-
POWERFLOPOWERFLOPOWERFLOPOWERFLOPOWERFLOBRONZEBRONZEBRONZEBRONZEBRONZE
SAFETY & RELIEFSAFETY & RELIEFSAFETY & RELIEFSAFETY & RELIEFSAFETY & RELIEF
VVVVVALALALALALVESVESVESVESVES
Manufactured toManufactured toManufactured toManufactured toManufactured toAS 1271AS 1271AS 1271AS 1271AS 1271
-
- 2 -
Austral-Powerflo Solutions (APS) has earned an Australia-wide reputation for engineering excellence.Our manufacturing facility is devoted to the manufacture of safety and relief valves, to therequirements of AS1271 and AS3653 for use on Boilers and Unfired Pressure Vessels.
Safety and Relief Valves for Steam, Gas, Vapour & Liquid Service
Protection of personnel and equipment is theparamount concern in the selection of safety reliefvalves for plant operating systems. Only the mostreliable safety valves should be considered for such acrucial role. POWERFLO valves have consistentlybeen recognized as leaders in the pressure relief valvefield since their introduction over 100 years ago.
Our leadership in design, manufacture and productservices is founded on our reputation for unrelentingdedication to product innovation and improvement. Acontinuous program for keeping abreast of constantlychanging requirements of the valve market and aconcentrated research and development effort assurestrong support for customer needs.
APS personnel are technically trained and availableto provide guidance in sizing and selection of theappropriate valves for specific applications.
Type 1543-3 SeriesConventional
APSSafety Relief Valves - to AS1271 - Class A
Our comprehensive range of safety relief valves, representingover 100 years of valve manufacturing experience, aremanufactured, tested and inspected under the controlsestablished by a Bureau Veritas Certification approved qualitymanagement system that conforms with ISO 9001:2008. BureauVeritas Certification under Certificate No. 11000045.
ASME CodePOWERFLO Safety Valves have been flow tested inaccordance with ASME Code rules to establish ratedcapacities. Capacities specified in this catalogue have beencertified by the National Board of Boiler and Pressure VesselInspectors and are listed in the National Board publicationPressure Relieving Device Certifications.
QualityEach valve is manufactured in accordance with establisheddesign criteria and is tested for functional performance,thereby ensuring that it will provide long and reliableservice.
AS/NZS ISO 9001:2008AS/NZS ISO 9001:2008AS/NZS ISO 9001:2008AS/NZS ISO 9001:2008AS/NZS ISO 9001:2008CERCERCERCERCERTIFICATIFICATIFICATIFICATIFICATE No. 11000045TE No. 11000045TE No. 11000045TE No. 11000045TE No. 11000045
-
- 3 -
Accurate set pressure
Accurate closing pressure
Accurate lift measurement
Detect defects & malfunction
Avoid seat damage
Simulate actual operation
Safety Relief Valves
You may not realise that thereis much more to achievingsafety than just sending yoursafety and relief valves to anyrepairer.
Austral-PowerAustral-PowerAustral-PowerAustral-PowerAustral-Powerflofloflofloflos High Capacitys High Capacitys High Capacitys High Capacitys High CapacityTTTTTest Rig is designed to simulateest Rig is designed to simulateest Rig is designed to simulateest Rig is designed to simulateest Rig is designed to simulateconditionsconditionsconditionsconditionsconditions close to those occurringin the process. Other methods ofsetting and testing reliefvalves, such as nitrogenbottles or air compressor andreceiver, do not achieve thesame level of accuracy andrepeatability. These methodsdo not simulate a pop actionwith full lift and, in manycases, only achieve the pointof simmer, and may damagedamagedamagedamagedamage
RELIEF VALVE & CONTROL VALVE TESTING
OBJECTIVEOBJECTIVEOBJECTIVEOBJECTIVEOBJECTIVE
Using incorrect setting methods means your SafetyUsing incorrect setting methods means your SafetyUsing incorrect setting methods means your SafetyUsing incorrect setting methods means your SafetyUsing incorrect setting methods means your Safetyvalves may not relieve at the correct pressure!valves may not relieve at the correct pressure!valves may not relieve at the correct pressure!valves may not relieve at the correct pressure!valves may not relieve at the correct pressure!
AUSTRAL-POWERFLOs High Capacity Test Rig is your bestguarantee that relief valves will relieve at set point and reseat
correctly, without leakage.
How Do You Know Your Repairer is Competent?
TEST METHOD
Not Possible
Not Possible
Not Possible
APSs High Nitrogen Hand HesitationCapacity Bottle Pump Gauge /Test Rig Bubble Jar
your valve. Leaking Leaking Leaking Leaking Leaking valves mean energy lossesenergy lossesenergy lossesenergy lossesenergy losses and pollutionpollutionpollutionpollutionpollution, increasing your maintenance ofancillary equipment, reducing up-time, which costs you moneycosts you moneycosts you moneycosts you moneycosts you money!
The following Table shows results of an evaluation of various commonly used test methods. Whatmethod does your repairer use?
-
- 4 -
CodesCodesCodesCodesCodes AS1271 Class A AS1271 Class A AS1271 Class A
1551 Series S1541-3 Series
POWERFLO Safety-Relief Valves - for
1479 Series
Orifice SizesOrifice SizesOrifice SizesOrifice SizesOrifice Sizes 15NB 20NB 15NB 20NB Six Sizes: D through J
Orifice ArOrifice ArOrifice ArOrifice ArOrifice Areaeaeaeaea 126.7mm2 181.8mm2 126.7mm2 181.8mm2 71 through 830mm2
Options:Options:Options:Options:Options: SPL - Screwed Cap for Liquid SPL - Screwed Cap for SPL - Screwed Cap for
Service Vapour and Gas Service, for Vapour and Gas service,
only includes Adjusting Ring includes Adjusting Ring
No Adjusting Ring fitted CP - Chrome Plating Optional 1541 Available with
of valve Bronze base and seat, limited to
Note: 2050 kPag set pressure
Use Type 1551-SPL valve for
Vapour and Gas Service where
screwed cap is required.
StandarStandarStandarStandarStandard Materials:d Materials:d Materials:d Materials:d Materials:
Base/SeatBase/SeatBase/SeatBase/SeatBase/Seat Forged Brass Forged Brass 316SS
BonnetBonnetBonnetBonnetBonnet Bronze Bronze Bronze
DiscDiscDiscDiscDisc Forged Brass Forged Brass 316SS
SpindleSpindleSpindleSpindleSpindle High Tensile Brass High Tensile Brass 316SS
SpringSpringSpringSpringSpring SS SS Carbon or SS
FeaturFeaturFeaturFeaturFeatures:es:es:es:es:
Bro
nze
Scr
ewed
Val
ves
Flat Disc Design with full
guiding, suitable for broad
range of applications.
Medium capacity, full lift
valve, having positive sealing,
sharp clean opening and ease
of adjustment.
Wing Guided Disc
Available only in Brass
Wing Guided Disc
Available only in Brass
Large Capacity
Lifting Lever for Hot Water
Service, above 60C.
Inlet SizesInlet SizesInlet SizesInlet SizesInlet Sizes 15 and 20mm BSP/NPT 15 and 20mm BSP/NPT 20 to 65mm BSP/NPT
Outlet SizesOutlet SizesOutlet SizesOutlet SizesOutlet Sizes 25BSP/NPT 25mm BSP/NPT 20 to 65mm BSP/NPT
TTTTTemperaturemperaturemperaturemperaturemperature Rangee Rangee Rangee Rangee Range -28C to 230C -28C to 230C -28C to 230CSet PrSet PrSet PrSet PrSet Pressuressuressuressuressure Rangee Rangee Rangee Rangee Range 70 kPag to 2050 kPag 70 kPag to 2050 kPag 35 kPag to 2400 kPag
SerSerSerSerService:vice:vice:vice:vice: Liquids, Water, Oil Steam, Air, Gas Liquids, Water, Oil, Steam, Air
and Gas
-
- 5 -
Gas, Vapour and Liquid Service
AS1271 Class A
Six Sizes: D through J
71 through 830mm2
SPL - Screwed Cap for Vapour and
Gas service, includes Adjusting
Ring.
Optional 1543 available with Bronze
Base and Seat, limited to 2050 kPag
set pressure
CP - Chrome-plating of valve
Soft seat insert in bronze disc only
316SS
Bronze
316SS
316SS
Carbon or SS
S1543-3 Series
Bro
nze
Fla
nged
Val
ves
Flat Disc Design with full guiding,
suitable for broad range of applications.
High capacity, full lift valve, having
positive sealing, sharp clean opening
and ease of adjustment.
F1541-3 Series F1543-3 Series
AS1271 Class A
Six Sizes: D through J
71 through 830mm2
Standard Materials:
Base Seat 316SS
Bonnet Bronze
Disc 316SS
Spindle 316SS
Spring Carbon or SS
Options:
Flanges to AS2129
Flanges to ANSI 150RF
ANSI 300RF
SPL - Screwed Cap for Vapour and
Gas service, includes Adjusting Ring.
Optional 1541 available with Bronze
base and seat, limited to 2050 kPag
set pressure
316SS
Bronze
316SS
316SS
Carbon or SS
Six Sizes: D through J
71 through 830mm2
15 to 50mm
20 to 65mm
-28C to 230C35 kPag to 2400 kPag
AS1271 Class A
20 to 65mm
20 to 65mm
-28C to 230C35 kPag to 2400 kPag
15 to 50mm BSP/NPT
20 to 65mm BSP/NPT
-28C to 230C35 kPag to 2400 kPag
Options:
Flanges to AS2129
Flanges to ANSI 150RF
ANSI 300RF
SPL - Screwed Cap for Vapour
and Gas service, includes Adjusting
Ring.
Optional 1543 available with Bronze
Base and Seat, limited to 2050 kPag
set pressure
CP - Chrome-plating of valve
Soft seat insert in bronze disc only
Flat Disc Design with full guiding,
suitable for broad range of applications.
Medium capacity, full lift valve, having
positive sealing, sharp clean opening
and ease of adjustment.
Flat Disc Design with full guiding,
suitable for broad range of applications.
High capacity, full lift valve, having
positive sealing, sharp clean opening
and ease of adjustment.
Liquids, Water, Oil, Steam, Air
and Gas
Liquids, Water, Oil, Steam, Air
and Gas
Liquids, Water, Oil, Steam, Air
and Gas
-
- 6 -
POWERFLO Safety and Relief Valves
Fig. 1479 and 1551 Medium Capacity for air, steam, gas or liquidThis is a medium capacity low priced valve meeting the AS1271 requirements, providing the optimum product to meet theseverest demands.
Important features of the valve are its positive sealing, sharp, clean opening and ease of adjustment.
The POWERFLO 1479 and 1551 Bronze Safety and Safety Relief Valves are offered in 15 and 20mm sizes for steam, air orliquid service in a variety of combinations for pressures up to 2050kPa. They are available with screwed bases, with brassbase and disc as standard.
Designed specifically for air, steam, gas and liquid service, POWERFLO Valves will meet all the varied needs of Industrytoday. POWERFLO Valves are engineered and manufactured to meet the most exacting requirements of industry for positiveand dependable operation.
Users of POWERFLO Safety Relief Valves benefit by the accumulated experience of more than 100 years of development,engineering, manufacturing and field experience in safety and relief valve design for the protection of all types of pressurevessels and systems.
The purpose of a safety valve or relief valve is protection of personnel, plant and production. To perform this basic function,a safety relief valve must be designed to open automatically at a predetermined set pressure, must be sized to provide fullpressure relief of the pressure system on which it is installed, must provide positive closing and tightness after operation. ThePOWERFLO Safety Valve will provide this basic function.
POWERFLO Safety Valves are engineered to make use of the characteristics of air, steam or gases which have a powerfulexpansion force when liberated. This force, and kinetic energy of the media flowing from the valve orifice, is fully utilised togive the definite pop action associated with POWERFLO Safety Valves.
The full advantages of these two factors, coupled with the carefully developed contours of the POWERFLO Safety Valvehuddle chamber, increase the valve lift and therefore increase the capacity of the valve. Different media, with varying specificgravities can cause the valve to perform in different ways. To allow for this, the POWERFLO 1541/1543 Safety Valve isdesigned with two performance adjusting rings. The upper adjusting ring controls the blowdown by redirecting the flow streamthrough 1800 through a secondary orifice, the size of which is adjusted to achieve maximum valve lift.
POWERFLO Safety VPOWERFLO Safety VPOWERFLO Safety VPOWERFLO Safety VPOWERFLO Safety Valves aralves aralves aralves aralves are manufacture manufacture manufacture manufacture manufactured by Austral-Powered by Austral-Powered by Austral-Powered by Austral-Powered by Austral-Powerflo Solutions to Australian Standarflo Solutions to Australian Standarflo Solutions to Australian Standarflo Solutions to Australian Standarflo Solutions to Australian Standards.ds.ds.ds.ds.
Fig. 1541-3 - Medium Capacity for air, steam and gasThe POWERFLO 1541 Bronze Safety Relief Valve is a medium capacity full lift valve meeting AS1271 requirements andproviding the optimum product to meet the severest demands. Important features of the POWERFLO 1541 valve are itspositive sealing, sharp, clean opening and ease of adjustment.
The POWERFLO 1541-3 Bronze Safety Valves with stainless trim are offered in a complete range of sizes from 20mm to65mm. Their maximum operating pressure for steam is 2050kPa and for air is 2400kPa. They are available with screwedbases, with stainless steel base and disc as standard, or with optional bronze trim.
Fig. 1543-3 - High capacity for air, steam and gasThe POWERFLO 1543 valve is a high capacity full lift valve meeting AS1271 requirements and providing the optimumproduct to meet the severest demands.
Important features of the POWERFLO 1543-3 valve are its positive sealing, sharp, clean opening and ease of adjustment.
POWERFLO 1543-3 bronze safety valves are offered in a complete range of sizes from 15 to 50mm. Their maximum operatingpressure for steam and liquid is 2050kPa and for air is 2400kPa. They are available with screwed bases, with stainless steelbase and disc as standard, or with optional bronze trim.
Complies with AS1271-2003
-
- 7 -
Fig. 1551 and 1479Fig. 1551 and 1479Fig. 1551 and 1479Fig. 1551 and 1479Fig. 1551 and 1479
Fig. 1551Fig. 1551Fig. 1551Fig. 1551Fig. 1551
TYPE 1541TYPE 1541TYPE 1541TYPE 1541TYPE 1541Inlet Size mm 20 25 32 40 50 65Outlet Size mm 20 25 32 40 50 65Orifice Area mm2 71 126 198 324 506 830
Screwed InletNet Mass 1kg 1kg 2kg 3.5kg 4.5kg 7.5kgDismantling height 210 216 270 300 340 380
A 169 177 222 246 284 326B 57 62 70 78 90 102C 36 40 50 57 67 86D 57 63 76 88 111 130
Flanged InletC 36 40 50 57 67 86
AS2129 B1 57.5 60 69.5 79 90.5 103ANSI150 B1 57.5 63.5 69.5 79 92 105ANSI300 B1 57.5 63.5 72.5 82.5 93.5 108
D 57 63 76 88 111 130
TYPE 1543 - HIGH CapacityTYPE 1543 - HIGH CapacityTYPE 1543 - HIGH CapacityTYPE 1543 - HIGH CapacityTYPE 1543 - HIGH CapacityInlet Size mm 15 20 25 32 40 50Outlet Size mm 20 25 32 40 50 65Orifice Area mm2 71 126 198 324 506 830
Screwed InletNet Mass 1kg 1kg 2kg 3.5kg 4.5kg 7.5kgDismantling height 210 216 270 300 340 380
A 169 177 222 246 284 326B 57 62 70 78 90 102C 36 40 50 57 67 86D 57 63 76 88 111 130
Flanged InletC 36 40 50 57 67 86
AS2129 B1 57.5 60 69.5 79 90.5 103ANSI150 B1 57.5 63.5 69.5 79 92 105ANSI300 B1 57.5 63.5 72.5 82.5 93.5 108
D 57 63 76 88 111 130
TYPE 1551 and 1479TYPE 1551 and 1479TYPE 1551 and 1479TYPE 1551 and 1479TYPE 1551 and 1479Inlet Size 15 20Outlet Size 25 25Orifice Area (mm2) 127 182
A 150 150B 67 67C 40 40
DIM
EN
SIO
NS
MM
DIM
EN
SIO
NS
MM
DIM
EN
SIO
NS
MM
DIM
EN
SIO
NS
MM
DIM
EN
SIO
NS
MM
MaterialsMaterialsMaterialsMaterialsMaterials SerSerSerSerServiceviceviceviceviceBase Air Liquids Max Pressure kPa Max
Fig. No. & Seat Disc Spindle Spring Gas Water, Oil Steam Air, Gas Liquids Steam Temp
1551 Dezinced BrassHigh
SS 2050 230oC1479 Dezinced Brass
TensileSS 2050 230oC
1551 spl Dezinced BrassBrass
SS 2050 230oC1479 spl Dezinced Brass SS 2050 230oC1541-3 316SS 316SS 316SS SS 2400 2050 230oC1543-3 316SS 316SS 316SS SS 2400 2050 230oCOptional1541 Bronze Bronze 316SS SS 2050 1700 230oC1543 Bronze Bronze 316SS SS 2050 1700 230oCNote: Type 1479 excludes lower adjusting ring.
Fig. 1541 and 1543Fig. 1541 and 1543Fig. 1541 and 1543Fig. 1541 and 1543Fig. 1541 and 1543
-
- 8 -
POWERFLOFIG. 1541 and 1543 SAFETY VALVE
CAPACITY IN KILOGRAMS PER HOUR OF SATURATED STEAMBASED ON 3% OVERPRESSURE AND 90% OF AVERAGE CAPACITY
CALCULATED IN ACCORDANCE WITH AS1271-2003 AND AS3653-1993FOR USE ON FIRED STEAM BOILERS AND HOT WATER BOILERS, ETC.
3570
100150200260300350400414450500550600650690750800850900950
10001034110012001300140015001600170017501800190020002050
D OrificeD OrificeD OrificeD OrificeD Orifice E OrificeE OrificeE OrificeE OrificeE Orifice F OrificeF OrificeF OrificeF OrificeF Orifice G OrificeG OrificeG OrificeG OrificeG Orifice H OrificeH OrificeH OrificeH OrificeH Orifice J OrificeJ OrificeJ OrificeJ OrificeJ Orifice71mm71mm71mm71mm71mm22222 126mm126mm126mm126mm126mm22222 198mm198mm198mm198mm198mm22222 325mm325mm325mm325mm325mm22222 506mm506mm506mm506mm506mm22222 830mm830mm830mm830mm830mm22222
49.0660.5070.3186.66
103.01122.62135.70152.04168.39172.97184.65201.49218.33235.17252.00265.47285.68302.52319.35336.19353.03369.87381.32403.54437.22470.89504.57538.24571.92605.59622.43639.27672.94706.62723.45
87.42107.81125.28154.41183.54218.49241.79270.91300.04308.20329.01359.02389.02419.02449.02473.02509.02539.02569.02599.03629.03659.03679.43719.03779.03839.04899.04959.04
1019.041079.051109.051139.051199.051259.051289.05
136.93168.86196.24241.86287.48342.22378.72424.34469.96482.74515.35562.34609.33656.32703.32740.91797.30844.29891.28938.28985.27
1032.261064.211126.241220.231314.211408.201502.181596.171690.151737.141737.141737.141737.141737.141784.131784.131784.131784.131784.131878.121878.121878.121878.121878.121972.101972.101972.101972.101972.102019.092019.092019.092019.092019.09
224.35276.67321.52396.27471.01560.71620.51695.26770.01790.93844.36921.36998.35
1075.341152.341213.931306.321383.321460.311537.301614.301691.291743.641845.281999.262153.252307.242461.222615.212769.202846.192846.192846.192846.192846.192923.182923.182923.182923.182923.183077.173077.173077.173077.173077.173231.163231.163231.163231.163231.163308.153308.153308.153308.153308.15
350.13431.78501.78618.43735.09875.07968.40
1085.051201.711234.371317.751437.911558.071678.231798.391894.512038.712158.862279.022399.182519.342639.502721.212879.823120.143360.463600.783841.104081.414321.734441.894441.894441.894441.894441.894562.054562.054562.054562.054562.054802.374802.374802.374802.374802.375042.695042.695042.695042.695042.695162.855162.855162.855162.855162.85
574.03707.91822.66
1013.911205.171434.671587.681778.931970.192023.742160.442357.442554.442751.442948.443106.043342.443539.443736.443933.444130.444327.444461.404721.445115.445509.445903.446297.446691.447085.447282.447282.447282.447282.447282.447479.447479.447479.447479.447479.447873.447873.447873.447873.447873.448267.448267.448267.448267.448267.448464.448464.448464.448464.448464.44
NOTES:1. The outlet line must be short as possible and its weight fully supported.2. A back pressure limitation of 276 kPag applies.3. The built-up back pressure shall not exceed 10% of the set pressure.4. Valves are not suitable for corrosive, flammable or toxic service.5. Capacities at set pressures below 414kPag are based on 14kPag overpressure.6. The maximum pressure for the bronze 1541 and 1543 is 1700 kPag. The figures in italics are for
1541-3 and 1543-3 with SST base and disc, which is limited to 2050 kPag on steam service.
15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 154115411541154115411515151515 2020202020 2020202020 2525252525 2525252525 3232323232 3232323232 4040404040 4040404040 5050505050 5050505050 6565656565
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPakPakPakPakPa
Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)
ModelModelModelModelModel
-
- 9 -
POWERFLOFIG. 1541 and 1543 SAFETY VALVE
CAPACITY IN KILOGRAMS PER HOUR OF SATURATED STEAMBASED ON 10% OVERPRESSURE AND 90% OF AVERAGE CAPACITY
CALCULATED IN ACCORDANCE WITH AS1271-2003 AND AS3653-1993
D OrificeD OrificeD OrificeD OrificeD Orifice E OrificeE OrificeE OrificeE OrificeE Orifice F OrificeF OrificeF OrificeF OrificeF Orifice G OrificeG OrificeG OrificeG OrificeG Orifice H OrificeH OrificeH OrificeH OrificeH Orifice J OrificeJ OrificeJ OrificeJ OrificeJ Orifice71mm71mm71mm71mm71mm22222 126mm126mm126mm126mm126mm22222 198mm198mm198mm198mm198mm22222 325mm325mm325mm325mm325mm22222 506mm506mm506mm506mm506mm22222 830mm830mm830mm830mm830mm22222
NOTES:1. The outlet line must be short as possible and its weight fully supported.2. A back pressure limitation of 276 kPag applies.3. The built-up back pressure shall not exceed 10% of the set pressure.4. Valves are not suitable for corrosive, flammable or toxic service.5. Capacities at set pressures below 207 kPag are based on 20.7 kPag overpressure.6. The maximum pressure for the bronze 1541 and 1543 is 1700 kPag. The figures in italics are for
1541-3 and 1543-3 with SST base and disc, which is limited to 2050 kPag on steam service.
15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 154115411541154115411515151515 2020202020 2020202020 2525252525 2525252525 3232323232 3232323232 4040404040 4040404040 5050505050 5050505050 6565656565
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPakPakPakPakPa
Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)
ModelModelModelModelModel
51.3162.7672.5788.91
105.26107.55141.00158.98176.96182.00194.94212.93230.91248.89266.87284.85302.83320.81338.79356.77374.76392.74410.72428.70464.66500.62536.59572.55608.51644.47662.45662.45662.45662.45662.45680.44680.44680.44680.44680.44716.40716.40716.40716.40716.40752.36752.36752.36752.36752.36770.34770.34770.34770.34770.34
3570
100150200207300350400414450500550600650700750800850900950
1000105011001200130014001500160017001750175017501750175018001800180018001800190019001900190019002000200020002000200020502050205020502050
91.43111.82129.30158.42187.55191.63251.24283.28315.31324.29347.35379.39411.43443.47475.51507.55539.59571.63603.66635.70667.74699.78731.82763.86827.94892.01956.09
1020.171084.251148.321180.361180.361180.361180.361180.361212.401212.401212.401212.401212.401276.481276.481276.481276.481276.481340.561340.561340.561340.561340.561372.601372.601372.601372.601372.60
143.21175.15202.52248.14293.77300.15393.52443.70493.89507.94544.07594.26644.44694.62744.81794.99845.17895.36945.54995.72
1045.911096.091146.281196.461296.831397.191497.561597.931698.301798.661848.851848.851848.851848.851848.851899.031899.031899.031899.031899.031999.401999.401999.401999.401999.402099.772099.772099.772099.772099.772149.952149.952149.952149.952149.95
234.65286.97331.82406.57481.32491.78644.76726.98809.20832.22891.42973.65
1055.871138.091220.311302.541384.761466.981549.211631.431713.651795.871878.101960.322124.762289.212453.652618.102782.542946.993029.213029.213029.213029.213029.213111.433111.433111.433111.433111.433275.883275.883275.883275.883275.883440.323440.323440.323440.323440.323522.553522.553522.553522.553522.55
366.20447.86517.85634.51751.16767.49
1006.241134.561262.881298.811391.201519.521647.841776.161904.482032.802161.122289.442417.762546.082674.402802.722931.043059.363316.003572.643829.284085.924342.564599.204727.524727.524727.524727.524727.524855.854855.854855.854855.854855.855112.495112.495112.495112.495112.495369.135369.135369.135369.135369.135497.455497.455497.455497.455497.45
600.38734.26849.02
1040.271231.521258.301649.721860.102070.482129.382280.862491.242701.622912.003122.383332.763543.143753.523963.904174.284384.664595.044805.415015.795436.555857.316278.076698.837119.597540.357750.737750.737750.737750.737750.737961.117961.117961.117961.117961.118381.878381.878381.878381.878381.878802.638802.638802.638802.638802.639013.019013.019013.019013.019013.01
-
- 10 -
POWERFLOFIG. 1541 and 1543 SAFETY VALVE
CAPACITY IN LITRES PER SECOND OF FREE AIR @ 15 Deg CBASED ON 10% OVERPRESSURE AND 90% OF AVERAGE CAPACITY
CALCULATED IN ACCORDANCE WITH AS1271-2003
D OrificeD OrificeD OrificeD OrificeD Orifice E OrificeE OrificeE OrificeE OrificeE Orifice F OrificeF OrificeF OrificeF OrificeF Orifice G OrificeG OrificeG OrificeG OrificeG Orifice H OrificeH OrificeH OrificeH OrificeH Orifice J OrificeJ OrificeJ OrificeJ OrificeJ Orifice71mm71mm71mm71mm71mm22222 126mm126mm126mm126mm126mm22222 198mm198mm198mm198mm198mm22222 325mm325mm325mm325mm325mm22222 506mm506mm506mm506mm506mm22222 830mm830mm830mm830mm830mm22222
NOTES:1. The outlet line must be short as possible and its weight fully supported.2. A back pressure limitation of 276 kPag applies.3. The built-up back pressure shall not exceed 10% of the set pressure.4. Valves are not suitable for corrosive, flammable or toxic service.5. Capacities at set pressures below 207 kPag are based on 20.7 kPag overpressure.6. The maximum pressure for the bronze 1541 and 1543 is 2050 kPag. The figures in italics are for
1541-3 and 1543-3 with SST base and disc, which is limited to 2400 kPag on gas service.
15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 154115411541154115411515151515 2020202020 2020202020 2525252525 2525252525 3232323232 3232323232 4040404040 4040404040 5050505050 5050505050 6565656565
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPakPakPakPakPa
Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)
ModelModelModelModelModel
3570
100150200207260300350400450500550600650690700750800850900950
1000103411001200130014001500160017001750180019002000205021002100210021002100220022002200220022002300230023002300230024002400240024002400
19.0223.2726.9032.9639.0239.8746.9452.2758.9465.6072.2778.9485.6092.2798.94
104.27105.60112.27118.93125.60132.27138.93145.60150.13158.93172.26185.60198.93212.26225.59238.92245.59252.26265.59278.92285.59292.25292.25292.25292.25292.25305.59305.59305.59305.59305.59318.92318.92318.92318.92318.92332.25332.25332.25332.25332.25
33.9041.4547.9358.7369.5371.0483.6493.14
105.02116.90128.77140.65152.53164.41176.29185.79188.16200.04211.92223.80235.67247.55259.43267.51283.19306.94330.70354.45378.21401.96425.72437.60449.48473.23496.99508.87520.74520.74520.74520.74520.74544.50544.50544.50544.50544.50568.25568.25568.25568.25568.25592.01592.01592.01592.01592.01
53.0964.9375.0891.99
108.91111.27131.00145.89164.49183.10201.70220.31238.91257.52276.12291.00294.73313.33331.93350.54369.14387.75406.35419.00443.56480.77517.98555.19592.40629.61666.82685.42704.03741.24778.45797.05815.65815.65815.65815.65815.65852.86852.86852.86852.86852.86890.07890.07890.07890.07890.07927.28927.28927.28927.28927.28
86.99106.39123.01150.72178.44182.32214.64239.03269.51299.99330.48360.96391.44421.92452.41476.79482.89513.37543.85574.34604.82635.30665.79686.51726.75787.72848.68909.65970.61
1031.581092.541123.021153.511214.471275.441305.921336.401336.401336.401336.401336.401397.371397.371397.371397.371397.371458.331458.331458.331458.331458.331519.301519.301519.301519.301519.30
222.57272.20314.75385.65456.55466.48549.20611.59689.59767.58845.57923.57
1001.561079.561157.551219.941235.541313.541391.531469.531547.521625.511703.511756.541859.502015.482171.472327.462483.452639.442795.422873.422951.413107.403263.393341.383419.383419.383419.383419.383419.383575.373575.373575.373575.373575.373731.353731.353731.353731.353731.353887.343887.343887.343887.343887.34
135.76166.03191.98235.23278.47284.53334.98373.04420.61468.18515.75563.33610.90658.47706.04744.10753.61801.19848.76896.33943.90991.47
1039.051071.401134.191229.341324.481419.621514.771609.911705.061752.631800.201895.351990.492038.062085.632085.632085.632085.632085.632180.782180.782180.782180.782180.782275.922275.922275.922275.922275.922371.072371.072371.072371.072371.07
-
- 11 -
POWERFLO1541-SPL, 1541-3-SPL, 1543-SPL, 1543-3-SPL
LIQUID RELIEF VALVECAPCAPCAPCAPCAPACITY IN LITRES PER MINUTE WACITY IN LITRES PER MINUTE WACITY IN LITRES PER MINUTE WACITY IN LITRES PER MINUTE WACITY IN LITRES PER MINUTE WAAAAATER @ 25% OVERPRESSURETER @ 25% OVERPRESSURETER @ 25% OVERPRESSURETER @ 25% OVERPRESSURETER @ 25% OVERPRESSURE
CALCULACALCULACALCULACALCULACALCULATED IN ACCORDANCE WITH AS1271-2003TED IN ACCORDANCE WITH AS1271-2003TED IN ACCORDANCE WITH AS1271-2003TED IN ACCORDANCE WITH AS1271-2003TED IN ACCORDANCE WITH AS1271-2003
D OrificeD OrificeD OrificeD OrificeD Orifice E OrificeE OrificeE OrificeE OrificeE Orifice F OrificeF OrificeF OrificeF OrificeF Orifice G OrificeG OrificeG OrificeG OrificeG Orifice H OrificeH OrificeH OrificeH OrificeH Orifice J OrificeJ OrificeJ OrificeJ OrificeJ Orifice71mm71mm71mm71mm71mm22222 126mm126mm126mm126mm126mm22222 198mm198mm198mm198mm198mm22222 325mm325mm325mm325mm325mm22222 506mm506mm506mm506mm506mm22222 830mm830mm830mm830mm830mm22222
15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 15411541154115411541 15431543154315431543 154115411541154115411515151515 2020202020 2020202020 2525252525 2525252525 3232323232 3232323232 4040404040 4040404040 5050505050 5050505050 6565656565
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPakPakPakPakPa
Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)Inlet Size (mm)
ModelModelModelModelModel
1. Valves are not designed for closed discharge systems. The outlet line must be short as possible, open toatmosphere and its weight fully supported.
2. A back pressure rating of 270 kPag applies only to built-up back pressure conditions, which shall notexceed 10% of the set pressure.
3. A lifting lever will be required on hot water applications where operating temperature exceeds 60 degreesCelsius, so the SPL suffix should not be nominated.
4. Valves are not suitable for corrosive, flammable or toxic service.5. For values of set pressure below 300 kPa, the blowdown shall be a minimum of 60 kPa.6. Nameplate will continue with L being stamped in the capacity box.
3570
100150200250300350400450500550600650700750800850900950
100011001200130014001500160017001800190020002070
22.9332.4338.7647.4854.8261.2967.1472.5277.5382.2386.6890.9194.9598.83
102.56106.16109.64113.01116.29119.48122.58128.56134.28139.76145.04150.13155.05159.83164.46168.97173.36176.36
40.7057.5668.7984.2597.29
108.77119.15128.70137.58145.93153.82161.33168.50175.38182.00188.39194.57200.56206.37212.03217.54228.16238.30248.03257.39266.43275.17283.63291.86299.85307.64312.98
63.9590.44
108.10132.40152.88170.92187.24202.24216.20229.32241.72253.52264.79275.60286.01296.05305.76315.17324.30333.19341.84358.53374.47389.76404.48418.67432.40445.71458.63471.20483.44491.83
104.97148.46177.44217.32250.94280.55307.33331.96354.88376.40396.76416.13434.63452.38469.46485.93501.87517.32532.31546.90561.11588.50614.66639.76663.91687.22709.75731.60752.81773.44793.53807.29
163.44231.13276.26338.35390.69436.80478.49516.83552.52586.03617.73647.88676.69704.32730.91756.56781.37805.42828.77851.48873.60916.24956.98996.06
1033.661069.941105.031139.041172.061204.181235.461256.90
268.09379.13453.15554.99640.85716.49784.88847.77906.30961.28
1013.271062.731109.991155.311198.921241.001281.701321.151359.451396.701432.991502.931569.761633.851695.531755.041812.601868.381922.551975.232026.552061.71
-
126.7mm126.7mm126.7mm126.7mm126.7mm22222 181.8mm181.8mm181.8mm181.8mm181.8mm22222 126.7mm126.7mm126.7mm126.7mm126.7mm22222 181.8mm181.8mm181.8mm181.8mm181.8mm22222 126.7mm126.7mm126.7mm126.7mm126.7mm22222 181.8mm181.8mm181.8mm181.8mm181.8mm22222
15NB15NB15NB15NB15NB 20NB20NB20NB20NB20NB 15NB15NB15NB15NB15NB 20NB20NB20NB20NB20NB 15NB15NB15NB15NB15NB 20NB20NB20NB20NB20NB
POWERFLO1479 and 1551 SAFETY & RELIEF VALVES
IN ACCORDANCE WITH AS1271 FOR USE ON UNFIRED PRESSURE VESSELS,ETC.
NOTES:1. Kilograms per hour saturated steam at 10% overpressure, 90% of average capacity.2. Capacity at set pressure below 206 kPa are based on 21 kPa overpressure.3. Litres per second of free air at (15C) and 10% overpressure, 90% of average capacity.4. Litres per minute of water at (20C) and 25% overpressure.
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPagkPagkPagkPagkPag
Fig. 1551Fig. 1551Fig. 1551Fig. 1551Fig. 1551 Fig. 1551Fig. 1551Fig. 1551Fig. 1551Fig. 1551 Fig. 1479Fig. 1479Fig. 1479Fig. 1479Fig. 1479Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr) Air (l/Sec)Air (l/Sec)Air (l/Sec)Air (l/Sec)Air (l/Sec) WWWWWater (l/Min)ater (l/Min)ater (l/Min)ater (l/Min)ater (l/Min)
35105170205240275345415485585655690725760825860895
10001035110512101275134513801450151515851655172517951860193020002050
527597
109121134160186211248273286299312336348361400412438476500526539564588614639665690714740765784
75108139156174193230266303356392411429447482500518573592629684718755773810844881917954991
1025106210991125
19283640455059697892
101106111116124129134148153162177185195200209218227237246256265274284291
2840525865718599
112132145152159167179185192213219233253266280287300313326340354367380394407417
39.6468.6787.3795.95
103.81111.13124.47136.51147.58162.08
171.5176.03180.44184.74192.48196.52200.48211.91215.59222.76
233.1239.28245.76248.94255.17260.83266.79272.62278.32283.91289.01
294.4299.69303.41
56.8998.53
125.37137.67148.96159.45
178.6195.88211.76232.57246.09252.58
258.9265.08276.18281.98287.66304.07309.34319.63334.47343.34352.64
357.2366.15374.26382.81391.17399.36407.38414.69422.42430.02435.36
- 12 -
-
126.7mm126.7mm126.7mm126.7mm126.7mm22222 181.8mm181.8mm181.8mm181.8mm181.8mm22222
15NB15NB15NB15NB15NB 20NB20NB20NB20NB20NB
BACK PRESSUREBACK PRESSUREBACK PRESSUREBACK PRESSUREBACK PRESSUREDEFINITIONDEFINITIONDEFINITIONDEFINITIONDEFINITION
Back pressure is that pressure foundin the valve body casing and in theexhaust piping from the valve. It isdownstream from the valve nozzle anddisc seat and may affect valveperformance and capacity. Types ofback pressure include:
Super-imposed it exists in the valvebody casing and exhaust piping priorto the valve opening. It consists ofthree types:
Atmospheric normalatmospheric pressure is presentand has no effect on the setpressure or performance of a valveset above 100 kPag.
Constant pressure (higher thanatmospheric) that exists in thebody casing and exhaust piping,but which does not change withtime.
Variable pressure that exists inthe body casing and exhaustpiping, but which is variable innature and changes with time.
Built-up pressure on the exhaustside of the valve that results from flowthrough the valve, after the valve hasopened.
POWERFLO1551 SAFETY VALVES
IN ACCORDANCE WITH AS1271 AND AS3653 FOR USE ONFIRED STEAM BOILERS, ETC.
NOTES:1. Kilograms per hour saturated steam at 3% overpressure, 90% of average capacity.2. Capacity at set pressure below 415 kPa are based on 14 kPa overpressure.
Set PrSet PrSet PrSet PrSet PressuressuressuressuressureeeeekPagkPagkPagkPagkPag
Fig. 1551Fig. 1551Fig. 1551Fig. 1551Fig. 1551Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr)Steam (Kg/Hr)
35105170205240275345415485585655690725760825860895
10001035110512101275134513801450151515851655172517951860193020002050
507395
106118130153176200234258270282294316328340376388412448470494506530553577601625649671695719736
72105136153170186220252287336370388405422454471488540557592643675710727761793828862897931963997
10321056
- 13 -
-
Austral-Powerflo Solutions offers a complete portfolio of pressure relief, control, ball, butterfly, gate, globe andcheck valves, and pressure and temperature instrumentation - our product lines provide world-class market-leading technology. The industries we service include power generation, boiler manufacturing, petroleum oil& gas, chemical, food & beverage, waste gas and water. Austral-Powerflo provides focused effort to supportour Australia-wide customers throughout a products life-cycle. The backbone of this support system is Austral-Powerflos technically competent Salesforce, our Sales/Support Offices and our manufacturing/service operations,backed-up by our technical resources.
As a leading provider of Industrial Valve and Instrumentation solutions, Austral-Powerflo offers world-classaftermarket services. The aftermarket service program is designed to provide consistent and reliable repairservices, technical training, field support, spare parts supply and management, complete equipment replace-ment, and comprehensive diagnostic services.
Austral-Powerflo is committed to providing our customers with quality service throughout the products lifecycle, and ensuring that critical facets of their plant operation are supported. Austral-Powerflos aftermarketservice support is accessible 24 hours a day and seven days a week all year round.
Austral-Powerflo fully understands that quick response in obtaining replacement parts and overhaul servicesis a critical factor in maintaining a smooth operating plant. As a result, Austral-Powerflo has placed extremelyhigh importance on this customer need within our aftermarket program.
ACCREDITED SUPPORT
Austral-Powerflo provides factory-certified support for our products through our Valve Repair and Testing (accreditedby BVQIBVQIBVQIBVQIBVQI to ISO9001ISO9001ISO9001ISO9001ISO9001) and FICO FICO FICO FICO FICO Instrumentation Manufacture, Repair and Testing facilities. Your assurance ofour competence is Austral-Powerflos NANANANANATTTTTAAAAA accreditation for Pressure Gauge Calibration, as well as ourConsolidatedConsolidatedConsolidatedConsolidatedConsolidated Green Tag Center (GTCGTCGTCGTCGTC) and Masoneilan MARCMasoneilan MARCMasoneilan MARCMasoneilan MARCMasoneilan MARC trained and accredited field servicetechnicians. All of these resources provide OEM experience, knowledge and technology to support yourmaintenance and repair needs, including hands-on training and on-site support.
INTEGRATED MAINTENANCE PROGRAMS
We support what we sell!
Austral-Powerflo also provides integrated programs to help manage the support of your installed equipment.These programs are location specific and include plant surveys, data management, scheduling and planningof maintenance, repairs, and overhauls.
Our MasoneilanMasoneilanMasoneilanMasoneilanMasoneilan accredited Control ValveTest Procedures cover leak testing up to Class VIShut-Off, test and calibration of actuators andinstrumentation.
All Valves are fully stroked to ensure correctoperation.
-
NOTES
-
APS
BSR
V-0
411
Austral-Powerflo Solutions Pty LtdACN 000 004 884
Sales Offices: 1300 658 701
SydneyMary Street, Ermington, NSW 2115Tel: 02 9877 8101 Fax: 02 9804 6282Email: [email protected]
MelbourneSuite 48, Building 4,195 Wellington Road, Clayton, VIC 3168Tel: 03 8720 7000 Fax: 03 9720 5522Email: [email protected]
Brisbane6 Imboon Street, Deception Bay, QLD 4508Tel: 07 3897 8100 Fax: 07 3293 4261Email: [email protected]
PerthUnit1/24 Tacoma Circuit, Canning Vale, WA 6155Tel: 08 9456 9600 Fax: 08 9350 6644Email: [email protected]
New Zealand2/6 Findlay Street, Ellerslie, Auckland NZ 1005Tel: (64 9) 525 5454 Fax: (64 9) 579 3106Mob: (64 2) 176 4053Email: [email protected]
Head Office & ManufacturingSafety & Relief Valve Manufacture & ServiceFICO Instrument Manufacture & Service
Mary Street, Ermington, NSW 2115Tel: 02 9877 8100 Fax: 02 9804 7193Email: [email protected]
Website: www.austral-powerflo.com.au