-
Relion 650 series
Line distance protection REL650Product Guide
-
Contents
1. 650 series overview..............................................3
2. Application...........................................................3
3. Available functions...............................................6
4. Impedance protection........................................17
5. Current protection..............................................19
6. Voltage protection..............................................21
7. Frequency protection.........................................22
8. Secondary system supervision..........................23
9. Control................................................................23
10. Scheme communication....................................25
11. Logic..................................................................26
12. Monitoring.........................................................28
13. Metering............................................................30
14. Human Machine interface.................................31
15. Basic IED functions...........................................31
16. Station communication.....................................32
17. Hardware description........................................33
18. Connection diagrams........................................35
19. Technical data...................................................41
20. Ordering............................................................88
Disclaimer
The information in this document is subject to change without notice and should not be construed as a commitment by ABB AB. ABB AB assumesno responsibility for any errors that may appear in this document.
Copyright 2011 ABB AB.
All rights reserved.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or product names mentioned in this document may be trademarks orregistered trademarks of their respective holders.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
2 ABB
-
1. 650 series overview
The 650 series IEDs provide optimum 'off-the-shelf', ready-to-use solutions. It is configuredwith complete protection functionality anddefault parameters to meet the needs of awide range of applications for generationtransmission and sub-transmission grids.
The 650 series IEDs include:
Complete ready-made solutions optimizedfor a wide range of applications forgeneration, transmission and sub-transmission grids.
Support for user-defined names in the locallanguage for signal and functionengineering.
Minimized parameter setting based ondefault values and ABB's new global basevalue concept. You only need to set thoseparameters specific to your ownapplication, such as the line data.
GOOSE messaging for horizontalcommunication.
Extended HMI functionality with 15dynamic three-color-indication LEDs perpage, on up to three pages, andconfigurable push-button shortcuts fordifferent actions.
Programmable LED text-based labels. Settable 1A/5A -rated current inputs.
2. Application
REL650 is used for the protection, controland monitoring of overhead lines and cablesin solidly or impedance earthed networks.The IED can be used up to the high voltagelevels. It is suitable for the protection ofheavily loaded lines and multi-terminal lineswhere the requirement for fast three-phasetripping is wanted.
The full scheme distance protection providesprotection of power lines with highsensitivity and low requirement on remote
end communication. The five zones havefully independent measuring and settingwhich gives high flexibility for all types oflines.
The modern technical solution offers fastoperating time of typically 1.5 cycles.
The autoreclose includes priority features forsingle-breaker arrangements. It co-operateswith the synchrocheck function with high-speed or delayed reclosing.
High set instantaneous phase and earthovercurrent, four step directional or non-directional delayed phase and earthovercurrent, sensitive earth fault for notdirect earthed systems, thermal overload andtwo step under and overvoltage protectionare examples of the available functionsallowing the user to fulfill any applicationrequirement.
The distance and earth fault protection cancommunicate with remote end in anyteleprotection communication scheme.
The advanced logic capability, where the userlogic is prepared with a graphical tool, allowsspecial applications.
Disturbance recording and fault locator areavailable to allow independent post-faultanalysis after primary disturbances.
Three packages has been defined forfollowing applications:
Five zone distance protection withquadrilateral characteristic (A01)
Five zone distance protection with mhocharacteristic (A05)
Five zone distance protection withquadrilateral characteristic, single poletripping (A11)
The packages are configured and ready fordirect use. Analogue and tripping IO hasbeen pre-defined for basic use.
Add binary I/O as required for theapplication when ordering. Other signalsneed to be applied as required for eachapplication.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
Revision: -
ABB 3
-
The graphical configuration tool ensuressimple and fast testing and commissioning.
REL650 A01 Quad Distance Zones, Single Breaker 10AI (4I+1I+5U)
SMB RREC
79 0->1
SMP PTRC
94 1->0
TCS SCBR
Cond
SPVN ZBAT
Cond
Other configured functions
OV2 PTOV
59 U>
PH PIOC
50 3I>>
CC RBRF
50BF 3I> BF
V MMXU
Meter.
QA1
QB1 QB2
QB9
QC9
QC2
QC1
WA1
WA2
V MSQI
Meter.
DRP RDRE
Mont.
EF PIOC
50N IN>>
CC RPLD
52PD PD
S SCBR
Cond
L PTTR
26 q>
EF4 PTOC
51N/67N IN>
OC4 PTOC
51/67 3I>
BRC PTOC
46 Iub
SDEPSDE
67N IN
STB PTOC
50STB I>
GOP PDOP
32 P>
GUP PDUP
37 P>
CC RBRF
50BF 3I> BF
V MMXU
Meter.
QA1
QB1 QB2
QB9
QC9
QC2
QC1
WA1
WA2
V MSQI
Meter.
DRP RDRE
Mont.
EF PIOC
50N IN>>
CC RPLD
52PD PD
S SCBR
Cond
L PTTR
26 q>
EF4 PTOC
51N/67N IN>
OC4 PTOC
51/67 3I>
BRC PTOC
46 Iub
SDEPSDE
67N IN
STB PTOC
50STB I>
GOP PDOP
32 P>
GUP PDUP
37 P
EF4 PTOC
51N/67N IN>
BRC PTOC
46 Iub
SDE PSDE
37 2I
GOP PDOP
32 P>
GUP PDUP
37 P0
STB RREC
79 0->1
CSP RBRF
50BF 3I> BF
VN MMXU
Meter.
DNP
ANSI IEC
Function Disabled in Settings
IEC60870-5-103
ANSI IEC
IEC10000342 V1 EN
Figure 3. A typical protection application for quadrilateral characteristic distance zones in asingle breaker arrangement, single pole tripping
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
6 ABB
-
3. Available functions
Main protection functions
IEC 61850/Functionblock name
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
Impedance protection
ZQDPDIS 21 Five zone distance protection,quadrilateral characteristic
1 1
FDPSPDIS 21 Phase selection with loadenchroachment, quadrilateralcharacteristic
1 1
ZMOPDIS 21 Five zone distance protection, mhocharacteristic
1
FMPSPDIS 21 Faulty phase identification with loadenchroachment for mho
1
ZDNRDIR 21 Directional impedance quadrilateral andmho
1 1 1
PPLPHIZ Phase preference logic 1 1 1
ZMRPSB 68 Power swing detection 1 1 1
ZCVPSOF Automatic switch onto fault logic,voltage and current based
1 1 1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 7
-
Back-up protection functions
IEC 61850/Functionblockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
Current protection
PHPIOC 50 Instantaneous phase overcurrentprotection
1 1
SPTPIOC 50 Instantaneous phase overcurrentprotection
1
OC4PTOC 51/67 Four step directional phase overcurrentprotection
1 1
OC4SPTOC 51/67 Four step phase overcurrent protection 1
EFPIOC 50N Instantaneous residual overcurrentprotection
1 1 1
EF4PTOC 51N/67N
Four step directional residualovercurrent protection
1 1 1
SDEPSDE 67N Sensitive directional residualovercurrent and power protection
1 1 1
UC2PTUC 37 Time delayed 2-step undercurrentprotection
1 1 1
LPTTR 26 Thermal overload protection, one timeconstant
1 1 1
CCRBRF 50BF Breaker failure protection 1 1
CSPRBRF 50BF Breaker failure protection 1
STBPTOC 50STB Stub protection 1 1 1
CCRPLD 52PD Pole discordance protection 1 1 1
BRCPTOC 46 Broken conductor check 1 1 1
GUPPDUP 37 Directional underpower protection 1 1 1
GOPPDOP 32 Directional overpower protection 1 1 1
DNSPTOC 46 Negative sequence based overcurrentfunction
1 1 1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
8 ABB
-
IEC 61850/Functionblockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
Voltage protection
UV2PTUV 27 Two step undervoltage protection 1 1 1
OV2PTOV 59 Two step overvoltage protection 1 1 1
ROV2PTOV 59N Two step residual overvoltageprotection
1 1 1
LOVPTUV 27 Loss of voltage check 1 1 1
Frequency protection
SAPTUF 81 Underfrequency function 2 2 2
SAPTOF 81 Overfrequency function 2 2 2
SAPFRC 81 Rate-of-change frequency protection 2 2 2
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 9
-
Control and monitoring functions
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
Control
SESRSYN 25 Synchrocheck, energizing check,and synchronizing
1 1 1
SMBRREC 79 Autorecloser 1 1
STBRREC 79 Autorecloser 1
QCBAY Bay control 1 1 1
LOCREM Handling of LR-switch positions 1 1 1
LOCREMCTRL LHMI control of Permitted SourceTo Operate (PSTO)
1 1 1
SLGGIO Logic Rotating Switch for functionselection and LHMI presentation
15 15 15
VSGGIO Selector mini switch extension 20 20 20
DPGGIO IEC 61850 generic communication I/O functions double point
16 16 16
SPC8GGIO Single point generic control 8 signals 5 5 5
AUTOBITS AutomationBits, command functionfor DNP3.0
3 3 3
I103CMD Function commands forIEC60870-5-103
1 1 1
I103IEDCMD IED commands for IEC60870-5-103 1 1 1
I103USRCMD Function commands user definedfor IEC60870-5-103
4 4 4
I103GENCMD Function commands generic forIEC60870-5-103
50 50 50
I103POSCMD IED commands with position andselect for IEC60870-5-103
50 50 50
Secondary system supervision
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
10 ABB
-
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
CCSRDIF 87 Current circuit supervision 1 1 1
SDDRFUF Fuse failure supervision 1 1 1
TCSSCBR Breaker close/trip circuit monitoring 3 3 3
Logic
SMPPTRC 94 Tripping logic 1 1
SPTPTRC 94 Tripping logic 1
TMAGGIO Trip matrix logic 12 12 12
OR Configurable logic blocks, OR gate 283 283 283
INVERTER Configurable logic blocks, Invertergate
140 140 140
PULSETIMER Configurable logic blocks, Pulsetimer
40 40 40
GATE Configurable logic blocks,Controllable gate
40 40 40
XOR Configurable logic blocks, exclusiveOR gate
40 40 40
LOOPDELAY Configurable logic blocks, loop delay 40 40 40
TIMERSET Configurable logic blocks, timerfunction block
40 40 40
AND Configurable logic blocks, AND gate 280 280 280
SRMEMORY Configurable logic blocks, set-resetmemory flip-flop gate
40 40 40
RSMEMORY Configurable logic blocks, reset-setmemory flip-flop gate
40 40 40
FXDSIGN Fixed signal function block 1 1 1
B16I Boolean 16 to Integer conversion 16 16 16
B16IFCVI Boolean 16 to Integer conversionwith logic node representation
16 16 16
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 11
-
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
IB16A Integer to Boolean 16 conversion 16 16 16
IB16FCVB Integer to Boolean 16 conversionwith logic node representation
16 16 16
Monitoring
CVMMXN Measurements 6 6 6
CMMXU Phase current measurement 10 10 10
VMMXU Phase-phase voltage measurement 6 6 6
CMSQI Current sequence componentmeasurement
6 6 6
VMSQI Voltage sequence measurement 6 6 6
VNMMXU Phase-neutral voltage measurement 6 6 6
CNTGGIO Event counter 5 5 5
DRPRDRE Disturbance report 1 1 1
AxRADR Analog input signals 4 4 4
BxRBDR Binary input signals 6 6 6
SPGGIO IEC 61850 generic communication I/O functions
64 64 64
SP16GGIO IEC 61850 generic communication I/O functions 16 inputs
16 16 16
MVGGIO IEC 61850 generic communication I/O functions
16 16 16
MVEXP Measured value expander block 66 66 66
LMBRFLO Fault locator 1 1 1
SPVNZBAT Station battery supervision 1 1 1
SSIMG 63 Insulation gas monitoring function 1 1 1
SSIML 71 Insulation liquid monitoring function 1 1 1
SSCBR Circuit breaker condition monitoring 1 1 1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
12 ABB
-
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
I103MEAS Measurands for IEC60870-5-103 1 1 1
I103MEASUSR Measurands user defined signals forIEC60870-5-103
3 3 3
I103AR Function status auto-recloser forIEC60870-5-103
1 1 1
I103EF Function status earth-fault forIEC60870-5-103
1 1 1
I103FLTPROT Function status fault protection forIEC60870-5-103
1 1 1
I103IED IED status for IEC60870-5-103 1 1 1
I103SUPERV Supervison status for IEC60870-5-103 1 1 1
I103USRDEF Status for user defined signals forIEC60870-5-103
20 20 20
Metering
PCGGIO Pulse counter logic 16 16 16
ETPMMTR Function for energy calculation anddemand handling
3 3 3
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 13
-
Designed to communicate
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
Station communication
IEC 61850 communicationprotocol, LAN1
1 1 1
DNP3.0 for TCP/IPcommunication protocol, LAN1
1 1 1
IEC61870-5-103 IEC60870-5-103 serialcommunication via ST
1 1 1
GOOSEINTLKRCV Horizontal communication viaGOOSE for interlocking
59 59 59
GOOSEBINRCV GOOSE binary receive 4 4 4
GOOSEDPRCV GOOSE function block to receivea double point value
32 32 32
GOOSEINTRCV GOOSE function block to receivean integer value
32 32 32
GOOSEMVRCV GOOSE function block to receivea mesurand value
16 16 16
GOOSESPRCV GOOSE function block to receivea single point value
64 64 64
Scheme communication
ZCPSCH 85 Scheme communication logic fordistance or overcurrent protection
1 1 1
ZCRWPSCH 85 Current reversal and weak-endinfeed logic for distanceprotection
1 1
ZCWSPSCH 85 Current reversal and weak-endinfeed logic for distanceprotection
1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
14 ABB
-
IEC 61850/Function blockname
ANSI Function description Line Distance
REL650 (
A01)
3P
h/1
CB
, quad
REL650 (
A05)
3P
h/1
CB
, m
ho
REL650 (
A11)
1P
h/1
CB
ZCLCPLAL Local acceleration logic 1 1 1
ECPSCH 85 Scheme communication logic forresidual overcurrent protection
1 1 1
ECRWPSCH 85 Current reversal and weak-endinfeed logic for residualovercurrent protection
1 1 1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 15
-
Basic IED functions
IEC 61850/Function blockname
Function description
Basic functions included in all products
INTERRSIG Self supervision with internal event list 1
SELFSUPEVLST Self supervision with internal event list 1
SNTP Time synchronization 1
TIMESYNCHGEN Time synchronization 1
DTSBEGIN,DTSEND,TIMEZONE
Time synchronization, daylight saving 1
IRIG-B Time synchronization 1
SETGRPS Setting group handling 1
ACTVGRP Parameter setting groups 1
TESTMODE Test mode functionality 1
CHNGLCK Change lock function 1
TERMINALID IED identifiers 1
PRODINF Product information 1
PRIMVAL Primary system values 1
SMAI_20_1-12 Signal matrix for analog inputs 2
3PHSUM Summation block 3 phase 12
GBASVAL Global base values for settings 6
ATHSTAT Authority status 1
ATHCHCK Authority check 1
FTPACCS FTP access with password 1
DOSFRNT Denial of service, frame rate control for front port 1
DOSLAN1 Denial of service, frame rate control for LAN1 1
DOSSCKT Denial of service, socket flow control 1
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
16 ABB
-
4. Impedance protection
Five zone distance protection,quadrilateral characteristicZQDPDIS
Five zone distance protection, quadrilateralcharacteristic ZQDPDIS is a five zone fullscheme protection with three fault loops forphase-to-phase faults and three fault loopsfor phase-to-earth fault for each of theindependent zones. Individual settings foreach zone in resistive and reactive reachgives flexibility for use as back-up protectionfor transformer connected to overhead linesand cables of different types and lengths.
ZQDPDIS together with Phase selection withload encroachment FDPSPDIS hasfunctionality for load encroachment, whichincreases the possibility to detect highresistive faults on heavily loaded lines, asshown in figure4.
en05000034.vsd
R
X
Forwardoperation
Reverseoperation
IEC05000034 V1 EN
Figure 4. Typical quadrilateral distanceprotection zone with Phase selectionwith load encroachment functionFDPSPDIS activated
Built-in adaptive load compensationalgorithm prevents overreaching of all zonesat phase-to-earth faults on heavily loadedpower lines.
The distance protection zones can operateindependently of each other in directional(forward or reverse) or non-directional mode.This makes them suitable, together withdifferent communication schemes, for theprotection of power lines and cables incomplex network configurations, such asparallel lines, multi-terminal lines, and so on.
Phase selection, quadrilateralcharacteristic with fixed angleFDPSPDIS
The operation of transmission networkstoday is in many cases close to the stabilitylimit. Due to environmental considerations,the rate of expansion and reinforcement ofthe power system is reduced, for example,difficulties to get permission to build newpower lines. Phase selection, quadrilateralcharacteristic with fixed angle FDPSPDIS isdesigned to accurately select the proper faultloop in the distance function dependent onthe fault type.
The heavy load transfer that is common inmany transmission networks may make faultresistance coverage difficult to achieve.Therefore, FDPSPDIS has a built-in algorithmfor load encroachment, which gives thepossibility to enlarge the resistive setting ofboth the phase selection and the measuringzones without interfering with the load.
The extensive output signals from the phaseselection gives also important informationabout faulty phase(s), which can be used forfault analysis.
Five zone distance protection, mhocharacteristic ZMOPDIS
The numerical mho line distance protection isa five zone full scheme protection for back-up detection of short circuit and earth faults.The full scheme technique provides back-upprotection of power lines with highsensitivity and low requirement on remoteend communication. The five zones havefully independent measuring and settings,which gives high flexibility for all types oflines.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 17
-
The IED can be used up to high voltagelevels. It is suitable for the protection ofheavily loaded lines and multi-terminal lineswhere the requirement for fast three-phasetripping is wanted.
Built-in adaptive load compensationalgorithm prevents overreaching at phase-to-earth faults on heavily loaded power lines,see figure 5.
en07000117.vsd
jX
Operation area Operation area
R
Operation area
No operation area No operation area
IEC07000117 V1 EN
Figure 5. Load encroachment influence onthe offset mho characteristic
The distance protection zones can operate,independent of each other, in directional(forward or reverse) or non-directional mode(offset). This makes them suitable, togetherwith different communication schemes, forthe protection of power lines and cables incomplex network configurations, such asparallel lines, multi-terminal lines and so on.
Faulty phase identification withload encroachment FMPSPDIS
The phase selection function is design toaccurate select the proper fault loop in thedistance function dependent on the fault type.
The heavy load transfer that is common inmany transmission networks may in somecases interfere with the distance protectionzone reach and cause unwanted operation.Therefore the function has a built inalgorithm for load encroachment, which givesthe possibility to enlarge the resistive setting
of the measuring zones without interferingwith the load.
The output signals from the phase selectionfunction produce important informationabout faulty phase(s), which can be used forfault analysis as well.
Directional impedance quadrilateraland mho ZDNRDIR
The evaluation of the direction to the fault ismade in the directional element ZDNRDIR forthe quadrilateral and mho characteristicdistance protections ZQDPDIS and ZMOPDIS.
Phase preference logic PPLPHIZ
Phase preference logic function PPLPHIZ isintended to be used in isolated or highimpedance earthed networks where there is arequirement to trip only one of the faultylines at cross-country fault.
Phase preference logic inhibits tripping forsingle phase-to-earth faults in isolated andhigh impedance earthed networks, wheresuch faults are not to be cleared by distanceprotection. For cross-country faults, the logicselects either the leading or the lagging phase-earth loop for measurement and initiatestripping of the preferred fault based on theselected phase preference. A number ofdifferent phase preference combinations areavailable for selection.
Power swing detection ZMRPSB
Power swings may occur after disconnectionof heavy loads or trip of big generation plants.
Power swing detection function (ZMRPSB) isused to detect power swings and initiateblock of selected distance protection zones.Occurrence of earth-fault currents during apower swing inhibits the ZMRPSB function toallow fault clearance.
Automatic switch onto fault logic,voltage and current based ZCVPSOF
Automatic switch onto fault logic, voltage andcurrent based (ZCVPSOF) is a function thatgives an instantaneous trip at closing ofbreaker onto a fault. A dead line detection
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
18 ABB
-
check is provided to activate the functionwhen the line is dead.
Mho distance protections can not operate forswitch onto fault condition when the phasevoltages are close to zero. An additional logicbased on UI Level is used for this purpose.
5. Current protection
Instantaneous phase overcurrentprotection PHPIOC
The instantaneous three phase overcurrentfunction has a low transient overreach andshort tripping time to allow use as a high setshort-circuit protection function.
Instantaneous phase overcurrentprotection SPTPIOC
The instantaneous three phase overcurrentfunction has a low transient overreach andshort tripping time to allow use as a high setshort-circuit protection function.
Four step phase overcurrentprotection OC4PTOC
The four step phase overcurrent protectionfunction OC4PTOC has an inverse or definitetime delay independent for step 1 and 4separately. Step 2 and 3 are always definitetime delayed.
All IEC and ANSI time delayed characteristicsare available.
The directional function is voltage polarizedwith memory. The function can be set to bedirectional or non-directional independentlyfor each of the steps.
Four step phase overcurrentprotection OC4SPTOC
The four step phase overcurrent function(OC4SPTOC) has an inverse or definite timedelay independent for each step separately.
All IEC and ANSI time delayed characteristicsare available.
The directional function is voltage polarizedwith memory. The function can be set to bedirectional or non-directional independentlyfor each of the steps.
Instantaneous residual overcurrentprotection EFPIOC
The Instantaneous residual overcurrentprotection EFPIOC has a low transientoverreach and short tripping times to allowthe use for instantaneous earth-faultprotection, with the reach limited to less thanthe typical eighty percent of the line atminimum source impedance. EFPIOC can beconfigured to measure the residual currentfrom the three-phase current inputs or thecurrent from a separate current input.EFPIOC can be blocked by activating theinput BLOCK.
Four step residual overcurrentprotection EF4PTOC
The four step residual overcurrent protection(EF4PTOC) has a settable inverse or definitetime delay independent for step 1 and 4separately. Step 2 and 3 are always definitetime delayed.
All IEC and ANSI time delayed characteristicsare available.
The directional function is voltage polarized,current polarized or dual polarized.
EF4PTOC can be set directional or non-directional independently for each of the steps.
A second harmonic blocking can be setindividually for each step.
EF4PTOC can be used as main protection forphase-to-earth faults.
EF4PTOC can also be used to provide asystem back-up for example, in the case ofthe primary protection being out of servicedue to communication or voltage transformercircuit failure.
Directional operation can be combinedtogether with corresponding communicationlogic in permissive or blocking teleprotectionscheme. Current reversal and weak-endinfeed functionality are available as well.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 19
-
Sensitive directional residualovercurrent and power protectionSDEPSDE
In isolated networks or in networks withhigh impedance earthing, the earth faultcurrent is significantly smaller than the shortcircuit currents. In addition to this, themagnitude of the fault current is almostindependent on the fault location in thenetwork. The protection can be selected touse either the residual current or residualpower component 3U03I0cos j, foroperating quantity. There is also availableone non-directional 3I0 step and one non-
directional 3U0 overvoltage tripping step.
Time delayed 2-step undercurrentprotection UC2PTUC
Time delayed 2-step undercurrent protection(UC2PTUC function is used to supervise theline for low current, for example, to detect aloss-of-load condition, which results in acurrent lower than the normal load current.
Thermal overload protection, onetime constant LPTTR
The increasing utilizing of the power systemcloser to the thermal limits has generated aneed of a thermal overload protection alsofor power lines.
A thermal overload will often not be detectedby other protection functions and theintroduction of the thermal overloadprotection can allow the protected circuit tooperate closer to the thermal limits.
The three-phase current measuring protection
has an I2t characteristic with settable timeconstant and a thermal memory.
An alarm level gives early warning to allowoperators to take action well before the lineis tripped.
Breaker failure protection CCRBRF
Breaker failure protection (CCRBRF) ensuresfast back-up tripping of surrounding breakersin case the own breaker failure to open.CCRBRF can be current based, contact based,
or an adaptive combination of these twoprinciples.
A current check with extremely short resettime is used as check criterion to achieve ahigh security against unnecessary operation.
A contact check criteria can be used wherethe fault current through the breaker is small.
Breaker failure protection (CCRBRF) currentcriteria can be fulfilled by one or two phasecurrents, or one phase current plus residualcurrent. When those currents exceed the userdefined settings, the function is activated.These conditions increase the security of theback-up trip command.
CCRBRF function can be programmed to givea three-phase re-trip of the own breaker toavoid unnecessary tripping of surroundingbreakers at an incorrect initiation due tomistakes during testing.
Breaker failure protection CSPRBRF
Breaker failure protection CSPRBRF ensuresfast back-up tripping of surrounding breakersin case of own breaker failure to open.CSPRBRF can be current based, contactbased, or adaptive combination betweenthese two principles.
A current check with extremely short resettime is used as a check criterion to achieve ahigh security against unnecessary operation.
A contact check criteria can be used wherethe fault current through the breaker is small.
CSPRBRF function current criteria can befulfilled by one or two phase currents, or onephase current plus residual current. Whenthose currents exceed the user definedsettings, the function is activated. Theseconditions increase the security of the back-up trip command.
CSPRBRF can be programmed to give a three-phase re-trip of the own breaker to avoidunnecessary tripping of surrounding breakersat an incorrect initiation due to mistakesduring testing.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
20 ABB
-
Stub protection STBPTOC
When a power line is taken out of service formaintenance and the line disconnector isopened the voltage transformers will mostlybe outside on the disconnected part. Theprimary line distance protection will thus notbe able to operate and must be blocked.
The stub protection STBPTOC covers thezone between the current transformers andthe open disconnector. The three-phaseinstantaneous overcurrent function isreleased from a normally open, NO (b)auxiliary contact on the line disconnector.
Pole discordance protectionCCRPLD
Circuit breakers and disconnectors can endup with the poles in different positions (close-open), due to electrical or mechanicalfailures. This can cause negative and zerosequence currents which cause thermal stresson rotating machines and can causeunwanted operation of zero sequence ornegative sequence current functions.
Normally the own breaker is tripped tocorrect such a situation. If the situationpersists the surrounding breakers should betripped to clear the unsymmetrical loadsituation.
The pole discordance function operates basedon information from the circuit breaker logicwith additional criteria from unsymmetricalphase currents when required.
Broken conductor check BRCPTOC
Conventional protection functions can notdetect the broken conductor condition.Broken conductor check (BRCPTOC)function, consisting of continuous currentunsymmetrical check on the line where theIED is connected will give alarm or trip atdetecting broken conductors.
Directional over/underpowerprotection GOPPDOP/GUPPDUP
The directional over-/under-power protectionGOPPDOP/GUPPDUP can be used wherever
a high/low active, reactive or apparent powerprotection or alarming is required. Thefunctions can alternatively be used to checkthe direction of active or reactive power flowin the power system. There are a number ofapplications where such functionality isneeded. Some of them are:
detection of reversed active power flow detection of high reactive power flow
Each function has two steps with definitetime delay. Reset times for both steps can beset as well.
Negative sequence basedovercurrent function DNSPTOC
Negative sequence based overcurrentfunction (DNSPTOC) is typically used assensitive earth-fault protection of powerlines, where incorrect zero sequencepolarization may result from mutualinduction between two or more parallel lines.
Additionally, it is applied in applications onunderground cables, where zero sequenceimpedance depends on the fault currentreturn paths, but the cable negative sequenceimpedance is practically constant.
The directional function is current andvoltage polarized. The function can be set toforward, reverse or non-directionalindependently for each step.
DNSPTOC protects against all unbalancedfaults including phase-to-phase faults. Theminimum start current of the function mustbe set to above the normal system unbalancelevel in order to avoid unintentionalfunctioning.
6. Voltage protection
Two step undervoltage protectionUV2PTUV
Undervoltages can occur in the power systemduring faults or abnormal conditions. Twostep undervoltage protection (UV2PTUV)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 21
-
function can be used to open circuit breakersto prepare for system restoration at poweroutages or as long-time delayed back-up toprimary protection.
UV2PTUV has two voltage steps, where step1 is settable as inverse or definite timedelayed. Step 2 is always definite time delayed.
Two step overvoltage protectionOV2PTOV
Overvoltages may occur in the power systemduring abnormal conditions such as suddenpower loss, tap changer regulating failures,open line ends on long lines etc.
OV2PTOV has two voltage steps, where step1 can be set as inverse or definite timedelayed. Step 2 is always definite time delayed.
OV2PTOV has an extremely high reset ratioto allow settings close to system servicevoltage.
Two step residual overvoltageprotection ROV2PTOV
Residual voltages may occur in the powersystem during earth faults.
Two step residual overvoltage protectionROV2PTOV function calculates the residualvoltage from the three-phase voltage inputtransformers or measures it from a singlevoltage input transformer fed from an opendelta or neutral point voltage transformer.
ROV2PTOV has two voltage steps, wherestep 1 can be set as inverse or definite timedelayed. Step 2 is always definite time delayed.
Loss of voltage check LOVPTUV
Loss of voltage check (LOVPTUV) is suitablefor use in networks with an automatic systemrestoration function. LOVPTUV issues a three-pole trip command to the circuit breaker, ifall three phase voltages fall below the setvalue for a time longer than the set time andthe circuit breaker remains closed.
7. Frequency protection
Underfrequency protection SAPTUF
Underfrequency occurs as a result of lack ofgeneration in the network.
Underfrequency protection SAPTUF is usedfor load shedding systems, remedial actionschemes, gas turbine startup and so on.
SAPTUF is provided with an undervoltageblocking.
Overfrequency protection SAPTOF
Overfrequency protection function SAPTOF isapplicable in all situations, where reliabledetection of high fundamental power systemfrequency is needed.
Overfrequency occurs at sudden load dropsor shunt faults in the power network. Closeto the generating plant, generator governorproblems can also cause over frequency.
SAPTOF is used mainly for generationshedding and remedial action schemes. It isalso used as a frequency stage initiating loadrestoring.
SAPTOF is provided with an undervoltageblocking.
Rate-of-change frequencyprotection SAPFRC
Rate-of-change frequency protection function(SAPFRC) gives an early indication of a maindisturbance in the system. SAPFRC can beused for generation shedding, load sheddingand remedial action schemes. SAPFRC candiscriminate between positive or negativechange of frequency.
SAPFRC is provided with an undervoltageblocking.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
22 ABB
-
8. Secondary systemsupervision
Current circuit supervisionCCSRDIF
Open or short circuited current transformercores can cause unwanted operation of manyprotection functions such as differential,earth-fault current and negative-sequencecurrent functions.
It must be remembered that a blocking ofprotection functions at an occurrence of openCT circuit will mean that the situation willremain and extremely high voltages willstress the secondary circuit.
Current circuit supervision (CCSRDIF)compares the residual current from a threephase set of current transformer cores withthe neutral point current on a separate inputtaken from another set of cores on thecurrent transformer.
A detection of a difference indicates a fault inthe circuit and is used as alarm or to blockprotection functions expected to giveunwanted tripping.
Fuse failure supervision SDDRFUF
The aim of the fuse failure supervisionfunction (SDDRFUF) is to block voltagemeasuring functions at failures in thesecondary circuits between the voltagetransformer and the IED in order to avoidunwanted operations that otherwise mightoccur.
The fuse failure supervision function basicallyhas three different algorithms, negativesequence and zero sequence basedalgorithms and an additional delta voltageand delta current algorithm.
The negative sequence detection algorithm isrecommended for IEDs used in isolated orhigh-impedance earthed networks. It is basedon the negative-sequence measuringquantities, a high value of voltage 3U2
without the presence of the negative-sequence current 3I2.
The zero sequence detection algorithm isrecommended for IEDs used in directly orlow impedance earthed networks. It is basedon the zero sequence measuring quantities, ahigh value of voltage 3U0 without the
presence of the residual current 3I0.
A criterion based on delta current and deltavoltage measurements can be added to thefuse failure supervision function in order todetect a three phase fuse failure, which inpractice is more associated with voltagetransformer switching during stationoperations.
For better adaptation to system requirements,an operation mode setting has beenintroduced which makes it possible to selectthe operating conditions for negativesequence and zero sequence based function.The selection of different operation modesmakes it possible to choose differentinteraction possibilities between the negativesequence and zero sequence based algorithm.
Breaker close/trip circuitmonitoring TCSSCBR
The trip circuit supervision function TCSSCBRis designed to supervise the control circuit ofthe circuit breaker. The invalidity of a controlcircuit is detected by using a dedicatedoutput contact that contains the supervisionfunctionality.
The function operates after a predefinedoperating time and resets when the faultdisappears.
9. Control
Synchrocheck, energizing check,and synchronizing SESRSYN
The Synchronizing function allows closing ofasynchronous networks at the correct
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 23
-
moment including the breaker closing time,which improves the network stability.
Synchrocheck, energizing check, andsynchronizing (SESRSYN) function checksthat the voltages on both sides of the circuitbreaker are in synchronism, or with at leastone side dead to ensure that closing can bedone safely.
SESRSYN function includes a built-in voltageselection scheme for double bus arrangements.
Manual closing as well as automatic reclosingcan be checked by the function and can havedifferent settings.
For systems which are running asynchronousa synchronizing function is provided. Themain purpose of the synchronizing functionis to provide controlled closing of circuitbreakers when two asynchronous systems aregoing to be connected. It is used for slipfrequencies that are larger than those forsynchrocheck and lower than a set maximumlevel for the synchronizing function.
Autorecloser SMBRREC
The autorecloser (SMBRREC) functionprovides high-speed and/or delayed auto-reclosing for single breaker applications.
Up to five reclosing attempts can be includedby parameter setting.
The autoreclosing function can be configuredto co-operate with a synchrocheck function.
Autorecloser STBRREC
The autoreclosing function provides high-speed and/or delayed auto-reclosing forsingle breaker applications.
Up to five reclosing attempts can be includedby parameter setting. The first attempt can besingle- and/or three phase for single-phase ormulti-phase faults respectively.
Multiple autoreclosing functions are providedfor multi-breaker arrangements. A prioritycircuit allows one circuit breaker to close firstand the second will only close if the faultproved to be transient.
The autoreclosing function can be configuredto co-operate with a synchrocheck function.
Bay control QCBAY
The Bay control QCBAY function is usedtogether with Local remote and local remotecontrol functions is used to handle theselection of the operator place per bay.QCBAY also provides blocking functions thatcan be distributed to different apparatuseswithin the bay.
Local remote LOCREM /Localremote control LOCREMCTRL
The signals from the local HMI or from anexternal local/remote switch are applied viathe function blocks LOCREM andLOCREMCTRL to the Bay control (QCBAY)function block. A parameter in function blockLOCREM is set to choose if the switch signalsare coming from the local HMI or from anexternal hardware switch connected viabinary inputs.
Logic rotating switch for functionselection and LHMI presentationSLGGIO
The logic rotating switch for functionselection and LHMI presentation function(SLGGIO) (or the selector switch functionblock) is used to get a selector switchfunctionality similar to the one provided by ahardware selector switch. Hardware selectorswitches are used extensively by utilities, inorder to have different functions operating onpre-set values. Hardware switches arehowever sources for maintenance issues,lower system reliability and an extendedpurchase portfolio. The logic selectorswitches eliminate all these problems.
Selector mini switch VSGGIO
The Selector mini switch VSGGIO functionblock is a multipurpose function used for avariety of applications, as a general purposeswitch.
VSGGIO can be controlled from the menu orfrom a symbol on the single line diagram(SLD) on the local HMI.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
24 ABB
-
IEC 61850 generic communicationI/O functions DPGGIO
The IEC 61850 generic communication I/Ofunctions (DPGGIO) function block is used tosend double indications to other systems orequipment in the substation. It is especiallyused in the interlocking and reservationstation-wide logics.
Single point generic control 8signals SPC8GGIO
The Single point generic control 8 signals(SPC8GGIO) function block is a collection of8 single point commands, designed to bringin commands from REMOTE (SCADA) tothose parts of the logic configuration that donot need extensive command receivingfunctionality (for example, SCSWI). In thisway, simple commands can be sent directlyto the IED outputs, without confirmation.Confirmation (status) of the result of thecommands is supposed to be achieved byother means, such as binary inputs andSPGGIO function blocks. The commands canbe pulsed or steady.
AutomationBits AUTOBITS
The Automation bits function (AUTOBITS) isused to configure the DNP3 protocolcommand handling.
10. Schemecommunication
Scheme communication logic fordistance or overcurrent protectionZCPSCH
To achieve instantaneous fault clearance forall line faults, a scheme communication logicis provided. All types of communicationschemes for example, permissiveunderreaching, permissive overreaching,blocking, unblocking, intertrip are available.
Current reversal and weak-endinfeed logic for distance protectionZCRWPSCH
The current reversal function is used toprevent unwanted operations due to currentreversal when using permissive overreachprotection schemes in application withparallel lines when the overreach from thetwo ends overlap on the parallel line.
The weak-end infeed logic is used in caseswhere the apparent power behind theprotection can be too low to activate thedistance protection function. When activated,received carrier signal together with localunder voltage criteria and no reverse zoneoperation gives an instantaneous trip. Thereceived signal is also echoed back toaccelerate the sending end.
Current reversal and weak-endinfeed logic for distance protectionZCWSPSCH
The current reversal function is used toprevent unwanted operations due to currentreversal when using permissive overreachprotection schemes in application withparallel lines when the overreach from thetwo ends overlap on the parallel line.
The weak-end infeed logic is used in caseswhere the apparent power behind theprotection can be too low to activate thedistance protection function. When activated,received carrier signal together with localunder voltage criteria and no reverse zoneoperation gives an instantaneous trip. Thereceived signal is also echoed back toaccelerate the sending end.
Local acceleration logic ZCLCPLAL
To achieve fast clearing of faults on thewhole line, when no communication channelis available, local acceleration logic(ZCLCPLAL) can be used. This logic enablesfast fault clearing during certain conditions,but naturally, it can not fully replace acommunication channel.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 25
-
The logic can be controlled either by theautorecloser (zone extension) or by the loss-of-load current (loss-of-load acceleration).
Scheme communication logic forresidual overcurrent protectionECPSCH
To achieve fast fault clearance of earth faultson the part of the line not covered by theinstantaneous step of the residual overcurrentprotection, the directional residualovercurrent protection can be supported witha logic that uses communication channels.
In the directional scheme, information of thefault current direction must be transmitted tothe other line end. With directionalcomparison, a short operate time of theprotection including a channel transmissiontime, can be achieved. This short operatetime enables rapid autoreclosing functionafter the fault clearance.
The communication logic module fordirectional residual current protectionenables blocking as well as permissive under/overreaching schemes. The logic can also besupported by additional logic for weak-endinfeed and current reversal, included inCurrent reversal and weak-end infeed logicfor residual overcurrent protection(ECRWPSCH) function.
Current reversal and weak-endinfeed logic for residualovercurrent protection ECRWPSCH
The Current reversal and weak-end infeedlogic for residual overcurrent protectionECRWPSCH is a supplement to Schemecommunication logic for residual overcurrentprotection ECPSCH.
To achieve fast fault clearing for all earthfaults on the line, the directional earth-faultprotection function can be supported withlogic that uses communication channels.
The 650 series IEDs have for this reasonavailable additions to scheme communicationlogic.
If parallel lines are connected to commonbusbars at both terminals, overreachingpermissive communication schemes can tripunselectively due to fault current reversal.This unwanted tripping affects the healthyline when a fault is cleared on the other line.This lack of security can result in a total lossof interconnection between the two buses. Toavoid this type of disturbance, a fault currentreversal logic (transient blocking logic) canbe used.
Permissive communication schemes forresidual overcurrent protection can basicallyoperate only when the protection in theremote IED can detect the fault. Thedetection requires a sufficient minimumresidual fault current, out from this IED. Thefault current can be too low due to anopened breaker or high-positive and/or zero-sequence source impedance behind this IED.To overcome these conditions, weak-endinfeed (WEI) echo logic is used.
11. Logic
Tripping logic SMPPTRC
A function block for protection tripping isprovided for each circuit breaker involved inthe tripping of the fault. It provides the pulseprolongation to ensure a trip pulse ofsufficient length, as well as all functionalitynecessary for correct co-operation withautoreclosing functions.
The trip function block includes functionalityfor breaker lock-out.
Tripping logic SPTPTRC
A function block for protection tripping isprovided for each circuit breaker involved inthe tripping of the fault. It provides the pulseprolongation to ensure a trip pulse ofsufficient length, as well as all functionalitynecessary for correct cooperation withautoreclosing and communication logicfunctions.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
26 ABB
-
The trip function block includes functionalityfor evolving faults and breaker lock-out.
Trip matrix logic TMAGGIO
Trip matrix logic TMAGGIO function is usedto route trip signals and other logical outputsignals to different output contacts on the IED.
TMAGGIO output signals and the physicaloutputs allows the user to adapt the signalsto the physical tripping outputs according tothe specific application needs.
Configurable logic blocks
A number of logic blocks and timers areavailable for the user to adapt theconfiguration to the specific application needs.
OR function block.
INVERTER function blocks that inverts theinput signal.
PULSETIMER function block can be used,for example, for pulse extensions orlimiting of operation of outputs.
GATE function block is used for whetheror not a signal should be able to pass fromthe input to the output.
XOR function block.
LOOPDELAY function block used to delaythe output signal one execution cycle.
TIMERSET function has pick-up and drop-out delayed outputs related to the inputsignal. The timer has a settable time delay.
AND function block.
SRMEMORY function block is a flip-flopthat can set or reset an output from twoinputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block should be resetor return to the state before theinterruption, after a power interruption. Setinput has priority.
RSMEMORY function block is a flip-flopthat can reset or set an output from twoinputs respectively. Each block has twooutputs where one is inverted. The memorysetting controls if the block should be resetor return to the state before theinterruption, after a power interruption.Reset input has priority.
Boolean 16 to Integer conversionB16I
Boolean 16 to integer conversion function(B16I) is used to transform a set of 16 binary(logical) signals into an integer.
Boolean 16 to Integer conversionwith logic node representationB16IFCVI
Boolean 16 to integer conversion with logicnode representation function (B16IFCVI) isused to transform a set of 16 binary (logical)signals into an integer.
Integer to Boolean 16 conversionIB16A
Integer to boolean 16 conversion function(IB16A) is used to transform an integer into aset of 16 binary (logical) signals.
Integer to Boolean 16 conversionwith logic node representationIB16FCVB
Integer to boolean conversion with logicnode representation function (IB16FCVB) isused to transform an integer to 16 binary(logic) signals.
IB16FCVB function can receive remote valuesover IEC61850 depending on the operatorposition input (PSTO).
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 27
-
12. Monitoring
Measurements CVMMXN, CMMXU,VNMMXU, VMMXU, CMSQI, VMSQI
The measurement functions are used to get on-line information from the IED. These servicevalues make it possible to display on-lineinformation on the local HMI and on theSubstation automation system about:
measured voltages, currents, frequency,active, reactive and apparent power andpower factor
primary and secondary phasors current sequence components voltage sequence components
Event counter CNTGGIO
Event counter (CNTGGIO) has six counterswhich are used for storing the number oftimes each counter input has been activated.
Disturbance report DRPRDRE
Complete and reliable information aboutdisturbances in the primary and/or in thesecondary system together with continuousevent-logging is accomplished by thedisturbance report functionality.
Disturbance report DRPRDRE, alwaysincluded in the IED, acquires sampled data ofall selected analog input and binary signalsconnected to the function block that is,maximum 40 analog and 96 binary signals.
The Disturbance report functionality is acommon name for several functions:
Event list Indications Event recorder Trip value recorder Disturbance recorder Fault locator
The Disturbance report function ischaracterized by great flexibility regardingconfiguration, starting conditions, recordingtimes, and large storage capacity.
A disturbance is defined as an activation ofan input to the AxRADR or BxRBDR functionblocks, which are set to trigger thedisturbance recorder. All signals from start ofpre-fault time to the end of post-fault timewill be included in the recording.
Every disturbance report recording is savedin the IED in the standard Comtrade format.The same applies to all events, which arecontinuously saved in a ring-buffer. The localHMI is used to get information about therecordings. The disturbance report files maybe uploaded to PCM600 for further analysisusing the disturbance handling tool.
Event list DRPRDRE
Continuous event-logging is useful formonitoring the system from an overviewperspective and is a complement to specificdisturbance recorder functions.
The event list logs all binary input signalsconnected to the Disturbance report function.The list may contain up to 1000 time-taggedevents stored in a ring-buffer.
Indications DRPRDRE
To get fast, condensed and reliableinformation about disturbances in theprimary and/or in the secondary system it isimportant to know, for example binarysignals that have changed status during adisturbance. This information is used in theshort perspective to get information via thelocal HMI in a straightforward way.
There are three LEDs on the local HMI(green, yellow and red), which will displaystatus information about the IED and theDisturbance report function (trigged).
The Indication list function shows all selectedbinary input signals connected to theDisturbance report function that havechanged status during a disturbance.
Event recorder DRPRDRE
Quick, complete and reliable informationabout disturbances in the primary and/or inthe secondary system is vital, for example,time-tagged events logged during
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
28 ABB
-
disturbances. This information is used fordifferent purposes in the short term (forexample corrective actions) and in the longterm (for example functional analysis).
The event recorder logs all selected binaryinput signals connected to the Disturbancereport function. Each recording can containup to 150 time-tagged events.
The event recorder information is availablefor the disturbances locally in the IED.
The event recording information is anintegrated part of the disturbance record(Comtrade file).
Trip value recorder DRPRDRE
Information about the pre-fault and faultvalues for currents and voltages are vital forthe disturbance evaluation.
The Trip value recorder calculates the valuesof all selected analog input signals connectedto the Disturbance report function. The resultis magnitude and phase angle before andduring the fault for each analog input signal.
The trip value recorder information isavailable for the disturbances locally in theIED.
The trip value recorder information is anintegrated part of the disturbance record(Comtrade file).
Disturbance recorder DRPRDRE
The Disturbance recorder function suppliesfast, complete and reliable information aboutdisturbances in the power system. Itfacilitates understanding system behavior andrelated primary and secondary equipmentduring and after a disturbance. Recordedinformation is used for different purposes inthe short perspective (for example correctiveactions) and long perspective (for examplefunctional analysis).
The Disturbance recorder acquires sampleddata from selected analog- and binary signalsconnected to the Disturbance report function(maximum 40 analog and 96 binary signals).The binary signals available are the same asfor the event recorder function.
The function is characterized by greatflexibility and is not dependent on theoperation of protection functions. It canrecord disturbances not detected byprotection functions.
The disturbance recorder information for thelast 100 disturbances are saved in the IEDand the local HMI is used to view the list ofrecordings.
Measured value expander blockMVEXP
The current and voltage measurementsfunctions (CVMMXN, CMMXU, VMMXU andVNMMXU), current and voltage sequencemeasurement functions (CMSQI and VMSQI)and IEC 61850 generic communication I/Ofunctions (MVGGIO) are provided withmeasurement supervision functionality. Allmeasured values can be supervised with foursettable limits: low-low limit, low limit, highlimit and high-high limit. The measure valueexpander block has been introduced toenable translating the integer output signalfrom the measuring functions to 5 binarysignals: below low-low limit, below low limit,normal, above high-high limit or above highlimit. The output signals can be used asconditions in the configurable logic or foralarming purpose.
Fault locator LMBRFLO
The accurate fault locator is an essentialcomponent to minimize the outages after apersistent fault and/or to pin-point a weakspot on the line.
The fault locator is an impedance measuringfunction giving the distance to the fault inpercent, km or miles. The main advantage isthe high accuracy achieved by compensatingfor load current.
The compensation includes setting of theremote and local sources and calculation ofthe distribution of fault currents from eachside. This distribution of fault current,together with recorded load (pre-fault)currents, is used to exactly calculate the faultposition. The fault can be recalculated with
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 29
-
new source data at the actual fault to furtherincrease the accuracy.
Especially on heavily loaded long lines(where the fault locator is most important)where the source voltage angles can be up to35-40 degrees apart the accuracy can be stillmaintained with the advanced compensationincluded in fault locator.
Station battery supervisionSPVNZBAT
The station battery supervision functionSPVNZBAT is used for monitoring batteryterminal voltage.
SPVNZBAT activates the start and alarmoutputs when the battery terminal voltageexceeds the set upper limit or drops belowthe set lower limit. A time delay for theovervoltage and undervoltage alarms can beset according to definite time characteristics.
In the definite time (DT) mode, SPVNZBAToperates after a predefined operate time andresets when the battery undervoltage orovervoltage condition disappears.
Insulation gas monitoring functionSSIMG
Insulation gas monitoring function (SSIMG) isused for monitoring the circuit breakercondition. Binary information based on thegas pressure in the circuit breaker is used asinput signals to the function. In addition, thefunction generates alarms based on receivedinformation.
Insulation liquid monitoringfunction SSIML
Insulation liquid monitoring function (SSIML)is used for monitoring the circuit breakercondition. Binary information based on theoil level in the circuit breaker is used as inputsignals to the function. In addition, thefunction generates alarms based on receivedinformation.
Circuit breaker monitoring SSCBR
The circuit breaker condition monitoringfunction SSCBR is used to monitor different
parameters of the circuit breaker. Thebreaker requires maintenance when thenumber of operations has reached apredefined value. The energy is calculatedfrom the measured input currents as a sum of
Iyt values. Alarms are generated when thecalculated values exceed the thresholdsettings.
The function contains a blockingfunctionality. It is possible to block thefunction outputs, if desired.
13. Metering
Pulse counter logic PCGGIO
Pulse counter (PCGGIO) function countsexternally generated binary pulses, forinstance pulses coming from an externalenergy meter, for calculation of energyconsumption values. The pulses are capturedby the BIO (binary input/output) moduleand then read by the PCGGIO function. Ascaled service value is available over thestation bus.
Function for energy calculation anddemand handling ETPMMTR
Outputs from the Measurements (CVMMXN)function can be used to calculate energyconsumption. Active as well as reactivevalues are calculated in import and exportdirection. Values can be read or generated aspulses. Maximum demand power values arealso calculated by the function.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
30 ABB
-
14. Human Machineinterface
Local HMI
GUID-23A12958-F9A5-4BF1-A31B-F69F56A046C7 V2 EN
Figure 6. Local human-machine interface
The LHMI of the IED contains the followingelements:
Display (LCD) Buttons LED indicators Communication port
The LHMI is used for setting, monitoring andcontrolling .
The Local human machine interface, LHMIincludes a graphical monochrome LCD with aresolution of 320x240 pixels. The charactersize may vary depending on selectedlanguage. The amount of characters and rowsfitting the view depends on the character sizeand the view that is shown.
The LHMI can be detached from the mainunit. The detached LHMI can be wallmounted up to a distance of five meters fromthe main unit. The units are connected withthe Ethernet cable included in the delivery.
The LHMI is simple and easy to understand.The whole front plate is divided into zones,each with a well-defined functionality:
Status indication LEDs Alarm indication LEDs which can
indicate three states with the colorsgreen, yellow and red, with userprintable label. All LEDs are configurablefrom the PCM600 tool
Liquid crystal display (LCD) Keypad with push buttons for control
and navigation purposes, switch forselection between local and remotecontrol and reset
Five user programmable function buttons An isolated RJ45 communication port for
PCM600
15. Basic IED functions
Self supervision with internal eventlist
The Self supervision with internal event list(INTERRSIG and SELFSUPEVLST) functionreacts to internal system events generated bythe different built-in self-supervisionelements. The internal events are saved in aninternal event list.
Time synchronization
Use time synchronization to achieve acommon time base for the IEDs in aprotection and control system. This makescomparison of events and disturbance databetween all IEDs in the system possible.
Time-tagging of internal events anddisturbances are an excellent help whenevaluating faults. Without timesynchronization, only the events within theIED can be compared to one another. Withtime synchronization, events anddisturbances within the entire station, andeven between line ends, can be compared atevaluation.
In the IED, the internal time can besynchronized from a number of sources:
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 31
-
SNTP IRIG-B DNP IEC60870-5-103
Parameter setting groups ACTVGRP
Use the four sets of settings to optimize theIED operation for different system conditions.Creating and switching between fine-tunedsetting sets, either from the local HMI orconfigurable binary inputs, results in a highlyadaptable IED that can cope with a variety ofsystem scenarios.
Test mode functionality TESTMODE
The protection and control IEDs have manyincluded functions. To make the testingprocedure easier, the IEDs include the featurethat allows individual blocking of a single-,several-, or all functions.
There are two ways of entering the test mode:
By configuration, activating an inputsignal of the function block TESTMODE
By setting the IED in test mode in thelocal HMI
While the IED is in test mode, all functionsare blocked.
Any function can be unblocked individuallyregarding functionality and event signaling.This enables the user to follow the operationof one or several related functions to checkfunctionality and to check parts of theconfiguration, and so on.
Change lock function CHNGLCK
Change lock function (CHNGLCK) is used toblock further changes to the IEDconfiguration and settings once thecommissioning is complete. The purpose is toblock inadvertent IED configuration changesbeyond a certain point in time.
Authority status ATHSTAT
Authority status (ATHSTAT) function is anindication function block for user log-onactivity.
Authority check ATHCHCK
To safeguard the interests of our customers,both the IED and the tools that are accessingthe IED are protected, by means ofauthorization handling. The authorizationhandling of the IED and the PCM600 isimplemented at both access points to the IED:
local, through the local HMI remote, through the communication ports
16. Stationcommunication
IEC 61850-8-1 communicationprotocol
The IED supports the communicationprotocols IEC 61850-8-1 and DNP3 over TCP/IP. All operational information and controlsare available through these protocols.However, some communication functionality,for example, horizontal communication(GOOSE) between the IEDs, is only enabledby the IEC 61850-8-1 communication protocol.
The IED is equipped with an optical Ethernetrear port for the substation communicationstandard IEC 61850-8-1. IEC 61850-8-1protocol allows intelligent electrical devices(IEDs) from different vendors to exchangeinformation and simplifies systemengineering. Peer-to-peer communicationaccording to GOOSE is part of the standard.Disturbance files uploading is provided.
Disturbance files are accessed using the IEC61850-8-1 protocol. Disturbance files areavailable to any Ethernet based applicationvia FTP in the standard Comtrade format.Further, the IED can send and receive binaryvalues, double point values and measuredvalues (for example from MMXU functions),together with their quality, using the IEC61850-8-1 GOOSE profile. The IED meets theGOOSE performance requirements for
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
32 ABB
-
tripping applications in substations, asdefined by the IEC 61850 standard. The IEDinteroperates with other IEC 61850-compliantIEDs, tools, and systems and simultaneouslyreports events to five different clients on theIEC 61850 station bus.
The event system has a rate limiter to reduceCPU load. The event channel has a quota of10 events/second. If the quota is exceededthe event channel transmission is blockeduntil the event changes is below the quota,no event is lost.
All communication connectors, except for thefront port connector, are placed on integratedcommunication modules. The IED isconnected to Ethernet-based communicationsystems via the fibre-optic multimode LCconnector (100BASE-FX).
The IED supports SNTP and IRIG-B timesynchronization methods with a time-stamping resolution of 1 ms.
Ethernet based: SNTP and DNP3 With time synchronization wiring: IRIG-B
The IED supports IEC 60870-5-103 timesynchronization methods with a timestamping resolution of 5 ms.
Table 1. Supported communicationinterface and protocol alternatives
Interfaces/Protocols
Ethernet100BASE-
FX LC
STconnector
IEC61850-8-1
DNP3
IEC60870-5-103
= Supported
Horizontal communication viaGOOSE for interlocking
GOOSE communication can be used forexchanging information between IEDs via theIEC 61850-8-1 station communication bus.
This is typically used for sending apparatusposition indications for interlocking orreservation signals for 1-of-n control. GOOSEcan also be used to exchange any boolean,integer, double point and analog measuredvalues between IEDs.
DNP3 protocol
DNP3 (Distributed Network Protocol) is a setof communications protocols used tocommunicate data between components inprocess automation systems. For a detaileddescription of the DNP3 protocol, see theDNP3 Communication protocol manual.
IEC 60870-5-103 communicationprotocol
IEC 60870-5-103 is an unbalanced (master-slave) protocol for coded-bit serialcommunication exchanging information witha control system, and with a data transfer rateup to 38400 bit/s. In IEC terminology, aprimary station is a master and a secondarystation is a slave. The communication isbased on a point-to-point principle. Themaster must have software that can interpretIEC 60870-5-103 communication messages.
17. Hardware description
Layout and dimensions
Mounting alternatives
The following mounting alternatives areavailable (IP40 protection from the front):
19 rack mounting kit Wall mounting kit Flush mounting kit 19" dual rack mounting kit
See ordering for details about availablemounting alternatives.
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 33
-
Flush mounting the IED
H
I
K
J
C
F
G
B
A
ED
IEC09000672.ai
IEC09000672 V1 EN
Figure 7. Flush mounting the IED into a panelcut-out
A 240 mm G 21.55 mm
B 21.55 mm H 220 mm
C 227 mm I 265.9 mm
D 228.9 mm J 300 mm
E 272 mm K 254 mm
F 6 mm
A
B
C
IEC09000673.ai
IEC09000673 V1 EN
Figure 8. Flush mounted IED
A 222 mm
B 27 mm
C 13 mm
Rack mounting the IED
A C
B
E
D
IEC09000676.ai
IEC09000676 V1 EN
Figure 9. Rack mounted IED
A 224 mm + 12 mm with ring-lug connector
B 25.5 mm
C 482.6 mm (19")
D 265.9 mm (6U)
E 13 mm
A
BC
E
D
IEC09000677.ai
IEC09000677 V1 EN
Figure 10. Two rack mounted IEDs side by side
A 224 mm + 12 mm with ring-lug connector
B 25.5 mm
C 482.6 mm (19")
D 13 mm
E 265.9 mm (6U)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
34 ABB
-
Wall mounting the IED
C
F
G
B
A
ED
IEC09000678.ai
IEC09000678 V1 EN
Figure 11. Wall mounting the IED
A 270 mm E 190.5 mm
B 252.5 mm F 296 mm
C 6.8 mm G 13 mm
D 268.9 mm
GUID-5C185EAC-13D0-40BD-8511-58CA53EFF7DE V1 EN
Figure 12. Main unit and detached LHMIdisplay
A 25.5 mm E 258.6 mm
B 220 mm F 265.9 mm
C 13 mm G 224 mm
D 265.9 mm
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 35
-
18. Connection diagrams
1MRK006501-HB 2 PG 1.1 IEC V1 EN
Figure 13. Designation for 6U, 1/2x19" casingwith 1 TRM
Module Slot Rear Position
COM pCOM X0, X1, X4, X9,X304
PSM pPSM X307, X309, X410
TRM p2 X101, X102
BIO p3 X321, X324
BIO p4 X326, X329
BIO p5 X331, X334
BIO p6 X336, X339
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
36 ABB
-
Connection diagrams for REL650 A01
1MRK006501-HB 3 PG 1.1 IEC V1 EN
Figure 14. Communication module (COM)
1MRK006501-HB 4 PG 1.1 IEC V1 EN
Figure 15. Power supply module (PSM)48-125V DC
1MRK006501-HB 5 PG 1.1 IEC V1 EN
Figure 16. Power supply module (PSM),110-250V DC
1MRK006501-HB 6 PG 1.1 IEC V1 EN
Figure 17. Transformer module (TRM)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 37
-
1MRK006501-HB 7 PG 1.1 IEC V1 EN
Figure 18. Binary input/output (BIO) option(Terminal X321, X324)
1MRK006501-HB 8 PG 1.1 IEC V1 EN
Figure 19. Binary input/output (BIO) option(Terminal X326, X329)
Connection diagrams for REL650 A05
1MRK006501-TB 3 PG 1.1 IEC V1 EN
Figure 20. Communication module (COM)
1MRK006501-TB 4 PG 1.1 IEC V1 EN
Figure 21. Power supply module (PSM)48-125V DC
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
38 ABB
-
1MRK006501-TB 5 PG 1.1 IEC V1 EN
Figure 22. Power supply module (PSM),110-250V DC
1MRK006501-TB 6 PG 1.1 IEC V1 EN
Figure 23. Transformer module (TRM)
1MRK006501-TB 7 PG 1.1 IEC V1 EN
Figure 24. Binary input/output (BIO) option(Terminal X321, X324)
1MRK006501-TB 8 PG 1.1 IEC V1 EN
Figure 25. Binary input/output (BIO) option(Terminal X326, X329)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 39
-
Connection diagrams for REL650 A11
1MRK006501-KB 3 PG 1.1 IEC V1 EN
Figure 26. Communication module (COM)
1MRK006501-KB 4 PG 1.1 IEC V1 EN
Figure 27. Power supply module (PSM)48-125V DC
1MRK006501-KB 5 PG 1.1 IEC V1 EN
Figure 28. Power supply module (PSM),110-250V DC
1MRK006501-KB 6 PG 1.1 IEC V1 EN
Figure 29. Transformer module (TRM)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
40 ABB
-
1MRK006501-KB 7 PG 1.1 IEC V1 EN
Figure 30. Binary input/output (BIO) option(Terminal X321, X324)
1MRK006501-KB 8 PG 1.1 IEC V1 EN
Figure 31. Binary input/output (BIO) option(Terminal X326, X329)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 41
-
19. Technical data
General
Definitions
Referencevalue
The specified value of an influencing factor to which are referred thecharacteristics of the equipment
Nominalrange
The range of values of an influencing quantity (factor) within which, underspecified conditions, the equipment meets the specified requirements
Operativerange
The range of values of a given energizing quantity for which the equipment,under specified conditions, is able to perform its intended functionsaccording to the specified requirements
Energizing quantities, rated valuesand limits
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
42 ABB
-
Analog inputs
Table 2. Energizing inputs
Description Value
Rated frequency 50/60 Hz
Operating range Rated frequency 5 Hz
Current inputs Rated current, In 0.1/0.5 A1) 1/5 A2)
Thermal withstandcapability:
Continuously 4 A 20 A
For 1 s 100 A 500 A
For 10 s 20 A 100 A
Dynamic currentwithstand:
Half-wave value 250 A 1250 A
Input impedance
-
Auxiliary DC voltage
Table 3. Power supply
Description Type 1 Type 2
Uauxnominal 100, 110, 120, 220, 240 VAC, 50 and 60 Hz
48, 60, 110, 125 V DC
110, 125, 220, 250 V DC
Uauxvariation 85...110% of Un (85...264 V
AC)
80...120% of Un (38.4...150 V
DC)
80...120% of Un (88...300 V
DC)
Maximum load of auxiliaryvoltage supply
35 W
Ripple in the DC auxiliaryvoltage
Max 15% of the DC value (at frequency of 100 Hz)
Maximum interruption time inthe auxiliary DC voltagewithout resetting the IED
50 ms at Uaux
Binary inputs and outputs
Table 4. Binary inputs
Description Value
Operating range Maximum input voltage 300 V DC
Rated voltage 24...250 V DC
Current drain 1.6...1.8 mA
Power consumption/input
-
Table 5. Signal output and IRF output
IRF relay change over - type signal output relay
Description Value
Rated voltage 250 V AC/DC
Continuous contact carry 5 A
Make and carry for 3.0 s 10 A
Make and carry 0.5 s 30 A
Breaking capacity when the control-circuittime constant L/R
-
Table 8. Ethernet interfaces
Ethernet interface Protocol Cable Data transfer rate
LAN/HMI port (X0)1) - CAT 6 S/FTP or better 100 MBits/s
LAN1 (X1) TCP/IP protocol Fibre-optic cablewith LC connector
100 MBits/s
1) Only available for the external HMI option.
Table 9. Fibre-optic communication link
Wave length Fibre type Connector Permitted path
attenuation1)Distance
1300 nm MM 62.5/125m glassfibre core
LC
-
Table 14. Environmental conditions
Description Value
Operating temperature range -25...+55C (continuous)
Short-time service temperature range -40...+70C (
-
Type tests according to standards
Table 16. Electromagnetic compatibility tests
Description Type test value Reference
100 kHz and 1 MHz burstdisturbance test
IEC 61000-4-18IEC 60255-22-1, level 3
Common mode 2.5 kV
Differential mode 1.0 kV
Electrostatic discharge test IEC 61000-4-2IEC 60255-22-2, level 4
Contact discharge 8 kV
Air discharge 15 kV
Radio frequency interferencetests
Conducted, common mode 10 V (emf), f=150 kHz...80MHz
IEC 61000-4-6IEC 60255-22-6, level 3
Radiated, amplitude-modulated
20 V/m (rms), f=80...1000MHz and f=1.4...2.7 GHz
IEC 61000-4-3IEC 60255-22-3, level 3
Fast transient disturbancetests
IEC 61000-4-4IEC 60255-22-4, class A
Communication ports 2 kV
Other ports 4 kV
Surge immunity test IEC 61000-4-5IEC 60255-22-5, level 3/2
Communication 1 kV line-to-earth
Other ports 2 kV line-to-earth, 1 kV line-to-line
Power frequency (50 Hz)magnetic field
IEC 61000-4-8, level 5
3 s 1000 A/m
Continuous 100 A/m
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
48 ABB
-
Table 16. Electromagnetic compatibility tests, continued
Description Type test value Reference
Power frequency immunitytest
Common mode
Differential mode
300 V rms 150 V rms
IEC 60255-22-7, class AIEC 61000-4-16
Voltage dips and shortinterruptions
Dips:40%/200 ms70%/500 msInterruptions:0-50 ms: No restart0... s : Correct behaviour atpower down
IEC 60255-11IEC 61000-4-11
Electromagnetic emissiontests
EN 55011, class AIEC 60255-25
Conducted, RF-emission(mains terminal)
0.15...0.50 MHz < 79 dB(V) quasi peak< 66 dB(V) average
0.5...30 MHz < 73 dB(V) quasi peak< 60 dB(V) average
Radiated RF-emission
30...230 MHz < 40 dB(V/m) quasi peak,measured at 10 m distance
230...1000 MHz < 47 dB(V/m) quasi peak,measured at 10 m distance
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 49
-
Table 17. Insulation tests
Description Type test value Reference
Dielectric tests: IEC 60255-5
Test voltage 2 kV, 50 Hz, 1 min1 kV, 50 Hz, 1 min,communication
Impulse voltage test: IEC 60255-5
Test voltage 5 kV, unipolar impulses,waveform 1.2/50 s, sourceenergy 0.5 J1 kV, unipolar impulses,waveform 1.2/50 s, sourceenergy 0.5 J, communication
Insulation resistancemeasurements
IEC 60255-5
Isolation resistance >100 M, 500 V DC
Protective bonding resistance IEC 60255-27
Resistance
-
EMC compliance
Table 20. EMC compliance
Description Reference
EMC directive 2004/108/EC
Standard EN 50263 (2000)EN 60255-26 (2007)
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 51
-
Impedance protection
Table 21. Distance measuring zone, Quad ZQDPDIS
Function Range or value Accuracy
Number of zones 5 with selectabledirection
-
Minimum operateresidual current
(5-30)% of IBase 1,0 % of I r
Minimum operate current,phase-to-phase and phase-to-earth
(10-30)% of IBase 1,0 % of I r
Positive sequenceimpedance reach forzones
0.005 - 3000.000 5.0% static accuracy 2.0 degrees static angular accuracyConditions:Voltage range: (0.1-1.1) x UrCurrent range: (0.5-30) x IrAngle: at 0 degrees and 85 degrees
Fault resistance, phase-to-earth
(1.00-9000.00) /loop
Fault resistance, phase-to-phase
(1.00-3000.00) /loop
Line angle for zones (0 - 180) degrees
Magnitude of earth returncompensation factor KNfor zones
0.00 - 3.00 -
Angle for earth returncompensation factor KNfor zones
(-180 - 180)degrees
-
Dynamic overreach
-
Table 22. Phase selection with load encroachment, quadrilateral characteristicFDPSPDIS
Function Range or value Accuracy
Minimum operate current (5-500)% of IBase 1.0% of Ir
Reactive reach, positivesequence
(0.503000.00) 2.0% static accuracyConditions:Voltage range: (0.1-1.1) x UrCurrent range: (0.5-30) x IrAngle: at 0 degrees and 85 degrees
Reactive reach, zerosequence, forward andreverse
(0.50 - 3000.00)
Fault resistance, phase-to-earth faults, forward andreverse
(1.009000.00) /loop
Fault resistance, phase-to-phase faults, forward andreverse
(0.503000.00) /loop
Load encroachmentcriteria:Load resistance, forwardand reverseSafety load impedanceangle
(1.003000.00) /phase(5-70) degrees
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 53
-
Table 23. Full-scheme distance protection, Mho characteristic ZMOPDIS
Function Range or value Accuracy
Number of zones withselectable directions
5 with selectabledirection
-
Minimum operate current,phase-to-earth
(1030)% of IBase 2.0% of Ir
Minimum operate current,phase-to-phase
(10-30)% of IBase -13% of set value 2.0% of Ir
Positive sequenceimpedance
(0.0053000.000) W/phase
2.0% static accuracyConditions:Voltage range: (0.1-1.1) x UrCurrent range: (0.5-30) x IrAngle: at 0 degrees and 85 degrees
Reverse positive sequenceimpedance
(0.0053000.000) /phase
Impedance reach forphase-to-phase elements
(0.0053000.000) /phase
Angle for positivesequence impedance,phase-to-phase elements
(1090) degrees
Reverse reach of phase-to-phase loop
(0.0053000.000) /phase
Magnitude of earth returncompensation factor KN
(0.003.00)
Angle for earthcompensation factor KN
(-180180) degrees
Dynamic overreach
-
Table 25. Phase preference logic PPLPHIZ
Function Range or value Accuracy
Operate value, phase-to-phase and phase-to-neutral undervoltage
(10.0 - 100.0)% of UBase 0,5% of Ur
Reset ratio, undervoltage < 105% -
Operate value, residualvoltage
(5.0 - 300.0)% of UBase 0,5% of Ur
Reset ratio, residualvoltage
> 95% -
Operate value, residualcurrent
(10 - 200)% of IBase 1,0% of Ir for I < Ir 1,0% of I for I > Ir
Reset ratio, residualcurrent
> 95% -
Timers (0.000 - 60.000) s 0,5% 10 ms
Operating mode No Filter, NoPrefCyclic: 1231c, 1321cAcyclic: 123a, 132a, 213a,231a, 312a, 321a
Table 26. Power swing detection ZMRPSB
Function Range or value Accuracy
Reactive reach (0.10-3000.00) W
2.0% static accuracyConditions:Voltage range: (0.1-1.1) x UrCurrent range: (0.5-30) x IrAngle: at 0 degrees and 85 degreesResistive reach (0.101000.00)W
Timers (0.000-60.000) s 0.5% 25 ms
Minimum operate current (5-30) of IBase 1% of Ir
Line distance protection REL650 1MRK 506 328-BEN -Product version: 1.1 Issued: February 2011
ABB 55
-
Table 27. Automatic switch onto fault logic, voltage and current based ZCVPSOF
Parameter Range orvalue
Accuracy
Operate voltage, detection of dead line (1100)% ofUBase
0.5% of Ur
Reset ratio, operate vol