Chapter 19
Electric Potential Energy
and Electric Potential
AP Learning ObjectivesELECTRICITY AND MAGNETISM Electrostatics
• Electric field and electric potential (including point charges)
• Students should understand the concept of electric field, so they can:
• Define it in terms of the force on a test charge.
• Describe and calculate the electric field of a single point charge.
• Calculate the magnitude and direction of the electric field produced by two or more point charges.
• Calculate the magnitude and direction of the force on a positive or negative charge placed in a specified field.
• Interpret an electric field diagram.
• Analyze the motion of a particle of specified charge and mass in a uniform electric field.
AP Learning Objectives• Students should understand the concept of electric potential,
so they can:• Determine the electric potential in the vicinity of one or
more point charges.• Calculate the electrical work done on a charge or use
conservation of energy to determine the speed of a charge that moves through a specified potential difference.
• Determine the direction and approximate magnitude of the electric field at various positions given a sketch of equipotentials.
• Calculate the potential difference between two points in a uniform electric field, and state which point is at the higher potential.
• Calculate how much work is required to move a test charge from one location to another in the field of fixed point charges.
• Calculate the electrostatic potential energy of a system of two or more point charges, and calculate how much work is required to establish the charge system.
Table of Contents
1. Potential Energy
2. The Electric Potential Difference
3. The Electric Potential Difference Created by Point
Charges
4. Equipotential Surfaces and Their Relation to the electric
Field
5. Capacitors and Dielectrics
6. Biomedical Applications of Electric Potential Differences
(AP?)
Chapter 19:Electric Potential Energy
and Electric Potential
Section 1:
Potential Energy
From Gravity
• Energy based on position
• Change in position
• Change in Energy
• Work
2
2
1vmhmg
Potential Energy
BAAB mghmghW
Electrical Potential Energy Same Effect for Electric Force Energy present based on position
• Change in position
• Change in Energy
• Remember, unless otherwise stated, test charge is positive
FdU E 2
21
4
1
r
qqF
oE
rr
qqU
oE
221
4
1
r
qqU
oE
21
4
1
19.1.1. Two electrons are separated by a distance R. If the distance between the charges is increased to 2R, what happens to the total electric potential energy of the system?
a) The total electric potential energy of the system would increase to four times its initial value.
b) The total electric potential energy of the system would increase to two times its initial value.
c) The total electric potential energy of the system would remain the same.
d) The total electric potential energy of the system would decrease to one half its initial value.
e) The total electric potential energy of the system would decrease to one fourth its initial value.
19.1.2. The electric potential energy for two positive charges of magnitude q and separated by a distance r is EPE1. What will the electric potential energy be if one of the charges is completely removed and replaced by a negative charge of the same magnitude?
a) U2 = 2 U1
b) U2 = U1
c) U2 = U1
d) U2 = 2 U1
e) There is no way to determine this without knowing the value of q.
Chapter 19:Electric Potential Energy
and Electric Potential
Section 2:
The Electric Potential Difference
Electric Potential
Electric Potential is hard to
understand, but easy to
measure.
The potential energy per unit
charge
Related to electric potential
energy and the electric field
Commonly called “Voltage”
Measured in volts (1V = 1 J/C)
The electric potential at a given point is the electric potential energy of a small test charge divided by the charge itself:
SI Unit of Electric Potential: joule/coulomb = volt (V)
o
AB
o
A
o
BAB q
W
qqVV
UU
o
AB
o q
W
qV
U
DEFINITION OF ELECTRIC POTENTIAL
o
E
q
UV
Example 1 Work, Potential Energy, and Electric Potential
The work done by the electric force as the test charge (+2.0x10-6C) moves from A toB is +5.0x10-5J.Find the difference in EPE between thesepoints.Determine the potential difference betweenthese points.
BAABW UU
o
AB
o
A
o
B
q
W
qqV
UU
ABW
C102.0
J100.56-
5
V
J100.5 5(a)
(b)
V 25
Conceptual Example 2 The Accelerations of Positive and Negative Charges
A positive test charge is released from A and accelerates towards B. Uponreaching B, the test charge continues to accelerate toward C. Assuming thatonly motion along the line is possible, what will a negative test charge do whenreleased from rest at B?
Negative charge will accelerate towards A
A positive charge accelerates from a region of higher electric potentialtoward a region of lower electric potential.
A negative charge accelerates from a region of lower potential towarda region of higher potential.
Explanation
We now include electric potential energy as part of the total energy that an object can have:
EUkxmghImvE 2212
212
21
One electron volt is the magnitude of the amount by which the potentialenergy of an electron changes when the electron moves through a potentialdifference of one volt.
V1060.1eV 1 19
Energy Conservation
Example 4 The Conservation of Energy
A particle has a mass of 1.8x10-5kg and a charge of +3.0x10-5C. It is released from point A and accelerates horizontally until it reaches point B. The only force acting on the particle is the electric force, and the electric potential at A is 25V greater than at B. (a) What is the speed of the particle at point B? (b) If the same particle had a negative charge and were released from point B, what would be its speed at A?
AABB UmvUmv 2212
21
BAB UUmv 221
BAoB VVqmv 221
qVU
kg108.1V 25C100.32 55 Bv
mVVqv BAoB 2
sm1.9BvPart b) same speed, opposite direction
19.2.1. Which one of the following statements best explains why it is possible to define an electrostatic potential in a region of space that contains an electrostatic field?
a) The work required to bring two charges together is independent of the path taken.
b) A positive charge will gain kinetic energy as it approaches a negative charge.
c) Like charges repel one another and unlike charges attract one another.
d) Work must be done to bring two positive charges closer together.
e) A negative charge will gain kinetic energy as it moves away from another negative charge.
19.2.2. Four point charges are individually brought from infinity and placed at the corners of a square as shown in the figure. Each charge has the identical value +Q. The length of the diagonal of the square is 2a. What is the electric potential at P, the center of the square?
a)
b)
c) zero volts
d)
e)
a
kQ
4
a
kQ
a
kQ2
a
kQ4
Chapter 19:Electric Potential Energy
and Electric Potential
Section 3:
The Electric Potential Difference Created by Point Charges
Difference in Potential What is the potential difference
as a particle moves in an Electric Field
• due to the electric force as the point charge moves from A to B
Since the force is a function of distance must use calculus:
drr
kqqW
B
A
r
r
o2
B
A
r
r
o r
drkqqW
2
B
o
A
o
r
kqq
r
kqq
o
AB
q
WV
Total Potential of All point charges
i i
i
r
qkV
Difference in Potential
xx
dx 12
B
A
r
r
o r
drkqqW
2
WU
oq
UV
BA r
kq
r
kq
Example 5 The Potential of a Point ChargeUsing a zero reference potential at infinity,determine the amount by which a point chargeof 4.0x10-8C alters the electric potential at a spot 1.2m away when the charge is (a) positive and (b) negative.
r
kqV
(a)
(b)
V 300V
m 2.1
C100.4CmN1099.8 8229 V
V 300V
Example 6 The Total Electric PotentialAt locations A and B, find the total electric potential.
m 60.0
C100.8CmN1099.8
m 20.0
C100.8CmN1099.8 82298229
AV
m 40.0
C100.8CmN1099.8
m 40.0
C100.8CmN1099.8 82298229
BV
i i
i
r
qkV
V 240
V 0
Conceptual Example 7 Where is the Potential Zero?Two point charges are fixed in place. The positive charge is +2q and thenegative charge is –q. On the line that passes through the charges, how many places are there at which the total potential is zero?
19.3.1. Consider the four arrangements of three point charges. Rank the values of the total electric potential at point P in each case in descending order (with the largest first).
a) VA > VD > VC > VB
b) VC > VB > VD > VA
c) VC > VD > VA > VB
d) VB > VC > VB > VA
e) VD > VB > VA > VC
19.3.2. Two point charges lie along the x axis. One charge, located at the origin, has a magnitude +2q. The other charge of unknown magnitude and sign is located at x = 5 units. If the electric potential at x = 4 units is equal to zero volts, what is the magnitude and sign of the second point charge?
a) q/2
b) q/4
c) 2q
d) +q/2
e) +2q
Chapter 19:Electric Potential Energy
and Electric Potential
Section 4:
Equipotential Difference Created by Point Charges
r
kqV
Equipotential Surfaces An equipotential surface
is a surface on which the electric potential is the same everywhere.
The net electric force does no work on a charge as it moves on an equipotential surface.
Electric Field and Equipotential Surfaces
The electric field created by
any charge or group of
charges is everywhere
perpendicular to the
associated equipotential
surfaces and points in the
direction of decreasing
potential.
Equipotential Surfaces and Their Relation to the Electric Field
d
VEavg
In Parallel Plate Capacitors
d
Example 9 The Electric Field and PotentialAre RelatedThe plates of the capacitor are separated bya distance of 0.032 m, and the potential differencebetween them is VB-VA=-64V. Between thetwo equipotential surfaces shown in color, thereis a potential difference of -3.0V. Find the spacingbetween the two colored surfaces.
ABd
VE
E
Vd
m 0.032
V 64 mV100.2 3
mV100.2
V 0.33
m105.1 3
dAB
19.4.1. A proton is moved from point B to point A in an electric field as shown. As a result of its movement, its potential increases to V. If three protons are moved from point B to A, how much will the electric potential of the protons increase?
a) V/9
b) V/3
c) V
d) 3V
e) 9V
19.4.2. Which one of the following statements concerning electrostatic situations is false?
a) No work is required to move a charge along an equipotential surface.
b) If the electric potential with a region of space is zero volts, the electric field within that region must also be zero V/m.
c) If a charge is moved along an equipotential surface, there is no component of the force acting along the charges’ path.
d) The electric field is always perpendicular to equipotential surfaces.
e) The electric field is zero V/m everywhere inside a conductor.
19.4.3. The drawing shows three point charges of equal magnitude, but one is positive (shown in blue) and two are negative (shown in yellow). Some of the equipotential lines surrounding these charges are shown and five are labeled using letters A, B, C, D, and E. At which of the labeled points will an electron have the greatest electric potential energy?
a) A
b) B
c) C
d) D
e) E
19.4.4. The drawing shows three point charges of equal magnitude, but one is positive (shown in blue) and two are negative (shown in yellow). Some of the equipotential lines surrounding these charges are shown and five are labeled using letters A, B, C, D, and E. What is the direction of the electric field at the location of the letter “D?”
a) perpendicular to the equipotential line marked “D” and directed toward the negative charge closest to it
b) parallel to the equipotential line marked “D” and directed toward the location of the letter “C”
c) perpendicular to the equipotential line marked “D” and directed toward the location of the letter “A”
d) toward the negative charge in the lower part of the drawing
e) toward the positive charge
Chapter 19:Electric Potential Energy
and Electric Potential
Section 5:
Capacitors & Dielectrics
Capacitors
A capacitor is a device that can store potential energy
Usually they are build by placing two conductors near
each other, without touching
For AP, we will only look at air separating the two plates
• We can make capacitors with other insulators
separating the two conductors.
Capacitors and Dielectrics
A parallel plate capacitor consists
of two metal plates, one carrying
charge +q and the other carrying
charge –q.
It is common to fill the region
between the plates with an
electrically insulating substance
called a dielectric.
The magnitude of the charge in each place of the capacitor is directly proportional to the magnitude of the potential difference between the plates.
The capacitance C is the proportionality constant.
SI Unit of Capacitance:
coulomb/volt = farad (F)
VQ
THE RELATION BETWEEN CHARGE AND POTENTIAL DIFFERENCE FOR A CAPACITOR
V
QC
CVQ
Capacitance To determine the capacitance, we
must look at how easily the charge can flow between the plates
We will assume that air has the same permittivity as a vacuum
d
AC o
ENERGY STORAGE IN A CAPACITOR
The energy stored on a capacitor can be
expressed in terms of the work done by the
battery.
Voltage represents energy per unit charge,
• so the work to move a charge element dq
from the negative plate to the positive
plate is equal to V dq,
• where V is the voltage on the
capacitor.
The voltage V is proportional to the amount
of charge which is already on the capacitor.
WdU
dqC
qdU
VdqdU
ENERGY STORAGE IN A CAPACITOR
If Q is the amount of charge stored when the whole battery voltage appears across the capacitor, then the stored energy is obtained from the integral:
Since Q=CV, we can rewrite this expression:
Q
C dqC
qU
0 C
Q2
2
1
2
2
1
2
1CVQVUC
Q
dqqC 0
1
19.5.1. An electrical outlet has two vertical slots and a hole into which a three prong plug may be inserted. The maximum potential difference between the two vertical slots is 120 volts. The hole is connected to earth ground. Estimate the maximum electric field that exists between the two vertical slots.
a) 240 V/m
b) 4800 V/m
c) 9200 V/m
d) 120 V/m
e) 6300 V/m
19.5.2. The plates of an isolated parallel plate capacitor with a capacitance C carry a charge Q. What is the capacitance of the capacitor if the charge is increased to 4Q?
a) C/2
b) C/4
c) 4C
d) 2C
e) C
19.5.3. A parallel plate capacitor with plates of area A and plate separation d is charged so that the potential difference between its plates is V. If the capacitor is then isolated and its plate separation is increased to 2d, what is the potential difference between the plates?
a) 4V
b) 2V
c) V
d) 0.5V
e) 0.25V
19.5.4. The plates of an isolated parallel plate capacitor with a capacitance C carry a charge Q. The plate separation is d. Initially, the space between the plates contains only air. Then, an isolated metal sheet of thickness 0.5d is inserted between, but not touching, the plates. How does the potential difference between the plates change as a result of inserting the metal sheet?
a) The potential difference will decrease.
b) The potential difference will not be affected.
c) The potential difference will increase.
d) The potential difference will be zero volts.
19.5.5. The plates of an isolated parallel plate capacitor with a capacitance C carry a charge Q. The plate separation is d. Initially, the space between the plates contains only air. Then, a Teflon ( = 2.1) sheet of thickness 0.5d is inserted between, but not touching, the plates. How does the electric field between the plates change as a result of inserting the Teflon sheet?
a) The electric field will decrease to approximately one-half its initial value.
b) The electric field will not be affected.
c) The electric field will increase to approximately twice its initial value.
d) The electric field will be zero volts per meter.
19.5.6. The plates of an isolated parallel plate capacitor are separated by a distance d and carry charge of magnitude q. The distance between the plates is then reduced to d/2. How is the energy stored in the capacitor affected by this change?
a) The energy increases to twice its initial value.
b) The energy increases to four times its initial value.
c) The energy is not affected by this change.
d) The energy decreases to one fourth of its initial value.
e) The energy decreases to one half of its initial value.
19.5.7. A parallel plate capacitor is connected to a battery that maintains a constant potential difference across the plates. Initially, the space between the plates contains only air. Then, a Teflon ( = 2.1) sheet is inserted between, but not touching, the plates. How does the stored energy of the capacitor change as a result of inserting the Teflon sheet?
a) The energy will decrease.
b) The energy will not be affected.
c) The energy will increase.
d) The energy will be zero joules.