FF ASME B 16.34 4
Gate CC2 VAF-CC13 80 ~ 250 ASME 600#
A995 CE3MN (GR. 5A)
STL S32750 BB, OS&Y Flexible Wedge RF ASME B 16.34 4
Gate AG2 VAF-AP1 80 ~ 300 Maker Std PVC PVC PVC SB, ISRS PVC Wedge FF ASME B 16.34 4
Gate BC1 VAF-BC7 80 ~ 250 ASME 300#
A351 CF3M STL SS 316 BB, OS&Y Flexible Wedge RF ASME B 16.34 4
1.2 GLOBE VALVE DATA SHEET
Globe AC2, AH3, BC1, CC1 VGS-CF6 15 ~ 50 ASME
600# A182 F316L STL SS 316 BB, OS&Y Plug Disc SW ASME B 16.34 2, 4
Globe CC2 VGS-CF11 15 ~ 50 ASME
600# A182 F53 STL S32750 BB, OS&Y Plug Disc SW ASME B 16.34 2, 4
Globe DC1, EC1 VGS-EF7 15 ~ 50 ASME
1500# A182 F316 STL SS 316
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe GC1 VGS-GF7 15 ~ 50 ASME
4500# A182 F316 STL SS 316
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe CC1 VGT-CF6 25 ASME
600# A182 F316L STL SS 316 BB, OS&Y Plug Disc NPT ASME B 16.34 2, 4
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
163/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Globe AA1, AA2, AA3, AA6BA1, BA2, BA3, CA1
VGZ-CF1 25 ASME 600#
A105 STL 13Cr BB, OS&Y Plug Disc SWxNPT ASME B 16.34 2,4
Globe AC1 VGZ-CF5 25 ASME
600# A182 F304L STL SS 304 BB, OS&Y Plug Disc SWxNPT ASME B 16.34 2,4
Globe AC2, AC4, BC1 VGZ-CF6 25 ASME
600# A182 F316L STL SS 316 BB, OS&Y Plug Disc SWxNPT ASME B 16.34 2,4
Globe AA1, AA2, AA3, AA6BA1, BA2, BA3, CA1
VGS-CF1 25 ~ 50 ASME 600#
A105 STL 13Cr BB, OS&Y Plug Disc SW ASME B 16.34 2,4
Globe BB1 VGS-CF4 25 ~ 50 ASME
600#
A182 F22
CL.3 STL 13Cr BB, OS&Y Plug Disc SW ASME B 16.34 2,4
Globe CB1 VGS-CF3 25 ~ 50 ASME
600#
A182 F11
CL.2 STL 13Cr BB, OS&Y Plug Disc SW ASME B 16.34 2,4
Globe AC1,AC3 VGS-CF5 25 ~ 50 ASME
600# A182 F304L STL SS 304 BB, OS&Y Plug Disc SW ASME B 16.34 2,4
Globe CB2 VGS-CF9 25 ~ 50 ASME
600# A182 F91 STL 13Cr BB, OS&Y Plug Disc SW ASME B 16.34 2,4
Globe DA1, EA1 VGS-EF1 25 ~ 50 ASME
1500# A105 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe DB1, EB1 VGS-EF3 25 ~ 50 ASME
1500#
A182 F11
CL.2 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe DB1S, EB1S VGS-EF3-S 25 ~ 50 ASME
1500#
SA182 F11
CL.2 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 &
ASME SEC.I 2,4
Globe DB2, EB2 VGS-EF9 25 ~ 50 ASME
1500# A182 F91 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe FA1 VGS-FF1 25 ~ 50 ASME Special
2500# A105 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe FA1S VGS-FF1-S 25 ~ 50 ASME Special
2500# SA105 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 &
ASME SEC.I 2,4
Globe FB1 VGS-FF4 25 ~ 50 ASME Special
2500#
A182 F22 CL.3
STL 13Cr Bonnetless or WB,
OS&Y Plug Disc SW ASME B 16.34 2,4
Globe FB1S VGS-FF4-S 25 ~ 50 ASME Special
2500#
SA182 F22 CL.3
STL 13Cr Bonnetless or WB,
OS&Y Plug Disc SW
ASME B 16.34 & ASME SEC.I
2,4
Globe GA1 VGS-GF1 25 ~ 50 ASME
4500# A105 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
164/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Globe GB1 VGS-GF9 25 ~ 50 ASME
4500# A182 F91 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 2,4
Globe GB1S VGS-GF9-S 25 ~ 50 ASME
4500# SA182 F91 STL 13Cr
Bonnetless or WB, OS&Y
Plug Disc SW ASME B 16.34 &
ASME SEC.I 2,4
Globe AA1, AA2, AA3, AA6 VGB-AC2 80 ~ 600 ASME
150# A216 WCB STL 13Cr BB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe BA1, BA2, BA3 VGB-BC2 80 ~ 600 ASME
300# A216 WCB STL 13Cr BB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe BA2 VGB-BC2-L 80 ~ 600 ASME
300# A216 WCB STL 13Cr BB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe BA1, BA2 VGB-BC2-W 80 ~ 600 ASME
300# A216 WCB STL 13Cr BB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe CA1 VGB-CC2 80 ~ 650 ASME
600# A216 WCB STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe BB1 VGB-BC6 80 ~ 550 ASME
300# A217 WC9 STL 13Cr BB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe CB1 VGB-CC5 80 ~ 550 ASME
600# A217 WC6 STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe CB2 VGB-CC9 80 ~ 200 ASME
600# A217 C12A STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe DA1 VGB-DC2 80 ~ 400 ASME
900# A216 WCB STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe DB2 VGB-DC9 80 ~ 400 ASME
900# A217 C12A STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe EA1 VGB-EC2 80~ 200 ASME
1500# A216 WCB STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe EB1 VGB-EC5 80 ~ 600 ASME
1500# A217 WC6 STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe EB1S VGB-EC5-S 80 ~ 600 ASME
1500# SA217 WC6 STL 13Cr PSB, OS&Y Cone Disc BW
ASME B 16.34 &
ASME SEC.I 2,4
Globe EB2 VGB-EC9 80 ~ 150 ASME
1500# A217 C12A STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe FA1 VGB-FC3 80 ~ 300 ASME Special
2500# A216 WCC STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
165/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Globe FA1 VGB-FC3-L 80 ~ 300 ASME Special
2500# A216 WCC STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe FA1S VGB-FC3-S 80 ~ 300 ASME Special
2500# SA216 WCC STL 13Cr PSB, OS&Y Cone Disc BW
ASME B 16.34 &
ASME SEC.I 2,4
Globe FB1 VGB-FC6 80 ~ 150 ASME Special
2500# A217 WC9 STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe FB1S VGB-FC6-S 80 ~ 150 ASME Special
2500# SA217 WC9 STL 13Cr PSB, OS&Y Cone Disc BW
ASME B 16.34 &
ASME SEC.I 2,4
Globe GA1 VGB-GC3 80 ~ 600 ASME
3000# A216 WCC STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe GB1 VGB-GC9 80~ 300 ASME
3500# A217 C12A STL 13Cr PSB, OS&Y Cone Disc BW ASME B 16.34 2,4
Globe GB1S VGB-GC9-S 80 ~ 300 ASME
3500# SA217 C12A STL 13Cr PSB, OS&Y Cone Disc BW
ASME B 16.34 &
ASME SEC.I 2,4
Globe AA4, AA7 VGF-AC2 80 ~ 600 ASME
150# A216 WCB STL 13Cr BB, OS&Y Cone Disc RF or FF ASME B16.34 2,4
Globe AC2 VGF-AC7 80 ~ 600 ASME
150# A351 CF3M STL SS 316 BB, OS&Y Cone Disc RF ASME B16.34 2,4
Globe AC2, AG4, AH3 VGF-AC7-1 80 ~ 400 ASME
150# A351 CF3M STL SS 316 BB, OS&Y Cone Disc FF ASME B16.34 2,4
Globe AH3 VGF-AC7-1W 80 ~ 400 ASME
150# A351 CF3M STL SS 316 BB, OS&Y Cone Disc FF ASME B16.34 2,4
Globe AC1, AC3 VGF-AC10 80 ~ 500 ASME
150# A351 CF3 STL SS 304 BB, OS&Y Cone Disc RF ASME B 16.34 2,4
Globe AC5, AG1,AG3, AH1 VGF-AC12 80 ~ 200 ASME
150# A995 CD3MN STL S31803 BB, OS&Y Cone Disc FF ASME B 16.34 2,4
Globe CC2 VGF-CC13 80 ~ 250 ASME
600#
A995 CE3MN
(GR. 5A) STL S32750 BB, OS&Y Cone Disc RF ASME B 16.34 2,4
Globe BC1 VGF-BC7 80 ~ 250 ASME
300# A351 CF3M STL SS 316 BB, OS&Y Cone Disc RF ASME B16.34 2,4
Globe AG4 VGF-CF6 25 ~ 50 ASME
600# A182 F316L STL SS 316 BB, OS&Y Plug Disc FF ASME B 16.34 2, 4
Globe AC5, AG1,AG3, AH1,
AH2 VGF-CF10 25 ~ 50
ASME
600# A182 F51 STL S31803 BB, OS&Y Plug Disc FF ASME B 16.34 2,4
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
166/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
Globe AF1, AG2 VGF-AP1 25 ~ 300 Maker Std PVC PVC PVC SB, ISRS Cone Disc FF ASME B 16.34 2,4
Globe AA4, AA7 VGT-CF1 25 ~ 50 ASME
600# A105 STL 13Cr BB, OS&Y Plug Disc TE (NPT) ASME B 16.34 2,4
1.3 NEEDLE VALVE DATA SHEET
Needle BA1, BA3 VNS-CF1 25 ~ 50 ASME 600#
A105 STL 13Cr BB, OS&Y Needle Disc SW ASME B16.34
Needle FA1 VNS-FF1 25 ~ 50 ASME Special 2500#
A105 STL 13Cr Bonnetless or WB,
OS&Y Needle Disc SW ASME B16.34
Needle FA1S VNS-FF1-S 25 ~ 50 ASME Special
2500# SA105 STL 13Cr
Bonnetless or WB, OS&Y
Needle Disc SW ASME B16.34&
ASME SEC.I
Needle AA2 VNB-AC2 80 ~ 600 ASME 150#
A216 WCB STL 13Cr BB, OS&Y Needle Disc BW ASME B16.34
Needle BA1, BA3 VNB-BC2 80 ~ 600 ASME 300#
A216 WCB STL 13Cr BB, OS&Y Needle Disc BW ASME B16.34
Needle FA1 VNB-FC3 80 ~ 600 ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Needle Disc BW ASME B16.34
Needle FA1S VNB-FC3-S 80 ~ 600 ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Needle Disc BW ASME B16.34&
ASME SEC.I
1.4 ANGLE VALVE DATA SHEET
Angle BA1 VLS-CF1 25~50 ASME 600#
A105 STL 13Cr BB, OS&Y Angle Type SW ASME B16.34 2
Angle DB2 VLB-DC9 80 ~ 600 ASME 900#
A217 C12A STL 13Cr PSB, OS&Y Angle Type BW ASME B16.34 2
Angle GB1 VLB-GC9 80 ~ 600 ASME 3500#
A217 C12A STL 13Cr PSB, OS&Y Angle Type BW ASME B16.34 2
Angle GB1S VLB-GC9-S 80 ~ 450 ASME 3500#
SA217 C12A STL 13Cr PSB, OS&Y Angle Type BW ASME B16.34&
ASME SEC.I 2
1.5 STOP CHECK VALVE DATA SHEET
STOP CHECK
AC2, BC1 VTS-CF6 25 ASME 600# A182 F316L STL SS 316 BB, OS&Y Stop Check SW ASME B16.34
STOP CHECK
AG4 VTF-CF6 25 ASME 600# A182 F316L STL SS 316 BB, OS&Y Stop Check FF ASME B16.34
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
167/174
Valve Data Sheet (Gate / Globe / Needle / Angle)
Type Piping Material
Class Code
Size (DN)
Class
Material Type End
CONN Design &
Requirement Note
Body, Bonnet Disc & Body
Seat Surface
Stem Body/Bonnet Disc
STOP CHECK
EB2 VTB-EC9 150 ASME 1500# A217 C12A STL 13Cr PSB, OS&Y Stop Check BW ASME B16.34
STOP CHECK
FA1 VTB-FC3 80 ASME Special 2500#
A216 WCC STL 13Cr PSB, OS&Y Stop Check BW ASME B16.34
STOP CHECK
FA1S VTB-FC3-S 80 ~ 400 ASME Special 2500#
SA216 WCC STL 13Cr PSB, OS&Y Stop Check BW ASME B16.34 &
ASME SEC.I
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
168/174
Valve Data Sheet (Check)
Type Piping Material
Class Code
Size (DN)
Class Material Type
End CONN
Design & Requirement
Note Body, Bonnet
Disc & Body SeatSurface
Spring Body/Bonnet Disc
2.1 Check valve data sheet
Check AC2, AC4, AH3, BC1,
CC1 VCS-CF6 15 ~ 50 ASME
600# A182 F316L STL - BC Lift Check SW ASME B 16.34
Check CC2 VCS-CF11 15 ~ 50 ASME
600# A182 F53 STL - BC Lift Check SW ASME B 16.34
Check DC1, EC1 VCS-EF7 15 ~ 50 ASME
1500# A182 F316 STL - WC Lift Check SW ASME B 16.34
Check GC1 VCS-GF7 15 ~ 50 ASME
4500# A182 F316 STL - WC Lift Check SW ASME B 16.34
Check AA1, AA2, AA3, AA6
BA1, BA2, BA3, CA1VCS-CF1 25 ~ 50
ASME
600# A105 STL - BC Lift Check SW ASME B16.34
Check BB1 VCS-CF4 25 ~ 50 ASME
600# A182 F22 CL.3 STL - BC Lift Check SW ASME B16.34
Check CB1 VCS-CF3 25 ~ 50 ASME
600# A182 F11 CL.2 STL - BC Lift Check SW ASME B16.34
Check AC1, AC3 VCS-CF5 25 ~ 50 ASME
600# A182 F304L STL - BC Lift Check SW ASME B 16.34
Check CB2 VCS-CF9 25 ~ 50 ASME
600# A182 F91 STL - BC Lift Check SW ASME B16.34
Check DA1, EA1 VCS-EF1 25 ~ 50 ASME
1500# A105 STL - WC Lift Check SW ASME B 16.34
Check DB1, EB1 VCS-EF3 25 ~ 50 ASME
1500# A182 F11 CL.2 STL - WC Lift Check SW ASME B16.34
Check DB1S, EB1S VCS-EF3-S 25 ~ 50 ASME
1500#
SA182 F11
CL.2 STL - WC Lift Check SW
ASME B16.34 &
ASME SEC.I
Check DB2 VCS-EF9 25 ~ 50 ASME
1500# A182 F91 STL - WC Lift Check SW ASME B16.34
Check FA1 VCS-FF1 25 ~ 50 ASME Special
2500# A105 STL - WC Lift Check SW ASME B16.34
Check FA1S VCS-FF1-S 25 ~ 50 ASME Special
2500# SA105 STL - WC Lift Check SW
ASME B16.34 &
ASME SEC.I
Check FB1 VCS-FF4 25 ~ 50 ASME Special
2500# A182 F22 CL.3 STL - WC Lift Check SW ASME B 16.34
Check FB1S VCS-FF4-S 25 ~ 50 ASME Special
2500#
SA182 F22
CL.3 STL - WC Lift Check SW
ASME B16.34 &
ASME SEC.I
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
169/174
Valve Data Sheet (Check)
Type Piping Material
Class Code
Size (DN)
Class Material Type
End CONN
Design & Requirement
Note Body, Bonnet
Disc & Body SeatSurface
Spring Body/Bonnet Disc
Check GA1 VCS-GF1 25 ~ 50 ASME
4500# A105 STL - WC Lift Check SW ASME B16.34
Check GB1 VCS-GF9 25 ~ 50 ASME
4500# A182 F91 STL - WC Lift Check SW ASME B16.34
Check GB1S VCS-GF9-S 25 ~ 50 ASME
4500# SA182 F91 STL - WC Lift Check SW
ASME B16.34 &
ASME SEC.I
Check AA1, AA2, AA3, AA6 VCB-AC2 80 ~ 600 ASME
150# A216 WCB STL BC
Swing Check Inner Shaft BW ASME B 16.34 3
Check BA1, BA2, BA3 VCB-BC2 80 ~ 600 ASME
300# A216 WCB STL BC
Swing Check Inner Shaft BW ASME B 16.34 3
Check BB1 VCB-BC6 80 ~ 550 ASME
300# A217 WC9 STL BC
Swing Check Inner Shaft BW ASME B 16.34 3
Check CA1 VCB-CC2 80 ~ 600 ASME
600# A216 WCB STL PSC
Swing Check Inner Shaft BW ASME B 16.34 3
Check CB1 VCB-CC5 80 ~ 650 ASME
600# A217 WC6 STL PSC
Swing Check Inner Shaft BW ASME B 16.34 3
Check CB2 VCB-CC9 80 ~ 200 ASME
600# A217 C12A STL PSC
Swing Check Inner Shaft BW ASME B 16.34 3
Check DA1 VCB-DC2 80 ~ 600 ASME
900# A216 WCB STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check DB2 VCB-DC9 80 ~ 600 ASME
900# A217 C12A STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check EA1 VCB-EC2 80 ~ 200 ASME
1500# A216 WCB STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check EB1 VCB-EC5 80 ~ 600 ASME
1500# A217 WC6 STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check EB1S VCB-EC5-S 80 ~ 600 ASME
1500# SA217 WC6 STL PSC
Tilting Check Inner Shaft BW
ASME B16.34 &
ASME SEC.I 3
Check FA1 VCB-FC3 80 ~ 300 ASME Special
2500# A216 WCC STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check FA1S VCB-FC3-S 80 ~ 300 ASME Special
2500# SA216 WCC STL PSC
Tilting Check Inner Shaft BW
ASME B16.34 &
ASME SEC.I 3
Check FB1 VCB-FC6 80 ~ 150 ASME Special
2500# A217 WC9 STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check FB1S VCB-FC6-S 80 ~ 150 ASME Special
2500# SA217 WC9 STL PSC
Tilting Check Inner Shaft BW
ASME B16.34 &
ASME SEC.I 3
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
170/174
Valve Data Sheet (Check)
Type Piping Material
Class Code
Size (DN)
Class Material Type
End CONN
Design & Requirement
Note Body, Bonnet
Disc & Body SeatSurface
Spring Body/Bonnet Disc
Check GA1 VCB-GC3 80 ~ 600 ASME
3000# A216 WCC STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check GB1 VCB-GC9 80 ~ 450 ASME
3500# A217 C12A STL PSC
Tilting Check Inner Shaft BW ASME B 16.34 3
Check GB1S VCB-GC9-S 80 ~ 450 ASME
3500# SA217 C12A STL PSC
Tilting Check Inner Shaft BW
ASME B16.34 &
ASME SEC.I 3
Check AA4, AA7 VCT-CF1 25 ~ 50 ASME
600# A105 STL - BC Lift Check TE (NPT) ASME B16.34
Check AG4 VCF-CF6 25 ~ 50 ASME
600# A182 F316L STL - BC Lift Check FF ASME B 16.34
Check AC5, AG1, AH1, AH2 VCF-CF10 25 ~ 50 ASME
600# A182 F51 STL - BC Lift Check FF ASME B16.34
Check AA4,AA7 VCF-AC2 80 ~ 600 ASME
150# A216 WCB STL - BC
Swing Check Inner Shaft RF or FF ASME B 16.34 3
Check AC2, AC4 VCF-AC7 80 ~ 600 ASME
150# A351 CF3M STL - BC
Swing Check Inner Shaft RF ASME B 16.34 3
Check AC2, AG4, AH3 VCF-AC7-1 80 ~ 400 ASME
150# A351 CF3M STL - BC
Swing Check Inner Shaft FF ASME B 16.34 3
Check AC1 VCF-AC10 80 ~ 500 ASME
150# A351 CF3 STL - BC
Swing Check Inner Shaft RF ASME B 16.34 3
Check AC5, AG1, AG3,AH1,
AH2 VCF-AC12 80 ~ 250
ASME
150# A995 CD3MN STL - BC
Swing Check Inner Shaft FF ASME B 16.34 3
Check CC2 VCF-CC13 80 ~ 250 ASME
600#
A995 CE3MN
(GR. 5A) STL - BC
Swing Check Inner Shaft RF ASME B 16.34 3
Check AF1 VCF-AP1 25 ~ 300 Maker Std PVC - - BC Swing Check Inner Shaft FF ASME B 16.34 3
Check AG1, AH1, AH2 VCF-AC2-R 200 ~ 600 ASME
150#
A216 WCB
with Rubber
Lined
SS31803 Inconel
X750 - Dual Plate Check FF ASME B 16.34
Check AG1, AH1 VCF-AC2-R1 650 ~ 3600 ASME
150#
A216 WCB
with Rubber
Lined
SS31803 Inconel
X750 - Dual Plate Check FF
API 594 & AWWA
C207 CL.D
Check AA1, AA2, AA3 VCF-AC2-1 650 ~ 900 ASME
150# A216 WCB STL
Inconel
X750 - Dual Plate Check RF
API 594, ASME
B16.47 Ser.A
Check BA1, BA3 VCF-BC2-1 650 ~ 1300 ASME
300# A216 WCB STL
Inconel
X750 - Dual Plate Check RF
API 594, ASME
B16.47 Ser.A
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
171/174
Valve Data Sheet (Check)
Type Piping Material
Class Code
Size (DN)
Class Material Type
End CONN
Design & Requirement
Note Body, Bonnet
Disc & Body SeatSurface
Spring Body/Bonnet Disc
Check BC1 VCF-BC7 80 ~ 250 ASME
300# A351 CF3M STL - BC
Swing Check Inner Shaft RF ASME B 16.34 3
Check AF2 VCF-AP2 15 ~ 50 ASME
150# CPVC CPVC - BC Ball Check FF ASME B 16.34
Check AF2 VCF-AP2-1 80 ~ 300 ASME
150# CPVC CPVC - BC
Swing Check Inner Shaft FF ASME B 16.34
Check AH5 VCF-CF1-T 20 ~ 400 ASME
150#
A216 WCB +
Teflon Lined PTFE - BC Lift Check RF ASME B 16.34
Valve Data Sheet (Butterfly / Ball/SBB)
Type Piping Material
Class Code
Size (DN)
Class Material
Design Type End Conn.Design &
Requirement Note Body,
Bonnet Disc
Body Seat Surface
Stem
3.1 Butterfly Valve Data Sheet
Butterfly AA1, AA2, AA6 VFF-AC2 80 ~ 600 ASME 150#
A216 WCB A351 CF8 EPDM 13Cr Eccentric Design, EPDM Seated RF API 609 1
Butterfly AA2 VFF-AC2-1 650~850 ASME 150#
A216 WCB A351 CF8 EPDM 13Cr Eccentric Design, EPDM Seated RF AWWAC504 & ASME B16.47
Ser.A 1
Butterfly AA5 VFF-AC2-2 80 ~ 600 ASME 150#
A216 WCB A351 CF8 EPDM 13Cr Concentric Design, EPDM Seated FF API 609 1
Butterfly AG4 VFW-AC7 80 ~ 600 ASME 150#
A351 CF3M A351 CF3M EPDM 13Cr Concentric Design, EPDM Seated Wafer Lug API 609 Cat A 1
Butterfly CC2 VFW-CC13 80 ~ 250 ASME 600#
A995 CE3MN (GR. 5A)
S32750 RTFE S32750 Eccentric Design, REFE Seated Wafer Lug API 609 Cat.B 1
Butterfly AA5 VFF-AC2-3 650 ~ 850 ASME 150#
A216 WCB A351 CF8 EPDM 13Cr Eccentric Design, EPDM Seated FF AWWAC504 & ASME B16.47
Ser.A 1
Butterfly AG1,AH1,AH2 VFF-AC2-R 200 ~ 600 ASME 150#
A216 WCB with Rubber
lined
A216 WCB with Rubber lined
EPDM S31803 Eccentric Design, EPDM Seated FF API 609 1
Butterfly AG1,AH1 VFF-AC2-R1 650 ~ 3600 ASME 150#
A216 WCB with Rubber
lined
A216 WCB with Rubber lined
EPDM S31803 Eccentric Design, EPDM Seated FF AWWAC504/C516
& C207 CL.D 1
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
172/174
Valve Data Sheet (Butterfly / Ball/SBB)
Type Piping Material
Class Code
Size (DN)
Class Material
Design Type End Conn.Design &
Requirement Note Body,
Bonnet Disc
Body Seat Surface
Stem
Butterfly AC2,AC4 VFF-AC7 80 ~ 600 ASME 150#
A351 CF3M A351 CF3M EPDM SS 316L Eccentric Design, EPDM Seated RF API 609 1
Butterfly AC4 VFF-AC7-3 80 ~ 600 ASME 150#
A351 CF3M A351 CF3M EPDM SS 316L Concentric Design, EPDM Seated RF API 609 Cat A 1
Butterfly AC2, AH3 VFF-AC7-1 80 ~ 400 ASME 150#
A351 CF3M A351 CF3M EPDM SS 316L Eccentric Design, EPDM Seated FF API 609 1
Butterfly AC2 VFF-AC7-2 700 ASME 150#
A351 CF3M A351 CF3M EPDM SS 316L Eccentric Design, EPDM Seated RF AWWAC504 & ASME B16.47
Ser.A 1
Butterfly AG1, AH1,AH2 VFF-AC12 80 ~ 250 ASME 150#
A995 CD3MN
S31803 EPDM S31803 Eccentric Design, EPDM Seated FF API 609 1
Butterfly AF2 VFW-AP2 80 ~ 300 ASME 150#
CPVC CPVC EPDM SS 316 Concentric Design, EPDM Seated Wafer API 609 1
Butterfly AC1 VFF-AC10 80 ~ 600 ASME 150#
A351 CF3 A351 CF3 EPDM SS 304L Eccentric Design, EPDM Seated RF API 609 1
3.2 Ball Valve Data Sheet
Ball AC2, AC4, AH3, BC1 VBS-CF6 15 ~ 50 ASME 600#
A182 F316L SS 316L RTFE / PTFE SS 316L Floating Ball, Side Entry with 75mm S/40S Nipples, Full Port,
SW ASME B16.34 &
API 607(Fire Safe)
Ball CC2 VBB-CF11 15 ~ 50 ASME 600#
A182 F53 S32750 RTFE S32750 Floating Ball, Side Entry with 75mm S/40S Nipples, Full Port,
SW ASME B16.34 &API 607(Fire
Safe)
Ball AF2, AA7 VBT-AP2 15 ~ 50 ASME 150#
CPVC CPVC PTFE CPVC Floating Ball, Side Entry, Full Port TE
(NPT) ASME B16.34
Ball AA1,AA2, BA2 VBS-CF1 25 ~ 50 ASME 600#
A105 SS 304 RTFE / PTFE SS 304 Floating Ball, Side Entry with 75mm S/80 Nipples, Full Port,
SW ASME B16.34 &
API 607(Fire Safe)
Ball AA3,BA3 VBS-CF1-1 25 ~ 50 ASME 600#
A105 SS 304 RTFE / PTFE SS 304 Floating Ball, Top Entry with 75mm S/80 Nipples, Full Port,
SW ASME B16.34 &
API 607(Fire Safe)
Ball AC1 VBS-CF5 25 ~ 50 ASME 600#
A182 F304L SS 304 RTFE / PTFE SS 304 Floating Ball, Side Entry with 75mm S/40S Nipples, Full Port,
SW ASME B16.34 &
API 607(Fire Safe)
Ball AA4, AA5 VBT-CF1 25 ~ 50 ASME 600#
A105 SS 304 RTFE / PTFE SS 304 Floating Ball, Side Entry, Full Port, Long Pattern
TE (NPT) ASME B16.34 &
API 607(Fire Safe)
Ball AA3 VBB-AC2 80 ~ 150 ASME 150#
A216 WCB A105 + ENP or
SS 304 RTFE / PTFE SS 304 Floating Ball, Top Entry,
Full Port, Long Pattern BW
ASME B16.34 & API 607(Fire Safe)
Ball AA3 VBB-AC2-1 200 ~ 850 ASME 150#
A216 WCB A105 + ENP or
SS 304 RTFE / PTFE SS 304 Trunnion Ball, Top Entry,
Full Port, Long Pattern BW
ASME B16.34 & API 607(Fire Safe)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
173/174
Valve Data Sheet (Butterfly / Ball/SBB)
Type Piping Material
Class Code
Size (DN)
Class Material
Design Type End Conn.Design &
Requirement Note Body,
Bonnet Disc
Body Seat Surface
Stem
Ball AC1,AC3 VBF-AC10 80 ~ 150 ASME 150#
A351 CF3 SS304 RTFE / PTFE SS 304 Floating Ball, Side Entry, Full Port, Long Pattern
RF ASME B16.34 &
API 607(Fire Safe)
Ball AG1, AH1 VBF-AC12 80 ~ 150 ASME 150#
A995 CD3MN
S31803 RTFE / PTFE S31803 Floating Ball, Side Entry, Full Port, Long Pattern
FF ASME B16.34 &
API 607(Fire Safe)
Ball AA1, AA2,AA4,AA7 VBF-AC2 80 ~ 150 ASME 150#
A216 WCB A105 + ENP or
SS 304 RTFE / PTFE SS 304
Floating Ball, Side Entry, Full Port, Long Pattern
RF or FF ASME B16.34 &
API 607(Fire Safe)
Ball BA3 VBB-BC2 80 ~ 100 ASME 300#
A216 WCB A105 + ENP or
SS 304 RTFE / PTFE SS 304
Floating Ball, Top Entry, Full Port, Long Pattern
BW ASME B16.34 &
API 607(Fire Safe)
Ball BA3 VBB-BC2-1 150 ~ 1200 ASME 300#
A216 WCB A105 + ENP or
SS 304 RTFE / PTFE SS 304
Trunnion Ball, Top Entry, Full Port, Long Pattern
BW ASME B16.34 &
API 607(Fire Safe)
Ball BC1 VBF-BC7 80~200 ASME 300#
A351CF3M SS 316L RTFE / PTFE SS 316L Floating Ball, Side Entry Full Port, Long Pattern
RF ASME B16.34 &
API 607(Fire Safe)
Ball AF2 VBF-AP2 All ASME 150#
CPVC CPVC PTFE CPVC Floating Ball, Side Entry, Full Port FF ASME B16.34
Ball AF2 VBT-AP2 All ASME 150#
CPVC CPVC PTFE CPVC Floating Ball, Side Entry, Full Port TE ASME B16.34
Ball AH5 VBF-AC2-T 20 ~ 400 ASME 150#
A216 WCB + Teflon
Lined
C.S + Teflon Lined
PTFE SS 304 Floating Ball, Side Entry, Full Port RF ASME B16.34 &
API 607(Fire Safe)
Ball AG4 VBF-CF6 25 ~ 50 ASME 600#
A182 F316L SS 316L RTFE / PTFE SS 316L Floating Ball, Side Entry, Full Port, FF ASME B16.34
Ball AG1 VBF-CF10 15 ~ 50 ASME 600#
A182 F51 S31803 RTFE Duplex Floating Ball, Side Entry, Full Port FF ASME B16.34 &
API 607(Fire Safe)
3.3 Single Block Bleed Valve Data sheet
SBB AG1, AG3, AH1 VSM-CF10 40x25 25x25, 50x25
ASME 600#
A182 F51 S31803 RTFE/PTFE S31803 Floating Ball FFxNPT ASME B16.34 &
API 607(Fire Safe)
SBB AH3 VSM-CF6 50x25 ASME 600#
A182 F316L SS 316L RTFE/PTFE SS 316L Floating Ball FFxNPT ASME B16.34 &
API 607(Fire Safe)
Piping Material Specification
Doc No : S-00-TAA-P-38-002-001 Rev No : B
174/174
Valve Data Sheet (Diaphragm)
Type Piping Material
Class Code
Size (DN)
Class Material
Design Type End Conn.Design &
Requirement Note
Body, Bonnet Diaphragm Stem
4.1 Diaphragm Valve Data Sheet
Diaphragm AF2 VDF-AP2 All ASME 150#
CPVC PTFE or EPDM - FF
Diaphragm AG4 VDF-AC2-R 20 ~ 200 ASME 150#
A216 WCB + Rubber Lined
EPDM - FF
Diaphragm AH5 VDF-AC2-T 20 ~ 400 ASME 150#
A216 WCB + Teflon Lined
PTFE - RF
Note: 1. Sealing between the disc and body of butterfly type valves shall be renewable metal to rubber facings secured to the disc and body in an approved number.
2. Where globe or angle style valves are used they shall be installed with the normal flow entering beneath the disc.
3. Check valves shall be of the inner-shaft type and no stuffing box or counterweight type check valve shall be permitted.
4. All gate and globe valves shall have back-back seat features to prevent process flow migrating into the packing box.
5. Means shall be provided to prevent any accumulation of pressure between the discs of high pressure steam or feed parallel slide valves. In the case of valves with by-passes, the integrate space of
the main valve shall be connected to the integrate space of the by-pass valve.