-1-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
FAQ : How To connect Range Extender to existing router via
WPS Setup
Release date : 1/06/2015
Model Support : DAP-1320
H/W:A1 , B1
S/W:1.x , 2.x
-2-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
*Firmware 1.10 and higher
DAP-1320 Push Button WPS Configuration
Note : ถงแมวาจะตงคา DAP-1320 โดยใช WPS คณจะตองมอปกรณของ router/access point ทสามารถรวมกนได
ขนตอนท 1 : เสยบ DAP-1320 ทปลกไฟ Note : ไฟควรจะเปนสแดงแลวเรมกระพรบเปนสสม
-3-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
-4-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
ขนตอนท 2 : กดปม WPS ของ router/AP (ประมาณ 5-7 วนาท)
ขนตอนท 3 : กดปม WPS ของ DAP-1320 คางเอาไวประมาณ 2 วนาท โดยไฟ LED ควรจะเรมตนกระพรบเปนสเขยว เมอสามารถเชอมตอกบเราเตอรของคณแลว ไฟ LED จะหยดกระพรบและจะแสดงนงเปนสเขยว
-5-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
ขนตอนท 4 : ดงปลกออก แลวน ามาวางไวในต าแหนงกงกลางระหวางเราเตอรและต าแหนงทตองการเชอมตอ Note: ต าแหนงทถกตองของ DAP-1320 เปนสงทส าคญมาก โดยมนตองการต าแหนงทสามารถรบสญญาณทดจากเราเตอรของคณ ต าแหนงทดคอต าแหนงกงกลางระหวางเราเตอรและพนททคณตองการรบสญญาณ
-6-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
ขนตอนท 5 : เชอมตอเครอขายไรสายไปยง DAP-1320 แลวสแกนเครอขายไรสายทแสดงในอปกรณเครอขายของคณแลวเชอมตอโดยใช SSID และ รหสผานทแสดงใน configuration note ของคณ
ตอนนการตดตงสมบรณแลว
-7-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Technical Support Setup Procedure
*Firmware 1.10 and higher
DAP-1320 Push Button WPS Configuration
Note: In order to setup the DAP-1320 using WPS, you must have a WPS compatible
router/access point
Step 1: Plug in the DAP-1320
Note: The light should turn red and then start blinking orange
-8-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Step 2: Press the WPS button on your router/AP (usually for about 5-7 seconds)
Step 3: Press and hold the WPS button on the DAP-1320 for 2 seconds. The LED should start to blink green. Once it makes connection with your router the LED will stop flashing and turn solid GREEN.
-9-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Step 4: Unplug and place the DAP-1320 approx half way between the router and the desired connection area.
Note: Correct placement of the DAP-1320 is very important. It needs to be positioned in an area
that still receives good signal from your router. A good starting point is approx half way between
the router and the area you want to get signal to.
Step 5: To connect wireless to the DAP-1320, Scan for available wireless networks on your wireless
device and connect using the Wi-Fi Network Name (SSID) and Wi-Fi Password information located on your configuration note.
-10-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Setup is Complete.
Back to Top
-11-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
ฝายสนบสนนทางดานเทคนค Call Center หมายเลขโทรศพท 02-6617997 ภาษาไทย : จนทร ถง ศกร เวลา 9.00 น. – 18.00 น. Thai : Mon – Fri : Time 9.00 – 18.00. ภาษาองกฤษ : เสาร , อาทตย , วนหยดนขตฤกษ และ วนธรรมดา หลง 18.00 น. English : Sat – Sun , Public Holiday and after 18.00 weekday. Website : www.dlink.co.th
email: [email protected] Facebook : http://www.facebook.com/DLinkThailandFans
-12-
FAQ : How To Connect Range Extender to existing router via WPS setup Version 1.00
Nationwide D-Link Service Centres :