BUILDING LIGHTING AUTOMATION THROUGH THE
INTEGRATION OF DALIWITH WIRELESS SENSOR
NETWORKS
ABSTRACT• This paper focuses on the integration of Digital Addressable Lighting
Interface (DALI) devices in wireless sensor networks.• Since different manufacturers usually deal with one aspect of
building automation - e.g. heating ventilation and air conditioning, lighting control, different kinds of alarms, etc. - final building automation system has different subsystems which are finally taken to an integrated building management system.
• The cost of this process is consequently increased due to additional hardware investment.
• Our main purpose is to provide the end consumer with an economical fully centralized system in which home appliances are managed by an IEEE 802.15.4-based wireless sensor network
• . Not only is it necessary to focus on the initial investment, but maintenance and energy consumption costs must also be considered.
EXISTING SYSTEM
• wired net works used
• High cost.
• Network extensions limited.
• Limited features.
• Complex network protocols (like x10,BAc).
PROPOSED SYSTEM
• Our main purpose is to provide the end consumer with an economical fully centralized system in which home appliances are managed by an IEEE 802.15.4-based wireless sensor network
• Low cost
HARDWARE
• MICRO CONTROLLER
• WIRELESS(ZIGBEE OR GSM) MODULE
• ILLUMINATION CONTROL UNIT
• RELAY
SOFTWARE
• EMBEDDED ‘C’ LANGUAGE
• KEIL IDE
• SUNROM PROGRAMMER
• EAGLE CAD SOFT
BUILDING MODULE
M
C
U
ILLUMINATION
CONTROLUNIT
LAMP 1 LAMP 2
LAMP 3Load control
Unit LAMP 3
SERIALINTERFACE
MICROCONTROLLERZIGBEE
TRANSIVER
LDR
MONITORING NODE
ZIGBEE TRANSIVER
SERIALINTERFACE
MAX232PC VB6.0
MICRO CONTROLLER(AT89S52)
FEATURES
• Compatible with MCS-51® Products• 8K Bytes of In-System Programmable Flash
Memory• SPEED Up to 33 MHz• Three-level Program Memory Lock• 256x 8-bit Internal RAM• 32 Programmable I/O Lines• Three 16-bit Timer/Counters• Six Interrupt Sources• Full Duplex UART Serial Channel• Flexible ISP Programming
SERIAL DATA COMMUNICATION
• MAX232 is used here to interface zigbee with microcontroller
• The MAX232 device is a dual driver/receiver that includes a capacitive voltage generator to supply RS-232 voltage levels from a single 5-V supply.
• Each receiver converts RS-232 inputs to 5-VTTL/CMOS levels.
ILLUMINATION CONTROL UNIT
Features and benefits Direct triggering from low powerdrivers and logic ICs High blocking voltage capability Low holding current for low current Planar passivated for voltageruggedness and reliability Sensitive gate Triggering in all four quadrants
TRIAC BT136 FEATURES• TRIAC, 4A, 600V, TO-220 • Peak Repetitive Off-State Voltage, Vdrm: 600V • On State RMS Current IT(rms): 4A • Peak Non Rep Surge Current Itsm 50Hz: 25A • Gate Trigger Voltage Max Vgt: 1.5V • Peak Gate Power: 5W • Operating Temperature Range: -40°C to +150°C • No. of Pins: 3 • SVHC: No SVHC (18-Jun-2012) • Current Itsm: 25A • Current Itsm @ 60Hz: 27A • Current t2+g-: 35mA • Current t2-g+: 70mA • Current t2-g-: 35mA • Device Marking: BT136-600 • Gate Trigger Current Igt (Q1) t2+g+: 35mA • Gate Trigger Current Max, Igt: 70mA • Holding Current Max Ih: 15mA • Package / Case: TO-220AB • Repetitive Reverse Voltage Vrrm Max: 600V • Termination Type: Through Hole • Thyristor Type: Triac
DIAC
• .: 100 Breakover Current Max µA•Thyristor Case: DO-35 • . : 2 No of Pins•Diode Type: Diac • : 2 External Diameter mm•External Length / Height: 4.5mm • / : -35 Package Case DO•Power Dissipation Ptot Max: 150mW •Repetitive Peak Forward Current Itrm: 2A • : Thyristor Type Diac• : 5 Voltage Vo V
OPTO COUPLER
• OPTOCOUPLER, TRIAC DRIVER • No. of Channels: 1 • Isolation Voltage: 7.5kV • Optocoupler Output Type: Phototriac • Input Current: 10mA • Output Voltage: 400V • Opto Case Style: DIP • No. of Pins: 6 • SVHC: No SVHC (18-Jun-2012) • Approval Bodies: UL • Blocking Voltage: 400V • Operating Temperature Range: -40°C to
+85°C • RMS Current Max: 100mA • Threshold Current If on: 15mA • Trigger Current If Max: 15mA
RELAY & RELAY DRIVER ULN 2003
Relay drive
• Ideally suited for interfacing between low-level logic circuitry and multiple peripheral power loads, the Series ULN20xxA/L high-voltage, high-current Darlington arrays feature continuous load current ratings to 500 mA for each of the seven drivers.
INTERNAL CIRCUIT OF ULN 2003-DRIVER CIRCUIT
SPECIFICATIONS OF ULN 2003
RELAY
• A relay is an electrical switch that opens and closes under control of another electrical circuit. In the original form, the switch is operated by an electromagnet to open or close one or many sets of contacts
• Relay is used here to energize the load.
APPLICATIONS
• Domestic appliance, office machine, audio, equipment, automobile, etc (Remote control TV receiver, monitor display, audio equipment high rushing current use application)
• Rating:• CCC File Number: CH0052885-2000 7A/240VDC• CCC File Number: CH0036746-99 10A/250VDC• UL/CUL File Number: E167996 10A/236VAC 28VDC• TUV File Number: R9933789 10A/240VAC 28VDC
ZIGBEE
CONCLUSION• DALI PERFORMANCE• REMOTE MANAGEMENT SYSTEM
• SAVING ENERGY • MAINTENANCE PURPOSES• DETECT ANY SINGLE LAMP FAULT