dl-960gm-gs3 tricks

11111

DIGILITE

DL-960GM-GS3-FX

User Manual

Version 1.2Published June 2013

Copyright2013 DIGILITE INC. All rights reserved.

22222

Copyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:Copyright Notice:No part of this manual may be reproduced, transcribed, transmitted, or translated inany language, in any form or by any means, except duplication of documentation bythe purchaser for backup purpose, without written consent of DIGILITE Inc.Products and corporate names appearing in this manual may or may not be regis-tered trademarks or copyrights of their respective companies, and are used only foridentification or explanation and to the owners benefit, without intent to infringe.

Disclaimer:Disclaimer:Disclaimer:Disclaimer:Disclaimer:Specifications and information contained in this manual are furnished for informa-tional use only and subject to change without notice, and should not be constructedas a commitment by DIGILITE. DIGILITE assumes no responsibility for any errors oromissions that may appear in this manual.With respect to the contents of this manual, DIGILITE does not provide warranty of anykind, either expressed or implied, including but not limited to the implied warranties orconditions of merchantability or fitness for a particular purpose.In no event shall DIGILITE, its directors, officers, employees, or agents be liable for anyindirect, special, incidental, or consequential damages (including damages for loss ofprofits, loss of business, loss of data, interruption of business and the like), even ifDIGILITE has been advised of the possibility of such damages arising from any defect orerror in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that

may cause undesired operation.

CALIFORNIA, USA ONLYThe Lithium battery adopted on this motherboard contains Perchlorate, a toxicsubstance controlled in Perchlorate Best Management Practices (BMP) regulationspassed by the California Legislature. When you discard the Lithium battery inCalifornia, USA, please follow the related regulations in advance.Perchlorate Material-special handling may apply, seewww.dtsc.ca.gov/hazardouswaste/perchlorate

33333

ContentsContentsContentsContentsContents1 .1 .1 .1 .1 . IntroductionIntroductionIntroductionIntroductionIntroduction ....................................................................................................................................................................................................................................................................................................... 5 5 5 5 5

1.1 Package Contents ..................................................................... 51.2 Specifications ........................................................................... 61.3 Motherboard Layout ................................................................... 111.4 I/O Panel .................................................................................... 12

2 .2 .2 .2 .2 . Instal lat ionInstal lat ionInstal lat ionInstal lat ionInstal lat ion ................................................................................................................................................................................................................................................................................................................. 13 13 13 13 13Pre-installation Precautions ................................................................ 132.1 CPU Installation ......................................................................... 142.2 Installation of CPU Fan and Heatsink ......................................... 142.3 Installation of Memory Modules (DIMM) .................................... 152.4 Expansion Slots (PCI and PCI Express Slots) ........................... 162.5 Multi Monitor Feature ................................................................. 172.6 Jumpers Setup .......................................................................... 192.7 Onboard Headers and Connectors ............................................. 202.8 SATAII Hard Disk Setup Guide ................................................... 242.9 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks

Installation ................................................................................. 252.10 Hot Plug and Hot Swap Functions for SATA / SATAII HDDs ....... 252.11 SATA / SATAII HDD Hot Plug Feature and Operation Guide ....... 262.12 Driver Installation Guide ............................................................. 282.13 Installing Windows XP / XP 64-bit / VistaTM / VistaTM 64-bit / 7 /

7 64-bit With RAID Functions .................................................... 282.13.1 Installing Windows XP / XP 64-bit With RAID

Functions ............................................................... 282.13.2 Installing Windows VistaTM / VistaTM 64-bit / 7 / 7 64-bit

With RAID Functions ..................................................... 292.14 Installing Windows XP / XP 64-bit / VistaTM / VistaTM 64-bit / 7 /

7 64-bit Without RAID Functions ............................................... 302.14.1 Installing Windows XP / XP 64-bit Without RAID

Functions ...................................................................... 302.14.2 Installing Windows VistaTM / VistaTM 64-bit / 7 / 7 64-bit

Without RAID Functions ................................................ 312.15 Untied Overclocking Technology ................................................ 32

44444

3 .3 .3 .3 .3 . BIOS SBIOS SBIOS SBIOS SBIOS SETUP UTILITYETUP UTILITYETUP UTILITYETUP UTILITYETUP UTILITY .......................................................................................................................................................................................................................................................... 33 33 33 33 333.1 Introduction ................................................................................ 33

3.1.1 BIOS Menu Bar ............................................................... 333.1.2 Navigation Keys .............................................................. 34

3.2 Main Screen .............................................................................. 343.3 OC Tweaker Screen ................................................................... 353.4 Advanced Screen ....................................................................... 40

3.4.1 CPU Configuration ........................................................... 413.4.2 Chipset Configuration ...................................................... 423.4.3 ACPI Configuration .......................................................... 433.4.4 Storage Configuration ...................................................... 443.4.5 PCIPnP Configuration ...................................................... 463.4.6 Floppy Configuration ........................................................ 473.4.7 Super IO Configuration .................................................... 473.4.8 USB Configuration ........................................................... 49

3.5 Hardware Health Event Monitoring Screen ................................. 503.6 Boot Screen .............................................................................. 51

3.6.1 Boot Settings Configuration ............................................. 513.7 Security Screen ......................................................................... 523.8 Exit Screen ................................................................................ 53

4 .4 .4 .4 .4 . Software SupportSoftware SupportSoftware SupportSoftware SupportSoftware Support ............................................................................................................................................................................................................................................................... 54 54 54 54 544.1 Install Operating System ........................................................... 544.2 Support CD Information .............................................................. 54

4.2.1 Running Support CD ........................................................ 544.2.2 Drivers Menu ................................................................... 544.2.3 Utilities Menu .................................................................. 544.2.4 Contact Information .......................................................... 54

55555

1.1.1.1.1. IntroductionIntroductionIntroductionIntroductionIntroductionThank you for purchasing DIGILITE DL-960GM-GS3-FX motherboard, a reliablemotherboard produced under DIGILITEs consistently stringent quality control. It deliversexcellent performance with robust design conforming to DIGILITEs commitment to qual-ity and endurance.

Because the motherboard specifications and the BIOS software might beupdated, the content of this manual will be subject to change withoutnotice. In case any modifications of this manual occur, the updatedversion will be available on DIGILITE website without further notice.If you require technical support related to this motherboard, please visitour website for specific information about the model you are using.

1.11 .11 .11 .11 .1 PPPPPackackackackackage Contentsage Contentsage Contentsage Contentsage ContentsDIGILITE DL-960GM-GS3-FX Motherboard

(Micro ATX Form Factor: 9.6-in x 7.2-in, 24.4 cm x 18.3 cm)DIGILITE DL-960GM-GS3-FX Quick Installation GuideDIGILITE DL-960GM-GS3-FX Support CD2 x Serial ATA (SATA) Data Cables (Optional)1 x I/O Panel Shield

66666

1 .21 .21 .21 .21 .2 SpecificationsSpecificationsSpecificationsSpecificationsSpecifications

Platform - Micro ATX Form Factor: 9.6-in x 7.2-in, 24.4 cm x 18.3 cm- Solid Capacitor for CPU power

CPU - Support for Socket AM3+ processors- Support for Socket AM3 processors: AMD PhenomTM II X6 / X4 / X3 / X2 (except 920 / 940) / Athlon II X4 / X3 / X2 / Sempron processors- Supports 8-Core CPU- AMD LIVE!TM Ready- Supports AMDs Cool n QuietTM Technology- FSB 2600 MHz (5.2 GT/s)- Supports Untied Overclocking Technology (see CAUTION 1)- Supports Hyper-Transport 3.0 (HT 3.0) Technology

Chipset - Northbridge: AMD 760G- Southbridge: AMD SB710

Memory - Dual Channel DDR3 Memory Technology (see CAUTION 2)- 2 x DDR3 DIMM slots- Support DDR3 1800(OC)/1600(OC)/1333/1066/800 non-ECC, un-buffered memory (see CAUTION 3)- Max. capacity of system memory: 8GB (see CAUTION 4)

Expansion Slot - 1 x PCI Express 2.0 x16 slot (blue @ x16 mode)- 1 x PCI Express 2.0 x1 slot- 2 x PCI slots

Graphics - Integrated AMD Radeon HD 3000 graphics- DX10 class iGPU, Pixel Shader 4.0- Max. shared memory 512MB (see CAUTION 5)- Supports D-Sub with max. resolution up to 2048x1536 @ 60Hz

Audio - 5.1 CH HD Audio (Realtek ALC662 Audio Codec) LAN - Realtek PCIE x1 Gigabit LAN RTL8111E

- Speed 10/100/1000 Mb/s- Supports Wake-On-LAN- Supports PXE

Rear Panel I/O I/O Panel- 1 x PS/2 Mouse Port- 1 x PS/2 Keyboard Port- 1 x Serial Port: COM1- 1 x VGA Port- 4 x Ready-to-Use USB 2.0 Ports- 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)

77777

- HD Audio Jack: Line in / Front Speaker / Microphone Connector - 4 x SATA2 3.0Gb/s connectors, support RAID (RAID 0, RAID 1,

RAID 10 and JBOD), NCQ, AHCI and Hot Plug functions (see CAUTION 6)- 1 x ATA133 IDE connector (supports 2 x IDE devices)- 1 x Floppy connector- 1 x Print port header- CPU/Chassis/Power FAN connector- 24 pin ATX power connector- 4 pin 12V power connector- Front panel audio connector- 2 x USB 2.0 headers (support 4 USB 2.0 ports)

BIOS Feature - 8Mb AMI BIOS- AMI Legal BIOS- Supports Plug and Play- ACPI 1.1 Compliance Wake Up Events- Supports jumperfree- SMBIOS 2.3.1 Support- CPU, VCCM, NB Voltage Multi-adjustment

Support CD - Drivers, Utilities Unique Feature - Instant Flash (see CAUTION 7)

- Hybrid Booster:- CPU Frequency Stepless Control (see CAUTION 8)- U-COP (see CAUTION 9)- Boot Failure Guard (B.F.G.)

Hardware - CPU Temperature Sensing Monitor - Chassis Temperature Sensing

- CPU/Chassis/Power Fan Tachometer- CPU Quiet Fan- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP Media Center / XP 64-bit compliant

Certifications - FCC, CE, WHQL- ErP/EuP Ready (ErP/EuP ready power supply is required) (see CAUTION 10)

* For detailed product information, please visit our website.

88888

WARNINGPlease realize that there is a certain risk involved with overclocking, includingadjusting the setting in the BIOS, applying Untied Overclocking Technology, or usingthe third-party overclocking tools. Overclocking may affect your system stability, oreven cause damage to the components and devices of your system. It should bedone at your own risk and expense. We are not responsible for possible damagecaused by overclocking.

99999

CAUTION!1. This motherboard supports Untied Overclocking Technology. Please read

Untied Overclocking Technology on page 32 for details.2. This motherboard supports Dual Channel Memory Technology. Before

you implement Dual Channel Memory Technology, make sure to readthe installation guide of memory modules on page 15 of User Manualin the support CD for proper installation.

3. Whether 1800/1600MHz memory speed is supported depends on theAM3/AM3+ CPU you adopt. If you want to adopt DDR3 1800/1600 memorymodule on this motherboard, please refer to the memory support list onour website for the compatible memory modules.

4. Due to the operating system limitation, the actual memory size may beless than 4GB for the reservation for system usage under Windows 7/ VistaTM / XP. For Windows OS with 64-bit CPU, there is no suchlimitation.

5. The maximum shared memory size is defined by the chipset vendorand is subject to change. Please check AMD website for the latestinformation.

6. Before installing SATAII hard disk to SATAII connector, please read the SATAIIHard Disk Setup Guide on page 24 of User Manual in the support CD toadjust your SATAII hard disk drive to SATAII mode. You can also connectSATA hard disk to SATAII connector directly.

7. Instant Flash is a BIOS flash utility embedded in Flash ROM. This conve-nient BIOS update tool allows you to update system BIOS without enter-ing operating systems first like MS-DOS or Windows. With this utility,you can press key during the POST or press key to BIOSsetup menu to access Instant Flash. Just launch this tool and save thenew BIOS file to your USB flash drive, floppy disk or hard drive, then youcan update your BIOS only in a few clicks without preparing an addi-tional floppy diskette or other complicated flash utility. Please be notedthat the USB flash drive or hard drive must use FAT32/16/12 file system.

8. Although this motherboard offers stepless control, it is not recom-mended to perform over-clocking. Frequencies other than the recom-mended CPU bus frequencies may cause the instability of the systemor damage the CPU.

9. While CPU overheat is detected, the system will automatically shutdown.Before you resume the system, please check if the CPU fan on themotherboard functions properly and unplug the power cord, then plug itback again. To improve heat dissipation, remember to spray thermalgrease between the CPU and the heatsink when you install the PCsystem.

1010101010

10. EuP, stands for Energy Using Product, was a provision regulated by Euro-pean Union to define the power consumption for the completed system.According to EuP, the total AC power of the completed system shall beunder 1.00W in off mode condition. To meet EuP standard, an EuP readymotherboard and an EuP ready power supply are required. According toIntels suggestion, the EuP ready power supply must meet the standard of5v standby power efficiency is higher than 50% under 100 mA currentconsumption. For EuP ready power supply selection, we recommend youchecking with the power supply manufacturer for more details.

1111111111

1.3 Motherboard Layout1.3 Motherboard Layout1.3 Motherboard Layout1.3 Motherboard Layout1.3 Motherboard Layout

1 PS2_USB_PW1 Jumper 15 System Panel Header (PANEL1, White) 2 ATX 12V Power Connector (ATX12V1) 16 Secondary SATAII Connector 3 CPU Heatsink Retention Module (SATAII_2 (PORT 1)) 4 AM3 CPU Socket 17 Primary SATAII Connector 5 2 x 240-pin DDR3 DIMM Slots (SATAII_1 (PORT 0))

(Dual Channel: DDR3_A1, DDR3_B1; Blue) 18 USB 2.0 Header (USB4_5, Blue) 6 CPU Fan Connector (CPU_FAN1) 19 USB 2.0 Header (USB6_7, Blue) 7 ATX Power Connector (ATXPWR1) 20 Chassis Fan Connector (CHA_FAN1) 8 Chassis Speaker Header 21 Floppy Connector (FLOPPY1)

(SPEAKER 1, White) 22 Print Port Header (LPT1, White) 9 Clear CMOS Jumper (CLRCMOS1) 23 Front Panel Audio Header10 Primary IDE Connector (IDE1, Blue) (HD_AUDIO1, White)11 Northbridge Controller 24 PCI Slots (PCI1- 2)12 Southbridge Controller 25 SPI Flash Memory (8Mb)13 Third SATAII Connector (SATAII_3 (PORT 2)) 26 PCI Express 2.0 x16 Slot (PCIE2; Blue)14 Fourth SATAII Connector (SATAII_4 (PORT 3)) 27 PCI Express 2.0 x1 Slot (PCIE1; Blue)

28 Power Fan Connector (PWR_FAN1)

S upe rI/O

CMOSBATTER Y

ATXPWR1

SOCKETAM3

AMD760G

C hipset

PS2_USB_PW1

1

PCIE 1

PCI1

PCI2

LA N

AUDI OCODE C

1

CLRCMOS 1

CPU_FAN1

HDLE

DRES

ET

PLED

PWRB

TN

1

PANE L 1

CHA_FAN1

SPEAKER1

1

IDE1

FLOPPY1

HD_AUDIO1

1

RoHS24

.4cm

(9.6-in

)

18.3cm (7.2-in)

5 61 2 3 4

7

9

10

11

1213

14

15

16171819202122

23

24

25

26

27

8MbB IOS

HT3.

0

AMDS B710C hipset

SA TA II_ 3(

SA TA II_ 4PORT 2) (POR T 3 )

USB4_5

1

USB6_7

1

PCIE 2

DDR3

1800

Top:LIN

EIN

Center:FRO

NT

Bottom:

MIC

IN

PS2Mouse

PS2Keyboard

US B 2 .0T: USB0B: USB1

Top:RJ-4 5

US B 2 .0T: USB 2B: USB 3

)6%

DDR3_A1

(64bit, 2

40-pin

module

)

DDR3_B1

(64bit, 2

40-pin

module

)Dual Channe l

AM3+

FSB2

.6GH

z

Phenom II

Support8-CoreCPU

ErP/Eu

PRe

ady

VGA1

COM1 AT X 12V 1

1LPT1

SA TA II_ 1 ( PORT 0) SA TA II_ 2 ( PORT 1)

DX1

0

8

PWR_

FAN1

28

Des

ign

inTa

ipei

DL-960GM-GS3-F X

1212121212

1.4 I/O P1.4 I/O P1.4 I/O P1.4 I/O P1.4 I/O Panelanelanelanelanel

1 PS/2 Mouse Port (Green) 6 Microphone (Pink)2 USB 2.0 Ports (USB23) 7 USB 2.0 Ports (USB01)

* 3 RJ-45 Port 8 VGA Port4 Line In (Light Blue) 9 COM Port5 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front panel audio header. Please refer to below steps for the software setting of Multi-Streaming. For Windows XP: After restarting your computer, you will find Mixer tool on your system. Please select Mixer ToolBox , click Enable playback multi-streaming, and click ok. Choose 2CH or

4CH and then you are allowed to select Realtek HDA Primary output to use Rear Speaker and Front Speaker, or select Realtek HDA Audio 2nd output to use front panel audio. Then reboot your system. For Windows 7 / VistaTM: After restarting your computer, please double-click Realtek HD Audio Manager on the system tray. Set Speaker Configuration to Quadraphonic or Stereo. Click Device advanced settings, choose Make front and rear output devices playbacks two different audio streams simultaneously, and click ok. Then reboot your system.

1 2

4

3

5

6

78910

* There are two LED next to the LAN port. Please refer to the table below for the LAN port LED indications.

LAN Port LED Indications Activity/Link LED SPEED LEDStatus Description Status DescriptionOff No Activity Off 10Mbps connectionBlinking Data Activity Orange 100Mbps connection

Green 1Gbps connectionLAN Port

ACT/LINK LED

SPEED LED

1313131313

2.2.2.2.2. InstallationInstallationInstallationInstallationInstallationThis is a Micro ATX form factor (9.6-in x 7.2-in, 24.4 cm x 18.3 cm) motherboard.Before you install the motherboard, study the configuration of your chassis to en-sure that the motherboard fits into it.

Pre-installation PrecautionsPre-installation PrecautionsPre-installation PrecautionsPre-installation PrecautionsPre-installation PrecautionsTake note of the following precautions before you install motherboardcomponents or change any motherboard settings.

Before you install or remove any component, ensure that thepower is switched off or the power cord is detached from thepower supply. Failure to do so may cause severe damage to themotherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching anycomponent.

2. To avoid damaging the motherboard components due to staticelectricity, NEVER place your motherboard directly on the carpet orthe like. Also remember to use a grounded wrist strap or touch asafety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.4. Whenever you uninstall any component, place it on a grounded anti-

static pad or in the bag that comes with the component.5. When placing screws into the screw holes to secure the motherboard

to the chassis, please do not over-tighten the screws! Doing so maydamage the motherboard.

1414141414

2.12.12.12.12.1 CPU InstallationCPU InstallationCPU InstallationCPU InstallationCPU InstallationStep 1. Unlock the socket by lifting the lever up to a 90o angle.Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPUinto the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you pushdown the socket lever to secure the CPU. The lever clicks on the side tabto indicate that it is locked.

2.22.22.22.22.2 Installation of CPU Fan and HeatsinkInstallation of CPU Fan and HeatsinkInstallation of CPU Fan and HeatsinkInstallation of CPU Fan and HeatsinkInstallation of CPU Fan and Heatsink

After you install the CPU into this motherboard, it is necessary to install alarger heatsink and cooling fan to dissipate heat. You also need to spraythermal grease between the CPU and the heatsink to improve heatdissipation. Make sure that the CPU and the heatsink are securely fas-tened and in good contact with each other. Then connect the CPU fan tothe CPU FAN connector (CPU_FAN1, see Page 11, No. 6). For properinstallation, please kindly refer to the instruction manuals of the CPU fanand the heatsink.

STEP 1:

Lift Up The Socket Lever

STEP 2 / STEP 3:Match The CPU Golden TriangleTo The Socket Corner SmallTriangle

STEP 4:Push Down And LockThe Socket Lever

Lever 90 Up

CPU Golden Triangle

Socker Corner Small Triangle

1515151515

2.3 Installation of Memor2.3 Installation of Memor2.3 Installation of Memor2.3 Installation of Memor2.3 Installation of Memory Modules (DIMM)y Modules (DIMM)y Modules (DIMM)y Modules (DIMM)y Modules (DIMM)DL-960GM-GS3-FX motherboard provides two 240-pin DDR3 (Double Data Rate 3) DIMMslots, and supports Dual Channel Memory Technology. For dual channel configuration,you always need to install two identical (the same brand, speed, size and chip-type)memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology.Otherwise, it will operate at single channel mode.

1. It is not allowed to install a DDR or DDR2 memory module intoDDR3 slot;otherwise, this motherboard and DIMM may be damaged.

2. If you install only one memory module or two non-identical memorymodules, it is unable to activate the Dual Channel Memory Technology.

Installing a DIMMInstalling a DIMMInstalling a DIMMInstalling a DIMMInstalling a DIMM

Please make sure to disconnect power supply before adding orremoving DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanentdamage to the motherboard and the DIMM if you force the DIMM into theslot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fullysnap back in place and the DIMM is properly seated.

notch

break

notchbreak

1616161616

2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)2.4 Expansion Slots (PCI and PCI Express Slots)There are 2 PCI slots and 2 PCI Express slots on this motherboard.PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.PCIE slots:

PCIE1 (PCIE x1 slot; Blue) is used for PCI Express cards with x1 lanewidth cards, such as Gigabit LAN card, SATA2 card, etc.PCIE2 (PCIE x16 slot; Blue) is used for PCI Express cards with x16lane width graphics cards.

Installing an expansion cardInstalling an expansion cardInstalling an expansion cardInstalling an expansion cardInstalling an expansion cardStep 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read thedocumentation of the expansion card and make necessary hardwaresettings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screwsfor later use.

Step 3. Align the card connector with the slot and press firmly until the card iscompletely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

1717171717

2.5 Multi Monitor Feature2.5 Multi Monitor Feature2.5 Multi Monitor Feature2.5 Multi Monitor Feature2.5 Multi Monitor FeatureThis motherboard supports multi monitor feature. With the internal VGA outputsupport and the external add-on PCI Express VGA card, you can easily enjoy thebenefits of multi monitor feature.Please refer to the following steps to set up a surround display environment:

1. Install the ATITM PCI Express VGA cards on PCIE2 slot. Please refer to page 16 for proper expansion card installation procedures for details.2. Connect D-Sub monitor cable to VGA port on the I/O panel. And connect other monitor cables to the corresponding connectors of the add-on PCI Express VGA cards on PCIE2 slot.

VGA port

3. Boot your system. Press to enter BIOS setup. Enter Share Memory option to adjust the memory capability to [32MB], [64MB], [128MB] [256MB] or [512MB] to enable the function of VGA. Please make sure that the value you select is less than the total capability of the system memory. If you do not adjust the BIOS setup, the default value of Share Memory, [Auto], will disable VGA function when the add-on VGA card is inserted to this motherboard.4. Install the onboard VGA driver and the add-on PCI Express VGA card driver to your system. If you have installed the drivers already, there is no need to install them again.5. Set up a multi-monitor display.

For Windows XP / XP 64-bit OS:Right click the desktop, choose Properties, and select the Settings tabso that you can adjust the parameters of the multi-monitor according to thesteps below.A. Click the Identify button to display a large number on each monitor.B. Right-click the display icon in the Display Properties dialog that you wish to be your primary monitor, and then select Primary. When you use multiple monitors with your card, one monitor will always be Primary, and all additional monitors will be designated as Secondary.C. Select the display icon identified by the number 2.D. Click Extend my Windows desktop onto this monitor.

1818181818

E. Right-click the display icon and select Attached, if necessary.F. Set the Screen Resolution and Color Quality as appropriate for the second monitor. Click Apply or OK to apply these new values.G. Repeat steps C through E for the diaplay icon identified by the number one, two and three.

For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS:Right click the desktop, choose Personalize, and select the DisplaySettings tab so that you can adjust the parameters of the multi-monitoraccording to the steps below.A. Click the number 2 icon.B. Click the items This is my main monitor and Extend the desktop onto this monitor.C. Click OK to save your change.D. Repeat steps A through C for the display icon identified by the number three.

6. Use multi monitor feature. Click and drag the display icons to positions representing the physical setup of your monitors that you would like to use. The placement of display icons determines how you move items from one monitor to another.

1919191919

+5V

1_2

+5VSB

2_3

2.62.62.62.62.6 Jumpers SetupJumpers SetupJumpers SetupJumpers SetupJumpers SetupThe illustration shows how jumpers are setup.When the jumper cap is placed on pins, thejumper is Short. If no jumper cap is placed onpins, the jumper is Open. The illustrationshows a 3-pin jumper whose pin1 andpin2 are Short when jumper cap is placed onthese 2 pins.

Jumper SettingPS2_USB_PW1 Short pin2, pin3 to enable(see p.11, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

Clear CMOS Jumper(CLRCMOS1)

(see p.11, No. 9)

Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includessystem setup information such as system password, date, time, and systemsetup parameters. To clear and reset the system parameters to default setup,please turn off the computer and unplug the power cord from the powersupply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS rightafter you update the BIOS. If you need to clear the CMOS when you just finishupdating the BIOS, you must boot up the system first, and then shut it downbefore you do the clear-CMOS action.

Clear CMOS

2_31_2

Default

2020202020

FLOPPY1Pin1

the red-striped side to Pin1

2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors2.7 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT placejumper caps over these headers and connectors. Placing jumper capsover the headers and connectors will cause permanent damage of themotherboard!

Floppy Connector(33-pin FLOPPY1)

(see p.11 No. 21)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of theconnector.

Primary IDE connector (Blue)(39-pin IDE1, see p.11 No. 10)

Note: Please refer to the instruction of your IDE device vendor for the details.

Serial ATAII Connectors These four Serial ATAII (SATAII)(SATAII_1 (PORT 0): connectors support SATAIIsee p.11, No. 17) or SATA hard disk for internal(SATAII_2 (PORT 1): storage devices. The currentsee p.11, No. 16) SATAII interface allows up to(SATAII_3 (PORT 2): 3.0 Gb/s data transfer rate.see p.11, No. 13)(SATAII_4 (PORT 3):see p.11, No. 14)

connect the black endto the IDE devices

connect the blue endto the motherboard

IDE1PIN1

80-conductor ATA 66/100/133 cable

SATAII_3 SATAII_4(PORT 2) (PORT 3)

Serial ATA (SATA) Either end of the SATA data cableData Cable can be connected to the SATA /(Optional) SATAII hard disk or the SATAII

connector on this motherboard.

SATAII_1 SATAII_2(PORT 0) (PORT 1)

2121212121

J_SENSE

OUT2_L

1

MIC_RETPRESENCE#

GND

OUT2_RMIC2_R

MIC2_L

OUT_RET

Front Panel Audio Header This is an interface for the front(9-pin HD_AUDIO1) panel audio cable that allows(see p.11, No. 23) convenient connection and

control of audio devices.

USB 2.0 Headers Besides four default USB 2.0(9-pin USB6_7) ports on the I/O panel, there are(see p.11 No. 19) two USB 2.0 headers on this

motherboard. Each USB 2.0header can support two USB2.0 ports.

(9-pin USB4_5)(see p.11 No. 18)

USB_PWR

USB_PWR

P+7P-7

P+6P-6

GND

GND

DUMMY

1

USB_PWR

USB_PWR

P+5P-5

P+4P-4

GND

GND

DUMMY

1

Print Port Header This is an interface for print(25-pin LPT1) port cable that allows(see p.11 No. 22) convenient connection of printer

devices.1

AFD#ERROR#

PINIT#GNDSLIN#

STB#SPD0

SPD1SPD2

SPD3SPD4

SPD5SPD6

SPD7ACK#

BUSYPE

SLCT

1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the

instruction in our manual and chassis manual to install your system.2. If you use AC97 audio panel, please install it to the front panel audio header as below: A. Connect Mic_IN (MIC) to MIC2_L. B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.

C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You dont need to connect them for AC97 audio panel.

E. To activate the front mic. For Windows XP / XP 64-bit OS: Select Mixer. Select Recorder. Then click FrontMic. For Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust Recording Volume.

2222222222

20-Pin ATX Power Supply Installation

Though this motherboard provides 24-pin ATX power connector, it can still work if you adopt a traditional 20-pin ATX power supply. To use the 20-pin ATX power supply, please plug your power supply along with Pin 1 and Pin 13.

ATX Power Connector Please connect an ATX power(24-pin ATXPWR1) supply to this connector.(see p.11 No. 7)

12

1

24

13

12

1

24

13

CPU Fan Connector Please connect the CPU fan(4-pin CPU_FAN1) cable to this connector and(see p.11 No. 6) match the black wire to the

ground pin.

Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.

3-Pin Fan Installation

Pin 1-3 Connected

+5V

DUMMYDUMMY

SPEAKER

1

GND

PWRBTN#PLED-

PLED+

DUMMYRESET#

GND

HDLED+HDLED-

1

System Panel Header This header accommodates(9-pin PANEL1) several system front panel(see p.11 No. 15) functions.

Chassis Speaker Header Please connect the chassis(4-pin SPEAKER 1) speaker to this header.(see p.11 No. 8)

Chassis and Power Fan Connectors Please connect the fan cables(4-pin CHA_FAN1) to the fan connectors and(see p.11 No. 20) match the black wire to the

(3-pin PWR_FAN1)(see p.11 No. 28)

GND

+12V

CPU_FAN_SPEED

FAN_SPEED_CONTROL

1234

PWR_FAN_SPEED

GND

+12V

FAN_SPEEDFAN_SPEED_CONTROL

+12VGND

2323232323

ATX 12V Power Connector Please connect an ATX 12V(4-pin ATX12V1) power supply to this connector.(see p.11 No. 2)

2424242424

2.82.82.82.82.8 SASASASASATTTTTAII Hard Disk Setup GuideAII Hard Disk Setup GuideAII Hard Disk Setup GuideAII Hard Disk Setup GuideAII Hard Disk Setup GuideBefore installing SATAII hard disk to your computer, please carefully read belowSATAII hard disk setup guide. Some default setting of SATAII hard disks may not beat SATAII mode, which operate with the best performance. In order to enable SATAIIfunction, please follow the below instruction with different vendors to correctly adjustyour SATAII hard disk to SATAII mode in advance; otherwise, your SATAII hard diskmay fail to run at SATAII mode.

Western Digital

If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.On the other hand, if you want to enable SATAII 3.0Gb/s, please remove thejumpers from pin 5 and pin 6.

SAMSUNG

If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.On the other hand, if you want to enable SATAII 3.0Gb/s, please remove thejumpers from pin 3 and pin 4.

HITACHIPlease use the Feature Tool, a DOS-bootable tool, for changing various ATAfeatures. Please visit HITACHIs website for details:http://www.hitachigst.com/hdd/support/download.htm

1357

2468

1357

2468

The above examples are just for your reference. For different SATAII harddisk products of different vendors, the jumper pin setting methods may notbe the same. Please visit the vendors website for the updates.

2525252525

2.10 Hot Plug and Hot Swap F2.10 Hot Plug and Hot Swap F2.10 Hot Plug and Hot Swap F2.10 Hot Plug and Hot Swap F2.10 Hot Plug and Hot Swap Functions for SAunctions for SAunctions for SAunctions for SAunctions for SATTTTTA / SAA / SAA / SAA / SAA / SATTTTTAIIAIIAIIAIIAII

HDDsHDDsHDDsHDDsHDDsThis motherboard supports Hot Plug and Hot Swap functions for SATA / SATAIIDevices in RAID / AHCI mode. AMD SB710 south bridge chipset provides hardwaresupport for Advanced Host controller Interface (AHCI), a new programming interfacefor SATA host controllers developed thru a joint industry effort. AHCI also providesusability enhancements such as Hot Plug.

NOTEWhat is Hot Plug Function?If the SATA / SATAII HDDs are NOT set for RAID configuration, it is calledHot Plug for the action to insert and remove the SATA / SATAII HDDswhile the system is still power-on and in working condition.However, please note that it cannot perform Hot Plug if the OS has beeninstalled into the SATA / SATAII HDD.

What is Hot Swap Function?If SATA / SATAII HDDs are built as RAID 1 then it is called Hot Swap forthe action to insert and remove the SATA / SATAII HDDs while the systemis still power-on and in working condition.

2.92.92.92.92.9 Serial ASerial ASerial ASerial ASerial ATTTTTA (SAA (SAA (SAA (SAA (SATTTTTA) / Serial AA) / Serial AA) / Serial AA) / Serial AA) / Serial ATTTTTAII (SAAII (SAAII (SAAII (SAAII (SATTTTTAII) Hard DisksAII) Hard DisksAII) Hard DisksAII) Hard DisksAII) Hard Disks

Instal lat ionInstal lat ionInstal lat ionInstal lat ionInstal lat ionThis motherboard adopts AMD SB710 south bridge chipset that supports SerialATA (SATA) / Serial ATAII (SATAII) hard disks and RAID (RAID 0, RAID 1, RAID 10and JBOD) functions. You may install SATA / SATAII hard disks on thismotherboard for internal storage devices. This section will guide you to install theSATA / SATAII hard disks.

STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.STEP 3: Connect one end of the SATA data cable to the motherboards SATAII

connector.STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard

disk.

If you plan to use RAID 0 or RAID 1 function, you need to install at least 2SATA / SATAII hard disks. If you plan to use RAID 10 function, you need toinstall 4 SATA / SATAII hard disks.

2626262626

Caution1. Without SATA 15-pin power connector interface, the SATA / SATAII Hot Plug cannot be processed.2. Even some SATA / SATAII HDDs provide both SATA 15-pin power connector and IDE 1x4-pin conventional power connector interfaces, the IDE 1x4-pin conventional power connector interface is definitely not able to support Hot Plug and will cause the HDD damage and data loss.

SATA 7-pinconnector

1x4-pin conventionalpower connector (White)connect to power supply

A. SATA data cable (Red) B. SATA power cable

2.11 SA2.11 SA2.11 SA2.11 SA2.11 SATTTTTA / SAA / SAA / SAA / SAA / SATTTTTAII HDD Hot Plug FAII HDD Hot Plug FAII HDD Hot Plug FAII HDD Hot Plug FAII HDD Hot Plug Feature and Operationeature and Operationeature and Operationeature and Operationeature and Operation

GuideGuideGuideGuideGuideThis motherboard supports Hot Plug feature for SATA / SATAII HDD in RAID / AHCImode. Please read below operation guide of SATA / SATAII HDD Hot Plug feature carefully.Before you process the SATA / SATAII HDD Hot Plug, please check below cableaccessories from the motherboard gift box pack.A. 7-pin SATA data cableB. SATA power cable with SATA 15-pin power connector interface

The SATA 15-pin powerconnector (Black) connectto SATA / SATAII HDD

Points of attention, before you process the Hot Plug:1. Below operation procedure is designed only for our motherboard, which supports SATA / SATAII HDD Hot Plug. * The SATA / SATAII Hot Plug feature might not be supported by the chipset because of its limitation, the SATA / SATAII Hot Plug support information of our motherboard is indicated in the product spec on our website.2. Make sure your SATA / SATAII HDD can support Hot Plug function from your dealer or HDD user manual. The SATA / SATAII HDD, which cannot support Hot Plug function, will be damaged under the Hot Plug operation.3. Please make sure the SATA / SATAII driver is installed into system properly. The latest SATA / SATAII driver is available on our support website.4. Make sure to use the SATA power cable & data cable, which are from our motherboard package.5. Please follow below instructions step by step to reduce the risk of HDD crash or data loss.

2727272727

How to Hot Plug a SATA / SATAII HDD:Points of attention, before you process the Hot Plug:Please do follow below instruction sequence to process the Hot Plug, improperprocedure will cause the SATA / SATAII HDD damage and data loss.

Connect SATA data cable tothe motherboards SATAII connector.

Connect SATA 15-pin power cable connector(Black) end to SATA / SATAII HDD.

Connect SATA data cable tothe SATA / SATAII HDD.

How to Hot Unplug a SATA / SATAII HDD:

Points of attention, before you process the Hot Unplug:Please do follow below instruction sequence to process the Hot Unplug, improperprocedure will cause the SATA / SATAII HDD damage and data loss.

Please connect SATA power cable 1x4-pin end(White) to the power supply 1x4-pin cable.

Step 1 Step 2

Step 3 Step 4

Step 2

SATA power cable 1x4-pinpower connector (White)

Unplug SATA data cable from SATA / SATAII HDD side.

Unplug SATA 15-pin power cable connector (Black) from SATA / SATAII HDD side.

Step 1

2828282828

2.122.122.122.122.12 Driver Installation GuideDriver Installation GuideDriver Installation GuideDriver Installation GuideDriver Installation GuideTo install the drivers to your system, please insert the support CD to your opticaldrive first. Then, the drivers compatible to your system can be auto-detected andlisted on the support CD driver page. Please follow the order from up to bottomside to install those required drivers. Therefore, the drivers you install can workproperly.

2.132.132.132.132.13 Installing WindowsInstalling WindowsInstalling WindowsInstalling WindowsInstalling Windows 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / VistaTMTMTMTMTM / Vista / Vista / Vista / Vista / VistaTMTMTMTMTM

64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit With RAID Fith RAID Fith RAID Fith RAID Fith RAID FunctionsunctionsunctionsunctionsunctionsIf you want to install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit ona RAID disk composed of 2 or more SATA / SATAII HDDs with RAID functions, pleasefollow below procedures according to the OS you install.

2.13.1 Installing Windows2.13.1 Installing Windows2.13.1 Installing Windows2.13.1 Installing Windows2.13.1 Installing Windows XP / XP 64-bit With RAID XP / XP 64-bit With RAID XP / XP 64-bit With RAID XP / XP 64-bit With RAID XP / XP 64-bit With RAID

Functions Functions Functions Functions FunctionsIf you want to install Windows XP / XP 64-bit on a RAID disk composed of 2 or moreSATA / SATAII HDDs with RAID functions, please follow below steps.

STEP 1: Set up BIOS.A. Enter BIOS SETUP UTILITY Advanced screen Storage

Configuration.B. Set the SATA Operation Mode option to [RAID].STEP 2: Make a SATA / SATAII Driver Diskette.A. Insert the Support CD into your optical drive to boot your system.B. During POST at the beginning of system boot-up, press key, and

then a window for boot devices selection appears. Please select CD-ROM as the boot device.

C. When you see the message on the screen, Generate Serial ATA driverdiskette [YN]?, press .

D. Then you will see these messages,Please insert a blankformatted diskette into floppydrive A:press any key to start

Please insert a floppy diskette into the floppy drive, and press any key.E. The system will start to format the floppy diskette and copy SATA /

SATAII drivers into the floppy diskette.

2929292929

NOTE. If you install Windows XP / XP 64-bit on IDE HDDs and want to manage (create,convert, delete, or rebuild) RAID functions on SATA / SATAII HDDs, you still need toset up SATA Operation Mode to [RAID] first. Then, please set the RAID configuration.

2.13.2 Installing Windows2.13.2 Installing Windows2.13.2 Installing Windows2.13.2 Installing Windows2.13.2 Installing Windows 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / VistaTMTMTMTMTM / Vista / Vista / Vista / Vista / VistaTMTMTMTMTM

64-bit W 64-bit W 64-bit W 64-bit W 64-bit With RAID Fith RAID Fith RAID Fith RAID Fith RAID FunctionsunctionsunctionsunctionsunctionsIf you want to install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit on a RAID diskcomposed of 2 or more SATA / SATAII HDDs with RAID functions, please follow belowsteps.


Configuration.B. Set the SATA Operation Mode option to [RAID].STEP 2: Use RAID Installation Guide to set RAID configuration.Before you start to configure RAID function, you need to check the RAID installationguide in the Support CD for proper configuration. Please refer to the BIOS RAIDinstallation guide part of the document in the following path in the Support CD:.. \ RAID Installation GuideSTEP 3: Install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

system.

STEP 3: Use RAID Installation Guide to set RAID configuration.Before you start to configure RAID function, you need to check the RAID installationguide in the Support CD for proper configuration. Please refer to the BIOS RAIDinstallation guide part of the document in the following path in the Support CD:.. \ RAID Installation GuideSTEP 4: Install Windows XP / XP 64-bit OS on your system.After step 1, 2, 3, you can start to install Windows XP / XP 64-bit OS on your system.At the beginning of Windows setup, press F6 to install a third-party RAID driver.When prompted, insert the SATA / SATAII driver diskette containing the AMD RAIDdriver. After reading the floppy disk, the driver will be presented. Select the driver toinstall according to the OS you install. (Select AMD AHCI Compatible RAID Controller-x86 platform for Windows XP, or AMD AHCI Compatible RAID Controller-x64 plat-form for Windows XP 64-bit.)

3030303030

NOTE1. If you install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit on IDE HDDsand want to manage (create, convert, delete, or rebuild) RAID functions on SATA /SATAII HDDs, you still need to set up SATA Operation Mode to [RAID] in BIOS first.Then, please set the RAID configuration.

NOTE2. Currently, if you install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit onIDE HDDs and there are no SATA / SATAII device used, please set up SATAOperation Mode to [IDE] in BIOS.

2.142.142.142.142.14 Installing WindowsInstalling WindowsInstalling WindowsInstalling WindowsInstalling Windows 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / VistaTMTMTMTMTM / Vista / Vista / Vista / Vista / VistaTMTMTMTMTM

64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit W64-bit / XP / XP 64-bit Without RAID Fithout RAID Fithout RAID Fithout RAID Fithout RAID FunctionsunctionsunctionsunctionsunctionsIf you want to install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit OSon your SATA / SATAII HDDs without RAID functions, please follow below proceduresaccording to the OS you install.

2.14.1 Installing Windows2.14.1 Installing Windows2.14.1 Installing Windows2.14.1 Installing Windows2.14.1 Installing Windows XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID XP / XP 64-bit Without RAID

Functions Functions Functions Functions FunctionsIf you want to install Windows XP / XP 64-bit on your SATA / SATAII HDDs withoutRAID functions, please follow below steps.

Using SATA / SATAII HDDs with NCQ and Hot Plug functions (AHCI mode)

STEP 1: Set Up BIOS.A. Enter BIOS SETUP UTILITY Advanced screen Storage

Configuration.B. Set the SATA Operation Mode option to [AHCI].STEP 4: Install Windows XP / XP 64-bit OS on your system.You can start to install Windows XP / XP 64-bit OS on your system. At the beginningof Windows setup, press F6 to install a third-party AHCI driver. When prompted,insert the SATA / SATAII driver diskette containing the AMD AHCI driver. After readingthe floppy disk, the driver will be presented. Select the driver to install according tothe OS you install. (Select AMD AHCI Compatible RAID Controller-x86 platform forWindows XP, or AMD AHCI Compatible RAID Controller-x64 platform for Windows

XP 64-bit.)

3131313131

Using SATA / SATAII HDDs without NCQ and Hot Plug functions (IDE mode)


Configuration.B. Set the SATA Operation Mode option to [IDE].STEP 2: Install Windows XP / XP 64-bit OS on your system.

2.14.2 Installing Windows2.14.2 Installing Windows2.14.2 Installing Windows2.14.2 Installing Windows2.14.2 Installing Windows 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / Vista 7 / 7 64-bit / VistaTMTMTMTMTM / Vista / Vista / Vista / Vista / VistaTMTMTMTMTM

64-bit W 64-bit W 64-bit W 64-bit W 64-bit Without RAID Fithout RAID Fithout RAID Fithout RAID Fithout RAID FunctionsunctionsunctionsunctionsunctionsIf you want to install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit on your SATA /SATAII HDDs without RAID functions, please follow below steps.

Using SATA / SATAII HDDs with NCQ and Hot Plug functions (AHCI mode)

STEP 1: Set Up BIOS.A. Enter BIOS SETUP UTILITY Advanced screen Storage

Configuration.B. Set the SATA Operation Mode option to [AHCI].STEP 2: Install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

system.


Configuration.B. Set the SATA Operation Mode option to [IDE].STEP 2: Install Windows 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS on your

system.

Using SATA / SATAII HDDs without NCQ and Hot Plug functions (IDE mode)

3232323232

2.152.152.152.152.15 Untied Overclocking TUntied Overclocking TUntied Overclocking TUntied Overclocking TUntied Overclocking TechnologyechnologyechnologyechnologyechnologyThis motherboard supports Untied Overclocking Technology, which means duringoverclocking, FSB enjoys better margin due to fixed PCI / PCIE buses. Before youenable Untied Overclocking function, please enter Overclock Mode option of BIOSsetup to set the selection from [Auto] to [Manual]. Therefore, CPU FSB is untiedduring overclocking, but PCI / PCIE buses are in the fixed mode so that FSB canoperate under a more stable overclocking environment.

Please refer to the warning on page 8 for the possible overclocking riskbefore you apply Untied Overclocking Technology.

3333333333

3.3.3.3.3. BIOS SETUP UTILITYBIOS SETUP UTILITYBIOS SETUP UTILITYBIOS SETUP UTILITYBIOS SETUP UTILITY3.1 Introduction3.1 Introduction3.1 Introduction3.1 Introduction3.1 IntroductionThis section explains how to use the BIOS SETUP UTILITY to configure your system.The SPI Memory on the motherboard stores the BIOS SETUP UTILITY. You may run theBIOS SETUP UTILITY when you start up the computer. Please press or during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise,POST will continue with its test routines.If you wish to enter the BIOS SETUP UTILITY after POST, restart the system bypressing + + , or by pressing the reset button on the systemchassis. You may also restart by turning the system off and then back on.

Because the BIOS software is constantly being updated, the followingBIOS setup screens and descriptions are for reference purpose only,and they may not exactly match what you see on your screen.

3.1.13.1.13.1.13.1.13.1.1 BIOS Menu BarBIOS Menu BarBIOS Menu BarBIOS Menu BarBIOS Menu BarThe top of the screen has a menu bar with the following selections:Main To set up the system time/date informationOC Tweaker To set up overclocking featuresAdvanced To set up the advanced BIOS featuresH/W Monitor To display current hardware statusBoot To set up the default system device to locate and load the

Operating SystemSecurity To set up the security featuresExit To exit the current screen or the BIOS SETUP UTILITYUse < > key or < > key to choose among the selections on the menu bar,and then press to get into the sub screen.

3434343434

BIOS SETUP UTILITY

Main OC Tweaker H/W Monitor Boot Security ExitAdvanced

Use [Enter], [TAB]or [SHIFT-TAB] toselect a field.

Use [+] or [-] toconfigure system Time.

Select ScreenSelect Item

+- Change FieldTab Select FieldF1 General HelpF9 Load DefaultsF10 Save and ExitESC Exit

v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.

System Overview

System Time

System Date[ :00:09][Tue 09/13/2011]

BIOS VersionProcessor Type

Processor SpeedMicrocode UpdateL1 Cache SizeL2 Cache Size

Total Memory

DDR3_A1DDR3_B1

: 960GM-GS3 FX P1.0: AMD Athlon(tm) II X2 235e

Processor (64bit): 2700MHz: 100F62/10000C7: 256KB: 2048KB

: 1024MB with 128MB shared memorySingle-Channel Memory Mode

: 1024MB/800MHz DDR3_1600: None

17

3.1.23.1.23.1.23.1.23.1.2 Navigation KeysNavigation KeysNavigation KeysNavigation KeysNavigation KeysPlease check the following table for the function description of each navigationkey.

Navigation Key(s) Function Description / Moves cursor left or right to select Screens / Moves cursor up or down to select items + / - To change option for the selected items To bring up the selected screen To display the General Help Screen To load optimal default values for all the settings To save changes and exit the BIOS SETUP UTILITY To jump to the Exit Screen or exit the current screen

3.23.23.23.23.2 Main ScreenMain ScreenMain ScreenMain ScreenMain ScreenWhen you enter the BIOS SETUP UTILITY, the Main screen will appear and displaythe system overview.

System Time [Hour:Minute:Second]Use this item to specify the system time.System Date [Day Month/Date/Year]Use this item to specify the system date.

3535353535

3 .33 .33 .33 .33 .3 OC TOC TOC TOC TOC Tweakweakweakweakweaker Screener Screener Screener Screener ScreenIn the OC Tweaker screen, you can set up overclocking features.

BIOS SETUP UTILITY

Main Advanced H/W Monitor Boot Security Exit

Overclocking may causedamage to your CPU andmotherboard.It should be done atyour own risk andexpense.


Enter Go to Sub ScreenF1 General HelpF9 Load DefaultsF10 Save and ExitESC Exit


OC Tweaker

EZ Overclocking

Load Optimized CPU OC Setting [Press Enter]

CPU Configuration

CPU Frequency (MHz)PCIE Frequency (MHz)

Overclock Mode[200][100]

[Auto]

Spread SpectrumBoot Failure Guard

Advanced Clock Calibration

CPU Active Core Control

Boot Failure Guard Count

AMD Turbo Core TechnologyAMD IO C-State Support

Processor Maximum FrequencyNorth BridgeProcessor Maximum Voltage

Maximum Frequencyx13.5 2700 MHZx10.0 201.325 V

00 MHz

[Auto][Enabled][3][Disabled]

[Disabled]

[Auto][Enabled]

Multiplier/Voltage Change [Auto]

Load Optimized mGPU OC Setting [Press Enter]

EZ OverclockingLoad Optimized CPU OC Setting

You can use this option to load the optiomized CPU overclocking setting.Please note that overclocking may cause damage to your CPU andmotherboard. It should be done at your own risk and expense.

3636363636

Load Optimized mGPU OC SettingYou can use this option to load mGPU overclocking setting. Please note thatoverclocing may cause damage to your mGPU and motherboard. It should bedone at your own risk and expense.

CPU ConfigurationOverclock Mode

Use this to select Overclock Mode. The default value is [Auto]. Configurationoptions: [Auto] and [Manual].

CPU Frequency (MHz) Use this option to adjust CPU frequency.

PCIE Frequency (MHz) Use this option to adjust PCIE frequency.

Spread SpectrumThis item should always be [Auto] for better system stability.

Boot Failure Guard Enable or disable the feature of Boot Failure Guard.

Boot Failure Guard Count Enable or disable the feature of Boot Failure Guard Count.

Advanced Clock CalibrationThis allows you to adjust Advanced Clock Calibration feature. The default valueis [Disabled]. Configuration options: [Disabled], [Auto], [All Cores] and [PerCore]. If you select [All Cores], you will see the option Value (All Cores).Configuration options: [+12%] to [-12%]. If you select [Per Core], you will seethe options Value (Core 0), Value (Core 1), Value (Core 2) and Value(Core 3). Configuration options: [+12%] to [-12%].

AMD Turbo Core TechnologyThis item appears only when the processor you adopt supports this feature.Use this to select enable or disable AMD Turbo Core Technology. Confi gurationoptions: [Auto] and [Disabled]. The default value is [Auto].

AMD IO C-State SupportThis allows you to enable or disable AMD IO C-State Support. The defaultvalue is [Enabled].

CPU Active Core ControlThis allows you to adjust CPU Active Core Control feature. The configurationoptions depend on the CPU core you adopt. The default value is [All Cores].

Processor Maximum FrequencyIt will display Processor Maximum Frequency for reference.

North Bridge Maximum FrequencyIt will display North Bridge Maximum Frequency for reference.

Processor Maximum VoltageIt will display Processor Maximum Voltage for reference.

3737373737

BIOS SETUP UTILITY

Main Advanced H/W Monitor Boot Security Exit

Overclocking may causedamage to your CPU andmotherboard.It should be done atyour own risk andexpense.




OC Tweaker

EZ Overclocking

Load Optimized CPU OC Setting [Press Enter]

CPU Configuration

CPU Frequency (MHz)PCIE Frequency (MHz)

Overclock Mode[200][100]

[Auto]

Spread SpectrumBoot Failure Guard

Advanced Clock Calibration

CPU Active Core Control

Boot Failure Guard Count

AMD Turbo Core TechnologyAMD IO C-State Support

Processor Maximum FrequencyNorth BridgeProcessor Maximum Voltage

Maximum Frequencyx13.5 2700 MHZx10.0 201.325 V

00 MHz

[Auto][Enabled][3][Disabled][Auto][Enabled][Disabled]

Multiplier/Voltage Change [Manual]

Load Optimized mGPU OC Setting [Press Enter]

CPU Frequency MultiplierFor safety and system stability, it is not recommended to adjust the value ofthis item.

Processor VoltageIt allows you to adjust the value of processor voltage. However, for safety andsystem stability, it is not recommended to adjust the value of this item.

NB Frequency MultiplierFor safety and system stability, it is not recommended to adjust the value ofthis item.

HT Bus SpeedThis feature allows you selecting Hyper-Transport bus speed. Configurationoptions: [Auto], [x1 200MHz] to [x8 1600MHz].

HT Bus WidthThis feature allows you selecting Hyper-Transport bus width. Configuraionoptions: [Auto], [8 Bit] and [16 Bit].

Memory ConfigurationMemory Clock

This item can be set by the code using [Auto]. You can set one of the standardvalues as listed: [400MHz DDR3_800], [533MHz DDR3_1066],[667MHz DDR3_1333] and [800MHz DDR3_1600].

DRAM VoltageUse this to select DRAM voltage. Configuration options: [Auto], [1.30V] to[2.05V]. The default value is [Auto].

Multiplier/Voltage ChangeThis item is set to [Auto] by default. If it is set to [Manual], you may adjust thevalue of Processor Frequency and Processor Voltage. However, it isrecommended to keep the default value for system stability.

3838383838

BIOS SETUP UTILITY

Memory Timing


+- Change OptionF1 General HelpF9 Load DefaultsF10 Save and ExitESC Exit


OC Tweaker



Bank InterleavingChannel Interleaving

[Auto][Hash 2]

Power Down Enable [Disabled]

CAS Latency (CL)TRCDTRPTRASCommand RateTRCTRTPTWRTRFCTRRDTWTRTRTPTFAW

[Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto][Auto]

Power Down EnableUse this item to enable or disable DDR power down mode.

Bank InterleavingInterleaving allows memory accesses to be spread out over banks on thesame node, or accross nodes, decreasing access contention.

Channel InterleavingIt allows you to enable Channel Memory Interleaving. Configuration options:[Disabled], [Address bits 6], [Address bits 12], [HASH 1] and [HASH 2]. Thedefault value is [HASH 2].

CAS Latency (CL)Use this item to adjust the means of memory accessing. The default value is[Auto].

TRCDUse this to adjust TRCD values. The default value is [Auto].

TRPUse this to adjust TRP values. The default value is [Auto].

TRASUse this to adjust TRAS values. The default value is [Auto].

Command RateUse this item to change Command Rate Auto/Manual setting. Min: 1N.Max: 2N. The default is [Auto].

TRCUse this to adjust TRC values. The default value is [Auto].

TRTPUse this to adjust TRTP values. The default value is [Auto].

TWRUse this to adjust TWR values. The default value is [Auto].

TRFCUse this to adjust TRFC values. The default value is [Auto].

Memory Timing

3939393939

TRRDUse this to adjust TRRD values. The default value is [Auto].

TWTRUse this to adjust TWTR values. The default value is [Auto].

TRTPUse this to adjust TRTP values. The default value is [Auto].

TFAWUse this to adjust TFAW values. The default value is [Auto].

Chipset SettingsOnboard GPU Clock Override

This allows you to enable or disable the Onboard GPU Clock Override feature.Onboard GPU Clock

This option only appears when you enable Onboard GPU ClockOverride. The default value is [500].

mGPU VoltageUse this to select mGPU voltage. Configuration options: [Auto], [1.10V] to[1.45V]. The default value is [Auto].

Would you like to save current setting user defaults?In this option, you are allowed to load and save three user defaults accordingto your own requirements.

4040404040

3.43.43.43.43.4 Advanced ScreenAdvanced ScreenAdvanced ScreenAdvanced ScreenAdvanced ScreenIn this section, you may set the configurations for the following items: CPUConfiguration, Chipset Configuration, ACPI Configuration, Storage Configuration, PCIPnPConfiguration, Floppy Configuration, SuperIO Configuration, and USB Configuration.

Setting wrong values in this section may causethe system to malfunction.

BIOS SETUP UTILITY

Main OC Tweaker H/W Monitor Boot Security Exit




Advanced

Advanced Settings

WARNING : Setting wrong values in below sectionsmay cause system to malfunction.

CPU Configuration

ACPI ConfigurationChipset Configuration

Storage ConfigurationPCIPnP ConfigurationFloppy ConfigurationSuperIO ConfigurationUSB Configuration

Options for CPU

BIOS Update Utility

Instant Flash

Instant FlashInstant Flash is a BIOS flash utility embedded in Flash ROM. This convenientBIOS update tool allows you to update system BIOS without entering operat-ing systems first like MS-DOS or Windows. Just launch this tool and savethe new BIOS file to your USB flash drive, floppy disk or hard drive, then youcan update your BIOS only in a few clicks without preparing an additionalfloppy diskette or other complicated flash utility. Please be noted that theUSB flash drive or hard drive must use FAT32/16/12 file system. If you ex-ecute Instant Flash utility, the utility will show the BIOS files and their respec-tive information. Select the proper BIOS file to update your BIOS, and rebootyour system after BIOS update process completes.

4141414141

3.4.13.4.13.4.13.4.13.4.1 CPU ConfigurationCPU ConfigurationCPU ConfigurationCPU ConfigurationCPU Configuration

BIOS SETUP UTILITY

CPU Configuration




Advanced



Cool' n' Quiet [Enabled]Secure Virtual MachineEnhanced Halt State(C1E)

[Enabled][Enabled]

Cool n QuietUse this item to enable or disable AMDs Cool n QuietTM technology. Thedefault value is [Enabled]. Configuration options: [Auto], [Enabled] and[Disabled]. If you install Windows 7 / VistaTM and want to enable thisfunction, please set this item to [Enabled]. Please note that enabling thisfunction may reduce CPU voltage and memory frequency, and lead to systemstability or compatibility issue with some memory modules or power supplies.Please set this item to [Disable] if above issue occurs.

Secure Virtual Machine When this option is set to [Enabled], a VMM (Virtual Machine Architecture)can utilize the additional hardware capabilities provided by AMD-V. Thedefault value is [Enabled]. Configuration options: [Enabled] and [Disabled].

Enhance Halt State (C1E)All processors support the Halt State (C1). The C1 state is supportedthrough the native processor instructions HLT and MWAIT and requires nohardware support from the chipset. In the C1 power state, the processormaintains the context of the system caches.

4242424242

BIOS SETUP UTILITY


Chipset Settings

Onboard HD AudioFront Panel

Onboard LanDr. LAN

Primary Graphics Adapter

Internal Graphics ModeShare Memory

[Disabled][Auto][Auto][Enabled]

[UMA][Auto][Disabled]

[PCI]


+ - Change OptionF1 General Help

F10 Save and ExitESC Exit

F9 Load Defaults

Advanced

PCIE2 Link ASPM [Disabled]

Link speed : 100 Mbps

Surround View

3.4.23.4.23.4.23.4.23.4.2 Chipset ConfigurationChipset ConfigurationChipset ConfigurationChipset ConfigurationChipset Configuration

PCIE2 Link ASPMThis allows you to adjust PCIE2 Link ASPM. Configuration options:[Disabled], [L0s], [L1] and [L0s & L1]. The default value is [Disabled].

Onboard HD AudioSelect [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. Ifyou select [Auto], the onboard HD Audio will be disabled when PCI SoundCard is plugged.

Front PanelSelect [Auto] or [Disabled] for the onboard HD Audio Front Panel.

Onboard LanThis allows you to enable or disable the onboard Lan feature.

Dr. LANThis allows you to select LAN Cable Detection function.

Primary Graphics AdapterThis item will switch the PCI Bus scanning order while searching for videocard. It allows you to select the type of Primary VGA in case of multiplevideo controllers. The default value of this feature is [PCI]. Configurationoptions: [PCI], [Onboard] and [PCI Express].

Internal Graphics ModeThis allows you to adjust internal graphics mode. The default value is[UMA]. Configuration options: [UMA] and [Disabled].

Share MemoryThis allows you to set share memory feature. The default value is [Auto].Configuration options: [Auto], [32MB], [64MB], [128MB], [256MB] and[512MB]. This option only appears when you set Internal Graphics Modeto [UMA].

Surround ViewThis allows you to enable or disable the Surround View feature.

4343434343

BIOS SETUP UTILITY

ACPI Settings Select auto-detect ordisable the STRfeature.




Advanced

Suspend To RAM

Check Ready BitAway Mode Support

Restore on AC / Power LossRing-In Power OnPCI Devices Power OnPS / 2 Keyboard Power OnRTC Alarm Power On

ACPI HPET Table

[Auto]

[Auto][Disabled]

[Power Off][Disabled][Disabled][Disabled][Disabled]

[Enabled]

3.4.33.4.33.4.33.4.33.4.3 ACPI ConfigurationACPI ConfigurationACPI ConfigurationACPI ConfigurationACPI Configuration

Suspend to RAMUse this item to select whether to auto-detect or disable the Suspend-to-RAM feature. Select [Auto] will enable this feature if the OS supports it.

Check Ready Bit Use this item to enable or disable the feature Check Ready Bit.

Away Mode SupportUse this item to enable or disable Away Mode support under Windows XPMedia Center OS. The default value is [Disabled].

Restore on AC/Power Loss This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.

Ring-In Power OnUse this item to enable or disable Ring-In signals to turn on the system fromthe power-soft-off mode.

PCI Devices Power OnUse this item to enable or disable PCI devices to turn on the system from thepower-soft-off mode.

PS/2 Keyboard Power OnUse this item to enable or disable PS/2 keyboard to turn on the system fromthe power-soft-off mode.

RTC Alarm Power OnUse this item to enable or disable RTC (Real Time Clock) to power on thesystem.

ACPI HPET TableUse this item to enable or disable ACPI HPET Table. The default value is[Disabled]. Please set this option to [Enabled] if you plan to use thismotherboard to submit Windows certification.

4444444444

BIOS SETUP UTILITY

Storage Configuration


Advanced

Onboard SATA Controller

SATA Operation Mode

IDE1 MasterIDE1 SlaveSATAII_1SATAII_2SATAII_3SATAII_4

[Enabled]

[IDE]

[Hard Disk][Not Detected][Not Detected][Not Detected][Not Detected][Not Detected]





Configure onboardserial ATAcontroller.

3.4.43.4.43.4.43.4.43.4.4 Storage ConfigurationStorage ConfigurationStorage ConfigurationStorage ConfigurationStorage Configuration

Onboard SATA ControllerUse this item to enable or disable the Onboard SATA Controller feature.

SATA Operation ModeUse this item to adjust SATA Operation Mode. The default value of thisoption is [IDE]. If you want to operate RAID function on SATA / SATAII HDDs,please select [RAID]. Configuration options: [AHCI], [RAID] and [IDE].

IDE Device ConfigurationYou may set the IDE configuration for the device that you specify. We willuse the IDE1 Master as the example in the following instruction, which canbe applied to the configurations of IDE1 Slave as well.

BIOS SETUP UTILITY

IDE Master Select the typeof device connectedto the system.




Advanced

Type

LBA/Large ModeBlock (Multi-Sector Transfer)PIO ModeDMA ModeS . M . A . R . T .32Bit Data Transfer

[Auto]

[Auto][Auto][Auto][Auto][Disabled][Disabled]

DeviceVendorSizeLBA ModeBlock ModePIO ModeAsync DMAUltra DMAS.M.A.R.T.

:Hard Disk:MAXTOR 6L080J4:80.0 GB:Supported:16Sectors:4:MultiWord DMA-2:Ultra DMA-6:Supported

4545454545

TYPEUse this item to configure the type of the IDE device that you specify.Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].[Not Installed]: Select [Not Installed] to disable the use of IDE device.[Auto]: Select [Auto] to automatically detect the hard disk drive.

After selecting the hard disk information into BIOS, use a diskutility, such as FDISK, to partition and format the new IDE harddisk drives. This is necessary so that you can write or read datafrom the hard disk. Make sure to set the partition of the PrimaryIDE hard disk drives to active.

[CD/DVD]:This is used for IDE CD/DVD drives.[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),

such as MO.LBA/Large Mode

Use this item to select the LBA/Large mode for a hard disk > 512 MB underDOS and Windows; for Netware and UNIX user, select [Disabled] todisable the LBA/Large mode.

Block (Multi-Sector Transfer)The default value of this item is [Auto]. If this feature is enabled, it willenhance hard disk performance by reading or writing more data duringeach transfer.

PIO ModeUse this item to set the PIO mode to enhance hard disk performance byoptimizing the hard disk timing.

DMA ModeDMA capability allows the improved transfer-speed and data-integrity forcompatible IDE devices.

S.M.A.R.T.Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,and Reporting Technology) feature. Configuration options: [Disabled], [Auto],[Enabled].

32Bit Data TransferUse this item to enable 32-bit access to maximize the IDE hard disk datatransfer rate.

4646464646

BIOS SETUP UTILITY

Advanced PCI / PnP Settings Value in units of PCIclocks for PCI devicelatency timerregister.




PCI Latency TimerPCI IDE BusMaster

[32][Enabled]

Advanced

3.4.53.4.53.4.53.4.53.4.5 PCIPnP ConfigurationPCIPnP ConfigurationPCIPnP ConfigurationPCIPnP ConfigurationPCIPnP Configuration

Setting wrong values in this section may causethe system to malfunction.

PCI Latency TimerThe default value is 32. It is recommended to keep the default value unlessthe installed PCI expansion cards specifications require other settings.

PCI IDE BusMasterUse this item to enable or disable the PCI IDE BusMaster feature.

4747474747

BIOS SETUP UTILITY

Floppy Configuration Select the type offloppy driveconnected to thesystem.




Advanced

Floppy A [1.44 MB 3 "]12

BIOS SETUP UTILITY

Configure Super IO Chipset Allow BIOS to Enableor Disable FloppyController.




Advanced

OnBoard Floppy ControllerSerial Port AddressParallel Port Address

Parallel Port ModeEPP VersionECP Mode DMA Channel

Parallel Port IRQ

[Enabled][3F8 / IRQ4][378][ECP + EPP][1.9][DMA3][IRQ7]

3.4.73.4.73.4.73.4.73.4.7 Super IO ConfigurationSuper IO ConfigurationSuper IO ConfigurationSuper IO ConfigurationSuper IO Configuration

OnBoard Floppy ControllerUse this item to enable or disable floppy drive controller.

Serial Port AddressUse this item to set the address for the onboard serial port or disable it.Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],[2E8 / IRQ3].

Parallel Port AddressUse this item to set the address for the onboard parallel port or disableit. Configuration options: [Disabled], [378], and [278].

3.4.63.4.63.4.63.4.63.4.6 Floppy ConfigurationFloppy ConfigurationFloppy ConfigurationFloppy ConfigurationFloppy ConfigurationIn this section, you may configure the type of your floppy drive.

4848484848

Parallel Port ModeUse this item to set the operation mode of the parallel port. The defaultvalue is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPPversion in the following item, EPP Version. Configuration options:[Normal], [Bi-Directional], and [ECP+EPP].EPP Version

Use this item to set the EPP version. Configuration options: [1.9]and [1.7].

ECP Mode DMA ChannelUse this item to set the ECP mode DMA channel. Configurationoptions: [DMA0], [DMA1], and [DMA3].

Parallel Port IRQUse this item to set the IRQ for the parallel port. Configuration options:[IRQ5] and [IRQ7].

4949494949

BIOS SETUP UTILITY

USB Configuration To enable or disablethe onboard USBcontrollers.




Advanced

USB Controller

USB 2.0 SupportLegacy USB Support

USB Keyboard/Remote Power OnUSB Mouse Power On

[Enabled]

[Enabled][Enabled]

[Disabled][Disabled]

3.4.83.4.83.4.83.4.83.4.8 USB ConfigurationUSB ConfigurationUSB ConfigurationUSB ConfigurationUSB Configuration

USB ControllerUse this item to enable or disable the use of USB controller.

USB 2.0 SupportUse this item to enable or disable the USB 2.0 support.

Legacy USB SupportUse this option to select legacy support for USB devices. There are fourconfiguration options: [Enabled], [Auto], [Disabled] and [BIOS SetupOnly]. The default value is [Enabled]. Please refer to below descriptionsfor the details of these four options:[Enabled] - Enables support for legacy USB.[Auto] - Enables legacy support if USB devices are connected.[Disabled] - USB devices are not allowed to use under legacy OS andBIOS setup when [Disabled] is selected. If you have USB compatibilityissue, it is recommended to select [Disabled] to enter OS.[BIOS Setup Only] - USB devices are allowed to use only under BIOSsetup and Windows / Linux OS.

USB Keyboard/Remote Power OnUse this item to enable or disable USB Keyboard/Remote Power On on thesystem.

USB Mouse Power OnUse this item to enable or disable USB Mouse Power On on the system.

5050505050

BIOS SETUP UTILITY

Hardware Health Event Monitoring


F1 General HelpF9 Load DefaultsF10 Save and ExitESC Exit


CPU TemperatureM / B Temperature

CPU Fan SpeedChassis Fan Speed

Vcore+ 3.30V+ 5.00V+ 12.00V

Power Fan Speed

: 37 C / 98 F

: 4722 RPM

: 1.216V: 3.248V: 5.136V: 12.091V

: 27 C / 80 F

: N / A: N / A

Main OC Tweaker Advanced Boot Security ExitH/W Monitor

Enable/DisableCPU Quiet FanFunction.

CPU Fan Setting

Chassis Fan 1 Setting

3.53.53.53.53.5 Hardware Health Event Monitoring ScreenHardware Health Event Monitoring ScreenHardware Health Event Monitoring ScreenHardware Health Event Monitoring ScreenHardware Health Event Monitoring ScreenIn this section, it allows you to monitor the status of the hardware on your system,including the parameters of the CPU temperature, motherboard temperature, CPU fanspeed, chassis fan speed, and the critical voltage.

CPU Fan SettingThis allows you to set the CPU fan speed. Configuration options: [Full On]and [Automatic mode]. The default is value [Full On].

Chassis Fan 1 SettingThis allows you to set the chassis fan 1 speed. Configuration options:[Full On] and [Manual Mode]. The default is value [Full On].

5151515151

BIOS SETUP UTILITY

Main OC Tweaker Advanced H/W Monitor Security Exit

Boot SettingsConfigure Settingsduring System Boot.




Boot

Boot Settings Configuration

1st Boot Device2nd Boot Device3rd Boot Device4th Boot Device

Hard Disk DrivesRemovable DrivesCD/DVD Drives

[1st Floppy Device][HDD: PM - HDS722580VL][CD / DVD: 3S - CD - ROM C][USB]

BIOS SETUP UTILITY

Boot Settings ConfigurationDisabled: Displaysnormal POST messages.Enabled: Displays OEMLogo instead of POSTmessages.


+ - Change OptionF1 General HelpF9 Load DefaultsF10 Save and ExitESC Exit


Boot

AddOn ROM DisplayBoot Logo

Boot From Onboard LANBootup Num-Lock

[Enabled][Auto][Disabled][On]

Full Screen Logo [Enabled]

3.63.63.63.63.6 Boot ScreenBoot ScreenBoot ScreenBoot ScreenBoot ScreenIn this section, it will display the available devices on your system for you to config-ure the boot settings and the boot priority.

3.6.13.6.13.6.13.6.13.6.1 Boot Settings ConfigurationBoot Settings ConfigurationBoot Settings ConfigurationBoot Settings ConfigurationBoot Settings Configuration

Full Screen Logo Use this item to enable or disable OEM Logo. The default value is [Enabled].AddOn ROM Display Use this option to adjust AddOn ROM Display. If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots, please select [Enabled]. Configuration options: [Enabled] and [Disabled]. The default value is [Enabled].

5252525252

BIOS SETUP UTILITY

Main OC Tweaker Advanced H/W Monitor Boot Exit

Install or Change thepassword.


Enter ChangeF1 General Help


F9 Load Defaults


Security

Change Supervisor Password

Change User Password

Security Settings

Supervisor Password : Not InstalledUser Password : Not Installed

Boot LogoUse this option to select logo in POST screen. This option only appearswhen you enable the option Full Screen Logo. Configuration options:[Auto], [EUP] and [Scenery]. The default value is [Auto].

Boot From Onboard LANUse this item to enable or disable the Boot From Onboard LAN feature.

Boot Up Num-LockIf this item is set to [On], it will automatically activate the Numeric Lockfunction after boot-up.

3.73 .73 .73 .73 .7 Security ScreenSecurity ScreenSecurity ScreenSecurity ScreenSecurity ScreenIn this section, you may set or change the supervisor/user password for the system.For the user password, you may also clear it.

5353535353

BIOS SETUP UTILITY

Main OC Tweaker Advanced H/W Monitor Boot Security

Exit system setupafter saving thechanges.

F10 key can be usedfor this operation.


Enter Go to Sub ScreenF1 General Help


F9 Load Defaults


Exit

Save Changes and Exit

Discard Changes and ExitDiscard Changes

Load BIOS DefaultsLoad Performance Setup DefaultLoad Power Saving Setup Default

Exit Options

3.83.83.83.83.8 Exit ScreenExit ScreenExit ScreenExit ScreenExit Screen

Save Changes and ExitWhen you select this option, it will pop-out the following message, Saveconfiguration changes and exit setup? Select [OK] to save the changesand exit the BIOS SETUP UTILITY.

Discard Changes and ExitWhen you select this option, it will pop-out the following message, Dis-card changes and exit setup? Select [OK] to exit the BIOS SETUP UTILITYwithout saving any changes.

Discard ChangesWhen you select this option, it will pop-out the following message, Dis-card changes? Select [OK] to discard all changes.

Load BIOS DefaultsLoad BIOS default values for all the setup questions. F9 key can be usedfor this operation.

Load Performance Setup DefaultThis performance setup default may not be compatible with all systemconfigurations. If system boot failure occurs after loading, please resumeoptimal default settings. F5 key can be used for this operation.

Load Power Saving Setup DefaultLoad power saving setup default. F6 key can be used for this operation.

5454545454

4.4.4.4.4. Software SupportSoftware SupportSoftware SupportSoftware SupportSoftware Support4.1 Install Operating System4.1 Install Operating System4.1 Install Operating System4.1 Install Operating System4.1 Install Operating SystemThis motherboard supports various Microsoft Windows operating systems: 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP Media Center / XP 64-bit. Becausemotherboard settings and hardware options vary, use the setup procedures in this chap-ter for general reference only. Refer to your OS documentation for more information.

4.2 Support CD Information4.2 Support CD Information4.2 Support CD Information4.2 Support CD Information4.2 Support CD InformationThe Support CD that came with the motherboard contains necessary drivers anduseful utilities that enhance the motherboard features.

4.2.1 Running The Support CD4.2.1 Running The Support CD4.2.1 Running The Support CD4.2.1 Running The Support CD4.2.1 Running The Support CDTo begin using the support CD, insert the CD into your CD-ROM drive. The CDautomatically displays the Main Menu if AUTORUN is enabled in your c

dl-960gm-gs3 tricks

Documents

copyright notice

2013copyright2013 digilite

written consent of digilite

loss of business

loss ofprofits

loss of data

consequential damages

harmful interference