![Page 1: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/1.jpg)
17/04/2012 D. De Venuto 1
Analog CMOS Subcircuits
MOS Diode/Active Resistor Current Sinks and Sources
![Page 2: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/2.jpg)
17/04/2012 D. De Venuto 2
MOS Diode/Active Resistor
• Gate and Drain of MOS transistor are tied together • I-V characteristics are qualitatively similar to a pn-junction
diode (MOS diode) • The MOS diode is used as component of a current mirror
and for level translation (voltage drop).
![Page 3: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/3.jpg)
17/04/2012 D. De Venuto 3
The I-V characteristic • The I-V characteristics of the MOS diode are described by the
large-signal equation for drain current in saturation (the connection of the gate to the drain guarantees operation in saturation region):
(1)
or (2) If V or I is given, then the remaining variable can be designed
using either the equation (1) or the (2) and solving for the value of β.
( )[ ] ( )2222
'TGSTGSD VVVV
LWKII −=−
==
β
β/2 DTDSGS IVVVV +===
![Page 4: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/4.jpg)
17/04/2012 D. De Venuto 4
Small-signal model
• Connecting the gate to the drain means that VDS controls ID and therefore the channel transconductance becomes a channel conductance.
mdsmbsmout gggg
r 11≅
++=
![Page 5: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/5.jpg)
17/04/2012 D. De Venuto 5
Voltage division using active resistor
• An application of the MOS diode is the voltage division, where a bias voltage is generated with respect to ground.
• Noting that VDS=VGS for both devices:
TONTDS VVVIV +=+= β/2
TONDSDSBIAS VVVVV 2221 +=+=
![Page 6: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/6.jpg)
17/04/2012 D. De Venuto 6
Current Sinks and Sources
• A current sink and current source are two terminal components whose current at any instant of time is independent of the voltage across their terminals.
• The current of a current sink or source flows from the
positive node through the sink or source, to the negative node.
• A current sink typically has the negative node at VSS and the current source has the positive node at VDD.
![Page 7: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/7.jpg)
17/04/2012 D. De Venuto 7
• The gate is taken to whatever voltage is necessary to create the desiderate value of current. The voltage divider seen before can be used to provide this voltage.
• We note that in nonsaturation region the MOS is not a good current source. In fact, the voltage across the current sink must be larger than VMIN in order for the current sink to perform properly:
Vout ≥ VGG-VTO
Current sink
![Page 8: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/8.jpg)
17/04/2012 D. De Venuto 8
Current-voltage characteristic and output resistance
• If the source and the bulk are both connected to ground, then the small-signal output resistance is given by:
rout= (1+λVDS)/λlD ≈(λlD)-1
• Vout≤ VGG-|VTO|
![Page 9: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/9.jpg)
17/04/2012 D. De Venuto 9
Advantages and disadvantages
• The advantage of the current sink and source is their simplicity.
• However, there are two areas in which their performance may need to be improved for certain applications:
1) To increase the small-signal output resistance-resulting
in a more constant current over the range of Vout values. 2) To reduce the value of VMIN, thus allowing a larger
range of VOUT over which the current sink/source work properly.
![Page 10: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/10.jpg)
17/04/2012 D. De Venuto 10
Techniques to increase the rout (1) • The small-signal output resistance can be increased
using the principle of the figure.
• The principle uses the common-gate configuration to multiply the source resistance r by the approximate voltage gain of the common-gate configuration with an infinite load resistance.
![Page 11: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/11.jpg)
17/04/2012 D. De Venuto 11
rout Evaluation (1)
• The exact small-signal output resistance rout can be calculated from the small-signal model:
rout=vout/iout=r+rds2+[(gm2+gmbs2)rds2]r≈(gm2rds2)r where gm2rds2>>1 and gm2> gmb2
![Page 12: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/12.jpg)
17/04/2012 D. De Venuto 12
Techniques to increase the rout (2)
• The output resistance of the current sink is increased by the common-gate voltage gain of M2
![Page 13: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/13.jpg)
17/04/2012 D. De Venuto 13
• To verify we use the small-signal output resistance of the cascode current sink.
• Since vgs2=-v1 and vgs1=0, summing the currents at the output node gives:
iout+gm2v1+gmbs2v1=gds2(vout-v1) Since v1=ioutrds1, we can solve for rout as
rout=vout/iout=rds2(1+gm2rds1+gmbs2rds1+gds2rds1)= rds1+rds2+gm2rds1rds2(1+η2); being gmbs2=η2gm2
tipically gm2rds2>1 so rout=(gm2rds2)rds1.
rout Evaluation (2)
![Page 14: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/14.jpg)
17/04/2012 D. De Venuto 14
Relationship between the currents and the W/L of 2 equal devices
• For two transistor M1 and M2, it is assumed that the applied VGS can be divided into two parts, given as:
VGS=VON+VT where VON is that part of VGS in excess of VT. • This definition allows us to express the minimum value of VDS for which
the device remains in saturation: VDS(sat)=VGS-VT=VON Then in saturation the current can be written:
ID=K’W/2L*(VON)2
![Page 15: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/15.jpg)
17/04/2012 D. De Venuto 15
Then if the currents of two MOS are equal (because they are in series) then the following relations holds: If both the transistors are the same type Or The principle above can be used to define a relationship
between the currents:
22
2222
11
11 )(')('ONON V
LWKV
LWK
=
22
222
111 )()( ONON V
LWV
LW
=
21
22
2
2
1
1
)()(
ON
ON
VV
LWLW
=
1
12
2
21 L
WILWI DD =
![Page 16: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/16.jpg)
17/04/2012 D. De Venuto 16
• This relation is useful even though the gate-source terminals of M1 and M2 may not be physically connected because voltages can be identical without being physically connected.
![Page 17: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/17.jpg)
17/04/2012 D. De Venuto 17
Constant output current • The other performance limitation of the simple current
sink/source was the fact that the constant output current could not be obtained for all values of vout.
• While this problem may not be serious in the simple current sink/source, it becomes more severe in the cascode current-sink/source configuration that was used to increase the small-signal output resistance.
• It becomes necessary to reduce VMIN.
• Obviously, VMIN can be reduced by increasing the value of W/L and adjusting the gate-source voltage to get the same output current.
![Page 18: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/18.jpg)
17/04/2012 D. De Venuto 18
Cascode current sink
• Our objective is to use the above principle to reduce the value of VMIN.
![Page 19: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/19.jpg)
17/04/2012 D. De Venuto 19
Standard cascode current sink
If we ignore the bulk effect of M2 and M4 & assume M1=M2=M3=M4, I.e. all matched and same W/L Then the their VGS is given by:
VGS=VT+VON
At the gate of M2 the voltage respect the power supply is: 2VT+2VON To be in saturation VD>VG-VT VD2(min)=VMIN=VT+2VON.
![Page 20: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/20.jpg)
17/04/2012 D. De Venuto 20
• The resulting current-voltage relationship
VMIN is dropped across both M1 and M2. The drop across M2 is VON while the drop across M1 is VT+ VON.
From the demonstration before results that we can still reduce VMIN by VT and still keep both M1 and M2 in saturation!
![Page 21: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/21.jpg)
17/04/2012 D. De Venuto 21
High-swing cascode
• The W/L of M4 is made one-quarter of the identical W/L ratios of M1 and M3.
• This causes that the gate – source voltage across M4 to be VT+2VON rather than VT+VON.
• Consequently the voltage at the gate of M2 is now VT+2VON and then from the relationship seen before:
VD2(min)=VMIN=2VON
![Page 22: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/22.jpg)
17/04/2012 D. De Venuto 22
![Page 23: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/23.jpg)
17/04/2012 D. De Venuto 23
Problems of the High-swing cascode
• The VDS of M1 and the VDS of M3 are not the same. Therefore the current iout will not be an accurate replica of IREF due to channel length modulation as well as drain-induced threshold shift.
• A possible solution is to add an additional transistor M5 in series with M3 so as to force the drain voltages of M3 and M1 to be equal, thus eliminating any errors.
![Page 24: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/24.jpg)
17/04/2012 D. De Venuto 24
Improved high-swing cascode
![Page 25: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/25.jpg)
17/04/2012 D. De Venuto 25
![Page 26: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/26.jpg)
17/04/2012 D. De Venuto 26
![Page 27: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/27.jpg)
17/04/2012 D. De Venuto 27
![Page 28: Analog CMOS Subcircuits - MiXeDsIgNaL · 01/06/2017 · • The MOS diode is used as component of a current mirror and for level translation (voltage drop). 17/04/2012 D. De Venuto](https://reader036.vdocuments.site/reader036/viewer/2022071217/604d3ca483f77246730c86b5/html5/thumbnails/28.jpg)
17/04/2012 D. De Venuto 28
Exercise
• Use the cascode sink configuration to design a current sink of 250 uA and VMIN of 0.5V. K’n=110uA/V^2