design of ffag-erit 05/12/07 kota okabe (kek) for ffag-dds group
TRANSCRIPT
![Page 1: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/1.jpg)
Design of FFAG-ERIT
05/12/07Kota Okabe (KEK)
for FFAG-DDS group
![Page 2: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/2.jpg)
Contants
1. Back ground of this project
2. Ionization cooling
3. Design of FFAG-ERIT
4. Summary
![Page 3: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/3.jpg)
BNCT (Boron Neutron Capture Therapy)
About BNCT Boron neutron capture therapy (BNCT) is a targeted radiation therapy. BNCT is a binary approach: A boron-10 (10B) compound is administered that delivers high concentrations of 10B to the target tumor relative to surrounding normal tissues. This is followed by irradiation with thermal neutrons or epithermal neutrons that become thermalized at depth in tissues. Because range of the Alpha ray and the 7Li particles (~10 mm) is short, it is possible to treatment only the tumor cell without damaging the normal cell.
About differences usual radiation therapy and BNCT
1. BNCT make tumor selective killing without damage for adjacent normal tissue.
2. Treatment ends by one day irradiation, because the therapeutic gain is high.
![Page 4: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/4.jpg)
Neutron source for BNCT
Requirements from BNCT: In order to remedy the tumor of 10cm2, 2*1013 neutrons are needed.If we assume that remedy time is 30 minutes => Flux cm2 sec.
As a neutron source : • Nuclear reactor
• Accelerator
It have established as powerful thermal neutron source. But, it is difficult to adjoin the remedy facility and the reactor.
Generating the neutron with 7Li (p,n) and the 9Be (p,n) reaction. But average beam current >20mA is necessary, also thermal load of thetarget becomes problem.For example, it is difficult technically to achieve average beam current 20mA with linacs.
![Page 5: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/5.jpg)
What is ERIT ?
ERIT : Energy Recovering Internal TargetThe stored beam is irradiated to the internal target, it generates the neutron in the storage ring. The beam energy lost in the target is recovered by re-acceleration.
Feature of ERIT system• Average beam current of injector is suppressed.• The proton beam be sure to do track the circumference in inside the stora
ge ring. Therefore, there are no times when the charged particle exists together in the neutron beam.
The storage ring require to large acceptance(dp/p~10%) FFAGSuppression of beam heating Ionization cooling method
Proton beam power is mostly consumed by ionization in the target, not by neutron production. (Efficiency ~ <1/1000)
![Page 6: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/6.jpg)
10Be(p,n)B reaction cross section and the energy dependency
In order to obatin φ>10E9 n/cm2/s
• Neutron production reactions 9Be(p,n)B, 7Li(p,n)Be
• Proton beam energy ~10MeV current >20mA(cw)
![Page 7: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/7.jpg)
Emittance growth
Using an internal target in the ring, the beam emittance can be increased in 3-D directions by Ratherford multiple scattering and stragling
In ERIT scheme, however, the beam emittance growth can be cured by Ionization Cooling effect
![Page 8: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/8.jpg)
Ionization cooling (1)
The rate equation of beam emittance passing through a target material is,
LongitudinalLongitudinal
HorizontalHorizontal
VerticalVertical
€
dεy
ds= −
1
β 2E
dE
dsεy +
β y E s2
2β 3mpc2LR E
€
dεx
ds= −
1
β 2E
dE
ds1−
D ′ ρ
ρ 0
⎛
⎝ ⎜
⎞
⎠ ⎟εx +
β x E s2
2β 3mpc2LR E
€
d σ E2
ds= −2
∂(dE /ds)
∂E 0
+dE
ds
1
pcβD
′ ρ
ρ 0
⎛
⎝ ⎜
⎞
⎠ ⎟ σ E
2 +d ΔE 2
rms
ds
Cooling term
Heating term
E
EΔ+
E
EΔ−
0
Wedge Target Acceleration Cavity
When the wedged target is placed at
dispersive point, can be possible.
€
∂(dE /ds)
∂E
![Page 9: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/9.jpg)
Ionization cooling (2)
Energy loss rate dE/dx from Bethe-Bloch formula (9Be target)
In the light orange area the neutron is stable generated
For example, target thickness ~ 5 m
Energy loss : ΔEt ~ 35 keV
10 MeV proton beam
~ -2.82e-3
€
∂(ΔE)
∂E
Energy loss : ΔEt ~ 60 keV
5 MeV proton beam
~ -9.37e-3
€
∂(ΔE)
∂E
Beam energy 10MeV is profitable
![Page 10: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/10.jpg)
Ionization cooling (3)
x - z coupling
’ : variation of thickness
![Page 11: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/11.jpg)
Overview of FFAG-ERIT accelerator system
Injector(RFQ + DTL or IHDTL )
FFAG ring
ERIT system
RF cavity
Full energy injectionH- kinetic energy 10 [MeV]Average beam current ~ 40 [A]Repetition 1 [kHz]
H- injectionproton kinetic energy 10 [MeV]Average beam current ~ 40 [mA]
Turn number > 1000 turnInternal target thickness ~ 5 [m]Neutron beam intensity > 109 [n/cm2/sec]
RF voltage > 200 [kV]Harmonic num. ~ 5
![Page 12: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/12.jpg)
Requirement for FFAG
Radial sector type or Spiral sector type ?
Large acceptancemomentum acceptance dp/p ~ 10 [%]transverse acceptance 1000 [ mm mrad]It is necessary to adjust the phase advance to less than 90 degrees to secure a large acceptance. (from recent study, M.Aiba et al )
Separation of neutron and beamThe numbers of sectors are few, easy to take about separation.
Length of straight section (to install large RF cavity)The numbers of sectors are few, length of the straight section areeasy to guarantee.
To be the compact which can be installed in the hospitalmean radius (r0) < 2 [m]
![Page 13: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/13.jpg)
Spiral sector type (4 sector) Tune Diagram
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2 2.5Horizontal Tune
Vertival Tune
k=0.1
k=0.70.1step
Ƀ=20Åã
Ƀ=5Åã
5Åãstep
É¢ ÅÅ120ÅãÅFTune 1.33
ÅÅ90ÅãÅFTune 1.0
Lattice parameters
Cell num. = 4Open sec. angle = 90 degOpen F angle = 36 degPacking fac. = 0.4Average radius = 1.8 m
B field of F (ref.) = 0.58 [T]
![Page 14: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/14.jpg)
Spiral sector type (sector num. 8) Tune Diagram
0
0.5
1
1.5
2
2.5
0 0.5 1 1.5 2 2.5Horizontal Tune
Vertival Tune
k=2.5
Ƀ=40Åã
5Åãstep
0.1step
k=1.0
Ƀ=5Åã
É¢ ÅÅ120ÅãÅFTune 2.67
ÅÅ90ÅãÅFTune 2.0Lattice parameters
Cell num. = 8Open sec. angle = 45 degOpen F angle = 13.5 degPacking fac. = 0.3Average radius = 1.8 m
B field of F (ref.) = 0.82 [T]
![Page 15: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/15.jpg)
Spiral sector type (8 sector) Lattice parameters
Cell num. = 8Open sec. angle = 45 degOpen F angle = 13.5 degPacking fac. = 0.3K value = 2Spiral angle = 26 degAverage radius = 1.8 mB field of F (ref.) = 0.828 [T]
x = 1.89y = 1.34
maximum energy : r (Rmax) 12 [MeV] : 1.87 [m] minimum energy : r (Rmin) 8 [MeV] : 1.72 [m]
Drift length ~ 0.8 [m]
Rev. freq. (10 [MeV]) ~ 3.87 [MHz]
Used hard-edge tracking code
![Page 16: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/16.jpg)
Spiral sector type (8 sector) Twiss parameters
Fromxmax=1.48, ymax=2.03,Beam size Hori. ~ 3.8[cm] , Vert. ~ 4.5 [cm] (1000 [mm mrad])
![Page 17: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/17.jpg)
Radial sector type (8 sector) Lattice parametars
Lattice parameters
Cell num. = 8Open sec. angle = 45 degOpen F angle = 7 degOpen D/2 angle = 2 degPacking fac. = 0.4Average radius = 2.0 mK value = 2FD ratio = 7.2
B field of F (ref.) = 0.83 [T]B field of D (ref.) = 0.40 [T]
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2
horizontal tune
vertical tune
structure
3rd
2nd
1st
k=ÇQÅDÇOÅAFDÅÅÇVÅDÇQ
Rev. freq. (10 [MeV]) ~ 3.45 [MHz]
Drift length (r = 1.8 [m]) ~ 0.83 [m]
![Page 18: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/18.jpg)
Radial sector type (sector num. 8) Twiss parametars
Orbit shift (8MeV~12MeV) ~ 13 [cm]Half gap Hori. ~ 3.7 [cm] , Vert. ~ 3.9 [cm] (1000 [mm mrad])
0.5
0.6
0.7
0.8
0.9
1
1.1
1.2
1.3
0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6
s [mm]
sqrt_beta [m^1/2]
0.63
0.64
0.65
0.66
0.67
0.68
0.69
0.7
0.71
eta
sqrt_beta_H sqrt_beta_V F_mag Drift D_mag eta
![Page 19: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/19.jpg)
Radial sector type (sector num. 8) Summary
It is difficult to adjust the phase advance per sector 90 degrees when number of sector less than 8.
The size of the accelerator becomes small a spiral sector type compared with the radial sector type.
In regard to the circumstances of the tune diagram, radial sector type is the same as spiral sector type.
By selecting FD ratio, we can change the vertical tune radial sector.
It is thought that 8 sector lattice is suitable. And to develop compact machine, we chose spiral sector type.
![Page 20: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/20.jpg)
2d calculation of magnetic field
Half gap : r = 1.63 ~ 1.98[m], 8.651 [cm] r = 1.63 ~ 1.98[m], 14*(r/1.8)-2.01[cm]
![Page 21: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/21.jpg)
2d calculation of magnetic field medium plane
MMF~ 47500 [Ampare turns]
Current density(Effective coil area 65%) 7.4 [A/mm2]
r0 = 1.8 [m] : ~8240 [G]
![Page 22: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/22.jpg)
2d calculation of magnetic field local k value
166.5 < r < 195.0 [cm] : error of k value < 1%
![Page 23: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/23.jpg)
FFAG Magnet Summary
We estimated form of pole and the coil roughly with the magnetic field calculation which uses POISSON.
Presently, three dimensional magnetic field calculation which uses TOSCA is doing.
![Page 24: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/24.jpg)
One of typical RF cavity for ERIT
3 2.5
86
12
40
20
75
2
88
beam duct
panel
40
42
: [cm]
RF freq. 19.8 [MHz] Shunt impe.Rs 188 [kΩ]
Q value 13842 Driving Pow. (for 100kV) 26.6 [kw]
Calculated from MAFIA
![Page 25: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/25.jpg)
Top view of FFAG-ERIT storage ring
![Page 26: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/26.jpg)
Wedge target
0
50
100
150
200
250
0 50 100 150 200 250
X(mm)
Y(mm)
Proton beam
W
R
tt
x
Thickness of target =(1 + ( x/w ))t
Proton beamR
curve that thickness of target becomes (1+ (x/200))t
dxa
x
a
xy ⋅⎟
⎠⎞
⎜⎝⎛+⎟
⎠⎞
⎜⎝⎛=∫ 2
2
The target that changes the thickness by R is necessary for the beam cooling.
The film thickness of the part over which the beam passes is adjusted by bending the target of a constant thickness.
![Page 27: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/27.jpg)
H- injection & neutron orbit
19 deg
The electron strapping foil is shared with the target for the neutron source.
![Page 28: Design of FFAG-ERIT 05/12/07 Kota Okabe (KEK) for FFAG-DDS group](https://reader036.vdocuments.site/reader036/viewer/2022062408/56649ee85503460f94bfa3d5/html5/thumbnails/28.jpg)
Summary
Design of FFAG-ERIT system is doing. Basic parameter
We should simulate ERIT scheme using GEANT