BOPP FILMSTECHNICAL DATA SHEETS
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
TRANSPARENT FILMS
GP Transparent heat sealable BOPP film for printing, lamination and packaging
SG Transparent non-heat sealable BOPP film for scotch tape
FG Transparent non-heat sealable BOPP film for printing and decorative package
GPR Transparent non-heat sealable BOPP film with release effect for flexible packaging with glue border of cold adhesion
GPLS Transparent heat sealable BOPP film with low heat sealing properties for printing, lamination and packaging
GA Transparent heat sealable anti-fog BOPP film for printing and packaging
TOBACCO FILMS
TG Transparent heat sealable non-shrinkable BOPP film for “soft” paper packs packaging on high-speed machines
TS Transparent heat sealable shrinkable BOPP film with low coefficient of friction for “hard” paper packs packaging on high-speed machines
TSH Transparent heat sealable shrinkable BOPP film with a very low coefficient of friction for “hard” paper packs packaging on high-speed ma-
chines
TSLS Transparent heat sealable shrinkable BOPP film with a low threshold of heat sealability with a very low coefficient of friction for “hard” paper
packs packaging on high-speed machines
TSP Transparent heat sealable shrinkable BOPP film with a very low coefficient of friction for “hard” paper packs packaging on the high-speed
machines
MATTE FILMS
MP BOPP film with matte side and glossy treated side for printing and lamination
MPLS BOPP film with matte heat sealable side with a low threshold of heat sealability and glossy treated side for printing and lamination
MPRBOPP film with matte side with release effect for production of flexible packaging with glue border of cold adhesion and glossy treated side for
printing and lamination
MPP BOPP film with matte side and glossy side and double-sided treatment for printing and lamination
MDS BOPP film with matte on both sides and treatment on one side for printing and packaging
CAVITATED FILMS
WP White heat sealable BOPP film with a low coefficient of friction for printing, lamination and packaging
PP White-pearlized cavitated heat sealable BOPP film for printing, lamination and packaging
PPLS White-pearlized cavitated heat sealable with low heat sealability BOPP film for printing, lamination and packaging
LABEL FILMS
GL Transparent BOPP label film
PL White-pearlized BOPP label film
PLG White-pearlized BOPP label film with high gloss
PLMM Metallized on white-pearlized cavitated base BOPP label film
METALLIZED FILMS
GMM Metallized on transparent base heat sealable BOPP film for printing, lamination and packaging
GMPM Metallized on transparent base non-heat sealable BOPP film for printing, lamination and decorative packaging
GMBM Metallized on transparent base BOPP film for printing, lamination and packaging
GMLSM Metallized on transparent base heat sealable with low heat sealing threshold BOPP film for printing, lamination and packaging
PMM Metallized on cavitated white-pearlized layer heat sealable BOPP film for printing and lamination
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable BOPP film for printing, lamination and packaging
GP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
12 15 18 20 25 30 35 40 48
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 10,92 13,65 16,38 18,20 22,75 27,30 31,85 36,40 43,68
Tensile strengthMD N/mm²
(MPa)not less ASTM D882
ISO 527GOST 14236
130 140
TD 230 250
Elongation at breakMD
% not more220 200
TD 80 70
Kinetic coefficient of friction
untreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 3 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 2,2 2,3 2,5 2,8
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 105-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,5 3,0 3,2
Gloss untreated side % not lessASTM D2457
ISO 281385
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of production
Main characteristics• low coefficient of friction• good optical properties• contains slip-antistatic and anti-block additives
ApplicationFor packing
• different products: food industry, goods for household use, for industrial goods and others• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack • self using in decorative packaging
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint• method of direct and reverse printing
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent non-heat sealable BOPP film for scotch tape
SG
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
18 20 23 25 26 27 28 30 32 35 40
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 16,38 18,20 20,90 22,80 23,70 24,57 25,50 27,30 29,10 31,90 36,40
Tensile strengthMD N/mm²
(MPa)not less ASTM D882
ISO 527GOST 14236
150 140
TD 250
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of friction
untreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,35
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec* - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,0
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction
Main characteristics• good optical properties – transparency and gloss• good mechanical properties• low shrinkable for maintaining print sizes during glue drying
Application• use for adhesive tapes production – the scotch with melt and waterborne glues• self using in decorative package
For lamination• with other films and materials (if necessary)• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent non-heat sealable BOPP film for printing and decorative package
FG
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 18,20 22,80 27,30 31,90 36,40
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
140
TD 250
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,4
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,0
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction
Main characteristics• high coefficient of friction• high transparency and gloss• used as a face film of a package with high gloss
Application• for exepting heat sealability on the package front side• for manual and machine product wrapping (flowers, gifts, office, textile products etc.)
For packing• for excepting heat sealability
For lamination• with other films and materials (if necessary) • with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent non-heat sealable BOPP film with release effect for flexible packaging with glue border of cold adhesion
GPR
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 20 25 30 35
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 13,65 18,20 22,75 27,30 31,85
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
150 140
TD 250
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 2 2
Heat sealing strength at 130˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,0
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse DirectionKinetic coefficient of friction in 15 days from the date of production
Main characteristics• high release characteristics• low coefficient of friction• high transparent
Application• for reopening/reclosing of package
For packing• on the HFFS packaging machines• with cold (using cold glue) seal formation• with cold glue for one-and reopening
For lamination• with other films and materials • with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable BOPP film with low heat sealing properties for printing, lamination and packaging
GPLS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 18,20 22,80 27,30 31,90 36,40
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
130
TD 250
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,3 2,5 2,8
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 80-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
3,0
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• low heat sealing temperature• low coefficient of friction• good optical properties
Application• to reduce the temperature of heat sealing• to increase the speed of heat sealing
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formed at lower heat sealing temperatures (from 80°C)• Flow-Pack• self using in decorative packaging
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint• method of direct and reverse printing
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable anti-fog BOPP film for printing and packaging
GA
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 18,20 22,80 27,30 31,90 36,40
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
130 140
TD 230 250
Elongation at breakMD
% not more220 200
TD 80 70
Kinetic coefficient of friction
non-functional side/non-functional side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,25functional side/functional side
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 2 2
Heat sealing strength at 130˚С, 1 bar, 1 sec
functional side/non-functional side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,3 2,8
Heat sealing temperaturefunctional side/
non-functional side0С - WATERFALL PRO 120-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
3,0 3,2
Gloss non-functional side % not lessASTM D2457
ISO 281385
Surface tension non-functional sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
Anti-fog properties functional side point not less WATERFALL PRO 4
MD – Machine Direction; TD – Transverse DirectionFunctional side – side with anti-fog effect
Main characteristics• good anti-fog properties from + 4°C and above• low coefficient of friction• one side has anti-fog properties• the other side is for printing
Application• for packaging products which require no fogging, contributing to the preservation of the basic properties of perishable products: fresh vegetables, salads, fruits, hot food, semi-finished products of flour products (dough), etc.
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formation• Flow-Pack
For lamination• with other films and materials (the change in anti-fog properties after lamination was not studied)• with method of the solvent lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint• method of direct printing
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable non-shrinkable BOPP film for “soft” paper packs packag-ing on high-speed machines
TG
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
16 18 20 25 30
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 14,56 16,40 18,20 22,80 27,30
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
130 140
TD 230 250
Elongation at breakMD
% not more220 200
TD 80 80
Kinetic coefficient of friction
outer side in a roll /outer side in a roll
-+0,05-0,10
ASTM D1894ISO 8295
GOST 27492
0,25
inner side in a roll /inner side in a roll
0,3
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec
inner side in a roll /outer side in a roll
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperatureinner side in a roll /outer side in a roll
0С - WATERFALL PRO 105-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,5
Gloss outer side in a roll % not lessASTM D2457
ISO 281385
MD – Machine Direction; TD – Transverse Direction
Main characteristics• standart shrinkable• standart coefficient of friction• high rigidity• high gloss• high transparent
Application• for wrapping “soft” and “hard” paper packs of cigarettes, cigarette blocks, tea, marshmallows, sweets, perfumes, etc.
For packing• on the high-speed HFFS packaging machines without a thermotunnel• with hot (heat sealing) seal formation• “soft” and “hard” paper packs and boxes
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Reeling• Maximum roll diameter: 500 mm• Film width in a roll from 90 to 450 mm• Diameter of paper cores (inside): 76 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable shrinkable BOPP film with low coefficient of friction for “hard” paper packs packaging on high-speed machines
TS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
16 18 20
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 14,56 16,38 18,20
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
150
TD 260
Elongation at breakMD
% not more180
TD 65
Kinetic coefficient of friction
outer side in a roll /outer side in a roll
(slippery side / slippery side)-
+0,05-0,10
ASTM D1894ISO 8295
GOST 27492
0,25
inner side in a roll / inner side in a roll
(non-slip side / non-slip side)0,3
Shrinkage at 120˚С, 5 minMD
% -ASTM D1204
ISO 11501GOST 18616
6,5-9,0
TD 6,5-9,0
Heat sealing strength at 130˚С, 1 bar, 1 sec
inner side in a roll / outer side in a roll
(non-slip side / slippery side)N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature inner side in a roll /outer side in a roll
(non-slip side / slippery side)
0С - WATERFALL PRO 105-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,5
Glossouter side in a roll
(slippery side)% not less
ASTM D2457ISO 2813
85
MD – Machine Direction; TD – Transverse Direction
Main characteristics• high hardness• high gloss • high transparent• low stable coefficient of friction, including over heated surfaces
Application• for wrapping “hard” paper packs of cigarettes, cigarette blocks, tea, marshmallows, sweets, etc.• for film tightening of packs due to shrinkable properties of the film• for tightening packs small and medium sizes
For packing• on the high-speed HFFS packaging machines with a thermotunnel• on the high-speed HFFS packaging machines without a thermotunnel where the film shrink is able due to heating of the weld seal• with hot (heat sealing) seal formation• “hard” paper packs
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Reeling• Maximum roll diameter: 500 mm• Film width in a roll from 90 to 450 mm• Diameter of paper cores (inside): 76 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable shrinkable BOPP film with a very low coefficient of friction for “hard” paper packs packaging on high-speed machines
TSH
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
16 18 20
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 14,56 16,38 18,20
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
140
TD 260
Elongation at breakMD
% not more180
TD 70
Kinetic coefficient of friction
outer side in a roll /outer side in a roll
(slippery side / slippery side)- ±0,05
ASTM D1894ISO 8295
GOST 27492
0,15
inner side in a roll / inner side in a roll
(non-slip side / non-slip side)0,2
Shrinkage at 120˚С, 5 minMD
% ±1,0 ASTM D1204ISO 11501
GOST 18616
8,5
TD 6,5
Shrinkage at 130˚С, 15 minMD
% ±2,012,0
TD 12,0
Heat sealing strength at 130˚С, 1 bar, 1 sec
inner side in a roll /outer side in a roll
(non-slip side / slippery side)N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature inner side in a roll /outer side in a roll
(non-slip side / slippery side)
0С - WATERFALL PRO 105-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,8
Glossouter side in a roll
(slippery side)% not less
ASTM D2457ISO 2813
85
MD – Machine Direction; TD – Transverse Direction
Main characteristics• resistant to scratching and abrasion• low stable coefficient of friction asymmetric, including over heated surfaces• high hardness• high transparent• high gloss
Application• for wrapping “hard” paper packs of cigarettes, cigarette blocks, tea, marshmallows, sweets, etc.• for film tightening of packs due to shrinkable properties of the film• for tightening packs small and medium sizes
For packing• on the high-speed HFFS packaging machines with a thermotunnel• on the high-speed HFFS packaging machines without a thermotunnel where the film shrink is able due to heating of the weld seal• with hot (heat sealing) seal formation• “hard” paper packs
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Reeling• Maximum roll diameter: 500 mm• Film width in a roll from 90 to 450 mm• Diameter of paper cores (inside): 76 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable shrinkable BOPP film with a low threshold of heat sealability with a very low coefficient of friction for “hard” paper packs packaging on high-speed machines
TSLS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
20 25 30
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 18,20 22,75 27,30
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
140
TD 260
Elongation at breakMD
% not more160
TD 70
Kinetic coefficient of friction
outer side in a roll / outer side in a roll
(slippery side / slippery side)- ±0,05
ASTM D1894ISO 8295
GOST 27492
0,15
inner side in a roll / inner side in a roll
(non-slip side / non-slip side)0,2
Shrinkage at 120˚С, 5 minMD
% ±1,0 ASTM D1204ISO 11501
GOST 18616
8,5
TD 6,5
Shrinkage at 130˚С, 15 minMD
% ±2,012,0
TD 12,0
Heat sealing strength at 130˚С, 1 bar, 1 sec
inner side in a roll /outer side in a roll
(non-slip side / slippery side)N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature inner side in a roll /outer side in a roll
(non-slip side / slippery side)
0С - WATERFALL PRO 90-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,3 2,5 3,0
Glossouter side in a roll
(slippery side)% not less
ASTM D2457ISO 2813
85
MD – Machine Direction; TD – Transverse Direction
Main characteristics• resistant to scratching and abrasion• low stable coefficient of friction asymmetric, including over heated surfaces• high hardness• high transparent• high gloss
Application• for wrapping “hard” paper packs of cigarettes, cigarette blocks, tea, marshmallows, sweets, etc.• for film tightening of packs due to shrinkable properties of the film• for tightening packs small and medium sizes
For packing• on the high-speed HFFS packaging machines with a thermotunnel• on the high-speed HFFS packaging machines without a thermotunnel where the film shrink is able due to heating of the weld seal• with hot (heat sealing) seal formed at lower heat sealing temperatures (from 90°C)• “hard” paper packs
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Reeling• Maximum roll diameter: 500 mm• Film width in a roll from 90 to 450 mm• Diameter of paper cores (inside): 76 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent heat sealable shrinkable BOPP film with a very low coefficient of friction for “hard” paper packs packaging on the high-speed machines
TSP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
16 18 20 25
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 14,56 16,38 18,20 22,75
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
150
TD 260
Elongation at breakMD
% not more180
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,05ASTM D1894
ISO 8295GOST 27492
0,15
Shrinkage at 120˚С, 5 minMD
% ±1,0 ASTM D1204ISO 11501
GOST 18616
8,5
TD 6,5
Shrinkage at 130˚С, 15 minMD
% ±2,012,0
TD 12,0
Heat sealing strength at 130˚С, 1 bar, 1 sec
treated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0
Heat sealing temperaturetreated side/
untreated side 0С - WATERFALL PRO 105-140
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,8
Gloss untreated side % not lessASTM D2457
ISO 281385
Surface tension* treated sidemN/n (dyn/
cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction*Measure after treatment with n-heptane
Main characteristics• activated for printing• resistant to scratching and abrasion• low stable coefficient of friction asymmetric, including over heated surfaces• high hardness• high gloss• high transparent
Application• for wrapping “hard” paper packs of cigarettes, cigarette blocks, tea, marshmallows, sweets, etc.• for film tightening of packs due to shrinkable properties of the film• for tightening packs small and medium sizes
For packing• on the high-speed HFFS packaging machines with a thermotunnel• on the high-speed HFFS packaging machines without a thermotunnel where the film shrink is able due to heating of the weld seal• with hot (heat sealing) seal formation• “hard” paper packs
For printing• high-quality rotogravure and flexographic print• with the use of special paints
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is: • for all film types (exept metallized) – 6 months; • for metallized film – 3 months.
Recycling• In the process of printing on activated tobacco films it is recommended not to perform corona treatment.
Reeling• Maximum roll diameter: 500 mm• Film width in a roll from 90 to 450 mm• Diameter of paper cores (inside): 76 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
BOPP film with matte side and glossy treated side for printing and lamination
MP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 20 35
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 13,65 18,20 31,85
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
125
TD 240
Elongation at breakMD
% not more220
TD 80
Kinetic coefficient of friction matte side/ matte side - ±0,15ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 140˚С, 1 bar, 1 sec* matte side/ matte side N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 2,3 2,5
Heat sealing temperature* matte side/ matte side 0С - WATERFALL PRO 130-140
Haze - % not lessASTM D1003
ISO 14782GOST 15875
70
Gloss matte side % not moreASTM D2457
ISO 281312
Surface tension**treated side(glossy side)
mN/n (dyn/cm) not lessASTM D2578
ISO 829638
MD – Machine Direction; TD – Transverse DirectionMatte side – untreated side* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• one side: matte (rough) not activated• the other side: gloss (smooth) activated for reverse printing• high haze, low gloss• low coefficient of friction
Application• as a face film of the package, to make the package matte – “silk” or “paper” kind
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formation, if it is necessary – «overlap»• Flow-Pack and standing packet VFFS • self using in decorative packaging• possibility of application for wrap-around label
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
BOPP film with matte heat sealable side with a low threshold of heat sealability and glossy treated side for printing and lamination
MPLS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 18 20 35
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 13,65 16,38 18,20 31,85
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
125
TD 240
Elongation at breakMD
% not more220
TD 80
Kinetic coefficient of friction matte side/ matte side - ±0,15ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec* matte side/ matte side N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 2,3 2,5
Heat sealing temperature* matte side/ matte side 0С - WATERFALL PRO 110-140
Haze - % not lessASTM D1003
ISO 14782GOST 15875
70
Gloss matte side % not moreASTM D2457
ISO 281312
Surface tension**treated side(glossy side)
mN/n(dyn/cm)
not lessASTM D2578
ISO 829638
MD – Machine Direction; TD – Transverse DirectionMatte side – untreated side* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/m With double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• one side: matte (rough) not activated with a low barrier of friction (from 110˚С)• the other side: gloss (smooth) activated for reverse printing• high haze, low gloss• low coefficient of friction
Application• as a face film of the package, to make the package matte – “silk” or “paper” kind
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formation, if it is necessary – «overlap» on lower temperatures of heat sealable (from 110°С)• Flow-Pack and standing packet VFFS• self using in decorative packaging• application for a wrap-around label
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
BOPP film with matte side with release effect for production of flexible packaging with glue border of coldadhesion and glossy treated side forprinting and lamination
MPR
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 18 20
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 13,65 16,38 18,20
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
125
TD 240
Elongation at breakMD
% not more220
TD 80
Kinetic coefficient of friction matte side/ matte side - ±0,15ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 140˚С, 1 bar, 1 sec matte side/ matte side N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature matte side/ matte side 0С - WATERFALL PRO non-heat sealable
Haze - % not lessASTM D1003
ISO 14782GOST 15875
70
Gloss matte side % not moreASTM D2457
ISO 281312
Surface tensiontreated side(glossy side)
mN/n(dyn/cm)
not lessASTM D2578
ISO 829638
MD – Machine Direction; TD – Transverse DirectionMatte side – untreated sideKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• one side: matte (rough) with a high release effect• the other side: gloss (smooth) activated for reverse printing• high haze, low gloss• low coefficient of friction
Application• as a face film of the package, to make the package matte – “silk” or “paper” kind• for possibility of reopening/reclosing package
For packing• on the HFFS packaging machines• with cold (using cold glue) seal formation• with cold glue for one-and reopening• Flow-Pack
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
BOPP film with matte side and glossy side and double-sided treatment for printing and lamination
MPP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 20 35
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 13,65 18,20 31,85
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
125
TD 240
Elongation at breakMD
% not more220
TD 80
Kinetic coefficient of friction matte side/ matte side - ±0,15ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 140˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Haze - % not lessASTM D1003
ISO 14782GOST 15875
70
Gloss matte side % not moreASTM D2457
ISO 281312
Surface tensiontreated
sidematte side mN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38glossy side
MD – Machine Direction; TD – Transverse DirectionKinetic coefficient of friction after 15 days from the date of producton
Main characteristics• matte side has roughness and diffuses light. When filling the roughness (with water or laquer) the film in these places becomes glossy and transparent. It allows to highlight objects of reverse printing• low coefficient of friction
Application• as a face film of the package, to give the package matte – “silk” or “paper” look• for highlightning objects of reverse printing. When filling the roughness of the matte surface with water or laquer, the film in these places becomes glossy and transparent
For packing• on the high-speed HFFS and VFFS packaging machines• use for decorative packaging
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
BOPP film with matte on both sides and treatment on one side for printing and packaging
MDS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
20 30 35
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 18,20 27,30 31,85
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
120
TD 240
Elongation at breakMD
% not more220
TD 80
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,15ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 140˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,3 2,4 2,5
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 130-140
Haze - % not lessASTM D1003
ISO 14782GOST 15875
70
Gloss untreated side % not moreASTM D2457
ISO 281312
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• matte look from the both sides• slip-antistatic additives
Application• for contact with food• to give the package matte – “silk” or “paper” look• for manual and machine product wrapping (flowers, gifts, textile products etc.)• string heat sealing is possible
For packing• decorative packaging
For printing• high-quality flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
White heat sealable BOPP film with a low coefficient of friction for printing, lamina-tion and packaging
WP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
15 20 25 30 35
Density g/cm3 ±10% 0,96
Weight m2 g/m2 ±5% 14,40 19,20 24,00 28,80 33,60
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
110 120
TD 210 220 230
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,25
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 105-140
Optical transmission - % not moreASTM D1003
ISO 14782GOST 15875
60 50 45 40 35
Gloss untreated side % not lessASTM D2457
ISO 281345
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• all white non-transparent appearance• stable low coefficient of friction• good UV light protection of packaged goods
Application• for the production of flexible packaging for products which require protection from UV-light: ice cream, chocolate, flour, curd products, sweets and etc.• for the production of cut-and-stack bottle labels in the original films form or in lamination
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
White-pearlized cavitated heat sealable BOPP film for printing, lamination and packaging
PP
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
30 35 40 45
Density g/cm3 ±10% 0,72
Weight m2 g/m2 ±5% 21,60 25,20 28,80 32,40
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
70
TD 140
Elongation at breakMD
% not more200
TD 60
Kinetic coefficient of frictionuntreated side /untreated side
-+0,10-0,15
ASTM D1894ISO 8295
GOST 274920,3
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side /untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature*untreated side /untreated side
0С - WATERFALL PRO 105-140
Optical transmission - % not moreASTM D1003
ISO 14782GOST 15875
40 35 30
Gloss untreated side % not lessASTM D2457
ISO 281380
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• protection from UV light• all white appearance with a high level of non-transparency and gloss• lowered density and high yield• film color allows to exclude white paint from printing• color printing on this film is brighter
Application• for packaging of products which require protection from UV-light: ice cream, chocolate, flour, curd products, sweets and etc.
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
White-pearlized cavitated heat sealable with low heat sealability BOPP film for printing, lamination and packaging
PPLS
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
30 35 40 45
Density g/cm3 ±10% 0,72
Weight m2 g/m2 ±5% 21,60 25,20 28,80 32,40
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
70
TD 140
Elongation at breakMD
% not more200
TD 60
Kinetic coefficient of frictionuntreated side /untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,2
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side /untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature*untreated side /untreated side
0С - WATERFALL PRO 80-140
Optical transmission - % not moreASTM D1003
ISO 14782GOST 15875
40 35 30
Gloss untreated side % not lessASTM D2457
ISO 281380
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction* the typical values are indicated, guaranteed only for untreated side** with double-side treatment (if ordered), the activation of the second side (usually the inside of the roll) is not less than 36 mN/mWith double-side processing – strength and range of welding are not applicableKinetic coefficient of friction in 15 days from the date of producton
Main characteristics• low heat sealing temperature• protection from UV light• all white appearance with a high level of non-transparency and gloss• lowered density and high yield• film color allows to exclude white paint from printing• color printing on such film is brighter
Application• for packaging of products which require protection from UV-light: ice cream, chocolate, flour, curd products, sweets and etc.
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formed at lower heat sealing temperatures (from 80°C)• Flow-Pack
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• with the use of solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Transparent BOPP label film
GL
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
30 35 40 45 48 50
Density g/cm3 ±10% 0,91
Weight m2 g/m2 ±5% 27,30 31,90 36,40 40,95 43,68 45,50
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
140
TD 280
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,35
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Haze - % not moreASTM D1003
ISO 14782GOST 15875
2,0
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction
Main characteristics• absence of statics• excellent optical properties• high print adhesion• good slip• high labeling speed
Application• for cut-and-stack bottle labels• for the production of self-adhesive labels at 48-60 μm
For labeling machines• with production speed of 10 000 – 40 000 bottles/hour• with the use of cold and molten glue
For printing• high-quality rotogravure and flexographic print• with the use of special UV-offset and UV-flexo inks with primer coating• direct or riverse print
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
White-pearlized BOPP label film
PL
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
35 38
Density g/cm3 ±10% 0,68
Weight m2 g/m2 ±5% 23,80 25,84
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
80
TD 150
Elongation at breakMD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side /untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,3
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Optical transmission - % not moreASTM D1003
ISO 14782GOST 15875
30
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction
Main characteristics• high print adhesion• high antistatic properties• high level of non-transparency and gloss• good whiteness• preserves label form• high labeling speed
Application• for wrap-around label for PET bottles• for production of self-adhesive labels at 48-60 μm
For labeling machines• with production speed of 10 000 – 40 000 bottles/hour• with the use of cold and molten glue
For printing• high-quality rotogravure and flexographic print• with the use of special UV-offset and UV-flexo inks with primer coating• direct
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
White-pearlized BOPP label film with high gloss
PLG
Properties Unit Limit Method Value
Thickness μm ±5%
WATERFALL PRO
35 38
Density g/cm3 ±10% 0,68
Weight m2 g/m2 ±5% 23,80 25,84
Tensile strengthMD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
75
TD 145
Elongation at breakMD
% not more190
TD 65
Kinetic coefficient of frictionuntreated
side /untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,3
Shrinkage at 120˚С, 5 minMD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Optical transmission - % not moreASTM D1003
ISO 14782GOST 15875
30 25
Gloss treated side % not lessASTM D2457
ISO 281385
Surface tension treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
38
MD – Machine Direction; TD – Transverse Direction
Main characteristics• high level of gloss • high print adhesion• high antistatic properties• high level of non-transparency• preserves label form• high labeling speed
Application• for wrap-around label for PET bottles• for production of self-adhesive labels at 48-60 μm
For labeling machines• with production speed of 10 000 – 40 000 bottles/hour• with the use of cold and molten glue
For printing• high-quality rotogravure and flexographic print• with the use of special UV-offset and UV-flexo inks with primer coating• direct
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
TreatmentThe guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months;• for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
RecyclingIn the process of printing and lamination it is recommended to perform corona treatment.
Reeling• Maximum roll diameter: 800 mm• Film width in a roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on white-pearlized cavitated base BOPP label film
PLMM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
35 38 47
Density* g/cm3 ±10% 0,70
Weight m2* g/m2 ±5% 24,50 26,60 32,90
Tensile strength*MD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
80
TD 150
Elongation at break*MD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,35
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec* - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density treated side OD not less WATERFALL PRO 1,8
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• extra smooth surface and high gloss of metallized side• excellent adhesion of alluminium layer• lowered density and high yield• high level of transparency• good whiteness
Application• for wrap-around label for bottles• for production of self-adhesive labels
For labeling machines• with production speed of 10 000 – 40 000 bottles/hour• with the use of cold and molten glue
For printing• high-quality rotogravure and flexographic print• with the use of special UV-offset and UV-flexo inks with primer coating• direct
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on transparent base heat seal-able BOPP film for printing, lamination and packaging
GMM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
12 15 18 20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 * g/m2 ±5% 10,92 13,65 16,38 18,20 22,75 27,30 31,85 36,40
Tensile strength*MD N/mm²
(MPa)not less ASTM D882
ISO 527GOST 14236
130 140
TD 230 250
Elongation at break*MD
% not more220 200
TD 80 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,3
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 3 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 2,2 2,3 2,5 2,8
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 105-140
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density - OD not less WATERFALL PRO 1,8
WVTR-water vapour transmission rate at 38°C, 90% rel. humidity, 24 h g/m²/24h not more ASTM F1249 1,0
OTR-oxygen transmission rate at 23°С, 0% rel. humidity, 24 h sm³/m²/24h not more ASTM D3985 100
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• long-term activation• excellent adhesion of alluminium cover• excellent optical properties• excellent barrier properties• stable regular coefficient of friction
Application• for improvement of barrier properties of package• for wrap-around label for bottles
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack
For lamination• with other films and materials in duplex, triplex• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• using solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on transparent base non-heat sealable BOPP film for printing,lamination and decorative packaging
GMPM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2* g/m2 ±5% 18,20 22,75 27,30 31,85 36,40
Tensile strength*MD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
140
TD 250
Elongation at break*MD
% not more200
TD 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,35
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec* - N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
non-heat sealable
Heat sealing temperature - 0С - WATERFALL PRO non-heat sealable
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density - OD not less WATERFALL PRO 1,8
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• long-term activation• excellent adhesion of alluminium cover• excellent optical properties• regular barrier properties• high coefficient of friction
Application• for decorative packaging/wrapping• for packet machines• for packaging tape production• for wrap-around label for bottles
For packing• in cases, when heat sealing is not required• with hot (heat sealing) and cold (using cold glue) seal formation• manual application in decorative packaging
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• using solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on transparent base BOPP film for printing, lamination and packaging
GMBM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
18 20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 * g/m2 ±5% 16,38 18,20 22,75 27,30 31,85 36,40
Tensile strength*MD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
130 140
TD 230 250
Elongation at break*MD
% not more220 200
TD 80 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,3
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 3 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 3,0 3,2
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 105-140
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density - OD not less WATERFALL PRO 2,3
WVTR-water vapour transmission rate at 38°C, 90% rel. humidity, 24 h g/m²/24h not more ASTM F1249 1,0
OTR-oxygen transmission rate at 23°С, 0% rel. humidity, 24 h sm³/m²/24h not more ASTM D3985 50
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• excellent barrier properties• long-term activation• excellent adhesion of alluminium cover• excellent optical properties• stable regular coefficient of friction
Application• for packaging of products which require high barrier properties: bisquits, chips, waffles and etc.• for extension of products storage period
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack
For lamination• with other films and materials• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• using solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on transparent base heat sealable with low heat sealing threshold BOPP film for printing, lamination and packaging
GMLSM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
15 20 25 30 35 40
Density g/cm3 ±10% 0,91
Weight m2 * g/m2 ±5% 13,65 18,20 22,75 27,30 31,85 36,40
Tensile strength*MD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
130 140
TD 230 250
Elongation at break*MD
% not more220 200
TD 80 70
Kinetic coefficient of frictionuntreated side/untreated side
- ±0,10ASTM D1894
ISO 8295GOST 27492
0,3
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
5 4
TD 3 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,0 2,3 2,5 2,8
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 80-140
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density - OD not less WATERFALL PRO 1,8
WVTR-water vapour transmission rate at 38°C, 90% rel. humidity, 24 h g/m²/24h not more ASTM F1249 1,0
OTR-oxygen transmission rate at 23°С, 0% rel. humidity, 24 h sm³/m²/24h not more ASTM D3985 100
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• long-term activation• low heat sealing temperature• excellent adhesion of alluminium cover• excellent optical properties• excellent barrier properties• stable regular coefficient of friction
Application• for improvement of package’s barrier properties• for decreasing temperature of heat sealing• for increasing speed of heat sealing
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) seal formed at lower heat sealing temperatures (from 80°C)• Flow-Pack
For lamination• with other films and materials in duplex, triplex• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• using solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm
Description
Attention! Information specified in this document is for reference only; it contains averaged technical characteristics of Waterfall Pro LLC products based on results of laboratory tests performed in Waterfall Pro LLC standard operation conditions. Waterfall Pro LLC gives no representations and/or warranties and is expressly relived from any liability for infringement of any third parties’ intellectual property rights arising from processing of Waterfall Pro LLC products. Testing of Waterfall Pro LLC products in order to determine their suitability in terms of meeting specific objectives of a person intending to purchase Waterfall Pro LLC products is the sole responsibility of such a person who shall be responsible for any consequences related to processing and use of Waterfall Pro LLC products.This document does not constitute a quotation and its provision to any person shall not create any rights and duties on the part of Waterfall Pro LLC.
2a Shapkina Str., Shakhty, Rostov region, Russia, 346510, tel.: +7 (8636) 20-00-30, e-mail: [email protected] floor, Suite 32, Federation-East Tower, MIBC Moscow-City, 12, Presnenskaya Embankment, Moscow, 123317, tel.: +7 (499) 643-83-31, e-mail: [email protected]
WWW.WATERFALL-PRO.RU
Metallized on cavitated white-pearlized layer heat sealable BOPP film for printing and lamination
PMM
Properties Unit Limit Method Value
Thickness* μm ±5%
WATERFALL PRO
30 35 40
Density* g/cm3 ±10% 0,70
Weight m2* g/m2 ±5% 21,00 24,50 28,00
Tensile strength*MD
N/mm² (MPa) not less ASTM D882ISO 527
GOST 14236
70
TD 140
Elongation at break*MD
% not more200
TD 60
Kinetic coefficient of frictionuntreated side/untreated side
-+0,10-0,15
ASTM D1894ISO 8295
GOST 274920,3
Shrinkage at 120˚С, 5 min*MD
% not moreASTM D1204
ISO 11501GOST 18616
4
TD 2
Heat sealing strength at 130˚С, 1 bar, 1 sec*
untreated side/untreated side
N/15 mm not less
ASTM F88/F88MD882
ISO 527GOST 27319
2,5
Heat sealing temperature*untreated side/untreated side
0С - WATERFALL PRO 105-140
Surface tension** treated sidemN/n
(dyn/cm)not less
ASTM D2578ISO 8296
36
Optical density - OD not less WATERFALL PRO 1,8
WVTR-water vapour transmission rate at 38°C, 90% rel. humidity, 24 h g/m²/24h not more ASTM F1249 1,5
OTR-oxygen transmission rate at 23°С, 0% rel. humidity, 24 h sm³/m²/24h not more ASTM D3985 150
MD – Machine Direction; TD – Transverse Direction* performance is measured on BOPP film – base for metallization** guaranteed conservation period of activation on metallized side of film is 3 months from production date specified on identification roll tag
Main characteristics• long-term activation• activation on both sides on demand• excellent adhesion of alluminium cover• excellent optical properties• excellent barrier properties• high coefficient of friction• lowered density and high yield
Application• for packaging of products which require high barrier properties and protection from UV-light: ice-cream, chocolate and etc.• for extension of products storage period
For packing• on the high-speed HFFS and VFFS packaging machines• with hot (heat sealing) and cold (using cold glue) seal formation• Flow-Pack
For lamination• with other films and materials in duplex, triplex• with method of the solvent or nonsolvent (extrusion) lamination
For printing• high-quality rotogravure and flexographic print• using solvent paint
Storage• Films should be stored on the pallets in a closed dry place and should not be exposed to direct sunlight, at a safe distance of not less than 1 m from heating devices or anything that can cause damage the package.• The film should be kept in workplace not less than 48 hours before being used.• Guaranteed storage period – 6 months from production date.
Treatment The guaranteed period for maintaining the minimum permissible level of surface tension on the activated film surface from the date of manufacture, subject to proper storage conditions, is:• for all film types (exept metallized) – 6 months; • for metallized film – 3 months.In the interests of minimizing the deterioration of surface dressing level, it is recommended to store the film at a temperature of no higher than 30°C and use it in a short time.
Recycling• It’s recommended to use primer when printing on metallized surface.
Reeling• Maximum roll diameter: 800 mm• Film width in roll from 290 to 2000 mm• Diameter of paper cores (inside): 76, 152 mm