![Page 1: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/1.jpg)
Interferometric Sounder Concept for Ice Sheet Mapping
Review, Simulations, Spaceborne System, Future
E. Rodriguez
Jet Propulsion Laboratory
California Institute of Technology
![Page 2: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/2.jpg)
Talk Outline
• Motivation for examiniming the interferometric sounder concept
• Description of interferometric sounder concept and simulation results
• A possible spaceborne implementation
![Page 3: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/3.jpg)
Conventional Sounding is Insufficient
• Nadir sounding full coverage is not sufficient to meet science requirements:– Beam limited spatial resolution (1km) requires
antenna size beyond current capabilities (420 m at P-band)
– Available bandwidth (and range resolution) insufficient for desired 10m height accuracy: 6MHz gives a range resolution of 13.8 m in ice. Worse at VHF.
– Full spatial coverage requires many years of mission lifetime (and large costs)
![Page 4: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/4.jpg)
Conventional Interferometry is Insufficient
• Coverage, spatial resolution, and height accuracy suggest that a swath SAR interferometer might meet requirements
• However, contributions from ambiguous returns from surface clutter and the opposite side basal layer make this approach not feasible
• An alternate approach: multiple baselines to resolve subsurface/surface. Expensive and hard to implement:– In order to get sufficient number of different
baselines a large number of antennas are required– The technique is very sensitive to calibration and to
having good SNR– Data rate is very large
![Page 5: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/5.jpg)
Range Ambiguities for Sounding
Similar ambiguities exist on the opposite side of the nadir track
Geometry of the two layer scattering model. H is the spacecraft height above a reference surface; h is the ice surface height above the reference surface; D is the average depth of the basal layer; d is the topographic variations of the basal layer; xb is the cross-track coordinate of the basal layer point under observation; and, xs is the cross-track coordinate of the surface point whose two-way travel time is the same as the two-way travel time for xb.
![Page 6: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/6.jpg)
Ground Resolution vs Bandwidth
![Page 7: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/7.jpg)
Clutter Effect on Interferometric Error
Height error as a function of signal to clutter () for a baseline of 45 m and a center frequency of 430~MHz (solid lines) and 130 MHz (dashed lines). The values of () are: 1 (blue), 0.1 (red), and 0.01 (black).
![Page 8: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/8.jpg)
Height Noise vs SNR
Height error as a function of SNR for a baseline of 45m and a center frequency of 430 MHz (solid lines) and 130 MHz (dashed lines). The values of SNR are: 0 dB (blue), -5 dB (red), and -10 dB (black). The number of looks is assumed to be 100.
![Page 9: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/9.jpg)
Scattering Area Ratio: Loss of SNR for Off-Nadir Geometry
Ratio of the basal to surface scattering areas. Notice that away from the nadir direction, this ratio quickly approaches 1.
![Page 10: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/10.jpg)
Interferometric Sounding Concept
• Conventional interferometry uses phase information one pixel at a time
• However, there is additional information contained in the spatial frequency of the phase:– Opposite side ambiguities have opposite interferometric
frequencies: while the phase in one side increases with range, it decreases with range in the opposite side (+/- spatial frequencies of complex interferogram)
– Because of the difference in incidence angles, the near nadir interferometric phase spatial frequency is much larger than the equivalent frequency for surface clutter
• IFSAR sounding concept: spatially filter interferogram to retain only basal returns
![Page 11: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/11.jpg)
Surface x-Track Distance vs Basal x-Track Distance
Surface cross-track distance xs as a function ofbasal cross-track distance xb for a platform height of 600km. Notice that near nadir xs is nearly independent of xb, while for xb > 50 km, the two are close to being linearly dependent.
![Page 12: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/12.jpg)
Surface Ambiguous Incidence Angle
Surface incidence angle s as a function of xb for a platform height of 600 km. As expected, the behavior matches that of xs.
![Page 13: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/13.jpg)
Basal Incidence and Look Angles
Basal layer incidence angle 2 as a function of xb for a platform height of 600km (solid lines). Notice that, since the dependent on depth is of order D/H, the incidence angle is nearly independent of depth.The apparent look angle, 1 is also plotted using dashed lines.
![Page 14: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/14.jpg)
Interferometric Phase and Phase Frequency
€
Φb ≈ 2kBθ1
€
Φs ≈ 2kBθ s
€
κ s ≈ 2kB1
xs−hxH
⎛
⎝ ⎜
⎞
⎠ ⎟
€
κ s ≈ 2kB1
xb−
dxn(H + D /n)
⎛
⎝ ⎜
⎞
⎠ ⎟
Surface interferometric phase difference
Basal interferometric phase difference
Surface Interferogram slope as a function of range.hx is the surface topography cross-track slope Basal Interferogram slope
as a function of range.dx is the surface topography cross-track slope
€
I =αe iΦ b + βe iΦ s Complex interferogram
![Page 15: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/15.jpg)
UHF Fringe SpectrumNo Antenna Pattern
Interferogram spectra for signal to clutter ratio of 1, radar frequency of 430MHz, bandwidth of 6MHz, for the first 50 km of xb. The basal spectrum is colored orange. The remaining curves show the surface spectra for D = 1 km (black), D = 2 km (red), D = 3 km (green),D = 4 km (blue). Notice that the basal fringe spectrum depends very weakly on depth
![Page 16: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/16.jpg)
What is the Effect of Surface Slopes?
€
Δκ s = 2kBσ hxH
Spectral broadening due to surface slopes
€
Δκ sκ s
<xsH
<<1 Relative spectral broadening is much less than the spectral peak, as long as the angle of incidence is small: changes in the angle of incidence are dominated by changes in cross-track distance rather than changes in slope. This argument does not hold for higher incidence angles.
![Page 17: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/17.jpg)
Filter Design• In range space, both the basal fringe rate and the surface fringe rate are spatially varying
• The basal layer is hard to model (unknown topography and reflectivity)
• The surface layer is easy to model: smooth topography and small changes in reflectivity. However, the topography may not be totally known
• To narrow the surface spectrum, re-project data from range space to a plane near the surface. In this coordinate system, the surface fringe rate is approximately constant
-Empirically, one can see a significant narrowing of the surface contribution and better separation between the two
• Two algorithms examined:
-Surface contribution is frequency shifted to 0 frequency by applying a phase ramp and the basal return is extracted via a band-pass filter. Problems near antenna pattern nulls or strong gradients
- A fit is made to the surface interferogram, including antenna pattern variations.Band-pass filter design is still being optimized.
![Page 18: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/18.jpg)
Height Error After Interferometric Filtering: 45m Baseline No Antenna
Assumed clutter to signal ratio (same side): 0dB
Assumed clutter to signal ration (opposite side): -3dB
Assumed SNR: 0dB
Assumed number of spatial looks: 100
![Page 19: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/19.jpg)
Topographic Simulation ResultsResults Similar to Xiaoqing’s
Basal Interferogram Surface InterferogramTopography Weighted by Gain
RangeRange Distance (km)
![Page 20: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/20.jpg)
Antenna Pattern Results: 2 km
Basal Return Surface Return
Before filtering After filtering
![Page 21: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/21.jpg)
Antenna Pattern Results: 3 kmWhat should be done about long wavelength
brightness variations?
Before filtering After filtering
Basal Return Surface Return
![Page 22: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/22.jpg)
Problems with Simple Band-Pass
• Low frequency envelop variations broaden spectrum and cause simple FFT or FIR based algorithms to either extract too much signal or leave too many sidelobes
• The latest filter, still under development, uses least squares fitting of the expected surface signal, including antenna pattern variations
![Page 23: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/23.jpg)
Spaceborne Radar Concept
• Use P-band interferometer with two antennas and 30m - 60m baseline separation
• Use SAR processing to obtain along track resolution
• Use polarimetric radar to remove ionospheric effects
• Align antennas so that conventional nadir sounding is possible at the same time as interferometric sounding– Use conventional sounding for layering studies and as
calibration for interferometer at cross-over points– Use Interferometric sounding from 10 km to 60 km
![Page 24: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/24.jpg)
Key Instrument Parameters
Polarimetric radar (4 channels)center frequency (Hz) = 430.e6bandwidth (Hz) = 6.e6pulse length (sec) = 20.e-6peak transmit power (W) = 5000.system losses (dB) = -3.receiver noise figure (dB) = 4platform height (km) = 600azimuth resolution (m) = 7prf (Hz) = 10000Duty cycle (%) = 20antenna length (m) = 12.5antenna efficiency (dB) = -2. ! 1-wayantenna boresight angle (deg) = 2.5wavelength (m) = 0.7baseline (m) = 45. swath (km) = 50Minimum number of looks = 500.
![Page 25: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/25.jpg)
Sounder Performance 1 km Ice
![Page 26: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/26.jpg)
Sounder Performance 2 km Ice
![Page 27: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/27.jpg)
Sounder Performance 3 km Ice
![Page 28: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/28.jpg)
Sounder Performance 4 km Ice
![Page 29: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/29.jpg)
Ongoing Work at JPL to Support the IIP• For the IIP, it is very likely that platform motion will play a significant role
• Conventional processors which work in the frequency domain, are not very well suited to handle large motion plus ray bending
• Given improvements in computing, one can solve do an exact time-domain back-propagation to achieve optimal focusing
• This is the slowest algorithm, but makes no approximations
• Results from other processors (KU, Vexcel) can be verified against exact results
• JPL simulator makes approximations, but is significantly faster to run than the sophisticated Vexcel simulator (previous secene completed in a few minutes)
• This tool can be used for system engineering studies to assess performance tradeoffs (e.g., antenna pattern design, optimal element combination)
• The clutter removal filter is still being optimized: handle nulls
![Page 30: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/30.jpg)
Backup Slides
![Page 31: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/31.jpg)
Estimated One-Way Absorption
Absorption losses present severe constraints on system design if an SNR > 0dB is desired. Together with pulse length considerations, this leads to a desired peak power of ~5kW, which is technologically feasible at P-Band and VHF.
![Page 32: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/32.jpg)
Radar Frequency Selection• Select P-band (430MHz) to minimize baseline
length, antenna size and range resolution – Antenna length of 12.5 m consistent with demonstrated
space technology (TRL 9)– Baseline range between 30m to 60m consistent with
SRTM mast (TRL9)– 6MHz bandwidth possible at P-band– Higher clutter mitigated by interferometric sounder
technique
• VHF may be feasible using repeat pass interferometry, although antenna size (~40m) may be problematic.– Can one increase VHF bandwidth over the polar regions?
![Page 33: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/33.jpg)
Desired Swath Altitude
• A 50 km swath will enable a mission lifetime < 4 months => cost savings
• A 50 km swath is consistent with the interferometric sounder approach for a height of 600 km and a 6 MHz bandwidth
• Heights lower than 600 km will require a decrease in swath and a consequent increase in mission lifetime (although this is not a strong constraint).
![Page 34: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/34.jpg)
Assumed Antenna Pattern
• Assume uniform circular illumination
• Antenna diameter 12.5m– Consistent with available
space qualified antennas
• Antenna boresight: 1.5deg
• Assumed antenna efficiency: -2dB 1-way
![Page 35: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/35.jpg)
Pulse Length Selection
• In order to minimize contamination from nadir surface return, use short 20musec chirp– Surface nadir return sidelobes stops after
1.7 km of ice depth
• Much longer pulses will contaminate basal returns significantly
• Use high power and high PRF to overcome ice propagation loss
![Page 36: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/36.jpg)
PRF Selection
• Required PRF to for SAR synthetic aperture: ~1KHz
• Use significantly higher PRF (~7Hz - 10Hz) together with onboard presumming to improve signal to noise ratio.
• Instrument duty cycle: ~20%
![Page 37: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/37.jpg)
Model Backscatter Cross Section
• The backscatter model consists of two contributions:– Geometrical optics
(surface RMS slope dependent)
– Lambertian scattering
• assumed Lambertian contribution at nadir: -25dB
![Page 38: E. Rodriguez Jet Propulsion Laboratory California Institute of Technology](https://reader035.vdocuments.site/reader035/viewer/2022062516/56812b9b550346895d8fbf7c/html5/thumbnails/38.jpg)
Observed Surface Sigma0 Angular Dependence at 120 MHz
• Data obtained with the JPL Europa Testbed Sounder in deployment with the Kansas U. sounder over Greenland
• Angular decay near nadir (>15 dB in 5 degrees) consistent with very smooth ice surface
• Change in behavior at P-band is still unknown, but probably bounded by 1-3 degree slope models