adapter rear wing (SRO-GT4)
718 Cayman GT4 Clubsport MR (Typ 982)
Version _V1_2019/02
3
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
Contact
Manthey-Racing GmbH
Technical support
Rudolf-Diesel-Str. 11-13
53520 Meuspath
Germany
Phone: +49 (0) 2691 9338 807
E-Mail: [email protected]
Note Due to the ongoing optimization of our products, this document will be updated on a regular basis. Please note that only the current version of this document is valid. The current documents are available in the download area.
Download area
The installation and operating instructions as well as the technical manuals are available for download under the following link.
http://www.manthey-racing.de/downloads.htm
5
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
1. Warning and safety instructions The classification of the warning and safety information is made using the respecti-ve signal word (Danger, Warning, Caution) in addition to the warning icon.
Warning of death or serious bodily injuries, which will occur in the event of non-compliance.
Warning of death or serious bodily injuries, which may occur in the event of non-compliance.
Warning of minor bodily injuries in the event of non-compliance.
Warning of property damage in the event of non-compliance.
Required tightening torque in Nm
NOTE
DANGER
WARNING
ATTENTION
6
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
General safety instructions
Risk of injury and risk of accident during and after work on the vehicle • Repairs are to be carried out only if access to the repair hand
books in the PIWIS Information System is also available • Observe the safety instructions • Observe the repair handbooks of the vehicle series in the
PIWIS Information System. Crashing vehicle Squeezing or crushing Damage to the vehicle • Do not place any rigid objects under the lifted
vehicle. • Secure lifting platform against lowering. • Remove any rigid objects before lowering. • Lift the vehicle only at the pick-up points designated for the
purpose. • The outer pick-up points should be used as a matter of priority. Improper handling of safety-relevant fitting Injuries
Torque reduction • Use new fastening screws and nuts after every dismantling
• Observe the specified tightening torques. • Visually inspect the parts used
Working with compressed air Eye injuries Damage and contamination of components • Wear safety goggles with side shields • Secure the compressed air discharge point with suitable
materials. • Place the compressed air discharge point on suitable areas. Toxic exhaust fumes Suffocation • When the engine is running, position the exhaust gas extraction system behind the exhaust end pipes of the vehicle and switch it on. Falling objects or loads Squeezing or crushing • Secure components against falling.
GEFAHRDANGER
DANGER
WARNING
WARNING
WARNING
WARNING
7
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
Flying foreign bodies during grinding, drilling and milling Eye injuries • Wear safety goggles.
No heat-resistant materials
Fire • Avoid contact with hot components or sources of ignition. Sharp or sharp-edged objects Cracks, punctures, cuts • Wear personal protective equipment. Hot components Burns • Allow hot components to cool down. • Wear personal protective equipment. Heavy components Crushing • Wear personal protective equipment. • If necessary call somebody to help you. Observe the technical manuals for the 718 Cayman GT4 Clubsport
provided by Porsche AG
WARNUNGWARNING
ATTENTION
ATTENTION
ATTENTION
ATTENTION
8
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
MTH827991B adapter rear wing left side
MTH827992B Adapter rear wing right side
The steps described should be carried out by two mechanics.
NOTE
Due to a change in the SRO homologation regarding the wing connection, the standard adapters (9F2827989 and 9F282990) must be replaced by the two adapters MTH827991B and MTH827992B. This change is mandatory if you participate in a SRO regulated racing series.
NOTE
9
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
Step 1:
Step 1:
Dismantle the rear wing. Loosen and remove the two fastening screws of the connection adapter to the rear wing support on both sides. Take the rear wing including the two adap-ters from the vehicle and place it on a sui-table surface for further steps.
This step should be carried out by two mechanics.
Step 2:
Disassemble the standard adapters 9F2827989 and 9F22827990 from the rear wing. To do this, remove the two panhead screws M6x16 from each adapter.
Keep the standard adapters for a possible retrofitting.
NOTE
Step 2:
NOTE
10
adapters rear wing 718 Cayman GT4 CS MR (Typ 982)
Step 3:
Mount the two new adapters MTH927991B and MTH827992B to the rear wing with the standard panhead screws M6x16.
Step 3:
Step 4:
Reinstall the prepared rear wing to the wing supports. First attach the to front fixing screws by hand. Make sure the spacer is correctly seated between the wing support and the adap-ter. Finally fasten the rear wing to the two rear attachment points. Make sure the spacer is correctly seated between the wing support and the adap-ter. Move the rear wing to the desired position (1-5) and tighten all four countersunk screws M6x12.
8 Nm + Loctite 246
Step 4:
8 Nm + Loctite 246