STRUCTURAL CONCRETE SOFTWARE SYSTEM
Consulting Company Member
POST-TENSIONINGINSTITUTE
email: [email protected] website: http://www.AdaptSoft.com1733 Woodside Road, Redwood City, California, 94061, USA, Tel: (650) 306-2400 FAX: (650) 364-4678
BUILDER
ADAPT-MODELEREXAMPLES
Copyright 2002
ModExamples_Title.p65
Dr. Bijan O. AalamiStructural Engineer
i
ADAPT MODELER TUTORIAL
ADAPT-Modeler Examples
OVERVIEW
This compilation contains several typical examples of floor systems that have been modeled usingADAPT-Modeler. The first example (Shiraz Building) is the same used in the tutorial manual ofADAPT-Modeler.
In general, there is more than one way to define load paths for a given floor system. The optionspresented in the examples presented are viewed to be in line with common industry practice.
ii
ADAPT MODELER TUTORIAL
This Page Left Intentionally
BLANK
iii
ADAPT MODELER TUTORIAL
LIST OF CONTENTS
EXAMPLES ..................................................................................................................................... 1-11.1 EXAMPLE 1 - THE SHIRAZ BUILDING ............................................................... 1-11.2 EXAMPLE 2 - THE PROSPERITY SLAB .............................................................. 1-91.3 EXAMPLE 3 - SLAB AND BEAM PARKING STRUCTURE ............................. 1-191.4 EXAMPLE 4 - THE RAMSON BUILDING, IRREGULAR
TWO-WAY SLAB ................................................................................................... 1-271.5 EXAMPLE 5 – A HIGHRISE BUILDING IN JAKARTA, INDONESIA.............. 1-35
iv
ADAPT MODELER TUTORIAL
This Page Left Intentionally
BLANK
EX - 1
ADAPT MODELER EXAMPLES
EXAMPLES
1.1 Example 1 - The Shiraz Building
This example is the two-way flat slab used for the tutorial in the previous chapter. Thecompleted model is contained in the Example1.DWG file included in the program CD-ROM.The model file is complete and ready to export data to ADAPT-PT. Below are sample planoutputs for the example.
EX - 2
ADAPT MODELER EXAMPLES
EX - 3
ADAPT MODELER EXAMPLES
EX - 4
ADAPT MODELER EXAMPLES
EX - 5
ADAPT MODELER EXAMPLES
EX - 6
ADAPT MODELER EXAMPLES
EX - 7
ADAPT MODELER EXAMPLES
EX - 8
ADAPT MODELER EXAMPLES
EX - 9
ADAPT MODELER EXAMPLES
1.2 Example 2 - The Prosperity Slab
This example is a two-way flat slab with irregular support layout, introduced in the PTIpublication Design Fundamentals of Post-Tensioned Concrete Floors. Drop caps and droppanels have been included at several locations, as well as a wide shallow beam at one edge ofthe slab. Figures 1.2-1 and 1.2-2 summarize the model geometry. On the following pages aresample output for the model.
FIGURE 1.2-1
EX - 10
ADAPT MODELER EXAMPLES
FIGURE 1.2-2
EX - 11
ADAPT MODELER EXAMPLES
EX - 12
ADAPT MODELER EXAMPLES
EX - 13
ADAPT MODELER EXAMPLES
EX - 14
ADAPT MODELER EXAMPLES
EX - 15
ADAPT MODELER EXAMPLES
EX - 16
ADAPT MODELER EXAMPLES
EX - 17
ADAPT MODELER EXAMPLES
EX - 18
ADAPT MODELER EXAMPLES
This Page Left Intentionally
BLANK
EX - 19
ADAPT MODELER EXAMPLES
1.3 Example 3 - Slab and Beam Parking Structure
This example illustrates a typical beam and slab parking deck. Sample outputs are includedbelow.
EX - 20
ADAPT MODELER EXAMPLES
Note, the slab region, including ramp area, has been modeled all on the same level. Thecutout in the slab region (between G9 and G10) represents the discontinuity at the ramp.
EX - 21
ADAPT MODELER EXAMPLES
Notice that the one-way slab was run so that only a small portion of the slab was covered.This was done with domain splitters as described in the Program and User Interface Manuals.
EX - 22
ADAPT MODELER EXAMPLES
Note, support lines along G6 through G10 are split into two support lines to reflect thediscontinuity due to the ramp. Other support lines are continuous across the structure.
EX - 23
ADAPT MODELER EXAMPLES
EX - 24
ADAPT MODELER EXAMPLES
EX - 25
ADAPT MODELER EXAMPLES
Note, splitters are used to define the design strips in the X-direction (two slab strips and onetransfer beam strip). The transfer beam loads must be adjusted in ADAPT-PT to reflect thetrue loading on the design strip (to include reactions of transverse beam). Splitters 1-4 arestrip splitters; 5-7 are domain splitters.
EX - 26
ADAPT MODELER EXAMPLES
Note, splitter 8 is used to delineate design strips at the ramp into two separate strips at eachgridline.
EX - 27
ADAPT MODELER EXAMPLES
1.4 Example 4 - The Ramson Building, Irregular Two-way Slab
This example illustrates the versatility of using Modeler’s splitter and connector features toassign load paths in an irregular two-way slab. The complete DWG file (Example4.DWG)has been included with the software.
EX - 28
ADAPT MODELER EXAMPLES
EX - 29
ADAPT MODELER EXAMPLES
EX - 30
ADAPT MODELER EXAMPLES
EX - 31
ADAPT MODELER EXAMPLES
EX - 32
ADAPT MODELER EXAMPLES
EX - 33
ADAPT MODELER EXAMPLES
EX - 34
ADAPT MODELER EXAMPLES
This Page Left Intentionally
BLANK
EX - 35
ADAPT MODELER EXAMPLES
1.5 Example 5 – A Highrise Building in Jakarta, Indonesia
This example illustrates an irregular beam and slab construction. The complete DWG file(Example5.DWG) has been included with the software.
EX - 36
ADAPT MODELER EXAMPLES
EX - 37
ADAPT MODELER EXAMPLES
EX - 38
ADAPT MODELER EXAMPLES
EX - 39
ADAPT MODELER EXAMPLES
EX - 40
ADAPT MODELER EXAMPLES
EX - 41
ADAPT MODELER EXAMPLES
EX - 42
ADAPT MODELER EXAMPLES