CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
CEDAR CREEK™ SHAKE
INSTALLATION INSTRUCTIONS
NORTH RIDGE™ SLATE
TRUENATURE
METAL ROOFING
Inspired by NatureEngineered by Vicwest
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
TABLE OF CONTENTS PAGE
Important Notice / Safety / Storage / Warranty 1Product Overview 2Trims 3Accessories / Tools – Glossary 4 - 5Roof Preparation 6Fastening 7Installation Procedure Summary 8Shake and Slate Installation Step-by-Step- Layout 9 Installation Details 10 Eave 11 Gable 12 Trim Overlap Details 13 Non-Vented Ridge Cap Detail 14 Vented Ridge Detail 15 Hip Detail without Under Hip Flashing 16 Hip Detail with Under Hip Flashing Hip/Ridge Cap 18 Ridge Cap Detail at Gable End 19 Hip Cap Detail at Eave 20 Under Hip Trim 21 Valley 22 Valley Trim 23 Roof Slope Transition 24 Endwall New Construction 25 Endwall Re-Roof / Existing Cladding Construction 26 Endwall Re-Roof / Existing Masonry Construction 27 Sidewall New Construction 28 Sidewall Re-Roof / Existing Wall Construction 29 Sidewall Re-Roof / Existing Masonry Construction 30 Roof Vent/Pipe Detail 31 Chimney High End Detail 32 Chimney Sidewall Detail 33 Chimney Low End Detail 34 Chimney Trims Installation Steps 35 - 36 Chimney Trims Cutting/Bending 37 Side / End Wall Overlap 38 Reglet Trim 39
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 1 of 39
IMPORTANT NOTICEThe installation guidelines for True Nature Cedar Creek Shake (Shake) and True Nature North Ridge Slate(Slate) metal roof tiles are intended only as a guide for product handling and installation procedures.The materials and methods indicated herein are specified to help maintain overall integrity of the roofingsystem.These guidelines do not address all aspects of the roofing installation or custom roof design requirements.Each specific roof and its construction may require variations from the information in this guideline. Thequality of the installation is ultimately reliant on the experience and workmanship of the roofing contractor.These instructions shall be used as guidelines only and Vicwest assumes no responsibility whatsoeverregarding improper installation or improper use of its products.If you have any questions, please contact your local authorized Vicwest representative. For furtherinformation visit www.vicwest.com.
SAFETYFollow all governmental safety guidelines.The installer/owner of the roof system is responsible to adhere to safe installation practices mademandatory by provincial and/or local ordinances as well as good construction practices.Wearing of appropriate clothing, protective eyewear, light soft-soled shoes, safety gloves, as well asgovernment approved fall arrest equipment are recommended.Maintaining good housekeeping and keeping roof clear of debris as you work is a key ingredient to thesafety of the project.When walking on the roof, use soft-soled, non-marking shoes that will better grip the surface of the tileas well as protect the painted finish. When stepping on the tiles place your foot in the center, not onthe interlocking edges or the tile nosing.
STORAGEShake and Slate tiles and accessories must be stored in a dry, ventilated area protected from moistureand chemicals. It is recommended to install the tile as soon as possible after purchase.
WARRANTYPlease refer to www.vicwest.com for warranty information on the Shake and Slate tile and register yourwarranty when your project is completed.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 2 of 39
WEEP HOLES
EFFECTIVE COVERAGE
EFFE
CTIV
E CO
VER
AG
EEF
FECT
IVE
COV
ERA
GE
4'-2 3/4”
50”
12”
1'-1
9/1
6”
4'-2 11/16”
50”
1'-1
9/16
”
12”
11
1'-15/8”
6 7/16”
TOP-LOCK
TOP-LOCK
FASTENING TRACK
NOSE
EFFECTIVE COVERAGE
EFFECTIVE COVERAGE
SIDE-LOCK
KEYWAY
TOP-LOCK
FASTENING TRACK
NOSE
SIDE-LOCK
KEYWAY WEEP HOLES
PRE-DRILLED HOLES FOR FASTENING
PRE-DRILLED HOLES FOR FASTENING
DIVERTER
FASTENING TRACK
PRE-DRILLED HOLES FOR FASTENING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
SHAKE
SLATE
HIP/RIDGE CAP
15/16”
PRODUCT OVERVIEWInstalled Coverage/Exposure Size: 12” x 50” / tileInstalled Coverage/Exposure Area: 4.17 sqft / tile (24 tiles per square)Installed Weight: 3.76 lbs / tile (90 lbs/square)Tile Depth: 9/16” at the tile noseMaterial: 28ga (0.015”), Grade 33, galvalume coated steel
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 3 of 39
CL
BUILDING PRODUCTS
SHAKE/SLATE ROOF SERIES
FLASHING SKETCHES
EAVE
UNDER HIP
VALLEY
END WALL
Z-FLASHING
REGLET
OUTER GABLE INNER GABLE
Flashings are 10'-0", 28ga (0.015”), Grade 33, Galvalume coated steel
SIDE WALL
SIDE WALL MASONRY END WALL MASONRY
SLOPE CHANGE/TRANSITION
PREPAINTED/EXPOSED SIDE
HIGH END CHIMNEY
TRIMS
The True Nature Trim System is manufactured to suit a majority of installation types but on-site modifications of degrees may be required to suit your specific project needs. Customized trims and flat sheets are also available.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 4 of 39
BUILDING PRODUCTS
SHAKE/SLATE ROOF SERIES
ACCESSORIES
ACCESSORY DESCRIPTIONIMAGE
BLACK, GREY (EPDM)FLEXIBLE PIPE FLASHINGROOF VENT/PIPE SEAL
5/8" x 11 1/2" x 20' ROLL
RIDGE ROOF VENT NYLON 6” PLUS CARBON BLACK FOR
URETHANE / SILICONE SEALANTOR COLOUR MATCHED
1/8"x1/2"x25' LONG
COLOUR MATCHEDEPDM BONDED WASHER
#10 x 1 1/2" LG. PANCAKE HEAD,SELF TAPPING, TYPE 'A'
HIDDEN FASTENER, ZINC PLATED
#10 x 1" LG PANHEAD, PHILIPS DRIVESELF TAPPING, TYPE 'A'
EXPOSED FASTENER, ZINC-PLATED
HIDDEN FASTENER, ZINC PLATED
UV RESISTANCE, NON-WOVEN NYLON-POLYESTER WEATHER BARRIER
FOAM SEALERCLOSED CELL
#8-18 x 3/4" LG. HEX WASHER HEAD, SELF DRILLING, NO. 3 PT, C/W
#10 x 3" LG. HEX HEAD, SELF TAPPING TYPE 'A'
EXPOSED, UV RESISTANT, CLEAR
BUTYL SEALANT NON-EXPOSED, NON-SKINNING,
BUTYL TAPE
COLOUR MATCHED
EXPOSED FASTENER, ZINC-PLATED
NON-DRYING, FLEXIBLE
NON-EXPOSED, NON-SKINNING,NON-DRYING FLEXIBLE
3/4"x1"x20' LONG
#10 x 1 1/2" LG. HEX HEAD,SELF TAPPING, TYPE 'A'
HIDDEN FASTENER, ZINC PLATED
HIDDEN FASTENER, ZINC PLATED #10 x 1 1/2" LG. HEX HEAD,SELF TAPPING, TYPE 'A' C/WEPDM BONDED WASHER
ACCESSORIES
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 5 of 39
BUILDING PRODUCTS
SHAKE/SLATE ROOF SERIES
ACCESSORIES
FITS ALL HAND DRILLS
RECOMMENDED TOOLS: CORDLESS DRILL, CIRCULAR SAW, TIN SNIPS, CHALK LINE, SQUARE, TAPE MEASURE.
ACCESSORY DESCRIPTIONIMAGE
HT SELF-ADHERED UNDERLAYMENT
SYNTHETIC UNDERLAYENT
HIGH PERFORMANCE SELF-ADHESIVE, HIGH TEMPERATURE UNDERLAYMENT FOR METAL ROOFS
HIGH TEMPERATURE WOVEN SYNTHETIC ROOF UNDERLAYMEN.
FOLDING TOOL
TSHD TURBO SHEAR
PORTABLE SHEET METAL BRAKE FOR FORMING FLASHINGS AND TILES
FOR SMALL AREAS
true shear image and description from Steve
TRUE CUT SHEARFOR CUTTING METAL TILES
ACCESSORIES
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 6 of 39
ROOF PREPARATION
Roof SlopeShake and Slate tiles to be used on 3:12 roof slope or greater.Do not install Shake and Slate tiles on roof slopes less than 3:12.Refer to underlayment requirements below for roof slopes at 3:12 and greater than 4:12.
UnderlaymentFollow your local building code and manufacturer’s guidelines for the underlayment requirements, overlapsand installation procedures.• For roof slopes of 3:12 up to under 4:12 install high temperature self-adhered underlayment on entire roof
coverage.• For roof slopes of 4:12 or greater we recommend using high temperature self-adhered underlayment in the
areas that experience most driving rain, snow accumulation or ice damming. In all other areas use synthetic underlayment or #30 felt. See ‘Installation Procedure Summary’ below.
• If required, use underlayment primer on the roof sheathing to ensure proper adherence of the high temperature self-adhered underlayment.
Roof Deck/SheathingIt is recommended to install Shake and Slate tiles on minimum ½” plywood sheathing but no less thanrequired by your local building code.
Roof SquarenessThe installation guidelines assume that the roof is square. Always check the roof squareness first.
New ConstructionPrepare the roof deck to meet local building codes.
Re-Roof ConstructionIt is always recommended to remove the old asphalt shingles before installing the Shake and Slate metal roofing. Inspect existing roof sheathing and underlayment for any deterioration or damage in preparation to meet the local building codes.
Although Vicwest always recommends removing existing asphalt shingles from the roof deck, Shake and Slate may be installed over one layer of asphalt shingles. High quality synthetic underlayment must be applied under the new metal tiles and over the existing asphalt shingles. All foreign materials, damaged or curled tiles must be removed before installation of our metal tiles. Longer fasteners will be required when applying the metal tile on this type of installation. Any imperfection on roof may transmit it through the tile. This is a natural cause and is not a reason for rejection of the product.
When installing new underlayment clear the roof surface from protruding nails, staples or any other debris that could potentially puncture the underlayment. Replacement of existing roof sheathing and underlayment may be required.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 7 of 39
7 x FASTENERS PER TILE
4 x FASTENERS PER TILE
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
FASTENING
• Fasten tile panels with specified fasteners through the pre-punched holes.• Standard fastening requires 4 fasteners per tile #10 x 1 1/2” LG. HEX HEAD, SELF TAPPING, TYPE ‘A’.• In high-wind areas use 7 fasteners per tile in all areas within 3’ of the roof perimeter (around the eaves,
gables and ridge/hips).• Self-tapping screws must penetrate the wood sheathing by minimum 3/8” below the sheathing.• Self-drilling screws must penetrate beyond metal substrate a minimum of 3 pitches of thread.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 8 of 39
SHAKE/SLATE ROOF SERIESBUILDING PRODUCTS ISOMETRIC
SYNTHETIC
HT SELF ADHERED UNDERLAYMENT
TYPICAL ROOF UNDERLAYMENT LAYOUT
INSTALLATION PROCEDURE SUMMARY
1. Check that the existing eave line is straight before starting the eave trim installation. Use a chalk line to mark a straight line across the eave if required. Do not depend on the existing roof edge to be straight or square.
2. Install eave trim.3. Install high temperature self-adhered underlayment along the eave on top of the eave trim.4. Install high temperature self-adhered underlayment in valley, on hips, at slope transitions, end walls, side
walls, around chimneys, skylights and at any roof penetrations, or as required per local building code.5. Install synthetic underlayment on the remaining areas on the entire roof.6. Install inner & outer gable trims.7. Install valley flashing.8. Install end wall & side wall trims.9. Install hip flashing (optional)10. Install Shake/Slate tiles starting at bottom left corner of the roof, proceeding from left to right and from
bottom up. Ensure that keyways and side-locks are staggered.11. Install hip/ridge caps.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 9 of 39
January 8, 2020 [VW Version 2.1] – DRAFT Page 13 of 46
11”
22”
33”
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile Full TileFIFTH COURSE(REPEAT OF ONE)
FOURTH COURSE
THIRD COURSE
SECOND COURSE
FIRST COURSE
ERECTION DIRECTION
FULL SHEET
THIRD CUT
SECOND CUT
FIRST CUT
FULL SHEET
GA
BLE
TRUE NATURE METAL ROOFING Cedar Creek Shake & North Ridge Slate
January 8, 2020 [VW Version 2.1] – DRAFT Page 13 of 46
SHAKE LAYOUT PATTERN
11”
22”
33”
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile Full Tile
SHAKE STAGGERED LAYOUT
Trim the first tile of each course at 11”, 22” and 33” respectively from the edge of the right side lock.
January 8, 2020 [VW Version 2.1] – DRAFT Page 13 of 46
12”
24”
36”
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile
Full Tile Full TileFIFTH COURSE(REPEAT OF ONE)
FOURTH COURSE
THIRD COURSE
SECOND COURSE
FIRST COURSE
ERECTION DIRECTION
FULL SHEET
THIRD CUT
SECOND CUT
FIRST CUT
FULL SHEET
GA
BLE
SLATE STAGGERED LAYOUT
Trim the first tile of each course at 12”, 24” and 36” respectively from the edge of the right side lock.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 10 of 39
SHAKE/SLATE ROOF SERIES
BUILDING PRODUCTS ISOMETRIC
GF
H
D
I
KB
E
C
A
B
JL
ABCDEF
G
IJKL
H
TYPICAL ROOF CONDITION LAYOUT
EAVE - pg 11GABLE - pg 12VENTED OR NON-VENTED RIDGE - pg 14-15UNDER HIP - pg 21VALLEY - pg 22END WALL - pg 25-27
SIDE WALL - pg 28 - 30 SLOPE CHANGE/TRANSITION - pg 24
HIGH END CHIMNEY - pg 32
SIDE WALL MASONRY - pg 30END WALL MASONRY - pg 27
ROOF VENT/PIPE - pg 31
SHAKE AND SLATE INSTALLATION DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 11 of 39
ROOF SHEATHING
FASCIA BOARD
EAVE TRIM
SHAKE/SLATE TILE
HT SELF-ADHERED UNDERLAYMENT OVER EAVE TRIM
1. Eave Trim to be installed on straight line and square to ensure straight edge for the first row of roof tiles. Chalk line the top position of the Eave Trim to accommodate the most prominent outward point of the fascia board, if required.
2. Fasten Eave Trim every 12”.
3. Install HT Self-adhered underlayment strip over Eave Trim, as per local building code.
4. Ensure that the first row of roof tiles is tightly hooked over the Eave Trim and installed at a straight line.
#10 x 1 1/2" LG, PANCAKE-HEAD, TYPE 'A' SCREW@12" O/C
TRUE NATURE COLLECTION
BUILDING PRODUCTS Shake / Slate Series
EAVE DETAIL WITH OVERHANG
EAVE
1. Eave Trim to be installed on straight line and square to ensure straight edge for the first row of roof ties. Chalk line the top position of the eave trim to accommodate the most prominent outward point of the fascia board, if required.
2. Fasten eave trim every 12” using #10 x 1 1/2” LG, PANCAKE-HEAD, TYPE ‘A’ SCREW.
3. Install high temperature self-adhered underlayment strip over eave trim, as per local building code.
4. Ensure that the first row of roof tile is tightly hooked over the eave trim and installed at a straight line.
CUT 1" SLIT FOR EXPANSION
1" MIN
ROOF SLOPE
BOTTOM TRIM
TOP TRIM
OPEN HEM AS REQUIRED FOR OVERLAP
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 12 of 39
31 2"
GABLE BOARD
ROOF SHEATHING
OUTER GABLE
INNER GABLE
SYNTHETIC UNDERLAYMENT
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD,
TYPE 'A' SCREW, C/W EPDM BONDED WASHER
@16" O/C
1. Position Inner Gable Trim flush with the gable board.
2. Install Inner Gable Trim over top of the Eave Trim and fasten in the outer trough at every 16". Do not screw
into the inner trough.
3. Hook Outer Gable over the Inner Gable.
4. Stagger overlap joints of the Inner and Outer Gable Trims.
5. Fasten Outer Gable to the fascia board at every 16”.
INNER GABLE 'BLADE'
INNER TROUGH
OUTER TROUGH
INNER GABLE
#10 x 1" LG, PANHEAD TYPE 'A' SCREWS
@16" O/C
OUTER GABLE 'BLADE'
OUTER GABLE
1" CUT-OUT
AT EAVE PANEL NOSING
SHAKE/SLATE SHINGLE
DIVERTER
DIVERTER
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
GABLE DETAIL GABLE
1. Position inner gable trim flush with the gable board.2. Install inner gable trim over top of the eave trim and fasten in the outer trough at every 16” using #10 x 1 1/2”
LG, HEX-HEAD, TYPE ‘A’ SCREW WITH EPDM BONDED WASHER. Do not screw into the inner trough.3. Hook outer gable over the inner gable.4. Stagger overlap joints of the inner and outer gable trims.5. Fasten outer gable to the fascia board at every 16” using #10 x 1” LG, PANHEAD TYPE ‘A’ SCREWS.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 13 of 39
2" MIN
CUT TRIM AT ANGLE
1"
ROOF SLOPE
BOTTOM TRIM
TOP TRIM
BUILDING PRODUCTS
TRUE NATURE COLLECTIONShake / Slate Series
INNER GABLE TRIM
2" MINOVERLAP
ROOF SLOPE
TRIM OVERLAP DETAILS
INNER GABLE TRIM
BOTTOM TRIM
TOP TRIM
2" MIN
ROOF SLOPE
OPEN HEM AS REQUIRED FOR OVERLAP
BUILDING PRODUCTS
TRUE NATURE COLLECTIONShake / Slate Series
OUTER GABLE TRIM
2 ROWS OFBUTYL CAULKING
2" MINOVERLAP
ROOF SLOPE
OUTER GABLE TRIM
TRUE NATURE COLLECTIONShake / Slate Series
2" MIN
ROOF SLOPE
OPEN HEM AS REQUIRED FOR OVERLAP
STAGGER/OFFSET OVERLAPS OF INNER AND OUTER GABLE TRIMS
BUILDING PRODUCTS
INNER AND OUTER GABLE TRIM LAP DETAIL
INNER AND OUTER GABLE TRIM LAP DETAIL
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 14 of 39
RIDGE/HIP CAP
ROOF SHEATHING
1. Cut the top row of roof shingles at the ridgeline and fasten with 7 equally spaced fasteners to the roof sheathing.
2. Apply con�nuous foam-sealer on top of shingles along the ridge. Ensure that the foam-sealer is posi�oned on the outside edge of the Ridge Cap, in front of the Ridge Cap fasteners.
3. Align Ridge Cap along the ridge. Use chalk line if required.
4. Install Ridge Cap with 3" long screws through the pre-punched slo�ed holes. Do not overdrive fasteners.
2"
5"
RIDGE CAP FASTENER#10 x 3" LG, HEX-HEAD, TYPE 'A'
SYNTHETIC UNDERLAYMENT
FOAM SEALER
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 7 PER SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTIONShake / Slate Series
NON-VENTED RIDGE DETAIL
NON-VENTED RIDGE DETAIL
1. Cut the top row of roof tiles at the ridgeline and fasten with 7 equally spaced #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ WITH EPDM BONDED WASHER fasteners to the roof sheathing.2. Apply continuous foam-sealer on top of tiles along the ridge. Ensure that the foam-sealer is positioned on the
outside edge of the ridge cap, in front of the ridge cap fasteners.3. Align ridge cap along the ridge. Use chalk line if required.4. Install ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ through the pre-punched slotted holes. Do not overdrive fasteners.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 15 of 39
RIDGE/HIP CAP
RIDGE ROOF VENT
ROOF SHEATHING
1. Cut 2” of roof sheathing at the ridge, or as per your local building code.
2. The underlayment should not extend over the cut opening. This is important to maintain un-obstructed ventilation.
3. Cut the top row of roof shingles at the edge of sheathing and fasten with 7 equally spaced fasteners.
4. Apply butyl sealant on the shingle along the ridge and adhere the vented ridge roll to the shingle. Use chalk line if required.
5. Align Ridge Cap along the ridge.
6. Install Ridge Cap with 3" long screws through the pre-punched slotted holes. Do not overdrive fasteners.
2"
5"
RIDGE CAP FASTENER#10 x 3" LG, HEX-HEAD, TYPE 'A'
RAFTERSRIDGE BEAM
1"
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 7 PER SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
VENTED RIDGE DETAIL
VENTED RIDGE DETAIL
1. Cut 2” of roof sheathing at the ridge, or as per your local building code.2. The underlayment should not extend over the cut opening. This is important to maintain unobstructed
ventilation.3. Cut the top row of roof tiles at the edge of sheathing and fasten with 7 equally spaced #10 x 1 1/2” LG, HEX-
HEAD, TYPE ‘A’ WITH EPDM BONDED WASHER fasteners.4. Apply butyl sealant on the tile along the ridge and adhere the vented ridge roll to the tile. Use chalk line if
required.5. Align ridge cap along the ridge.6. Install ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ fasteners through the pre-punched slotted holes. Do not overdrive fasteners.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 16 of 39
1"
RIDG
E CA
P
ROOF
SH
EET
1. Install HT Self-adhered underlayment along the hip, or as required per local building code.
2. Cut, fold and overlap the Shake/Slate shingle over the hip centerline by a minimum 2" onto the opposite side of prevailing winds.
3. Fasten the roof shingle overlap with 2 screws per shingle.
4. Apply continuous foam-sealer on top of the shingles along the hip. Ensure that the foam-sealer is positioned on the outside edge of the Hip Cap, in front of the Hip Cap fasteners.
5. Align Hip Cap along the hip centerline. Use chalk line if required.
6. Install Hip Cap with 3" long screws through the pre-punched slotted holes. Do not overdrive fasteners.
HT SELF-ADHERED UNDERLAYMENT
FOLD SHINGLE OVER THE HIP LINE BY MIN 2"
FOAM SEALER
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 2 PER SHINGLE
2"HIP CAP FASTENER#10 x 3" LG, HEX-HEAD,TYPE 'A'
2"
OVERLAP
RIDGE/HIP CAP
SHAKE/SLATE SHINGLE
PREVAILING WINDS
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
HIP DETAIL WITHOUT HIP UNDER-FLASHING (OPTIONAL)
HIP DETAIL WITHOUT UNDER HIP FLASHING
1. Install high temperature self-adhered underlayment along the hip, or as required per local building code.2. Cut, fold and overlap the Shake/Slate tile over the hip centerline by a minimum 2” onto the opposite side of
prevailing winds.3. Fasten the roof tile overlap with 2 #10 x 1 1/2” LG, HEX-HEAD,TYPE ‘A’ SCREW WITH EPDM BONDED
WASHER, per tile.4. Apply continuous foam-sealer on top of the tiles along the hip. Ensure that the foam-sealer is positioned on
the outside edge of the hip cap, in front of the hip cap fasteners.5. Align hip cap along the hip centerline. Use chalk line if required.6. Install hip cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ screws through the pre-punched slotted holes. Do not overdrive fasteners.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 17 of 39
RIDGE/HIP CAP
ROOF SHEATHING
1. Install HT Self-adhered underlayment along the hip.
2. Align Hip Flashing on the hip and install over top of Eave Trim.
3. Cut the end of Hip Flashing on angles to match the two adjoining eave sec�ons.
4. Fasten Hip Flashing in the outer trough at every 16". Do not screw into the inner trough.
5. Cut the Shake/Slate shingles along the hip centerline and fasten to the roof sheathing, outside of Hip Under-Flashing
6. Apply con�nuous foam-sealer on top of the shingles along the hip. Ensure that the foam-sealer is posi�oned on the outside edge of the Hip Cap, in front of the Hip Cap fasteners.
7. Align Hip Cap along the hip centerline. Use chalk line if required.
8. Install Hip Cap with 3" long screws through the pre-punched slo�ed holes. Do not overdrive fasteners.
2"
HT SELF-ADHEREDUNDERLAYMENT
HIP UNDER FLASHING
DIVERTER
HIP FLASHING
OUTER TROUGH
INNER TROUGH
FOAM SEALER
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 16" O/C
HIP CAP FASTENER#10 x 3" LG, HEX-HEAD,TYPE 'A'
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 7 PER SHINGLE
DIVERTER
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTIONShake / Slate Series
HIP DETAIL WITH HIP UNDER FLASHING HIP DETAIL WITH UNDER HIP FLASHING (OPTIONAL)
1. Install high temperature self-adhered underlayment along the hip.2. Align hip flashing on the hip and install over top of eave trim.3. Cut the end of hip flashing on angles to match the two adjoining eave sections.4. Fasten hip flashing in the outer trough at every 16” using #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ SCREW WITH
EPDM BONDED WASHER. Do not screw into the inner trough.5. Cut the Shake/Slate tiles along the hip centerline and fasten to the roof sheathing TYPE ‘A’ SCREW WITH
EPDM BONDED WASHER outside of hip under-flashing6. Apply contiuous foam-sealer on top of the tiles along the hip. Ensure that the foam-sealer is positioned on
the outside edge of the hip cap, in front of the hip cap fasteners.7. Align hip cap along the hip centerline. Use chalk line if required.8. Install hip cap with#10 x 3” LG, HEX-HEAD, TYPE ‘A’ fasteners through the pre-punched slotted holes. Do not
overdrive fasteners.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 18 of 39
7"
11.85"
1. Align Shake/Slate Ridge/Hip Cap along the ridge or hip. Use chalk line if required.
2. Install Ridge/Hip Cap with 3" long wood screws through the center of the pre-punched slotted holes. Do not overdrive fasteners.
3. Ensure Ridge/Hip caps are tightly hooked into the lock and installed in straight line.
4. Note: On roof pitches greater than 12:12 Ridge Hip Cap requires snip at nosing and fastening track to allow for overbending of cap.
2"
S-LOCK
PRE-DRILLED HOLES FOR FASTENING
RIDGE/HIP CAP FASTENERS#10 x 3" LG, HEX-HEAD, TYPE 'A'
SNIP CAP NOSING TO ALLOW BENDING
SNIP FASTENING TRACK AND DIVERTER TO ALLOW BENDING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
RIDGE/HIP CAP
12:12 Ridge Diagram
HIP/RIDGE CAP
1. Align Shake/Slate Hip/Ridge Cap along the ridge or hip. Use chalk line if required.2. Install hip/ridge cap with #10 x 3” LG, HEX-HEAD, TYPE ‘A’ FASTENERS through the center of the pre-
punched slotted holes. Do not overdrive fasteners.3. Ensure hip/ridge caps are tightly hooked into the top lock and installed in straight line.4. Note: On roof pitches greater than 12:12 hip/ridge cap requires snip a v-cut at nosing and fastening track to
allow for overbending of the cap (refer to diagram).
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 19 of 39
1. Snip Ridge/Hip Cap edges as shown and fold-in.
2. Snip the middle of the ridge cap approximately 1" along the center.
3. You may need to snip the line on a small angle depending on roof pitch so the trim can fold over.
4. Fold front tab into hem and bend at gable edge to 90 degrees.
a. The cap should sit outside the gable trim
b. Fasten the turned down cap edges to the gable trim with #10 x 1" LG Panhead, type 'A' screws
RIDGE CAP FOLDED OVER GABLE
#10 x 1" LG., PANHEAD TYPE 'A' SCREWS(COLOUR TO MATCH)
SNIP CAP BACK1" MIN, IN A V-CUT
FOLD LINE
FOLD IN FOR HEM3" M
IN
CUT LINE
FOLD IN
CUT LINE
ROOF LINE/GABLE EDGE
ROOF LINE/GABLE EDGE
3" MIN
MIN 1"
CUT OUTER EDGE TOFIT OVER GABLE TRIM
RIDGE/HIP CAP
SHAKE/SLATESHINGLE
1"
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
RIDGE CAP DETAIL AT GABLE END
RIDGE CAP DETAIL AT GABLE END
1. Snip ridge cap edges as shown and fold in.2. Snip the middle of the ridge cap approximately 1” along the center.3. You may need to snip the line on a small angle depending on roof pitch so the trim can fold over.4. Fold front tab into hem and bend at gable edge to 90 degrees. a) The cap should sit outside the gable trim b) Fasten the turned down cap edges to the gable trim with colour matched #10 x 1” LG panhead,
type ‘A’ screws
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 20 of 39
HIP CAP DETAIL AT EAVE
1. Mark the underside of the hip cap along the angle of the eave edge. This is your marked cut line.2. From the marked cut line, measure 2 more fold lines at 5/8” and 1/2” apart. 3. Note: You may be required to increase the spacing between the fold lines when using the under hip flashing
option. 4. Cut at the 1st fold line on the outer edge of hip cap.5. Snip a v-cut in the middle of the hip cap along the centre crease. a) Fold front tab into hem and bend at eave edge to match eave b) Fasten the turned down cap edges to the tile nose with #10 x 1” LG, panhead, type ‘A’ screws.6. Install the remainder of hip/ridge caps in a straight line.
1. Mark the angle of the eave on the underside of the Ridge/Hip Cap.
2. From the scribed line, mark 2 more fold lines at 58" and 1
2" apart. Note: 1" may be required for large metal build-up when using Hip Under Flashing option.
3. Cut at the 1st fold line on the outer edge of hip cap.
4. Snip a “V” in the middle of the Ridge/Hip Cap along the centre crease.
a. Fold front tab into hem and bend at eave edge to match eave
b. Fasten the turned down cap edges to the shingle nose with #10 x 1" LG, Panhead, type 'A' screws.
5. Install the remainder of Ridge/Hip Caps in a straight line.
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
HIP CAP DETAIL AT EAVE
EAVE EDGE
FOLD LINES
MARKED CUT LINE
OFFCUT
FORMED NOSE OFHIP CAP AT EAVE
5/8”1/2”
1/2”
5/8”
V-CUT AT CENTER
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 21 of 39
TOP TRIM
BOTTOM TRIM
2" MIN
ROOF SLOPE
FOLD OUT EDGES TO ALLOW TOP TRIM TO NEST INSIDE BOTTOM TRIM
2 ROWS OF BUTYL CAULKING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate SeriesHIP TRIM
UNDER HIP TRIM
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 22 of 39
1. Install HT self-adhered underlayment in the valley.
2. Align Valley flashing on the valley and position over Eave trim.
3. Cut the end of Valley flashing on angles matching the two adjoining eave sections and installed cut edge at 1" up from eave edge.
4. Push the Valley flashing tight into the roof and fasten in the outer trough at every 24".
5. Cut the metal shingle to fit the valley angle.
6. Refer to tile notching/folding instructions.
INNER TROUGH
OUTER TROUGHDIVERTER
CL
1-PIECE VALLEY FLASHING
ROOF SHEATHING
HT SELF-ADHERED UNDERLAYMENT
VALLEY FLASHING FASTENER #10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER @ 24" O/C
3"CUT-OUT AT EAVE PANEL NOSING
SHINGLE FASTENER #10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW
SHAKE/SLATE SHINGLE
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
VALLEY
TRUE NATURE COLLECTION
Shake / Slate Series
36" HT SELF-ADHERED UNDERLAYMENT EXTEND 18" UP & DOWN FROM TRANSITION POINT
VALLEY
1. Install high temperature self-adhered underlayment in the valley.2. Align valley flashing on the valley and position over eave trim.3. Cut the end of valley flashing on angles matching the two adjoining eave sections and installed cut edge at 1”
up from eave edge.4. Push the valley flashing tight into the roof and fasten in the outer trough at every 24” using #10 x 1 1/2” LG,
HEX-HEAD, TYPE ‘A’ SCREW, EPDM BONDED WASHER.5. Cut the metal tile to fit the valley angle.6. Refer to tile notching/folding instructions.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 23 of 39
CONT. BUTYL CAULKING ACROSS LAP
CUT FLASHING ON ANGLE 6" BACK
6" MIN
TOP TRIM
BOTTOM TRIM
ROOF SLOPE
6" OVERLAP
6" MIN
SNIP AND FOLD WATER DIVERTER BACK FOR OVERLAP
CONT. BUTYL CAULKING
INSERT BUTYL CAULKING INTO CUT WING
CONT. BUTYL CAULKING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series VALLEY TRIM
VALLEY TRIM
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 24 of 39
UPPER SHAKE/ SLATE SHINGLE
ROOF TRANSITION TRIM
LOWER SHAKE/SLATE SHINGLE
HT SELF-ADHERED UNDERLAYMENT
ROOF SHEATHING
36" HT SELF-ADHERED UNDERLAYMENT EXTEND 18" UP & DOWN FROM TRANSITION POINT
1. Apply HT Self-adhered underlayment, along transi�on roof line.
2. Measure and cut shingle 2" above the roof pitch change. Bend shingle to suit slope change.
3. Fasten lower roof shingle with 7 equally spaced fasteners to the roof sheathing.
4. Apply foam-sealer 2" below roof pitch change on the lower roof shingles.
5. Fasten Roof Transi�on Trim to the lower roof shingle through foam sealer at every 16".
6. Set Starter Trim on butyl tape on the upper roof slope, on top of Roof Transi�on Trim and fasten every 12".
7. Install first course of Shake/Slate shingle on the upper roof slope.
#8-18 x 3/4" LG. MAX., HWH NO. 2 PT. W/ NEOPRENE WASHER AT 16" O/C
FOAM SEALER
2"
BUTYL TAPE
STARTER TRIM
#10 x 1 1/2” LG. HEX-HEAD TYPE 'A' SCREW, C/WEPDM BONDED WASHER@ 12" O/C
2"
BUILDING PRODUCTS
ROOF SLOPE TRANSITION
TRUE NATURE COLLECTIONShake / Slate Series
#10 x 1 1/2" LG, PANCAKE-HEAD,TYPE 'A' SCREW @12" O/C
FROM THE PITCH CHANGE ADD LAYER OF SYNTHETIC UNDERLAYMENT BELOW THE HT S/A
FROM THE PITCH CHANGE ADD LAYER OF SYNTHETIC UNDERLAYMENT BELOW THE HT S/A
ROOF SLOPE TRANSITION
1. Apply high temperature self-adhered underlayment, along transition roof line.a) It is important to put the high temperature self-adhered underlayment on top of the
syntheticunderlayment on the lower roof slope.b) It is important to put the high temperature self-adhered underlayment under the synthetic
underlayment on the upper roof slope.2. Measure and cut tile 2” above the roof pitch change. Bend tile to suit slope change.3. Fasten lower roof tile with 7 X #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’ SCREW with EPDM BONDED WASHER
equally spaced fasteners to the roof sheathing.4. Apply foam-sealer 2” below roof pitch change on the lower roof tiles.5. Fasten roof transition trim to the lower roof tile through foam sealer at every 16” using #8-18 x 3/4” LG. MAX.,
HWH NO. 2 PT. W/ NEOPRENE WASHER6. Set starter trim on butyl tape on the upper roof slope, on top of roof transition trim and fasten every 12” using
#10 x 1 1/2” LG, PANCAKE-HEAD, TYPE ‘A’ SCREW7. Install first course of Shake/Slate tile on the upper roof slope.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 25 of 39
END WALL TRIM
EXTERIOR CLADDING
CARRY 6” HT SELF-ADHERED UNDERLAYMENT UP WALL ASSEMBLY
1. Apply HT Self-adhered underlayment at least 6” up the endwall.
2. Measure and cut shingle with a min 12" fold up at the base of the wall.
3. Set Z-flashing in butyl sealant on top of shingle and fasten into plywood with 7 equally spaced fasteners per shingle .
4. Hook Endwall Transition Trim over Z-flashing and fasten at every 16” to the end-wall substrate.
5. Apply continuous sealant at base of Z-flashing.
6. Apply underlayment strip over the transition trim behind new wall cladding.
#10 x 1 1/2” LG. MAX., HEXHEAD TYPE 'A' SCREW, C/W EPDM BONDED WASHER
UNDERLAYMENT STRIP OVER END WALL
1/2” MIN FOLD-UPON LAST COURSE OF SHINGLES
CONTINUOUS BUTYL SEALANT
CONTINUOUS URETHANE/SILICONE SEALANT
Z-FLASHING
#10 x 1 1/2” LG. PANCAKE HEAD (TYP.)@ 16" O/C
#10 x 1 1/2” LG. MAX., HEXHEAD TYPE 'A' SCREW
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
ENDWALL
TRUE NATURE COLLECTION
Shake / Slate Series
NEW CONSTRUCTION ENDWALLNEW CONSTRUCTION
1. Carry high temperature self-adhered underlayment at least 6” up the endwall.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last couple of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG.
MAX., HEX HEAD TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER per tile.4. Hook end wall trim over Z-flashing and fasten with #10 x 1 1/2” LG. PANCAKE HEAD every 16” to the end-wall substrate.5. Apply continuous urethane/silicone sealant at base of Z-flashing.6. Apply underlayment strip over the transition trim behind new exterior cladding.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 26 of 39
1/2” MIN FOLD-UP
CONT. BUTYL CAULKING
REGLET TRIM
ENDWALL TRANSITION TRIM
EXISTING CLADDING
HT SELF-ADHERED UNDERLAYMENT
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER
CONTINUOUS SEALANT UNDERLAYMENT STRIP OVER ENDWALL TRANSITION TRIM
1. Ensure that HT Self-adhered underlayment is installed at wall to roof transition as required.
2. Measure and cut shingle with a min 12" fold up at the base of the wall .
3. Set Z-flashing in butyl sealant on top of shingle and fasten into plywood with 7 equally spaced fasteners per shingle .
4. Hook Endwall Transition Trim over Z-flashing and fasten every 16” to the face of existing wall cladding.
5. Apply continuous sealant at base of Z-flashing .
6. Apply underlayment strip over the Endwall Transition Trim and onto the face of existing wall.
7. Install Reglet Trim over the underlayment strip and fasten every 12".
8. Apply continuous sealant along the top edge of the Reglet Trim.
Z-FLASHING
CONT. SEALANT
#10 x 1" LG PANHEAD TYPE 'A' SCREW @ 12" O/C
#10 x 1 1/2” LG. PANCAKE HEAD @ 16" O/C
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
ENDWALL
TRUE NATURE COLLECTION
Shake / Slate Series
RE-ROOF / EXISTING WALL CONSTRUCTION
ENDWALLRE-ROOF / EXISTING CLADDING CONSTRUCTION
1. Carry high temperature self-adhered underlayment at least 6” up the endwall.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last course of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG.
MAX., HEX HEAD TYPE ‘A’ SCREW, WITH BONDED WASHER per tile.4. Hook end wall trim over Z-flashing and fasten with #10 x 1 1/2” LG. PANCAKE HEAD every 16” to the face of exiting cladding.5. Apply continuous urethane/silicone sealant at base of Z-flashing.6. Apply 2” strip of high temperature underlayment over the end wall trim and onto the face of existing
cladding.7. Install reglet trim over the underlayment strip and fasten every 12” using #10 x 1” LG PANHEAD TYPE ‘A’
SCREW8. Apply continuous sealant along the top edge of the reglet trim.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILSPLEASE REFERENCE PAGE 39 FOR REGLET TRIM DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 27 of 39
END WALL MASONRY TRIM
HT SELF-ADHERED UNDERLAYMENT
CONT. SEALANT IN GROOVE
1/2” MIN FOLD-UP
1. Ensure that HT Self-adhered underlayment is installed at wall to roof transition as required.
2. Measure and cut shingle with a min 12" fold up at the base of the wall .
3. Set Z-flashing in butyl sealant on top of shingle and fasten into plywood with 7 equally spaced fasteners per shingle .
4. Cut groove in masonry for Endwall Reglet Trim installation.
5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.
6. Hook Endwall Reglet Trim over Z-flashing and embed into sealant in the masonry groove.
7. Fasten Endwall Reglet Trim to Z-flashing with pop-rivets every 24".
8. Apply continuous sealant at base of Z-flashing.
CONTINUOUSBUTYL SEALANT
Z-FLASHING
CONTINUOUS SEALANT
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER
POP-RIVETS AT 24" O/C
BUTYL TAPE
ROOF SHEATHING
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW
BUILDING PRODUCTS
ENDWALL
TRUE NATURE COLLECTION
Shake / Slate Series
RE-ROOF / EXISTING MASONRY CONSTRUCTION
EXISTING MASONRY CONSTRUCTION
ENDWALLRE-ROOF / EXISTING MASONRY CONSTRUCTION
1. Carry high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Measure and cut tile with a min 1/2” fold up at the base of the wall for last couple of tiles.3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG,
HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER per tile.4. Cut groove in masonry for end wall masonry installation.5. Apply continue urethane/silicone sealant along groove in masonry, and apply butyl tape on top of Z-flashing.6. Hook end wall masonry over Z-flashing and embed into sealant in the masonry groove.7. Fasten end wall masonry to Z-flashing with pop-rivets every 24”.8. Apply continuous sealant at base of Z-flashing.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 28 of 39
CARRY UNDERLAYMENT 6” UP WALL SUBSTRATE
SIDE WALL TRIM
INNER GABLE TRIM
EXTERIOR CLADDING
1. Apply HT Self-adhered underlayment at least 6” up the sidewall.
2. Install Inner Gable Trim along the sidewall and attach in the outer trough at every 12”.
3. Hook Sidewall Transition Trim tight onto Inner Gable and fasten at every 12” to the sidewall substrate.
4. Apply underlayment strip over the Sidewall Transition Trim behind new wall cladding.
5. Slide shingles into the Inner Gable Trim .
CARRY MEMBRANE OVER SIDE WALL
#10 x 1 1/2” LG. PANCAKE HEAD, TYPE'A' SCREW @ 16" O/C
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 12" O/C
2 1/2”SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
SIDEWALL
TRUE NATURE COLLECTION
Shake / Slate Series
NEW CONSTRUCTION SIDEWALLNEW CONSTRUCTION
1. Apply high temperature self-adhered underlayment at least 6” up the sidewall.2. Install inner gable trim along the sidewall and attach in the outer trough at every 16” using #10 x 1 1/2” LG.
PANCAKE HEAD, TYPE ‘A’ SCREW3. Hook side wall trim tight onto inner gable and fasten at every 12” using #10 x 1 1/2” LG, HEX-HEAD, TYPE ‘A’
SCREW to the sidewall substrate.4. Apply underlayment strip over the side wall trim behind new wall cladding.5. Slide tiles into the inner gable trim.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 29 of 39
HT SELF-ADHERED UNDERLAYMENT
SIDE WALL TRIM
INNER GABLE TRIM
CONTINUOUS SEALANT
EXISTING CONSTRUCTION
UNDERLAYMENT STRIP OVER SIDE WALL TRIM
1. Ensure that HT Self-adhered underlayment is installed at wall to roof transition as required.
2. Install Inner Gable trim along the existing sidewall and attach in the outer trough at every 12".
3. Hook Sidewall Transition Trim tight onto Inner Gable and fasten at every 12" to the sidewall.
4. Apply underlayment strip over Sidewall Transition Trim and onto the face of existing sidewall.
5. Install Reglet Trim over the underlayment strip and fasten every 16".
6. Apply continuous sealant along the top edge of the Reglet Trim.
7. Slide shingles into the Inner Gable Trim .
REGLET TRIM
2 1/2”
#10 x 1" LG PANHEAD TYPE 'A' SCREW @ 12" O/C
#10 x 1 1/2” LG. PANCAKE HEAD @ 16" O/C
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 12" O/C
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
SIDEWALL
RE-ROOF / EXISTING WALL CONSTRUCTION
SIDEWALLRE-ROOF / EXISTING WALL CONSTRUCTION
1. Ensure that high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Install inner gable trim along the existing sidewall and attach in the outer trough at every 12” with #10 x 1 1/2”
LG, HEX-HEAD, TYPE ‘A’ SCREW, C/W WITH BONDED WASHER.3. Hook side wall trim tight onto inner gable and fasten to the sidewall every 16” using #10 x 1 1/2” LG.
PANCAKE HEAD.4. Apply underlayment strip over side wall trim and onto the face of existing sidewall.5. Install reglet trim over the underlayment strip and fasten every 12” using #10 x 1” LG PANHEAD TYPE ‘A’
SCREW.6. Apply continuous Urethane/silicone sealant along the top edge of the reglet trim.7. Slide tiles into the inner gable trim.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS PLEASE REFERENCE PAGE 39 FOR REGLET TRIM DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 30 of 39
SIDE WALL MASONRY
INNER GABLE TRIM
EXISTING MASONRY CONSTRUCTION
CONTINUOUS SEALANT IN GROOVE
1. Ensure that HT Self-adhered underlayment is installed at wall to roof transition as required.
2. Install Inner Gable trim along the existing sidewall and attach in the outer trough every 12"
3. Cut groove in masonry for Sidewall Reglet Trim installation.
4. Apply continuous sealant along groove in masonry and apply butyl tape on top of Inner Gable Trim.
5. Hook Sidewall Reglet Trim over Inner Gable and embed into sealant in the masonry groove.
6. Fasten Sidewall Reglet Trim to Inner Gable with pop-rivets at every 24".
7. Slide shingles into the Inner Gable Trim .
2 1/2”
POP-RIVETS AT 24" O/C
HT SELF-ADHERED UNDERLAYMENT
BUTYL TAPE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 12" O/C
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
SIDEWALL
RE-ROOF / EXISTING MASONRY CONSTRUCTION
SIDEWALLRE-ROOF / EXISTING MASONRY CONSTRUCTION
1. Ensure that high temperature self-adhered underlayment is installed at wall to roof transition as required.2. Install inner gable trim along the existing sidewall and attach in the outer trough every 12” #10 x 1 1/2” LG,
HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for side wall masonry trim installation.4. Apply continuous sealant along groove in masonry and apply butyl tape on top of inner gable trim.5. Hook side wall masonry trim over inner gable and embed into sealant in the masonry groove.6. Fasten side wall masonry trim to inner gable with pop-rivets at every 24”.7. Slide tiles into the inner gable trim.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 31 of 39
ROOF VENT/PIPESILICONE SEALANT BETWEEN FLEXIBLE PIPE FLASHING AND ROOF VENT/PIPE
#8 x 18 x 3/4" LG. HEX WASHER HEAD, SELF DRILLING, NO. 3 PT, C/W NEOPRENE WASHERS
NEW OR EXISTING SHEATHING
SILICONE SEALANT BETWEEN FLEXIBLE PIPE FLASHING AND METAL ROOF, UNDER PERIMETER FLANGE
FLEXIBLE PIPE FLASHING
1. Measure size of pipe/stack and cut required diameter of boot to suit.
2. Install self-adhered underlayment around the perimeter of the base of the pipe/stack.
3. Apply a generous amount of sealant from the topside of the pipe/stack forming the shape of a “U”.
4. Install the Flexible Pipe Flashing following the manufactures installation guideline.
Potential use of a snow break may be required over the pipe or stack. Please consult your local representative for more information.
HT SELF-ADHERED UNDERLAYMENT
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
ROOF VENT/PIPE DETAIL
ROOF VENT/PIPE DETAIL
1. Measure size of pipe/stack and cut required diameter of boot to suit.2. Install self-adhered underlayment around the perimeter of the base of the pipe/stack.3. Apply a generous amount of sealant from the topside of the pipe/stack forming the shape of a “U”.4. Install the flexible pipe flashing following the manufactures installation guideline.
Potential use of a snow break may be required over the pipe or stack. Please consult your local representative formore information.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 32 of 39
1. Ensure that HT self-adhered underlayment is installed up the masonry wall.
2. Install Inner Gable Trim against the masonry wall and attach in the outer trough at every 24”.
3. Cut groove in masonry for High End Reglet Trim installation.
4. Install shingles into the Inner Gable.
5. Apply continuous sealant along masonry groove.
6. Install High End Reglet into lap of second shingle course and embed into sealant in the masonry. Fasten to masonry at 12" O/C.
7. Apply continuous sealant at the High End Reglet Trim at the shingle lap.
8. Refer to 'Chimney Trims Installation Steps' for sealant locations at Reglet trims intersections at chimney corners.
ROOF SHEATHING
MASONRY
HIGH END CHIMNEY
INNER GABLE TRIM
FIELD SNIP AND FOLD PANEL END
HT SELF-ADHERED UNDERLAYMENT
FLASHING TO TERMINATE UNDER LAP OF 2ND PANEL FROM CHIMNEY
CONTINUOUS SEALANT IN GROOVE
CONTINUOUS SEALANT
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 24" O/C
SHAKE/SLATE SHINGLE
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
CHIMNEY HIGH END DETAIL
CHIMNEY HIGH END DETAIL
1. Ensure that high temperature self-adhered underlayment is installed up the masonry wall.2. Install inner gable trim against the masonry wall and attach in the outer trough at every 24” using #10 x 1 1/2”
LG, HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for high end chimney trim installation.4. Install tiles into the inner gable.5. Apply continuous sealant along masonry groove.6. Install high end chimney trim into lap of second tile course and embed into sealant in the masonry. Fasten to
masonry with standard masonry screws every 12” O/C.7. Apply continuous sealant at the high end chimney trim at the tile lap.8. Refer to ‘Chimney Trims Installation Steps’ for sealant locations at masonry trims intersections at chimney
corners.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 33 of 39
1. Ensure that HT Self-adhered underlayment is installed at the roof to chimney transition as required.
2. Install Inner Gable trim along the chimney sidewall and attach in the outer trough every 16"
3. Cut groove in masonry for Sidewall Reglet Trim installation.
4. Apply continuous sealant along groove in masonry and butyl tape on top of Inner Gable Trim.
5. Hook Sidewall Reglet Trim over Inner Gable and embed into sealant in the masonry groove.
6. Fasten Endwall Reglet Trim to Inner Gable with pop-rivets at every 24".
7. Slide shingles into the Inner Gable Trim .
SIDE WALL MASONRY
INNER GABLE TRIM
EXISTING MASONRY CONSTRUCTION
CONTINUOUS SEALANT IN GROOVE
2 1/2”
POP-RIVETS AT 24" O/C
HT SELF-ADHERED UNDERLAYMENT
BUTYL TAPE#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER@ 16" O/C
SHAKE/SLATE SHINGLE
ROOF SHEATHING
BUILDING PRODUCTS Shake / Slate Series
CHIMNEY SIDEWALL DETAIL
TRUE NATURE COLLECTION
CHIMNEY SIDEWALL DETAIL
1. Ensure that HT Self-adhered underlayment is installed at the roof to chimney transition as required.2. Install inner gable trim along the chimney sidewall and attach in the outer trough every 16” using #10 x 1 1/2”
LG,HEX-HEAD, TYPE ‘A’ SCREW, C/W EPDM BONDED WASHER3. Cut groove in masonry for side wall masonry trim installation.4. Apply continuous sealant along groove in masonry and butyl tape on top of inner gable trim.5. Hook side wall masonry trim over inner gable and embed into sealant in the masonry groove.6. Fasten side wall masonry trim to inner gable with pop-rivets at every 24”.7. Slide tiles into the inner gable trim.
PLEASE REFERENCE PAGE 38 FOR SIDE / END WALL OVERLAP DETAILS
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 34 of 39
END WALL MASONRY
EXISTING CONSTRUCTION (MASONRY)
HT SELF-ADHERED UNDERLAYMENT
CONT. SEALANT IN GROOVE
1/2” MIN FOLD-UP
CONTINUOUSBUTYL SEALANT
Z-FLASHING
CONTINUOUS SEALANT
POP-RIVETS AT 24" O/C
BUTYL TAPE
ROOF SHEATHING
1. Ensure that HT Self-adhered underlayment is installed at roof to chimney transition as required.
2. Measure and cut shingle with a min 12" fold up at the base of the wall .
3. Set Z-flashing in butyl sealant on top of shingle and fasten into plywood with 7 equally spaced fasteners per shingle .
4. Cut groove in masonry for Endwall Reglet Trim installation.
5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.
6. Hook Endwall Reglet Trim over Z-flashing and embed into sealant in the masonry groove.
7. Fasten Endwall Reglet Trim to Z-flashing with pop-rivets every 24".
8. Apply continuous sealant at base of Z-flashing.
SHAKE/SLATE SHINGLE
#10 x 1 1/2" LG, HEX-HEAD, TYPE 'A' SCREW, C/W EPDM BONDED WASHER
BUILDING PRODUCTS Shake / Slate Series
CHIMNEY LOW END DETAIL
TRUE NATURE COLLECTION
CHIMNEY LOW END DETAIL
1. Ensure that high temperature self-adhered underlayment is installed at roof to chimney transition as required.
2. Measure and cut tile with a min 1/2” fold up at the base of the wall .3. Set Z-flashing in butyl sealant on top of tile and fasten into plywood with 7 equally spaced #10 x 1 1/2” LG,
HEX-HEAD, TYPE ‘A’ SCREW, WITH EPDM BONDED WASHER fasteners per tile.4. Cut groove in masonry for end wall masonry trim installation.5. Apply continuous sealant along groove in masonry, and apply butyl tape on top of Z-flashing.6. Hook end wall masonry trim over Z-flashing and embed into sealant in the masonry groove.7. Fasten end wall masonry trim to Z-flashing with pop-rivets every 24”.8. Apply continuous sealant at base of Z-flashing.
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 35 of 39
TYPICAL ROOF CHIMNEY
SHAKE OR SLATE ROOF SHINGLE
TYPICAL ROOF CHIMNEY
ROOF SHEATHING WITH HT SELF-ADHERED UNDERLAYMENT
INNER GABLE CONTINUOUS AROUND OPENING (EXCEPT BOTTOM)
INNER GABLE CONTINUOUS AROUND OPENING (EXCEPT BOTTOM)
INNER GABLE RUNSOVER TOP OF SIDE INNER GABLE
2" +/-
INNER GABLE TO PROTRUDE THROUGH BOTTOM SHEET
1" x 1/2” GROOVE FOR TRIM DUCKBILL
INSTALL Z-FLASHING ONTO SHAKE/SLATE TILE
TRIM CORNER OF INNER GABLE AS REQUIRED
FLATTEN DIVERTERS AS REQUIRED PRIOR TO APPLYING 2 ROWS OF BUTYL CAULKING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
STEP 1
STEP 2
1" x 1/2” GROOVE FOR TRIM DUCKBILL
CHIMNEY TRIMS INSTALLATION
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 36 of 39
TYPICAL MASONRY CHIMNEY
SHAKE OR SLATE ROOF SHINGLEBENEATH FLASHINGS CONTINUOS BUTYL SEALANT
APPLIED TO TRIM SURFACE
BUTYL SEALANT BOTH SIDES OF FLAP (TYP.)
GENEROUS AMOUNT OF BUTYL SEALANT
BUTYL SEALANT BOTH SIDES OF FLAP (TYP.)
TYPICAL MASONRY CHIMNEY
SHAKE OR SLATE ROOF SHINGLEBENEATH FLASHINGS
FLASHING FLAPS FOLDED TOGETHER
CONTINUOS BUTYL SEALANT APPLIED IN MASONRY GROOVE AROUND ENTIRE CHIMNEY
END WALL MASONRY
SIDE WALL MASONRY
HIGH END CHIMNEY
SIDE WALL MASONRYEND WALL MASONRY
HIGH END CHIMNEY
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
STEP 3
STEP 4
CHIMNEY TRIMS INSTALLATION
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 37 of 39
1
2
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate SeriesCHIMNEY TRIMS AT HIGH END
1
2
3
CHIMNEY TRIMS AT SIDEWALL
FOLD
CUT
FOLD
CUT
FOLDFOLD
CUT
CHIMNEY TRIMS CUTTING/BENDING
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
CHIMNEY BOTTOM
1
2
CUT
FOLD
1
2
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate SeriesCHIMNEY TRIMS AT HIGH END
1
2
3
CHIMNEY TRIMS AT SIDEWALL
FOLD
CUT
FOLD
CUT
FOLDFOLD
CUT
CHIMNEY TRIMS ON HIGH END
CHIMNEY TRIMS AT SIDE WALL CHIMNEY TRIMS AT BOTTOM
1
2
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate SeriesCHIMNEY TRIMS AT HIGH END
1
2
3
CHIMNEY TRIMS AT SIDEWALL
FOLD
CUT
FOLD
CUT
FOLDFOLD
CUT
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 38 of 39
ROOF SLOPE
TOP TRIM
BOTTOM TRIM
4" MIN
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate SeriesENDWALL/SIDE WALL TRIM
ROOF SLOPE
4" MIN
SIDE WALL TRIM
END WALL TRIM
SIDE / END WALL OVERLAP
TRUE NATURE METAL ROOFING
CEDAR CREEK™ SHAKE and NORTH RIDGE™ SLATE
Page 39 of 39
TOP TRIM
BOTTOM TRIM
BUTYL CAULKING/TAPE CONTINUOUS ACROSS LAP
ROOF SLOPE
2" MIN
OPEN HEM AS REQUIRED FOR OVERLAP
BUILDING PRODUCTS
TRUE NATURE COLLECTION
Shake / Slate Series
REGLET TRIM
REGLET TRIM
As of June 2020 V1