detail booklet stotherm ci · 2020. 9. 14. · stotherm® ci termination at grade - sheathing flush...
TRANSCRIPT
Detail Booklet StoTherm® ciSeries 52s.xxSteel Frame Construction December 2018
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, of for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.comProperty of Sto Corp.All Rights Reserved.
3800 Camp Creek Pkwy. SWBldg. 1400 • Suite 120Atlanta, GA 30331Tel: (800) 221-2397Fax: (404) 346-3119helpdesk.stocorp.com
Sto Corp.
StoTherm® ciSystem Components
Detail No.: 52s.00 Date: December 2018
Notes:
1. StoTherm ci SystemComponents:
- StoGuard Air andMoisture Barrier
- Sto Adhesive- Sto EPS Insulation Board- Sto Mesh- Sto Primer (optional)- Sto Base Coat- Sto Finish
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
®
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Sheathing
Sto EPS Insulation Board
Sto MeshSto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Adhesive
StoTherm® ciSystem Components: Ultra-High Impact Resistance
Detail No.: 52s.01 Date: December 2018
®
Notes:
1.StoTherm ci SystemComponents:- StoGuard air and Moisture
Barrier- Sto Adhesive- Sto EPS Insulation Board- Sto Armor Mat XX- Sto Mesh- Sto Primer (optional)- Sto Base Coat- Sto Finish
2. Ultra-high impactresistance recommended atall ground floors to aminimum height of 6'-0"(1.8 m) above finished gradeand other areas accessible topedestrian traffic, abnormalstress or impact.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
Sto Materials:
1.Sample Text
1.Sample Notes
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
(with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Adhesive
Sheathing
Sto EPS Insulation Board
Sto MeshSto Base Coat
Sto Base Coat (with Sto Armor Mat Embedded)
®
Notes:
1.StoTherm ci Components:- StoGuard Air and Moisture
Barrier- Sto Adhesive- Sto EPS ProD or Sto GPS
ProD Insulation Board- Sto Base Coat embedded
with Sto Mesh- Sto Armat Classic Plus
Fortification Layer embeddedwith Sto Mesh- Sto Finish
2. Sto Armat Classic PlusFortification Layer improves theimpact resistance of the entirecladding assembly from bluntimpact and from repetitive andconcentrated impacts (e.g. birdstrikes)
- Refer to StoTherm ci SystemBulletins and Specifications, StoProduct Bulletins, Tech Hotlines,and Sto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified as Stoare furnished by othermanufacturers and are notnecessarily installed by trades whoinstall the Sto products. Refer toproject specific contract documents.
Sto Materials:
1.Sample Text
1.Sample Notes
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoTherm® ci with Sto IMPACTSystem Components
Detail No.: 52s.02 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Sto Armat Classic Plus Fortification Layer with Sto Mesh(See Note #2)
Sto Finish
Sto Adhesive
Sheathing
Sto EPS ProD or Sto GPS ProD Insulation Board
Sto Base Coat with Sto Mesh (embedded)
StoTherm® ciTermination at Grade - Sheathing Flush with Foundation or Slab Edge
Detail No.: 52s.03A Date: December 2018
®
Notes:
1. Terminate systemminimum 6" (15.2 cm)above finished grade, higherfor areas with heavy snowaccumulations, or whererequired by code.
2. Ultra-high impactresistance recommended atall ground floors to aminimum height of 6'-0"(1.8 m) above finished gradeand other areas accessible topedestrian traffic, abnormalstress or impact.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Sto AdhesiveSheathing
Sto EPSInsulation Board, Pre- Wrapped
Sto Mesh
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (Protect with StoCoat Acryl Plus or Flashing)
StoGuard® Air and Moisture Barrier Detail ComponentFlashing, Sloped
Backer Rod & Sealant w/ Weep Holes
Terminate Assembly 6" (152 mm) Above Grade, min.
StoTherm® ciTermination at Grade - Sheathing Overlapping Slab or Foundation
Detail No.: 52s.03B Date: December 2018
®
Notes:
1. Terminate systemminimum 6" (15.2 cm)above finished grade, higherfor areas with heavy snowaccumulations, or whererequired by code.
2. Ultra-high impactresistance recommended atall ground floors to aminimum height of 6'-0"(1.8 m) above finished gradeand other areas accessible topedestrian traffic, abnormalstress or impact.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Sto AdhesiveSheathing
Sto EPSInsulation Board, Pre-Wrapped
Terminate Assembly 6" (152 mm) Above Grade, min.
Sto Mesh
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (Protect with StoCoat Acryl Plus or Flashing)
StoGuard® Air and Moisture Barrier Detail Component
Flashing, Sloped
Backer Rod & Sealant w/ Weep Holes
StoTherm® ciAesthetic Feature Band
Detail No.: 52s.04Date: December 2018
®
Notes:
1. Feature band attachedwith Sto TurboStickAdhesive, also used as fillerand rasped smooth at anygaps between feature bandand base layer of insulationboard.
2. Slope top surface offeature band minimum 27degrees. Increase slope fornorthern climates to preventsnow and ice accuulations.
3. Limit thickness of build-out to reduce maintenanceassociated with projectingarchitectural features.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sheathing
Sto EPSInsulation Board
Sto Base Coat (with Sto Mesh Embedded)
StoGuard® Air and Moisture Barrier
Sheathing
Sto EPSInsulation Board
(with Sto Mesh Embedded) Sto Base Coat
Sto Flexyl (with Sto Mesh or Sto Detail Mesh Embedded); Return Vertically 4" (102 mm) min. Above and Below Feature Band
Sto Mesh
Sto Mesh
Sto Finish
Sto Finish
Sto Primer (Required over Sto Flexyl and Sto Base Coat Above and Below)
Sto Adhesive
Sto Adhesive
Thin Build-Out
Thick Build-Out
Thick Build-Out, 2-4 in. (51-102 mm)
Thin Build-Out,
≤ 2 in. (51 mm)
StoTherm® ciAesthetic Reveal
Detail No.: 52s.05 Date: December 2018
®
Notes:
1. Slope bottom surface ofreveal minimum 27 degrees.Increase slope for northernclimates to prevent snowand ice accumulations.
2. Maintain minimum 3/4inch (19 mm) thickness ofinsulation board at base ofreveal.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto Primer (Optional)
Sto Finish
Sto Adhesive
Sto EPSInsulation Board
Sto Base Coat (with Sto Detail Mesh Embedded)
3/4" (19 mm) min.
2 1/2" (64 mm) min. Ovelap of Sto Detail Mesh w/ Sto Mesh @ Top and Bottom of Reveal
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Detail Mesh
Sto Primer (Optional)
Sto Finish
Sto Adhesive
Sto EPSInsulation Board
3/4" (19 mm) min.
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sheathing
Sheathing
Option 1 with Sto Detail Mesh
Option 2 with Continuous Sto Mesh
StoTherm® ciReceptor-Type Window Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23A-1 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection Over Blocking
Blocking
StoGuard® Air and Moisture Barrier Rough Opening Protection
Step 1 - Rough Opening Protection
StoTherm® ciReceptor-Type Window Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23A-2 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
End Dam Set in Sealant
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped
Sto TurboStick Adhesive (Fill Gap Between EPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth)
Sto EPS Insulation Board, Pre-Wrapped around Rough Opening
Sill Receptor w/ Weep Holes (Sill Flashing Extender Not Shown for Clarity)
Sto Adhesive
Weep Holes
Angle (As Needed for Attachment of Sill Receptor and Support)
StoGuard® Air and Moisture Barrier Rough Opening Protection
Blocking
Step 2 - Receptor with End Dam
StoTherm® ciReceptor-Type Window Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23A-3 Date: December 2018
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
Backer Rod & Sealant (Entire Perimeter)
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped at Jamb
Sto EPS Insulation Board, Pre-Wrapped around Rough Opening
Sill Receptor w/ Weep Holes
Sto Adhesive
Spray Polyurethane Foam Insulation
Jamb Receptor
Sill Extender w/ Continuous Bead of Sealant @ Bottom
Window Assembly
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
Angle (As Needed for Attachment of Sill Receptor and Support)
StoGuard® Air and Moisture Barrier Rough Opening Protection
Blocking
Step 3 - Window and Sill Flashing, Cladding, and Perimeter Weather and Air Seals
StoTherm® ciReceptor-Type Window Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23B-1 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Cement Board Filler or Other TrimFlashing
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier Detail Component
Step 1 - Rough Opening Protection, Head Flashing
StoTherm® ciReceptor-Type Window Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23B-2 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped
Sto TurboStick Adhesive (Fill Gap Between EPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth, Reinforce Top Corner with Sto Mesh or Sto Detail Mesh Embedded in Base Coat)
Sto EPS Corner Board, Pre-Wrapped around Rough Opening
Window Assembly
Spray Polyurethane Foam Insulation
Head Receptor
Jamb Receptor
Cement Board Filler or Other TrimFlashing
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
Sto Adhesive
Step 2 - Receptor and Window
StoTherm® ciReceptor-Type Window Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.23B-3 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-WrappedSto TurboStick Adhesive (Fill Gap Between EPS Boards at Corner with this Adhesive, Cut Flush with Surface and Rasp Smooth)
Sto EPS Corner Board, Pre-Wrapped around Rough Opening
Window Assembly
Sto Adhesive
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
Air Seal, Backer Rod and Sealant (Air Seal Entire Perimeter)
Head Receptor
Jamb Receptor Backer Rod & Sealant (Entire Perimeter, with Weeps at Head)
Cement Board Filler or Other Trim (Finish Cement Bd. w/ StoCoat Acryl Plus)
Flashing
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Air and Moisture Barrier
Spray Polyurethane Foam Insulation
Step 3 - Cladding and Perimeter Weather and Air Seals
StoTherm® ciFlanged Window-Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24A-1 Date: December 2018
Property of Sto Corp. All Rights Reserved.
Step 1 - Rough Opening Protection, Sill Flashing
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
1/8" (3 mm) Thick Washers Behind Mounting Flange
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Flashing
Slope
StoTherm® ciFlanged Window-Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24A-2 Date: December 2018
Property of Sto Corp. All Rights Reserved.
Step 2 - Window and Trim
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped Around Opening (Cut Kerf in Back of Insulation and Slide over End Dam. Position insulation over Flashing with 1/4" [6 mm] Gap for Drainage)
Spray Polyurethane Foam Insulation
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sealant Behind Mounting Flange (Jambs and Head Only)
Sto Adhesive
StoGuard® Detail Component
Flashing
Slope
Window Assembly
1/8" (3 mm) Thick Washers Behind Mounting Flange
Spray Polyurethane Foam Insulation
StoTherm® ciFlanged Window-Sill
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24A-3 Date: December 2018
Step 3 - Cladding and Perimeter Weather and Air Seals
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
Backer Rod & Sealant (Entire Perimeter)
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped Around Opening
Sto EPS Insulation Board
Spray Polyurethane Foam Insulation
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto Adhesive
StoGuard® Detail ComponentFillet Bead of Sealant (not
shown) Between Underside of Flashing and Base Coat
1/8" (3 mm) Thick Washers Behind Mounting Flange
Sealant Behind Mounting Flange (Jambs and Head Only)
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
Spray Polyurethane Foam Insulation
Backer Rod & Sealant with Weeps Between Trim and Flashing Leg
Flashing
Air Seal, Backer Rod & Sealant (Air Seal Entire Perimeter)
StoTherm® ciFlanged Window-Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24B-1 Date: December 2018
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Flashing
Sealant Behind Mounting Flange (Jambs and Head Only)
Sealant
Property of Sto Corp. All Rights Reserved.
Step 1 - Rough Opening Protection, Head Flashing
StoTherm® ciFlanged Window-Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24B-2 Date: December 2018
Property of Sto Corp. All Rights Reserved.
Step 2 - Window and Trim
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped Around Opening
Sto EPS Insulation Board
Window Assembly
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto Adhesive
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Sealant
Spray Polyurethane Foam Insulation
Flashing
Backer Rod & Sealant Weather and Air Seals (Entire Perimeter with Weeps Between Underside of Trim & Flashing Leg)
Spray Polyurethane Foam Insulation
StoTherm® ciFlanged Window-Head
®
Notes:
1. Consult with window andsealant manufacturers toverify window installation anddetailing and to assure nowater leakage into the wallassembly. Consult withwindow manufacturerregarding window and/orflashing assembly thermalbreaks to avoid condensation.Test the final assembly usingmaterials and tradesassociated with the project toverify performance. Correctany deficiencies associatedwith excess air leakage,water infiltration into the wallassembly, or structuralinadequacies.
2. Construct a site built mock-up using materials and sub-trades associated with theproject to verify installationsequencing, detailing, andaesthetics.
- Refer to StoTherm ci SystemBulletins and Specifications,Sto Product Bulletins, TechHotlines, and Sto Installationand Maintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.24B-3 Date: December 2018
Step 3 - Cladding and Perimeter Weather and Air Seals
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded)
Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto EPS Insulation Board, Pre-Wrapped Around Opening
Sto EPS Insulation Board
StoGuard® Air and Moisture Barrier Rough Opening Protection
Sto Adhesive
StoGuard® Detail Component
Sealant Behind Mounting Flange (Jambs and Head Only)
Sealant
Spray Polyurethane Foam Insulation
Flashing
Spray Polyurethane Foam Insulation
Window Assembly
Backer Rod & Sealant Weather and Air Seals (Entire Perimeter with Weeps Between Underside of Trim & Flashing Leg)
StoTherm® ciSoffit: Insulated and Unvented
Detail No.: 52s.30 Date: December 2018
®
Notes:
1. Continue StoGuard air andmoisture barrier onto dissimilarmaterial or construction whererequired after verifying substratematerial compatibility. Refer toSto Detail 52s.53 for typicaldetailing of inside corner ifsubstrate material orconstruction is dissimilar. Referto Sto Detail 52s.54A ifsubstrate material is similar atinside corner.
2. 4" (10 cm) thick insulationboard typically required forproper lap of accessory withmesh "tail." For thinnersections of insulation board pre-wrap insulation board with Stobase coat and mesh.
3. Multi-story buildings whereconstruction is required to beNoncombustible may requirespecial examination of soffitconditions with foam plasticinsulation. Verify withprofessional fire protectionengineer and building codeofficial.
- Refer to StoTherm ci SystemBulletins and Specifications, StoProduct Bulletins, Tech Hotlines,and Sto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Nominal 1/4 inch (6 mm) Gap for Drainage
Sheathing
Sto EPS Insulation Board, Pre-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive
StoGuard® Joint Treatment
Backer Rod and Sealant
Structure
Sto Drip Edge Profile
Sto Drip Edge Profile (See Drawing Below) Dissimilar Material or
Wall Construction
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
StoTherm® ciSoffit: Uninsulated and Vented
Detail No.: 52s.31 Date: December 2018
®
Notes:
1. Prevent "communication"of vented air space withconditioned interior air toreduce the likelihood ofcondensation on materials inthe vented space.
3. Typical soffit board isgypsum sheathing incompliance with ASTM C1177. Refer to StoSpecification No. F601S andSto Detail Series 14.xx.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Nominal 1/4 inch (6 mm) Gap for Drainage
Sheathing
Sto EPS Insulation Board, Pre-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive
Backer Rod and Sealant
Structure
Sto Drip Edge Profile
Sto Drip Edge Profile (See Drawing Below) Dissimilar Material or
Wall Construction
Light Gauge Steel Stud FramingStoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
StoGuard® Joint Treatment
Soffit Vent
Casing Bead
StoTherm® ciFloor Line Without Deflection
Detail No.: 52s.40 Date: December 2018
®
Notes:
1. This detail is typicallylimited to low-riseconstruction where no floorline deflection is anticipated.Refer to Sto Detail 52s.41A,B, or C for a floor linecondition with deflection.
2. Sheathing attachment istypically at 8" (20.3 cm) oncenter or less vertically. AddC-channels or otherattachment means alongslab edge if necessary toconform with requiredfastener spacing.
3. Provide fire stopping atfloor line as needed.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
Sto EPS Insulation Board
Sto Base Coat (with Sto Mesh Embedded)
Sto Adhesive
Sto Mesh
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Structure
StoTherm® ciFloor Line With Deflection -Concealed Flashing and Drainage at Floor Line
Detail No.: 52s.41A Date: December 2018
Notes:
1. Sheathing attachment istypically at 8" (20.3 cm) oncenter or less vertically. AddC-channels or otherattachment means alongslab edge if necessary toconform with requiredfastener spacing.
2. Provide fire stopping atfloor line as needed.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICCReports for building codecompliance information.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
Cant Bead of Sto RapidGuard
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
®
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
Sto EPS Insulation Board, Pre-Wrapped @ Top and Bottom to Allow for Drainage
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
StoGuard® Transition Membrane
Horizontal Deflection Joint: Backer Rod & Sealant w/ Weeps. Sealant Applied to Base Coat as per Sealant Manufacturer Instructions
Slotted Deflection Track
Backer Rod
Structure
StoTherm® ciFloor Line With Deflection - No Drainage at Floor Line
Detail No.: 52s.41B Date: December 2018
®
Notes:
1. Sheathing attachment istypically at 8" (20.3 cm) oncenter or less vertically. AddC-channels or otherattachment means alongslab edge if necessary toconform with requiredfastener spacing.
2. Provide fire stopping atfloor line as needed.
3. Provide drainage at floorlines as deemed by DesignProfessional, typically nomore than every third floorline. Refer to Sto Detail52s.41A.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
Sto EPS Insulation Board, Pre-Wrapped @ Top and Bottom to Allow for Drainage
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
StoGuard® Transition Membrane
Horizontal Deflection Joint: Backer Rod & Sealant. Sealant Applied to Base Coat as per Sealant Manuf'r Instructions
Slotted Deflection Track
Backer Rod
Structure
StoTherm® ciFloor Line With Deflection -Flashing and Drainage at Floor Line
Detail No.: 52s.41C Date: December 2018
Notes:
1. Sheathing attachment istypically at 8" (20.3 cm) oncenter or less vertically. AddC-channels or otherattachment means alongslab edge if necessary toconform with requiredfastener spacing.
2. Provide fire stopping atfloor line as needed.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICCreports for building codecompliance information.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
®
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sheathing
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
StoGuard® Transition Membrane
Sto EPS Insulation Board, Pre-Wrapped @ Top and Bottom to Allow for Drainage
Slotted Deflection Track
Backer Rod
Structure
Flashing
Sealant
Horizontal Deflection Joint: Backer Rod & Sealant w/ Weeps. Sealant Applied to Base Coat as per Sealant Manufacturer Instructions
StoGuard® Air and Moisture Transition Component
®
Notes:
1. Detail apples to BalconyProtected Overhead byBalcony Ceiling Above.
2. Slope balcony to directwater away from wall.
3. Consider the use of highor ultra-high reinforcingmeshes on balcony walls tosupplement standardreinforcing mesh for addedabuse and impact resistance.
4. Verify compatibility ofStoGuard Air and MoistureBarrier with balconywaterproof membranematerial where they interfaceor lap one another.
5. Counter flash balconymembrane on wall if notfluid applied.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.42A Date: December 2018
StoTherm® ciBalcony Floor/Wall
Sto Primer (Optional)
Sto Finish
Sto Mesh
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
Sto EPS Insulation Board, Pre-Wrapped
Sto Adhesive
Balcony Slab Recess
Backer Rod & Sealant w/ Weeps
Balcony Waterproof Membrane and Finished Flooring
Balcony
Cant and Air Seal Transition Material
®
Notes:
1. Detail applies to BalconyProtected by Balcony CeilingAbove.
2. Underside of balcony mayalso be finished with StoFinish or other Sto smooth ortextured coatings.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.42B Date: December 2018
StoTherm® ciBalcony Ceiling/Wall
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Sto Adhesive
(with Sto Mesh Embedded) Sto Base Coat
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Sheathing
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
Sto Mesh
Backer Rod
Backer Rod and Sealant
Balcony
Slotted Deflection Track
Skim Coat of Sto Base Coat
Sto Primer Smooth
StoCoat Acryl Plus
StoTherm® ciHorizontal Termination at Dissimilar Cladding
Detail No.: 52s.50 Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board, Back-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Backer Rod and Sealant with Weep Holes
Sheathing
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
Sealant
StoGuard® Air and Moisture Barrier Detail Component
Wood Blocking
Brick Cavity Wall
Masonry Sill
Flashing
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
StoTherm® ciVertical Termination at Dissimilar Cladding
Detail No.: 52s.51A Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sheathing
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto AdhesiveLight Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sto Finish
Masonry Veneer or Other Dissimilar Material
Sealant and Backer Rod
StoTherm® ciVertical Termination at Dissimilar Backup Wall Construction
Detail No.: 52s.51B Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier Sheathing
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier (Minimum Two Coats on CMU Wall Surface)
CMU Backup
Masonry Veneer or Other Dissimilar Material
Sto Finish
Sealant and Backer Rod
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Primer (Optional)
Sto Adhesive
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
StoTherm® ciVertical Expansion Joint in Back-Up Wall
Detail No.: 52s.52A Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sheathing
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto AdhesiveLight Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
Sto Primer (Optional)
Sealant and Backer Rod
Sto Finish
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
StoTherm® ciVertical Expansion Joint in Back-Up Wall,StoTherm ci and Dissimilar Cladding
Detail No.: 52s.52B Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
Masonry Veneer or Other Dissimilar Material
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
SheathingSto Primer (Optional)
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Finish
Sealant and Backer Rod
Light Gauge Steel Stud Framing
StoTherm® ciInside Corner with Dissimilar Backup Wall
Detail No.: 52s.53 Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board, Back-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Mesh
Sto Adhesive
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture BarrierLight Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
Sealant and Backer Rod
StoGuard® Air and Moisture Barrier (Minimum Two Coats on CMU Wall Surface)
CMU Backup
Sheathing
StoTherm® ciInside and Outside Corner with Common Substrateand StoMesh Corner Bead Reinforcement
Detail No.: 52s.54A Date: December 2018
®
Notes:
1. Provide joint at interiorcorner if movement isanticipated. Refer to StoDetail 52s.53.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board
Sto Base Coat (with Sto Mesh Embedded)
Sto Adhesive StoGuard® Joint Treatment
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier
Sheathing
Sto-Mesh Corner Bead Standard (Embedded in Sto Base Coat)
Sto Mesh, (Overlap StoMesh Corner Bead 4 in. ea. Side, min.)
Return Sto Mesh 6 in. min. @ Inside Corner
StoTherm® ciInside and Outside Corner with Common Substrateand Sto Mesh Reinforcement
Detail No.: 52s.54B Date: December 2018
®
Notes:
1. Provide joint at interiorcorner if movement isanticipated. Refer to StoDetail 52s.53.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board
Sto Base Coat (with Sto Mesh Embedded)
Sto Adhesive StoGuard® Joint Treatment
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier
Sheathing
Return Sto Mesh 6 in. min. Around Corner
Return Sto Mesh 6 in. min. @ Inside Corner
Sto Mesh
StoTherm® ciTermination at Parapet - Front
Detail No.: 52s.60A Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board, Back-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Adhesive
Metal Coping
Light Gauge Steel Stud Framing
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier
Sheathing
Roof Structure
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Wood Blocking
StoGuard® Detail Component
Sto Mesh
Backer Rod & Sealant
StoTherm® ciTermination at Parapet - Back
Detail No.: 52s.60B Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sto EPS Insulation Board, Pre-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Adhesive
Metal Coping
Roof Membrane
Sto Primer (Optional)
Sto Finish
StoGuard® Air and Moisture Barrier Detail Component
Sheathing
Roof Structure
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Wood Blocking
Backer Rod and Sealant
Sto Mesh
StoGuard® Detail Component
Termination Bar for Roof Membrane
Light Ga. Steel Stud Framing
Cover BoardRoof Insulation
StoGuard® Air and Moisture Barrier
Termination Bar for Roof Membrane
Sto EPS Insulation Board, Pre-Wrapped
Wood Blocking
StoGuard® Detail Component
Insulation
Z-Flashing
Roof Membrane
StoGuard® Air and Moisture Barrier
Sheathing
Backer Rod and Sealant with Weep Holes
StoTherm® ciParapet with Cornice Feature
Detail No.: 52s.61 Date: December 2018
®
Notes:
1. Cornice feature limited to 12"(30.5 cm) maximum thicknessfor noncombustible typeconstruction. Special analysiswith regard to fire propagationmay enable thicker sections.Thicker sections permittedwithin practical limits forcombustible construction.
2. Cornice feature attached withSto TurboStick Adhesive; alsoused as filler and rasped smoothat any gaps between featureband and base layer ofinsulation board.
3. Cornice feature may also beattached directly to StoGuardwhere applicable.
4. Supplemental mechanicalattachment of feature bandmaybe necessary in some cases.Verify installation method foradequate attachment beforecommencing work.
- Refer to StoTherm ci SystemBulletins and Specifications, StoProduct Bulletins, Tech Hotlines,and Sto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
View of Pre-Wrapped CorniceView of Mesh Overlap
Sto Mesh Embedded in Base Coat Laps Sto Mesh on Cornice 2 1/2 in. (64 mm) min.
Sto EPS Insulation Cornice Feature
Cornice Feature Pre-Wrapped with Sto Base Coat (with Sto Mesh Embedded)
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
Wood Construction as Required StoGuard® Air and Moisture Barrier Sheathing Joint Treatment Extends 2 in. (51 mm) min. at Vertical and Horizontal Surfaces
Sto EPS Insulation Board, Back-Wrapped or Pre-Wrapped at Termination
Sto Base Coat (with Sto Mesh Embedded)
Metal Coping
Sto Primer (Optional)
Sto Finish
Sheathing
Backer Rod and Sealant
Sto Mesh
Light Gauge Steel Stud Framing
StoGuard® Air and Moisture Barrier
1/2 in. (13 mm) min. Gap Between Top Surface of Cornice Feature and Underside of Wood ConstructionPre-Wrapped
Cornice
StoTherm® ciDiverter Flashing at Roof/Wall Abutment
Detail No.: 52s.62 Date: December 2018
®
Notes:
1. Maintain minimum 2" (51mm) gap between roofshingles and StoTherm citermination. Increase gapfor low slope roofs toprevent snow and iceaccumulations.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Backer Rod and Sealant Around Vertical Leg of Diverter Flashing
Diverter Flashing
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier Detail Component
Sto EPS Insulation Board, Pre-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sheathing
Sto Mesh
Light Gauge Steel Stud Framing
Drip Edge Flashing
Gutter
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Sto AdhesiveDiverter Flashing
Terminate StoTherm ci 2 in. (51 mm) Above Finished Roof
Fascia
Drip Edge Flashing
Roof Structure
Step Flashing
Step Flashing
Sto Finish
Roof ShinglesRoof Underlayment
StoTherm® ciGravel Stop
Detail No.: 52s.63 Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board, Back-Wrapped
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Roof Air Barrier
Sto Mesh
Light Gauge Steel Stud Framing
Sto Adhesive
Gravel Roof Ballast
Continuous Cleat
Gravel Stop
Sheathing
1/4" (6 mm) Min. Gap Between Top of EPS Insulation Board and Wood Blocking
Wood Blocking
Roof Membrane
Roof Insulation
Roof Sheathing
Roof Structure
StoGuard® Air and Moisture Barrier Sheathing Joint Treatment
Backer Rod & Sealant
StoTherm® ciSaddle Flashing at Lower/Higher Wall Abutment
®
Notes:
1. Provide minimum 2" (51mm) gap between parapetcap flashing and StoThermci termination.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Sheathing
Detail No.: 52s.64-1 Date: December 2018
StoGuard® Detail Component
StoGuard® Air and Moisture Barrier
Light Gauge Steel Stud Framing
Step 1 - Air and Moisture Barrier
StoTherm® ciSaddle Flashing at Lower/Higher Wall Abutment
®
Notes:
1. Provide minimum 2" (51mm) gap between parapetcap flashing and StoThermci termination.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved. Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.64-2 Date: December 2018
A
BC
StoGuard® Air and Moisture Barrier
StoGuard® Air and Moisture Barrier
Assembled Saddle Flashing
Saddle Flashing Components
Step 2 - Saddle Flashing
StoTherm® ciSaddle Flashing at Lower/Higher Wall Abutment
®
Notes:
1. Provide minimum 2" (51mm) gap between parapetcap flashing and StoThermci termination.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved. Property of Sto Corp. All Rights Reserved.
Detail No.: 52s.64-3 Date: December 2018
Parapet Cap Flashing Assembly Extends to Perpendicular Wall
Light Gauge Steel Stud Framing
StoGuard® Transition Membrane Embedded in StoGuard® Air and Moisture Barrier (or Compatible Roofing Membrane)
StoGuard® Detail Component
Wood Blocking
Saddle Flashing Assembly
Backer Rod & Sealant Between StoTherm ci and Saddle Flashing Assembly
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board, Pre-Wrapped at Termination
StoTherm ci Assembly
Step 3 - Cladding, Coping, and Sealant
StoTherm® ciScupper Penetration
Detail No.: 52s.65 Date: December 2018
®
Notes:
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board, Back-Wrapped Around Scupper Penetration
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sto Adhesive
Sheathing
Wood Blocking
Roof Membrane
Roof Insulation
Roof Structure
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Scupper Assembly
®
Notes:
1. Refer to Sto Detail52s.70B where sheathing is"rough cut" around pipe orwhere gap around pipeexceeds allowable gapdimension for StoGuard Airand Moisture Barrier DetailComponent.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board, Back-Wrapped Around Pipe Penetration
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sto Adhesive
Sheathing
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Pipe
Detail No.: 52s.70A Date: December 2018
StoTherm® ciPipe Penetration - Precision Cut Sheathing
®
Notes:
1. Appropriate spray foam isused to fill gaps insheathing. Where sheathingfits snug around pipe refer toSto Detail 52s.70A.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
Retrofit or Oversized Pipe Penetration Opening
Detail No.: 52s.70B Date: December 2018
StoTherm® ciPipe Penetration - Rough Cut Sheathing
StoGuard® Air and Moisture Barrier
Sto EPS Insulation Board, Back-Wrapped Around Pipe Penetration Sto Base Coat (with
Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sto Adhesive
Sheathing
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component
Pipe
Spray Foam (to Fill Gaps, Shaved or Rasped Flush with Sheathing Surface)
StoTherm® ciSign Attachment
Detail No.: 52s.71 Date: Date: December 2018
®
Notes:
1. Blocking not requiredwhere solid substrate orwood-based sheathing iscapable of supporting thesign (or other attachedobject). Use appropriatefasteners for attachment.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sheathing
Wood Blocking
Hole Drilled in EIFS and Lined with Sealant
PVC or Stainless Steel Sleeve (Sleeve Extends From Finish Through Blocking, Shown Partial Length for Clarity)
Neutral Cure Sealant
Sign
Washer Behind Sign Set in Sealant
Sto EPS Insulation Board
Sto Adhesive
Bolt w/ Washers at Each End
StoTherm® ciFixture Attachment
Detail No.: 52s.73 Date: December 2018
®
Notes:
1. Attach fixture to blockingor solid substrate. Whereattached to blocking seal theblocking with Sto DetailComponent.
- Refer to StoTherm ciSystem Bulletins andSpecifications, Sto ProductBulletins, Tech Hotlines, andSto Installation andMaintenance Guides forcomplete information.
- Refer to applicable ICC orCCMC Evaluation Reports forbuilding code complianceinformation.
- Components not identified asSto are furnished by othermanufacturers and are notnecessarily installed by tradeswho install the Sto products.Refer to project specific contractdocuments.
ATTENTION
Sto products are intended for use by qualified professional contractors, not consumers, as a component of a larger construction assembly as specified by a qualified design professional, general contractor or builder. They should be installed in accordance with those specifications and Sto’s instructions. Sto Corp. disclaims all, and assumes no, liability for on-site inspections, for its products applied improperly, or by unqualified persons or entities, or as part of an improperly designed or constructed building, for the nonperformance of adjacent building components or assemblies, or for other construction activities beyond Sto’s control. Improper use of Sto products or use as part of an improperly designed or constructed larger assembly or building may result in serious damage to Sto products, and to the structure of the building or its components.
STO CORP. DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED EXCEPT FOR EXPLICIT LIMITED WRITTEN WARRANTIES ISSUED TO AND ACCEPTED BY BUILDING OWNERS IN ACCORDANCE WITH STO’S WARRANTY PROGRAMS WHICH ARE SUBJECT TO CHANGE FROM TIME TO TIME. For the fullest, most current information on proper application, clean-up, mixing and other specifications and warranties, cautions and disclaimers, please refer to the Sto Corp. website, www.stocorp.com.
www.stocorp.com
Property of Sto Corp. All Rights Reserved.
StoGuard® Air and Moisture Barrier
Sto Base Coat (with Sto Mesh Embedded)
Sto Primer (Optional)
Sto Finish
Sto Mesh
Light Gauge Steel Stud Framing
Sto AdhesiveSheathing
Backer Rod & Sealant
StoGuard® Air and Moisture Barrier Detail Component on Blocking; Extend onto Sheathing 2" min.
Electric Box for Fixture AttachmentBlocking
Sto EPS Insulation Board, Back-Wrapped Around Electric Box Penetration