KX-NS8188 E1 AdapterKX-NS8290 PRI AdapterProduct InformationRev 1.1E January 09, 2013
Specifications and schedule are subject to change without notice.Specifications and schedule are subject to change without notice.
Panasonic System NetworksPanasonic System NetworksPBX SE team PBX SE team
NS1000 Version 2NS1000 Version 2Document for SE and Sales TrainingDocument for SE and Sales Training
2
When customers want to use IP-Phone (*) mainly for extension and they want to use E1 or more than 2 PRI as trunk, KX-NS1000 version 2 with new trunk adapter is recommended because KX-NS1000 supports more IP capacity and IP functionality than KX-NCP or KX-TDE.(*)- KX-NT / KX-UT by Panasonic- NT based software phone by Panasonic- SIP hardware phone by other maker- SIP software phone for PC, Android, iPhone and so on
1. Introduction
Model Specifications
KX-NS8188X E1 adapter on SIP trunk
KX-NS8290CE PRI30 adapter on SIP trunk
KX-NS8290X PRI23 adapter on SIP trunk
Trunk Adaptor
SIP Trunk (30-ch)
PRI30
SIP Extension
PanasonicKX-NS8290
PRI30
PRI Card
OtherSIP Phone
SIPSoftphone
KX-NT KX-UT
IP Network
KX-NS1000
KX-NCS0290
215 mm (W)44 mm (H)
200 mm (D)
500g
3
Before adding KX-NS1000 After adding KX-NS1000
Stacking Card
AnalogCO
KX-TDE
CO Card
KX-DT w/DSS Console
SLT
EXT CardMPR Card
AnalogCO
KX-TDE
CO Card
OtherSIP Phone
SIPSoftphone
KX-NT KX-UTSLT
EXT Card SC CardSC Card
Direct Connectionlike TDE600 to TDE620
IP Network
KX-DT w/DSS Console
KX-NS1000
On the other hand, when customer has Panasonic PBX now, they can add IP capacity and IP functionality using KX-NS1000 version 2 with stacking card KX-NS0130 with keeping current PBX.This configuration is useful for new customer also whenthey need more SLT phone, Digital PT with DSS Console,Analog PT and analog CO as well as IP-Phone.
KX-NCS0130
KX-NS0130 SC card for NS100
KX-NS0131 SC card for NCP
KX-NS0132 SC card for TDA/TDE
100 % FeatureTransparencylike TDE600to TDE620
2. Introduction
4
3. Table of Contents
Chapter Explanation
1 Overview
2 Specifications
3 Concept of programming for Public mode
4 Step by step programming for the trunk adapter
5 Step by step programming for KX-NS1000
6 Programming hint for Private mode (QSIG)
7 Demonstration guide
5
Chapter 1Overview
6
One PRI by card Two PRI by card and adapter
Panasonic KX-NS8290 increases PRI capacity. KX-NS8188 for E1.
Activation key of IP Trunk is NOT required in KX-NS1000 to connectPRI / E1 trunk adapter, even if SIP Trunk of KX-NS1000 is used.
Trunk Adaptor
SIP Trunk (30-ch)
PRI30
SIP Extension
PanasonicKX-NS8290
PRI30
PRI Card
OtherSIP Phone
SIPSoftphone
KX-NT KX-UT
IP Network
KX-NS1000
PRI30
PRI Card
OtherSIP Phone
SIPSoftphone
KX-NT KX-UT
IP Network
KX-NS1000
11. Trunk Adapter for E1 / PRI
KX-NCS0290 KX-NCS0290
IP Trunk AK
7
Also useful to provide PRI/E1 with 2-ch Analog CO or 4 BRI.
Trunk Adaptor
SIP Trunk (30-ch)
PRI30E1
AnalogCO
Maximum 256 ch is available for E1 / PRI by adapter and IP trunk.
Trunk Adaptor
SIP Trunk(30-ch)
Max. 256ch can be registered to SIP provider or the adapter.
PRI30
PRI Card
Trunk Adaptor
SIP Trunk(30-ch)
PRI30E1SIP
Provider
CO Card
SIP Trunk(xx-ch)
12. Trunk Adapter for E1 / PRI - Capacity
256ch
PRI30E1
Line NS1000x 1
NS1000x 2
NS1000x 3
NS1000x 4 or more
Trunk 256 256 x 2 600
Legacy 256 256 x 2 600
IP incl E1/PRI adapter 256 256
SIP 256 256
H.323 48 48 x 2 = 96
8
More Analog CO by TDE (H.323)
KX-TDE with CO card increases CO capacity using H.323.
Activation key of IP Trunk is required in KX-NS1000 for H.323 all channels and required in KX-TDE for more than 4 or 16 channels.Activation key for “Enhanced QSIG” is not required because this configuration needs only basic QSIG function.
OtherSIP Phone
SIPSoftphone
KX-NT KX-UT
H.323
IP Network
CO Card
MPR Cardw/ VoIP DSP
13. TDE as Option by H.323
IP Trunk AK
IP Trunk AK
AnalogCO
KX-TDE
Reference
Stacking card isnot required in this case.
SC Card
EnhancedQSIG AK
EnhancedFeature AK
9
Trunk Adaptor
H.323 + SIP Trunk(256 ch)
PRI30
AnalogCO
AnalogCO
H.323(96 ch)
KX-NS1000
KX-TDE
CO Card
MPR Cardw/ VoIP DSP
HQ Branch
IP Network
KX-NCP
H.323(32 ch)
14. TDE as Option by H.323 - Capacity
Max. 96ch can be used for any other PBX. (Chanel is occupied only when call is made. )
Reference
Maximum 96 ch is available for Analog CO / BRI and H.323.
Line NS1000x 1
NS1000x 2
NS1000x 3
NS1000x 4 or more
Trunk 256 256 x 2 600
Legacy 256 256 x 2 600
IP incl E1/PRI adapter 256 256
SIP 256 256
H.323incl Analog CO by TDE
48 48 x 2 = 96
CO Card
CO Card
H.323(32 ch)
10
More Analog CO and DPT / SLT by Stacking Card
This configuration is useful if customer needs DPT with DSS Console and so on.- SC card for TDE-NCP is installed instead of MPR card.- SC card for NS1000 is installed to free slot. (Slot for “PRI+2SLT” etc )
Stacking Card increases DPT + SLT + Trunk capacity.
CO Card
OtherSIP Phone
SIPSoftphone
KX-NT KX-UTKX-DTSLT
EXT Card SC CardSC Card
Direct Connectionlike TDE600 to TDE620
IP Network
15. Stacking Card
KX-NS1000
AnalogCO
KX-TDE
100 % FeatureTransparency
like TDE600 to TDE620
Stacking Card
11
SpecificationsYou can connect a maximum of 2 existing PBXs for one KX-NS1000. A maximum of 8 existing PBXs and 16 KX-NS1000 can be connected for the entire One-look Network. An existing PBX refers to a Panasonic KX-TDE series, KX-NCP series, or KX-TDA100/200/600/620 PBX.
16-1. Stacking Card - Specifications
IP Network
KX-DT
KX-TDE600
KX-TDE620
KX-NCP
KX-DT KX-DT
IP Network
KX-DT
KX-TDE600 KX-TDE620
KX-NCP
KX-DT KX-DT
SC Card
SC Card
SC Card
SC CardSC Card
QSIG Max. 8 PBXs
Different PBX category cannot be mixed to one KX-NS1000. Category 1 : KX-NCP500-1000 Category 2 : KX-TDE(A)100-200 Category 3 : KX-TDE(A)600-620Stacking card for KX-TDA100D is not planned currently.
NCP500+TDE200 : N/ATDE100+TDA200 : OKTDE600+TDE620 : OKTDE620+TDE620 : OK
Stacking Card
12
Conditions- Cards in right table are not supported. Reason is as follows. - MPR is not required. - IP feature is supported by KX-NS1000. - DISA/SVM feature is supported by KX-NS1000 without AK. - New cards for TDE-NCP version 5 are N/A. - By above condition, KX-NT400 and KX-HGT100 cannot be used after connecting with KX-NS1000.- IP capacity AK is not required for trunk and extension in existing PBXs because these are not IP. - Other AK such as CA is required in KX-NS1000 for extension in existing PBX.- In case of TDA100/200 and TDE100/200 OPB3 card with ECHO16 must be installed in only Slot 1. *) Other cards except OPB3 or OPB3 card with other daughter board except ECHO16 can be installed to any slot.
16-2. Stacking Card - Conditions
Not Supported
Symbol Model
RMT TDA0196
MEC TDA0105/TDE0105
DSP4 NCP1104
DSP16 TDE0110
DSP64 TDE0111
CTI-LINK TDA0410
IP-EXT16 TDA0470
IP-GW4E TDA0484
IP-GW16 TDA0490
IP GW4 TDA0480
MSG4 TDA0191
ESVM2 TDA0192
ESVM4 TDA0194
CLCOT8 TDA1180
CLCOT8E TDA1186
MCSLC24 TDA1178
MCSLC16 TDA1176
Stacking Card
13
ProgrammingIt is not required to program for connection (Same as TDE600 to TDE620 connection). Property of cards in TDE/NCP can be programmed using NS1000 Web.
17. Stacking Card - Programming Stacking Card
14
18. Recommendation of Configuration
KX-NS1000 is recommended as follows, when new customer does not have Panasonic PBX now and they want to use IP phone mainly for extension.
When customer wants to useRecommendation
for Extension for Trunk
One PRI or 4 BRI Optional Card
E1 / 2 or more PRI
E1 / PRI + 4 BRITrunk Adapter
(+ Optional Card)
IP Phone + 2 SLT E1 / PRI + 2 Analog
3 or more Analog CO TDE/NCPas optionby H.323
5 or more BRI
Other mixture
IP Phone+ Digital PT+ Analog PT + SLT
(Any above configuration)TDE620
with Stacking Card
Version 2
Version 1 & 2
Version 1 & 2
Version 2
15
19. KX-NS1000 Capacity
Total capacity is as follows.
Line NS1000x 1
NS1000x 2
NS1000x 3
NS1000x 4 or more
Trunk 256 256 x 2 600
Legacyby stacking card or/and “xxx+SLT2” card
256 256 x 2 600
IP incl E1/PRI adapter 256 256
SIP 256 256
H.323 48 48 x 2 = 96
Extension 640 1000
Digital PT / Analog PT / SLTby stacking card or/and “xxx+SLT2” card
480 SLT (*1)512 DPT (*2)
1000
IP 640 1000
UT 640 1000
NT (NS1000 V1) 128 128 x 2 128 x 3 128 x N or 1000
NT (NS1000 V2) 256 256 x 2 256 x 3 1000
(*1) 24SLT x 10 by TDE620 x 2 for example(*2) 256 DPT incl DXDP by TDE620 x 2 for example
16
Chapter 2Specifications
17
Hardware Appearance is as follows.
21. Hardware Appearance
No. Description
1 System LED
2 E1 / PRI line LED
3 DC Jack
4 LAN Port
5 LAN LED (Link)
6 LAN LED (Transmission Speed)
7 E1 / PRI line port
8 Initialize button (Not slide switch)
Front
Back
Wall Mountain
Unpack the box and check the items below: Main Unit x 1 Screw x 2 Washer x 2
18
KX-NS8188 / KX-NS8290 supports PoE.
If PoE is not supported by network, AC adapter is required. KX-A420 for Brazil KX-A239 for others
*) These are same model of AC adapter for KX-UT phone.
22. PoE (Power over Ethernet)
19
KX-NS8188 E1 adapter supports following features.
23. KX-NS8188 E1 Adapter
Features NS8188 TDA0188(Reference)
Signaling DR2 Yes Yes
E&M-C No Yes
E&M-P No Yes
Dial Type MFC-R2 Yes Yes
DTMF Yes Yes
Pulse No Yes
Caller Number Notification (ANI) Yes Yes
Charge / Meter Pulse No Yes
Deny collect call for Brazil Yes Yes
Outgoing call auto disconnect Yes Yes
KX-TDE
KX-TDA0188
Trunk Adaptor
KX-NS8188
E1
KX-NS1000
20
KX-NS8290 PRI adapter supports following features.
24. KX-NS8290 PRI Adapter
Features NS8290 NS0290(Reference)
Mode
CO (Public) Yes Yes
Extension No Yes
QSIG-master/slave (Private) Yes Yes
ISDNCarrier Service(Public)
CLIP / CLIR Yes Yes
COLP / COLR No Yes
CNIP /CNIR Yes Yes
CONP / CONR No Yes
Advice of charge Yes Yes
Call Forwarding No Yes
Call Hold No Yes
Call Transfer (incl. ISDN Centrex) No Yes
Tree-party conference No Yes
Malicious call identification No Yes
Generic keypad protocol No Yes
CCBS No Yes
ISDN - Virtual Private Network No Yes
E-911 (for PRI23) Yes Yes
Trunk Adaptor
KX-NS8290
KX-NS0290
PRI Card
ISDN
“No” because these services by ISDN provider are not popularand PBX can support same feature basically.
Confby
PBX
Confby
ISDN
KX-NS1000
21
25. KX-NS8290 PRI Adapter for QSIG
Trunk Adaptor
PRI QSIG
H.323 QSIG
Private Network
(Leased ISDN)
30ch or 23ch
NS1000 or other PBX
PRI QSIG
H.323 is used for this configuration instead of SIP.
KX-NS8290 PRI adapter supports QSIG also.Features NS8290 TDA0290
(Reference)
QSIG service
CLIP/CLIR Yes Yes
CNIP/CNIR Yes Yes
Call Forwarding (CF) Yes Yes
Call Transfer (CT) Yes Yes
Completion of Calls to Busy Subscriber (CCBS)
Yes Yes
Network Direct Station Selection (NDSS)
Yes Yes
Centralized Voice Mail Yes Yes
Network ICD Group Yes Yes
KX-NS1000
Line NS1000x 1
NS1000x 2
NS1000x 3
NS1000x 4 or more
IP incl E1/PRI adapter 256 256
SIP + PRI Adapter for Public 256 256
H.323 + PRI Adapter for QSIG 48 48 x 2 = 96
IP Trunk AK
22
Fractional service is also available.<Stand alone>
26. Fractional Service
20ch
Trunk Adaptor
KX-NS1000
1st KX-NS1000in Fukuoka
20ch
20chE1/PRI
Trunk Adaptor
30ch
Trunk Adaptor
10ch
Trunk Adaptor
Total 256ch
<One-look network>
2nd KX-NS1000in Tokyo
16th KX-NS1000in Niseko
30ch
Trunk Adaptor
60chE1/PRI
10chE1/PRI
20chE1/PRI
23
Back-up is available automatically for SIP trunk incl E1 / PRIadapter, KX-NT/UT IP-phone and one look connection.
SIP Trunk
PRI/E1 or SIP ProviderTrunk Adaptor
KX-NS1000 (1st)Master
KX-NS1000 (2nd)Back-up Master
KX-NT KX-UT
Trunk Adaptor
KX-NS1000Master
KX-NS1000Back-up Master
KX-NT KX-UT
After master PBX stops working,
SIP Trunk
One-Look AK One-Look AK
Back-up master PBX works as slave PBX usually.But it works as master PBX after master PBX stops working.
KX-NT KX-UT
KX-NT KX-UT
One-Look AK One-Look AK
PRI/E1 or SIP Provider
27. Solution with “Back-up Master”
24
Chapter 3Concept of Programming
for Public Connection
25
31. Concept of Programming - Adapter
The trunk adapter is PBX with E1 / PRI trunk and SIP extension.SIP trunk of KX-NS1000 is registered to SIP extension of the adapter.
<Programming for the trunk adapter>Software of the adapter is basically same as KX-NS1000. Features except E1 / PRI and SIP extension are removed. Therefore programming method is very similar to KX-NS1000.
Trunk Adaptor
E1 / PRI
SIP Extension401-430
PRI
KX-NS1000
30ch or 23ch
KX-NS0290
- PRI configuration is same as programming for KX-NS1000 PRI card (KX-NS0290). E1 configuration is same as KX-TDE E1 card (KX-TDA0188).
- SIP extension configuration is same as KX-NS1000. But SIP extension is programmed by default. 401 to 430 for E1 / PRI30 401 to 423 for PRI23
PRI Card
ID 401-430SIP Trunk
KX-TDE
KX-TDA0188
E1/ ISDN
26
32. Concept of Programming – NS1000
<Programming for KX-NS1000>The trunk adapter is basically SIP provider for KX-NS1000.Following has to be programmed.- IP address of the adapter as SIP server destination - SIP registration User ID (Password is not required.)- Connection Attribute : SIP Provider / Trunk Adapter
Trunk Adaptor
SIP Extension401-430
KX-NS1000
30ch or 23ch
E1/ ISDN
E1 / PRI
ID 401-430SIP Trunk
27
401 402 430
33. Concept of Programming - Call
<Programming for KX-NS1000 - CONT>Programming of the trunk adapter is not required for DDI / DIL incoming call from E1/PRI to SIP extension. It works like DIL 1:1 without programming and DDInumber and caller ID are informed from the trunk adapter to KX-NS1000. Programming of KX-NS1000 is required for DDI / DIL.Outgoing call is also programmed forKX-NS1000 instead of the trunk adapter.
Therefore administrator has to access only KX-NS1000 to change extension number, DDI and so on after dealer installed.
SIP Extension
KX-NS1000
E1 / ISDN
SIP Trunk
CH1 CH2 CH30
Trunk Adapter
E1 / PRI
DDICaller ID
28
Chapter 4Step by Step Programming
for Trunk Adapter
Trunk Adaptor
KX-NS1000
29
Operation and “SYSTEM” LED display is as follows.1. Power On (Connect AC adapter or connect LAN with PoE) (a) Amber On (5 sec) (b) Amber rapid flash (5 sec)2. During (b), keep pressing Initialize button for 1s. (c) Off (2 sec) (d) Amber On (30 sec) (e) Amber slow flash (120 sec) (f) Green slow flash
- Display of (b) finishes before 5 sec after operation of (2).- Display of (f) means success of initialization and awaiting “Easy set-up” of web maintenance console.
41. Initialize
Initialize ButtonSystem LED
Trunk Adaptor
KX-NS1000
30
LED indication is as follows.
42. LED Indication
Trunk Adaptor
KX-NS1000
31
(1) Set IP address 192.168.0.99 for example to your PC like first connection of KX-TDE or KX-NCP. - Trunk adapter does not have maintenance port with DHCP server. - Sub-net mask should be 255.255.255.0 (2) Connect 192.168.0.151 by Firefox. - Default IP address of trunk adapter is 192.168.0.151.
43. PC Connection - 1
192.168.0.151by default
192.168.0.99for example
Trunk Adapter
KX-NS1000
192.168.0.101by default
DHCP Server
For demo, NS1000 with DHCP server function is useful to assign IP address of PC automatically.
Trunk Adaptor
KX-NS1000
32
(1) In 10 seconds from step in previous page, log-in menu is displayed.(2) Input “INSTALLER” as user and “1234” as password.
43. PC Connection - 2
Trunk Adaptor
KX-NS1000
33
44. Easy setup - Language selection
(1) Select language.Trunk Adaptor
KX-NS1000
34
44. Easy setup - 1
(1) Select Suffix of KX-NS1000 and area.
If Suffix is changed, system restarts again after click [OK].Wait 3 min and connect PC again.
No need to change
(a) Amber slow flash (30 sec)(b) Amber On (10 sec)(c) Amber rapid flash (5 sec)(d) Amber On (30 sec)(e) Amber slow flash (120 sec)(f) Green slow flash
Trunk Adaptor
KX-NS1000
35
44. Easy setup - 2
No need to change.- Adapter name is only for reference.- Time is used only for error log.
Trunk Adaptor
KX-NS1000
36
44. Easy setup - 3
(1) Input IP address of trunk adapter in actual customer’s network. Get the IP address from IT manager.*) For demo, default is OK.
Trunk Adaptor
KX-NS1000
37
44. Easy setup - 4
No need to change.- Time is used only for error log. Trunk Adaptor
KX-NS1000
38
44. Easy setup - 5
(1) Input password as you hope, click [Finish].(2) Wait for 30 seconds.
If LAN setting is changed, system restarts again after click [OK].Wait 3 min and connect PC again.
(a) Amber slow flash (30 sec)(b) Amber On (10 sec)(c) Amber rapid flash (5 sec)(d) Amber On (30 sec)(e) Amber slow flash (120 sec)(f) Green slow flash
Trunk Adaptor
KX-NS1000
39
45. Maintenance Console - Top menu
If LAN setting is changed, (1) Remove the trunk adapter from LAN(2) Connect it to actual customer’s network.(3) Connect PC to IP address of trunk adapter using Firefox.(4) After log-in, following top menu is displayed.
If LAN setting is not changed, following Top menu is displayed.
Trunk Adaptor
KX-NS1000
40
45. Maintenance Console - 1
Software version can be confirmed as follows.Trunk Adaptor
KX-NS1000
41
45. Maintenance Console - 2
Parameter for PRI can be modified as follows.(Same as “PRI + 2 SLT” card) Trunk Adaptor
KX-NS1000
42
45. Maintenance Console - 3
IP address of adapter can be changed.(No need to change usually.) Trunk Adaptor
KX-NS1000
43
45. Maintenance Console - 4
Software can be updated by one step. (Not same as KX-NS1000)
- Wait 15 minutes after clicking [Execute]. (Same as KX-NS1000.)
Trunk Adaptor
KX-NS1000
44
45. Maintenance Console - 5
E1/ PRI Card diagnosis is supported.
Out of service can be assigned.This is required for software update also.
Trunk Adaptor
KX-NS1000
45
Chapter 5Step by Step Programming
for KX-NS1000
46
51. KX-NS1000 - Out of Service
Install virtual SIP trunk card.Out of service is required for port or card beforeprogramming in following pages.
Trunk Adaptor
KX-NS1000
Trunk Adaptor
47
52. KX-NS1000 - Connection Attribute
Change connection attribute from “SIP provider”to “Trunk Adapter” for each channels or click[Trunk Adapter] button to change max. 30 ch at the same time.
Trunk Adaptor
KX-NS1000
Trunk Adaptor
Use this. No need to program each ch.
48
Max. 16 Adapter*) If program manually not using “trunk adapter”, more than 16 adapter
can be programmed.
53. KX-NS1000 - Trunk Adapter button - 1
Input IP address of trunk adapter and click [Next].- Trunk adapter name is for reference.
Web maintenance console for the trunk adapter is opened.
For reference
Trunk Adaptor
KX-NS1000
Trunk Adaptor
192.168.0.151 192.168.0.152
49
Select range to connect the trunkadapter instead of SIP provider.Select IP address and click [Finish].
If fractional service is used, set “20” for example. Otherwise NS1000 tries making call using 21ch to 30ch of PRI.
Trunk Adaptor
KX-NS1000
Trunk AdaptorSIP
Provider
192.168.0.151 192.168.0.152
54. KX-NS1000 - Trunk Adapter button - 2
50
55. KX-NS1000 - Registration to SIP Server
Connection attribute were programmed by previous step. Parameters for registration to SIP server (E1/PRI adapter) were also programmed.
Trunk Adaptor
KX-NS1000
Trunk Adaptor
192.168.0.151 192.168.0.152
51
56. KX-NS1000 - CLIP
“PBX CLIP” has to be selected as follows to send CLIP on extension for outgoing call. Trunk Adaptor
KX-NS1000
Trunk Adaptor
52
57. KX-NS1000 - In Service
Set In Service. - Other programming such as ARS, TRS is basically same as PRI for KX-TDE/NCP.- However it is required to program as next 2 pages additionally because I/F with trunk adapter is SIP.
When E1/PRI line of trunk adapter is fault, trunk adapter stops communication with KX-NS1000. Therefore the SIP trunk ch of KX-NS1000 becomes fault.This specification is useful not to use the SIP ch automatically for ARS and so on.
Trunk AdaptorE1 /
ISDN
KX-NS1000
53
58. KX-NS1000 - Dialing Plan
Dialing plan has to be programmed for outgoing callbecause I/F with trunk adapter is SIP en-block dial.Otherwise extension caller has to wait for 10 secondsto hear ring back tone after dial to E1/PRI trunk adapter.
Trunk Adaptor
KX-NS1000
Trunk Adaptor
54
59. KX-NS1000 - DDI Modification
DDI first 3 digits has to be removed because I/F with trunk adapter is SIP. ID such as “401” + real DDI number is informed as DDI number from E1/PRI adapter to KX-NS1000.
Trunk AdaptorE1 / ISDN
KX-NS1000DDI 5678 DDI 4015678
DDI 5678 Program DDI table.
55
Chapter 6Programming Hint forPrivate Mode (QSIG)
56
Trunk Adaptor
61. Easy Setup for Adapter
“Private” has to be selected by easy setup mode.
KX-NS1000
Ext 1xx
Ext 2xx192.168.0.101 192.168.0.151
ISDN QSIGH.323
57
Trunk Adaptor
62. PRI QSIG mode for Adapter
QSIG (Slave) is assigned automatically after easy setup.
KX-NS1000
Ext 1xx
Ext 2xx192.168.0.101 192.168.0.151
ISDN QSIGH.323
58
192.168.0.101
Trunk Adaptor
63. H.323 programming for Adapter
H.323 destination programming of adapter is also required. Common IP address is assigned for any dial. (Not each dial)
KX-NS1000
Ext 1xx
Ext 2xx192.168.0.101 192.168.0.151
ISDN QSIGH.323
IP address of Back-up master PBX
59
Trunk Adaptor
64. H.323 programming for KX-NS1000
H.323 destination programming of KX-NS1000 is required for adapter as well as other PBXs.Sole difference is that activation key for IP trunk is not required.
IP Network
KX-NS1000
Ext 1xx
Ext 2xx
Ext 3xx
Ext 4xx
192.168.0.101 192.168.0.151
192.168.30.101
192.168.40.101
ISDN QSIG
DN2IP table (Dial to IP)----------------------------------- Dial 2xx to 192.168.0.151Dial 3xx to 192.168.30.101Dial 4xx to 192.168.40.101
H.323
60
Chapter 7Demonstration Guide
61
71. Configuration Example
PRI Adaptor
SIP Trunk (30-ch)
Ext 101CLIP 01234311
KX-NS1000
Ext 102CLIP 01234312
PRI
Ext 201CLIP 01234321
KX-NCP with PRI
KX-TDEwith 2 PRI Extensionas ISDN provider P
RI
PRI
Ext 301 Ext 31X Ext 32X(for test)
DLC
62
Dial 321(Remove 01234 by ARS)
72. Outgoing Call
PRI Adaptor
SIP Trunk (30-ch)
Ext 101CLIP 01234311
KX-NS1000
Ext 102CLIP 01234312
PRI
Ext 201CLIP 01234321
KX-NCP with PRI
KX-TDEwith 2 PRI Extensionas ISDN provider P
RI
PRI
Ext 301 Ext 31X Ext 32X(for test)
DLC
DDI 321
01234311
Dial 321
Dial 0/9-01-234-321
Dialing plan 3XX
DDIProgram
63
Dial 312(Remove 01234 by ARS)
73. Incoming Call
PRI Adaptor
SIP Trunk (30-ch)
Ext 101CLIP 01234311
KX-NS1000
Ext 102CLIP 01234312
PRI
Ext 201CLIP 01234321
KX-NCP with PRI
KX-TDEwith 2 PRI Extensionas ISDN provider P
RI
PRI
Ext 301 Ext 31X Ext 32X(for test)
DLC
DDI 312
DDI 401312
01234321 Dial 0/9-01-234-312
DDIProgram
64
Ext 301 Ext 31X Ext 32X(for test)
74. PRI Extension
PRI Adaptor PRI
PRI
PRI
DLC
Standard LAN cable can be used by this switch for PRI Extension.
65
75. KX-NS1000 – SIP Register Resending
“Register Resending Interval” has to be 10 seconds.If default value 300 seconds is used, it takesfor 0 to 300 seconds to reconnect KX-NS1000 and trunk adapter, when trunk adapter returns IN Service from Out of Service or LAN is reconnected.
Trunk Adaptor
KX-NS1000
Trunk Adaptor
66
Thank you !The END