http://cer.sagepub.com
Concurrent Engineering
DOI: 10.1177/1063293X03038367 2003; 11; 289 Concurrent Engineering
Abdalla Ahmed Al-Ashaab, Karina Rodriguez, Arturo Molina, Mauro Cardenas, Joaquin Aca, Mohammed Saeed and Hassan
Internet-Based Collaborative Design for an Injection-moulding System
http://cer.sagepub.com/cgi/content/abstract/11/4/289 The online version of this article can be found at:
Published by:
http://www.sagepublications.com
can be found at:Concurrent Engineering Additional services and information for
http://cer.sagepub.com/cgi/alerts Email Alerts:
http://cer.sagepub.com/subscriptions Subscriptions:
http://www.sagepub.com/journalsReprints.navReprints:
http://www.sagepub.com/journalsPermissions.navPermissions:
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
CONCURRENT ENGINEERING: Research and Applications
Internet-based Collaborative Design for an Injection-moulding System
Ahmed Al-Ashaab,1,* Karina Rodrıguez,1 Arturo Molina,2 Mauro Cardenas,2
Joaquın Aca,2 Mohammed Saeed3 and Hassan Abdalla4
1School of Engineering and Built Environment, Wolverhampton University, Wulfruna Street,
Wolverhampton, WV1, 1SB, England2Concurrent Engineering Research Group, CSIM/DIA, ITESM Campus Monterrey,
E. Garza Sada Sur 250, C.P. 64849, Monterrey, N.L. Mexico3Department of Computer Science and Information Systems, Chester College of Higher Education,
Parkgate Road,CH1 4BJ, Chester, UK4Department of Design Management and Communications, DeMontfort University, Fletcher Building,
The Gateway, Leicester, UK
Abstract: Nowadays, the globalization of the manufacturing enterprises requires collaboration across frontiers. In order to attain effective
collaboration, the information about the product life cycle must be captured and administrated in a way that supports the decision taken during
the product development. In this context, the manufacturing process information needs to be shared between manufacturers. This paper
introduces the SPEED (Supporting Plastic enginEEring Development) system designed to facilitate the sharing of injection-moulding
information between interested parties via the Internet. Both the architecture and the functionality of the SPEED system are presented and
described in this paper through a case study. The evolving issues are addressed. Finally, closing remarks and conclusions of the system are
presented.
Key Words: design for mouldability, manufacturing model, injection-moulding process information, collaborative product development, design
for manufacturability over internet.
1. Introduction
Global manufacturing is an on-going tendencysupported by advanced information technologies andglobal marketing. Nowadays, it is common to see thatproduct engineering, tooling, manufacturing, and finalassembly of a product are done in companies situated indifferent countries in the world. The different teamsinvolved in the product development have differentexpertise and knowledge that is not shared among them.The lack of interrelated knowledge about all the productlife cycle activities is one of the most common problemsfacing industry in the process of product development.
The collaboration between the distributed teams isdifficult due to the distance and the difference ofperspectives and knowledge used in their activities.This collaboration requires good coordination andadministration of the product life cycle informationand knowledge in order to support the taking of right
engineering decisions. The information technologies andthe Internet can support this need by providing themechanism of capturing and providing knowledge andinformation in real time, secure and in a less expensiveway. These technologies can also provide a solutionfor the collaborative work between different teamssituated physically in different places of the world.The challenge is to allow accessibility to the knowledgeof the product life cycle to all those involved in thedevelopment of a product. The research work tofacilitate the collaboration among the geographicallydistributed companies is called Collaborative ProductDevelopment (CPD) systems [9]. The research presentedin this paper is considered part of this CPD researcheffort.
This paper presents the SPEED (SupportingPlastic enginEErng Development) system designed tofacilitate the sharing of injection-moulding informationand knowledge between interested parties via theInternet. Section 2 presents the activity modeling ofthe injection-moulded product as well as the needfor capturing manufacturing process information.Section 3 presents the injection-modeling processinformation. Sections 4 and 5 describe both the archi-
*Author to whom correspondence should be addressed.E-mail: [email protected]
Volume 11 Number 4 December 2003 2891063-293X/03/04 0289–11 $10.00/0 DOI: 10.1177/1063293X03038367
� 2003 Sage Publications © 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
tecture and the functionality of the SPEED systemthrough a case study. The evolving issues are addressed.Finally, discussion of the results and conclusions of thesystem are presented in Sections 6 and 7.
2. Injection-moulded ProductDevelopment Representation
Prior to developing an effective collaboration betweendistributed teams, it was necessary to determine whichactivities of the product life cycle were going to besupported and the information needed to be captured.Therefore, an activity modeling using IDEF0 techni-ques [5] was performed with several industrial spon-sor companies. Figure 1 shows the key activities of theplastic product development. These are product specif-ication definition, product engineering, mould designand fabrication, and production. The customers’requirements are the input for defining the productspecifications activity which itself will produce thespecification data that controls the product engineeringactivity. The product engineering activity involvesdesigning analysis, optimizing, testing, and validationactivities to engineer a product that meets the customers’needs. There are many commercial CAD/CAE toolsthat could be used to support these activities butthey lack the knowledge required to support takingthe right engineering decisions. The designers andengineers themselves take decisions depending on
their personal experiences. The lack of captured knowl-edge related to the injection-moulding process andresources capabilities is a common problem in theplastic industry, as some decisions taken in this stageimpact other downstream activities, mainly mouldfabrication and the production of the plastic part.
Each of these activities provides information that isused by other activities to support intelligent decisionmaking. Time and effort could be saved if the requiredinformation is provided in the correct time and place.This information represents the experiences gained bythe engineers in different departments as well as thecapabilities of the manufacturing resources used in theproduction area. We call this ‘‘Manufacturing ProcessInformation’’ and is not yet captured and used by anysystem [9].
The following sections present the modeling ofthe injection-moulding process information and itsdevelopment in the SPEED system to support thecollaborative product development.
3. Injection-moulding ProcessInformation Representation
The manufacturing process information needs to becaptured and shared with all those involved in thedifferent activities of the product life cycle. Beforecapturing this information in the software system, aformal method to represent it is needed. In this work the
Figure 1. Key activities in plastic product development.
290 A. AL-ASHAAB ET AL.
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
EXPRESS-G [7] has been used for the informationmodeling [1]. There are three key activities involved inthe development of injected moulded parts: productengineering, the mould engineering and the production.As such, knowledge of plastic part mouldability(manufacturability), mould design and fabrication andinjection-moulding machine capabilities is required tosupport the engineering applications. This knowledgeis represented in a Manufacturing Model [1], whichis an information model to capture and represent themanufacturing process information (process and resou-rces capabilities). This is used as a common source ofinformation to ensure manufacturing data integritybetween the interacting design and manufacturingactivities. Hence, the Manufacturing Model of thiswork was divided into three hierarchical trees, theyare: Mouldability Features, Injection-mould Elements,and Injection-moulding Machine Elements as illustratedin Figure 2. The injection moulding process infor-mation was obtained from literature [2,3,6,8] and datacollected from the plastic industry, especially thecosponsors of the SPEED project. The manufacturingdata integrity was achieved by:
. Capturing and representing the details of datadefinition including the constraints imposed on thedata.
. Capturing the interaction between objects in the samehierarchical tree.
. Capturing the interaction between objects in differenthierarchical trees.
The following sections present in some detail themodeling of the injection-moulded features. Also a casestudy is used to explain their implementation in theSPEED system.
3.1 Representing the MouldabilityFeatures Knowledge
To explore the representation of the mouldabilityknowledge related to the injection-moulding process,a features-based approach has been adopted and calledMouldability Features. Such features are wall, reinforce-ments (rib, boss, and web), hole, corner shape, partingline, weld line, gate position, and ejection position. Eachfeature was represented as an object that is defined byseveral attributes. Mouldability constraints of eachattribute and their interactions with other features werecaptured to ensure the manufacturability of the plasticpart. The wall and rib features are presented in somedetail in the following subsections in order to demon-strate the knowledge structure.
3.1.1 REPRESENTING THE MOULDABILITY OFA WALL FEATURE
One of the characteristics of the injection-mouldingprocess is that it is only possible to produce thin-walledproducts. The length and the thickness of the walls
Mouldability Mouldability
FeatureFeature
WallWall
Pris maticWall
Rotational Wall
Transition Wall
Wall with angle
Curved Wall
ReinforcementReinforcement
Rib
Boss
Web
HoleHole
Blind Ho le
Corner Corner ShapeShape
PartingParting LineLine
WeWe ld LiLi ne
GaGa te PoPo s ition
EjEj ection PoPo s ition
PlasticPlasticProductProduct
has is moulded by
is p
rodu
ced
by
Clamping
Unit
Injection
Unit
Injection Injection
Moulding Moulding
MachineMachine
Subsurface Gate
CoCo r e CavityCavity
Ventnt in g g SySy s tem
CoCo oling SySy s tem
EjEj ection SySy s tem
SpSp r ue
G ating ng SySy s tem
RuRu n ner SySy s tem
FeFe e d SySy s tem
Pin
Conventional Pin
Two-Step Pin
Three-Step Pin
Sleeve Pin
Gate
Tab Gate
Overlap Gate
Fan Gate
Winkle Gate
Sprue Gate
Ring Gate
Diaphram Gate
Film Gate
Pin Gate
Round Edge Gate
Rectangular Edge Gate
Air Ejector
Blade Ejector
Stripper Bar Ejector
Stripper Ring Ejector
Stripper Plate Ejector
Valve Ejector
Injection Injection Mould Mould
ElementsElements
Figure 2. Injection-moulding ‘‘Manufacturing Model’’ representation.
Collaborative Design for an Injection-moulding System 291
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
need to have the recommended values by the materialprovider as a reference point. The wall can be consideredas the main feature of a plastic product, where otherfeatures (e.g. ribs, bosses, holes, etc.) are going to beplaced on. Therefore, the mouldability of these featuresdepends on the wall in which these are put on.Figure 3 illustrates the wall attributes that must be
considered to ensure the manufacturability of the plasticpart. These are:
. Direction and position to define its position within theplastic part. This will effect the definition of otherfeatures as well as to detect intersection with otherwall features.
. Thickness: too thick a wall causes mouldabilityproblems like sink marks, shrinkage, and bending;too thin a wall causes short shot problems. Typicalthickness is 1–5mm.
. Length and width related to the thickness. The thickerthe wall, the longer they could be.
. Draft angle: it is important to facilitate ejecting thepart from the mould.
. Maximum load position helps to determine thesuitable rib position for rigidity.
3.1.2 REPRESENTING THE MOULDABILITY OFA RIB FEATURERibs are commonly used to give strength and rigidity
to the plastic product. At the same time, ribs help to
have thinner walls and therefore reduce the amount ofmaterial and later the cooling time. To prevent ribmouldability problems, mainly the sink mark and shortshot, its design must consider the wall thickness onwhich it is placed. Figure 3 illustrates the rib attributesand their interactions with the wall feature, which mustbe considered to ensure the manufacturability of theplastic part. These are:
. Direction and position effect other features definitionand help to detect possible intersection among theribs. Ribs should be placed where the maximum loadis expected on the wall.
. Height and width: key rib’s attributes that must beconsidered carefully to avoid sink marks that mayappear due to the thick material section. On the otherhand, too high a rib makes it harder to manufacturethe mould and to fill it with material during theprocessing, especially if the width is also too small.The rules for the maximum permitted height andwidth are:
Rib_height¼ (3�Wall_thickness)þ 0.85Rib_width¼ 2/3�Wall_thickness
. Draft angle: it is important to facilitate ejecting thepart from the mould.
. Base radius: to prevent stress concentrations.
. Distance between ribs: to allow easy flow ofmaterial.
Mouldability Features
Weld Line
Parting Line
Hole
Ejection Position
Reinforcement
Blind Hole
RiRibPrismatic
Wall
Rotational Wall
Gate Position
REAL
INTEGER
REAL
REAL
BOOLEAN
REAL
INTEGER
Web
attached_on_wall
NoR
ein
heightwidth
distanceReinuse_rib
thicknesslength
draft_angle
max_load_position
radi
usou
tsid
e_co
rner
_rad
ius
stre
ss_c
onst
_rad
ius
desi
red_
min
_rad
ius
gated_wallconnect_wall1connect_wall2
NoGate
rein_wall
base
_fil
let
Corner Shape
blin
d_ho
le_w
all_
angl
e
dept
h
diam
eter
dist
ance
_wal
ldi
stan
ce_h
ole
leng
th
caus
ed_b
y_ho
le
Transition Wall
dire
ctio
npo
siti
on
width
base
_rad
ius
draf
t_an
gle
WalWall
Boss
Figure 3. Representation of the mouldability features.
292 A. AL-ASHAAB ET AL.
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
3.1.3 REPRESENTING THE OTHERMOULDABILITY FEATURES
A similar modeling technique was performed on therest of the mouldability features, which are modeled inEXPRESS-G shown in Figure 3. The figure shows theMouldability Feature abstract class, which puts theONE OF constraint on its subentities of Wall,Reinforcement, Hole, Corner Shape, Weld Line,Parting Line, Ejection, and Gate Position. Each ofthese features has attributes and constraints captured toavoid mouldability problems.
4. The SPEED System Architecture
SPEED (Supporting Plastic enginEEring Develop-ment) is a prototype system that supports the need ofcapturing and sharing the injection-moulding processand resources capabilities over the Internet. It aids theintegrated product development by ensuring the provi-sion of the right manufacturing process information atthe right time and place.
SPEED is a Web-based system that uses theInternet and object-oriented database technologies.These technologies provide an easy and effective wayto distribute the manufacturing process informationalong the companies in the extended enterprise. Thesystem was developed using Java and Object StoreOODBMS in order to provide an efficient retrievalof the data and management of the manufacturinginformation. The Manufacturing Model was capturedin an object-oriented database according to the repre-sentation explained in the previous section. Thisdatabase resides on a Silicon Graphics server, which
also works as a web server. Currently, the access to theweb server is restricted for internal testing due tosecurity reasons. The engineering applications accessand use the Manufacturing Model informationthrough the WWW. This system architecture is illustra-ted in Figure 4(a), while Figure 4(b) shows the SPEEDsystem’s main page. There are three engineering decisionsupport applications so far. They are: the design formouldability of the plastic part, the selection of theproduction equipment and the supporting of the moulddesign.
5. Injection-moulded Product Development inSPEED: A Case Study
To give a detailed description of the SPEED func-tionality, the plastic part shown in Figure 5 is used asa case study. Only the ‘‘design for mouldability’’application is presented.
5.1 The SPEED Design for MouldabilityApplication
The ‘‘design for mouldability’’ application is con-cerned with ensuring that product functional featurescan be moulded without problems. The applicationalso provides feedback advice to the designer regardingthe design issue under consideration. This applicationis supported by the mouldability features repre-sentation in the Manufacturing Model. Moreover, dueto the interaction between the data, the impacts of the
Figure 4. The SPEED system.
Collaborative Design for an Injection-moulding System 293
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
product manufacturability on the injection mould andmachine are considered and highlighted in the SPEEDsystem.The ‘‘design for mouldability’’ application window
is as shown in Figure 6. The user needs to input
the product general information, as illustrated inFigure 5-A. As previously explained, the SPEEDsystem uses the design-by-feature approach. In thefollowing subsections some of the features of the casestudy product will be outlined in detail.
Side wall
Rib
Web
Holes
Boss
Base wall D
D = boss diameter
d
d
d = hole diameter
2*t
2*t
2*t
2*t
2*t
t = base wall thickness
General description: Thin wall productMaximum length: 600 mmMaximum width: 400 mmMaximum depth: 100 mmWeight: 0.5 kgPlastic: Polyethylene (HD)Texture: Smooth
300 mm
200 mm
400 mm
600 mm
-A-
-B- -C-
70 mm
50 mm
50
Figure 5. SPEED Case study. -A- Case study general description in 2D; -B- Design for function; -C- Design for mouldability.
Figure 6. Defining the base wall feature in SPEED. A – Moudability features menu; B – Feedback advice to the user, C – 2D illustration drawing;D – Product information input values; E – OK Button.
294 A. AL-ASHAAB ET AL.
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
5.1.1 DESIGN FOR MOULDABILITY OF AWALL FEATURE
To start defining the product, the first feature thatmust be considered is the wall feature. The features areselected by pressing the buttons on the top of theapplication and are defined by filling in the fields onthe right hand side of the screen. Figure 6 shows the‘‘BaseWall’’ definition. The values required for thewall are direction, length, width, thickness, draft angle,initial position, and applied force position. Those arethe attributes captured in the wall object as explainedin Section 3.1.1. The SPEED system checks their valuesagainst the constraints captured in the ManufacturingModel and sends an advice to the user in the feedbacksection.
In the case of the ‘‘BaseWall’’, the thickness has beendefined as 13mm for the sake of the case study. TheSPEED sends a feedback advising to make a thinnerwall (and consequently add a rib) with the value of‘‘3.5mm’’ which is the recommendation of the plasticmaterial selected by the designer of the part underconsideration. The direction of the wall is used todetermine if the wall needs a draft angle, in this case,a draft angle is not needed, as the direction isperpendicular to the opening axis of the injectionmachine. The applied force position is used to suggestwhere the rib should be placed in order to give therequired stiffness. The user interacts with the systemto modify the values as it was advised. Finally, bypressing ‘‘OK’’ the ‘‘Base Wall’’ definition is rechecked.If the data falls within the mouldability constraint the
wall is created as part of the plastic product definition,which is represented in an object.
5.1.2 DESIGN FOR MOULDABILITY OF ARIB FEATURE
In order to have the same wall rigidity, as in theoriginal design, a rib feature will be needed. It will becreated automatically by the SPEED system. SPEEDmakes all the calculations of the rib attributes that are de-fined in the manufacturing model (refer to Section 3.1.2)considering the constraint applied to each attribute. Therib values are shown as default values in Figure 7.The position of the rib, also by default, will be wherethe maximum load is expected on the wall feature. Thisshould have been defined in the wall session, otherwiseit would be considered in the center of the wall. TheSPEED system user will have the freedom to change anyvalue registered and checked by the system to evaluatewhether they are within the mouldability constraint ofthe process. For the sake of argument and demonstra-tion, the rib attributes have been changed to some valuesout of the limit of the injection-moulding process.SPEED will make the evaluation and send a feedbackadvice to the user with the recommended values asillustrated in Figure 7. On the other hand, if there are noproblems, the system will simply inform and allow theuser to continue defining the product. In the case ofthe rib, the system suggests to add another rib toreinforce the rigidity of the product. This is done byselecting the rib feature from the menu and changingor accepting the default values.
Figure 7. System suggestion when adding a rib.
Collaborative Design for an Injection-moulding System 295
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
5.1.3 DESIGN FOR MOULDABILITY OFOTHER FEATURES IN SPEEDA similar procedure is followed with the rest of the
features until the product is within the mouldabilityconstraints as shown in Figure 5-C. The Design forMouldability application is flexible regarding thefeatures definition and their interactions. Its detaileddescription lays beyond the scope and the space limita-tion of this paper. As shown in Figure 8, every time a newfeature is created, the system draws a simple repre-sentation of each feature in 2D. This basic representationhelps to have an idea of the product being constructed.
6. Discussion of the SPEED Results
In the world of integrated marketing, the globalmanufacturing collaboration is essential in order tosustain and improve the market share. However, theeffectiveness of such collaboration depends on theavailability and the management of informationand knowledge required through product development.The SPEED system is a prototype that supports thiscollaboration. This is because it is an Internet knowl-edge-based information system where the processknowledge is represented in detail to support andensure that right engineering decisions are taken. Theuse of the Internet makes the information availableat any time and place and in a format easy to use
and understand. The system architecture supports thesimultaneous use of the system by many users, whocould be distributed geographically, in real time. TheSPEED system provides the users with a mechanismwhere products, mould, and machine information couldbe seen at any time during the development process.For example pressing the ‘‘Product Information’’ button(as shown in Figures 6–8) brings a window with thedetailed definition of the product in that stage. This isone means of collaboration by sharing the informationthroughout the development process. In addition,further research is being conducted in order to includevideo and audio communication tools that make moreeffective the real time interaction among the geographi-cally distributed team members.
The SPEED has been tested and presented throughdemonstration several times with the Mexican andBritish plastic industries. Their feedback has beenfocused on two main issues, support 3D drawing andthe cost application. The Java 3D has been testedand has already been integrated into the system. Inaddition, while the system supports the developmentof complex injection-moulded parts at certain extent;more work is required to represent the complexgeometry of such part. Furthermore, a mechanism tointegrate CAD to the system is an issue that needsto be addressed. The commercial advances in whatis called Collaborative Product Commerce systems,i.e., OneSpace Collaboration [4], are promising for
DESIGN FOR MOULDABILITY
Home Product Information Plastic Information Load a product Help
Ejection PinGate PositionWeld LineParting LineCorner ShapeChannelHole Rib Prismatic Wall
----------BaseWall SPEED_Test
Product Drawing
Y
Z
Y
X
Web
Name:
Length (mm):
Base radius (mm):
Thickness (mm):
Draft Angle:
Height (mm)
Initial pos. (X,Y,Z):
Web2
5
0.5
2
1
11
(0,80,0)
OK Clear All
Feedback
***CONFIRM***
The Web2 is within the mouldability constraint
Web2 HAS BEEN CREATED
You can continue defining other features
The Web2 is within the mouldability constraint
Web2 HAS BEEN CREATED
You can continue defining other features
Figure 8. Product graphic representation in SPEED.
296 A. AL-ASHAAB ET AL.
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
addressing this issue. The cost application is wellunderstood by the research team and it is a questionof time to develop it and integrate to the system.
An approach, such as the SPEED system, will helpthe plastic industry to capture their knowledge andexperiences and then acts as an intellectual propertysystem. This could be considered feasible amongthe partners of one industrial group, who are boundedby common financial interests. However, sharing theknow-how knowledge among the subcontractors is anissue that needs to be addressed from the managementpoint of view.
7. Conclusions
SPEED is an information system based on theInternet, which supports the integrated injection-moulding product development. This research projectproves that the mouldability rules of the featuresof a product and its knowledge involved can becaptured and shared through the Internet to supportthe global manufacturing collaboration.
The use of the ‘‘design for mouldability’’ applicationcan be customized in accordance with user requirements.The features presented in this work are common to allplastic products; this allows the definition of a greatvariety of products no matter the complexity of thegeometry. The manufacturing process information wasobtained from the existing literature about the injection-moulding process [2,3,6,8]. Each plastic company uses itsown variations of rules based on the experience of itsdesigners and other engineers. Because of these, beforemaking the technology transfer to an industry, acustomised process is required to capture the newknowledge and adapt it to the specific company’srequirements. The structure of the information can beapplied to different kinds of manufacturing processes,such as casting. This capability allows the application ofthis concept to another industry.
SPEED stimulates collaboration between interna-tional companies, where for instance product engi-neering is taking place in the USA, Europe, or Japanwhile the manufacturing is carried out in Mexico. Thissupports the production of a better, cost effectiveproduct in less time. Hence, the SPEED systemensures the integration and collaboration among thegeographically distributed companies.
Acknowledgment
The Carplastic, VITRO Ensers Domestico, Ponds,The British Council office Mexico City, and the CSIMof the ITESM Campus Monterrey have sponsoredthis work in Mexico. Metadata and Excelon have
provided the database ObjectStore. The Engineeringdivision of Wolverhampton University sponsors thePhD scholarship of Miss Karina Rodriguez. Theauthors wish to acknowledge the sponsors for theirsupport.
References
1. Al-Ashaab, A.H.S and Young, R.I.Y. (1997). ModellingManufacturing Process Information using the ExpressLanguage. The Special Issue of Concurrent EngineeringResearch and Application Journal ‘‘CERA’’ on EnterpriseIntegration and Management.
2. Berins, M.L. (ed.) (1991). Plastic Engineering Handbook,Van Nostrand Reinhold, New York.
3. Bralla, J.G. (1986). Handbook of Product Design forManufacturing, McGraw-Hill Inc, New York.
4. Cocreate 2003, http://www2.cocreate.com/
5. Coloquhun, G.J., Baines, R.W. and Crossley, R. (1993).A State of the Art Review of IDEF0, International Journalof Computer Integrated Manufacture, 6(4): 252–264.
6. Dym, J.B. (1987). Injection Molds and Molding, A PracticalManual, Van Nostrand Reinhold Company, New York,ISBN 0-442-21785-4.
7. EXPRESS 1992. EXPRESS Language Reference Manual,ISO DIS 10303-11.
8. Pye, R.G.W. (1989). Injection Mould Design, LongmanScientific & Technical, EU.
9. Rodriguez, K. and Al-Ashaab, A. (2002). A review ofInternet based collaborative product development systems.In: Proceedings of 9th ISPE International Conference onConcurrent Engineering: Research and Applications,Cranfield, UK.
Dr. Ahmed Al-Ashaab
Dr. Ahmed Al-Ashaab is aSenior Lecturer in the Schoolof Engineering and Built Envir-onment in the University ofWolverhampton. Ahmed obtai-ned his PhD from Loughbor-ough University in 1994. Sincethen he has worked in theITESM Campus Monterrey inMexico where 50% of histime was spent working withMexican Industry. He has been
active in introducing and implementing NPI/D meth-odologies based on Concurrent Engineering within theMexican manufacturing companies. He is the Founderand was the President of the Mexican Society ofConcurrent Engineering. He is the leader of on goingproject of Internet-based Intelligent Information systemto support the plastic product development. His researchinterests are CE, Knowledge-based Engineering,Extended and Virtual Enterprises and Collaborative
Collaborative Design for an Injection-moulding System 297
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
Product Development. Dr. Al-Ashaab has written manyinternational publications and participated in severalof the conference committees and session chair.Dr. Al-Ashaab is the publicity chair of the ISPE/CE2xxx Series Conferences.
Karina Rodriguez
Karina Rodriguez is a PhDstudent in the School of Engi-neering and Built Environmentin the Wolverhampton Univer-sity. She got a Computer Sci-ence honours degree from theITESM Campus Monterrey inMexico in 1999. She workedas Research Assistant in theCSIM of ITESM campusMonterrey in the SPEED proj-ect. Her research interests are
Knowledge-based Engineering, Information Modelingand Internet-based Collaborative Product Development.
Dr. Arturo Molina
Dr. Arturo Molina is TitularProfessor in the CSIM-ITESMCampus Monterrey. Arturoobtained his PhD fromLoughborough University in1995. His research Interestsare CE, Knowledge-basedEngineering, Virtual Enter-prises and Enterprise Model-ing. He was coordinatingseveral international projectsin the area of virtual enterprise.Dr. Molina has written manyinternational publications and
participated in several conference committees andsession chair.
Mauro Cardenas
Mauro Cardenas graduatedfrom Mechanical and ElectricalEngineering from the ITESMCampus Monterrey in 2001.He worked in the SPEEDproject for 2 years. He hasjoined the Mabe GE Plasticas product design engineer.His research interests areCE, CAD/CAM/CAE andInternet-based CollaborativeProduct Development.
Joaquın Aca
Joaquın Aca, graduatedfrom Mechanical and Electri-cal Engineering from theITESM Campus Monterreyin 2000. He is currentlydoing his Masters in AdvanceManufacturing System inCSIM ITESM Campus Mon-terrey. He has been workingin several Knowledge-basedEngineering projects withthe Mexican Industry. Hisresearch interests are CEand KBE.
Dr. Mohammed Saeed
Dr. Mohammed Saeed is aSenior Lecturer in ComputerScience & Information SystemsDepartment of the ChesterCollege of Higher Educationin the. He got his PhD inComputer Science fromLoughborough University in1992. His research interest areInformation System, ObjectOriented Methodologies andInternet-based CollaborativeProduct Development.
Professor Hassan Abdalla
Professor Hassan Abdalla iscurrently the Head of Depart-ment of Design Managementand Communication at DeMontfort University in theUK and a leading authorityin the field of rapid andsustainable product devel-opment, concurrent engi-neering, and design forassembly/dis-assembly. Thefounder of the rapid productdevelopment research group
at De Montfort University Leicester which has a highreputation, both on a national and an internationallevel. It has very strong links with a numberof organisations and institutions world-wide. Fora number of years, Professor Abdalla worked in
298 A. AL-ASHAAB ET AL.
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from
industry before joining academia. He is the author/co-author of more than 80 research papers publishedin international journals and refereed conferences.He has been invited as a keynote speaker forseveral conferences and currently serving on the
technical reviewing committees of a numberof journals. Professor Abdalla has led severalnational and international funded projects, fromboth the Commission of the European Union andEPSRC.
Collaborative Design for an Injection-moulding System 299
© 2003 SAGE Publications. All rights reserved. Not for commercial use or unauthorized distribution. at PENNSYLVANIA STATE UNIV on April 14, 2008 http://cer.sagepub.comDownloaded from