dn110 - hutterer & lechner

Ø 354

Ø 203

DN110

101

Ø 160

1313. Floor

HL Drains

164

HL Floor drains

Basic information about design and installation

Relevant standards/directivesÖNORM B2501 .............Drainage of buildingsDIN 1986-100 ................Drainage systems for buildings and estatesEN 12056 .......................Gravity drainage systems inside of buildingsÖNORM B2207 .............Tiling worksEN1253 ..........................Drains for buildings

Floor drains serve as central drainage of floor surfaces. To reach a satisfying result, aesthe-tical and functional, the plumber has to care for some important topics. The coordination of the different craftsmen (designer, construc-tion company, plumber, tiler..) is the biggest challange for the plumber. Therefore please notice allready during planning and design, some topics:

▲ Function: The question, how the drain is finally used, decides allready during design of the drainage system the choise of the gully. Generally one differs between permanent use (places, where splashing water occures, e.g. shower) and irregular use (e.g. as savety drain in laundry rooms). ▲ Stench trap: Especially at rarely used drain spots one has to avoid, that stench rises from the sewage system. A classic solution is to use a drain with additional side inlet (HL300, HL304). A regularely used drain spot (e.g. washing basin) makes sure, that the trap cannot become dry. In this case the drain should be constructed backwater save, so that the wastewater from the basin cannot overflow on the floor. Also the inlet should be siphoned in the drain itself. Another solution for this problem is the wellknown drain-series „Primus“ of HL. These drains have a normal water siphon and a mechanical trap. A floating body is part of a normal water trap. When the water evaporates in the trap (or is sucked out by vacuum in the sewage system), the floating body sinks on the mouth of the drain and closes it.

▲ Capacity: The test procedure for evaluating the drain capacity for floor drains is made according EN 1253-2:2004 with 20mm impounded water above the grate. If floor drains are used for barriere-free showers, the plumber should take care, that the flow rate is higher than the water inlet from the shower, to avoid water running into the dry area of the bathroom.

▲ Waterproofing: To avoid leakage water to get into the floor construction, the floor drain has to be con-nected to the on-site waterproofing. Attention: Gaps between tiles are not waterproof! In most cases the waterproofing (mostly liquid compounds) is located directly under the tiles. HL floor drains are equiped with flanges, on which the plumber may install the right sealing kit. The installer, together with the tiler, should decide, which. To apply the waterproofing material directly on the flange, is not water-proof.

▲ Sound protection: Please see chapter „accessories“ on page 256

▲ Installation: When the floor drain is mounted, the level of the flange should be below the level of the screed, so that a sufficiant incline to the drain is possible. Attention: The height of the drain body is not the minimum height of the screed.

▲ Design: Depending on taste and function, you may chose different types of grates and extensions. The plumber should first talk to the enduser, which one he prefers, as a subsequent change is not allways possible.

165

Selection of the convenient drain

Selective criteria Requirements Product

horizontal outlet vertical outlet

Capacity To find the right choise, one has to know, which maximum wastewater quantity should be drained off.

up to 0,4 l/s → HL90PrD up to 0,43 l/s → HL90Pr (-3000) up to 0,5 l/s → Series HL510N, Series HL80.1, HL541(I)Series HL300, HL304 up to 0,8 l/s → HL540(I), HL5100Pr up to 1 l/s → HL5100 up to 1,12 l/s → Series HL70 up to 1,5 l/s → HL72.1(N)

up to 0,5 l/s → Series HL80,Series HL310NPr up to 0,67 l/s → Series HL310N up to 0,8 l/s → HL3100Pr from 1,25 l/s up to 1,4 l/s → HL3100 up to 1,8 l/s → Series HL317

Existing floor height

At drains with horizontal outlet the floor height is an important criteria.

Floor construction concrete floor - top edge of the screed≥ 70 mm ≤ 90 mm≥ 90 mm ≤ 110 mm≥ 90 mm ≤ 250 mm≥ 110 mm ≤ 160 mm≥ 160 mm ≤ 180 mm≥ 180 mm

At drains with vertical outlet the drain body lies on the concrete floor and therefore mostly needs an extension element with flange, to reach the top edge of the screed.

Height of the drain body: Series HL90, HL541(i) = 62 mmSeries HL510N = 79 mm,Series HL540 = 80 mmSeries HL5100 = 97 mmSeries HL72.1 = 150 mmSeries HL70 = 173 mm

Series HL80, HL310N → HL85N Series HL3100 → HL8500 Series HL317 → HL350.1

Waterproofing The use of a sealing kit, which fits to the on-site waterproofing, is absolutely neccessary for a watertight connection. Kind and material of the waterproofing:For under-tile waterproofings, e.g.2-component-epoxy resins

For EPDM-sheetings, based on bitumen, for bitumen coatings and for welding of bitumen sheetings

Welding of bitumen sheetings

Series HL70, HL80, HL90, HL300, HL310N, HL510N → HL83.MSeries HL72.1 and HL317 → HL84.MHL540 and HL541 series → Waterproofing included!Series HL3100 and HL5100 → HL8300.M

Series HL70, HL80, HL90, HL300, HL310N, HL510N → HL83Series HL72.1 and HL317 → HL84 Series HL3100 and HL5100 → HL8300

HL83H, HL8300.HSeries HL70......→ HL83HInstead of series HL72.1 or HL317 → HL72.1H and HL317HSeries HL3100 and HL5100 → HL8300H

166

HL85N

HL Floor drains – Sectional drawings

HL510NPr-3020Floor drain with tilable grate

HL310NPr-3000Floor drain with Primus-trap and stainless steel frame

Impact sound insulation

ScreedEpoxy resin coating

HL80.1C Ablauf

Concrete floor

Floor drains with Epoxy resin coating


Concrete floor HL310NPr-3000

HL340N

ScreedWaterproofingHL83.M Sealing kitTile glueTile layer

Tiled floorUnder-tile waterproofing

HL510N-3000

ScreedWaterproofingTile glueTile layer

Sound protection pad HL6200


HL510NPr-3020

HL85N

Tile layer Tile glue Waterproofing Screed

HL510N-3000Floor drain with stainless steel grate

Sound protection pad HL6200


HL80.1CDrain with polymere concrete collar and ball-joint outlet

HL83.M Sealing kit

HL83.M Sealing kit

HL540 Sectional drawing and installation see page 40/44

HL510N-3000

HL510NPr-3020

HL80.1C

HL310NPr-3000

167

HL Floor drains – Installation

1. Fill in concrete and level to the height of the lid cover 2. Wait, until the concrete is set

3. Remove lid cover, clean flange and insert the gasket

5. Fix the stainless steel ring by screwing 6. The sealing kit is below the concrete level4. Apply the waterproofing membrane

7. Apply the liquid waterproofing 8. Smooth the membrane 9. Apply the liquid waterproofing on the whole wet area.

10. The sealing kit is completely below the concrete level

11. Cut the extension 12. Insert the extension without O-ring. Lay the tiles.

168

HL Floor drains – Products – Overview HL Floor drains – Products – Overview

Product HL90Pr HL90PrD HL510N(Pr) HL80.1 HL80.1C HL90Pr-3020 HL300 HL510N(Pr)-3020 HL5100(Pr) HL310N(Pr)-3020 HL72.1N HL310N(Pr) HL3100(Pr) HL317

Description Drain horizontalDN40/50

Drain horizontal DN40, with fleece flange

Drain horizontal DN40/50

Drain 50/75 with convertable ball-joint outlet

Drain 50/75 with polymere concrete collar and converta-ble outlet


Drain horizontal DN50 with side inlet


Floor drain horizontal DN50/75, high capacity

Drain vertikal DN50/75/110 Floor drain horizontal DN75/110, high capacity

Floor drain verticalDN50/75/110

Ablauf senkrechtDN50/75/110

Floor drain verticalDN50/75/110/160

Function Extremly flat, for flat floor constructions with PRIMUS trap

Especially for under-tile waterproofings, with PRIMUS trap

Standard drain, flat, also availa-ble with PRIMUS trap

For horizontal and vertical connection

Especially for epoxy resin floor surfaces

Extreme flat with tilable grate and PRIMUS trap

With side inlet, which cares for a full water trap. The integrated backwater protector prefents foam to leak through the grate.

Standard drain with tilable extension and optional PRIMUS trap

For high capacity reasons, also available with PRIMUS trap

With tilable grate and optional PRIMUS trap

For high capacity reasons

For outlet pipes below the concrete floor, also available with PRIMUS trap

For outlet pipes below the concrete floor, with high capacity, also available with PRIMUS trap

For outlet pipes below the concrete floor, with high capacity.

Product HL340N HL3400 HL350 HL85N HL8500 HL350.1(.0) HL350.1H HL85NC HL3200

Description Extension Extension Extension Extension with flange Extension with flange Extension with Sealing flange

Extension with bitumen flange Extension with polymere concrete collar Extension with stainless steel frame and grate

Function For elongating the extension, fits to drains of series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

For elongating the extension, fits to drains of series HL3100 and HL5100

For elongating the exten-sion, fits to drains of series HL72.1 and HL317

For the adjustment of the drain to the waterproofing level, fits to drains of series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

For the adjustment of the drain to the waterproo-fing level, fits to drains of series HL3100 and HL5100

To adjust the drain to the waterproofing level, fitting to floor drain series HL72.1 and HL317

To adjust the drain to the level of under-tile waterproofings, fitting to floor drain series HL72.1 and HL317

For height adjustment of the drain to liquid waterproofings, fits to drain series HL90,HL510N,HL80, HL300, HL70, HL310N and HL304

To change from standard extension to ex-tension with stainless steel frame, e.g. when you use „design“-grates. Fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Product data see chapter sealing kits / extensions

Drains

Extensions

HL90Pr HL90PrD HL510N(Pr) HL80.1 HL80.1C HL90Pr-3020 HL300 HL510N(Pr)-3020 HL5100(Pr) HL310N(Pr)-3020 HL72.1N HL310N(Pr) HL3100(Pr) HL317

HL340N HL3400 HL350 HL85N HL8500 HL350.1(.0) HL350.1H HL85NC HL3200

169


Product HL90Pr HL90PrD HL510N(Pr) HL80.1 HL80.1C HL90Pr-3020 HL300 HL510N(Pr)-3020 HL5100(Pr) HL310N(Pr)-3020 HL72.1N HL310N(Pr) HL3100(Pr) HL317

Description Drain horizontalDN40/50

Drain horizontal DN40, with fleece flange


Drain 50/75 with convertable ball-joint outlet

Drain 50/75 with polymere concrete collar and converta-ble outlet


Drain horizontal DN50 with side inlet


Floor drain horizontal DN50/75, high capacity

Drain vertikal DN50/75/110 Floor drain horizontal DN75/110, high capacity

Floor drain verticalDN50/75/110

Ablauf senkrechtDN50/75/110

Floor drain verticalDN50/75/110/160

Function Extremly flat, for flat floor constructions with PRIMUS trap

Especially for under-tile waterproofings, with PRIMUS trap

Standard drain, flat, also availa-ble with PRIMUS trap

For horizontal and vertical connection

Especially for epoxy resin floor surfaces

Extreme flat with tilable grate and PRIMUS trap

With side inlet, which cares for a full water trap. The integrated backwater protector prefents foam to leak through the grate.

Standard drain with tilable extension and optional PRIMUS trap

For high capacity reasons, also available with PRIMUS trap

With tilable grate and optional PRIMUS trap

For high capacity reasons

For outlet pipes below the concrete floor, also available with PRIMUS trap

For outlet pipes below the concrete floor, with high capacity, also available with PRIMUS trap

For outlet pipes below the concrete floor, with high capacity.

Product HL340N HL3400 HL350 HL85N HL8500 HL350.1(.0) HL350.1H HL85NC HL3200

Description Extension Extension Extension Extension with flange Extension with flange Extension with Sealing flange

Extension with bitumen flange Extension with polymere concrete collar Extension with stainless steel frame and grate

Function For elongating the extension, fits to drains of series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

For elongating the extension, fits to drains of series HL3100 and HL5100

For elongating the exten-sion, fits to drains of series HL72.1 and HL317

For the adjustment of the drain to the waterproofing level, fits to drains of series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

For the adjustment of the drain to the waterproo-fing level, fits to drains of series HL3100 and HL5100

To adjust the drain to the waterproofing level, fitting to floor drain series HL72.1 and HL317

To adjust the drain to the level of under-tile waterproofings, fitting to floor drain series HL72.1 and HL317

For height adjustment of the drain to liquid waterproofings, fits to drain series HL90,HL510N,HL80, HL300, HL70, HL310N and HL304

To change from standard extension to ex-tension with stainless steel frame, e.g. when you use „design“-grates. Fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

HL90Pr HL90PrD HL510N(Pr) HL80.1 HL80.1C HL90Pr-3020 HL300 HL510N(Pr)-3020 HL5100(Pr) HL310N(Pr)-3020 HL72.1N HL310N(Pr) HL3100(Pr) HL317

HL340N HL3400 HL350 HL85N HL8500 HL350.1(.0) HL350.1H HL85NC HL3200

170


Accessories

Product HL3020 HL37N HL3000 HL37NP HL38N HL39G HL3910 HL3911 HL66(Q) HL3928 HL3120 HL3121 HL3123 HL3124 HL3125 HL3127

Description Tilable extension Standard extension

Extension „Klick-Klack“

Extension with PVC-collar

Round extension Cast iron exten-sion


Extension „Klick-Klack“ with screwable grate

Extension Extension with design-grate „Hamam“

Design-grate „Quadra“

Design-grate „Seine“

Design-grate „Orinoco“

Design-grate „Nil“ Design-grate „Yukon“

Design-grate „Primus Design“

Function Extension fits to drain bodies HL70K-3020, HL80K-3020, HL90K-3020, HL300K-3020, HL304K-3020, HL310NK-3020 and HL510NK-3020

Standard exten-sion, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Standard extension with stainless steel frame, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

To connect PVC floor coverings, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Extension with round cover plate, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Usage with high load or to con-nect hot bitumen floor coverings, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Standard exten-sion, fitting to floor drain series HL3100 and HL5100


Stainless steel grate with high request on design and stability, fitting to floor drain series HL72.1 and HL317

Extension for floor drain with golden frame and grate, design „Hamam“. Fits to floor drain series HL5100 and HL3100.

Stainless steel grate with high request on design and stability, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304






Product data see chapter sealing kits / extensions

Sealing kits

Product HL83.0 HL83 HL83.M HL83.H HL8300.0 HL8300 HL8300.M HL8300.H HL84.0 HL84 HL84.M

Description Sealing kit without sheeting Sealing kit with EPDM sheeting

Sealing kit with textile coated membrane

Sealing kit with bitumen collar Sealing kit without sheeting Sealing kit with EPDM sheeting


Sealing kit with bitumen collar

Sealing kit without sheeting Sealing kit with EPDM sheeting


Function For clamping of on-site sheetings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For under-tile waterproofings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For bitumen based water-proofings or coatings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For clamping of on-site sheetings, fitting to floor drain series HL3100 and HL5100

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL3100 and HL5100

For under-tile waterproo-fings, fitting to floor drain series HL3100 and HL5100

For bitumen based water-proofings or coatings, fitting to floor drain series HL3100 and HL5100

For clamping of on-site sheetings, fitting to floor drain series HL317 and HL72.1

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL317 and HL72.1

For under-tile waterproo-fings, fitting to floor drain series HL317 and HL72.1

HL3020 HL37N HL3000 HL37NP HL38N HL39G HL3910 HL3911 HL66(Q) HL3928 HL3120 HL3121 HL3123 HL3124 HL3125 HL3127

HL83.0 HL83 HL83.M HL83.H HL8300.0 HL8300 HL8300.M HL8300.H HL84.0 HL84 HL84.M

171


Product HL3020 HL37N HL3000 HL37NP HL38N HL39G HL3910 HL3911 HL66(Q) HL3928 HL3120 HL3121 HL3123 HL3124 HL3125 HL3127

Description Tilable extension Standard extension


Extension with PVC-collar

Round extension Cast iron exten-sion


Extension „Klick-Klack“ with screwable grate

Extension Extension with design-grate „Hamam“

Design-grate „Quadra“

Design-grate „Seine“

Design-grate „Orinoco“

Design-grate „Nil“ Design-grate „Yukon“

Design-grate „Primus Design“

Function Extension fits to drain bodies HL70K-3020, HL80K-3020, HL90K-3020, HL300K-3020, HL304K-3020, HL310NK-3020 and HL510NK-3020

Standard exten-sion, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Standard extension with stainless steel frame, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

To connect PVC floor coverings, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Extension with round cover plate, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304

Usage with high load or to con-nect hot bitumen floor coverings, fitting to floor drain series HL90, HL510N, HL80, HL300, HL70, HL310N, HL304



Stainless steel grate with high request on design and stability, fitting to floor drain series HL72.1 and HL317

Extension for floor drain with golden frame and grate, design „Hamam“. Fits to floor drain series HL5100 and HL3100.







Product HL83.0 HL83 HL83.M HL83.H HL8300.0 HL8300 HL8300.M HL8300.H HL84.0 HL84 HL84.M

Description Sealing kit without sheeting Sealing kit with EPDM sheeting


Sealing kit with bitumen collar Sealing kit without sheeting Sealing kit with EPDM sheeting


Sealing kit with bitumen collar

Sealing kit without sheeting Sealing kit with EPDM sheeting


Function For clamping of on-site sheetings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For under-tile waterproofings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For bitumen based water-proofings or coatings, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N

For clamping of on-site sheetings, fitting to floor drain series HL3100 and HL5100

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL3100 and HL5100

For under-tile waterproo-fings, fitting to floor drain series HL3100 and HL5100

For bitumen based water-proofings or coatings, fitting to floor drain series HL3100 and HL5100

For clamping of on-site sheetings, fitting to floor drain series HL317 and HL72.1

For bitumen coatings and EPDM sheetings, fitting to floor drain series HL317 and HL72.1

For under-tile waterproo-fings, fitting to floor drain series HL317 and HL72.1

HL3020 HL37N HL3000 HL37NP HL38N HL39G HL3910 HL3911 HL66(Q) HL3928 HL3120 HL3121 HL3123 HL3124 HL3125 HL3127

HL83.0 HL83 HL83.M HL83.H HL8300.0 HL8300 HL8300.M HL8300.H HL84.0 HL84 HL84.M

172

HL080.5E

HL037N.0E

HL037Pr.1E

HL037N.0E

HL037Pr.1E

HL080.5E

HL037N.2E

HL01067D

HL0300.0EN

HL80K

12-

70

Ø220

123 x123

DN

75

DN

50180

90

215

HL3200

HL0510NC.1E

HL0510NCN.2E

HL80CK

HL80.1 Floor drain with convertable outlet

HL-No. Dimension Weight EAN Piece/package80.1 DN50/75 625 g +700813 1

Data

Capacity 0,5 l/sMaterial PP,PE, stainless steel V2AOutlet DN50/75 cuttable, stepless

convertable from horizontal to vertical, outlet pluggable and weldable

Extension 123 x 123 mm, cuttable in heightGrate Stainless steel grate 115 x 115 mmStench trap Height of water trap 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Floor drainage inside the buildingAdditional information

temperature-resistant up to 85 °C

Including Supporting frame, lot cover

HL Floor drains – Products – Data

HL80.1C Floor drain with polymere concrete collar

HL-No. Dimension Weight EAN Piece/package80.1C DN50/75 6100 g +050802 1

Data

Capacity 0,5 l/sMaterial PP,PE, polymere concrete collar,

stainless steel V2AOutlet DN50/75 adjustable in length,

convertable from horizontal to vertical, connector pluggable and weldable

Extension 123 x 123 mm, adjustable in lengthGrate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Under-tile waterproofings and

epoxy resin coatingsAdditional information



HL80.1

HL80.1C

173

HL037N.0E

HL037Pr.1E

HL080.5E

HL037N.2E

HL0300.0EN

Ø 420123 x 123

DN50

DN75

12-7

093

218

180

HL038.3E

HL038N.4E

HL080.5E

HL0300.0EN

HL80K

HL01067D

HL38N

HL80.1H Floor drain with bitumen collar

HL-No. Dimension Weight EAN Piece/package80.1H DN50/75 1195 g +701810 1

Data

Capacity 0,5 l/sMaterial PP,PE, premounted bitumene

membrane, stainless steel V2AOutlet DN50/75 adjustable in length,


Extension 123 x 123 mm, cuttable in height Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Bitumen waterproofingsAdditional information



HL80.1R Floor drain with round cover plate

HL-No. Dimension Weight EAN Piece/package80.1R DN50/75 650 g +004591 1

Data

Capacity 0,5 l/sMaterial PP,PE, stainless steel V2AOutlet DN50/75 adjustable in length,


Extension Stainless steel frame Ø 133 mm, cuttable in height

Grate Stainless steel cover plate Ø 112 mm

Stench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Barrier-free showers with round

cover plateAdditional information



HL80.1H

HL80.1R

174

HL515

HL080.7E

HL01067D

HL080.6E

HL0300.0EN

100 x100

Ø220

12-

75

DN

75

DN

50

100

180

90

215

Ø100

DN40

DN50

95

35

165

132-

153

HL080.2ENWE

HL80K

HL0300.6E

HL0300.0EN123 x123

Ø200

123

12-

70

52

110 165

DN50 DN

40

DN50

HL037N.0E

HL037Pr.1E

HL037N.2E

HL01067D

HL300K

HL80.2 Floor drain with standpipe

HL-No. Dimension Weight EAN Piece/package80.2 DN50/75 535 g +700820 1

Data

Capacity 0,5 l/sMaterial PP, PEOutlet DN50/75 adjustable in length,


Extension 100 x 100 mm, cuttable in heightGrate 94 x 94 mm cover Stench trap Height of seal water 30 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Brick-built bathtubs, longer

standpipe on request! Additional information


Including Lot cover, standpipe HL515 with 10 cm

HL300 Floor drain with side inlet and backwater protector

HL-No. Dimension Weight EAN Piece/package300 DN50 935 g +703005 1

Data

Capacity 0,5 l/sMaterial PE, stainless steel V2AOutlet horizontal DN50,

side inlet DN40/50, Connections pluggable and weldable

Extension 123 x 123 mm, cuttable in height

Grate Stainless steel grate 115 x 115 mm Stench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Central siphoning with side inlet,

which cares for water in the trapAdditional information

with backwater protector, temperature-resistant up to 85 °C


HL303K Floor drain body with 3 side inlets

HL-No. Dimension Weight EAN Piece/package303K DN50 230 g +703036 1

Data

Capacity 0,5 l/sMaterial PEOutlet horizontal DN50,

3 side inlets, connections pluggable and weldable

Grate with Accessories: Plug HL306 or with Trap seal assembly HL307

Stench trap Height of seal water 35 mmRecommended for Central drainage and siphoning for

the whole bathroomAdditional information

no connection to the waterproofing

Including Lot cover

HL80.2

HL300

HL303K

175

HL037N.0E

HL037Pr.1E

HL037N.2E

HL01067D

HL0510.7E

HL3200

HL0510.7EKK

HL310NHL310N-3000

HL0300.0EN

HL310NK

HL037N.0E

HL037Pr.1E

HL0300.6E

HL037N.2E

HL01067D

HL0300.0EN

12-

7052

Ø200123 x123

DN4095110

DN50

71

HL304K

HL304 Floor drain with 3 side inlets

HL-No. Dimension Weight EAN Piece/package304 DN50 795 g +703043 1

Data

Capacity 0,5 l/sMaterial PE, stainless steel V2AOutlet horizontal DN50,

3 side inlets DN40, connections pluggable and weldable

Extension 123 x 123 mm, cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Central drainage and siphoning of

the whole bathroom, the inlets care for enough water in the trap

Additional information

with backwater protector, temperature-resistant up to 85 °C


HL310N Floor drain HL310N-3000 Floor drain like HL310N, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package310N DN50/75/110 690 g +004638 1310N-3000 DN50/75/110 735 g +016327 1

Data

Capacity 0,67 l/sMaterial PE, stainless steel V2AOutlet DN50/75/110,

vertical pluggable and weldable Extension HL310N: 123 x 123 mm,

cuttable in height HL310N-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kgRecommended for Floor drainage with vertical

connectionAdditional information



HL304

HL310N HL310N-3000

176

HL037G.1E

HL038N.4E

HL01067D

HL0510.7E

HL037G.2E

HL038N.3E

HL310NG HL310NR

HL0300.0EN

32-7

3

150 x 150

144

DN110

DN75DN50

Ø 200

6255

HL310NK

HL03020.1E

HL2000KK

HL01067D

HL03020.2E

HL0510.7EKK

HL310N-3020

HL310NPr-3020

AA

10-

80

132 x132

Ø200

144

5562

DN50DN75DN110

104 x104

12

22

HL310NK-3020

HL03020.0E

HL310NG Floor drain with cast iron frame and grate HL310NR Floor drain like HL310NG, but with round cover plate

HL-No. Dimension Weight EAN Piece/package310NG DN50/75/110 2365 g +004652 1310NR DN50/75/110 630 g +006038 1

Data

Capacity 0,67 l/sMaterial PE, cast iron/PP,

stainless steel V2AOutlet DN50/75/110,

vertical, pluggable and weldable Extension HL310NG: 150 x 150 mm,

cuttable in height HL310NR: Ø 133 mm, cuttable in height

Grate HL310NG: 137 x 137 mm, Cast iron HL310NR: Ø 112 mm, Stainless steel

Stench trap Height of seal water 50 mmStandard EN 1253Load classification HL310NG: L15 – max. 1,5 t

HL310NR: K 3 – max. 300 kgRecommended for HL310NG: e.g. carparks, mastic

asphalt HL310NR: barrier-free showers



Including Lot cover

HL310N-3020 Floor drain with tilable extension HL310NPr-3020 like HL310N-3020, but with Primus trap

HL-No. Dimension Weight EAN Piece/package310N-3020 DN50/75/110 740 g +034383 1310NPr-3020 DN50/75/110 765 g +034390 1

Data

Capacity HL310N-3020: 0,67 l/s HL310NPr-3020: 0,5 l/s

Material PP,PE,ABS, stainless steel V4AOutlet DN50/75/110, pluggable and

weldableExtension 132 x 132 mm with stainless steel

frame V4A, cuttable in heightGrate Stainless steel frame and special

grate, to be filled with tilesSize of grate: 104 x 104 x 12 mm

Stench trap HL310N-3020: Height of seal water 50mmHL310NPr-3020: Primus trap with 50mm seal water

Standard EN 1253, ÖNORM B2501Load classification K 3 - max. 300 kgRecommended for e.g. tiled showers, SPA-areaAdditional information

Temperature-resistant up to 85°C

Including Lot cover

HL310NG HL310NR

HL310N-3020 HL310NPr-3020

177

HL037Pr.1E

HL3200

HL01067D

HL2000KKHL2000

HL037N.2E

HL037N.0E

HL310NPrHL310NPr-3000

HL0300.0EN

HL310NK

HL310NPr=123x123HL310NPr-3000=121x121

Ø200

DN50

DN75

DN110

144

HL31

0NPr

=12-

70HL

310N

Pr-3

000=

10-8

0

5562

HL037G.1E

HL038N.4E

HL2000

HL037G.2E

HL038N.3E

HL310NPrGHL310NPrR

HL01067D

HL0300.0EN

Ø 200

DN50DN75

DN110

144

150 x 150

32-7

3

5562

HL310NK

HL310NPr Floor drain with Primus trap HL310NPr-3000 like HL310NPr, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package310NPr DN50/75/110 700 g +004676 1310NPr-3000 DN50/75/110 760 g +016440 1

Data

Capacity 0,5 l/sMaterial PEOutlet DN50/75/110,

vertical, pluggable and weldable Extension HL310NPr: 123 x 123 mm,

cuttable in height HL310NPr-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mm and

Primus (No stench, with or without water)

Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for Floor drainage with vertical

connectionAdditional information

Floor drainage especially at unfrequent use, no stench with or without water, refilling of water into the trap is no longer neccessary! Temperature resistant up to 85 °C


HL310NPrG Floor drain like HL310NG, but with Primus trap HL310NPrR Floor drain like HL310NR, but with Primus trap

HL-No. Dimension Weight EAN Piece/package310NPrG DN50/75/110 2365 g +004690 1310NPrR DN50/75/110 590 g +006052 1

Data

Capacity 0,5 l/sMaterial PE, cast iron/PP, stainless steel V2AOutlet DN50/75/110,

vertical, pluggable and weldable Extension HL310NPrG: 150 x 150 mm,

cuttable in height HL310NPrR: Ø 133 mm, cuttable in height

Grate HL310NPrG: 137 x 137 mm, Cast iron HL310NPrR: Ø 112 mm,Stainless steel

Stench trap Height of seal water 50 mm u. Primus (No stench, with or without water)

Standard EN 1253, ÖNORM B2501Load classification HL310NG: L15 – max. 1,5 t

HL310NR: K 3 – max. 300 kgRecommended for HL310NPrG: e.g. carparks, mastic

asphalt HL310NPrR: barrier-free showers


Floor drainage especially at unfrequent use, no stench with or without water, refilling of water into the trap is no longer neccessary! Temperature resistant up to 85° C

Including Lot cover

HL310NPr HL310NPr-3000

HL310NPrG HL310NPrR

178

HL03910.1E

HL01093D

HL05100.7E

HL03910.2E

HL03900.0E

HL03100.0E

HL3100K

HL03100.0E

DN50

DN75DN110

162

75

Ø239

8-80

Ø152

145x 145

87

HL3100K

HL2100

HL03910.1E

HL01093D

HL03910.2E

HL03900.0E

HL3100 Floor drain with high capacity

Data

Capacity DN50: 1,25 l/s, DN75/110: 1,4 l/sMaterial PE, stainless steelOutlet DN50/75/110,

vertical, pluggable and weldable Extension Stainless steel V4A, 145 x 145

mm, „Klick-Klack“-locking system, cuttable in height

Grate Stainless steel V2A, 138 x 138 mm Stench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for Floor drain with high capacity, e.g.

„Raindance“Additional information

with „Klick-Klack-fixing system“, temperature-resistant up to 85 °C


HL-No. Dimension Weight EAN Piece/package3100 DN50/75/110 1040 g +025428 1

HL3100Pr Floor drain with high capacity and Primus trap

HL-No. Dimension Weight EAN Piece/package3100Pr DN50/75/110 1079 g +025435 1

Data

Capacity 0,8 l/sMaterial PE, stainless steelOutlet DN50/75/110,

vertical, pluggable and weldable Extension Stainless steel V4A, 145 x 145


Grate Stainless steel V2A, 138 x 138 mm Stench trap Height of seal water 50 mm and


Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for Floor drain with high capacity, e.g.

„Raindance“Additional information

Floor drainage especially at unfrequent use, no stench with or without water, refilling of water into the trap is no longer neccessary! Temperature resistant up to 85 °C


HL3100

HL3100Pr

179

150 x150Ø300

DN50DN75

DN110Ø160

50110

20-

70

DN110

50

Ø160

DN75

DN50

Ø300150 x150

Ø500

15-

65

117

HL0317.1E

HL0317.5E

HL0317.2E

HL01059D

HL0317.3E

HL0317.4E

HL0317K

HL0317.1E

HL0317.5E

HL0317.2E

HL062B.3E

HL0317.3E

HL0317HK

HL317K

HL317KH

HL0317.4E

HL317 Floor drain vertical

HL-No. Dimension Weight EAN Piece/package317 DN50/75/110 1200 g +703173 1

Data

Capacity 1,8 l/sMaterial PP, stainless steel V2AOutlet DN50/75/110, vertical Extension 147 x 147 mm, cuttable in height Grate Stainless steel grate 138 x 138 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for Floor drain with high capacityAdditional information


Including Lot cover

HL317H Floor drain vertical with bitumen collar

HL-No. Dimension Weight EAN Piece/package317H DN50/75/110 1985 g +317110 1

Data

Capacity 1,8 l/sMaterial PP, stainless steel V2AOutlet DN50/75/110 vertical Extension 147 x 147 mm, cuttable in height Grate Stainless steel grate 138 x 138 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for Floor drain with high capacity Additional information

Bitumen waterproofings, temperature-resistant up to 95 °C

Including Lot cover

HL317

HL317H

180

HL037N.0E

HL037Pr.1E

HL037N.2E

HL01067D

HL0510.7E

HL3200

HL0510.7EKK

HL510NHL510N-3000

HL0300.0EN

HL510NK

HL2000KK

HL01067D

HL03020.2E

HL0510.7EKK

HL03020.1E

HL510N-3020

HL510NPr-3020

HL03020.0E

HL510NK-3020

12

132 x132

Ø200

DN40

DN50

10-

80

79

188

104 x104

22

AA

HL510N Floor drain HL510N-3000 Floor drain like HL510N, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package510N DN40/50 590 g +051007 1510N-3000 DN40/50 725 g +016686 1

Data

Capacity 0,55l/s with 20mm stowage height0,40l/s with 10mm stowage height

Material PE, stainless steel V2AOutlet DN40/50,

horizontal, pluggable and weldable Extension HL510N: 123 x 123 mm,

cuttable in height HL510N-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for Floor drainage with horizontal

connection Additional information

Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories).


HL-No. Dimension Weight EAN Piece/package510N-3020 DN40/50 730 g +034406 1510NPr-3020 DN40/50 750 g +034413 1

Data

Capacity HL510N-3020:0,50l/s with 20mm stowage height 0,45l/s with 10mm stowage height HL510NPr-3020:0,45l/s with 20mm stowage height 0,40l/s with 10mm stowage height

Material PP,PE,ABS, stainless steel V4A

Outlet DN40/50 horizontal, pluggable and weldable

Extension 132 x 132 mm with stainless steel frame V4A, cuttable in height

Grate Stainless steel frame and special grate, to be filled with tilesSize of grate: 104 x 104 x 12 mm

Stench trap HL510N-3020: Height of seal water 50mmHL510NPr-3020: PRIMUS trap with 50mm seal water

Standard EN 1253, ÖNORM B2501

Load classification K 3 - max. 300 kg

Recommended for e.g. tiled showers, SPA-area


Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories)

Including Lot cover

HL510N-3020 Floor drain with frame for tiles HL510NPr-3020 Like HL510N-3020, but with PRIMUS trap

HL510N HL510N-3000

HL510N-3020 HL510NPr-3020

181

HL037G.1E

HL038N.4E

HL01067D

HL0510.7E

HL037G.2E

HL038N.3E

HL510NG HL510NR

HL0300.0EN

HL510NK

HL037Pr.1E

HL3200

HL01067D

HL2000KKHL2000

HL037N.2E

HL037N.0E

HL510NPrHL510NPr-3000

HL0300.0EN

HL510NK

HL510NG Floor drain with cast iron frame and grate HL510NR like HL510NG, but with round stainless steel cover plate

HL-No. Dimension Weight EAN Piece/package510NG DN40/50 2265 g +001965 1510NR DN40/50 590 g +006076 1

Data

Capacity 0,55 l/sMaterial PE, cast iron/PP, stainless steel

V2AOutlet DN40/50,

horizontal, pluggable and weldable Extension HL510NG: 150 x 150 mm,

cuttable in height HL510NR: Ø 133 mm,cuttable in height

Grate HL510NG: 137 x 137 mm, Cast ironrost HL510NR: Ø 112 mm Edelstahl

Stench trap Height of seal water 50 mmStandard EN 1253Load classification HL510NG: L15 – max. 1,5 t

HL510NR: K 3 – max. 300 kg Recommended for HL510NG: e.g. carparks, mastic

asphalt HL510NR: barrier-free showers



Including Lot cover

HL510NPr Floor drain with Primus trap HL510NPr-3000 like HL510NPr, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package510NPr DN40/50 690 g +004737 1510NPr-3000 DN40/50 744 g +016563 1

Data

Capacity 0,50l/s with 20mm stowage height0,35l/s with 10mm stowage height

Material PE, stainless steel V2AOutlet DN40/50,

horizontal, pluggable and weldable Extension HL510NPr: 123 x 123 mm,

cuttable in height HL510NPr-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap Height of seal water 50 mm and


Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for Floor drainage with horizontal

connection Additional information

Floor drainage especially at unfrequent use, no stench with or without water, refilling of water into the trap is no longer neccessary! Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories).


HL510NG HL510NR

HL510NPr HL510NPr-3000

182

HL2090KK

HL037N.2E HL3200

HL2090

HL037G.1E

HL038N.4E

HL2000

HL037G.2E

HL038N.3E

HL510NPrGHL510NPrR

HL01067D

HL0300.0EN

HL037Pr.1E

HL037N.0E

HL01067D

HL0300.0EN

HL510NK

HL90K

HL90Pr HL90Pr-3000

HL510NPrG Floor drain like HL510NPr, but with cast iron frame and grate HL510NPrR like HL510NPrG, but with round stainless steel cover plate

HL-No. Dimension Weight EAN Piece/package510NPrG DN40/50 2440 g +004713 1510NPrR DN40/50 690 g +006113 1

Data

Capacity 0,5 l/sMaterial PE, cast iron/PP, stainless steel V2AOutlet DN40/50,

horizontal, pluggable and weldable Extension HL510NPrG: 150 x 150 mm,

cuttable in height HL510NPrR: Ø 133 mm, cuttable in height

Grate HL510NPrG: 137 x 137 mm, cuttable in height HL510NPrR: Ø 112 mm, cuttable in height

Stench trap Height of seal water 50 mm and Primus (No stench, with or without water)

Standard EN 1253, ÖNORM B2501Load classification HL510NPrG: L15 – max. 1,5 t

HL510NPrR: K 3 – max. 300 kg Recommended for HL510NPrG: e.g. carparks, mastic

asphalt HL510NPrR: barrier-free showers



Including Lot cover

HL90Pr Floor drain flat with Primus trap HL90Pr-3000 like HL90Pr, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package90Pr DN40/50 510 g +028214 190Pr-3000 DN40/50 564 g +028535 1

Data

Capacity 0,43 l/sMaterial PE, stainless steel V2AOutlet DN40/50,

horizontal, pluggable and weldable Extension HL90Pr: 123 x 123 mm,

cuttable in height HL90Pr-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mm Stench trap Height of seal water 30 mm and


Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for Floor constructions < 100 mm Additional information



HL510NPrG HL510NPrR

HL90Pr HL90Pr-3000

183

HL03020.2E

HL03020.1E

HL01067D

HL03020.0E

104 x104132 x132

Ø200

10-

80

DN50

DN40

188

57

22

AA

HL90PrDHL90PrD-3000

HL90KD

HL037N.2E HL3200

HL2090

HL037Pr.1E

HL037N.0E

HL090PrD.4E

HL2090KK

HL2090KK

HL90K-3020

HL90Pr-3020 Floor drain with tilable extension and PRIMUS trap

HL-No. Dimension Weight EAN Piece/packageHL90Pr-3020 DN40/50 570 g +034321 1

Data

Capacity 0,43l/s with 20mm stowage height 0,40l/s with 10mm stowage height

Material PP,PE,ABS, stainless steel V4AOutlet DN40/50Extension 132 x 132 mm with stainless steel


grate, to be filled with tilesSize of grate: 104 x 104 x 12 mm

Stench trap PRIMUS trap with 30mm seal water

Standard EN 1253, ÖNORM B2501Load classification K 3 - max. 300 kgRecommended for e.g. tiled showers, SPA-area, with

floor levels < 100mmAdditional information

Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories)

Including Lot cover

HL90PrD Floor drain with integrated fleece flangeHL90PrD-3000 like HL90PrD, but with stainless steel frame

HL-No. Dimension Weight EAN Piece/package90PrD DN40 812 g +029471 190PrD-3000 DN40 855 g +029518 1

Data

Capacity 0,40 l/sMaterial PE, cast iron/PE, stainless steel

V2AOutlet DN40,

horizontal, pluggable and weldable Extension HL90PrD: 123 x 123 mm,

cuttable in height HL90PrD-3000: 121 x 121 mm, „Klick-Klack-fixing system“, cuttable in height

Grate Stainless steel grate 115 x 115 mm Stench trap Height of seal water 30 mm and

PRIMUS (No stench, with or without water)

Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for Floor constructions < 100 mm Additional information



HL90Pr-3020

HL90PrD HL90PrD-3000

184

HL03910.1E

HL03900.0E

HL0540.2E

HL2040

HL0540.4E

HL0540.0E

HL0540.3E

HL540K

HL0540I

HL540 HL540I

HL0540.5E

HL2040I

HL066C.1EHL066Q.1E HL0540I

Quadra Cut Individuell

HL3128EHL3928

Data

Capacity 20 mm above drain level: HL540=0,8l/s; HL540i=0,6/s10 mm above drain level: HL540=0,55l/s; HL540i=0,45l/s

Material PP/stainless steel, Frame: V4AGrate HL540=V2AGrate HL540i=V4A

Outlet DN50 horizontalHeight from 8 - 20 cm adjustableStandard EN 1253Load classification K3 - max. 300kg

Stench trap 5cm seal water, incl. Primus-trap, no stench without seal water


incl. removable trap inlet, sealing kit with textile coated membrane, sound disconnected adjusting angles, protection cover and lot cover

Installation The drain body might be fixed on the floor with 3 metal angles and can be adjusted in height afterwards. Advantage: maximum screed covering of the outlet pipe. New: It is no longer necessary to set the drain exactly on the right height of the screed. After filling in the screed, the salient nozzle is cut by a saw. The sealing kit may be inserted without any tools and takes care of a safe connection to the waterproofing. At the end the extension is adjusted and set into the drain.

HL066Q.1E, HL066C.1E, HL0540I, HL3928, HL3128E Design grates

Data

Material Stainless steel V4AGrate HL540I: 138x138mm massive,

Tile hollow: 74x74 mm, depth 13mm

Load classification L - max. 1,5t, HL0540I - K3Recommended for Shower drain HL540 or floor drain

series HL5100, HL3100, HL72.1 and HL317

HL540 „Primus Drain“ Duschablauf, MIN. HEIGHT 80 MM !HL540I Shower drain „Primus Drain“ with individual tile hollow, MIN. HEIGHT 80 MM !

HL-No. Material Dimension Weight EAN Piece/package540 PP/Stainless steel DN50 1533 g +039029 1540I PP/Stainless steel DN50 1898 g +039098 1540-Quadra PP/Stainless steel DN50 1898 g +041817 1540-Cut PP/Stainless steel DN50 1898 g +041800 1540-Hamam PP/Stainless steel/PVD-coated DN50 1898 g +041824 1

HL-No. Material Dimension Weight EAN Piece/package066Q.1E Stainless steel V4A 138 x 138 x 5 mm 607 g +013623 1 066C.1E Stainless steel V4A 138 x 138 x 5 mm 608 g +031283 10540I Stainless steel V4A 138 x 138 x 5 mm 638 g +039104 13928 Stainless steel V4A/PVD-coated 138 x 138 x 5 mm 608 g +031283 13128E Stainless steel V4A 138 x 138 x 5 mm 1

Hamam (Stainless steel/PVD-coated) Hamam (Stainless steel)

Please also see installation movie

at www.hl.at

HL540HL540I

HL066Q.1E, HL066C.1E, HL0540I, HL3928, HL3128E

185

HL3120 HL3121 HL3122

HL3124 HL3125

HL3127

115 x 115 5

HL3123

HL0541I

HL037Pr.1E

HL2020

HL0541.0E

HL0541.3E

HL541K

HL0540I

HL541 HL541I

HL0541.5E

HL0541.4E

HL037N.0E

HL0541.2E

Data

Capacity 20 mm above drain level: HL541=0,5l/s; HL541i=0,45/s10 mm above drain level: HL541=0,4l/s; HL541i=0,4l/s

Material PP/stainless steel, Frame: V4AGrate HL541=V2AGrate HL541i=V4A

Outlet DN40/DN50 horizontalHeight from 62 - 200 (230) mmStandard EN 1253Load classification K3 - max. 300 kgStench trap „Primus blue“ trap, no

stench without seal waterAdditional information

Incl. removable trap inlet, sealing kit with textile coated membrane, adjustable fixing angles, lot cover and protection cover

Installation The drain body might be fixed on the floor with 3 metal angles and can be adjusted in height afterwards. Advantage: maximum sceed covering of the outlet pipe. New: It is no longer necessary to set the drain exactly on the right height of the screed. After filling in the screed, the salient nozzle is cut by a saw. The sealing kit may be inserted without any tools and takes care of a safe connection to the waterproofing. At the end the extension is adjusted and set into the drain. Please take care, that the edges of the frame are underlaid with tile glue to take maximum load.

HL541 Flat shower drain Primus blue, MIN. HEIGHT 62MM!HL541I Flat shower drain Primus blue with individual tile hollow, MIN. HEIGHT 62MM!

HL-No. Material Dimension Weight EAN Piece/packageHL541 PP/Stainless steel DN40/50 1121 g +047642 1HL541I PP/Stainless steel DN40/50 1388 g +047659 1HL541-Quadra PP/Stainless steel DN40/50 1819 g - 1

HL0541I, HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127 Design grates

HL-No. Dimension Weight EAN Piece/package3120 115 x 115 mm 425 g +015412 13121 115 x 115 mm 425 g +015429 13122 115 x 115 mm 425 g +015443 13123 115 x 115 mm 425 g +015443 13124 115 x 115 mm 425 g +015450 13125 115 x 115 mm 425 g +015467 13127 115 x 115 mm 430 g +029037 10541I 115 x 115 mm 800 g +048304 1

Daten

Material Stainless steel V4AGrate Stainless steel grate 115 x 115 mmLoad classification L – max. 1,5 tRecommended for Floor drain series HL70, HL80,

HL300, HL304, HL310N, HL510N, HL90 combined with extensions HL3200 or HL3210HL0541I: HL541

Please also see installation movie and

movie „function of Primus blue“

at www.hl.at

HL541HL541I

HL0541I, HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127

186

HL03910.1E

HL01093D

HL2100

HL03910.2E

HL03900.0E

HL03100.0E

HL5100K

HL03910.1E

HL01093D

HL05100.7E

HL03910.2E

HL03900.0E

HL03100.0E

HL5100K

HL5100 Floor drain with high capacity

HL-No. Dimension Weight EAN Piece/package5100 DN50/75 1025 g +025442 1

Data

Capacity 1,0 l/sMaterial PE, stainless steelOutlet DN50/75,

horizontal, pluggable and weldableExtension Stainless steel V4A, 145 x 145


Grate Stainless steel V2A, 138 x 138 mm Stench trap Height of seal water 50 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for e.g. barrier-free showers with high

volume (Raindance) Additional information

with stainless steel frame, Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories).


HL5100Pr Floor drain with high capacity, with PRIMUS trap

HL-No. Dimension Weight EAN Piece/package5100Pr DN50/75 1069 g +025459 1

Data

Capacity 0,8 l/sMaterial PE, stainless steelOutlet DN50/75,

horizontal, pluggable and weldableExtension Stainless steel V4A, 145 x 145


Grate Stainless steel V2A, 138 x 138 mm Stench trap Height of seal water 50 mm and

PRIMUS (No stench, with or without water)

Standard EN 1253, ÖNORM B2501Load classification K 3 – max. 300 kg Recommended for e.g. barrier-free showers

with high volume (Raindance) Additional information

with stainless steel frame, Floor drainage especially at unfrequent use, no stench with or without water, refilling of water into the trap is no longer neccessary! Sound protection acc. ÖNORM B8115-2 is reached together with HL6200 sound insulation pad (see chapter accessories).


HL5100

HL5100Pr

187

HL072.1E

HL0317.5E

HL0317.2E

HL01059D

HL0317.4E

HL0317.1E

HL72.1N HL72.1

HL72.1HN HL72.1H

HL072.1E

HL0317.5E

HL0317.2E

HL062B.3E

HL0317.4E

HL0317.1E

150 x150Ø300

20-

70D

N75

DN

110

60

80

150

60

80

150

DN

75

Ø500

Ø300

150x 150

DN

110

20-

70

HL072.3E

HL072.3E

HL72.1KH

HL72.1K

HL72.1N Floor drain HL72.1 like HL72.1, but with plastic grate

HL-No. Dimension Weight EAN Piece/package72.1N DN75/100 1330 g +107216 172.1 DN75/100 1330 g +710720 1

Data

Capacity 1,5 l/sMaterial PP, stainless steel V2A

Outlet DN75/110Extension 147 x 147 mm,

cuttable in height Grate HL72.1: Plastic grate

138 x 138 mm, HL72.1N: Stainless steel grate 138 x 138 mm

Stench trap Height of seal water 60 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for e.g. barrier-free showers with with

high volume (Raindance) Additional information


Including Lot cover and Sand trap

HL72.1HN Floor drain with bitumen collar HL72.1H Floor drain with bitumen collar and plastic grate

HL-No. Dimension Weight EAN Piece/package72.1HN DN75/100 2200 g +072118 172.1H DN75/100 2086 g +997213 1

Data

Capacity 1,5 l/sMaterial PP, stainless steel V2A

Outlet DN75/110Extension 147 x 147 mm,

cuttable in height Grate HL72.1H: Plastic grate

138 x 138 mm, HL72.1HN: Stainless steel grate 138 x 138 mm

Stench trap Height of seal water 60 mmStandard EN 1253Load classification K 3 – max. 300 kg Recommended for e.g. barrier-free showers with high

volume (Raindance) Additional information


Including Lot cover and Sand trap

HL72.1N HL72.1

HL72.1HN HL72.1H

188

HL037Pr.1E

HL01067D

HL037N.0E123 x 123

Ø 110

1090

HL037N.2E

HL01067D

HL037N.0E

HL037Pr.1E

HL2000

HL37N.1HL37NPr

HL37FPr

HL0510.7E HL2090123 x 123

Ø 110

1090

HL037Pr.1E

HL037N.2E

HL037Pr.1E

HL01067D

HL037N.0E

Ø110

121 x121

100

22 6

HL3200

HL Floor drains – Accessories – Data

HL37N Standard extension

HL-No. Dimension Weight EAN Piece/package37N Ø 110 mm / 123 x 123 mm 350 g +015221 1

Data

Material PP, stainless steel V2AExtension PP-Frame 123 x 123 mm,

extension cuttable in height Grate Stainless steel grate 115 x 115 mmLoad classification K 3 – max. 300 kg Recommended for Drain bodies of series HL70, HL80,

HL300, HL304, HL310N, HL510N, HL90

Including Supporting frame

HL37N.1 Extension with water trap HL37NPr Extension with PRIMUS trap HL37FPr Extension with flat PRIMUS trap

HL-No. Dimension Weight EAN Piece/package37N.1 Ø 110 mm / 123 x 123 mm 380 g +015245 137NPr Ø 110 mm / 123 x 123 mm 405 g +015269 137FPr Ø 110 mm / 123 x 123 mm 380 g +028450 1

Data

Material PP, stainless steel V2AExtension PP-Frame 123 x 123 mm,

extension cuttable in height Grate Stainless steel grate 115 x 115 mmStench trap HL37N.1: Water trap

HL37NPr: PRIMUS trapHL37FPr: PRIMUS trap „flat“

Load classification K 3 – max. 300 kg Recommended for Drain bodies of series HL310N

and HL510N Including Supporting frame

HL3000 Extension system „Klick-Klack“ with stainless steel frameHL3011 Extension system „Klick-Klack“ with stainless steel frame, screwed

HL-No. Dimension Weight EAN Piece/package3000 Ø 110 mm / 121 x 121 mm 340 g +015313 13011 Ø 110 mm / 121 x 121 mm 340 g +032624 1

Data

Material PE, stainless steel V2AExtension Stainless steel frame 121 x 121

mm, extension cuttable in height Grate Stainless steel grate 115 x 115 mmLoad classification K 3 – max. 300 kg Recommended for Drain bodies of series HL70, HL80,

HL300, HL304, HL310N, HL510N, HL90


HL37N

HL37N.1 HL37NPr HL37FPr

HL3000HL3011

189

HL037Pr.1E

HL01067D

HL037NP.2E

185 x185

121 x121

Ø110

1,5

110

4,5

HL340N

HL01067D

HL0510.7EKK

HL2000KK

HL2090KK

HL3000.1HL3000Pr

HL3000FPr

Ø 110

121 x 121

22 6

100

HL037Pr.1E

HL037N.0E

HL3200

2712

118

Ø110

104 x104132 x132

AA

HL01067D

HL03020.1E

HL03020.2E

HL3000.1 Extension „Klick-Klack“, including water trap HL3000Pr Extension „Klick-Klack“, including PRIMUS trap HL3000FPr Extension, including PRIMUS trap - flat

HL-No. Dimension Weight EAN Piece/package3000.1 Ø 110 mm / 121 x 121 mm 425 g +015337 13000Pr Ø 110 mm / 121 x 121 mm 450 g +015351 13000FPr Ø 110 mm / 121 x 121 mm 426 g +028542 1

Data

Material PE, stainless steel V2AExtension Stainless steel frame 121 x 121

mm, extension cuttable in height Grate Stainless steel grate 115 x 115 mmStench trap HL3000.1: Water trap

HL3000Pr: PRIMUS trap HL3000FPr: PRIMUS trap „flat“

Load classification K 3 – max. 300 kg Recommended for Drain bodies of series HL310N

and HL510NIncluding Supporting frame

HL37NP Extension with PVC frame and collar

HL-No. Dimension Weight EAN Piece/package37NP Ø 110 mm / 121 x 121 mm 340 g +022762 1

Data

Material PP/PVC/stainless steel V2AExtension PVC frame and collar

185 x 185 mm / 121 x 121 mm, Extension cuttable in height

Grate Stainless steel grate 115 x 115 mmLoad classification K 3 – max. 300 kg Recommended for PVC floor coverings, for gluing

PVC coverings directly on the collar, fits to all floor drains of series HL70, HL80, HL300, HL304, HL310N, HL510N, HL90

HL3020 Tilable extension

HL-No. Dimension Weight EAN Piece/packageHL3020 Ø 110 mm / 132 x 132 mm 350 g +034253 1

Data

Material PPExtension 132 x 132 mm with stainless steel


grate, to be filled with tiles; Size of grate: 104 x 104 x 12 mm

Load classification K 3 - max. 300 kgRecommended for e.g. tiled showers, SPA-areaIncluding Lot cover

Fits for all drain bodies with higher lot cover HL70K-3020, HL80K-3020, HL90K-3020, HL300K-3020, HL304K-3020, HL310NK-3020, HL510NK-3020

HL3000.1 HL3000Pr HL3000FPr

HL37NP

HL3020

190

HL038N.4E

HL038.3E

HL01067D

HL01067D

HL038N.3EHL38N.1 HL38NPr

HL0510.7E HL2000HL038N.4E

HL038P.1E

HL038P.4E

Schnitt A-A

126

min

.50

Ø138

Ø110

50

A A

HL038P.2E

HL038P.3E

HL01067D

HL037NP.2E

HL037Pr.1E

HL0510.7E HL2000

HL37NP.1 HL37NPPr

185 x185

121 x121

Ø110

1,5

110

4,5

HL340N

HL37NP.1 Extension with PVC collar and frame, including water trap HL37NPPr Extension with PVC collar and frame, including PRIMUS trap

HL-No. Dimension Weight EAN Piece/package37NP.1 Ø 110 mm / 121 x 121 mm 342 g +022805 137NPPr Ø 110 mm / 121 x 121 mm 342 g +022830 1

Data

Material PP/PVC/stainless steel V2AExtension PVC frame and collar

185 x 185 mm / 121 x 121 mm, Extension cuttable in height

Grate Stainless steel grate 115 x 115 mmStench trap HL37NP.1: Water trap

HL37NPPr: PRIMUS trap Load classification K 3 – max. 300 kg Recommended for PVC floor coverings, for gluing

PVC coverings directly on the collar, fits to all floor drains of series HL310N and HL510N

HL38N Round extension

HL-No. Dimension Weight EAN Piece/package38N Ø 110 mm / Ø 133 mm 160 g +004362 1

Data

Material PP, stainless steel V2AExtension Stainless steel frame Ø 133 mm,

extension cuttable in height Grate Stainless steel cover plate

Ø 112 mmLoad classification K 3 – max. 300 kg Recommended for tiled showers, fitting to floor drain

series HL70, HL80, HL90, HL300, HL304

HL38N.1 Round extension with water trap HL38NPr Round extension with PRIMUS trap

HL-No. Dimension Weight EAN Piece/package38N.1 Ø 110 mm / Ø 133 mm 435 g +015498 138NPr Ø 110 mm / Ø 133 mm 465 g +005994 1

Data

Material PP, stainless steel V2AExtension Stainless steel frame Ø 133 mm,

extension cuttable in height Grate Stainless steel cover plate

Ø 112 mmStench trap HL38N.1: Water trap

HL38NPr: PRIMUS trap Load classification K 3 – max. 300 kg Recommended for tiled showers, fitting to floor drain

series HL310N and HL510N

HL38P Extension for connection to PVC- and rubber floor coverings

HL-No. Dimension Weight EAN Piece/package38P Ø 110 mm / Ø 115 mm 650 g +036097 x

Data

Material PP/ABS/stainless steel V2AExtension Plastic frame 138,5mmGrate Stainless steel grate V2A 115mmTrap Water trap with 50mm water heightLoad classification K 3 – max. 300 kg Recommended for clamping of PVC- or rubber floor

coverings from 1-4 mm, fits for drain series HL70, HL80, HL300, HL304 HL310N and HL510N

HL37NP.1 HL37NPPr

HL38N

HL38N.1 HL38NPr

HL38P

191

HL037G.1E

HL01067DØ 110

150 x 150 8

9530

16

HL037G.2E

HL03910.1E

HL01093D

HL03900.0E

Ø146

145x 1452210

0

HL03910.2E

HL01093D

HL03900.0E

HL05100.7E HL2100

HL3910.1 HL3910Pr

50

Ø146

145x 145

2210

0

HL03910.1E

HL03910.2E

HL01093D

HL03900.0E

HL03911.1E

HL03911.3E

Ø146

145x 1452210

0

HL03911.2E

HL39G Extension with cast iron frame and grate

HL-No. Dimension Weight EAN Piece/package39G Ø 110 mm / 150 x 150 mm 2025 g +000647 1

Data

Material PP / cast ironExtension Cast iron 150 x 150 mm, extension

cuttable in height Grate Cast iron 137 x 137 mmLoad classification L15 bzw. A15 – max. 1,5 t Recommended for Mastic asphalt, carparks; Drain

bodies of series HL70, HL80, HL300, HL304, HL310N, HL510N, HL90

HL3910.1 Extension for series 60 Plus, including water trap HL3910Pr Extension for series 60 Plus, including PRIMUS trap

HL-No. Dimension Weight EAN Piece/package3910.1 Ø 146 mm / 145 x 145 mm 592 g +025541 13910Pr Ø 146 mm / 145 x 145 mm 630 g +025558 1

Data

Material PP, stainless steelExtension Stainless steel frame V4A

145 x 145 mm, extension cuttable in height

Grate Stainless steel grate V2A 138 x 138 mm

Stench trap HL3910.1: Water trap HL3910Pr: PRIMUS trap

Load classification K 3 – max. 300 kg Recommended for Drain bodies of series HL3100 and

HL5100Including Supporting frame

HL3911 Extension for series 60 Plus with screwable grate

HL-No. Dimension Weight EAN Piece/package3911 Ø 146 mm / 145 x 145 mm 470 g +028252 1

Data

Material PP, stainless steelExtension Stainless steel frame V4A





HL3910 Extension for HL3100 and 5100 series


Data

Material PP, stainless steel V2AExtension Stainless steel frame V4A





HL39G

HL3910.1 HL3910Pr

HL3911

HL3910

192

HL66 HL66.1 HL66Q

Ø 145

150 x 150

1520

5 HL066.1E HL066.2E HL066Q.1E

HL066.3E HL066Q.3E

100

22138 x138145 x145

Ø146

AA

HL3128

HL03900.0E

HL03928.1E

HL01093D

100

22138 x138145 x145

Ø146

AA

HL03910G.1E

HL01093D

HL03910G.2E

HL66, HL66Q, HL66.1 Extensions with screwable grate

HL-No. Dimension Weight EAN Piece/package66 Ø 145 mm / 150 x 150 mm 915 g +700660 166Q Ø 145 mm / 150 x 150 mm 1070 g +013609 166.1 Ø 145 mm / 150 x 150 mm 1000 g +702664 1

Data

Material PP/ Stainless steelExtension Stainless steel frame 150 x 150

mm, extension cuttable in height Grate HL66 Screwable stainless steel

grate V4A 138 x 138 mm HL66Q Design grate V4A138 x 138 mm „Quadra“ HL66.1 Anti-slip grate V4A 138 x 138 mm, stainless steel, screwable

Load classification L 15 – max. 1,5 t Recommended for Drain bodies of series HL72.1 and

HL317

HL3928 Extension „HAMAM“ for floor drain series HL3100 and HL5100

HL3910G Extension cast iron for floor drain series HL3100 and HL5100


HL-No. Dimension Weight EAN Piece/package3910G Ø 146 mm /190 x 190 mm 11920 g +048793 1

Data

Material PP/stainless steel V2AExtension Brass plated stainless steel frame

145 x 145mmGrate Brass plated stainless steel V2A

138 x 138 mmLoad classification L 15 - max. 1,5 tRecommended for Floor drain series HL3100 and

HL5100

Data

Material PP/Cast ironExtension Cast iron frame 190 x 190mm,

height 45 - 80 mmGrate Cast iron grate 175 x 175mmLoad classification B - 12,5 tRecommended for Car parks, warehouses, garbage

rooms, mastic asphalt; fits for drain bodies of series HL3100(T)and HL5100(T)

HL66, HL66Q, HL66.1

HL3928

HL3910G

193

100

121 x 121

Ø 110

22 6

HL66.3 HL66.4

150 x 150

90

Ø 145

HL0317.1E

HL0317.2E

HL072.1E

HL3210 Extension with stainless steel frame V4A

HL-No. Dimension Weight EAN Piece/package3210 Ø 110 / 121 x 121 mm 145 g +023769 1

Data

Material PP/Stainless steel V4AExtension Stainless steel frame 121 x 121

mm, extension cuttable in heightRecommended for Chlorinated waste water, e.g. in

thermal baths, fitting to floor drain series HL70, HL80, HL90, HL300, HL304, HL310N, HL510N


HL3110, HL03910.3E Stainless steel grate V4A

HL-No. Dimension Weight EAN Piece/package3110 115 x 115 mm 400 g +015634 103910.3E 138 x 138 mm +025916 1

Data

Material Stainless steel V4AGrate HL3110:

Stainless steel grate 115 x 115 mmHL03910.3E:Stainless steel grate 138 x 138 mm

Load classification K 3 – max. 300 kg Recommended for chlorinated sewer, e.g. in

swimming pools

HL66.3 Extension with stainless steel grate HL66.4 Extension with plastic grate

HL-No. Dimension Weight EAN Piece/package66.3 Ø 145 mm / 150 x 150 mm 352 g +014545 166.4 Ø 145 mm / 150 x 150 mm 238 g +014569 1

Data

Material HL66.3: PP/Stainless steel V2A HL66.4: PP

Extension PP-Frame 150 x 150 mm, Extension cuttable in height

Grate HL66.3: Stainless steel grate 138 x 138 mm HL66.4: Plastic grate 138 x 138 mm

Load classification K 3 – max. 300 kg Recommended for Drain bodies of series HL72.1 and

HL317

HL3210

HL3110, HL03910.3E

HL66.3 HL66.4

194

HL3120 HL3121 HL3122

HL3124 HL3125

HL3127

115 x 115 5

HL3123

HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127 Design grates

HL-No. Dimension Weight EAN Piece/package3120 115 x 115 mm 425 g +015412 13121 115 x 115 mm 425 g +015429 13122 115 x 115 mm 425 g +015443 13123 115 x 115 mm 425 g +015443 13124 115 x 115 mm 425 g +015450 13125 115 x 115 mm 425 g +015467 13127 115 x 115 mm 430 g +029037 1

Data

Material Stainless steel V4AGrate Stainless steel grate 115 x 115 mmLoad classification L – max. 1,5 tRecommended for Floor drain series HL70, HL80,

HL300, HL304, HL310N, HL510N, HL90 combined with extensions HL3200 or HL3210

HL3120, HL3121, HL3122, HL3123, HL3124, HL3125, HL3127

dn110 - hutterer & lechner

Documents