Assembly ManualSunshelter 12 x 16 ft.Exact dimension of the roof, corner-to-corner: 143.7 x 191.3 inchMin. dimension required for the base: 145.3 x 192.9 inch
Sojag code: 500-5156362
UPC code: 772830156362
Guide d’assemblageAbri-soleil 3,66 x 4,88 m
Dimension exacte du toit, coin à coin : 365 x 486 cmDimension min. requise pour la base : 369 x 490 cm
Code Sojag : 500-5156362
Code CUP : 772830156362
© Sojag inc. 2015
2© Sojag inc. 2015
HARDWARE KIT TROUSSE DE QUINCAILLERIENOTE:Parts not shown to actual size and not to scale.
NOTE :Le matériel n’est pas représenté à l’échelle.
Item Description Qty
M Allen Key 1
M1 Allen Key 1
N Screw M6X12 24
O Screw M6X16 82
P Screw M6X35 and Nut 4
R Screw St5X16 16
T Hook 128
Pièce Description Qté
M Clé hexagonale 1
M1 Clé hexagonale 1
N Vis M6X12 24
O Vis M6X16 82
P Vis M6X16 et écrou 4
R Vis St5X16 16
T Crochet 128
T X128
R X16O X82
N X24M1 X1M X1
P X4
IMPORTANTRead the owner’s manual and make sure all parts
are included PRIOR to the start of assembly.
IMPORTANTLire le guide de l’utilisateur AVANT
de débuter l’assemblage du produit.
3© Sojag inc. 2015
Item Description Qty
A Column 4
A1 Column 2
B Track 2
B1 Track 2
C Track 2
C1 Track 2
D Corner Roof Bar 4
D1 Corner Roof Bar 4
E Roof Bar 8
G Roof Connector 2
G1 Central Roof Connector 1
H Corner Connector 4
Pièce Description Qté
A Colonne 4
A1 Colonne 2
B Rail 2
B1 Rail 2
C Rail 2
C1 Rail 2
D Barre de toit de coin 4
D1 Barre de toit de coin 4
E Barre de toit 8
G Connecteur de toit 2
G1 Connecteur de toit central 1
H Connecteur de coin 4
A1 X2
A X4
D
D1
X4
X4
E X8
G X2H X4G1 X1
B X2
B1 X2
C X2
C1 X2
PARTS LIST LISTE DES PIÈCESNOTE:Parts not shown to actual size and not to scale.
NOTE :Le matériel n’est pas représenté à l’échelle.
4© Sojag inc. 2015
Item Description Qty
I Solidifying Bar 8
J Solidifying Bar 4
K Base 6
L Union Track 2
W Canopy 1
X Curtain 4
Y Mosquito Net 4
Y1 Band 4
Z Roof Central Bar 1
Pièce Description Qté
I Barre de renforcement 8
J Barre de renforcement 4
K Base 6
L Rail d’union 2
W Toit 1
X Rideau 4
Y Moustiquaire 4
Y1 Ganse 4
Z Barre centrale de toit 1
I X8 J X4
K X6
X X4
Y X4
Z X1Y1 X4
W X1
L X2
5
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Step 11.1 Install the column (A) on the base (K)
using the screws (O).
Repeat for all remaining columns (A and A1).
Étape 11.1 Installer une colonne (A) sur une base (K) en
utilisant les vis (O).
Répéter pour les colonnes (A et A1) restantes.
A/A1
K
A/A1
O
X6
X6
K
K X6 O X18
A X4
A1 X2
6
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Step 22.1 Insert 9 hooks (T) into each track of the parts
(B and B1). Refer to the side view draw.
2.2 Slide the union track (L) into the track (B and B1)
and attach with the screws (O).
Repeat for all remaining tracks (B and B1).
2.3 Insert 7 hooks (T) into each track of the parts
(C and C1). Refer to the side view draw.
2.4 Slide the track (C) into the track (C1).
2.5 Attach the track (C) to the track (C1)
using the screws (O).
Repeat for all remaining tracks (C and C1).
Étape 22.1 Insérer neuf crochets (T) dans chaque rail de chaque
pièce (B et B1). Se referer à l’image de vue
de profil.
2.2 Insérer le rail d’union (L) dans le rail (B et B1)
et attacher avec les vis (O).
Répéter pour les rails restants (B et B1).
2.3 Insérer sept crochets (T) dans chaque rail de chaque
pièce (C et C1). Se referer à l’image de vue
de profil.
2.4 Insérer le bout du rail (C) au bout du rail (C1).
2.5 Attacher les rails (C et C1) ensemble en
utilisant les vis (O).
Répéter pour les rails restants (C et C1).
T O X32X128L X2
B X2
B1 X2
C X2
C1 X2
7© Sojag inc. 2015
X2
X2
B1
B1
B1
C1
C1
C1
B
B L
B
C
C
C
1
11
33
T
T
Side view
Vue de profil
TX9
X9
3
T
T X7
X7
O
O
C1 C
BL2
2 2
8
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
IMPORTANT:Always install the shelter on a level platform, wood or concrete.
IMPORTANT :Toujours installer la structure sur une surface de niveau.
Step 33.1 Install the tracks (B/L/B1, C/C1) between
two columns (A) using the screws (N) on the
outside of the tracks.
Repeat for all remaining tracks (B/L/B1,
C/C1).
Étape 33.1 Installer les rails (B/L/B1, C /C1) entre deux
colonnes (A) en utilisant les vis (N) à l’avant des rails.
Répéter pour les rails restants (B /L/ B1, C /C1).
CAUTION:Three people are required for this step.
AVERTISSEMENT :Trois personnes sont requises pour cette étape.
N X16
9© Sojag inc. 2015
AA A
A
BL
X4
N
B L
C
C
C1
C1 B1
B1
A
1
1
1
1
1
10
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Step 44.1 Attach two solidifying bars (I) on each corner
of the structure using the screws (O) as illustrated.
4.2 Attach the solidifying bars (J) into each corner
of the structure using the screws (O).
Étape 44.1 Attacher deux barres de renforcement (I) dans
chaque coin de la structure en utilisant les vis (O)
tel qu’illustré.
4.2 Attacher les barres de renforcement (J) à l’intérieur de
chaque coin de la structure en utilisant les vis (O).
I X8
J X4
O X32
11© Sojag inc. 2015
X4
X4
X4
I
IO
OO
O
O
J
OO
I
I
AA
A
1
1
1
1
12
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Step 55.1 Fix a corner connector (H) on each corner
of the structure using the screws (R).
Étape 55.1 Attacher un connecteurs de coin (H) à l’extérieur de
chaque coin de la structure en utilisant les vis (R).
R X16H X4
13© Sojag inc. 2015
X4
H
R
1
1
1
1
1
14
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Étape 66.1 Glisser le connecteur de toit central (G1) jusqu’au centre
de la barre centrale de toit (Z) tel qu’illustré.
6.2 Glisser les connecteurs de toit (G) à chaque extrémité de
la barre centrale de toit (Z) tel qu’illustré.
6.3 Glisser la barre de toit (D1) dans la barre de toit (D) et
attacher avec la vis et l’écrou (P).
Répéter pour chaque barre de toit (D et D1) restante.
Step 66.1 Slide the central roof connector (G1) up to the
centre of the roof central bar (Z) as illustrated.
6.2 Slide one roof connector (G) on each end of the
roof central bar (Z) as illustrted.
6.3 Slide the roof bar (D1) into the roof bar (D) and
attach with a screw and nut (P).
Repeat for remaining roof bars (D and D1).
Z X1G X2
G1 X1
D X4 D1 X4P X4
15© Sojag inc. 2015
G
G
G
G
G
G
DP
Z
Z
Z
G1
G1
G1
D1X4
16
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Étape 77.1 Installer une barre de toit (D/D1) dans chaque coin de la
structure en glissant une extrémité dans le connecteur
de coin (H) et l’autre extrémité aux connecteurs de toit (G).
7.2 Installer les barres de toit (E) en glissant une extrémité
dans le connecteur de toit (G et G1) et attacher l’autre
extrémité à la structure utilisant une vis (O) tel qu’illustré.
Step 77.1 Install a roof bar (D/D1) on each corner of the
unit by sliding one extremity into the corner
connectors (H) and the other extremity into
the roof connectors (G) as illustrated.
7.2 Attach the roof bars (E) to the structure by sliding
one extremity into the roof connectors (G and G1)
and attach the other extremity to the structure
using a screw (O) as illustrated.
O X8
E X8
17© Sojag inc. 2015
DD1
E
D1D
D D1
E
DD1
EEE
1
1
1
1
12 2
2
222
3
D1H
X4
E
G1G
Z
X4
X2
E
O
X4
2
2
EE
ZD
DE
E
E
3
3
18
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Étape 88.1 Installer les colonnes (A1) au centre de chaque rail
d’union (L) en utilisant les vis (N) tel qu’illustré.
Step 88.1 Install the columns (A1) on the middle of the union
track (L) using the screws (N) as illustrated.
N X8
19© Sojag inc. 2015
A1
A1
X2A1
L
L
N
20
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Étape 99.1 Placer le toit (W) sur le dessus de la structure.
Step 99.1 Place the canopy (W) on top of the structure.
W X1
21© Sojag inc. 2015
W
22
Parts required for this step / Pièces requises pour cette étape :
ASSEMBLY ASSEMBLAGE
© Sojag inc. 2015
Étape 1010.1 Installer les moustiquaires (Y) sur les rails intérieurs en
insérant les crochets (T), les uns après les autres,
dans chacun des oeillets. Répéter cette étape pour
les quatre moustiquaires (Y).
10.2 Installer les rideaux (X) sur les rails extérieurs en insérant
les crochets (T), les uns après les autres, dans chacun
des oeillets. Répéter cette étape pour les quatre
rideaux (X).
Step 1010.1 Install the mosquito netting (Y) along the inside
tracks by inserting the hooks (T) one at a time
into the eyelets found along the top border of
the netting. Repeat for all four netting panels (Y).
10.2 Install the curtain (X) along the outside tracks by
inserting the hooks (T) one at a time into the
eyelets found along the top border of the curtain.
Repeat for all four curtain panels (X).
NOTE:The netting and the curtain should be installed starting in the middle of the 12 feet side of the unit, and finish the installation in the middle of the next side of the unit. The zippers to close the netting will therefore meet in the center of the each side of the sun shelter.
NOTE :Les moustiquaires et les rideaux doivent être installées en commençant par le milieu d’un côté de 12 pi de l’abri et en se terminant au milieu du côté adjacent. Les fermetures éclair vont alors se rencontrer au centre de chacun des côtés de l’abri.
X X4
Y X4
Y1 X4
23© Sojag inc. 2015
YY
Y1
X
X
Made in CHINA / Fabriqué en CHINE / Hecho en CHINA
Prin
ted
in C
hina
/ Im
prim
é en
Chi
ne
www.sojag.ca