Download - Camera_sanyo VPC-S60EX/VPC-S60
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
1/140
VPC-S60EX
VPC-S60
INSTRUCTION MANUAL
Digital Camera
Please read these instructions carefully before using the camera.Make sure to read and understand the separate booklet SAFETY MANUAL.Keep this manual in a safe place for later reference.
Important noteThis manual explains how to safely operate the VPC-S60EX and VPC-S60.Any information regarding only one of these products will be labeled as such.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
2/140
i English
WarningTO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
FOR AMERICAN USERSThe following advisory is included in accordance with the laws of the State ofCalifornia (USA):WARNING:This product contains chemicals, including lead, known to the State ofCalifornia to cause cancer, birth defects or other reproductive harm. Washhands after handling.
i This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will notoccur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correctthe interference by one or more of the following measures:h Reorient or relocate the receiving antenna.h
Increase the separation between the equipment and receiver.h Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.
h Consult the dealer or an experienced radio/TV technician for help.iChanges or modifications not expressly approved by the party responsible
for compliance could void the users authority to operate the equipment.
Model number: VPC-S60
Trade Name: SANYOResponsible party: SANYO FISHER COMPANYAddress: 21605 Plummer Street, Chatsworth, California 91311Telephone No.: (818) 998-7322This device complies with Part 15 of the FCC Rules. Operation is subjectto the following two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
Declaration of Conformity
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
3/140
English ii
FOR CANADIAN USERSi This Class B digital apparatus complies with Canadian ICES-003.
FOR EU USERSNote:iThis symbol mark and recycle system apply only to EU
countries and do not apply to countries in other areas ofthe world.
Your SANYO product is designed and manufactured withhigh quality materials and components which can berecycled and reused.This symbol means that electrical and electronic
equipment, at their end-of-life, should be disposed ofseparately from your household waste.Please dispose of this equipment at your local communitywaste collection/recycling centre.In the European Union there are separate collectionsystems for used electrical and electronic products.Please help us to conserve the environment we live in!
Symbols used in this manualHINT Points giving some extended instructions or special points to pay
attention to.
CAUTION Points that require special attention.(page xx) Refer to the page indicated for detailed information.
You may find the answers to questions or problems concerning cameraoperation in the sections COMMONLY ASKED QUESTIONS (page 111)and TROUBLESHOOTING (page 117).
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
4/140
iii English
GETTING UP AND RUNNING
Install the battery1 Open the battery/card cover, and insert the batteries.
h The battery/card cover is located on the bottom of the camera.
2 Press the ON/OFF button to turn the camera on.h The Shooting Screen appears.
Battery/card cover
Batteries
180
ON/OFF button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
5/140
English iv
Shooting
Single shot (stillimage) photography
1 Press the [m] button.h The screen to set the
shooting mode and selftimer appears.
2 Press the [m] button to select
the single shot mode, andpress the SET button.h An icon in the upper left
area of the monitor indicatesthe active shooting modesetting.
c: Single shot modeP: Sequential shots modeX: Video clip recording mode
3 Press the shutter button.h The image is captured.
Video clip recording
1 Press the [m] button to select
the video clip recordingmode.
2 Press the shutter button.h Recording begins.h To stop recording, press the
shutter button again.
180
Shutter button
SET button
[m] button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
6/140
v English
Playback
Still image playback
1 Press the playback button [=].h The display switches to the
Playback Screen.h To view other images, press the
[l] or [m] button.h If the playback button [=] is
pressed, the display returns tothe Shooting Screen.
Video clip playback
1 Press the playback button [=].h The display switches to the
Playback Screen.h Press the [l] or [m] button to
display the video clip you wish toplay back.
h Video clips are indicated by avideo clip pattern along the topand bottom of the screen.
2 Press the SET button.h Playback of the selected video
clip begins.
h If the playback button [=] ispressed again, the displaychanges to the Shooting Screen.
When you are finished taking pictures...Press the ON/OFF button to turn the camera off.
Playback button [=]
SET button
Video clip pattern
[l] or [m] button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
7/140
1 English
QUICK SEARCH BY OPERATIONYour camera has an abundance of convenient features and functions. Fromcreating precisely the photo you want, to viewing images using various
techniques, you can locate the exact operation for your purposes in thefollowing table.
Basic operationConvenientfunctions Additional functions
Shooting/recordin
g
Getting startedshooting Recording a video clip
on page 40 Shooting single shots
on page 31 SHOOTING
SEQUENTIAL SHOTSon page 39
Log the date andtime of your photos DATE AND TIME
SETTING on page 19
Zoom in on the
subject USING THE ZOOM
on page 47
Close-upphotography FOCUS RANGE
(macro mode) onpage 52
For more accuratefocus FOCUS RANGE
(manual focus) onpage 52
Set the focus to anarrow range FOCUS AREA
SETTING on page 61
Check the focusstatus Zoom jump playback
on page 36
Optimize the photo quality RESOLUTION/VIDEO CLIP SETTING on page 58
Capture fast-moving subjects USING THE SCENE FUNCTION (sports mode) on page 44
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
8/140
English 2
Shooting/recording
Shoot in dark conditions EXPOSURE CORRECTION on page 65 FLASH SETTING on page 48
USING THE SCENE FUNCTION (night view mode) on page 44Increase the cameras sensitivityISO SENSITIVITY on page 62
Photographing people USING THE SCENE FUNCTION (cosmetic mode/portrait mode/night view
mode) on page 44 FLASH SETTING (red-eye reduction) on page 48
Photographing landscapes USING THE SCENE FUNCTION (landscape mode) on page 44
Take a self-photo SELF-TIMER on page 50
Make images lighteror darker EXPOSURE
CORRECTION onpage 65
Adjust the camerassensitivity ISO SENSITIVITY on
page 62
Change the color ofthe images
USING THE SCENEFUNCTION(monochrome/sepia)on page 44
Make white appearnatural
WHITE BALANCE onpage 63
Basic operation Convenientfunctions
Additional functions
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
9/140
3 English
Playback
Getting startedviewing images Playing back the video
clip on page 41
Viewing still imageson page 33
Search for imagedata 9-image display
playback on page 34
Magnify an image Magnifying (zooming
in) the image onpage 35
Check the focusstatus Zoom jump playback
on page 36
Change the angle ofview ROTATE IMAGE on
page 70
Slideshow playback SLIDESHOW PLAYBACK on page 80
Adjust the monitor brightness Adjust the monitor brightness on page 29
Datamanaging/processing Search for image data
9-image display playback on page 34
Delete files Erasing files on
page 37
Protect images from accidental erasure IMAGE PROTECT on page 68
Format a card
INITIALIZING THE CARD MEMORY ANDINTERNAL MEMORY on page 95
Specify the number of prints and date imprint PRINT SETTINGS on page 74
View the settings that were in effect when the image/audio datawas recorded DISPLAYING IMAGE PROPERTIES (INFORMATION SCREEN) on page 81
Basic operation Convenientfunctions
Additional functions
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
10/140
English 4
CONTENTSQUICK SEARCH BY OPERATION ........................................................1CONTENTS ............................................................................................4
CHECKING THE INCLUDED ACCESSORIES ......................................7GETTING THE MOST OUT OF YOUR CAMERA ..................................9SYSTEM MAP ......................................................................................11
SETUPPARTS NAMES ....................................................................................12INSTALLING THE BATTERIES AND CARD ........................................14TURNING THE CAMERA ON AND OFF ..............................................17DATE AND TIME SETTING .................................................................19
BASIC OPERATIONBEFORE TAKING PICTURES .............................................................22CAPTURING AND PLAYING BACK STILL IMAGES ...........................31SHOOTING SEQUENTIAL SHOTS .....................................................39VIDEO CLIP RECORDING AND PLAYBACK ......................................40USING THE SCENE FUNCTION .........................................................44USING THE ZOOM ..............................................................................47FLASH SETTING ..................................................................................48
SELF-TIMER ........................................................................................50FOCUS RANGE ...................................................................................52
SHOOTINGACCESSING THE RECORDING MENU ..............................................54TOUCH SENSOR (TOUCH FOCUS) SETTING ..................................57RESOLUTION/VIDEO CLIP SETTING .................................................58FOCUS AREA SETTING ......................................................................61ISO SENSITIVITY .................................................................................62
WHITE BALANCE ................................................................................63EXPOSURE CORRECTION .................................................................65
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
11/140
5 English
CONTENTS
PLAYBACKDISPLAYING THE PLAYBACK MENU ................................................ 66
IMAGE PROTECT ............................................................................... 68ROTATE IMAGE .................................................................................. 70CHANGING IMAGE SIZE (RESIZE) .................................................... 71COPY DATA ........................................................................................ 72PRINT SETTINGS ............................................................................... 74SLIDESHOW PLAYBACK ................................................................... 80DISPLAYING IMAGE PROPERTIES (INFORMATION SCREEN) ...... 81
OPTION
DISPLAYING THE OPTION MENU ..................................................... 82SOUNDS .............................................................................................. 85POST-VIEW SETTING ........................................................................ 87SCREEN LANGUAGE ......................................................................... 88TV SYSTEM SETTING ........................................................................ 89AUTO POWER OFF FUNCTION ......................................................... 90FILE No. RESET FUNCTION .............................................................. 92INITIALIZING THE CARD MEMORY AND INTERNAL MEMORY ...... 95RESETTING THE CAMERA SETTINGS ............................................. 97
CHECKING THE REMAINING INTERNAL MEMORY ANDCARD MEMORY ............................................................................. 98CHECKING THE REMAINING BATTERY CHARGE ......................... 100
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
12/140
English 6
OTHER DEVICES AND CONNECTIONSCONNECTING TO A TV .....................................................................102DIRECT PRINTING ............................................................................103
APPENDICESCOMMONLY ASKED QUESTIONS ...................................................111TROUBLESHOOTING ........................................................................117SPECIFICATIONS ..............................................................................123HINTS FOR TAKING PICTURES .......................................................130
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
13/140
7 English
CHECKING THE INCLUDED ACCESSORIES
Handstrap: 1 SANYO Software Pack
(CD-ROM): 1
AA alkaline batteries: 2(batteries made exclusively to
be used as includedaccessories)
Dedicated AV interfacecable: 1
Dedicated USB interface cable: 1 SAFETY MANUAL
(safety precautions booklet)Please read this bookletcarefully before using thedigital camera.
Quick Guide
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
14/140
English 8
Attaching the handstrap
Media cards that can be used with this cameraThe types of card that can be inserted into and used with this camera are:i SD Memory CardiMulti Media Card
What card means in this manuali In this manual, SD Memory Cards and Multi Media Cards that can be used
in this digital camera are referred to as card.i The cards in the illustrations in this manual are SD Memory Cards, but allinstallation, removal, and formatting procedures are the same for both SDMemory Cards and Multi Media Cards.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
15/140
9 English
GETTING THE MOST OUT OF YOUR CAMERAIts loaded with lots of functions that are possible only in a digital camera,including a super-quick focus, an easy-to-understand guidance display on a
large screen, a more extensive scene function, and more.
Youll never miss a photo opportunity, thanks tothe quick focus: Touch focus (see page 57)Just touch the shutter button lightly, and the touch sensor automaticallyfocuses the image (touch focus).
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
16/140
English 10
Abundant scene functionsYou can select from a variety of preset settings (aperture, shutter speed, etc.)for specific shooting conditions.
Speedy mode-switchingSwitch the shooting mode from still images to video clips to sequential shotswith a single button operation.
USE AUTO SETTINGSSE UTO SETTINGS
AUTOUTO
VIDEO CLIP
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
17/140
11 English
SYSTEM MAPThe included accessories can be used to connect your camera to a computer,printer or TV. By connecting the camera to your computer, you can, for exam-
ple, copy your photos to the computers hard disk. You can connect it to aprinter for direct printing of your photos. Or take the card to a photo shop tohave your photos printed there.
DedicatedUSB interfacecable
Dedicated AVinterface cable
Computer
Printer
TV
DC adaptor(sold separately)
Separately sold orcommercially available
SD Memory Card/Multi Media Card
Internet
AC adaptor(optional)
iCard readeriDPOF-
compatibleprinter
iPhoto shop
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
18/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
19/140
13 English
PARTS NAMES
Rear
Bottom
MENU button
Zoom switch [W]/[T]
Monitor
SET button
Speaker
Tripod stand hole
Playback button [=]
Battery/card cover
[n] button
[o] button
[l] button
[m
] button
Strap holder
Illumination sensor
Detects the ambientbrightness andautomaticallyadjusts thebrightness of themonitor accordingly.
SCENE button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
20/140
English 14
INSTALLING THE BATTERIES ANDCARDYour camera has an internal memory, which means that you can take photoseven when no card is installed. By using a card, however, you will be able totake many more photos.The card can be used after it has been formatted with the camera (page 95).
1 Open the battery/card cover.h While gently pressing the
battery/card cover, slide it open.
2 Insert the batteries.h Make sure that the batteries
polarities (Mand N) arecorrect.
Battery/card cover
Batteries
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
21/140
15 English
INSTALLING THE BATTERIES AND CARD
3 Insert the card.h Firmly insert the card until it
clicks into place.
4 Close the battery/card cover.
When removing the card...h To remove the card, press it
down, and then release. Thecard will protrude slightly, andyou can then pull it out.
Keep your finger on the card until itis completely inserted or released.i If you remove your finger too soon,
the card may spring out andbecome lost or hit someone in theeye.
Card
[o
] mark
2 Press andrelease
1 Open
3 Pull out
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
22/140
English 16
CAUTIONBe careful when removing the card.iDo not attempt to forcibly remove the card.iNever remove the card when the camera is connected to a computer or
printer, or when the self-timer indicator is flashing quickly. In doing so, you
risk losing the data stored in the card.Manganese batteries cannot be used.iNot only do manganese batteries have a short battery life, but there is the
danger of their overheating and causing damage to the digital camera.Other batteriesi If you wish to use batteries other than the alkaline batteries (LR6), we
recommend the following.h AA-size nickel metal hydride (NiMH) rechargeable batteries (SANYO
HR-3UTG) 2
h AA-size Ni-Cd batteries (SANYO N-3UV) 2When installing the batteries, make sure that they are oriented correctly.
Do not open the battery/card cover when the camera is turned on.i If the battery/card cover is opened while the power is on, important data
may be lost. Sanyo Electric shall not be held responsible for any lossesthat result from failure to comply with this warning.
HINTShooting without a card installediWhen a card is installed, images are recorded to and played back from the
card. When no card is installed, images are recorded to and played backfrom the cameras internal memory. When the camera is turned on with nocard installed, the internal memory icon is shown on the monitor to letyou know that the images you capture will be saved to the camerasinternal memory.
About the internal backup batteryi This cameras internal battery serves to maintain the date and time
settings, as well as the shooting settings. The backup battery will be fully
charged when the batteries are kept in the camera continuously for about 2days. In the fully charged state, the backup battery will maintain thecamera settings for about 7 days.
When not using the camera for a long time, remove the batteries.i A small amount of power is still used even if the camera is turned off, and it
is therefore recommended that the batteries be removed from the cameraif it is not going to be used for a long time. Note that when the batteries areremoved for a long period, the time and date settings may be cleared.Before using your camera again, be sure to confirm that the camerasettings are correct.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
23/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
24/140
English 18
About the auto power off functionIn order to preserve battery power when, for example, the camera hasaccidentally been left on, the camera is furnished with an auto power offfunction by which the camera automatically turns off after a certain period of
inactivity (about 1 minute during shooting or about 3 minutes during playback[factory default settings]).i If the auto power save function has operated to turn the camera off, press
the ON/OFF button to turn it back on.i You can change the setting for the time elapsed before the camera
automatically turns off (page 90).iWhen the camera is connected to a computer or printer using the
dedicated USB connection cable, the auto power save function is disabled,and the camera turns off after about 12 hours.
HINTIf theKicon appears...iWhen a picture is taken, the date and time it was captured is recorded with
it. When the date and time cannot be recorded with the image because thedate and time have not yet been set (page 19), theKicon appears. Tohave the date and time recorded with images, please make this settingbefore capturing images.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
25/140
19 English
DATE AND TIME SETTINGThe camera will record the date and time an image is captured so that youcan display them during playback. Therefore, before capturing images, make
sure the correct date and time are set.
Example: To set the clock to 7:30 p.m. on December 24, 2006
1 Press the ON/OFF button to turn thecamera on, and press the MENUbutton.h The Recording Menu appears
(page 54).
2 Press the [o] button to select the3tab.h The Option Menu appears.
3 Press the [m] button to selectCLOCK SET, and press the SETbutton or the [m] button.h The Clock Set Screen appears.h The current date and time settings
are shown.h Follow the procedures below to
enable or disable the date displayduring playback, to set the displayformat for the date, and to set thedate and time.
h To return to the Option Menu, pressthe MENU button.
RECORDING MENU
TOUCH SENSOR
RESOLUTION
FOCUS METHOD
ISO
WHITE BALANCE
EXPOSURE
CLOCK SETSOUND
POST VIEW
LCD BRIGHTNESSLANGUAGE
TV SYSTEM
OPTION MENU(1/2)
2 SEC
NTSC
CLOCK SETLOCK SET
OKK
2006/03/01
Y / M / D
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
26/140
English 20
4 Set the date and time.1 Press the [m] button to select the
year indication.2 Press the [n] or [o] button to
change the year indication.h Repeat these steps to select themonth indication and dayindication, and set the date toDecember 24, 2006.
3 Press the SET button or the [m]button to select the time indication.
4 Press the [n] or [o] button tochange the time setting.
5 Press the [m] button to select the
Y/M/D indication.6 Press the [n] or [o] button to
change the displayed date order.
h Press the [n] button to change the displayed date order as follows:
h Press the [o] button to change it in the reverse order.
CLOCK SETLOCK SET
Y / M / D
OKK
CLOCK SETLOCK SET
Y / M / D
OKK
CLOCK SETLOCK SET
Y / M / D
OKK
year/month/daymonth/day/year day/month/year
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
27/140
21 English
DATE AND TIME SETTING
5 Press the SET button.h The date and time setting is completed, and you are returned to the
Option Menu.h The Option Menu is canceled when the MENU button is pressed.
HINTiUnder normal conditions, while the batteries are being replaced, an
internal battery will maintain the date and time settings. However, there is asmall chance the settings may be lost. (The backup will last for about 7days.) It is recommended to check that the date and time settings are still
correct after replacing the batteries and before shooting or recording of anytype (follow steps 1to 4).
To correct the date and time settingsi In step 4, select the indication that you want to change, and follow the
procedure to change the indication.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
28/140
English 22
BASIC OPERATION
BEFORE TAKING PICTURES
How to hold the cameraHold the camera securely, keeping your elbows close to your body andmaking sure the camera is stable.
Make sure that the lens and flash are not blocked by your fingers or thehandstrap.
HINTi Images captured in the still image shooting mode can be rotated when
they are played back (page 70).iWhen the optical zoom is used or when the autofocus is operating, the
image may appear to waver, but this is not a malfunction.
A finger is blocking the lens or flash.
Correct hold Incorrect hold
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
29/140
23 English
BEFORE TAKING PICTURES
About the touch sensor (touch focus)
With the touch sensor, the image is focused simply by a light finger-touch onthe shutter button (focus lock). With the subject in focus, just gently press theshutter button to take the picture for a perfectly focused image.At the same time, the touch sensor is temporarily deactivated whenever theRecording Menu (page 54) is displayed, thereby facilitating operation of thesescreens.Furthermore, you can also deactivate the touch sensor so that the autofocusoperates only when you press the shutter button halfway (page 57).
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
30/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
31/140
25 English
BEFORE TAKING PICTURES
The following examples are some of the situations where the autofocusfunction may work, but not as desired.When both near and far objects are
presentUse the focus-lock function to lock thefocus on an object at the same distance asthe desired subject, then reposition thecamera to compose the picture.
Fast-moving subjectsUse the focus-lock function to lock thefocus on an object at the same distance asthe desired subject, then reposition thecamera to compose the picture.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
32/140
English 26
Switching between the shooting mode andplayback mode
Switch between the shooting mode and the playback mode.
1 Press the ON/OFF button to turnthe camera on.
2 Press the playback button [=].h Each time the playback button is
pressed, the camera switchesbetween the shooting mode and
the playback mode.
HINTTo turn the camera on in the playbackmodei Press the playback button [=] for at least 1 second, and the camera will
turn on in the playback mode.
180
100-0001
ON/OFF button
Playback button[=]
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
33/140
27 English
BEFORE TAKING PICTURES
How to switch the shooting mode
Your camera can capture single still photos (single shot shooting mode),record video clips (video clip recording mode), and also capture a series ofstill photos (sequential shots shooting mode).
1 Press the ON/OFF button toturn the camera on.
2 Press the [m] button.
h The screen to set theshooting mode and the selftimer appears.
3 Press the [m] button to selectthe shooting mode.
4 Press the SET button.h The selected shooting mode
is not set.h An icon in the upper left area
of the monitor indicates theactive shooting mode setting.
180
ON/OFF button
[m] button
SET button
c:Single shot mode
X:Video clip recording mode
P:Sequential shots mode
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
34/140
English 28
Switching the display modeIn the shooting mode, you can select the either the settings display modewhich allows you to confirm the shooting settings on the monitor while youshoot, or the normal display mode in which the setting indications are turned
off, providing a full view of the subject.
1 Press the ON/OFF button to turnthe camera on.
2 Press the SET button.h Each time the SET button is
pressed, the camera switches
between the settings displaymode and the normal displaymode.
180
ON/OFF button
SET button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
35/140
29 English
BEFORE TAKING PICTURES
Adjust the monitor brightness
The brightness of the monitor is adjustable. Adjust the brightness to theoptimum readability in the ambient light.
1 Press the ON/OFF button toturn the camera on.
2 Press the MENU button for atleast 1 second.
h The Monitor BrightnessScreen appears.
3 Press the [n] and [o] buttonsto adjust the brightness.h When set to AUTO, the
illumination sensor (page 13)detects the ambientbrightness and automaticallyadjusts the brightness of themonitor accordingly.
4 Press the SET button.h The monitor brightness is
set, and the MonitorBrightness Screen iscanceled.
LCD BRIGHTNESS
ON/OFF button
MENU button
[o] button
[n] button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
36/140
English 30
Hints for taking picturesMuting the camera soundsi The operation sounds that are generated, for example, when the shutter
button, MENU button or SET button is pressed, can be muted (page 85).
Where is the image data saved?i All the image and sound data is recorded in the cameras internal memory
or on the card installed in the camera.iWhen a card is installed in the camera, the data is recorded on the card. If
no card is installed, the data is recorded in the cameras internal memory.
Taking pictures in backlight conditions...iWhen taking pictures with the light coming from behind the subject, due to
the characteristics of the CCD, light lines or ghost patterns (flarephenomenon) may appear in the captured image. In this situation, it isrecommended that you avoid taking pictures with the subject lit frombehind.
Switching the guidance display ON/OFFi Press the [l] button. Each time the [l] button is pressed, the guidance
display switches between ON and OFF.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
37/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
38/140
English 32
3 Gently press the shutter button.h Press the shutter button gently, taking care not to
move the camera.h The image that was captured appears on the
monitor as long as the shutter button is keptpressed (post view).
4 Release your finger from the shutter button.h The captured image is recorded.
HINTWhat is the camera focusing on?i A target mark&on the monitor shows
the area the camera is focusing on.
i The camera automatically determines thecorrect focus by measuring from 9different focus points within the shootingarea. If the target mark is at a positionthat is different from the point you wish tofocus on, you can refocus, for example,by changing the shooting angle.
i The large target mark appears whenthe camera focuses on a wide area inthe center of the screen.
About the focus indicatori A green focus indicator appears when
the subject is successfully focused, or ared focus indicator when the camerawas not able to focus the subject.
The shutter speed and aperture are displayediWhen the camera focuses and the target
mark appears, at the same time, theshutter speed and aperture settings arealso displayed. You can use them as a
reference when shooting.If the motion alert icon appears...iDuring still image shooting, if the shutter speed is slow and the possibility
that the image may be blurred due to camera shake becomes high, themotion alert icon may appear on the monitor. In this case, use a tripod tostabilize the camera when shooting, or set the flash operation mode toautomatic (page 48).
iWhen shooting with the scene function set to the fireworks^mode, themotion alert icon always appears, but this is normal.
F2.8
1/30
F2.8
1/15
Shutter speed
Aperture
Target mark
Motion alert icon
Focus indicator
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
39/140
33 English
CAPTURING AND PLAYING BACK STILL IMAGES
Viewing still images
The steps for viewing both single shots and sequential shots are the same.
5 Press the playback button [=].h If the playback button [=]
was pressed to turn thecamera on, however, pressthe playback button [=] forat least 1 second.
h The image most recently
captured appears on themonitor.
6 View other images.h Press the [l] or [m] button to
display the previous or nextimage.To display the previous
image:Press [l].
To display the next image:Press [m].
h To return to Shooting Screen,press the playback button[=].
h When the playback button[=] or ON/OFF button ispressed, the camera turns off.
When you are finished viewing images...iPress the ON/OFF button to turn the camera off.
HINT
For still images with voice memo (page 46)...iWhen the shutter button is pressed, the voice memo is played back.
100-0001 100 0001
2006.12.24006.12.24
100-0001
2006.12.24
Playback button [=]
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
40/140
English 34
9-image display playback
1 Press the playback button[=].
2 Press [W] ([P]) on thezoom switch.h The 9-image display
appears.
3 Select the image to play
back.h Press the arrow buttons tomove the orange frame tothe desired image, andpress the SET button.Instead of pressing theSET button, you can press[T] ([]]) on the zoomswitch to show the imagefull screen.
100
0001 0002 0003
0004 0005 0006
0007 0008 0009
SET button
Zoom switch
Orange frame
Still image
Image number
Videoclip
Folder number
Arrow buttons
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
41/140
35 English
CAPTURING AND PLAYING BACK STILL IMAGES
Magnifying (zooming in) the image
1 Display the image that you want to magnify.
2 Press [T] ([]]) on the zoomswitch.h Magnification is enabled.h The image is magnified, and the
central portion of image is
displayed.h Press the arrow buttons to viewdifferent parts of the magnifiedimage.To magnify:Magnification increases witheach press of [T] ([]]) on thezoom switch.To return to normal size:Magnification decreases witheach press of [W] ([P]) on thezoom switch.
h Press the SET button to return tothe normal (100%) view.
HINTThe magnified portion of the image can be saved as a separate image.iPress the shutter button. The magnified portion is saved as a new still
image.
MOVE
ZOOM I/O
PRESS SHUTTER TO SAVE
100%
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
42/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
43/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
44/140
English 38
1 Use the [l] and [m] buttons to display the file you wish to delete.2 Press the [n] or [o] button to select DELETE SINGLE.3 Press the SET button.h The currently displayed file is deleted.h
To delete other files, repeat steps 1to3.
CAUTIONAbout protected imagesi Files that are protected from accidental erase cannot be erased. To erase
protected files, set the protect setting for the file to off (page 68), and thenfollow the file delete procedure.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
45/140
39 English
SHOOTING SEQUENTIAL SHOTSWhen the shutter button is pressed, still images are captured in succession.
1 Set the camera to the sequentialshots mode (page 27).h If the resolution is set tok, the
setting changes automatically to{.
2 Press the shutter button to startshooting.
h Sequential shots shooting begins.
* The maximum number ofsequential shots will differdepending on the subject.
h Note that if the shutter button isreleased during shooting, shootingstops immediately.
HINTLimitations of sequential shots settingsi It is not possible to set the resolution toE.i The following scene functions cannot be set.\]^_anda.
i Flash photography is not possible.
Resolution Max. no. of shots
D Approx. 4 shots
z Approx. 6 shots
t Approx. 12 shots
[ Approx. 79 shots
Sequential shotsshooting icon
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
46/140
English 40
VIDEO CLIP RECORDING AND PLAYBACK
Recording a video clip
1 Set the camera to the videoclip recording mode(page 27).
2 Press the shutter button.h Video clip recording
begins.
During recording,the recording time is shownon the monitor.
h It is not necessary tocontinue pressing theshutter button whileshooting.
3 End the recording.h Press the shutter button
again to stop recording andsave the video clip. 00:45:000:45:0000:45:00
Shutter button
Video clip shooting icon
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
47/140
41 English
VIDEO CLIP RECORDING AND PLAYBACK
Playing back the video clip
4 Press the playback button[=].h If the playback button [=]
was pressed to turn thecamera on, however, pressthe playback button [=] forat least 1 second.
h The video clip just recorded
appears on the monitor.h Video clips are indicated by
a video clip pattern alongthe top and bottom of thescreen.
5 Press the SET button.h Video clip playback begins.
h To stop playback, press the[o] button.
100-0008 100 0008
2006.12.24006.12.24
100-0008
2006.12.24
Playback button [=]
Video clip pattern
[o] button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
48/140
English 42
Outline of playback operation
When you are finished viewing video clips...i Press the ON/OFF button to turn the camera off.
CAUTIONIf no audio is heard...The audio is not played back when the video clip is played back in the frame-
by-frame, fast playback or reverse playback mode.
To do this... Do this
Stop playback During playback, press the [o] button
PauseDuring playback, press the SET button.
During accelerated playback, press the [n] button.To extract a still image While playback is paused, press the shutter button.
To play backone imageat a time(single-
frame step)
During forwardplayback
While playback is paused, press the [m]button.
During reverseplayback
While playback is paused, press the [l]button.
Slowplayback
During forwardplayback
While playback is paused, press and hold the[m] button.
During reverseplayback
While playback is paused, press and hold the[l] button.
Toaccelerate
playback
Forwardplayback
During forward playback, press the [m] button.* The playback speed changes each time the
[m] button is pressed, as follows:Normal playback 2x 5x 10x 15xPress the [l] button to resume normalplayback speed.
Reverseplayback
During forward playback, press the [l] button.* The playback speed changes each time the[l] button is pressed, as follows:
15x 10x 5xPress the [m] button to resume normalplayback speed.
Return to normal playback speed Press the SET button.
Adjusting the volume
Louder:During playback, press [T] on thezoom switch.
Softer:During playback, press [W] on thezoom switch.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
49/140
43 English
VIDEO CLIP RECORDING AND PLAYBACK
CAUTIONThe data for a video clip is very large.i Therefore, be aware that if the video clip is uploaded to a computer to be
played back, the computer may not be able to play back the video fastenough, making it appear jerky. (The video will always be displayedproperly on the monitor.)
If video clip recording stops even when there is card memoryremainingiDepending on the card you are using, recording may stop even if there is
remaining memory in the card.i For video clip recording, it is recommended that a high-speed memory
card be used.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
50/140
English 44
USING THE SCENE FUNCTIONYou can select from a variety of preset settings (aperture, shutter speed, etc.)for specific shooting conditions.
1 Set the camera to the shootingmode (page 26), and press theSCENE button.h The screen to select the settings
suitable for the scene (shootingconditions) appears.
2 Use the arrow buttons to select thedesired setting.
Scene setting Features
Shooting mode setting
c P X
XAuto
The camera makes theoptimum settings.
m m m
YSports
Capture a split-second imageof a fast-moving subject.
m m m
ZPortrait
Enhance the three-dimensional feel of thesubject by blurring thebackground.
m m m
[Flowers
Capture the vivid colors offlowers.
m m m
\Landscape
For beautiful shots of distantscenery.
m n m
]Night view
Photograph the subject whilekeeping the backgroundnight scenery.
m n m
USE AUTO SETTINGSSE AUTO SETTINGS
AUTOUTO
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
51/140
45 English
USING THE SCENE FUNCTION
m: Available n: Not available
3 Press the SET button.h This completes the scene select
setting.h The display returns to the Shooting
Screen.h The scene function setting is shown
on the monitor.
Scene setting FeaturesShooting mode setting
c P X
^Fireworks
For capturing fireworks atnight.
m n m
_Lamp
Photograph in low-lightconditions
m n m
aStill image with
sound
Shoot a still image and add avoice memo.
m n n
7Cosmetic Skin tones are enhanced inclose-up shots. m m m
8Monochrome
Create black-and-whitephotos.
m m m
9Sepia
Create sepia-tone photos. m m m
?Sharpness
Accentuates the outlines inthe image.
m m m
>Contrast
Accentuates the light anddark areas in the image.
m m m
@Vivid
Accentuates the colors in theimage.
m m m
180
Scene function setting
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
52/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
53/140
47 English
USING THE ZOOMYour camera has two zoom functions: optical zoom and digital zoom.
1 Set the camera to the shootingmode (page 26), and point thecamera lens at the subject.
2 Press the zoom switch tocompose the desired image.[T]: Zoom in on the subject.[W]: Zoom out.
h When the zoom switch ispressed, the zoom bar appearson the monitor.
h When the optical zoom factor isat maximum, zooming stopstemporarily. When [T] on thezoom switch is pressed again,the mode changes to the digitalzoom mode and zooming
continues.
3 Take the picture.
HINTCant access the digital zoom?iWhen the resolution is set tok, the digital zoom is not available in the
single-shot mode.Cant access the optical zoom?iDuring video clip recording, only the digital zoom is available, and the
optical zoom cannot be used.
Zoom switch
Zoom bar
Monitor
PointerWhen both opticaland digital zoom areenabled
Digital zoom (yellow)
Optical zoom
When optical zoomonly is enabled
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
54/140
English 48
FLASH SETTINGThe flash is used not only for taking pictures where there is insufficient light,but also when the subject is in shade or in backlight conditions. Your cameras
flash has four modes of operation (automatic flash mode, forced flash mode,flash off mode and red-eye reduction mode). Select the flash mode that isappropriate for the surrounding conditions. The flash can be enabled onlywhen taking single-shot still images.
1 Set the camera to the single-shotshooting mode (page 27), andpress the [n] ([?]) button.h The flash setting changes.
h The flash setting appears on themonitor.
h The flash setting can also bechanged from the RecordingMenu (page 55).
No flash indication:The camera will detect thesubject brightness and use theflash only when required. In a
backlight situation, if only thecenter of the image is very dark,the flash will operate tocompensate (auto flash).
m: The flash will operate with everyimage captured regardless of theconditions. Use this settingunder backlight conditions, whenthe subject is in shade, under
fluorescent lighting conditions,etc. (forced flash).
l: The flash will not operate even in dark situations. Use this settingwhen capturing an image in a location where flash photography isprohibited, or when shooting a night landscape scene (flash off).
J: The digital camera will detect the subject brightness and use theflash only when required. At this time the flash will operate in amanner that reduces the red reflection (red-eye) in the subjectseyes (red-eye reduction).
FLASHAUTO
[n] ([?]) button
Flash mode icon
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
55/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
56/140
English 50
SELF-TIMERSelf-timer photography is available in the single-shot shooting mode.
1 Set the camera to the shootingmode (page 26), and press the [m]button.
2 Use the [n] and [o] buttons to selectthe self-timer setting.
3 Press the SET button.h This completes the self-timer setting.
y: The image is captured about2 seconds after the shutter buttonis pressed.
x: The image is captured about10 seconds after the shutter buttonis pressed.
PHOTOGRAPH 1 IMAGE
Self-timer menu
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
57/140
51 English
SELF-TIMER
HINTTo pause or cancel the self-timer function...i If the shutter button is pressed again before the shutter is released, the
self-timer countdown temporarily stops. Press the shutter button one moretime to restart the self-timer.
i To cancel self-timer photography, set the self-timer setting to off c.iAfter the self-timer picture is snapped, the self-timer is automatically reset
to off.
When xis selected...iWhen the shutter button is pressed,
the self-timer indicator flashes forapproximately 10 seconds, afterwhich shooting begins.
iAbout 3 seconds before shooting,the self-timer indicator flashesfaster.
Self-timer indicator
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
58/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
59/140
53 English
FOCUS RANGE
How to use the manual focus
1 Set the focus range to manual -(page 52).
2 Press the SET button.h The focus distance adjustment bar
appears.
3 Press the [l] or [m] button to adjustthe focus distance, and press theSET button.h The focus distance is set, and you
are returned to the ShootingScreen.
HINTAbout the focus rangei The focus distance indication shows the distance between the lens surface
and the subject.i In some cases there may be a slight variance between the distance
(numerical figure) you set in the manual focus mode and the actualdistance. Use the monitor to confirm the focus and compose the photo.
About zoom movement when using the manual focusi If the focus distance is set to 30 cm (11.81 in.) or less, the zoom changes
to the largest setting that is suitable for that focus distance.iWhen the focus distance is set to 30 cm (11.81 in.) or less, the zoom will
function only within the range at which the image is focused.
FOCUSMANUAL
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
60/140
English 54
SHOOTING
ACCESSING THE RECORDING MENUDetailed shooting settings are accessed from the Recording Menu.
1 Set the camera to a shootingmode (page 27).
2 Press the MENU button.h The Recording Menu
corresponding to the shootingmode set in step 1appears.
h The Recording Menu can be
canceled by pressing the MENUbutton.
RECORDING MENU
TOUCH SENSOR
RESOLUTIONFOCUS METHOD
ISO
WHITE BALANCE
EXPOSURE
MENU button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
61/140
55 English
ACCESSING THE RECORDING MENU
Overview of the Recording Menu
RECORDING MENU
TOUCH SENSOR
RESOLUTIONFOCUS METHOD
ISO
WHITE BALANCE
EXPOSURE
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
62/140
English 56
1 Touch sensor menu (page 57)
2 Resolution menu/video clipmode menu (page 58)
3 Focus mode menu (page 61)
4 ISO sensitivity menu
(page 62)
5 White balance menu (page 63)
6 Exposure correction icon(page 65)h Change the brightness of the
image.
iWhen you specify multiple functions that cannot be simultaneouslyenabled, the function which was last set becomes the active setting, andthe other settings accordingly change automatically.
#: Set the shutter buttontouch sensor to ON.
$: Set the shutter buttontouch sensor to OFF.
k: Shoot at 3,680 2,760
pixels (single-shotshooting mode only
D: Shoot at 2,816 2,112
pixelsz: Shoot at 2,288 1,712
pixels
t: Shoot at 1,600 1,200pixels
[: Shoot at 640 480 pixels
5: Shoot at 320 240 pixels
d: Shoot at 640 480 pixels
: The camera will determinethe setting automatically.
r: For photography in fairweather (sunny) conditions
o: In overcast conditions
p: Under fluorescent lighting
q: Under incandescent
lighting]: For setting the most
accurate white balance
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
63/140
57 English
TOUCH SENSOR (TOUCH FOCUS)SETTINGThe touch sensor function, by which the autofocus is activated by a finger-touch on the shutter button, can be set to ON or OFF. When the touch sensorfunction is set to OFF, the autofocus is activated when you press the shutterbutton halfway; then gently press the shutter button to snap the picture.
1 Display the Recording Menu (page 54).
2 Select TOUCH SENSOR and
press the SET button.h The sensor menu appears.
3 Select the desired icon, and press the SET button.h The selected touch sensor function is set.
CAUTIONiWhen the camera is attached to a tripod, the touch sensor sensibility may
be diminished. This happens because the touch sensor works by detectingchanges in the capacitance when the camera is touched with bare hands.
The touch sensor sensibility will also be diminished, for example, if youhold the camera with gloved hands.
iWhen the camera is used near inverter-type fluorescent lights, the touchsensor sensitivity may be diminished.
#: The touch sensor function is set toON.
$: The touch sensor function is set toOFF.
RECORDING MENU
TOUCH SENSOR
RESOLUTION
FOCUS METHOD
ISO
WHITE BALANCE
EXPOSURE
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
64/140
English 58
RESOLUTION/VIDEO CLIP SETTINGBy setting the image resolution (pixels) to a higher setting, image detail isenhanced for a smoother, finer picture. However, the file size also becomes large
and uses more memory. Select the resolution setting that suits your purpose.
1 Display the Recording Menu (page 54).
2 In the single shot or sequentialshots shooting mode select[RESOLUTION], or in the video cliprecording mode select [VIDEO CLIP
MODE], and press the SET button.h The resolution menu or video clip
mode menu appears.
3 Select the desired icon, and press the SET button.h The selected resolution setting or video clip mode setting is set.
k: Shoot image at 3,680 2,760pixels (Single shot mode only)
D: Shoot image at 2,816 2,112pixels
z: Shoot image at 2,288 1,712 pixels
t: Shoot image at 1,600 1,200 pixels
[: Shoot image at 640 480 pixels
5: Shoot at 320 240 pixels.
d: Shoot at 640 480 pixels.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
65/140
59 English
RESOLUTION/VIDEO CLIP SETTING
Record and play back an audio file
In the video clip recording mode, your camera can make audio recordings.
Record an audio file
1 Display PAGE 1 of the RecordingMenu for the video clip recordingmode (page 54).
2 Select the audio recording icon
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
66/140
English 60
Playing back audio recordingsListen to your audio recordings.
1 Display the desired audio data.h A musical note graphic appears on
the screen.
2 Play back the recording.
To do this... Do this
Forward playback Press the SET button.
Stop playback During playback, press the [o] button
PauseDuring playback, press the SET button.During fast forward or fast reverse, press the[n] button.
Fast forward
During forward playback, press the [m] button.
* The speed changes each time the [m] buttonis pressed, as follows:
Normal playback 2x 5x 10x 15xPress the [l] button to resume normal speed.
Fast reverse
During forward playback, press the [l] button.* The speed changes each time the [l] button
is pressed, as follows:15x 10x 5xPress the [m] button to resume normal speed.
Return to normal playback speed Press the SET button.
Adjusting the volume
Louder:During playback, press [T] on thezoom switch.Softer:During playback, press [W] on thezoom switch.
100-0013
2006.12.24
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
67/140
61 English
FOCUS AREA SETTINGYou can choose from the following 2 types of autofocus (still image shootingonly):
9-point range finder focus: The correct focus is determined from 9 differentfocus points within the shooting area visible on themonitor. When the image is focused, a targetmark&appears.
Spot focus: The camera focuses on the subject in the centerof the monitor.
1 Display the Recording Menu(page 54).
2 Select FOCUS METHOD andpress the SET button.h The focus mode menu appears.
B: 9-point range finder focus isselected.
C: Spot focus is selected.
h When the spot focus setting isselected, the focus mark + appearsin the center of the monitor.
3 Select the desired icon, and pressthe SET button.h The focus area is set.
12
RECORDING MENU
TOUCH SENSORRESOLUTION
FOCUS METHOD
ISO
WHITE BALANCE
EXPOSURE
Focus mark
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
68/140
English 62
ISO SENSITIVITYWith the initial settings, the ISO sensitivity is automatically set according tothe brightness of the subject. However, the ISO sensitivity can be set to a
fixed setting.
1 Display the Recording Menu (page 54).
2 Select ISO and press the SETbutton.h The ISO sensitivity menu appears.
3 Select the desired icon, and press the SET button.h The ISO sensitivity is set.
HINTi By setting a higher ISO sensitivity, you can set higher shutter speeds and
capture images in darker locations, but noise in the captured images mayincrease.
t: Sets the ISO sensitivityautomatically (equivalent toISO50 to 200 [video clip recordingmode: ISO200 to 800]).
*: Sets the sensitivity to ISO50equivalent (video clip recordingmode: ISO200).
u: Sets the sensitivity to ISO100 equivalent (video clip recordingmode: ISO400).
v: Sets the sensitivity to ISO200 equivalent (video clip recordingmode: ISO800).
w: Sets the sensitivity to ISO400 equivalent (video clip recordingmode: ISO1,600).
RECORDING MENU
TOUCH SENSOR
RESOLUTION
FOCUS METHODISO
WHITE BALANCE
EXPOSURE
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
69/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
70/140
English 64
3 Select the desired icon, and press the SET button.h This completes the white balance setting.h Once the white balance setting is programmed for the ]icon, it is
retained even if another white balance setting (>, r, o, p, orq
) is selected. If you changed to another setting, whenever youselect the ]icon and press the SET button, the previouslyprogrammed setting is recalled.
HINTTo cancel the white balance settingi Perform step 1, select>, and then press the SET button.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
71/140
65 English
EXPOSURE CORRECTIONWhen capturing images, you can make the image lighter or darker.
1 Point the camera lens at thesubject, and display theRecording Menu (page 54).
2 Press the [m] and [o] buttons toselect EXPOSURE and pressthe SET button.h The screen to adjust the
exposure appears.
3 Press the [n] or [o] button toselect the exposure numericalvalue, and press the SETbutton.h The specified exposure is set,
and you are returned to the
Recording Menu.
HINTi The exposure correction setting returns to 0 after the camera is turned
off.
RECORDING MENU
EXPOSURE
[o] button
SET button
[n] button
[m] button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
72/140
English 66
PLAYBACKPAGE 1 (BASIC SETTINGS)
DISPLAYING THE PLAYBACK MENUThe Playback Menu is used to adjust your cameras playback settings.
1 Press the playback button [=].h The display changes to the
Playback Screen.
2 Press the MENU button.h The Playback Menu appears.h The Playback Menu is canceled
when the MENU button is
pressed.
PLAYBACK MENU
PROTECT
ROTATE
RESIZE
COPY FILE
PRINT SETTING
SLIDESHOW
Playback button [=]
MENU button
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
73/140
67 English
DISPLAYING THE PLAYBACK MENU
Overview of the Playback Menu
1 [Protect] (page 68)h Protect data from accidental
erasure (write protect).2 [Rotate image] (page 70)h Rotate still images.
3 [Resize] (page 71)h Reduce the resolution of a still
image.
4 [Copy file] (page 72)5 [Print setting] (page 74)h Specify the print settings.
6 [Slideshow] (page 80)h Play back the images in a
slideshow format.
PLAYBACK MENU
PROTECT
ROTATE
RESIZECOPY FILE
PRINT SETTING
SLIDESHOW
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
74/140
English 68
IMAGE PROTECTPrevent accidental erasure of data.
1 Display the data that you want to protect from accidental erasure,and display the Playback Menu (page 66).
2 Select PROTECT and press theSET button.h The screen to set the protect
setting appears.
3 Select YES and press the SETbutton.h The protect mode is set for the
data.h The protect mark Bindicates that
the data is locked.
Activate file protect?ctivate file protect?
YES
OKKEXIT
Cancel file protect?ancel file protect?
YES
OKKEXIT
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
75/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
76/140
English 70
ROTATE IMAGECaptured still images can be rotated to the correct orientation for viewing.
1 Display the image you wish to rotate, and display the Playback Menu(page 66).
2 Select ROTATE and press theSET button.h The screen to rotate the image
appears.
3 Select YES and press the SETbutton.h Each time the SET button is
pressed, the image is rotatedanother 90 degrees.
HINTiOn the 9-image display playback, rotated images are shown in their
original orientation.i An image for which the protect (locked) mode has been set cannot be
rotated.
Rotate image?otate image?
YES
OKK
EXIT
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
77/140
71 English
CHANGING IMAGE SIZE (RESIZE)The size of a still image that has already been captured at a resolution oftor more can be changed to 1,600 1,200 pixels or 640 480 pixels. The
resized image is saved as a separate image.
1 Display the still image whose size you want to change, and displaythe Playback Menu (page 66).
2 Select RESIZE and press the SETbutton.h The screen to change the still
image resolution appears.
3 Select the new image size.
4 Press the SET button.h Resizing begins.
HINTWhy cant the image be resized?iAn image can be resized only to a smaller (or the same) size, not to a
larger size.
2M(1600 1200): The saved image will be 1,600 1,200 pixels.0.3M(640 480): The saved image will be 640 480 pixels.
EXIT: Return to the Playback Menu.
(1600x1200)
(640x480)
EXIT
OKK
Change image resolution?hange image resolution
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
78/140
English 72
COPY DATAImages recorded in the cameras internal memory can be copied to the card,and likewise from the card to the internal memory.
1 Insert the card in the camera (page 14).
2 Display the Playback Menu (page 66).
3 Select FILE COPY and press theSET button.
h The screen to copy files appears.
4 Select the copy direction.
INT MEM HCARD:Copy image data from the internalmemory to the card.CARD HINT MEM:Copy image data from the card to theinternal memory.
* If no card is set in the camera, youcannot copy data.
INT MEM CARD
INT MEMCARD
OKK
Copy file?opy file?
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
79/140
73 English
COPY DATA
5 Press the SET button.h The screen to select the type of
copy appears.h The copy source is shown in the
background on the screen.COPY SINGLE:Copy the data for one image.COPY ALL:Copy all the data from the copysource to the copy destination.
6 Select the desired type of copy.
1 Press the [l] or [m] button to display the image you wish to copy.2 Press the [n] or [o] button to select COPY SINGLE.1 Press the [n] or [o] button to select COPY ALL.
7 Press the SET button.h The files are copied.
INT MEMNT MEM CARDARD
COPY SINGLE
COPY ALL
EXIT
OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
80/140
English 74
PRINT SETTINGSIn addition to using your printer to print out still images captured with yourcamera, as with conventional film, you can have prints made at shops offering
digital print services. Moreover, this camera is DPOF-compatible, so you canuse the camera to specify the number of prints, whether or not the date isdisplayed on the print, and also to specify an index print.
Display the screen to set the print settings
1 Display the Playback Menu (page 66).
2 Select PRINT SETTING and pressthe SET button.h The screen to set the print settings
appears.EACH IMAGE:The print settings are specified foreach individual image.ALL IMAGES:The specified print settings apply toall the still images on the card.ALL CLEAR:Clear all the print settings.
Specify the printingpecify the printinginstructions?nstructions?
EACH IMAGE
ALL IMAGES
ALL CLEAR
OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
81/140
75 English
PRINT SETTINGS
HINTAbout the DPOF formatiDPOF (Digital Print Order Format) is a print order format. You can connect
your camera to a DPOF-compatible printer to produce your prints. You canalso set the print settings (page 108) for the desired images, and then havethe reserved images printed automatically.
About the finished printsi Images that have been rotated will be printed in their original orientation.i The quality of the print output will differ depending on the print service and
printer used.
CAUTIONi It is not possible to set the print settings when there are 10,000 or more
files saved on the card.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
82/140
English 76
Specifying date imprinting and number of printsYou can specify print settings for each individual image (EACH IMAGE), orapply the print settings to all the images on the card (ALL IMAGES).
1 Display the screen to set the print settings (page 74).
2 Select EACH IMAGE or ALL IMAGES.
EACH IMAGE:The set print settings are appliedonly to the image currentlydisplayed.
ALL IMAGES:The set print settings are applied toall the still images on the card.
3 Press the SET button.h The Date/Copies Print Screen
appears.h If EACH IMAGE was selected,
press the [l] or [m] button todisplay the desired image to print.
h The print settings for the currentlydisplayed image are shown in theupper right area of the monitor. Youcan press the [l] or [m] button toconfirm the print settings for eachimage.
Specify the printingpecify the printinginstructions?nstructions?
EACH IMAGE
ALL IMAGES
ALL CLEAROKK
DATE
COPIES 0
EACH IMAGEACH IMAGE
EXIT
NO
OKK
Print settings status
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
83/140
77 English
PRINT SETTINGS
4 Specify the number of prints andwhether the date is imprinted.h Please specify the number of prints
before setting the date imprintsetting. The date imprint settingcannot be set until the number ofprints has been entered.
1 Press the [n] or [o] button to
select COPIES.2 Press the SET button.
h The Print Number Screenappears.
3 Press the [n] or [o] button tospecify the number of prints.h Press the [n] or [o] button until
the desired number of prints isdisplayed.
4 Press the SET button.h You are returned to the Date/
Copies Print Screen.1 Press the [n] or [o] button to
select DATE.2 Press the SET button.h The Print Date Screen appears.
3 Press the [n] or [o] button toselect the desired option.YES:Print the date.NO: Do not print the date.
4 Press the SET button.h You are returned to the Date/
Copies Print Screen.
DATE
COPIES 1
EACH IMAGEACH IMAGE
EXIT
NO
OKK
DATE
COPIES
EXIT
0
EACH IMAGEACH IMAGE
NO
OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
84/140
English 78
5 Select EXIT, and press the SETbutton.h You are returned to the display in
step 2. DATE
COPIES 1
EACH IMAGEACH IMAGE
EXIT
YES
OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
85/140
79 English
PRINT SETTINGS
Clearing all the print settings
Delete the print settings for all images.
1 Display the screen to set the print settings (page 74).
2 Select ALL CLEAR.
3 Press the SET button.h The Confirm All Clear Screen appears.
YES: Clear the print settings for all images.NO: Cancel the clear procedure and return to the screen to set the
print settings.
4 Select YES, and press the SET button.h All the print settings are cleared and you are returned to the screen to
set the print settings.
Specify the printingpecify the printinginstructions?nstructions?
EACH IMAGE
ALL IMAGES
ALL CLEAR
OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
86/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
87/140
81 English
DISPLAYING IMAGE PROPERTIES (INFORMATION SCREEN)On the Information Screen you can check what the settings were when animage was captured.
1 Display the desired image.
2 Press and hold the MENUbutton for at least1 second.h The Information Screen
appears.
h If the MENU button ispressed again, theInformation Screen iscanceled.
1 Resolution setting2 Resolution3 Scene function setting4 Image number
5 Protect setting6 Voice memo setting7 File size8 Aperture value9 Shutter speed0 Exposure correction
settingA Video clip mode settingsB Resolution and frame
rateC File formatD Playback timeE Remaining battery power
713KBF2.8
2816x2112
1/300
I N F O 100-0004
0
4.8MB
15fps
00:00:15
I N F ONF OI N F O 100-0005 5100-0005
320x240
I N F O 100-0006
158KB00:00:20
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
88/140
English 82
OPTION
DISPLAYING THE OPTION MENUThe Option Menu is used to adjust various camera settings.
1 Display the Recording Menu or Playback Menu.h Recording Menu, see page 54h Playback Menu, see page 66
2 Press the [n] or [o] button toselect the option tab 3.h The Option Menu appears.
To exit the Option MenuTo return to the Shooting Screen or Playback Screen
Press the MENU button.To return to the Recording Menu or the Playback MenuWith the option tab 3selected, press the [n] or [o] button.
AUTO
CLOCK SETSOUND
POST VIEW
LCD BRIGHTNESS
LANGUAGE
TV SYSTEM
OPTION MENU(1/2)
OFF
Option tab
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
89/140
83 English
DISPLAYING THE OPTION MENU
Overview of the Option Menu
AUTOOFF
AUTO POWER OFF
FILE NO. RESET
FORMAT
RESET SETTINGS
CLOCK SETSOUND
POST VIEW
LCD BRIGHTNESS
LANGUAGE
TV SYSTEM
OPTION MENU(1/2)
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
90/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
91/140
85 English
SOUNDSSet the sounds (SOUNDS) that are produced by the camera.
1 Display the Option Menu (page 82).
2 Select SOUNDS and press theSET button.h The screen to set the sounds
appears.
OPERATION VOL:Volume setting for all camera buttons.
TURN ON/OFF:Mute or enable the sound that isproduced when the camera is turnedon or off.
SHUTTER:Select the sound that is producedwhen the shutter button is pressed.
KEY SW:Select the sound that is produced
when a camera button (SET button,MENU button, etc.) is pressed.
AUDIO GUIDE:Mute or enable the cameras audiohelp guide.
PLAY VOLUME:Adjust the volume for playing backvideo clips and audio files.
SET
SOUNDOUNDOPERATION VOL
TURN ON/OFF
SHUTTER
KEY SW
AUDIO GUIDE
PLAY VOLUME
3
ON
OFF
OFF
OFF
3OKK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
92/140
English 86
3 Select the desired item, and press the SET button.
4 Press the [n] or [o] button to change the setting.
h The respective screen to enable or disable the sound appears.
ON: Activates the sound.OFF: Deactivates the sound.
h The respective screen to select the sound appears.h Select from 5 different sounds (A to E) and OFF.h After selecting a sound, press the [m] button to preview it.h If OFF is selected, no sound is produced.
h The screen to select the volume setting appears.h You can select a volume setting from 1 (minimum) to 5 (maximum).h If OFF is selected, no sound is produced.
5 Press the SET button.h The sound settings are completed.h
To return to the Option Menu, press the MENU button.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
93/140
87 English
POST-VIEW SETTINGSpecify the duration that the captured image appears on the monitor (post-view) after the shutter button is pressed.
1 Display the Option Menu (page 82).
2 Select POST VIEW and press theSET button.h The Post View Menu appears.
1SEC:The post-view image is displayed
for 1 second.2SEC:The post-view image is displayedfor 2 seconds.OFF:The post-view image is notdisplayed.
3Select the desired setting, and press the SET button.h This completes the post-view setting.
CLOCK SETSOUND
POST VIEW
LCD BRIGHTNESSLANGUAGE
TV SYSTEM
OPTION MENU(1/2)
1SEC
2SEC
OFF
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
94/140
English 88
SCREEN LANGUAGEYou can set the monitor of your camera to display the messages in any one ofseveral languages.
1 Display the Option Menu (page 82).
2 Select LANGUAGE and press theSET button.h The screen to select the display
language appears.
DEUTSCH: GermanENGLISH: EnglishESPAOL: SpanishFRANCAIS: FrenchITALIANO: ItalianNEDERLANDS:Dutch
: Russian: Japanese: Korean
: Chinese (traditional)
: Chinese (simplified)
3 Select the desired language, and press the SET button.h The selected display language is set.
LANGUAGEANGUAGE
OK
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
95/140
89 English
TV SYSTEM SETTINGSpecify the type of image signal that is output from your cameras PC/AVterminal.
1 Display the Option Menu (page 82).
2 Select TV SYSTEM and press theSET button.h The TV System Menu appears.
NTSC:Outputs NTSC video signals.
PAL:Outputs PAL video signals.
3 Select the desired setting, andpress the SET button.h The selected TV system is set.
HINTIf no image appears on the TV...i If the TV system setting is not correct for the connected equipment, no
image will appear on the TV.
CLOCK SETSOUND
POST VIEW
LCD BRIGHTNESSLANGUAGE
TV SYSTEM
OPTION MENU(1/2)
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
96/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
97/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
98/140
English 92
FILE No. RESET FUNCTIONIf a newly formatted (page 95) card is used, the file name (image number) ofthe captured image automatically begins from 0001. If the card is
subsequently reformatted, or if a different reformatted card is used, the filenames again begin from 0001. This is because the file number reset functionis set to ON, and consequently it results in more than one card containingimages with the same numbers. By setting the file number reset function toOFF, even if the card is reformatted or the card is replaced with anothercard, the consecutive numbering of file names continues from the last numberrecorded by the camera.
File name (image number)Card A 0001, 0002 ......0012, 0013
Card B 0001, 0002 ......0012, 0013
File name (image number)Card A 0001, 0002 ......0012, 0013
Card B 0014, 0015 .......0025, 0026
Replace card
Replace card
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
99/140
93 English
FILE No. RESET FUNCTION
i If Card B already has image data in it when it replaces Card A, file namesare assigned as follows.
When the highest image number on Card B (before replacing) islower than the highest image number on Card A: the file name of thenext recorded image continues from last file name recorded on Card A.
When the highest image number on Card B (before replacing) ishigher than the highest image number on Card A: the file name of thenext recorded image continues from last file name recorded on Card B.
HINTWhat about the internal memory?
i The file number reset function works the same for the internal memory.
Card A 0001, 0002......0012, 0013
Card B 0001, 0002, 0014, 0015...... 0025, 0026
Previously recorded images
Replace card
Card A 0001, 0002......0012, 0013
Card B 0020, 0021, 0022, 0023...... 0025, 0026
Previously recorded images
Replace card
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
100/140
English 94
1 Display the Option Menu (page 82).
2 Select FILE NO. RESET and pressthe SET button.h The File Number Reset Menu
appears.ON:The file number reset function is ON.OFF:The file number reset function isOFF.
3 Select OFF, and press the SET button.h The file number reset function was set to OFF.
HINTiUntil the file number reset function is turned ON, consecutive file names
are assigned. It is recommended that the file number reset function bereturned to ONat the end of each photography session.
AUTO POWER OFF
FILE NO. RESET
FORMAT
RESET SETTINGS
OPTION MENU(2/2)
ON
OFF
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
101/140
95 English
INITIALIZING THE CARD MEMORY AND INTERNAL MEMORYA card must be formatted with this camera:iAfter purchasing, when used for the first time, or
i If it was formatted using a personal computer or another digital camera.The card cannot be reformatted if the lock switch is set to the LOCKposition. Proceed with the reformat procedure after setting the lock switch tothe unlocked position.
1 To reformat a card, install it in the camera. To reformat the camerasinternal memory, remove the card from the camera.
2 Display the Option Menu (page 82).
3 Select FORMAT and press theSET button.h The screen to select the type of
format appears.h Follow steps 4to 6.
FORMAT:A normal formatting is executed.FULL FORMAT:The entire card is scanned andreformatted. It is not possible toselect this when there is no cardinstalled, or when the remainingbattery charge is low.
h The screen to begin formatting
appears.h Follow steps 5and 6.
FORMAT ( CARD)ORMAT CARD)
FORMAT
FULL FORMAT
OKK
YESNO
OKK
Format the internal memory?ormat the internal memory
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
102/140
English 96
4 Select the desired format option, and press the SET button.h The Confirm Format Screen appears.
5 Select YES.
6 Press the SET button.h Formatting begins.h During formatting, FORMATTING and DO NOT POWER OFF are
shown on the monitor.
CAUTION
Caution during reformattingi Please do not turn off the camera or insert/remove the card while the cardis being formatted.
Reformatting erases the dataiWhen the card or internal memory is initialized, all the recorded data is
erased. Protected data is also erased, so before reformatting a card, anydata you want to keep should be copied to your personal computers harddisk or other storage medium.
Caution regarding disposing/transferring the card (recovering data froma reformatted card)i If a card is reformatted or the data is erased from the card using the
camera or a computer, the cards control data may be merely modified andthe data itself may not be completely erased from the card.
i In some cases it may be possible to recover the data from a reformattedcard using special software for that purpose. However, if the camera isused to execute a full format, it will be impossible to recover the data evenby the use of data recovery software.
i If you are disposing of a card, it is recommended that you physicallydestroy it. If you are transferring the card to someone else to use, it isrecommended that you use the cameras full format function to reformatthe card, or use commercially available software for erasing card data.Managing data is the responsibility of the user.
HINTTo cancel reformattingi
In step 5, select NO, and press the SET button.
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
103/140
97 English
RESETTING THE CAMERA SETTINGSReset the camera to the factory-preset settings.
1 Display the Option Menu (page 82).
2 Select RESET SETTINGS andpress the SET button.h The Reset Settings Menu appears.
YES:Reset to the factory-preset settings.NO:
Do not change the settings, andreturn to the Option Menu.
3 Select YES, and press the SETbutton.h The camera settings are reset to
the factory-preset settings.
HINTiNote that the following settings do not change with this procedure:
Date and time settingLanguage setting
AUTO POWER OFF
FILE NO. RESET
FORMATRESET SETTINGS
OPTION MENU(2/2)
YES
NO
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
104/140
English 98
CHECKING THE REMAINING INTERNALMEMORY AND CARD MEMORY
You can check the possible number of images, audio recording time andvideo clip recording time remaining on the card. For a table showing themaximum number of images and recording time for the internal memory andfor a specific card, please see Possible Number of Images/Video RecordingTime/Audio Recording Time on page 128.
1 Press the ON/OFF button to turn thecamera on.
Set the shooting mode to the singleshot or sequential shots shootingmode (page 27).Set the shooting mode to the videoclip recording mode (page 27).
h The remaining recording time isshown on the monitor.h The remaining number of images
and video recording time will differdepending on the resolution setting.
Remaining number of images
Remaining recording time
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
105/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
106/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
107/140
101 English
CHECKING THE REMAINING BATTERY CHARGE
HINTi If any data is present, you can also check the remaining battery charge on
the Information Screen (page 81).iBattery life may differ even among batteries of the same type.iDepending on the usage of the camera (such as the number of times the
flash is used, etc.) or the ambient temperature (temperatures below 10C[50F]) the number of images that can be saved on fully charged batterieswill vary greatly.
i It is recommended that you prepare extra batteries when taking pictures ata wedding or while traveling, for example, so you dont miss capturingimages of important moments due to the battery power running out. The
same is recommended for taking photos in cold environments. (In a skiarea, for example, the batteries can be kept warm in your pocket untilready to use.)
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
108/140
English 102
OTHER DEVICES AND CONNECTIONS
CONNECTING TO A TVConnect the supplied AV interface cable from the PC/AV terminal on thedigital camera to the AUDIO and VIDEO input terminals on the TV.
Playbacki After connecting the digital camera to the television, set the TV input switch
to VIDEO input.iWhen an AV interface cable is connected, no image appears on the
cameras monitor.i The playback method is the same as when viewing images on the
cameras monitor.i The same playback procedure as when playing back with the camera is
used to play back voice memos and audio recordings as well.Voice memo playback: see page 33
Audio playback: see page 60
CAUTIONInsert and pull out the cable carefullyiWhen connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on thedevices. Push the plugs in straight when connecting them. If undue force isused to connect a cable, it may permanently damage the connector pins inthe terminal socket.
iDo not use excessive force when connecting and disconnecting cables.
PC/AVTo the VIDEO input
terminal
White plug To the PC/AVterminal
Yellow plug
To the AUDIO inputterminal
Switch input to VIDEO
Supplied dedicatedAV interface cable
PC/AV terminal
Open
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
109/140
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
110/140
English 104
3 Select PictBridge, and press theSET button.h The screen to select the images to
print appears.
CAUTIONCaution when connecting a printeri If the power to the printer is turned off while it is connected, the camera
may not operate correctly. If the camera does not operate correctly,disconnect the USB interface cable, turn off the camera, and thenreconnect the cable.
iDuring PictBridge printing, the cameras button operation response isslower.
i If the camera is powered by batteries for printing, make sure that theremaining battery charge is sufficient.
Insert and pull out the cable carefullyiWhen connecting the cables, make sure that the cable plugs are correctly
oriented and that they match the shapes of the terminal sockets on thedevices. Push the plugs in straight when connecting them. If undue force isused to connect a cable, it may permanently damage the connector pins inthe terminal socket.
iDo not use excessive force when connecting and disconnecting cables.
PRINT
PRINTRINT
Print this image?rint this image?
COPIES 1
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
111/140
105 English
DIRECT PRINTING
To select one image and print it (displayed image)
Procedure to select one still image and print it.
1 Complete the printing setup (page 103).
2 Press the [l] or [m] button.h Specify the image to print.
PRINT
PRINTRINT
Print this image?rint this image?
COPIES 1
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
112/140
English 106
3 Specify the number of prints.1 Select COPIES, and press the
SET button.2 Press the [n] or [o] button to
specify the number of prints.3 Press the SET button.
4 Select PRINT, and press the SETbutton.h Printing begins.
HINT
To cancel printing1 During printing, press the [o] button.h The Confirm Cancel Printing Screen appears.
2 Select YES, and press the SET button.h If EXIT is selected and the SET button is pressed, printing resumes.
OKK
Print this image?rint this image?
COPIES 1
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
113/140
107 English
DIRECT PRINTING
To print all the images (all images)
Print all of the images.
1 Complete the printing setup (page 103).
2 Press the MENU button.h The PictBridge Menu appears.
3Select PRINT ALL IMAGES, andpress the SET button.h The Print All Images Screen
appears.
4 Select PRINT, and press the SETbutton.h Printing begins.
CAUTIONPrinting is not possible if there are more than 999 still images in thecard.iDelete unwanted images before printing.
PictBridge MENU
PRINT IMAGEPRINT ALL IMAGES
DPOF
PRINTEXIT
PRINTRINT
Print all images?rint all images
-
8/10/2019 Camera_sanyo VPC-S60EX/VPC-S60
114/140
English 108