Download - Catalogue of Plates New[1]

PLATES

PRODUCT CATALOGUE

2

THE 3.5 M FOUR-HIGH ROLLING MILL

The rolling mill was founded in 1971 and underwent a large modernization in 1999 which facilitated a considerable improvement of the rolled material geometry, surface quality and expansion of the product mix. Plates are made from concast slabs. Plates are rolled in the thickness range from 5 to 80 mm, and in the width range from 1,000 to 3,300 mm.

THE PLATE PRODUCT MIX IS DESIGNED FOR:

• Steel and bridge structures• Ship building• Transport machines and vehicles• Abrasion resistant plates• Pressure vessels used in normal, or elevated temperatures• Special military engineering• Plates with improved atmospheric corrosion resistance• Special use (e.g. longitudinally profi led plates)• Flame cut shapes• Pipelines• Offshore structures

QUALITY MANAGEMENT SYSTEM AND ENVIRONMENTAL MANAGEMENT SYSTEM,PRODUCT CERTIFICATION

EVRAZ VÍTKOVICE STEEL, a.s. holds the Quality Management System (QMS) Certifi cate acc. to EN ISO 9001:2000, API Spec. Q1 and Environmental Management System Certifi cate (EMS) acc. to EN ISO 14001:2004.EVRAZ VÍTKOVICE STEEL, a.s. has also certifi cation of its products according to the requirements of classifi cation societies and legislation.

Presentation of the Plates rolling mill

Plates

3

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

PLATES OF STRUCTURAL STEELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

• Plates of steels according to EN 10025-2

• Plates of fi ne-grain steels according to EN 10025-3

• Thermomechanical rolled plates of fi ne-grain steels according to EN 10025-4

• Plates of steels according to ASTM

PLATES OF STRUCTURAL STEELS WITH IMPROVED ATMOSPHERIC CORROSION RESISTANCE (ATMOFIX) . . . . . . . . . . . . . . . . . . . . . 9



PLATES FOR OFFSHORE STRUCTURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

• Plates according to API 2H

THERMOMECHANICAL ROLLED PLATES FOR WELDED PIPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

• Plates for pipes according to API 5L

• Plates for pipes according to EN 10208-2

PLATES FOR SHIP BUILDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

• Plates according to individual shipping companies

• Plates according to A 131

HOT-ROLLED PLATES FOR COLD FORMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

• Thermomechanical rolled plates of steels according to EN 10149-2

• Normalized (rolled) plates of steels according to EN 10149-3

QUENCHED AND TEMPERED PLATES OF 500 Q AND 690 Q STEEL GRADES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

PLATES OF NON ALLOY OR ALLOY STEELS FOR QUENCHING AND TEMPERING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

• Plates of steels according to EN 10083-2 and EN 10083-3

• Plates of steels according to A 827, A 829 and A 830

PLATES WITH MECHANICAL WEAR (ABRASIVE WEAR) RESISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

• Plates of steel according to VN 414320 (ABRAZIT)

PLATES OF STEELS FOR PRESSURE VESSELS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

• Plates of steels for simple pressure vessels according to EN 10207


• Plates of fi ne-grain steels according to EN 10028-3

• Thermomechanical rolled plates of fi ne-grain steels according to EN 10028-5


ARMOUR PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

LONGITUDINALLY PROFILED PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

DELIVERY CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

MATERIAL CERTIFICATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

MARKING OF PLATES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DIMENSIONAL TABLES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

• Table 1 – Maximum available plates length for steels with minimum tensile strength Rm up to 530 MPa

• Table 2 – Maximum available plates length for steels with minimum tensile strength Rm more than 530 MPa

• Table 3 – Maximum available plates length for thermomechanical rolled plates

Contents

4

Introduction

Plates

This catalogue briefl y outlines chemical and mechanical properties of commonly used steel plates.

Properties of commonly used steel plates 1)

Length (max.) 16,000 mm

Width (max.) 3,300 mm

Thickness 2) 5–80 mm

1) All dimensions listed are approximate. Actual plate sizes available depend on the combination of length, width and thickness as well

as on material specifi cation. For particular information, contact EVRAZ VÍTKOVICE STEEL, a.s.

2) Higher thicknesses on agreement

DELIVERY CONDITIONS OF PLATES (HEAT TREATMENT):

AR – As rolledN – NormalizedN+T – Normalized and temperedA – AnnealedM (TMCP) – Thermomechanical rolledQ+T – Quenched and tempered

FOR MORE INFORMATION OR ASSISTANCE REGARDING YOUR STEEL PLATE NEEDS, PLEASE, CONTACT EVRAZ VÍTKOVICE STEEL, a.s.

Phone: +420 595 952 435Fax: +420 595 952 144E-mail: [email protected]

5

Plates of structural steels

PLATES OF STEELS ACCORDING TO EN 10025-2

The most commonly used structural steels having minimum yield strength min. 235 MPa and guaranteed weldability that can be used for low demanding steel structures for bridges, halls, parts of railway and motor vehicles, etc.

DesignationMin. Yield

Strength ReH 2)

[MPa]

TensileStrength Rm

[MPa]

Min. Elongation (L0 = 5.65√S0)

[%]

Min. Impact Energy KV

[°C/J] – longitudinalCEV max. 1) Dimension

Table No.

Max. Thickness for option (C)

[mm]

S235JR(C) 235 360–510 24 +20/27 0.35 1 30

S235J0(C) 235 360–510 24 0/27 0.35 1 30

S235J2(C) 235 360–510 24 -20/27 0.35 1 30

S275JR(C) 275 410–560 21 +20/27 0.40 1 30

S275J0(C) 275 410–560 21 0/27 0.40 1 30

S275J2(C) 275 410–560 21 -20/27 0.40 1 30

S355JR(C) 355 470–630 20 +20/27 0.45 1 30

S355J0(C) 355 470–630 20 0/27 0.45 1 30

S355J2(C) 355 470–630 20 -20/27 0.45 1 30

S355K2(C) 355 470–630 20 -20/40 0.45 1 30

1) CEV C Mn Cr Mo V Ni Cu= + + + + + +6 5 15

; valid for thickness up to 30 mm, for higher thickness refer to the standard

2) Valid for thickness up to 16 mm, for higher thickness refer to the standard

EQUIVALENT DESIGNATION

EN 10025-2 EN 10025+A1 ČSN DIN 17100 BS 4360 NFA 35-501

S235JR(C) S235JRG2(C) 11375 RSt 37 - 2 40 B E 24 - 2

S235J0(C) S235J0(C) 11378 St 37 - 3U 40 C E 24 - 3

S235J2(C) S235J2G4(C) 11378 St 37 - 3N 40 D E 24 - 4

S275JR(C) S275JR(C) 11443 St 44 - 2 43 B E 28 - 2

S275J0(C) S275J0(C) 11445 St 44 - 3U 43 C E 28 - 3

S275J2(C) S275J2G4(C) 11448 St 44 - 3N 43 D E 28 - 4

S355JR(C) S355JR(C) – – 50 B E 36 - 2

S355J0(C) S355J0(C) 11523 St 52 - 3U 50 C E 36 - 3

S355J2(C) S355J2G4(C) – St 52 - 3N 50 D –

S355K2(C) S355K2G4(C) – – 50 DD E 36 - 4

6


Plates

PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-3

Structural steels with guaranteed fi ne-grain structure and low carbon equivalent. Because of the yield strength up to 460 MPa and impact energy guaranteed at temperature -50 °C these steels are suitable for more demanding steel structures and their supporting elements. They are suitable for construction of railway and motor vehicles, too.


Strength ReH 2)

[MPa]

TensileStrength Rm

[MPa]


[%]



Table No.

S275N (NL) 275 370–510 24 -20/40 (-50/27) 0.40 1

S355N (NL) 355 470–630 22 -20/40 (-50/27) 0.43 1

S420N (NL) 420 520–680 19 -20/40 (-50/27) 0.48 1

S460N (NL) 460 550–720 17 -20/40 (-50/27) 0.53 2


; valid for thickness up to 63 mm; for higher thickness refer to the standard



EN 10025-3 EN 10113-2 ČSN DIN 17102

S275N S275N – StE 285

S275NL S275NL 11449 TStE 285

S355N S355N – StE 355

S355NL S355NL 11503 TStE 355

S420N S420N – StE 420

S420NL S420NL 16328 TStE 420

S460N S460N 16229 StE 460

S460NL S460NL – TStE 460

7


THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10025-4

Thermomechanical rolled plates of structural steels having low carbon equivalent, and thus an excellent weldability. They are used for more demanding steel structures and their supporting elements. The impact energy is guaranteed also at temperature -50 °C which facilitates a wide range for their usage.

Designation Min. Yield

Strength ReH 2)

[MPa]

TensileStrength Rm

[MPa]


[%]



Table No.

Max. Thickness

[mm]

S275M (ML) 275 370–530 24 -20/40 (-50/27) 0.34 3 40

S355M (ML) 355 470–630 22 -20/40 (-50/27) 0.39 3 40

S420M (ML) 420 520–680 19 -20/40 (-50/27) 0.43 3 30 3)

S460M (ML) 460 540–720 17 -20/40 (-50/27) 0.45 3 22 3)


; valid for thickness up to 63 mm; for higher thickness refer to the standard


3) Higher thickness on agreement


EN 10025-4 EN 10113-3 SEW 092

S275M S275M –

S275ML S275ML –

S355M S355M QStE 380 TM

S355ML S355ML –


S420ML S420ML –


S460ML S460ML –

8


Plates

PLATES OF STEELS ACCORDING TO ASTM

Designation GradeMin. Yield Strength[MPa]

TensileStrength Rm

[MPa]

Min. Elongation 200/50

[%]

Min. Impact Energy KV 1)

[°C/J] – longitudinal

DimensionTable No.

A 36 250 400–550 20/23 3) 1

A 242 2) 345 480 min. 18/21 3) 1

A 283

A 165 310–415 27/30 3) 1

B 185 345–450 25/28 3) 1

C 205 380–515 22/25 3) 1

D 230 415–550 20/23 3) 1

A 52950 (345) 345 485–690 18/21 3) 1

55 (380) 380 485–690 17/20 3) 1

On agreement, carbon equivalent guarantee is available as per the following formula C Mn Cr Mo V Ni Cu+ + + + + +6 5 15

1) Impact energy testing on agreement

2) This steel is resistant to atmospheric corrosion

3) Testing temperature and minimum impact energy on agreement

FINE-GRAIN STEELS

Designation GradeMin. Yield Strength [MPa]

TensileStrength Rm

[MPa]

Min. Elongation200/50

[%]



DimensionTable No.

A 572(type 1, 2, 3)

42 (290) 290 415 min. 20/24 2) 1

50 (345) 345 450 min. 18/21 2) 1

55 (380) 380 485 min. 17/20 2) 1

60 (415) 415 520 min. 16/18 2) 1

65 (450) 450 550 min. 15/17 2) 2

A 573

58 (400) 220 400–490 21/24 2) 1

65 (450) 240 450–530 20/23 2) 1

70 (485) 290 485–620 18/21 2) 1

A 633

A 290 430–570 18/23 -60/20 1

C 345 485–620 18/23 -60/20 1

D 345 485–620 18/23 -60/20 1

E 415 550–690 18/23 -60/20 2




9

Plates of structural steels with improved atmospheric corrosion resistance (ATMOFIX)

Plates of structural steels with improved atmospheric corrosion resistance do not require – unlike common steels – expensive surface treatments (painting). They feature increased resistance even against impacts of atmosphere which contains sulphur. Their key use is in the area of construction and building of bridges but they can be used for chimney/stack and waste gas ducts structures, too.

PLATES OF STEELS ACCORDING TO 10025-5


Strength ReH 2)

[MPa]

TensileStrength Rm

[MPa]


[%]



Table No.

S235J0W 235 360–510 24 0/27 0.44 1

S235J2W 235 360–510 24 -20/27 0.44 1

S355J0WP 3) 355 470–630 20 0/27 0.52 1

S355J2WP 3) 355 470–630 20 -20/27 0.52 1

S355J0W 355 470–630 20 0/27 0.52 1

S355J2W 355 470–630 20 -20/27 0.52 1

S355K2W 355 470–630 20 -20/40 0.52 1


2) Valid for plates with thickness up to 16 mm, for higher thickness refer to the standard

3) Plates with thickness up to 12 mm only


EN 10025-5 EN 10155 ČSN SEW 087 CAN/CSA – G40.21-M

S235J0W S235J0W – – –

S235J2W S235J2W – WTSt 37 - 3 –

S355J0WP S355J0WP 15217 – –

S355J2WP S355J2WP – – –

S355J0W S355J0W – – –

S355J2W S355J2G2W 15127 WTSt 52 - 3 350AT

S355K2W S355K2G2W – – –


Designation GradeMin. YieldStrength[MPa]

TensileStrength Rm

[MPa]


[%]

Min. ImpactEnergy KV 1)


Dimension Table No.

A 588

A 345 485 min. 18/21 2) 1

B 345 485 min. 18/21 2) 1

C 345 485 min. 18/21 2) 1

K 345 485 min. 18/21 2) 1




10

Plates for offshore structures

Plates

Plates made of the steel grades listed below are used for offshore structures. These steel grades show especially good impact resistance, fatigue resistance and lamellar cracking resistance.

PLATES ACCORDING TO API 2H

GradeMin. YieldStrength[MPa]

TensileStrength Rm

[MPa]


[%]


[°C/J] – transverseCEV max. 1) Dimension

Table No.

42 289 427–565 18/22 -40/270.43 2)

10.45 3)

50345 2)

483–620 16/21 -40/340.43 4)

2324 3) 0.45 5)


2) For width to 2 1⁄2“

3) For width over 2 1⁄2“

4) For width to 2“

5) For width over 2“

11

Thermomechanical rolled plates for welded pipes

Thermomechanical rolled plates of non-alloyed and micro-alloyed steels with excellent weldability, designed exclusively for welded pipelines for combustible and non-combustible fl uids. These can be supplied only upon agreement on the basis of Technical Conditions negotiated between the manufacturer and the customer for supplies of these plates. Technical Conditions must specify all requirements of the customer for the plates subject to the order.

PLATES FOR PIPES ACCORDING TO API 5L 1)

GradeYield

Strength 2) [MPa]

TensileStrength Rm 2)

[MPa]

Min. Elongation 2)

[%]


[°C/J]CEV max. 2) Dimension

Table No.

Max. Thickness 3)

[mm]

B 241–448 414–758 22 0/27 0.40 3 30

X 42 290–496 414–758 21 0/27 0.40 3 30

X 46 317–524 434–758 20 0/27 0.41 3 22

X 52 359–531 455–758 20 0/27 0.41 3 22

X 56 386–544 490–758 18 0/27 0.42 3 22

X 60 414–565 517–758 18 0/27 0.42 3 22

X 65 448–600 531–758 18 0/27 0.43 3 22

X 70 483–621 565–758 18 0/27 0.43 3 22

PLATES FOR PIPES ACCORDING TO EN 10208-2 1)

DesignationYield

Strength Rt0.5 2)

[MPa]


[MPa]

Min. Elongation 2) (L0 = 5.65√S0)

[%]


[°C/J]CEV max. 2) Dimension

Table No.

Max. Thickness 3)

[mm]

L245MB 245–440 415 22 0/40 0.40 3 30

L290MB 290–440 415 21 0/42 0.40 3 30

L360MB 360–510 460 20 0/42 0.41 3 22

L415MB 415–565 520 18 0/51 0.42 3 22

L450MB 450–570 535 18 0/57 0.43 3 22

L485MB 485–605 570 18 0/77 0.43 3 22

1) Standards API 5L and EN 10208 are technical conditions for supplies of welded pipes, not for plates

2) Informative values


EQUIVALENT DESIGNATION ACCORDING TO THE MINIMUM YIELD STRENGTH

API 5L EN 10208-2

B L 245 MB

X 42 L 290 MB

X 52 L 360 MB

X 60 L 415 MB

X 65 L 450 MB

X 70 L 485 MB

12

Plates for ship building

Plates

PLATES ACCORDING TO INDIVIDUAL SHIPPING COMPANIES

Plates of structural steel grades according to the requirements of the inspection companies ABS, BV, DNV, LR, and others, with a yield strength 235 to 355 MPa, are used for ship and watercraft construction. Quality of this assortment is guaranteed by product approbations awarded by individual shipping companies.

Stee

l Gro

up

Min

. Yi

eld

Stre

ngth

ReH

[M

Pa]

Min

. Im

pact

Ene

rgy

KV

[°C/

J] –

long

itudi

nal

ABS

– Am

erica

n Bu

reau

of S

hipp

ing

BV –

Bur

eau

Verit

as

ČLPR

– C

zech

Shi

ppin

g an

d In

dust

rial r

egist

er

GL

– G

erm

anisc

her L

loyd

DNV

– De

t Nor

ske

Verit

as

LR –

Lio

yd's

Reg

ister

of

Shi

ppin

g

RIN

A –

Regi

stro

Ital

iano

Nav

ale

PC –

Mor

skoj

Reg

istr

Sudo

chod

stva

Dim

ensio

n Ta

ble

No.

Nor

mal

Stre

ngth

Stee

l Gra

des

235

– A A A A A A A/24 A 1

0/27 B B B B B B S/24 B 1

-20/27 D D D D D D SS/24 D 1

-40/27 E E E E E E E/24 E 1

High

Stre

ngth

St

eel G

rade

s

315

0/31 AH 32 AH 32 A 32 A 32 A 32 AH 32 S/32 A 32 1

-20/31 DH 32 DH 32 D 32 D 32 D 32 DH 32 SS/32 D 32 1

-40/31 EH 32 EH 32 E 32 E 32 E 32 EH 32 E/32 E 32 1

355

0/34 AH 36 AH 36 A 36 A 36 A 36 AH 36 S/36 A 36 1

-20/34 DH 36 DH 36 D 36 D 36 D 36 DH 36 SS/36 D 36 1

-40/34 EH 36 EH 36 E 36 E 36 E 36 EH 36 E/36 E 36 1


13

Plates for ship building

PLATES ACCORDING TO A 131

Designation GradeMin. Yield Strength[MPa]

TensileStrength Rm

[MPa]


[%]

Min. ImpactEnergy KV


DimensionTable No.

A131

A 235 400–490 21/24 +20/27 1

B 235 400–490 21/24 0/27 1

D 235 400–490 21/24 -10/27 1

E 235 400–490 21/24 -40/27 1

CS 235 400–490 21/24 -40/27 1

DS 235 400–490 21/24 -10/27 1

AH 32 315 470–585 19/22 0/34 1

DH 32 315 470–585 19/22 -20/34 1

EH 32 315 470–585 19/22 -40/34 1

AH 36 360 490–620 19/22 0/34 1

DH 36 360 490–620 19/22 -20/34 1

EH 36 360 490–620 19/22 -40/34 1


14

Hot-rolled plates for cold forming

Plates

THERMOMECHANICAL ROLLED PLATES OF STEELS ACCORDING TO EN 10149-2

Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating. These plates have excellent weldability because of low carbon equivalent.


Strength ReH [MPa]

Tensile Strength Rm

[MPa]


[%]



TransverseBend Test 2)

DimensionTable No.

Max. Thickness

[mm]

S315MC 315 390–510 24 -20/40 0 t 3 20

S355MC 355 430–550 23 -20/40 0.5 t 3 20

S420MC 420 480–620 19 -20/40 0.5 t 3 20

S460MC 460 520–670 17 -20/40 1 t 3 20

S500MC 500 550–700 14 -20/40 1 t 3 16

S550MC 550 600–760 14 -20/40 1.5 t 3 16



2) Minimum former diameter for 180° bend angle; t – plate thickness


EN SEW 092 (1990)

S315MC (QStE 340 TM)

S355MC (QStE 380 TM)

S420MC QStE 420 TM

S460MC QStE 460 TM

S500MC QStE 500 TM

S550MC QStE 550 TM

15

Hot-rolled plates for cold forming

NORMALIZED (ROLLED) PLATES OF STEELS ACCORDING TO EN 10149-3

These plates guarantee suitability for cold forming because of their technological processing. Standard methods used for processing these plates are bending, fl anging, cold roll forming, etc. Based on agreement these plates can be delivered in the condition suitable for hot-dip zinc-coating.


Strength ReH[MPa]

Tensile Strength Rm

[MPa]


[%]



TransverseBend Test 2)

DimensionTable No.

Max. Thickness

[mm]

S260NC 260 370–490 30 -20/40 0 t 1 20

S315NC 315 430–550 27 -20/40 0.5 t 1 20

S355NC 355 470–610 25 -20/40 0.5 t 1 20

S420NC 420 530–670 23 -20/40 0.5 t 2 20



2) Minimum former diameter for 180° bend angle; t – plate thickness


EN SEW 092

S260NC QStE 260N

S315NC (QStE 340N)

S355NC (QStE 380N)

S420NC QStE 420N

16

Quenched and tempered plates of 500 Q and 690 Q steel grades

Plates

QUENCHED AND TEMPERED PLATES OF 500 Q AND 690 Q STEEL GRADES

Quenched and tempered plates of 500 Q and 690 Q steel grades are supplied in the form suitable for steel structures (S500 …, S690 …) as per EN 10025-6 or in the form suitable for pressure vessels (P500…, P690…) as per EN 10028-6.

Designation as per EN 10025-6: S500 Q, S500 QL, S500 QL1, S690 Q, S690 QL, S690 QL1.Designation as per EN 10028-6: P500 Q, P500 QH, P500 QL1, P500 QL2, P690 Q, P690 QH, P690 QL1, P690 QL2.

PARAMETERS FOR PLATES PURCHASE ORDER

Thickness 20–80 mm

Width 1) 1,000–2,500 mm

Length max. 11,000 mm

Weight of one piece of plate max. 8,000 kg

Total volume of plates ordered multiples of 50 t

1) Higher width on agreement

MECHANICAL PROPERTIES AND CARBON EQUIVALENT


Strength ReH 1) [MPa]

Min. YieldStrength Rp0.2 2)

[MPa]

Tensile Strength Rm 1)

[MPa]

Min. Elongation (L0=5.65√S0)

[%]


[°C/J] – transverseCEV max. 4)

S500 Q 500 – 590–770 17 -20/27 0.47

S500 QL 500 – 590–770 17 -40/27 0.47

S500 QL1 500 – 590–770 17 -60/27 0.47

P500 Q 500 – 590–770 17 -20/27 –

P500 QH 500 380 590–770 17 -20/27 –

P500 QL1 500 380 590–770 17 -40/27 –

P500 QL2 500 380 590–770 17 -60/27 –

S690 Q 690 – 770–940 14 -20/27 0.65

S690 QL 690 – 770–940 14 -40/27 0.65

S690 QL1 690 – 770–940 14 -60/27 0.65

P690 Q 690 – 770–940 14 -20/27 –

P690 QH 690 570 770–940 14 -20/27 –

P690 QL1 690 570 770–940 14 -40/27 –

P690 QL2 690 570 770–940 14 -60/27 –

1) Valid for thickness ≤ 50 mm, for higher thickness refer to the standard

2) On agreement; valid for temperature 300 °C and thickness ≤ 50 mm; for other temperatures (lower)

or higher thickness refer to the standard EN 10028-6

3) For other temperatures (higher) refer to the standard


; only for plates supplied as per EN 10025-6; valid for thickness ≤ 50 mm;

for higher thickness refer to the standard EN 10025-6

17

Plates of non alloy or alloy steels for quenching and tempering

PLATES OF STEELS ACCORDING TO EN 10083-2 AND EN 10083-3

They are used for machinery parts in all machinery production areas. These plates are diffi cult for welding in most cases. They are supplied in soft annealed (+A) or normalized (+N) condition according to the following table. Products of these plates are further processed with heat treatment (usually quenching and tempering), after such treatment they obtain their typical properties, i.e. high toughness, hardness and strength.


Strength ReH 1)

[MPa]

Min. Tensile Strength Rm 1)

[MPa]

Min. Elongation 1) (L0 = 5.65√S0)

[%]

HB max.(+A)

Dimensiontable No.

C22E 2) 240 430 24 – 1C35/C35E 2) 300 550 18 – 2C40/C40E 2) 320 580 16 – 2C45/C45E 2) 340 620 14 207 2

C50E 2) 355 650 13 217 2C55/C55E 2) 370 680 11 229 2C60/C60E 2) 380 710 10 241 2

28Mn6 2) 345 630 17 223 238Cr2 3) – – – 207 246Cr2 3) – – – 223 234Cr4 3) – – – 223 237Cr4 3) – – – 235 241Cr4 3) – – – 241 2

25CrMo4 3) – – – 212 234CrMo4 3) – – – 223 242CrMo4 3) – – – 241 250CrMo4 3) – – – 248 2

34CrNiMo6 3) – – – 248 230CrNiMo8 3) – – – 248 2

35NiCr6 3) – – – 223 239NiCrMo3 3) – – – 240 2

1) Valid for plates in normalized condition and for thickness up to 16 mm, for higher thickness refer to the standard

2) EN 10083-2

3) EN 10083-3


EN Germany ČSN Great Britain France

C22E CK22 12024 070M20 XC18C35/C35E C35/CK35 12040 080M36 XC38H1C40/C40E C40/CK40 12041 080M40 XC42H1C45/C45E C45/CK45 12050 080M46 XC48H1

C50E CK50 12051 080M50 –C55/C55E C55/CK55 12060 070M55 XC55H1C60/C60E C60/CK60 12061 070M60 –

28Mn6 28Mn6 13141 150M19 –38Cr2 38Cr2 – – 38C246Cr2 46Cr2 – – –34Cr4 34Cr4 – 530M32 32C437Cr4 37Cr4 14140 530M36 38C441Cr4 41Cr4 – 530M40 42C4

25CrMo4 25CrMo4 15130 708M25 25CD434CrMo4 34CrMo4 15131 708M32 34CD442CrMo4 42CrMo4 15142 708M40 42CD450CrMo4 50CrMo4 – 708M50 –

34CrNiMo6 34CrNiMo6 16343 817M40 –30CrNiMo8 30CrNiMo8 16430 823M30 30CND8

35NiCr6 35NiCr6 – – –39NiCrMo3 – – – –

18

Plates of non alloy or alloy steels for quenching and tempering

Plates

Designation Grade(SAE Number)

Dimension table

number

A 827

1009 1

1020 1

1035 2

1040 2

1045 2

1050 2

A 829

1330 2

1335 2

1340 2

1345 2

4118 2

4130 2

4135 2

4137 2

4140 2

4142 2

4145 2

4150 2

4615 2

4617 2

4620 2

8615 2

8617 2

9620 2

8622 2

8625 2

8627 2

8630 2

8637 2

8640 2

8742 2

Heat treatment and mechanical properties

on agreement.

PLATES OF STEELS ACCORDING TO A 827, A 829, A 830

Designation Grade(SAE Number)

Dimension table

number

A 830

1006 1

1008 1

1009 1

1010 1

1012 1

1015 1

1016 1

1017 1

1018 1

1019 1

1020 1

1021 1

1022 1

1023 1

1025 1

1026 1

1030 1

1033 1

1035 2

1037 2

1038 2

1039 2

1040 2

1042 2

1043 2

1045 2

1046 2

1049 2

1050 2

1055 2

1060 2

1524 2

1527 2

1536 2

1541 2

1548 2

1552 2

19

Plates with mechanical wear (abrasive wear) resistance

PLATES OF STEEL ACCORDING TO VN 414320 (ABRAZIT)

Grade 14320 is fi ne-grain steel which is used for rolling of plates for production of parts exposed to extreme abrasion and mechanical wear.

These plates can be used for transport routes and chutes for gravel, stone, coal, cement etc. Resistance against abrasion, and hardness are guaranteed either in the condition without heat treatment (so called as rolled – 14320.0), or after quenching.

Machining in the condition without heat treatment (14320.0) is diffi cult; in the soft annealed condition (14320.3) it is good. Cold forming is not possible, hot forming at temperature of 850–1,150 °C is good.

Joints between parts are usually made as bolted joints; or in the form of fi xing welds, using preheating up to 200 °C at minimum (thickness up to 10 mm without preheating); however the welded joint does not reach the strength of the parent base. Cutting plates by means of fl ame cutting, or fl ame cutting shaped plates is also performed with preheating up to 200 °C at minimum. Shearing is not recommended for plate cutting.

These plates can be delivered as semi-trimmed plates having thickness from 8 to 25 mm in the condition without heat treatment (14320.0), or from 8 to 30 mm in the soft annealed condition (14320.3). Other thickness and dimension on agreement.

Tensile strength (Rm) in the condition without heat treatment (14320.0) is approx. 930 to 1,370 MPa, the lowest yield strength (ReH) is approx. 75 % of the tensile strength, the lowest elongation (A5) is 8 % and Brinell hardness is approx. 270 to 400 HB. Tensile strength can be improved to approx. 1,400 MPa by quenching. Tensile strength, yield strength, and elongation are not subject to testing and acceptance inspections because test samples are diffi cult to be made.

In the soft annealed condition (14320.3) the Brinell hardness is max. 260 HB.

20

Plates of steels for pressure vessels

Plates

PLATES OF STEELS FOR SIMPLE PRESSURE VESSELS ACCORDING TO EN 10207

Plates with low yield strength for simple pressure vessels and storage facilities, e.g. for compressed air or other fl uids operating under normal outdoor temperatures.


Strength ReH 1)

[MPa]

Min. Yield Strength Rp0.2 2)

[MPa]

TensileStrength Rm

[MPa]

Min. Elongation(L0 = 5.65√S0)

[%]



DimensionTable No.

P235S 235 117 360–480 26 -20/28 1

P265S 265 140 410–530 22 -20/28 1

P275SL 275 132 390–510 24 -50/28 1


2) Valid for temperature 300 °C, for other temperatures (lower) refer to the standard

21


PLATES OF STEELS ACCORDING TO EN 10028-2

Plates of unalloyed as well as alloyed steels for pressure loaded vessels and facilities, operating under normal as well as elevated tempera-tures. These plates are usually delivered in normalized condition or in normalized and tempered condition.

Designation Min. Yield

Strength ReH 1)

[MPa]

Min. Yield Strength Rp0,2 2)

[MPa]

TensileStrength Rm

[MPa]


[%]


[°C/J] – transverse

DimensionTable No.

P235GH 4) 235 153 360–480 24 -20/27 1

P265GH 4) 265 173 410–530 22 -20/27 1

P295GH 4) 295 192 460–580 21 -20/27 1

P355GH 4) 355 232 510–650 20 -20/27 1

16Mo3 275 194 440–590 22 +20/31 1

18MnMo4-5 345 285 510–650 20 -20/27 1

15NiCuMoNb5-6-4 460 380 610–780 16 -20/27 2

13CrMo4-5 300 216 450–600 19 +20/31 1

13CrMoSi5-5 310 233 510–690 20 0/27 1

10CrMo9-10 310 236 480–630 18 +20/31 1

12CrMo9-10 355 295 540–690 18 -20/27 2


2) On agreement; valid for temperature 300 °C and thickness up to 16 mm; for other temperatures or higher thickness refer to the standard

3) For other temperatures refer to the standard or on agreement

4) Maximum value of the carbon equivalent on agreement when ordering for steels P235GH, P265GH, P295GH and P355GH based

on the following formula C Mn Cr Mo V Ni Cu+ + + + + +6 5 15


EN ČSN DIN 17155

P235 GH 11368 H I

P265 GH 11418 H II

P295 GH 13030 (11478) 17Mn4

P355 GH 11523 19Mn6

16Mo3 15020 15Mo3

13CrMo4-5 15121 13CrMo44

10CrMo9-10 15313 10CrMo910

18MnMo4-5 15223 (15219) –

22


Plates

PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-3

These steels feature guaranteed fi ne-grain structure and low carbon equivalent. Mechanical properties of these plates are guaranteed at high temperatures (up to 400 °C) – yield strength Rp0,2 as well as at low temperatures (down to -50 °C) – impact energy KV; therefore, they can be used for constructions of more demanding pressure vessels working under high as well as low temperatures.


Strength ReH 1)

[MPa]

Min. YieldStrength Rp0.2 2)

[MPa]

Tensile Strength Rm

[MPa]

Min. Elongation(L0 = 5.65√S0)

[%]

Min. ImpactEnergy KV 3)


Table No.

P275NH 275 179 390–510 24 -20/30 0.40 1

P275NL1 275 179 390–510 24 -40/27 0.40 1

P275NL2 275 179 390–510 24 -50/27 0.40 1

P355N 355 – 490–630 22 -20/30 0.43 1

P355NH 355 232 490–630 22 -20/30 0.43 1

P355NL1 355 232 490–630 22 -40/27 0.43 1

P355NL2 355 232 490–630 22 -50/27 0.43 1

P460NH 460 300 570–720 17 -20/30 0.53 2

P460NL1 460 300 570–720 17 -40/27 0.53 2

P460NL2 460 300 570–720 17 -50/27 0.53 2


2) On agreement; valid for temperature 300 °C and thickness up to 16 mm, for other temperatures or higher thickness refer to the standard

3) For other temperatures refer to the standard

4) On agreement; CEV C Mn Cr Mo V Ni Cu= + + + + + +6 5 15



EN ČSN DIN 17102

P275NH 11448 WStE 285

P275NL1 11449 TStE 285

P275NL2 – EStE 285

P355N – StE 355

P355NH – WStE 355

P355NL1 11503 TStE 355

P355NL2 – EStE 355

P460NH – WStE 460

P460NL1 – TStE 460

P460NL2 – EStE 460

23


THERMOMECHANICAL ROLLED PLATES OF FINE-GRAIN STEELS ACCORDING TO EN 10028-5

Thermomechanical rolled plates having higher yield strength up to 460 MPa are designed for pressure vessels and facilities working under normal or low temperatures. These plates have excellent weldability because of low carbon equivalent. Impact energy is guaranteed even at temperature -50 °C.


Strength ReH[MPa]

TensileStrength Rm

[MPa]


[%]



Table No.

Max. Thickness

[mm]

P355M 355 1) 450–610 22 -20/27 0.39 3 40

P355ML1 355 1) 450–610 22 -40/27 0.39 3 40

P355ML2 355 1) 450–610 22 -50/27 0.39 3 40

P420M 420 2) 500–660 19 -20/27 0.43 3 30 5)

P420ML1 420 2) 500–660 19 -40/27 0.43 3 30 5)

P420ML2 420 2) 500–660 19 -50/27 0.43 3 30 5)

P460M 460 2) 530–720 17 -20/27 0.45 3 22 5)

P460ML1 460 2) 530–720 17 -40/27 0.45 3 22 5)

P460ML2 460 2) 530–720 17 -50/27 0.45 3 22 5)



3) For other temperatures refer to the standard

4) On agreement; CEV C Mn Cr Mo V Ni Cu= + + + + + +6 5 15



24


Plates



TensileStrength Rm

[MPa]


[%]



DimensionTable No.

A 202A 310 515–655 16/19 2) 1B 325 585–760 15/18 2) 2

A 204A 255 450–585 19/23 2) 1B 275 485–620 17/21 2) 1C 295 515–655 16/20 2) 1

A 285A 165 310–450 27/30 4/14 1B 185 345–485 25/28 10/14 1C 205 380–515 23/27 16/14 1

A 387

2 310 485–620 18/22 2) 111 310 515–690 18/22 2) 112 275 450–585 19/22 2) 122 310 515–690 –/18 2) 1

A 455 260 515–655 15/22 -4/18 1

A 51560 (415) 220 415–550 21/25 2) 165 (450) 240 450–585 19/23 2) 170 (485) 260 485–620 17/21 2) 1




FINE-GRAIN STEELS


TensileStrength Rm

[MPa]


[%]



DimensionTable No.

A 225 D 415 550–725 17/19 2) 2A 299 290 515–655 16/19 -7/20 1

A 302

A 310 515–655 15/19 2) 1B 345 550–690 15/18 2) 2C 345 550–690 17/20 2) 2D 345 550–690 17/20 2) 2

A 516

55 (380) 205 380–515 23/27 -51/18 160 (415) 220 415–550 21/25 -51/18 165 (450) 240 450–585 19/23 -51/18 170 (485) 260 485–620 17/21 -46/20 1

A 537 class 1 345 485–620 18/22 -62/20 1A 612 345 570–725 16/22 -46/27 2

A 662A 275 400–540 20/23 -60/18 1B 275 450–585 20/23 -51/18 1C 295 485–620 18/22 -46/20 1

A 737B 345 485–620 18/23 2) 1C 415 550–690 18/23 2) 2




25

Armour plates

Plates of armour steels are manufactured in several degrees of hardness, or shooting resistance. Armours of middle hardness are used mostly for armouring heavy vehicles; armours of high hardness are used for lightweight military vehicles, resistant mainly against infantry weapons. Armour plates of martenzitic steels can be welded utilizing usually manual arc welding or automatic submerged-arc welding methods. An advantageous method is shielded welding.


Strength ReH 1)

[MPa]


[MPa]

Min. Elongation 1)

(L0 = 5.65√S0)[%]

CEV 2) HB Hardness Condition after heat treatment

Dimensiontable No.

43 PSM (A)49 S (A)

42 SM (A)52 S (A)

400 600 25

0.95

180–250 soft annealed

2

850 1 050 7 280–340 heat treated

2 P (A)V 2–9

450 650 250.65

200–250 soft annealed2

1 200 1 400 10 370–430 heat treated

Armox 500 S450 650 25

0.75200–250 soft annealed

21 500 1 700 8 450–550 heat treated

1) approximate values

2) CEV values for information only

26

Longitudinally profiled plates

Plates

Longitudinally profi led plates (also tapered plates) are plates whose thickness varies along their longitudinal axis, with the thickness variation reached by continuous adjusting of the roll gap when the material passes through the roll stand. Longitudinally profi led plates can generally have linear or non-linear thickness course.

Tapered plates are used especially for various types of steel structures where their usage results in consider-able economical savings (structure weight reduction, reduction of welded joints, etc.)

In order to reach as much economical contribution as possible, and easy application in all steel structures, various shapes of tapered plates consisting of several tapered and fl at segments can be manufactured and used.

Tapered plates are manufactured of steels according to the standards EN 10025-2 and EN 10025-3.

The dimensional standard applicable for longitudinally profi led plates is VN 425321.

BASIC PARAMETERS OF LONGITUDINALLY PROFILED PLATES

Plate thickness 15–80 mm

Max. wedge shapes 5 mm/1 m

Max. thickness difference 40 mm

Min. length of tapered part 1,000 mm

Max. number of segments having different thickness 5

Plate width 1,000–3,000 mm

Max. plate length depends on shape, dimensions with respect to the maximum weight

Max. plate weight 8,700 kg

BASIC TYPES OF LONGITUDINALLY PROFILED PLATES

27

Delivery conditions

APPLICABLE STANDARDS

Dimension, fl atness EN 10029, A(SA)20/A(SA)20M, A(SA)6/A(SA)6M

Surface EN 10163

Ultrasound EN 10160, SEL 072/77, A(SA)435, A(SA)578, other standards on agreement

Certifi cates EN 10204

Testing as per EN, ASTM, ASME, shipping company standards, other standards on agreement

INTERNAL SOUNDNESS HOMOGENEITY ULTRASONIC TESTING

Automatic ultrasonic TÜV NORD certifi ed line is used or manual testing is available to meet stricter conditions.

28

QUALITY ASSURANCE CERTIFICATES AS PER EN 10204 : 2004

Quality Assurance certifi cates shall be issued by the Quality Assurance Department stating chemical composition of heat and material testing results (e.g. ultrasound, mechanical testing) as required by the customer:

Customer Order Compliance Declaration “2.1”The document is issued by the manufacturer to certify that the products delivered comply with customer order requirements. The document does not state any test results.

Testing Protocol “2.2”The document is issued by the manufacturer to certify that products delivered comply with customer order requirements. The document states general test results.

Inspection Certificate “3.1”This is a document issued by the manufacturer in which the manufacturer confi rms that the products supplied are in line with the requirements of the order and in which the manufacturer indicates the results of the tests.The testing unit and the tests executed are indicated in the product’s specifi cation, in the offi cial specifi cations, in the corresponding technical specifi cations and/or in the order.The document is confi rmed by an authorized representative of the manufacturer independent of the production units.In the Inspection Certifi cate “3.1”, the manufacturer may indicate the results of tests obtained from testing as specifi ed by the specifi cation on the basic materials or input products used on condition that the manufacturer uses tracing procedures and can provide the necessary corresponding inspection documents.

Inspection Certificate “3.2”This is a document prepared by an authorized representative of the manufacturer independent of the production units and either by an authorized representative of the client (inspection company) or by an inspector indicated in the offi cial specifi cations in which they declare that the products supplied are in line with the requirements of the order and which indicates the results of the tests.In the Inspection Certifi cate “3.2”, the manufacturer may indicate the results of tests obtained from testing as specifi ed by the specifi cation on the basic materials or input products used on condition that the manufacturer uses tracing procedures and can provide the necessary corresponding inspection documents.

Inspection Companiesa) national: ŘJ, ČD, ZVS, INSPEKTA, ČLPR, and othersb) international: LR, DNV, ABS, BV, GL, TÜV, RINA, Russian Naval Register of Shipping, and othersc) inspection carried out directly by the customer

Multiple certifi cation available on agreement.

Material certificates

Plates

29

Product marking is performed by stamping and painting. A punch for stamping in cold condition is used for marking of plates (Four-High Mill) in low-stress spot method. Manual low-stress stamping (Two-High Mill) the low-stress method has to be agreed in the order. White paint marking is carried out with automatic marking machines, or manually (usually using templates). In case of any specifi c customer‘s requirement for a special plate marking, either in the form of a text (sprayed with white color on the plate), or in the form of color marking, marking is carried out within the frame of each individual order based on agreement. The “Colour Marking Catalogue” containing individual patterns is available to make the color marking easier.

EXAMPLE OF PLATE MARKING WITH COLD STAMPING

EXAMPLE OF PLATE MARKING WITH COLOUR

Rolled product No. Plate serial No. from the rolled product Manufacturer’s symbol Heat origin Heat No.

Steel grade (and/or heat treatment code) Sample No.

Plate widthRolled product No. Heat origin Heat no. Plate serial No. from the rolled product

Internal localization code

Heat treatmentcode

Order No.

Plate thickness

Steel grade

Inspection Plate length

Marking of plates

width [mm] thickness [mm]

1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001

1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100

5 12 10 10 12 12 12 12 12

6 12 12 12 10 10 10 12 12 12 12 12 12

7 14 14 14 14 14 14 14 14 14 14 14 14

8 15 15 15 15 15 15 15 15 15 15 15 15

9 16 16 16 16 16 16 16 16 16 16 16 16

10 16 16 16 16 16 16 16 16 16 16 16 16

11 16 16 16 16 16 16 16 16 16 16 16 16

12 16 16 16 16 16 16 16 16 16 16 16 16

13 16 16 16 16 16 16 16 16 16 16 16 16

14 16 16 16 16 16 16 16 16 16 16 16 16

15 16 16 16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 16 16 16 16

17 16 16 16 16 16 16 16 16 16 16 16 16

18 16 16 16 16 16 16 16 16 16 16 16 16

19 16 16 16 16 16 16 16 16 16 16 16 16

20 16 16 16 16 16 16 16 16 16 16 16 16

21 16 16 16 16 16 16 16 16 16 16 16 16

22 16 16 16 16 16 16 16 16 16 16 16 16

23 16 16 16 16 16 16 16 16 16 16 16 16

24 16 16 16 16 16 16 16 16 16 16 16 16

25 16 16 16 16 16 16 16 16 16 16 16 16

26 16 16 16 16 16 16 16 16 16 16 16 16

28 16 16 16 16 16 16 16 16 16 16 16 16

30 16 16 16 16 16 16 16 16 16 16 16 16

32 16 16 16 16 16 16 16 16 16 16 16 15

34 16 16 15 16 16 16 16 16 16 16 15 14

36 16 16 15 16 16 16 16 16 16 15 14 13

38 16 16 14 16 16 15 16 16 15 14 13 12

40 16 15 13 16 15 14 16 15 14 13 12 12

42 16 14 12 16 14 13 15 14 13 12 12 11

44 15 13 12 15 14 13 14 13 13 12 11 11

46 14 13 11 14 13 12 14 13 12 11 11 10

48 14 12 11 14 13 12 13 12 11 11 10 10

50 13 12 10 13 12 11 12 12 11 10 10 9

52 12 11 10 12 11 11 12 11 10 10 9 9

54 12 11 9 12 11 10 11 11 10 9 9 8

56 11 10 9 11 11 10 11 10 10 9 9 8

58 11 10 9 11 10 9 11 10 9 9 8 8

60 11 10 8 11 10 9 10 9 9 8 8 7

65 10 9 8 10 9 8 9 9 8 8 7 7

70 9 8 7 9 8 8 9 8 7 7 7 6

75 8 7 6 8 8 7 8 7 7 7 6 6

80 8 7 6 8 7 7 7 7 6 6 6 5

Other plate dimensions on agreementPlates of some steels (type S/P235…, S/P355…) according to EN 10025-2, EN 10025-3, EN 10028-2, EN 10028-3can be ordered in a piece weight up to 12,500 kg and in a thickness up to 102 mm; dimensions on agreement

TABLE 1 – MAXIMUM AVAILABLE PLATES LENGTH FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm up to 530 MPa

2,101 2,201 2,301 2,401 2,501 2,601 2,701 2,801 2,901 3,001 3,101 3,201 width [mm]thickness [mm]2,200 2,300 2,400 2,500 2,600 2,700 2,800 2,900 3,000 3,100 3,200 3,300

10 10 10 10 10 5

12 12 12 12 12 10 10 10 10 6

14 14 14 14 14 13 13 12 12 7

15 15 15 15 15 15 15 15 15 15 8

16 16 16 16 16 16 16 16 16 16 16 16 9

16 16 16 16 16 16 16 16 16 16 16 16 10

16 16 16 16 16 16 16 16 16 16 16 16 11

16 16 16 16 16 16 16 16 16 16 16 16 12

16 16 16 16 16 16 16 16 16 16 16 16 13

16 16 16 16 16 16 16 16 16 16 16 16 14

16 16 16 16 16 16 16 16 16 16 16 16 15

16 16 16 16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 16 16 16 17

16 16 16 16 16 16 16 16 16 16 16 16 18

16 16 16 16 16 16 16 16 16 16 16 16 19

16 16 16 16 16 16 16 16 16 16 16 15 20

16 16 16 16 16 16 16 16 16 15 15 14 21

16 16 16 16 16 16 16 16 15 15 14 14 22

16 16 16 16 16 16 16 15 15 14 14 13 23

16 16 16 16 16 16 15 14 14 13 13 13 24

16 16 16 16 15 15 14 14 13 13 12 12 25

16 16 16 15 15 14 14 13 13 12 12 11 26

16 16 15 14 14 13 13 12 12 11 11 11 28

15 15 14 13 13 12 12 11 11 11 10 10 30

14 14 13 12 12 11 11 11 10 10 9 9 32

13 13 12 12 11 11 10 10 9 9 9 9 34

13 12 11 11 10 10 10 9 9 9 8 8 36

12 11 11 10 10 9 9 9 8 8 8 8 38

11 11 10 10 9 9 9 8 8 8 7 7 40

11 10 10 9 9 8 8 8 7 7 7 7 42

10 10 9 9 8 8 8 7 7 7 7 6 44

10 9 9 8 8 8 7 7 7 7 6 6 46

9 9 8 8 8 7 7 7 6 6 6 6 48

9 8 8 8 7 7 7 6 6 6 6 5 50

8 8 8 7 7 7 6 6 6 6 5 5 52

8 8 7 7 7 6 6 6 6 5 5 5 54

8 7 7 7 6 6 6 6 5 5 5 5 56

7 7 7 6 6 6 6 5 5 5 5 5 58

7 7 6 6 6 6 5 5 5 5 5 60

6 6 6 6 5 5 5 5 65

6 6 5 5 5 5 70

5 5 5 5 75

5 5 5 80


1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001

1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100

5 10 10 10 10 10 10 10 10

6 12 12 12 10 10 10 12 12 12 12 12 12

7 12 12 12 14 14 14 14 14 14 14 14 14

8 14 14 14 14 14 14 14 14 14 14 14 14

9 15 16 16 16 16 16 16 16 16 16 16 16

10 16 16 16 16 16 16 16 16 16 16 16 16

11 16 16 16 16 16 16 16 16 16 16 16 16

12 16 16 16 16 16 16 16 16 16 16 16 16

13 16 16 16 16 16 16 16 16 16 16 16 16

14 16 16 16 16 16 16 16 16 16 16 16 16

15 16 16 16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 16 16 16 16

17 16 16 16 16 16 16 16 16 16 16 16 16

18 16 16 16 16 16 16 16 16 16 16 16 16

19 16 16 16 16 16 16 16 16 16 16 16 16

20 16 16 16 16 16 16 16 16 16 16 16 16

21 16 16 16 16 16 16 16 16 16 16 16 16

22 16 16 16 16 16 16 16 16 16 16 16 16

23 16 16 16 16 16 16 16 16 16 16 16 16

24 16 16 16 16 16 16 16 16 16 16 16 16

25 16 16 16 16 16 16 16 16 16 16 16 16

26 16 16 16 16 16 16 16 16 16 16 16 16

28 16 16 16 16 16 16 16 16 16 16 16 16

30 16 16 16 16 16 16 16 16 16 16 16 16

32 16 16 16 16 16 16 16 16 16 16 16 15

34 16 16 15 16 16 16 16 16 16 16 15 14

36 16 16 15 16 16 16 16 16 16 15 14 13

38 16 16 14 16 16 15 16 16 15 14 13 12

40 16 15 13 16 15 14 16 15 14 13 12 12

42 16 14 12 16 14 13 15 14 13 12 12 11

44 15 13 12 15 14 13 14 13 13 12 11 11

46 14 13 11 14 13 12 14 13 12 11 11 10

48 14 12 11 14 13 12 13 12 11 11 10 10

50 13 12 10 13 12 11 12 12 11 10 10 9

52 12 11 10 12 11 11 12 11 10 10 9 9

54 12 11 9 12 11 10 11 11 10 9 9 8

56 11 10 9 11 11 10 11 10 10 9 9 8

58 11 10 9 11 10 9 11 10 9 9 8 8

60 11 10 8 11 10 9 10 9 9 8 8 7

65 10 9 8 10 9 8 9 9 8 8 7 7

70 9 8 7 9 8 8 9 8 7 7 7 6

75 8 7 6 8 8 7 8 7 7 7 6 6

80 8 7 6 8 7 7 7 7 6 6 6 5

Other plate dimensions on agreement

TABLE 2 – MAXIMUM AVAILABLE PLATES LENGTH FOR STEELS WITH MINIMUM TENSILE STRENGTH Rm more than 530 MPa

2,101 2,201 2,301 2,401 2,501 2,601 2,701 2,801 2,901 3,001 3,101 3,201 width [mm]thickness [mm]2,200 2,300 2,400 2,500 2,600 2,700 2,800 2,900 3,000 3,100 3,200 3,300

10 10 10 10 10 5

12 12 12 12 12 10’ 10’ 10’ 10’ 6

14 14 14 12 12 10 10 10 10 7

14 14 14 14 14 13 13 13 13 12 8

16 16 16 14 14 13 13 13 13 12 12 12 9

16 16 16 16 16 16 16 16 16 16 16 16 10

16 16 16 16 16 16 16 16 16 16 16 16 11

16 16 16 16 16 16 16 16 16 16 16 16 12

16 16 16 16 16 16 16 16 16 16 16 16 13

16 16 16 16 16 16 16 16 16 16 16 16 14

16 16 16 16 16 16 16 16 16 16 16 16 15

16 16 16 16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 16 16 16 17

16 16 16 16 16 16 16 16 16 16 16 16 18

16 16 16 16 16 16 16 16 16 16 16 16 19

16 16 16 16 16 16 16 16 16 16 16 15 20

16 16 16 16 16 16 16 16 16 15 15 14 21

16 16 16 16 16 16 16 16 15 15 14 14 22

16 16 16 16 16 16 16 15 15 14 14 13 23

16 16 16 16 16 16 15 14 14 13 13 13 24

16 16 16 16 15 15 14 14 13 13 12 12 25

16 16 16 15 15 14 14 13 13 12 12 11 26

16 16 15 14 14 13 13 12 12 11 11 11 28

15 15 14 13 13 12 12 11 11 11 10 10 30

14 14 13 12 12 11 11 11 10 10 9 9 32

13 13 12 12 11 11 10 10 9 9 9 9 34

13 12 11 11 10 10 10 9 9 9 8 8 36

12 11 11 10 10 9 9 9 8 8 8 8 38

11 11 10 10 9 9 9 8 8 8 7 7 40

11 10 10 9 9 8 8 8 7 7 7 7 42

10 10 9 9 8 8 8 7 7 7 7 6 44

10 9 9 8 8 8 7 7 7 7 6 6 46

9 9 8 8 8 7 7 7 6 6 6 6 48

9 8 8 8 7 7 7 6 6 6 6 5 50

8 8 8 7 7 7 6 6 6 6 5 5 52

8 8 7 7 7 6 6 6 6 5 5 5 54

8 7 7 7 6 6 6 6 5 5 5 5 56

7 7 7 6 6 6 6 5 5 5 5 5 58

7 7 6 6 6 6 5 5 5 5 5 60

6 6 6 6 5 5 5 5 65

6 6 5 5 5 5 70

5 5 5 5 75

5 5 5 80

TABLE 3 – MAXIMUM AVAILABLE PLATES LENGTH FOR THERMOMECHANICAL ROLLED PLATES


1,001 1,101 1,251 1,301 1,401 1,501 1,601 1,701 1,801 1,901 2,001

1,000 1,100 1,250 1,300 1,400 1,500 1,600 1,700 1,800 1,900 2,000 2,100

8 14 14 14 14 14 14 14 14 14 14 14 14

9 15 16 16 16 16 16 16 16 16 16 16 16

10 16 16 16 16 16 16 16 16 16 16 16 16

11 16 16 16 16 16 16 16 16 16 16 16 16

12 16 16 16 16 16 16 16 16 16 16 16 16

13 16 16 16 16 16 16 16 16 16 16 16 16

14 16 16 16 16 16 16 16 16 16 16 16 16

15 16 16 16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 16 16 16 16

17 16 16 16 16 16 16 16 16 16 16 16 16

18 16 16 16 16 16 16 16 16 16 16 16 16

19 16 16 16 16 16 16 16 16 16 16 16 16

20 16 16 16 16 16 16 16 16 16 16 16 16

21 16 16 16 16 16 16 16 16 16 16 16 16

22 16 16 16 16 16 16 16 16 16 16 16 16

23 16 16 16 16 16 16 16 16 16 16 16 16

24 16 16 16 16 16 16 16 16 16 16 16 16

25 16 16 16 16 16 16 16 16 16 16 16 16

26 16 16 16 16 16 16 16 16 16 16 16 16

28 16 16 16 16 16 16 16 16 16 16 16 16

30 16 16 16 16 16 16 16 16 16 16 16 16

32 16 16 16 16 16 16 16 16 16 16 16 15

34 16 16 15 16 16 16 16 16 16 16 15 14

36 16 16 15 16 16 16 16 16 16 15 14 13

38 16 16 14 16 16 15 16 16 15 14 13 12

40 16 15 13 16 15 14 16 15 14 13 12 12

Other plate dimensions on agreement

2,101 2,201 2,301 2,401 2,501 2,601 2,701 2,801 2,901 width [mm]thickness [mm]2,200 2,300 2,400 2,500 2,600 2,700 2,800 2,900 3,000

14 14 14 14 14 8

16 16 16 14 14 9

16 16 16 16 16 16 16 10

16 16 16 16 16 16 16 11

16 16 16 16 16 16 16 12

16 16 16 16 16 16 16 13

16 16 16 16 16 16 16 16 16 14

16 16 16 16 16 16 16 16 16 15

16 16 16 16 16 16 16 16 16 16

16 16 16 16 16 16 16 16 16 17

16 16 16 16 16 16 16 16 16 18

16 16 16 16 16 16 16 16 16 19

16 16 16 16 16 16 16 16 16 20

16 16 16 16 16 16 16 16 16 21

16 16 16 16 16 16 16 16 15 22

16 16 16 16 16 16 16 15 15 23

16 16 16 16 16 16 15 14 14 24

16 16 16 16 15 15 14 14 13 25

16 16 16 15 15 14 14 13 13 26

16 16 15 14 14 13 13 12 12 28

15 15 14 13 13 12 12 11 11 30

14 14 13 12 12 11 11 11 10 32

13 13 12 12 11 11 10 10 9 34

13 12 11 11 10 10 10 9 9 36

12 11 11 10 10 9 9 9 8 38

11 11 10 10 9 9 9 8 8 40

EVRAZ VÍTKOVICE STEEL, a. s.

Headquarters: Štramberská 2871/47, 709 00 Ostrava-Hulváky, Czech Republic

Postal address: EVRAZ VÍTKOVICE STEEL, a. s., 706 02 Ostrava-Vítkovice, Czech Republic

Phone: +420 595 952 435, Fax: +420 595 952 144

E-mail: [email protected]

Valid from: 6/2007

Download - Catalogue of Plates New[1]

Top Related