![Page 1: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/1.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities
![Page 2: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/2.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Power system
• Power generation plants are located based on fuel availability
• Other considerations like water, pollution issues etc.• Often they are in remote locations• Loads are situated in population centers• Transporting generated power to population centers for use
requires a power system
![Page 3: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/3.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Why AC?
• Almost the entire power generation and transmission is by AC (alternating current)
• AC lends itself to voltage changes easily
• Voltage can be chosen for optimum efficiency and optimum capital cost
• Thus better economy of power system operations
![Page 4: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/4.jpg)
Technology Training that Workswww.idc-online.com/slideshare
AC Waveform• A voltage or current in AC circuits varies cyclically
a number of times per second• This number is called the frequency (F)• The time for one cycle is thus 1/F• The variation follows a sine relationship and the
waveform is called a sine wave• An electrical system can be of single or 3 phase type
![Page 5: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/5.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Single and three phase generators
![Page 6: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/6.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Three phase AC
• Universally adopted because of lower equipment cost per unit power handled
• Helpful while interconnecting several generating sources (the sources tend remain in phase or stay synchromised)
• Three phase AC motors (which account for most of the energy used) have a simple design and are self starting
![Page 7: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/7.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Electrical Power and Energy
• In DC circuits Power=Voltage x Current (Watts)
Energy= Power x Time (Watt Hours)
• In AC circuits instantaneous voltage and current keep changing as they follow a sine curve– Power is computed using Root Mean Square (RMS)
voltage and RMS current
![Page 8: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/8.jpg)
Technology Training that Workswww.idc-online.com/slideshare
AC Power• Fundamental Definition of Power:
• In an AC circuit both are sinusoidal against time• Sinusoidal Voltage and Current are defined in RMS
magnitudes where:
8
)()()( titvtp
2peak
rms
VV
2peak
rms
II
![Page 9: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/9.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Single Phase AC Power TransmissionTransmission
9
![Page 10: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/10.jpg)
Technology Training that Workswww.idc-online.com/slideshare
The Power Triangle
S
P
Q
22 SPS
S
Prpowerfacto cos
cos*SP sin*SQ
)cos( factorpowera
![Page 11: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/11.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Formulae for Power
• Apparent power S = V*I
• Active Power P = V*I*Cos f
• Reactive Power Q = V*I* Sin f
• Cos f is known as the Power Factor and f is the power factor angle
• The angle depends on the ratio of the resistance to the reactance in a circuit
![Page 12: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/12.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Typical Transmission Substation & transmission lines
![Page 13: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/13.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Power distribution• Distribution is done at lower voltage levels• Distances are much shorter than transmission• Voltage levels are typically 33 kV and less• Bulk of the consumers draw power at lower voltages• This requires distribution at two different levels• Distribution substations convert power from
transmission to distribution voltages• We will discuss the equipment used for T&D in the next
webcast
![Page 14: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/14.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Three phase power network
• All AC generation, Transmission and Distribution is through 3 phase systems– Exception: Single phase/SWER distribution systems
• Utilisation can be 3 phase (motors and rectifiers for drives, furnaces) or single phase (commercial and lighting)
• Ability to transmit larger amount of power for a given voltage/conductor volume
• Availability of rugged 3 phase cage motors with self starting capability
![Page 15: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/15.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Distribution equipment
• Switching and isolation equipment– Circuit breakers– Disconnectors– Control gear
• Conductors for carrying power– Overhead bare– Overhead insulated – UG cables
![Page 16: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/16.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Substations
• A facility incorporating – Transformers – Switching/isolation equipment– Control/protection/measuring– Auxiliary power equipment
• Indoor or Outdoor type• Air-insulated or gas-insulated• Different configurations
![Page 17: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/17.jpg)
Technology Training that Workswww.idc-online.com/slideshare
Outdoor 330 kV switchyard (Transmission)
Typical indoor distribution substation
![Page 18: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/18.jpg)
Technology Training that Workswww.idc-online.com/slideshare
A 400 kV Transmission line and Structure
![Page 19: Electrical and Instrumentation (E&I) Engineering for Oil and Gas Facilities](https://reader033.vdocuments.site/reader033/viewer/2022061613/555ed49ed8b42a772f8b49c7/html5/thumbnails/19.jpg)
Technology Training that Workswww.idc-online.com/slideshare
DO YOU WANT TO KNOW MORE?
If you are interested in further training or information, please visit:
http://idc-online.com/slideshare