Download - EEE114 Engineering Drawing - cu.edu.tr
![Page 1: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/1.jpg)
EEE114
Engineering Drawing
Yrd.Doç. Dr. Engin PINAR
Orthographic Projection
![Page 2: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/2.jpg)
Orthographic projection is a method of producing a number of
separate two-dimensional inter-related views, which are mutually at right angles to
each other. Using this projection, even the most complex shape can be fully described.
Orthographic projection is based on
two principal planes — one horizontal
(HP) and one vertical (VP) —
intersecting each other
Why Orthographic Projection is used in technical drawing
3-D projections are useful in that they provide an image that is similar to the image in
the designer’s mind’s eye. But 3-D projections are often weak in providing adequate
details of the object, and there is often some distortion of the object.
For instance, a circular hole becomes an ellipse in an isometric 3-D projection.
Orthographic projection are used to overcome the weaknesses of 3-D projections.
Orthographic projections are a collection of flat 2-D drawings of the different sides of
an object.
![Page 3: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/3.jpg)
Orthographic projection is a parallel projection technique
in which the parallel lines of sight are perpendicular to the
projection plane 3-D projections are useful in that they provide an
image that is similar to the image in the designer’s
mind’s eye. But 3-D projections are often weak in
providing adequate details of the object, and there is
often some distortion of the object.
For instance, a circular hole becomes an ellipse in
an isometric 3-D projection. Orthographic
projection are used to overcome the weaknesses
of 3-D projections. Orthographic projections are a
collection of flat 2-D drawings of the different sides
of an object.
Orthographic view
![Page 4: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/4.jpg)
Orthographic view depends on relative position of the object to
the line of sight. It uses multiple views of the object, from points of
view rotated about the object's center through increments of 90°.
The views may be
considered to be obtained
by rotating the object
about its center through
increments of 90°.
Orthographic view
![Page 5: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/5.jpg)
It represents accurate shape and size. Advantage
Disadvantage Require practice in writing and reading.
Multiviews drawing (2-view drawing) Example
Orthographic View
![Page 6: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/6.jpg)
Only two forms of orthographic
projections are used: first-angle
projection (‘European ISO-E’)
and third-angle projection
(‘American ISO-A’).
On engineering drawings, the
projection angle is
denoted by an international
symbol consisting of
a truncated cone, respectively
for first-angle
(FR) and third-angle (US):
(‘European ISO-E’) (‘American ISO-A’)
Orthographic View
![Page 7: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/7.jpg)
STEP 1 : Orient the Object
NO !
Orient the object to the best position relative to a glass box. The
object should presents its features in actualsize and shape
in orthographic views.
GOOD
View Selection Steps
![Page 8: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/8.jpg)
STEP 2 : Select a Front View
The object’s longest dimension should be
presented as a width.
Inappropriate
First choice Second choice
Waste more space
![Page 9: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/9.jpg)
STEP 2 : Select a Front View
Choose the view that have the fewest number of
hidden lines.
GOOD Inappropriate
![Page 10: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/10.jpg)
STEP 3 : Select an Adjacent View
GOOD
Inappropriate
Inappropriate
GOOD
Choose the view that have the fewest number of
hidden lines and minimum number of views that
can represent the major features of the object
![Page 11: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/11.jpg)
Object Features
Edges are lines that represent the boundary
between two faces.
Corners Represent the intersection of two or
more edges.
Edge
Corner
Edge No edge
No corner No corner
![Page 12: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/12.jpg)
Surfaces are areas that are bounded by edges
or limiting element.
Limiting
element
is a line that represents the last visible
part of the curve surface.
Surface Surface Surface
Limit Limit
Object Features
![Page 13: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/13.jpg)
Standard Views of Primitive Solids
![Page 14: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/14.jpg)
Fillets, Rounds & Chamfers
![Page 15: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/15.jpg)
Edge Lines – Principal & Inclined
Principal lines appear vertical,
horizontal or as point views.
Inclined lines appear inclined in
one view.
2
Edge lines are lines that
represent the boundary
between two faces
![Page 16: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/16.jpg)
Edge Lines – Oblique
Oblique line appears inclined in all views
![Page 17: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/17.jpg)
Type of Planes
Principal
Oblique
Inclined Oblique
surface
![Page 18: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/18.jpg)
Principal Planes Principle planes are parallel to principal orthographic
planes
Principal planes appear in true
size in one plane and as an
edge view in the other two
planes.
![Page 19: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/19.jpg)
Inclined Planes
Inclined planes are perpendicular to two opposite
orthographic planes.
![Page 20: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/20.jpg)
Oblique Planes
Oblique planes are neither parallel nor
perpendicular to any principal orthographic planes.
Oblique
surface
![Page 21: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/21.jpg)
Top view
![Page 22: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/22.jpg)
![Page 23: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/23.jpg)
Standards are set of rules that govern how Technical
drawings are represented.
Drawing standards are used so that drawings convey
the same meaning to everyone who reads them.
Basic Line Types
![Page 24: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/24.jpg)
Basic Line Types
Types of Lines Appearance Name according
to application
Continuous thick line Visible line
Continuous thin line Dimension line
Extension line
Leader line
Dash thick line Hidden line
Chain thin line Center line
![Page 25: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/25.jpg)
Visible lines represent features that can be seen in the
current view
Meaning of Lines
Hidden lines represent features that can not be seen in
the current view
Center line represents symmetry, path of motion, centers
of circles, axis of axisymmetrical parts
Dimension and Extension lines indicate the sizes and
location of features on a drawing
![Page 26: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/26.jpg)
Example : Line conventions in engineering drawing
![Page 27: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/27.jpg)
LINE CONVENTION
Precedence of coincide lines.
Hidden line drawing.
Center line drawing.
![Page 28: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/28.jpg)
PRECEDENCE OF LINE
Visible
line Order of
importance
Hidden
line
Center
line
Coincide
with
center
line
![Page 29: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/29.jpg)
Using a dash line for
representing the hidden edge.
EXAMPLE : Already met convention practice
Front view
CONVENTION
PRACTICE
![Page 30: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/30.jpg)
Hiden Line Practice
Hidden line should join a visible line, except it
extended from the visible line.
Correct
No !
Join
Leave
space
![Page 31: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/31.jpg)
Correct No !
Hidden line should join a visible line, except it
extended from the visible line.
Leave
space Leave
space
Hiden Line Practice
![Page 32: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/32.jpg)
Hidden line should intersect to form L and T
corners.
Correct
No !
L T
HIDDEN LINE PRACTICE
![Page 33: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/33.jpg)
Hidden arcs should start on a center line.
Hiden Line Practice
![Page 34: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/34.jpg)
Center Line Practice
In circular view, short dash should cross at the intersections of center
line.
For small hole, center line is presented as thin continuous line.
Center line should not extend between views.
Leave space
Leave space
![Page 35: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/35.jpg)
Leave the gap when centerline forms a continuation
with a visible or hidden line
Leave
space Leave
space Leave
space
Leave
space
Center line should always start and end with
long dash.
Center Line Practice
![Page 36: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/36.jpg)
F
A
B C
F D E
G
A
B C
D
E F G
S
T
F
![Page 37: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/37.jpg)
F
A
B
C
F
D
E
G
H I
A B
C
D
E
F
G
H I
S
T
F
![Page 38: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/38.jpg)
F
A B
C
D
E A B
C
D E
S
T
F
![Page 39: EEE114 Engineering Drawing - cu.edu.tr](https://reader030.vdocuments.site/reader030/viewer/2022012802/61bd116d61276e740b0f060f/html5/thumbnails/39.jpg)
F
A
H
S
T
F
A
B
C
D
B C D