Model ISC40Inductive Conductivity sensor and fittings
GS 12D8J2-E-E9th Edition
The model ISC40 sensors are designed for use with theEXA: ISC200 2-wire transmitters and the EXA: ISC402 4-wire analyzers. This combination exceeds all expectations for conductivity measurement in terms of: reliability, accuracy, rangeability and price performance.
The accuracy is 0.5% of reading plus 0.5 uS/cm for any conductivity value: whether measured in rinse water or inconcentrated acids. The materials of construction guarantee along life under harch industrial conditions:- The erosion/abrasion resistant PEEK (Poly Ether Ether Ketone),
which also features excellent chemical resistance in all solutionsexcept fluoric acid or oxidizing concentrated acids.
- The ultimate material in terms of chemical resistance: PFA forapplications in hydrofluoric acid and oxidizing concentratedacids (nitric, sulfuric, oleum).
The PEEK sensor is provided with a rugged Stainless Steelmounting thread/nut/ gasket combination for ultimate flexibility ininstallation using bulk head installation technique. There is also awide range of holders and options available for reliable in-line oroff-line installation with double O-ring seals for long service life ofthe sensor. Additional models are available for use in Ball-ValveInsertion applications and in Sanitary Flange installations.
The PFA sensor comes with an integral lap-joint flange, becausein applications, where this sensor is used, it is very difficult to findO-rings that are resistant to the process.
Both sensors have a large bore for optimal resistance to foulingprocesses and when properly installed, the flow will keep the sensor clean preventing measuring errors.
GeneralSpecifications
System Configuration
Sensors Cables Fittings Transmitters AccessoriesSensors Fittings
Features and Applications• Inductive Conductivity technique for elimination of fouling and
polarization errors.• Wide bore sensors for long term stability.• Installation flexibility by wide range of holders and by the use of
universal bulkhead construction.• Wide rangeability in terms of conductivity (1 µS/cm to 2 S/cm)
and temperature (-20 to 130ºC).• All applications where severe electrode fouling prevents the use
of contacting electrodes.• All ranges except the (ultra) pure water applications.• All slurry applications where conventional systems suffer from
plugging or erosion.• All applications where the 6 decade rangeability is necessary
for accurate process control.
Ø 40 ( 1.57)
wrench opening 20 ( 0.79 )
wrench opening 32 ( 1.42 )
thermistor
ground
secondary
primary
YOKOGAWA
G3/4
47(1.85)
11121713151614
L= 5000 ( 200 )
ca 2
40 (
9.45
)
40 (
1.57
)10
0 (3
.94)
Hole in flangeØ 27 mm (1.06")
D
d
I
t
d = distance min 25 mm (1")D = access port size min 50 mm (2")
Dimensions
Note: The ISC40 was previously supplied with a flat viton gasketfor simple mounting. The fittings have been improved bythe addition of “O”- ring seals which replace the flat gasket. We continue to supply the flat gasket with theISC40G(S) -PG.. sensors for compatibility with existinginstallations. When using the sensor in combination withthe new fittings, the flat gasket should be discarded.
2
GS 12D8J2-E-E
General SpecificationsModel ISC40 Inductive conductivity sensorA. Compatibility : ISC40G is suitable for use with both
ISC402G and I(S)C200G inductiveconductivity transmitter.
B. Hazardous area : ISC40S is suitable for use with theI(S)C200S conform to ATEX, FMand CSA intrinsic safety standards
- ATEX intrinsic safety : II 1 G EEx ib [ia] IIC T6 for ambient temp. -10 to 40°C
: II 1 G EEx ia [ia] IIC T4 for ambient temp. -10 to 55°C
- ATEX certificate no. : KEMA 00 ATEX 1067 X- FM intrinsic safety : IS CL1, DIV1, GP ABCD T3B
for ambient temp. (ta) -10°C to 55°C and T4 for ambienttemp. (ta) -10°C to 40°C.
- FM approval report : J.L. 1Y1A7.AX- CSA intrinsic safety : Ex [ia] Class I, Division 1, Groups C
and D, T4a- CSA approval file : LR 102851-1
C. Measuring range : 0- 2000 mS/cm at actual processtemperatures. The sensor has anerror of 0.5 µS/cm (PEEK sensors)or 1 µS/cm (PFA sensor) that mustbe considered when applicationrange is chosen.
D. Installation factor : Cellconstant: The nominal cell constant of the sensor is 1.88/cmfor the PEEK sensor types and3.00/cm for the PFA sensor. Thecalibrated values are indicated onthe cable markers and the actualinstallation can change this factor. Ifthere is less than 25 mm spacingbetween sensor and holder, in-situcalibration is necessary to meet thespecified accuracies. An indicationis given in fig. 2
E. Process temperature range Peek : -20 to 130 °C (0 to 270 °F) for
Response time 5 min. (90%)PFA : -20 to 100 °C (0 to 212 °F)
Response time 10 min. (90%)
F. Process pressurePeek : Maximum 20 bar (300 psi)
dependant on installation.PFA :
G. Materials- Sensor wetted parts : Victrex PEEK
(Poly-Ether-Ether-Ketone) : PFA.
(High purity Perfluoro alkoxy alkane)- Sealing gasket : Viton for PEEK
: Gore tex for PFA- Process adapters : AISI 316 SS, PVC or PVDF
(only for PEEK)
H. Process connection : Process connection are made incombination with a variety ofadapters and fittings. See relevantsections in this document.
I Cables- Connection cable : Integral connection cable in a
variety of lengths up to 20 meter.- Extension cable : Extension cable with WF10 junction
box BA10 can be used to a total of 50 metres (fixed cable and extension cable).
J. Shipping details- Package
- 3-5 meters : WxHxD = 350x270x50 mm- 10-20 meters : WxHxD = 320x240x110 mm
- Packed weight approx.- 03 m : 1.0 kg- 05 m : 1.3 kg- 10 m : 1.6 kg- 15 m : 2.1 kg- 20 m : 2.5 kg- protection hose : 0.8 kg (approx.)
°C (°F) 100 (212) 20 (36)
BAR (PSI) 5 (71) 10 (142)
FIG. 1.
D2
D1
FLANGE ADAPTERd
116
(4.5
6)
O-ring
26.57 x 3.53
40.64 x 5.33
3
GS 12D8J2-E-E
FIG. 2. Actual installed cell-constant as function ofspacing around the sensor.
D
non conductivepiping
conductivepiping
D i n m i l l i m e t e r s
0 10 20 30 40 50
0.90
Cor
rect
ion
fact
or (
x no
min
al C
.C.)
0.95
1.30
1.25
1.20
1.00
1,05
1.10
1.15
Only for PEEK
Flange adapter for -PG sensor
Flange Adapters for -PG sensor
H
D
THREAD ADAPTER
116
(4.5
6)
O-ring
26.57 x 3.53
40.64 x 5.33
Screw-in for -PG sensor
Thread D H Material/FSJ R2 75 (3) 48 1.9) PVDF/PSG R2 75 (3) 42 (1.7) PVC/SSG R2 64 (2.5) 39 (1.5) SS
d D1 D2 Material/FFJ5 Ø 19 (0.75) 120 (4.70) 155 6.1) PVDF/PFJ Ø 19 (0.75) 120 (4.70) 155 (6.1) PVC/SFA Ø 19 (0.75) 121 (4.75) 152 (6.0) SS/SFD Ø 18 (0.71) 125 (5.00) 165 (6.5) SS/SFJ Ø 19 (0.75) 120 (4.70) 155 (6.1) SS
Note: ISO7/1 - R2 = 2” BSPT
DIMENSIONS mm (inches)
DIMENSIONS mm (inches)
Model and Suffix Codes
Model Suffix Option DescriptionISC40G-GG General purpose, glass filled PEEK,
general modelISC40G-GR General purpose, glass filled PEEK,
retractable modelISC40G-GS General purpose, glass filled PEEK,
shaft modelISC40G-TF General purpose, PFA, flange
modelISC40S-GG Intrinsically safe glass filled PEEK,
general modelISC40S-GR Intrinsically safe, glass filled PEEK,
retractable modelISC40S-GS Intrinsically safe, glass filled PEEK,
shaft modelISC40S-TF Intrinsically safe, PFA, flange modelTemp. -T1 Pt1000sensor -T3 30K thermistor
Note: For IC200 select only T3Cable -03 03 mtrlength -05 05 mtr
-10 10 mtr-15 15 mtr-20 20 mtr
Material Proc. Conn.Flange adapters /FFJ5 PVDF JIS 10K-50-RFfor -GG sensor /PFJ PVC JIS 10K-50-RF
/SFA AISI316 SS 2” ANSI 150 lbs/SFD AISI316 SS NW50-PN16/SFJ AISI316 SS JIS 10K-50-RF
Screw-in adapter /PSG PVC ISO 7/1-R2for -GG sensor /FSJ PVDF ISO 7/1-R2
/SSG AISI316 SS ISO 7/1-R2Flange adapters /SFT1 AISI316 SS Sanitary Tuchenhagenfor -GS sensor /STC1 AISI316 SS Sanitary 2” tri-clamp
/STC2 AISI316 SS Tri-clamp completeProtection hose /PHoo 03m, 05m, 10m, 15m, 20mfor -TF sensor (the same length as the cable)Certificates /M Material certificate (only apply to
SS316 wetted part)/Q Quality certificate
For mountingin SFT, STC 1 andSTC 2 Fittings.
Ø20 (0.78")
193
(7.6
0")
77 (
3.0"
)
Stainless steel
Peek
Minimum holeto fit sensorthrough: Ø48 (1.89")
Ø47 (1.85")
4
GS 12D8J2-E-E
nut G3/4
viton gasket
Ø40 (1.57")
182
(7.1
6")
124
(4.8
8")
Minimum holeto fit sensorthrough: Ø48 (1.89")
Ø47 (1.85")
ISC40-PG
For mounting inISC40PRretractable fitting
Minimum holeto fit sensorthrough: fl48 (1.89")
fl47 (1.85")
45 (1.77")
ISC40-PS
Unit: mm (inches)
Dimensions of Sensors
ISC40-PR
124.
5 (4
.9")
56 (2
.2")
Ø 1
00 (
3.94
)
189.
5 (7
.46"
)
Ø 6
1 (2
.4)
G 3/4"
Ø50 (1.97")
Minimum holeto fit sensorthrough: Ø50 (1.97")
ISC40-TF Unit: mm (inches)
Unit: mm (inches)
Unit: mm (inches)
Option Description Material Process connection Part number/FFJ5 Flange adapter PVDF JIS 10K-50-RF K1541ZC/PFJ Flange adapter PVC JIS 10K-50-RF K1541ZB/SFA Flange adapter AISI316 SS 2” ANSI 150 lbs K1541ZR/SFD Flange adapter AISI316 SS NW50-PN16 K1541ZQ/SFJ Flange adapter AISI316 SS JIS 10K-50-RF K1541ZE/FSJ Screw-in adapter PVDF ISO 7/1-R2 K1541ZD/PSG Screw-in adapter PVC ISO 7/1-R2 K1541ZN/SSG Screw-in adapter AISI316 SS ISO 7/1-R2 K1541ZL
/SFT Flange adapter AISI316 SS Sanitary Tuchenhagen K1541ZP/STC1 Flange adapter AISI316 SS Sanitary 2” tri-clamp K1541ZG/STC2 Flange adapter AISI316 SS Tri-clamp complete K1541ZF
All adapters include Viton O-rings/PH03 03 meter protection hose K1500DN/PH05 05 meter protection hose K1500DP/PH10 10 meter protection hose K1500DQ/PH15 15 meter protection hose K1500DR/PH20 20 meter protection hose K1500DS
5
GS 12D8J2-E-E
123
(4.8
4")
Ø71 (2.80")
19 (0.75")
72 (
2.83
")
2" tri-clamp
57,3
(2.
25")
134,
3 (5
.30"
)
Tri-clamp completeTuchenhagen Sanitary 2” tri-clamp
Options for the ISC40-PS (/SFT, /STC1, /STC2)
O-ring18.72 x 2.62
O-ring18.72 x 2.62
O-ring18.72 x 2.622” clamp seal
Options for -PS Sensor
Unit: mm (inches)
O-ring60 x 3
AccessoriesO-rings spare parts for ISC40 sensor & Options as spare parts
O-ring materialDimensions EPDM Viton Silicon KALREZ QuantityO-rings for option FFJ5 /FSJ /PFJ /PSG /SFA SFD /SFJ /SSG /40.64 x 5.33 / 26.57 x 3. 53 K1500CA K1500CB K1500CC 5 sets of 2 O-rings40.64 x 5.33 K1500CD 1 O-ring26.57 x 3. 53 K1500CH 1 O-ringO-rings for option /SFT18.72 x 2.62 / 60 x 3 K1500CM K1500CL K1500CN 5 sets of 2 O-ringsO-ring for option /STC118.72 x 2.62 K1500CQ K1500CP K1500CR 5 O-ringsO-rings for option /STC218.72 x 2.62 / 2” clamp seal K1500CT K1500CS K1500CU 5 sets of 2 O- ringsO-rings for protection hose25.9 x 3.53 / 23.52 x 1.78 K1500DT 5 sets of 2 O- ringsO-rings for old modelsViton gasket K1500AM 5 O-rings
/SFT /STC1 /STC2
123
(4.8
4”)
ø71 (2.80”)
19 (7.48”)
72 (2
.83”
)
134.
3 (5
.30”
)57
.3 (2
.25”
)Spare parts ISC40G(S)
Part no. DescriptionK1500AL 3 mounting nuts G
3/4,ISC40G/SK1500AW Flexible conduit, 5 meterK1500AX Flexible conduit, 10 meterK1500AY Connection parts for conduitK1500BP Clamp seal ring 2" EPDM
6
GS 12D8J2-E-E
Fittings for ISC40G(S)-PGInductive Conductivity Sensors
For liquid analysis, the sensors are frequently mounted in either aflow or an immersion fitting. Yokogawa suppllies for the modelISC40 inductive conductivity sensors a full range of fittings withparticular emphasis on designs that reduce installation and main-tenance time and consequently save operation costs.
A wide choice of construction materials gives the user the opti-mal solution for any process considering chemical resistance,pressure and temperature specifications.
The flow fittings are used for installation of the sensors in sampleby-pass lines. This makes maintenance easy without having tointerrupt the main process stream. The subassemblies simplifiesmounting of the sensors direct into process lines or vessels.This is particularly important where sample lines give problems,for instance with settling slurries.
Features• Wide choice of construction materials.• Built in drain on stainless steel flow fitting.• Quick disconnect direct insertion sub assemblies.• High temperature PVC immersion fitting with optional flanged
process connection for adjustable insertion depth.• High pressure and temperature specifications.• Electrolytically polished stainless steel fittings for optimal corro-
sion resistance.
Ø 100 (4.0)
1/2
NP
T (
150)
97 (
3.9)
39 (
1.6)
120 (4.8)
1/2 NPT (150)
1/2 NPT (150)
Ø 54 (2.2) 1/2 NPT (150)
1/2 NPT (150)
100 (4.0)
158
(6.3
)
70 (2.8)
70 (2
.8)
186
(7.3
)
ø90(3.54)
[72(2.83)]27(1.06)
127
(5)
D1D2
d
Hole pattern for mounting set (Option /MS or /MP)
Unit: mm (inches)
1. Model ISC40fF Flow fittingA. Process temperature
- Model ISC40FF-S : Maximum 150 °C (300 °F)- Model ISC40FF-P : Maximum 100 °C (210 °F)- Model ISC40FF-F : Maximum 130 °C (270 °F)
B. Process pressure- Model ISC40FF-S : Max. 1.0 MPa (150 psi) at 150 °C (300 °F)- Model ISC40FF-P : Max. 0.6 MPa (90 psi) at 20°C (70°F)
Max. 0.1 MPa (15 psi) at 100°C (210°F)- Model ISC40 FF-F : Max. 1.0 MPa (150 psi) at 20°C (70°F)
Max. 0.1 MPa (15 psi) at 120°C (250°F)C. Wetted materials
- Model ISC40FF-S : AISI 316 Stainless Steel- Model ISC40FF-P : Polypropylene- Model ISC40FF-F : PVDF (KYNAR®)Non-wetted materials- Nut : AISI 304 stainless steel.- Mounting set : AISI 304 Stainless Steel (optional)- Flange adapters : AISI 304 Stainless Steel (optional)
Dimensions
DIMENSIONS mm (inches)d D1 D2 Material
/FS2 Ø 14 (0.55) 85 3.3) 115 (4.5) SS/FP2 Ø 14 (0.55) 85 (3.3) 115 (4.5) PP/FF2 Ø 14 (0.55) 85 (3.3) 115 (4.5) PVDF/FSJ2 Ø 19 (0.75) 90 (3.5) 125 (4.9) SS/FPJ2 Ø 19 (0.75) 90 (3.5) 125 (4.9) PP/FFJ2 Ø 19 (0.75) 90 (3.5) 125 (4.9) PVDF
ISC40FF-PISC40FF-F
ISC40FF-S
7
GS 12D8J2-E-E
Model Suffix Option Descriptioncode code codeISC40FF flow fittingMaterial -S AISI 316 stainless steel
-P Polypropylene (PP)-F PVDF (KYNAR®)
Process -A NPTconnection -J ISO 7/1 R1/2"NPT Flange /FF1 PVDF, DN15 PN10adapters /FF2 PVDF, DN25 PN10
/FF3 PVDF, ANSI 1/2"-150lbs/FF4 PVDF, ANSI 1"-150lbs/FP1 PP, DN15 PN10/FP2 PP, DN25 PN10/FP3 PP, ANSI 1/2"-150lbs/FP4 PP, ANSI 1"-150lbs/FS1 AISI 316 SS, DN15 PN10/FS2 AISI 316 SS, DN25 PN10/FS3 AISI 316 SS, ANSI 1/2"- 150lbs/FS4 AISI 316 SS, ANSI 1"- 150lbs
ISO 7/1 R Flange /FFJ1 PVDF, JIS 10K-15-RFadapters /FFJ2 PVDF, JIS 10K-25-RF
/FPJ1 PP, JIS 10K-15-RF/FPJ2 PP, JIS 10K-25-RF/FSJ1 AISI 316 SS, JIS 10K-15-RF/FSJ2 AISI 316 SS, JIS 10K-25-RF
Mounting set /MS Wall/pipe for SS flow fitting/MP Wall/pipe for PP or PVDF flow fitting
Mat. certificate /M 3.1.B acc. EN-10-024 (DIN 50-049-3.1B)
Model and Suffix Codes
Partnumber FLANGES DescriptionK1500HG DN80 PN10 T-Piece, DN80 FlangeK1500HF DN100 PN10 T-Piece, DN100 FlangeK1500HP DN65 Gore-Tex seal for ISC40-TF (DN50)
T-Piece for ISC40-TF, Ind. Cond. SensorK1500HF, K1500HG.
Unit: mm (inches)
DN65 PN10
300.0
Innerside of T-piece islined with PFAThickness: 4mm
100.
0
DN
80 P
N10
/ D
N10
0 P
N10
Packaging size : 325 x 240 x 250weight : 19.23 kg
ø B ø A
C
A B CDN65 PN10 185 145 4 ø18DN80 PN10 200 160 8 ø18DN100 PN10 220 180 8 ø18
Mounting flange and bolts are included
2. Model ISC40FD Immersion fittingA. Process temperature : Max. 80 ºC (180 ºF) PVC
: Max. 150 ºC (300 ºF) AISI 316 Stainless steel
B. Process pressure- PVC : Max. 0.2 MPa (30 PSI) at
20ºC (70ºF)Max. 0.1 MPa (15 PSI) at 80ºC (180ºF)
- AISI316 Stainless steel : 10 barC. Wetted materials
- Probe tube : C-PVC- Process sealing O-ring : Viton- Flange : PVC (Optional) Non wetted materials- Cable insulation : Thermoplastic rubber
D. Process connection : - Adjustable flange : Hole pattern according to DIN
DN50-PN10 and ANSI 2” 150 lbs.Only for the PVC (Optional).
- Mounting set : Galvanized steel (Optional).
Note: Adjustable flange (/FA) is only for the PVC fitting
Dimensions
Immersion fitting
ø50 (2.0)
114(4.49)
Pipe &Sensorlength
LPipe &sensorlenght
L
Model and Suffix Codes
2" Handrail
Guide pipeØ 48.6 x 500(Ø 1.9 x 20")
Min: 110 (4.35")Max: 415 (16.34")
Immersion fitting
Ø 60 (2.36")
L
Ø 50 (2.0)
125
(5)
42 (
1.65
)
Adjustableflange
8
Ø50 (1.97”)
Model Suffix Option Descriptioncode codeISC40FD Immersion fittingMaterial -S AISI 316 Stainless steel
-V PVC-CPipe - Between 0.5 and 2.0 meterlength Example: 05 = 0.5 mFlange -NFL No flange
-SFA AISI316 SS 2”-SFD AISI316 SS DN50
Options /MS1 Pipe mounting set (Carbonsteel)
/FA Adjustable flange with DINDN50-PN10 and ANSI 2” 150lbs hole pattern (only for PVC)
/PH5 Protection hose for 5 m cable/PH10 Protection hose for 10 m cable
Material certificate /M 3.1.B, acc. EN 10 204
* the Immersion fitting is delivered without sensor. * the Immersion fitting is delivered without sensor.
GS 12D8J2-E-E
ISC40FD-S (SS)*
Unit: mm (inches)
ISC40FD-V (PVC-C)*Immersion fitting & mounting set (Option /MS1)
9
GS 12D8J2-E-E
Model and Suffix Codes
3. Model ISC40FS Direct insertion subassembliesA. Process temperature
- Model ISC40FS-STW/SCS/S2W: Maximum 150 ºC (300 ºF)
- Model ISC40FS-PCS : Maximum 100 ºC (210 ºF)- Model ISC40FS-FCS : Maximum 130 ºC (270 ºF)
B. Process pressureModel ISC40FS-STW/SCS/S2W
: Max. 1.0 MPa (150 psi) at 150ºC (300ºF)Model ISC40FS-PCS : Max. 0.6 MPa (90 psi) at 20ºC (70ºF)
Max. 0.1 MPa (15 psi) at 100ºC (210ºF)Model ISC40FS-FCS : Max. 1.0 MPa (150 psi) at 20ºC (70ºF)
Max. 0.1 MPa (15 psi) at 120ºC (250ºF)C. Wetted materials
- Model ISC40FS-STW/SCS/S2W: AISI 316 Stainless steel
- Model ISC40FS-PCS : Polypropylene- Model ISC40FS-FCS : PVDF (KYNAR®)- All models : Viton O-ring, EPDM (only S2WN
and STWN)Non wetted materials- Nut : AISI 304 Stainless steel
Dimensions
98 (3.86) 88 (3.46)64 (2.52)
2" NPTacc. ANSI B.20.1
64 (2.52)
82 (
3.23
)
65 (
2.56
)
67 (
2.64
)
12.7
Ø 50 Ø 50
Rd 78 x 1/6acc. DIN 405
Ø 50
Rd 78 x 1/6acc. DIN 405
Dimensions accordingISO 2852: 1993
28.5
Ø 75 Ø 50
PipethreadISO 7/1-R2
Ø 50
2" NPTacc. ANSI B.20.1
Ø 50
Rd 78 x 1/6acc. DIN 405
Rd 78 x 1/6acc. DIN 405
Rd 78 x 1/6acc. DIN 405
PipethreadISO 7/1-R2
35.0
58.0
58.0
58.0
58.0
-S2WN
Unit: mm (inches)
Model Suffix Option DescriptionISC40FS Flow fitting subassemblyMaterial -F PVDF
-P Polypropylene-S Stainless Steel
Process -CS Coupling screw-inconnection -CW Coupling welded
-TW 3” tri-clamp welded-2W 2” tri-clamp welded
Thread type -A NPTNPT or R -J ISO 7/1 R
-N No thread (for weld-in couplings)Options /M Material certificate 3.1.B
-SCWN -SCSA -PCSA-FCSA
-STWN -SCSJ -PCSJ-FCSJ
D. Process connection- Model ISC40FS-STW : 3” tri-clamp- Model ISC40FS-S2W : 2” tri-clamp- Model ISC40FS-SCS/PCS/FCS
: 2” screw-in coupling
E. Shipping details- Dimensions : Refer to section Dimensions- Package : Normally packed with sensor- Weight : 500 g. (1 lbs)
10
GS 12D8J2-E-E
Accessories Spare part sensor carriers and O-rings for the flow through subassemblies and fittings
Part no. Description Material O - ringK1541KC 2” tri-clamp carrier incl. 2 O - rings AISI 316 Stainless steel EPDMK1541KB 3” tri-clamp carrier incl. 2 O - rings AISI 316 Stainless steel EPDMK1541KD 2” carrier incl. 2 O - rings PVDF VitonK1541KL 2” carrier incl. 2 O - rings Polypropylene VitonK1541KA 2” carrier incl. 2 O - rings AISI 316 Stainless steel Viton
O - rings spare parts for sensor ISC40FD and ISC40FS
O-ring materialDimensions EPDM Viton Silicon KALREZ QuantityO- rings for model ISC40FD-S39.35 x 2.62 / 26.57 x 3.53 K1500CE K1500CF K1500CG 5 sets of 2 O - rings39.35 x 2.62 K1500CV 1 O-ring26.57 x 3.53 K1500CH 1 O-ringO- rings for model ISC40FD-V39.35 x 2.62 / 26.57 x 3.53 K1500CX K1500CW K1500CY 5 sets of 3 O - rings44.17 X 1,78O- rings for old model ISC40FD-V44.17 X 1,78 K1541ZS 5 O-ringsO- rings for model ISC40FS /PSCJ /PCSA /FCSJ /FSCA40.64 x 5.33 / 26.57 x 3.53 K1500DF K1500DE K1500DG 5 sets of 3 O - rings56.52 x 5.3340.64 x 5.33 K1500CD 1 O-ring26.57 x 3.53 K1500CH 1 O-ring56.52 x 5.33 K1500DH 1 O-ringO- rings for model ISC40FS /SCSJ /SCSA /SCWN40.64 x 5.33 / 26.57 x 3.53 K1500DB K1500DA K1500DC 5 sets of 3 O - ringsRing NW5040.64 x 5.33 K1500CD 1 O-ring26.57 x 3.53 K1500CH 1 O-ring56.52 x 5.33 K1500DD 1 O-ringO- rings for model ISC40FS /S2WN40.87 x 3.53 / 26.57 x 2.62 K1541ZH K1500DJ K1500DK 2 sets of 3 O-rings2” seal-clampO- rings for model ISC40FS /STWN40.87 x 3.53 / 26.57 x 2. 62 K1541ZK K1500DL K1500DM 2 sets of 3 O-rings3” seal-clampO- rings for old model ISC40 PCSJ /PCSA /FSCJ /FSCA56.52 x 5.33 K1541ZM 5 O-ringsO- rings for old model ISC40 SCSJ /SCSA /SCWNNW25 / NW50 K1541ZJ 2 sets of 2 O - ringsO- rings for old model ISC40 FD and FSViton gasket K1500AM 5 O-rings
Spare Parts ISC40FD
Part no. DescriptionK1500AB Cable gland 1/2 inch NPT (10)K1500AJ O-rings EPDM for /FA (2pcs)K1500AW Flexible conduit, 5 meterK1500AX Flexible conduit, 10 meterK1500AY Connection parts for conduitK1500CB O-ring sets (5 OFF) viton, ISC40/optionsK1500EM /PH25 for immersion holdersK1500DN /PH03 protection hose, 3 meterK1500DN /PH05 protection hose, 5 meterK1500DN /PH10 protection hose, 10 meterK1500DN /PH15 protection hose, 15 meterK1500DN /PH20 protection hose, 20 meter
Spare Parts ISC40FS
Part no. DescriptionK1500BP Clamp seal ring 2" EPDMK1500CB O-ring sets (5 OFF) viton, ISC40/optionsK1500DZ Nut SS, FF/S20-3* + ISC40FF/SK1541KA Holder, ISC40FF-S/ISC40FS-SCK1541KB Holder, ISC40FS-STWNK1541KC Holder, ISC40FS-S2WNK1541KD Holder, ISC40F*-FK1541KL Holder, ISC40F*-P
Options ISC40FF as spare parts
Option Description Material Process connection Part number/FF1 Flange adapter PVDF DN15 PN10 K1521AL/FF2 Flange adapter PVDF DN25 PN10 K1521AP/FF3 Flange adapter PVDF ANSI 1/2"- 150lbs K1521AE/FF4 Flange adapter PVDF ANSI 1"- 150lbs K1521AH/FP1 Flange adapter PP DN15 PN10 K1521AM/FP2 Flange adapter PP DN25 PN10 K1521AQ/FP3 Flange adapter PP ANSI 1/2"- 150lbs K1521AF/FP4 Flange adapter PP ANSI 1"- 150lbs K1521AJ/FS1 Flange adapter AISI 316 SS DN15 PN10 K1521AK/FS2 Flange adapter AISI 316 SS DN25 PN10 K1521AN/FS3 Flange adapter AISI 316 SS ANSI 1/2"- 150lbs K1521AD/FS4 Flange adapter AISI 316 SS ANSI 1"- 150lbs K1521AG/FFJ1 Flange adapter PVDF JIS 10K-15-RF K1543YW/FFJ2 Flange adapter PVDF JIS 10K-25-RF K1543KN/FPJ1 Flange adapter PP JIS 10K-15-RF K1543YY/FPJ2 Flange adapter PP JIS 10K-25-RF K1543KM/FSJ1 Flange adapter AISI 316 SS JIS 10K-15-RF K1543YX/FSJ2 Flange adapter AISI 316 SS JIS 10K-25-RF K1543KL/MS Mounting set Wall/pipe for SS flow fitting K1541ZZ/MP Mounting set Wall/pipe for PP/PVDF flow fitting K1541ZU
Options ISC40FD as spare parts
Option Description Material Process connection Part number/MS1 Pipe mounting set Carbon steel K1541ZY/FA Adjustable flange DIN DN50-PN10 ANSI 2” 150 lbs hole pattern K1520EV
(only for PVC)/PH5 Protection hose for 5 m cable K1500DP/PH10 Protection hose for 10 m cable K1500DQ
11
GS 12D8J2-E-E
Accessories O - ring spare parts for sensor ISC40FF
O-ring materialDimensions EPDM Viton Silicon KALREZ QuantityO- rings for model ISC40FF-S40.64 x 5.33 / 26.57 x 3.53 K1500DB K1500DA K1500DC 5 sets of 3 O-ringsRing NW5040.64 x 5.33 K1500CD 1 O-ring26.57 x 3.53 K1500CH 1 O-ring53.34 x 5.33 K1500DD 1 O-ringO- ring for old model ISC40FF-Sring NW25 / ring NW50 K1541ZJ 2 sets of 2 O-ringsViton gasket K1500AM 5 O-ringsO- ring for model ISC40FF-F and ISC40FF-P40.64 x 5.33 / 26.57 x 3.53 K1500DF K1500DE K1500DG 5 sets of 3 O-rings56.52 x 5.3340.64 x 5.33 K1500CD 1 O-ring26.57 x 3.53 K1500CH 1 O-ring53.34 x 5.33 K1500DD 1 O-ringO- ring for old model ISC40FF-F and ISC40FF-PViton gasket K1500AM 5 O-rings56.52 x 5.33 K1541ZM 1 O-ring
Spare Parts
Part no. DescriptionK1500DZ Nut SS, FF/S20-3* + ISC40FF/SK1541KA Holder, ISC40FF-S/ISC40FS-SCK1541KD Holder, ISC40F*-FK1541KL Holder, ISC40F*-PK1500AB Cable gland 1/2 inch NPT (10)K1500AK O-rings EPDM 29.74x3.53 ( 5)0
K1500AW Flexible conduit, 5 meterK1500AX Flexible conduit, 10 meterK1500AY Connection parts for conduitK1500EM /PH25 for immersion holdersK1500DN /PH03 protection hose, 3 meterK1500DN /PH05 protection hose, 5 meterK1500DN /PH10 protection hose, 10 meterK1500DN /PH15 protection hose, 15 meterK1500DN /PH20 protection hose, 20 meter
12
GS 12D8J2-E-E
Retractable fitting for ISC40G(S)-PR for Inductive Conductivity sensor
The ISC40PR retractable fitting can be applied in all processeswhere it is necessary to remove the sensor without interruptingthe process. The Yokogawa design ensures the safe retraction ofthe sensor from the process without requiring a shut-down.
The optional adapters make selection of a suitable installationeasy. The flanged connection is available in JIS, DIN or ANSI version. The threaded connections are available in R2 or 2” NPT.When inserted, the probe can be locked at any position (betweenthe minimum and maximum) with a locking ring. In addition, theoptional drain port makes it possible to relieve the pressure before complete disassembly.
The choice between stainless steel and titanium (as constructionmaterials) makes use in many applications possible.
Yokogawa recommends using the sensor ISC40- n -PR- n n - n n .For model code see page 14. For safety reasons Yokogawa rec-ommends to use a flanged ball-valve.
Features• Adjustable insertion depth for optimal positioning in the process.• Easy cleaning of the sensor.• Damped probe retraction by o-ring friction with pressurized sys-
tems.• Adaptable to most installations by a range of options.• Optional drain port for relieving pressure, prior to extraction.
General Specificationsa. Materials:
Wetted partsModel ISC40PR-S (Stainless steel) Stainless steel AISI 316
-Probe Stainless steel AISI 316-O-ring seals Viton 70° shore
Model ISC40PR-T (Titanium) Titanium Grade 2 or 3-Probe Stainless steel AISI 316-O-ring seals Viton 70° shore
Non-wetted parts-Stainless steel (AISI 316) and polyphenylene sulphide (PPS)
b. Insertion lengthThe probe length can be adjusted to a maximum of either 0.5or 1 metre. The actual probe insertion length depends on theuse of optional adapters and/or ball valves.The dimensionaldrawing indicates the maximum insertion length for bothspecified probe lengths.
c. Pressure / temperature ratings- Static conditions 2 MPa at 20 °C
500 kPa at 130 °C- Operating conditions maintenance
max. 500 kPamax. 130 °C
- Flange ratings DIN flange DN50 PN16ANSI flange 2” 150 lbsJIS flange 16K - 50
d. WeightApprox 2.5 kg. (stainless steelversion without ball-valve andadapters)
ISC40PRISC40PR/LISC40PR/K
Note: Sensor shown for reference should be ordered separately
13
External Dimensions
500 or 1000 (19.70 or 39.37)
282
(11.
10)
max. 345 or 845 (13.58 or 33.26)
ISO 228/1-G2
140 (5.51)
min.150 (5.9)
max.130 (5.11)
max.160 or 660
(6.29 or 25.98)
min. 150 (5.9)
(NW50 (150mm or 5.9")
(2" ANSI (180mm or 7.08")
max. (NW50)120mm or 620(4.72 or 24.4)
max.130 (5.11)
(2") 90mm or 590(3.54 or 23.22)
Unit: mm (inches)
Options /A, /B, /E, /F Options /C, /G Options /D, /H
ISO 228/1-G2
77 (
3")1/8-27 NPT
UNIVERSAL FLANGE
DIN Flange DN50 PN16ANSI Flange 2" 150 lbsJIS Flange 16K-50
ISO 228/1-G2
54 (
2.12
")
UNIVERSAL FLANGE
DIN Flange DN50 PN16ANSI Flange 2" 150 lbsJIS Flange 16K-50
ISO 228/1-G2
ISO 7/1-R2or
2 -11.5 NPT
* *
*
** Drawn dimensions are for stainless steel
ball valves. They may differ slightly when titanium ball valves are used.
Note: Bolts, nuts and gaskets are notincluded
GS 12D8J2-E-E
Options for -PR Sensor Unit: mm (inches)
14
Ordering Instructions for Spare SensorsSpecify the following when ordering
ISC40 -PR- -
G = General purpose sensorS = Intrinsically safe sensor
T1 = Pt1000T3 = 30K Thermistor
Cable length in metres(03, 05, 10, 15 or 20)
Model Suffix Option DescriptionCodeISC40PR Retractable Fitting, 2” BSP-femaleMaterial -S Stainless steel AISI 316
-T Titanium Grade 2 or 3Probe -05 0.5 mlength -10 1.0 m
/A Adapter R2-G2 (SS AISI 316)/B Adapter 2” NPT-G2 (SS AISI 316)/C Flange adapter (SS AISI 316)/D Flange adapter for drain (SS AISI 316)/E Adapter R2-G2 (Titanium Grade 2 or 3)/F Adapter 2” NPT-G2 (Titanium Grade 2 or 3)/G Flange adapter (Titanium Grade 2 or 3)/H Flange adapter for drain (Titanium Grade 2 or 3)/M Material certificate 3.1.B according to EN 10 204 (DIN 50 049) (on wetted parts)/T Test certificate for hydrostatic pressure test (2 MPa at ambient temperature)/J Ball valve R2 (SS AISI 316)/K Ball valve 2” NPT (SS AISI 316)/L Ball valve 2” ANSI Flanged (SS AISI 316)/N Ball valve DN 50 PN16 Flanged (SS AISI 316)
Model and Suffix Codes
Titanium ball valves are available as separate item
Model Option code DescriptionBV40 Titanium Ball Valve 2”
/P Rc 2/Q 2” NPT/R 2” ANSI/S NW 50
Note: When specifying ISC40PR with a ball valve, ensure thatthe correct adapter is specified also.Example: ISC40PR-S-05/B/KAssembly made of stainless steel, 0.5 metres long, with a2” NPT adapter, and 2” NPT threaded ball valve. Theflanged adapter is designed to suitable 2” ANSI and 50mm DIN flanges.
Wiring Diagram
WHITE
BROWN
RED
BLACK
BLUE
11
12
13
14
15
16
17
BLACK
BLACK
Thermistor (Pt1000)
Secondary
Secondary
Ground
Primary
GS 12D8J2-E-E
Part no. Option DescriptionK1500AH O-ring Kalrez 29.74x3.53K1500BE O-rings viton, SC4A-*-PR (10x)K1500BH Cable gland PG11 for ISC40PRK1500EN Sensor holder SS (ISC40PR)K1500EP Sensor holder Ti (ISC40PR)K1520DD Nut for ISC40PRK1520KC Main fixing screw, retr. holdersK1520KD Clamping ring, retr. holdersK1520KF Position clip assy, retr holderK1520TA Clamping set SS, retr. holderK1520TK Key for retr. holdersK1520UB Clamping set Ti, retr. holderK1541DQ ISC40PR/J Ball valve R2K1541DR ISC40PR/C Flange adapterK1541DS ISC40PR/D Flange adapter for drainK1541DT ISC40PR/G Flange adapterK1541DU ISC40PR/H Flange adapter for drainK1541DW ISC40PR/K Ball valve 2” NPTK1541DX ISC40PR/L Ball valve 2” ANSI FlangedK1541DY ISC40PR/N Ball valve DN 50 PN16 Flanged
Part no. Option DescriptionK1541EJ ISC40PR/A Adapter R2-G2K1541EM ISC40PR/B Adapter 2” NPT-G2K1541EN ISC40PR/E Adapter R2-G2K1541EP ISC40PR/F Adapter 2” NPT-G2K1541DA Ball valve 1” ANSI 150 lbsK1541DB Ball valve DIN DN25 PN16K1541DC Ball valve G1”K1541DD Ball valve 1” NPTK1500BG Viton O-ring setK1500EA EPDM O-ring setK1500EB 2 KALREZ 70 shore O-rings
20.22 x 3.53K1500EC 1 KALREZ 70 shore O-ring
47.22 x 3.53K1500ED 2 KALREZ 70 shore O-rings
15.6 x 1.78K1520UK Outer tube 1/2 mtr S.S.K1520UL Outer tube 1,0 mtr S.S.K1520UM Outer tube 1/2 mtr TiK1520UN Outer tube 1,0 mrt Ti
Options ISC40PR as spare parts
15
Material
PVDF S.S. 316 VITON PEEK PP PVC PFA(Kynar)
Sulfiric acid 10 O O O X X X O O O O O O O O O X O O O50 O O O X X X O O O O O X O O O O O O O95 O X - X X X O O O - - - X - X X O O O
fuming - - - - - - O O O - - - - - - - O O OHydrochloric acid 10 O O O - - - O O O O O X O O OX O O O
sat. O O O - - - O O X O O O O O O ONitric acid 25 O O X X X X O O X O O O O O O X O O O
50 O O X X X X - - - X X X X - O X O O O95 O X - O O O - - - - - - - - - - O O O
fuming - - - O O O - - - - - - - - - - O O OPhosphoric acid 25 O O O - - - O O O O O O O O O X O O O
50 O O O X X X O O O O O O O O O O O O O95 O O O O O O X X - O O O O O O O O O O
Hydrofluoric acid 40 O O O - - - O O O - - - O O OX O O O75 O O O - - - O O O - - - O O XX O O O
Acetic acid 10 O O O O O X - - - O O O O O O X O O Oglacial O X - O O X - - - O O X O X X X O O O
Formic acid 80 O O O X X X - - - X X X O O O - O O XCitric acid 50 O O O O O O O O O O O O O O O O O O OCalcium hydroxide sat. O O O O O O O O O O O O O O O O O O OPotassium hydroxide 50 O O X O O O O O O O O O O O O O O O OSodium hydroxide 40 O O X O O O X X X O O O O O O X O O OAmmonia in water 30 O O O O O O X X X O O O O O O X O O OAmmonium chloride sat. O O O X X X O O O O O O O O O O O O OZinc chloride 50 O O O X X X O O O O O O O O O O O O OIron (III) chloride 50 O O O - - - O O O O O O O O O O O O OSodium sulfite sat. O O O O O O - - - O O O O O O O O O OSodium carbonate sat. O O O O O O O O O O O O O O O O O O OPotassium chloride sat. O O O X X X O O O O O O O O O O O O OSodium sulfate sat. O O O O O O O O O O O O O O O O O O OCalcium chloride sat. O O O X X X O O O O O O O O O O O O OSodium chloride sat. O O O X X X O O O O O O O O O O O O OSodium nitrate 50 O O O X X X O O O O O O O O O O O O OAluminium chloride sat. O O O - - - O O O O O O O O O O O O OHydrogen peroxide 30 O O O O O O O O O O O O O O O O O O OSodium hypochloride 50 O O O X X X O O X O O O X X X X O O OPotassium dichromate sat. O O O O O O O O O O O O O O O O O O OChlorinated lime O X - X X X X X X - - O O O O O
Ethanol 80 O O X O O O X - - O O O O O O X O O OCyclohexane O O X O O O O O O O O O - - O O O O OToluene O O O O O O - - - O O O X - - - O O OTrichloroethane X X X O O X X X X O O O - - - - O O OWater O O O O O O O O O O O O O O O O O O O
20 60 100
20 60 100
20 60 100
20 60 100
20 60 20 60
Inor
gani
c ac
idO
rgan
icac
idA
lkal
iA
cid
salt
Neu
tral
salt
Oxi
dizi
ngag
ent
Org
anic
solv
ent
Temp.ºC
%Conc.
Bas
icsa
lt
O = can be usedX = shortens useful life- = cannot be used
Note: Information in this list is based on our general experience and literature data and given in good faith.However Yokogawa is unable to accept responsobility for claims related to this information.
20 60 100
GS 12D8J2-E-E
Chemical Compatibility Chart
GS 12D8J2-E-ESubject to change without noticeCopyright©
Printed in The Netherlands, 09-502 (A) Q
YOKOGAWA EUROPE B.V.Databankweg 203821 AL AMERSFOORTThe NetherlandsTel. +31-33-4641 611Fax +31-33-4641 610E-mail: [email protected]/eu
YOKOGAWA CORPORATION OF AMERICA2 Dart RoadNewnan GA 30265United StatesTel. (1)-770-253-7000Fax (1)-770-251-2088E-mail: [email protected]/us
YOKOGAWA ELECTRIC ASIA Pte. Ltd.5 Bedok South RoadSingapore 469270SingaporeTel. (65)-241-9933Fax (65)-241-2606E-mail: [email protected]/sg
YOKOGAWA HEADQUARTERS9-32, Nakacho 2-chome,MusashinoshiTokyo 180JapanTel. (81)-422-52-5535Fax (81)-422-55-1202E-mail: [email protected]
Yokogawa has an extensive sales and distribution network. Please refer to the European website(www.yokogawa.com/eu) to contact yournearest representative.