13.01
Han® Q
HanQ
Contents
Page
Technical characteristics Han® Q 5/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.10
Han® Q 5/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.11
Technical characteristics Han® Q 7/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.14
Han® Q 7/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.15
Standard Hoods/Housings for Han® Q 5/0 and Q 7/0 . . . . . . . . . . . . . . . . . . 13.12
Technical characteristics Han® Q 8/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.16
Han® Q 8/0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.17
Technical characteristics Han® Q 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.18
Han® Q 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.19
Technical characteristics Han® Q 4/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.20
Han® Q 4/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.21
Han-Compact® Hoods/Housings for Han® Q 8/0 and Han® Q 17 . . . . . . . . . 13.22
13.10
HanQ
Han® Q 5/0
Features Technical characteristics 5 contact chambers for the power contacts of
the series Han E® (16 A)
Space-saving and compact design
Leading protective ground with screw terminal
Crimp terminal with standard Han E® contacts
Use of standard tools
Compatible with metal and plastic hoods of theseries Han® 3 A / 4 A
The contacts can be removed with the aid of aremoval tool from the termination side
Degree of protection IP 652)
Current carrying capacityThe current carrying capacity is limited by maximum temperatureof materials for inserts and contacts including terminals. Thecurrent capacity-curve is valid for continuous, not interruptedcurrent-loaded contacts of connectors when simultaneous poweron all contacts is given, without exceeding the maximum tempe-rature.
Control and test procedures according to DIN IEC 60 512-3.
Wor
king
cur
rent
Ambient temperature
Wire gauge: 2.5 mm2
Wire gauge: 1.5 mm2
Specifications DIN VDE 0627DIN VDE 0110DIN EN 61 984
Approvals ,
InsertsNumber of contacts 5 + PE
Electrical data acc. to DIN EN 61 984 16 A 230/400 V 4 kV 3
Working currentWorking voltage conductor – groundWorking voltage conductor – conductorRated impulse voltagePollution degree
– Pollution degree 2 also 16 A 320/500 V 4 kV 2
Working voltageaccording to CSA 600 V
Insulation resistance ≥ 1010 ΩMaterial PolycarbonateLimiting temperatures – 40 OC / + 125 OCFlammability acc. to UL 94 V 0Mechanical working life
- mating cycles ≥ 500
ContactsMaterial copper alloySurface
- hard-silver plated 3 µm Ag- hard-gold plated 2 µm Au over 3 µm Ni
Contact resistance ≤ 1 mΩCrimp terminal
- mm² 0.5 - 2.5 mm²- AWG 20 - 14
Plastic Hoods/HousingsMaterial Polycarbonate RAL 7032Locking element Polyamide RAL 7032Flammability acc. to UL 94 V 0Hoods/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN
40 050 for coupled connector IP 67
Metal Hoods/HousingsMaterial die cast zinc alloyLocking element steel, galvanizedHoods/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN40 050 for coupled connector IP 44
IP 67 with sealing screw09 20 000 9918
Further selection of hoods/housings chapter 30 / chapter 31
AccessoriesCrimping tools chapter 99Cable clamps chapter 40IP 65 fixing screw chapter 40
13.11
M
F
HanQ
09 12 005 3101
09 12 005 3001
09 33 000 9954
Han® Q 5/0 230/400 V 16 A
20 10 001 3311 20 10 001 3321
Crimp terminalOrder crimp contactsseparately
Part No.
Identification Male insert (M) Female insert (F) Drawing Dimensions in mm
Inserts
Number of contacts
5
Contact arrangementView from termination side
Size 3 A
Operating contactIdentification
Crimp contact identification
Relay contact
Stock items in bold type* only to be used with BUCHANAN crimping tool 09 99 000 0001 and adjustment gauge 09 99 000 0203
Coding Pin
Wire gauge Part No.
Identification (mm2) Male contacts Female contacts Drawing Dimensions in mm
Crimp contactsHan E® contacts
Power contacts 0.14-0.37 *09 33 000 6127* *09 33 000 6227*0.5 09 33 000 6121 09 33 000 62200.75 09 33 000 6114 09 33 000 6214silver plated 1.0 09 33 000 6105 09 33 000 62051.5 09 33 000 6104 09 33 000 62042.5 09 33 000 6102 09 33 000 6202
0.14-0.37 *09 33 000 6117* *09 33 000 6217*0.5 09 33 000 6122 09 33 000 62220.75 09 33 000 6115 09 33 000 6215gold plated 1.0 09 33 000 6118 09 33 000 62181.5 09 33 000 6116 09 33 000 62162.5 09 33 000 6123 09 33 000 6223
Relay contacts 0.75-1 09 33 000 6109silver plated 1.5 09 33 000 6110
2.5 09 33 000 6111
StrippingIdentification Wire gauge length
no groove 0.14-0.37 mm² AWG 26-22 7.5 mmno groove 0.5 mm² AWG 20 7.5 mm1 groove* 0.75 mm² AWG 18 7.5 mm1 groove 1. mm² AWG 18 7.5 mm2 grooves 1.5 mm² AWG 16 7.5 mm3 grooves 2.5 mm² AWG 14 7.5 mm
* on the back crimp collar
FOC contactsfor 1 mm plastic fibre
Crimp zone Crimp zone
Use of the coding pin prevents incorrect mating to other connectors of the same type.
The male pin should beomitted from the opposingcavity in the male insert.
13.12
HanQ
Han® Q 7/0
Features 7 contact chambers taking the control contacts
of the series Han D® (10 A)
Space-saving and compact design
Crimp terminal with standard Han D® contacts
Insert is suitable for the hoods and housingsof the series Han® 3A
The contacts can be removed with the aid of aremoval tool from the mating side
6 fold coding by means of a coding pin
Current carrying capacity
The current carrying capacity is limited by maximum temperatureof materials for inserts and contacts including terminals. Thecurrent capacity-curve is valid for continuous, not interruptedcurrent-loaded contacts of connectors when simultaneous poweron all contacts is given, without exceeding the maximum termpe-rature.
Control and test procedures according to DIN IEC 60 512-3.
Wor
king
cur
rent
(A
)
Ambient temperature (C°)
Wire gauge: 1,5 mm2
0,75 mm2
Technical characteristicsSpecifications DIN VDE 0627
DIN VDE 0110DIN EN 61 984
Approvals
InsertsNumber of contacts 7 + PE
Electrical dataacc. to DIN EN 61 984 10 A 400 V 6 kV 3
Working currentWorking voltageTesting voltagePollution degree
– Pollution degree 2 also 10 A 230/400 V 6 kV 2
Working voltageaccording to UL 600 V
Insulation resistance ≥ 1010 ΩMaterial PolycarbonateLimiting temperatures – 40 OC / + 125 OCFlammability acc. to UL 94 V 0Mechanical working life
- mating cycles ≥ 500
ContactsMaterial Copper alloySurface
- hard-silver plated 3 µm Ag- hard-gold plated 2 µm Au over 3 µm Ni
Contact resistanceCrimp terminal ≤ 3 mΩ
- mm² 0.14 - 2.5- AWG 26 - 14
PE screw terminal- mm² 2.5- AWG 14
Plastic hoods/housingsMaterial Polycarbonate Locking element Polyamide Flammability acc. to UL 94 V 0Hood/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 67
Metal hoods/housingsMaterial die cast zinc alloyLocking element steel galvanizedHoods/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 44
IP 67 with sealing screw09 20 000 9918
AccessoriesCrimping tools chapter 99
13.13
HanQ
Han® Q 7/0
20 10 001 3211 20 10 001 3221
09 12 007 3001 09 12 007 3101
09 12 000 9901 09 12 000 9902
M F
400 V 10 A
Stock items in bold type* partly loaded insert
FOC contactsfor 1 mm plastic fibre
Crimp terminalOrder crimp contactsseparately
Coding
Part No.
Identification Male insert (M) Female insert (F) Drawing Dimensions in mm
Inserts
Number of contacts
7
Wire gauge Part No.
Identification (mm2) Male contacts Female contacts Drawing Dimensions in mm
Crimp contactsHan D® contacts
0.14-0.37 09 15 000 6104 09 15 000 62040.5 09 15 000 6103 09 15 000 6203
silver plated 0.75 09 15 000 6105 09 15 000 62051.0 09 15 000 6102 09 15 000 62021.5 09 15 000 6101 09 15 000 62012.5* 09 15 000 6106 09 15 000 6206
0.14-0.37 09 15 000 6124 09 15 000 62240.5 09 15 000 6123 09 15 000 62230.75 09 15 000 6125 09 15 000 6225
gold plated 1.0 09 15 000 6122 09 15 000 62221.5 09 15 000 6121 09 15 000 62212.5* 09 15 000 6126 09 15 000 6226
StrippingWire gauge ø length
0.14-0.37 mm2 AWG 26-22 0.90 mm 8 mm0.5 mm2 AWG 20 1.10 mm 8 mm0.75 mm2 AWG 18 1.30 mm 8 mm1. mm2 AWG 18 1.45 mm 8 mm1.5 mm2 AWG 16 1.75 mm 8 mm2.5 mm2 AWG 14 2.25 mm 6 mm
View from termination
side
View from termination
side
Size 3 A
13.14
HanQ
09 20 003 0801
09 20 003 0301
19 20 003 1250 20
19 20 003 1252 20
19 20 003 1150 20
19 20 003 1750 20
09 20 003 54221)
09 20 003 54212)
09 20 003 54261)
09 20 003 54252)
09 20 003 54281)
09 20 003 54272)
09 20 003 03051)
09 20 003 03062)
19 20 003 1640 20
19 20 003 1440 20
Hoods/Housings metal Size 3 A
Identification Part No. M Drawing Dimensions in mm
1) for mounted male insert 2) for mounted female insert Stock items in bold type
Hoo
dsH
ousi
ngs
Panel cut out22 x 22 mm
Panel cut out22 x 22 mm
Housingsbulkhead mounting
Housingsurface mounting
1 side-entry
bottom closed
Housingscrew mounting
Hoodcable to cable
Protection coversfor hoods
Protection coversfor housings
for hoods cable to cable
with fixed cover
without sealing
with sealing
Hoodside-entry
Hoodtop-entry
13.15
HanQ
A B
C
A 09 20 003 54071)3)1)
09 20 003 54082)3)4)
B 09 20 003 54452)1)1)
09 20 003 54461)1)1)
09 20 003 54472)3)4)
C 09 20 003 54481)1)1)
Hoods/Housings thermoplastic Size 3 A
Identification Part No. M Drawing Dimensions in mm
Hoo
ds
Hoodsside-entry grey
19 20 003 0620 20
black19 20 003 0627 20
Protection coversfor hoods
09 20 003 54421)
09 20 003 54412)
Hou
sing
s
Housingsbulkhead mounting
grey09 20 003 0320 –
black09 20 003 0327 –
grey09 20 003 0820 –
black09 20 003 0827 –
Housingssurface mounting1 side-entry grey
19 20 003 0220 20
black19 20 003 0227 20
Hoodscable to cable
grey19 20 003 0720 20
black19 20 003 0727 20
Panel cut out 22 x 22 mm
Panel cut out 22 x 22 mm
grey19 20 003 0420 20
black19 20 003 0427 20
Hoodstop-entry
Stock items in bold type1) for mounted male insert2) for mounted female insert
3) for metal housings and cable to cable hoods also4) for mounted Han-Brid® male and female insert
for housings
for hoods cable to cable
Protection covers
13.16
*
HanQ
Han® Q 8/0
Features Technical characteristics 8 contact chambers taking
the Han E® power contacts
Space-saving and compact design
Leading protective ground
Crimp terminal with standardHan E® contacts
Use of standard tools
Insert is suitable for the hoods and housingsof the series Han® Q 8/0
The contacts can be removed withthe aid of a removal tool from thetermination side
conform product
Current carrying capacityThe current carrying capacity is limited by maximum temperatureof materials for inserts and contacts including terminals. Thecurrent capacity-curve is valid for continuous, not interruptedcurrent-loaded contacts of connectors when simultaneous poweron all contacts is given, without exceeding the maximum termpe-rature.
Control and test procedures according to DIN IEC 60 512-3.
Wor
king
cur
rent
(A
)
Ambient temperature (C°)
Control and test procedures according to DIN IEC 512-3Wire gauge: 2.5 mm2
1.5 mm2
* DESINA is a registered trademark
Specifications DIN VDE 0627DIN VDE 0110DIN EN 61 984
Approvals
InsertsNumber of contacts 8 + PE
Electrical dataacc. to DIN EN 61 984
Mounted plastic hood 16 A 500 V 6 kV 3
Working currentWorking voltageRated impulse voltagePollution degree
– Pollution degree 2 also 16 A 400/690 V 6 kV 2
Mounted metal hood 16 A 230/400 V 4 kV
Working voltageacc. to UL 500 V
Insulation resistance ≥ 1010 ΩMaterial PolycarbonateLimiting temperatures – 40 OC / + 125 OCFlammability acc. to UL 94 V 0Mechanical working life
- mating cycles ≥ 500
ContactsMaterial Copper alloySurface
- hard-silver plated 3 µm Ag- hard-gold plated 2 µm Au over 3 µm Ni
Contact resistanceCrimp terminal < 1 mΩ
- mm² 0.5 - 2.5 mm²partly loaded up to 4 mm²is possible
- AWG 20 - 14
Plastic hoods/housingsMaterial Polycarbonate RAL 9005Locking element Polyamide RAL 9005Flammability acc. to UL 94 V 0Hood/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 65
Metal hoods/housingsMaterial die cast zinc alloyLocking element V2A steelHoods/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 65
AccessoriesCrimping tools chapter 99
09 33 000 9954
13.17
HanQ
Han® Q 8/0 500 V 16 A
09 12 008 3101 F
09 12 008 3001 M
20 10 001 3311 20 10 001 3321
Part No.
Identification Male insert (M) Female insert (F) Drawing Dimensions in mm
Inserts
Number of contacts
8
Crimp terminalOrder crimp contactsseparately
Contact arrangementView from termination side
Wire gauge Part No.
Identification (mm2) Male contacts Female contacts Drawing Dimensions in mm
Crimp contactsHan E® contacts
Power contacts 0.14-0.37 *09 33 000 6127* *09 33 000 6227*0.5 09 33 000 6121 09 33 000 62200.75 09 33 000 6114 09 33 000 6214
silver plated 1.0 09 33 000 6105 09 33 000 62051.5 09 33 000 6104 09 33 000 62042.5 09 33 000 6102 09 33 000 62024.0 09 33 000 6107 09 33 000 6207
0.14-0.37 *09 33 000 6117* *09 33 000 6217*0.5 09 33 000 6122 09 33 000 62220.75 09 33 000 6115 09 33 000 6215
gold plated 1.0 09 33 000 6118 09 33 000 62181.5 09 33 000 6116 09 33 000 62162.5 09 33 000 6123 09 33 000 62234.0 09 33 000 6119 09 33 000 6221
Relay contacts0.75-1 09 33 000 6109
silver plated 1.5 09 33 000 61102.5 09 33 000 6111
Operating contactIdentification
Relay contact
Stock items in bold type
FOC contactsfor 1 mm plastic fibre
Crimp zone Crimp zone
* only to be used with BUCHANAN crimping tool 09 99 000 0001 and adjustment gauge 09 99 000 0203
Coding Pin
StrippingIdentification Wire gauge length
no groove 0.14-0.37 mm² AWG 26-22 7.5 mmno groove 0.5 mm² AWG 20 7.5 mm1 groove* 0.75 mm² AWG 18 7.5 mm1 groove 1. mm² AWG 18 7.5 mm2 grooves 1.5 mm² AWG 16 7.5 mm3 grooves 2.5 mm² AWG 14 7.5 mmno groove 4.0 mm² AWG 12 7.5 mm
Crimp contact identification
* on the back crimp collar
Use of the coding pin prevents incorrect mating to other connectors of the same type.
The male pin should beomitted from the opposingcavity in the male insert.
13.18
HanQ
Han® Q 17
Features 17 contact chambers taking the control contacts
of the series Han D® (10 A)
Space-saving and compact design
Leading protective ground
Crimp terminal with standard Han D® contacts
Use of standard tools
Insert is suitable for the hoods and housingsof the series Han-Compact®
The contacts can be removed with the aid of aremoval tool from the mating side
Current carrying capacity
The current carrying capacity is limited by maximum temperatureof materials for inserts and contacts including terminals. Thecurrent capacity-curve is valid for continuous, not interruptedcurrent-loaded contacts of connectors when simultaneous poweron all contacts is given, without exceeding the maximum termpe-rature.
Control and test procedures according to DIN IEC 60 512-3.
Wor
king
cur
rent
(A
)
Ambient temperature (C°)
Wire gauge: 0.5 mm2
1.0 mm2
1.5 mm2
Technical characteristicsSpecifications DIN EN 61 984
DIN VDE 0110
Approvals
InsertsNumber of contacts 17 + PE
Electrical dataacc. to DIN EN 61 984 10 A 250 V 4 kV 2
Working currentWorking voltageTesting voltagePollution degree
Working voltageacc. to UL 250 V
Insulation resistance ≥ 1010 ΩMaterial PolycarbonateLimiting temperatures – 40 OC / + 125 OCFlammability acc. to UL 94 V 0Mechanical working life
- mating cycles ≥ 500
ContactsMaterial Copper alloySurface
- hard-silver plated 3 µm Ag- hard-gold plated 2 µm Au over 3 µm Ni
Contact resistanceCrimp terminal < 3 mΩ
- mm² 0.14 - 2.5 mm²- AWG 26 - 14
Plastic hoods/housingsMaterial Polycarbonate RAL 9005Locking element Polyamide Flammability acc. to UL 94 V 0Hood/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 40 050in locked position IP 65Cable gland Pg 16, M 25
Metal hoods/housingsMaterial die cast zinc alloyLocking element V2A steelHoods/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 65
AccessoriesCrimping tools chapter 99
13.19
HanQ
Han® Q 17
20 10 001 3211 20 10 001 3221
09 12 017 3101 F
09 12 017 3001 M
250 V 10 A
Part No.
Identification Male insert (M) Female insert (F) Drawing Dimensions in mm
Inserts
Number of contacts
17
Crimp terminalOrder crimp contactsseparately
Wire gauge Part No.
Identification (mm2) Male contacts Female contacts Drawing Dimensions in mm
Stock items in bold type* partly loaded insert
Crimp contactsHan D® contacts
0.14-0.37 09 15 000 6104 09 15 000 62040.5 09 15 000 6103 09 15 000 6203
silver plated 0.75 09 15 000 6105 09 15 000 62051.0 09 15 000 6102 09 15 000 62021.5 09 15 000 6101 09 15 000 62012.5* 09 15 000 6106 09 15 000 6206
0.14-0.37 09 15 000 6124 09 15 000 62240.5 09 15 000 6123 09 15 000 62230.75 09 15 000 6125 09 15 000 6225
gold plated 1.0 09 15 000 6122 09 15 000 62221.5 09 15 000 6121 09 15 000 62212.5* 09 15 000 6126 09 15 000 6226
StrippingWire gauge ø length
0.14-0.37 mm2 AWG 26-22 0.90 mm 8 mm0.5 mm2 AWG 20 1.10 mm 8 mm0.75 mm2 AWG 18 1.30 mm 8 mm1. mm2 AWG 18 1.45 mm 8 mm1.5 mm2 AWG 16 1.75 mm 8 mm2.5 mm2 AWG 14 2.25 mm 6 mm
FOC contactsfor 1 mm plastic fibre
Contact arrangementView from termination side
13.20
HanQ
Han® Q 4/2
Features Technical characteristics
Current carrying capacity
The current carrying capacity is limited by maximum temperatureof materials for inserts and contacts including terminals. Thecurrent capacity-curve is valid for continuous, not interruptedcurrent-loaded contacts of connectors when simultaneous poweron all contacts is given, without exceeding the maximum termpe-rature.
Control and test procedures according to DIN IEC 60 512-3.
Wor
king
cur
rent
(A
)
Ambient temperature (C°)
Wire gauge 2,5 mm2
4,0 mm2
2 power contacts Han D® 10 A4 signal contacts Han® C 40 A
Leading protective ground
Protection against contact with the fingers acc.IEC 60 529
Insert is suitable for the hoods and housingsof the series Han-Compact® (not suitable for19 12 008 0501, 09 12 008 0301)
The power contacts can be removed with the aidof a removal tool from the termination side
3 coding possibilities by using a coding pin in-stead of the fixing screw
Specifications DIN VDE 0627DIN VDE 0110DIN EN 61 984
Approvals
InsertsNumber of contacts 4/2 + PE
Electrical dataacc. to DIN EN 61 984
Power area 40 A 400/690 V 6 kV 3
Working currentWorking voltageRated impulse voltagePollution degree
Signal area 10 A 250 V 4 kV 3
Working currentWorking voltageRated impulse voltagePollution degree
Working voltageacc. to UL 600/250 V
Insulation resistance ≥ 1010 ΩMaterial PolycarbonateLimiting temperatures – 40 OC / + 125 OCFlammability acc. to UL 94 V 0Mechanical working life
- mating cycles ≥ 500
ContactsMaterial copper alloySurface
- hard-silver plated 3 µm Ag- hard-gold plated 2 µm Au over 3 µm Ni
Contact resistance ≤ 0.3 mΩCrimp terminal
- mm2 1.5 - 6 mm² / 0.14 - 2.5 mm²- AWG 16 - 10 / 26 - 14
Max. insulation- Power contacts ø = 5 mm
Plastic hoods/housingsMaterial Polycarbonate RAL 9005Locking element Polyamide RAL 9005Flammability acc. to UL 94 V 0Hood/Housings seal NBRLimiting temperatures – 40 OC / + 125 OCDegree of protection acc. to DIN EN 60 529in locked position IP 65
AccessoriesCrimping tools chapter 99
13.21
HanQ
Han® Q 4/2
09 12 006 3141 F
09 12 006 3041 M
400/690 V 40 A
Crimp terminalOrder crimp contactsseparately
Part No.
Identification Male insert (M) Female insert (F) Drawing Dimensions in mm
Inserts
Number of contacts
4/2
Wire gauge Part No.
Identification (mm2) Male contacts Female contacts Drawing Dimensions in mm
Stock items in bold type
Crimp contactsHan D® contactsSignal contacts
0.14-0.37 09 15 000 6104 09 15 000 62040.5 09 15 000 6103 09 15 000 6203
silver plated 0.75 09 15 000 6105 09 15 000 62051.0 09 15 000 6102 09 15 000 62021.5 09 15 000 6101 09 15 000 62012.5* 09 15 000 6106 09 15 000 6206
0.14-0.37 09 15 000 6124 09 15 000 62240.5 09 15 000 6123 09 15 000 62230.75 09 15 000 6125 09 15 000 6225
gold plated 1.0 09 15 000 6122 09 15 000 62221.5 09 15 000 6121 09 15 000 62212.5* 09 15 000 6126 09 15 000 6226
StrippingWire gauge ø length
0.14-0.37 mm2 AWG 26-22 0.90 mm 8 mm0.5 mm2 AWG 20 1.10 mm 8 mm0.75 mm2 AWG 18 1.30 mm 8 mm1. mm2 AWG 18 1.45 mm 8 mm1.5 mm2 AWG 16 1.75 mm 8 mm2.5 mm2 AWG 14 2.25 mm 6 mm
Crimp contactsHan C® contactsPower contacts
2.5 09 32 000 6105 09 32 000 6205silver plated 4.0 09 32 000 6107 09 32 000 6207
6.0 09 32 000 6108 09 32 000 6208 StrippingWire gauge ø length
2.5 mm² AWG 14 2.25 9.04.0 mm² AWG 12 2.85 9.66.0 mm² AWG 10 3.50 9.6
Contactarrangement
View from termination side
13.22
HanQ
09 12 008 0527 Pg 16
19 12 008 0501 M 25
09 00 000 5059 Pg 1619 12 000 5157 M 2519 12 000 5158 M 25
19 12 000 5057 M 2519 12 000 5058 M 25
09 12 008 0427 Pg 1619 12 008 0429 M 25
09 00 000 5058 Pg 16
09 12 008 0428 PAFS 18
Stock items in bold type
Hoods/Housings Han-Compact® thermoplastic / metal
Identification Part No. Drawing Dimensions in mm
Hoo
ds
Hoodthermoplastic
Cable glandorder separately
Hoodmetal
Cable glandorder separately
Cable sealthermoplasticfor hoods
Thrust boltand insert
Cable sealthermoplasticfor housings
Thrust boltand insert
Colour SWCable
min. max.Pg 16 11.5 mm 15.5 mmM 25 white 24 10.5 mm 14.0 mmM 25 14.0 mm 17.0 mm
Cable seals
metal
Thrust bolt, insert
10.5 mm 14 mm14.5 mm 17 mm
Cable Ø Cable Ømin. max.
Cab
le Ø
min
.C
able
Ø m
ax.
Hoodthermoplastic
Cable glandorder separately
h g
13 Pg 16
14 M 25x1.5
Hoodthermoplastic
Cable glandorder separately
09 12 008 0327
09 12 008 0301
09 12 008 0727 Pg 1619 12 008 0729 M 25
13.23
HanQ
09 12 008 0902
09 12 008 0901 Pg 16
09 12 008 5407 09 12 008 5408
09 12 000 9912
Hou
sing
s
Housingbulkhead mountingthermoplastic
Housingbulkhead mountingmetal
Housingcable to cablethermoplastic
h g
13 Pg 16
14 M 25x1.5
Stock items in bold type
Hoods/Housings Han-Compact® thermoplastic / metal
Identification Part No. Drawing Dimensions in mm
Identification Part No. Drawing Dimensions in mm
Housingbulkhead mountingthermo-plastic
angled
Housingsurface mountingthermo-plastic
angled
Cable glandorder separately
Cable glandorder separately
for formale insert female insert
without sealing with sealing
Protection coversthermoplastic
GasketHan® Q 8/0
HanQ
13.24
Han-Drive® Application
Worm gear motor used as servodrive with integrated motor connector Han-Drive®
Flender-Himmelwerk GmbH