Download - BHEL JHANSI
1
BUNDELKHAND INSTITUTE OF ENGINEERING AND TECHNOLOGY JHANSI
BY :NAME
INDUSTRIAL TRAINING SEMINAR
INTRODUCTION TO CNC MACHINEFrom
BHEL JHANSI
2
INDEXIntroduction of BHEL
Products
History
Introduction to CNC
Need of CNC
Types of CNC Machine
Block Diagram of CNC Machines
Working of CNC Machine
Elements of CNC
Input devices
Machine control unit
Driving System
Feedback System
Display Unit
CNC Programming Basics
Advantages
Challenges
Conclusions
BHEL
2
BHEL is India's largest engineering and manufacturing Enterprise.
Established in 1956. Got 'Maharatna' status by the Government of India on 1
February 2013. More than 150 project sites across India and abroad. The company has added more than 1,24,000 MW to the
country's installed power generating capacity so far.
4
PRODUCTS
Locomotive Plant Boilers Auxiliaries Plant. Transformer. Power electronics. Electrical machines. Insulator Plant Oil field equipment.
5
HISTORY
The first NC machines were built in the 1940s and 1950s by Prof. John T Parson.
US Air Force teamed up with MIT to develop a programmable milling machine (1949).
CNC machine came into existence after evolution of computer around 1980.
Modern CNC Machine are improving further as the technology is changing with a variety of functions according to applications.
6
INTRODUCTION
Numerical control is a method of automatically operating a manufacturing machine based on a code of letters, numbers, and special characters.
The numerical data required to produce a part is provided to a machine in the form of a program, called part program or CNC program.
The program is translated into the appropriate electrical signals for input to motors that run the machine.
7
NEED OF CNC
Increase production rate. Stabilize manufacturing costs. Highly accurate over traditional machines. More operations can be performed with each
setup Repeatability, reduced scrap loss, and high production rates.
8
TYPES OF CNC MACHINES
There are many different types of CNC Machines used in industry, Such as:
Mills and Machining Centers Lathes and Turning Centers. Drilling Machines Wire cut Machines. Flame and Laser-Cutting Machines
9
BLOCK DIAGRAM
10
WORKING OF CNC
All computer controlled machines are able to accurately and repeatedly control motion in various directions. Each of these directions of motion is called an axis. Depending on the machine type there are commonly two to five axes.
11
Open loop and Closed loop controls
12
Elements of CNC Machine
Input Device Machine Control Unit Machine Tool Driving System Feedback Devices Display Unit
13
Input Devices
Floppy Disk Drive. USB Flash Drive. Serial communication.
14
Machine Control Unit Data Processing Unit On receiving a part programme, the DPU firstly interprets and encodes the
part programme into internal machine codes.
Control Loop Unit Data from the DPU are converted into electrical signals in the CLU to control
the driving system to perform the required motions.
15
Driving System This system usually uses electric motors although hydraulic motors are
sometimes used for large machine tools. DC servo motor The principle of operation is based on the rotation of an armature winding
in a permanently energized magnetic field. Stepper Motor A stepper motor is a device that converts the electrical pulses into discrete
mechanical rotational motions of the motor shaft
16
FEEDBACK DEVICES
Positional Feed Back Devices
A linear transducer is a device mounted on the machine table to
measure the actual displacement of the slide.
Velocity Feedback Device
The actual speed of the motor can be measured in terms of voltage
generated from a tachometer mounted at the end of the motor shaft.
17
Display UnitThe Display Unit serves as an interactive device between the machine and the operator. Operator Control PanelTo facilitate two-way communication between the user, CNC system and the machine tool. Video Display Unit (VDU). Keyboard. Machine Control Panel (MCP)It is the direct interface between operator and the NC system, enabling the operation of the machine through the CNC system.
18
CNC Programming Basics
CNC instructions are called part program commands.
When running, a part program is interpreted one command line at a time until all
lines are completed.
Commands, which are also referred to as blocks, are made up of words which
each begin with a letter address and end with a numerical value.
19
Advantages Easier to program; Easy storage of existing programs; Easy to change a program Avoids human errors CNC machines are safe to operate Complex geometry is produced as cheaply as simple ones Usually generates closer tolerances than manual machines
20
Challenges
Costly setup, skilled operators Computers, programming knowledge required Maintenance is difficult
21
Conclusion The advantage of a CNC system are that the operation of a conventional
machine is removed and the part production is made automatic. It reduces the labor work and hence highly efficient in the manufacturing
process. BHEL generally uses CNC machines to achieve its manufacturing targets. For
manufacturing works of large scale it is very difficult to work with manual machines as they are time consuming. CNC machines have their wide scope because they are easy to handle, the work becomes easier and jobs are done with perfection.
22
THANK YOU