design guide for pet bottle recyclability_31 march 2011

5/20/2018 Design Guide for PET Bottle Recyclability_31 March 2011

1

Design Guide for

PET Bottle Recyclability

Written by: Cees van Dongen - Coca-Cola Europe

Robert Dvorak / Ed Kosior - Nextek Ltd


2

UNESDA is the Union of European Beverages Association Its members are soft drinkscompanies who conduct their business in at least five EU Member States and also national

associations from across the EU27 and beyond. Our mission is to support the growth,

development and understanding of non-alcoholic beverages at a European level.

www.unesda.org

EFBW - The European Federation of Bottled Waters is a non-profit international tradeassociation based in Brussels. Our members are national associations and companies

representing the interests of over 500 producers of bottled waters across Europe. EFBW works

closely with European and international institutions which regulate on bottled water, including

the European Commission and Codex Alimentarius.www.efbw.org
http://www.efbw.org/http://www.efbw.org/http://www.efbw.org/


3

Background

The growth in processing post consumer PET bottles for high-end bottle-to-bottle application

necessitates that we review and update policies to ensure that our stringent quality standards

will continue to be met in the future.

The challenge is to maintain availability of high quality material that will, in turn, enable us to

use recycled content in bottles without discolouration and other visual defects. The quality of

recycled material over time is deteriorating through the increased use of additives, barrier

materials, glues, sleeves and other components and materials.

Following recent resolutions in the Boards of UNESDA and EFBW to work towards a PET

bottle recyclability Code of Conduct for its respective members, an agreed next step is to

review their current and new PET bottle specifications against the guidelines for resource

efficient PET recyclate to prevent and resolve issues of non-compatibility over the next twoyears.

The aim of these guidelines - a set of specific criteria and recommendations based on

current practice, recycler capabilities and the Design for Recycling Guidelines developed by

the European PET Bottle Platform (EPBP), following surveys and questionnaires to members to

identify problem areas - is also to reach as many companies as possible, not just UNESDA

and EFBW members, and encourage them to achieve compliance with the guidelines by the

end of 2012.

Also, aiming to broaden the initiative to all parties that play a decisive role in maintaining the

highest possible quality of recycled bottles, we call upon other brand owners and holders of

private labels to act likewise.

Another important aim of the guidelines is to encourage companies that design and market

materials and components intended to be used in PET bottles to apply the principle of due

diligence. We encourage them to bring their products to the European PET Bottle Platform so

as to obtain an objective third party assessment of the impact on recyclability of their

products.

Guideline details

The guidelines, which have been developed over the past year, cover specifications and

recommended design options for the body, label and cap of the bottle. All materials must

meet the legal requirements for materials and articles intended to come into contact withfood.

We believe that these guidelines are in reach of every company. They are a reflection of the

average recycler capability and try to strike a balance between resource efficiency, the need

for innovation and shelf differentiation and recycling practices in Europe.


4

Executive SummaryThese guidelines for the design of PET bottles define their ease of recyclability based on

choices of colour, barrier layers, closures and label systems and establish criteria that can beused to avoid the production of difficult to recycle bottles to ensure a greater supply of high

quality rPET to the market.

There are many resources available to packaging designers and PET bottle specifiers that

allow them to ensure that any design decisions ensure recyclability of PET bottles back into

high quality RPET resins that can be used back into bottles as part of closed loop recycling.

This report provides links to key documentation, reports and organisations that have

developed and specify protocols that determine the impact of PET bottles and components

on the PET recycling stream.

A decision making matrix has been developed by Nextek to help categorise the impacts on

recyclability of PET bottle packaging. This table, based on the Design for Recycling Guidelinesissued by PETCORE and EPBP is not an exhaustive list, but it does provide guidance on items

that are Recycle Friendly or Problematic for Recycling.

PET BOTTLE RECYCLE FRIENDLY CONDITIONAL PROBLEMATIC FOR RECYCLING

Colourants, fillersand additives

Clear / naturalLight (blue or green) tints

Dark blue / black if NIR detectableDark green and brownOptical brightenersO2scavengers;UV stabilisers;AA blockers

Non-detectable Dark, opaque, metallic,solid colourantsAny use of fillers.Nanocomposite barrier fillersBio/Oxo/Photo Degradable Additives

Barrier coatingsBlended barrier

resins & barrierlayers

Clear plasma coatings e.g. CVDSiOx, Monox

Other layered barrier materialsthat separate and do not causeyellowing

PEN / Amosorb / MXD6 barriermultilayer (if 3% in multilayerAmosorb, MXD6 > 5% in multilayer

Any direct blended barrier based on ieEVOH, MXD6

Closures HDPE / LDPE / PP - Materials density > 1 g/cm3 Metals / PS /PVC

Closure linersand seals

HDPE / PE+EVA / PP / FoamedSilicone / PET

Paper / silicone swimming valves(density 1 g/cm3)

Labels HDPE / MDPE / LDPE / LLDPE / PP/ OPP / EPSWraparound plastic

Wraparound paper labelsMetallic foils

Pressure sensitive / self-adhesive labels.PVC / PS / metallised.

Inks Non toxicFollows EUPIA Guidelines

Inks that bleed, toxic or hazardous; reactwith PET

Direct Printing Laser marked production or expirydate

Ink direct printed production orexpiry date

Any other direct printingLarge areas direct printed

Sleeves PE / PP / OPP / EPS / foamed PET& PET-G (Density < 1g/cm3).PE Stretch SleevesShrink sleeves with perforationsand revealing a significant % ofthe bottle.

Shrink sleeves with perforations andrevealing a significant % of PETbottle; Full body PET shrink sleeves

PVC / PS / PET-G, other materials withdensity > 1 g/cm3.Difficult to remove and/or NIR sort withheavy ink coverage.

Adhesives Water soluble in 60 80CPlastic wrap, Minimal glue strip(e.g. lap join).Comply with EuPR guidelines

Strong adhesives with paper labels Water insoluble (even at elevatedtemperatures and pH levels)

Base cups No base cup HDPE / PP / clear PET Coloured PET and other plastics density >1 g/cm3

Bottle SizeOthercomponents

Diameter > 50mm,Length > 100mm

Diameter 40 -50mm Diameter < 30mm,Length < 100mm.Any polymer components with density > 1

g/cm3; PVC / PLA / PS / PETGRFID tags


5

Table of contents1.0 Introduction and Objectives ............................ ................................. ................................. ............................ 6

2.0 Benefits of Adopting these Guidelines ................................ ................................. ............................... ........ 72.1 Greenhouse Gas (GHG) Savings .................................................................................................................................. 72.2 Quality and Consistency of rPET in Closed Loop Applications .................................................................... 7

3.0 Recycling in Context .............................. ................................. ................................. ................................ ....... 7

4.0 Principles of Designing for PET Bottle Recyclability ............................... ................................. ................. 84.1 Key Steps in a Typical PET Recycling Operation ................................................................................................. 8

Maximum Flake size: 12 mm ..................................................................................................................................... 10

5.0 Bottles Why Size Matters ........................................................................................................................ 10

6.0 Bottle materials, colourants and additives ............................... ................................ ............................... 116.1 Bottle Materials ................................................................................................................................................................. 11

6.2 PLA Bottles .......................................................................................................................................................................... 126.3 PVC & PS Bottles ............................................................................................................................................................. 146.4 Clarified PP Materials for Bottles ............................................................................................................................. 146.5 PET Colourants & Fillers ............................................................................................................................................... 146.6 Direct Printing on PET Bottles ................................................................................................................................... 15

7.0 Closures (closure liners & seals) ................................ ................................. ............................... ................ 167.1 Closure Liners and Seals .............................................................................................................................................. 16

8.0 Labelling systems & materials .............................. ................................. ................................ .................... 178.1 Paper Labels ....................................................................................................................................................................... 17

9.0 Sleeving systems .......................................................................................................................................... 18

9.1 Sorting of Coloured Shrink Sleeves. ....................................................................................................................... 1810.0 Label adhesives .............................. ............................... ................................. ................................. .............. 20

11.0 Barrier systems (coatings, additives, layers) ............................................ ................................. .............. 2111.1 Bio-Oxo-Photo-Degradable Additives ................................................................................................................... 22

12.0 Other Bottle Packaging Components ............................. ................................ ................................. ......... 2312.1 Other Components ......................................................................................................................................................... 2312.2 Base Cups ............................................................................................................................................................................ 23

13.0 PET Bottle Recyclability Decision Matrix ............................. ................................. ................................. ... 24

14.0 Contaminants in rPET from poorly designed bottle packaging ................................ .......................... 25

15.0 Test Protocols for Recyclability ............................................................ ................................. .................... 26

15.1 PET Flake Oven Age test .............................................................................................................................................. 2615.2 Sink Float Separation Test Protocols ..................................................................................................................... 26

15.3 Adhesives Glue Separation & Removal Test Protocols ............................................................................ 2715.4 Sorting Tests ....................................................................................................................................................................... 27

16.0 Conclusions ............................... ................................ ................................. ................................ .................... 30

17.0 Key Links, Reports & Organisations ............................... ................................ ................................. ......... 3117.1 European PET Bottle Platform ................................................................................................................................... 3217.2 PETCORE ............................................................................................................................................................................... 3317.3 APR .......................................................................................................................................................................................... 33

17.4 NAPCOR ............................................................................................................................................................................... 34

17.5 UK WRAP & BRC On-Pack Labelling Scheme for Packaging ................................................................ 3418.0 References ..................................................................................................................................................... 36


6

1.0 Introduction and Objectives

The objective of this report is to provide guidelines for PET bottle recyclability and to

overview the technical and design related aspects that can negatively impact the recycling of

PET bottles. The recycled PET (RPET) market in the European Union (EU) is still developing andissues such as material availability and input material quality have the ability to undermine the

markets potential growth in closed loop (PET) bottle-to-bottle recycling applications. The

potential to recycle bottles back into high-end applications such as bottles can be

compromised by many factors including the choice of bottle colour, bottle size, barrier layers,

closures composition, and label systems.

These guidelines provide a framework for the design of PET bottles and define the ease of

recyclability based on choices of colour, barrier layers, closures and label system types and

establish criteria that can be used to avoid the development and production of difficult to

recycle bottles to ensure a greater supply of high quality rPET to the market.

The purpose is to inform packaging designers of recycling processes and provide a

detailed technical description that allows PET bottle designers clearly understand what

recyclers want, expect and the do's and donts.

The aim is to provide clear guidance on how to prevent contamination of the clear/light

blue bottle stream that potentially can end up in bottle-to-bottle recycling for both new

pack designs as well as to allow a redesign of problematic existing bottles and their

specifications.

These guidelines also aim to establish a decision making mechanism for the design and

approval of PET bottles by defining the recyclability of PET bottle packaging materials and its

components but also by providing guidance on the use of materials and components that

need to be restricted because of their potential for detrimental contamination of PET recyclate

and interfere with current PET recycling processes.

The information provided in these guidelines will also allow for improved communication

between key department stakeholders such as sales, marketing, technical and packaging

designers and allow them to clearly discuss the potential impacts on recycling of current and

future developments in PET bottle packaging.

The following guidelines are therefore aimed at ensuring that PET bottle packaging releasedinto the EU markets is specified and designed in such a way as to maximise the potential for

the packaging to be efficiently recycled with minimal impact on the economics of existing

recycling operations and the environment.

The guidelines are aimed at providing up-to-date, consistent industry advice to those who

specify PET bottlesand decide on the details of the packaging being used. It will also help

inform brand, marketing and design functions about the impact of their selections and design

on the recyclability of the (new) PET bottle packaging.

Given that new materials are constantly being developed and packaging and recycling

technologies are also evolving, there is of course a need to periodically review and updatethese guidelines.


7

2.0 Benefits of Adopting these Guidelines

By adopting these guidelines across the PET bottle supply chain a number of benefits can be

realised. These guidelines can form the basis for inhouse bottle recyclability assessments, help

designers make better informed decisions about recyclability and can become a means for

PET bottlers, brand owners to approve new PET bottles. Like many sustainable initiatives, this

approach is not only best practice for PET recycling but also is inherently good business

practice to minimise resource use.

2.1Greenhouse Gas (GHG) Savings

Due to the threat of climate change, the impact of packaging on global warming is being

carefully considered by governments, brand owners, industry and community

environmental groups. In the UK, Coca-Cola Great Britain (CCGB) and Coca-Cola

Enterprises (CCE) have been working together with the Carbon Trust and have measured

and calculated the carbon footprints of Coca-Cola, diet Coke and Coke Zero, covering

the emissions generated from cradle to grave. The research illustrated that packaging

accounts for between 30-70% of the drinks carbon footprint and highlighted the

importance of using recycled content and of encouraging recycling post use. The study

found that a combination of these two factors can decrease the overall carbon footprint of

a product by up to 60%. (BSDA, 2009)

Life Cycle Assessment (LCA) of the benefits of recycling packaging by WRAP in the UK has

found that for every kilogram of recycled PET that is substituted for virgin PET, 1.5

kilograms of carbon dioxide (CO2) is saved (WRAP, 2006).

2.2Quality and Consistency of rPET in Closed Loop Applications

PET bottles with ideal design characteristics will help the PET recycling industry improve

the quality and consistency of supply of RPET and also improve the efficiency of closed

loop PET recycling by minimising yield losses. These improvements will allow greater rates

of usage of RPET back into closed loop PET packaging applications and lead to fewer

defects in PET bottles due to contaminants. Recyclability should have no detrimental effect

on bottle lightweighting initiatives, new designs for bottles shapes or best in class

developments.

3.0 Recycling in Context

The recyclability of PET bottle packaging is not the only aspect that should be considered

when assessing the environmental impact of packaging and products. Packaging optimisation,

efficient delivery, use of recycled content and reusability are all key aspects to be assessed

and incorporated into an overall new PET bottle design strategy.


8

Improving the consistency and degree of PET bottle recyclability is however very important as

it has significant direct and indirect impacts, including:

PET recyclate quality and end market opportunities,

Consistent supply of high quality PET recyclate back into closed loop packaging,

Economic efficiency of collection, recycling and reprocessing operations.

The PET bottle industry has made significant resource efficiency steps forward through

continual lightweighting and these guidelines are designed to complement these initiatives

and not to hamper further innovations in lightweighting.

4.0 Principles of Designing for PET Bottle Recyclability

There is a number of key overarching principles that are appropriate for all PET bottles. These

include:

Design for ease of separation and removal of materials such as closures and labels

from PET bottles to allow for ease and efficiency of recycling;

Avoidance of using materials that are known to significantly contaminate and reduce

quality of PET;

Use of fewer packaging materials on PET bottles to allow for ease and efficiency of

recycling.

4.1Key Steps in a Typical PET Recycling Operation

A: Accept flattened PET bottles in Bales

B: De-bale into single bottles

C: Remove small objects, glass, dirt, sand, loose caps, etc. via a trommel separator

D: Remove loose labels and films and other flexible packaging via ballistic separators or

hydrocyclones

E:

Remove ferrous and non-ferrous metals via magnets and eddy current systemsF: Sort into plastic type i.e. 100% PET by NIR/Optical automatic and manual sorters

G: Cut bottles into 10 mm flakes in a grinder

H: Wash flakes in hot water with detergents and caustic

I: Sink float density separation of PET and closures

J: Remove loose labels and dusty particles via hydrocyclones

K: Sort out coloured flakes away from clear flakes via optical sorters

L: Decontaminate the clear PET flakes by:

a. Decontamination, extrusion and melt-filtration of flakes into granules


9

b. Solid-state (in hot gas 200oC for 4-6 hours) PET granules to decontaminate

and increase the intrinsic viscosity (IV) by advancing the degree of

polymerisation.

Mechanical recycling processes rely on sorting techniques using near-infrared (NIR)spectroscopy to separate whole bottles, with water based washing and separating

processes also being applied. The objective is to clean and separate the different

material fractions or plastic types. The processes use differences in the density of the

materials for separation in water. Magnetic and inductive metal separators are also

employed. Materials which cannot be separated or separate incompletely remain with

the recyclate and can impair the quality of the final product. The recycling process is

therefore a step by step purification process that starts with commingled and often

dirty and mixed bottle feedstocks and ends up with washed and cleaned flake that

has been sorted to >99.9% PET purity. When the flake has reached sufficiently

acceptable purity it is ready to be decontaminated and extruded back into granules in

most of the commonly applied processes.

Figure 1.An example of density and softening temperature range for common packaging plastics


10

Figure 2.An example of a typical specification for flake purity

Property Specification

Maximum Flake size: 12 mm 95% < 12 mm

Fines (< 0.5mm or 30 mesh) < 0.3%

Material source Food grade Source (1)

Intrinsic viscosity according to ASTM D4603-96 0.76 +/- 0.02

Flake Color YI 19 max. (2)

a -

b 9 max. (2)

b 4 max. (3)

Bulk Density 300-500 kg/m3

Moisture < 0.7%

PVC < 5 ppm

Metal (aluminum, steel) < 5 ppm

Polyolefins ( HDPE, PP, LDPE,) < 50 ppm

PH rise < 0.5

The following sections of this report are aimed at helping packaging designers, technologists,

and other specifiers that design new packaging to ensure that it is highly recyclable and for

these guidelines to act as an advisory tool when redesigning or updating existing packaging.

5.0 Bottles Why Size Matters

The diameter and size of a PET bottle are important for the purpose of recovery and also to

ensure that they can effectively be ejected during sorting stages.

Small PET bottles that are typically used

for single serve drinks can be lost in

openings in trommels that are designed

to remove small contaminant particles.

Trommel screen sizes vary between 30-

50mm and can be square, rectangular or

circular in shape.

For this reason it is best that bottles have

a diameter greater than 50mm and

length greater 100mm. This size will

prevent the bottles from becoming lost

to the recycling process.


11

Bottles that have a diameter of 40-50mm are highly likely to fall through openings in trommel

screens and at most Plastic Recycling Facilities (PRFs) will end up being sent to landfill. Whilst

some recycling plants in countries such as Austria, Belgium, France and Germany are designed

to double sort and recover any lost PET products that are removed by the trommel screens,

the majority of recycling plants dont have facilities to resort or have not been designed to do

that. Therefore any small PET bottles that fall through the trommel screens are lost from therecycling stream and end up going directly to landfill.

Small bottles are also more difficult to eject due to the smaller surface area that air jets can

hit. NIR and optical sorting units use very short bursts of pressurised air to eject and remove

PET bottles by polymer type and colour type into designated hoppers.

Therefore in summary, PET bottles with small diameters < 40mm could be lost to waste

during initial stages of PET recycling when caps and glass are being removed. It is

recommended that a minimum diameter of >50mm is used. PET bottles that are shorter than

100mm may not be identified as PET bottles in automatic sorting systems, due to the

resolution used on some detectors.

6.0 Bottle materials, colourants and additives

6.1Bottle Materials

PET bottle materials specified and used by brand owners in principle should be bottle

grade PET. Different grades of PET that have slightly different intrinsic viscosities such as

those used for water, hot-fill and carbonated do not affect recyclability. It is neither the

aim of these guidelines to challenge the choice for PET or any alternative materials under

development nor to stifle innovation.

New development in plant based PET has no impact on the recycling stream, as the PET

material has not changed. The only change has been that the source of ethylene is plant

based, however the resin is polymerised and manufactured in exactly the same way,

therefore if traditional PET and plant based PET is mixed in the recycling it will not cause

any problems as there will be no difference in the materials. The development in the PET

PlantBottle resin now in use or planned to be in use by companies like Coca-Cola,

Danone and Heinz has been well communicated to the packaging and recycling industry

as can be seen in the following diagram.

Bottle Size

Recycle Friendly Conditional Problematic for Recycling

Bottle Diameter > 50mm

Bottle Length > 100mm

Bottle Diameter 40-50mm

Bottle Length < 100mm

Bottle Diameter < 30mm

Bottle Length < 100mm


12

Figure 3.Example of a well communicated change in PET resin with no impact on recycling of PET

bottles

6.2PLA Bottles

Materials that closely resemble PET such as PLA will cause significant problems in the PET

recycling stream even at very low levels (


13

PLA causes haziness in RPET products

PLA affects PET reprocessing equipment

Sticking of PET pellets in crystalliser or dryer

due to exclusion of PLA from the

crystallisation of PET

Recycling infrastructure for PLA recovery or

recycling is limited PLA bottles are only

compostable in industrial composting

systems NOT in home composters

PLA is difficult & costly to separate from PET

and increases PET recyclate losses

NAPCOR & PETCORE have rejected the

recycling of PLA along with PET

A recent evaluation report commissioned by Petcore has found that PLA in RPET at levels

even lower than 0.1% (1 bottle in a 1,000) will make any RPET resin unsuitable for most

applications and thus dramatically reduces PETs recycle value (Petcore, 2009).

Figure 4. An example of PET plaques showing haze (crystallinity) and discolouration due to PLA

contamination (Where: Sample C = 0% PLA i.e. control and Sample D = 1% PLA test (Source: PTI Europe,

2006)

Currently the presence of PLA products in the recycling stream can be considered to be

somewhat analogous to the presence of PVC. Similar to PVC, PLA can visually appear to

be very similar to PET and it is not separated from PET in a float/sink stage. Consequently

at even low levels it will cause significant loss of properties and performance of the final

recycled PET material. This scenario is distinguished from Polypropylene or Polyethylene

products where PP and PE containers are readily separated from PET with very high

efficiency by NIR sorting and also by virtue of their lower density in the sink-float density

separation process.


14

6.3PVC & PS Bottles

Materials such as PVC and PS should not be used under any circumstances for bottle packaging. PVC

and PS sink together with PET in wash and sink-float tanks and are difficult to eliminate.

PVC degrades at the temperatures that PET is processed and evolves hydrochloric acid gas,

which is corrosive and attacks PET polymer chains causing chain scission and degradationas well as corroding processing equipment. Small amounts of PVC can significantly reduce

the intrinsic viscosity of PET. Due to the degradation caused by PVC, RPET resins become

discoloured to unacceptable yellow or dark brown colour and the dechlorinated PVC

becomes brittle and creates black specs within the RPET resin.

6.4Clarified PP Materials for Bottles

PP bottles are already present in the market place, but currently dont compete with PET in

the food and beverage market. PP resin is primarily used for household, personal care and

industrial containers. PP does not have negative impacts on the PET recycle stream andrecycling processes as it can effectively separated via a combination of NIR sorting and

density (sink-float) separation techniques.

6.5PET Colourants & Fillers

The recovery of clear PET facilitates the creation of the highest value recyclate and typically

allows for closed loop bottle-to-bottle recycling.

The use of colourants should be minimised as much as possible. Translucent tints that are

very light shades of blue or green are acceptable, as these colours alter the colour of

recycled PET in a minor way and help to offset any yellowing that may occur during the

recycling process. Strong tints for example mid to dark-blue, green and brown should be

avoided whenever possible.

Where strong colours are contemplated for shelf appeal then consider using alternative

methods like sleeves, however these must be easily separated from the bottle prior to any

automatic sorting operations. (Please see section 9). Tints are always preferable to opaque

colours as they can become dispersed and do not cause haziness in recycled PET as

opaque colours do.

Black colour should be avoided where possible. Black coloured plastics are difficult to sort

unless the black colourant is NIR detectable. Very small amounts of black colourant can

significantly discolour a stream of clear / light blue PET recyclate.

Bottle Material


PETRPET

N/A PLAPVCPS


15

Coloured PET waste has a lower monetary value than clear (typically 50% lower).

The use of strongly pigmented bottles (black, white and colours) has a significant

negative impact on the quality of recycled PET since presence of small amounts of

coloured fragments can discolour recycled PET during extrusion.

The presence of coloured PET also increases the losses of clear/light blue PET duringflake sorting as for every coloured PET flake a clear PET flake is typically lost.

Fillers or masterbatch additives for example titanium dioxide, that can be used for opacity

or for lowering the cost and polymer content of the plastic should be avoided or their use

minimised. Fillers can change the density of the plastic and can also contaminate the

recycled PET stream and impact the clarity of the rPET resin.

6.6Direct Printing on PET Bottles

In the context of a growing interest for its application, direct printing of PET bottles should

be avoided. If direct printing on PET bottles is being considered, then only colours and

inks that are removable under hot wash conditions should be used. Any remaining ink on

bottle or flake surface will discolour recycled PET resin during extrusion and is likely to be

difficult to sort as printed PET bottles/flakes may still appear transparent to sensors

depending on level of ink coverage.

Inks (Direct print)


Laser marked production orexpiry dateLabel inks are non toxicFollow EUPIA Guidelines

Ink direct printed productionor expiry date

Any other direct printingLarge areas direct printedInks that bleed, toxic orhazardous; react with PET

Inks used on labels and sleeves should not bleed into water (inc. caustic hot-wash at 80C).

The EUPIA have published guidelines on inks that can be used on plastic packaging and

that are not hazardous or toxic and therefore do not introduce hazardous substances into

recycled materials. The APR has developed test protocols for testing labels and sleeves for

ink bleeding.

Bottle Colourants & Fillers


Clear / natural

Light (blue or

green) tints

Dark green, brown blue

/ black if NIR detectable

Optical brighteners

O2scavengers;

UV stabilisers;

AA blockers

Non-detectable Dark,

opaque, metallic, solid

colourants

Any use of fillers.

Nanocomposite barrier

fillers

Bio/Oxo/Photo

Degradable Additives


16

Inks on Labels & Sleeves


Label inks are non toxicFollow EUPIA Guidelines

Inks that bleed, toxic orhazardous; react with PET

7.0 Closures (closure liners & seals)

Closures should not interfere with the recycling process and should be recyclable themselves.

Ideally polymers with densities less than water i.e.


17

The EPBP concluded that APTAR Food+Beverage swimming silicone valve with a density

less than or equal to 0,95 g/cm3 will have no negative impact on current European PET

recycling (EPBP, 2010).

Therefore, all materials with a density greater than 1 g/cm3will sink along with the PET

flakes in a sink/float separation unit and will therefore be carried through the processultimately contaminating the PET. Materials with a density of less than 1 g/cm3will float

and are removed from the system with the lighter olefinic fraction.

Closure Liners & Seals


HDPE / LDPE / PP Materials density > 1 g/cm3

Metals / PS / PVC

HDPE / PE+EVA / PPFoamed Silicone / PET

Paper / silicone swimmingvalves (density 1 g/cm3)

8.0 Labelling systems & materials

Labels should be able to physically detach from the bottle and separate from the PET flakes

by specific gravity in flotation tanks or air separators. They should not leave adhesive residues

on the bottles.

Labels which best do this in the recycling process are orientated polypropylene (OPP) roll-fedlabels that use a minimal amount of adhesive and expose a significant portion of the PET

bottle are most acceptable.

Metallised or foil labels should be avoided as they may cause the bottle to be ejected to

waste by metal detectors; labels with deposition techniques that provide a very thin layer of

metal may be acceptable but need validation. Metallised paper labels although not ideal, are

always preferred to decorative and safety foils often used on bottles together with labels.

If decoration or safety/tamper proof evidence is needed it is best to use polyolefin based

stretch sleeves or paper labels. PS / PVC and PLA shrink sleeves should not be used.

8.1Paper Labels

Paper labels become wet and are often readily removable from PET bottles. However the

removal efficiency is highly dependent on the types of adhesives used on the paper label.

Any paper fibre that remains stuck on the PET flake will burn during drying and extrusion

and will contaminate the RPET granules with black specs from the carbonised paper fibre

residues.

The use of self-adhesive or pressure sensitive paper labels is less desirable as remaining

paper fibres can lead to surface defects and very small, sometimes microscopic holes

known as pinholes during blow-moulding of bottles using the recyclate.


18

9.0 Sleeving systems

LDPE stretch sleeves that cover less than 40% of the length of the bottle body are the best

choice and very acceptable to recycling. Stretch sleeves dont need to be heated and save

energy. Stretch sleeves provide good print characteristics and being PE based, oncegranulated, are readily removed during sink-float and hydrocyclone density separation stages.

Full body shrink sleeves should ideally be made from OPP (the performance of PE stretch

sleeves has improved) and still reveal a significant amount of the base PET bottle to allow

near-infrared (NIR) spectroscopic identification by automatic sorting systems. Some NIR

systems have specific programmes that can recognise fully sleeved bottles of a particular type,

pattern or print.

Overall, sleeves should be designed to be readily removable in recycling processes i.e.

perforated, so that they are dislodged from the PET bottles during the collection, baling and

debaling processes in the recycling operations.

Shrink sleeves from Polystyrene, PLA, PET-G and PVC (which sink in water along with PET

bottle flake i.e. density >1 g/cm3) should be avoided. PVC is particularly harmful to PET

recycling processes as mentioned above.

The thickness of shrink sleeves can affect NIR sorting and should typically be kept to less than

40-50 micron thickness.

Many bottle manufacturers and brand owners still use sleeves that are made from PET and in

some cases blends of OPS/PET. PVC shrink sleeves are still also used by several manufacturers.

Both PVC and OPS are harmful to PET recycling and further due to them being printed the

PET sleeves can also contaminate clear PET flake if they end up in the extruder the ink will

discolour the RPET and also become dispersed within the RPET resin, potentially

contaminating with ink solvents and other chemicals.

9.1Sorting of Coloured Shrink Sleeves.

Coloured shrink sleeves still allow a container to be identified as PET, however due to the

sleeve being coloured a clear PET bottle is often sorted into a coloured stream and

therefore lost to recycling back into bottles or sheet. This is because the optical sensor will

view a bottle with a coloured shrink sleeve as a coloured bottle even though the bottle is

actually clear. If shrink sleeves need to be used, designers should carefully consider

Labelling Systems & Materials

Recycle Friendly Conditional Problematic for RecyclingHDPE / MDPE / LDPE / LLDPE

/ PP / OPP / EPSWraparound plastic

Wraparound paper labels

Metallic foils

Pressure sensitive / self-

adhesive labels. PVC / PS /metallised.


19

material type and also perforated shrink sleeves which more easily tear during baling and

debaling and expose a section of clear PET bottle surface to the optical colour sorters.

It is possible to teach and train sensors to optimise recovery of s leeved items and

programmes exist to do this. However it is recommended that PET bottles with full body

coloured sleeves include modifications to help recyclers recover this stream into the clearPET fraction. Some suggestions include:

Some sleeve types can be designed to come off the packaging items during the

debaling process.

Sleeves can be designed to have a few clear sections to help sort items into

clear/natural stream, or

Sleeves can be designed to be removed via design features such as perforations,

which tear during baling/debaling and expose natural surface of the packaging item.

Sleeves are then removed by air classifiers.

Sleeves can be manufactured with specific markers that could be used to positivelyidentify the item into clear/natural streams, this approach is very useful when a large

volume of this sleeve type is expected in the market place.

A recent review of many MRFs and PRFs by Nextek showed that often they are currently

missing the opportunity to recover greater value from what are clear PET bottles that are

sleeved because the sorting systems eject these bottles into the coloured stream.

For packaging designers considering using full body sleeves on PET bottles, the following

considerations should be explored via trials with sorting equipment suppliers:

Clear PET bottles are typically sleeved with full body sleeves and these are typicallycoloured and therefore a sorting evaluation is needed to be performed on how the

sensors see these bottles in terms of polymer identification and colour recognition.

For example, is the underlying intensity of the signal from a clear PET bottle able to

always overcome the signal received by the sensor from the sleeve?

If the sleeve is coloured (or multi-coloured) then what decision will the sensor make

to sort this bottle into a coloured or a clear stream?

Can a system learn that a coloured sleeved bottle should be sent into a clear PET

fraction stream?

Sleeve thickness can play significant part in detection and newly developed bottleswith shrink sleeves should be tested for sorting performance.

Many shrink sleeves are multi-coloured and colour of the sleeve needs to be

carefully considered. For example, when a yellow/red sleeve section of a sleeve is

presented to the sensor, the sensor will identify it as yellow or red and be able to

successfully eject it into a coloured stream. However, if a dark colour or a black

sleeve is used it may not be able for the sensor to detect it as black is typically not

identifiable by NIR (unless non-carbon black colorant is used).

A combination of black and inappropriate sleeve thickness would result in weak NIR

characteristics and not allow the sensor to identify it as a PET polymer bottle or

determine its colour.


20

Guidelines on sleeve technology for effective removal and sensor classification need

to be developed as these will determine sleeve design and manufacture and

ultimately help improve the recovery of clear PET bottles with full body coloured

sleeves, currently classified as coloured PET bottles.

10.0Label adhesives

The amount of adhesive and surface coverage should be minimised to reduce contamination

during recycling.

Water-soluble or alkali soluble adhesives are preferred. Adhesives that cannot be removed

remain coated to the flakes and can embed undesirable contaminants. The use of thermoset

polyurethane adhesives is particularly problematic.

The European Plastics Recyclers (EuPR) has issued a list of hot-melt adhesives acceptable for

inclusion in mechanical recycling operations

(http://www.plasticsrecyclers.eu/docs/docs/useful006.pdf). Adhesives classified as good show

removal rates of greater than 90%.

The Association of Post Consumer Plastic Recyclers (APR) has developed testing protocols to

evaluate the impact of adhesives on bottle reclamation systems

(http://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asp).

The European PET Bottle Platform(EPBP) has developed testing protocols for adhesive

manufacturers and packaging producers to evaluate the impact of adhesive products inconventional PET recycling systems.

http://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdf

It is recommended that where possible, the glue be applied in a very thin layer and only act

as lap joint. With any new label development designers should perform glue separation tests

and check that the label glue is on the EUPR approved glue list, the adhesive should separate

from PET flakes during the hot caustic water wash step. Label adhesives should be water

soluble or dispersible at temperatures between 60C and 85C in order to be removed in

conventional washing and separation systems. If adhesives are not removed efficiently, they

may disperse and re-deposit on the PET flake regrind and embed unwanted contaminants.

The use of hot melt adhesives is undesirable and should be avoided unless the adhesive

Sleeves


PE Stretch Sleeves preferred

PE / PP / OPP / EPS / foamed

PET &PET-G (Density < 1g/cm3).

Shrink sleeves with perforations

and revealing a significant % of

the bottle to allow detection of

clear PET bottle.

Shrink sleeves with perforations

and revealing a significant % of

PET bottle; Full body PET shrink

sleeves

PVC / PS / PLA / PET-G, other

material with density > 1 g/cm3.

Difficult to remove and/or NIR

sort with heavy ink coverage.
http://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdf


21

readily separates from the plastic and does not cause problems in the reclaiming process. The

use of other non soluble adhesive types is discouraged and should be avoided.

11.0Barrier systems (coatings, additives, layers)

Monolayer PET packaging with minimal other materials results in the cleanest end-product.

There are certain products such as oxygen sensitive juices that require long shelf life

protection and the only way to achieve this is with a functional barrier, however reducing the

use of barrier layers for products where barrier requirements are minimal is important. Often

barrier material amounts are over specified, as a precaution and these high levels of barrier

materials impact the recycling stream.

There are currently many ongoing developments and innovations in barrier materials and

many of these offer enormous growth opportunities for the PET industry, lightweighting

opportunities also provide wider packaging options for beverage producers. But the barrier

materials are not PET based and the introduction of non-PET material may represent a

difficult-to-remove contaminant that could adversely impact recycling. If the new barrier

packaging is not designed for recyclability, downstream costs may increase due to the

problems with removing the non-PET components.

Barriers are typically needed to meet the requirements of specific product applications e.g.

protection from either light or oxygen. Barrier materials can be internal, external or middle

layers and may be difficult to separate from the PET layers and can therefore hinder recycling.

Some barrier systems are more compatible than others in recycling and each system will

require a detailed evaluation prior to selection. EPBP issues regular updates of barrier and

blocker systems that have passed recyclability tests. In most cases these approvals areconditional, meaning that the use of these materials in PET bottles is limited to a certain

weight percentage of the bottle and/or relative proportion of these bottles in the

marketplace. This information can be found on EPBPs website.

In general the use of non-PET layers and coatings are detrimental to the recycling process

and should be minimised wherever possible. In some cases using a heavier PET only bottle

may still achieve functional and economic objectives without contamination. Where their use

is unavoidable they should ideally be easily removable e.g. plasma based coatings (SiOx) or

blended additives that are compatible with PET such as Monox. Polyethylene napthalate (PEN)

that is less than 3% of the bottle weight or some nylons e.g. MXD6, which can be at least

partially separated by mechanical action may be tolerable in some systems. Barrier materialscontaining EVOH and MXD6 have the potential to cause discolouration during PET recyclate

Adhesives


Water soluble in 60 80CPlastic wrap, Minimal gluestrip (e.g. lap join).Comply with EuPR guidelines

Strong adhesives with paperlabels

Water insoluble (even atelevated temperatures andpH levels)


22

reprocessing. Whilst MXD6 does not cause major problems to recycling it does have the

potential to cause some discolouration.

The Technical Committee of the European PET Bottle Platform (EPBP) in 2010 evaluated the

effect of MXD6 co-injected bottles on the quality of recycled PET. The co-injected bottles

consisted of a thin layer of MXD6 as the middle layer of a 3-layer construction with noadhesive tie layers and a content of approximately 5% MXD6. Data supplied from tests

(carried out according to the EPBP testing protocol) demonstrated that processing conditions

and bottle performances were not affected by relatively high percentages of MXD6 co-

injected bottles. However, residual colour was found to be a limiting factor, although the

MXD6 middle layer was able to be partially removed (by air elutriation) from the inner and

outer PET layer during the PET recycling process.

EPBP have stated that the co-injected bottles with MXD6 should be used only under the

following conditions:

the preform must be injected so that the MXD6 layer is only in the bottle wall with a

maximum of 5% Nylon MXD6;

the bottle must be 3-layer construction with no tie layers;

the concentration of these bottles is limited at a level up to 2% in the PET bottle

market.

If these conditions are met then based on the assessments outcome and current markets

knowledge of MXD6 in 2010 the EPBP concluded that Mitsubishi Gas Chemical MXD6 co-

injected bottles coating will have no negative impact on current European PET recycling

(EPBP, 2010).

Therefore, provided that barrier materials such as MXD6 in the PET recycle stream are kept at

very low levels then the impacts on recycled PET are believed to be minimal, however if the

use of these barrier materials becomes more common or if they start to be used in a product

with large volumes then there will be impacts such as discolouration and yellowing of

recycled PET.

PETCORE have proposed test guidelines to determine the impacts of barrier materials and

technologies on the PET recyclate stream and include:

Yellowness Index and determination of flake colour (Doc P-0);

Evaluation of the influence of additives or barrier materials in the production andproperties of bottles containing R-PET (Doc P-4);

Evaluation of delamination and removal of barrier materials or additives during the

reclaim process (Doc R-1).

11.1 Bio-Oxo-Photo-Degradable Additives

A number of companies have started to offer bio-oxo-photo degradable additives for

PET bottles. Misleading claims have been made that these additives will help bottles

that end up as litter degrade in soil or marine environments. This is not true as PET

does not readily degrade, so although the additives may break the bottle structuredown, small particles and PET fragments will remain.


23

This approach has serious implications as it has the

potential to degrade PET materials and have serious

impacts on the recycled resins. DEFRA in the UK have

published a study stating that packaging containing

these additives could cause problems for recycling andthat products should be incinerated not composted.

These additives break down and are believed to leave

behind various sizes of PET fragments, which can be

highly dangerous to wildlife and result in accumulation

of fine plastic particles in the environment. Any bio,

oxo, photo degradable additives need to be avoided as

they not only do not provide any environmental or

functional benefits, they cannot be readily sorted and

may be detrimental to the existing recycling

infrastructure

12.0Other Bottle Packaging Components

12.1 Other Components

The use of other components e.g. handles, pouring spouts, sports caps etc is discouraged

unless they can be easily separated in flotation tanks (e.g. have a density of < 1 g/cm3) or

are unpigmented compatible materials.

Price tags where used should be attached to the closure or the label.

The use of RFID tags needs to be individually assessed to ensure that they can be easily

removed and separated. Where possible it is best to avoid the use of RFID tags.

The use of PVC, PLA and PETG should be avoided wherever possible as these materials

significantly interfere with PET recycling systems, since they have an appearance very

similar to PET they become included with the PET bottles prior to the recycling process.

These materials are of overlapping density (>1g / cm3

) so get carried through thereprocessing system, where due to their lower melting point, they cause the formation of

degraded black particles (PVC) and agglomerations of flakes and granules (PLA and PETG)

that can ruin many tonnes of otherwise high quality recyclate

12.2 Base Cups

Base cups are rarely used on economic grounds and preferably should not be used.

However if at any time their use were to be considered then they should be made from

HDPE / PP or clear PET and never be made in coloured PET.


24

13.0PET Bottle Recyclability Decision Matrix

PET BOTTLE RECYCLE FRIENDLY CONDITIONAL PROBLEMATIC FOR

RECYCLING

Colourants,

fillers and

additives

Clear / natural

Light (blue or green) tints

Dark blue / black if NIR

detectable

Dark green and brown

Optical brighteners

O2scavengers;

UV stabilisers;

AA blockers

Non-detectable Dark,

opaque, metallic, solid

colourants

Any use of fillers.

Nanocomposite barrier

fillers

Bio/Oxo/Photo

Degradable Additives

Barrier coatings

Blended barrier

resins & barrier

layers

Clear plasma coatings e.g.

CVD* SiOx, Monox

Other blended barrier

materials that separateand do not cause

yellowing

PEN / Amasorb / MXD6

barrier layer (if 3%

Amasorb > 5%

MXD6 > 5%

Closures HDPE / LDPE / PP - Materials density > 1

g/cm3 Metals / PS / PVC

Closure liners

and seals

HDPE / PE+EVA / PP /

Foamed Silicone / PET

Paper / silicone

swimming valves (density

1

g/cm3)

Labels HDPE / MDPE / LDPE /

LLDPE / PP / OPP / EPS

Wraparound plastic

Wraparound paper labels

Metallic foils

Pressure sensitive / self-

adhesive labels. PVC / PS /

metallised.

Inks Non toxic

Follows EUPIA Guidelines

Inks that bleed, toxic or

hazardous; react with PET

Direct Printing Laser marked production

or expiry date

Ink direct printed

production or expiry date

Any other direct printing

Large areas direct printed

Sleeves PE / PP / OPP / EPS /

foamed PET (Density 1 g/cm3.

Difficult to remove and/or

NIR sort with heavy ink

coverage.

Adhesives Water soluble in 60 80C

Plastic wrap, Minimal glue

strip (e.g. lap join).

Comply with EuPR

guidelines

Strong adhesives withpaper labels

Water insoluble (even atelevated temperatures and

pH levels)

Base cups No base cup HDPE / PP / clear PET Coloured PET and other

plastics density > 1 g/cm3

Bottle Size

Other

components

Diameter > 50mm,

Length > 100mm

Diameter 40 -50mm Diameter < 30mm,

Length < 100mm.

Any polymer components

with density > 1 g/cm3;

PVC / PLA / PS / PETGRFID tags


25

14.0Contaminants in rPET from poorly designed bottle

packaging

Recycled PET is affected by contaminants from poorly designed PET bottles but also many

types of packaging products that end up in the commingled packaging waste stream.

The following is a list of often found contaminants that regularly end up in recycled PET

resins:

Black Specs are found in almost all recycled PET resins. Although RPET resins are melt

filtered down to very fine levels (60-100 micron) degraded particles from burnt paper label

fibres or degraded PVC black specs break apart and contaminate RPET resins. Black specs

are the end result of poorly chosen components such as paper labels or PVC shrink

sleeves.

PLAcontamination is relatively new in the PET industry, but is a growing threat. PLA is

difficult to identify in PET flake and during extrusion will phase separate potentially causing

problems during solid stating as the granules with PLA contamination will become tacky.

When RPET is processed into bottles any presence of PLA contamination will cause

haziness due to induced crystallinity. There are a few PLA bottles present in the EU/UK

bottle market, however PLA is becoming popular for thermoformed packaging and PLA

labels have now entered marketplace and these will cause problems for PET bottle

recycling. PLA labels or sleeves should be avoided for use with PET bottle packaging.

PVC contaminants cause black specs in RPET, discolouration and a drop in the intrinsic

viscosity of RPET.

PETGis often mistaken as PET. However PETG has greater melt strength than PET and is

often used for wide mouth jars and can cause gels and other processing problems. PETG

should be avoided where possible.

PS/OPS/HIPScause problems for RPET resin during reprocessing and cross contamination

with PS/HIPS will often result in bottle defects. Many PET bottle designers still use OPS for

sleeves or for labels on PET bottles. Labels or sleeves should be made from polyolefinic

materials such as xxxxxxxx?

Siliconecontamination has increased due to the popularity of leak resistant silicone valvesand also silicone valves in sport drink caps. Silicone valves cause gels and defects in

products made from RPET that contains silicone contaminants. Silicone valves should be

foamed or have a density less than 1gm/cm3or be designed in such a way that once a cap

is granulated the silicone floats and is removed with the polyolefinic cap material.

Adhesive contamination results in yellowing of recycled PET. Certain adhesives can also

cause the formation of gels and haziness within the RPET resin and products.

Aluminiumcontaminants found in RPET come from two sources, namely aluminium foils

or residual particles from aluminium cans. Aluminium contaminants are usually removed

when melt-filtered, however if they get past a filter screen they are seen as serious


26

contaminants that result in products being put on hold or recalled. Aluminium components

in PET bottle packaging need to be avoided.

Metal contaminants typically from springs in trigger packs or metal closures. These can

cause serious problems if they get past a filtration system and result in product recalls or

packaging products being put on-hold and re-sorted. Metals need to be avoided in PETbottle packaging.

Coloured PET/Other Coloured Plastics cause discolouration of extruded recycled PET

resin. The level of discolouration is typically related to the colour types and the amount of

coloured contaminants present. Coloured PET shrink sleeves will be identified as PET and

will in many cases contaminate clear PET bottle flakes. Whilst better than PVC/OPS shrink

sleeves they will cause discolouration as they often heavily printed and the ink will

discolour and contaminate the RPET during melt reprocessing (extrusion).

15.0

Test Protocols for Recyclability

15.1 PET Flake Oven Age test

A PET flake oven age test is performed by every recycler. This test allows recycling

companies to quickly see what happens to the flake materials before they are extruded

and what types of contaminants are present. For example PVC contaminants will degrade

and turn brown or black and will therefore be easily identified and their levels measured in

parts per million (ppm).

The oven aging test is designed to allows QA/QC staff to measure impurities, additives,

coatings or glues that discolour during a heating step. Materials with low softening

temperatures such as polyolefins and PLA will become tacky and can also be readily

identified and their levels measure.

In the test, a known quantity of a PET flake sample is heated to 220 C for 60 minutes.

During this thermal treatment, degradation of certain components in the sample will cause

the contaminants to discolour, making it possible to be visually detected in the sample.

PET flakes with attached glues will become yellow or even brown on surface. After 60

minutes the flake samples are removed from the oven and inspected for discolouration,

flakes with glues, degraded materials, clusters due to polymers that become tacky and

stick to PET. Some recyclers also measure the L-a-b values of the oven aged flake samples

to determine, likely discolouration that may occur during further thermal treatments such

as extrusion or solid stating. An oven age test protocol has been developed by EPBP

http://www.petbottleplatform.eu/downloads/public/EPBP_QT500_-_oventest_(2010).pdf

15.2 Sink Float Separation Test Protocols

A sink-float test can be readily performed by most packaging designers as it typically uses

water to separate PET flakes from other components such as caps, labels and closure

valves.
http://www.petbottleplatform.eu/downloads/public/EPBP_QT500_-_oventest_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT500_-_oventest_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT500_-_oventest_(2010).pdf


27

The European PET Bottle Platform (EPBP) organization has developed a test protocol for

sink-float testing. Sink floatation is an easy and efficient, density based separation method

used to separate light, floating components such as caps and labels from heavy

components that sink, such as granulated PET bottles flakes. Non-PET materials and

components that sink together with PET flakes cause serious processing inefficiencies

which limit the use of rPET in applications such as bottles. Combinations of PET with othermaterial types that sink in water should be avoided on all PET bottle packaging (EPBP,

2010) http://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-

_sink_float_separation_(2010).pdf

15.3 Adhesives Glue Separation & Removal Test Protocols

Where possible the use of glue on PET bottle surface should be avoided, however if this

cannot be achieved, soluble glues and small amounts and areas covered should be the

objective.

The European Plastics Recyclers (EuPR) has issued a list of hotmelt adhesives acceptable for

inclusion in mechanical recycling operations

(http://www.plasticsrecyclers.eu/docs/docs/useful006.pdf). Adhesives classified as good

show removal rates of greater than 90%.

The Association of Post Consumer Plastic Recyclers (APR) has developed testing protocols

to evaluate the impact of adhesives on bottle reclamation systems

(http://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.as

p).

The EPBP has developed glue test assessment protocol

http://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-

_glue_separation_(2010).pdf

These protocols are widely recognised by the recycling industry as they have been

developed through direct consultation with many recyclers and have been proven to

provide quick and accurate assessments of glue separation.

15.4 Sorting Tests

There are currently no specific protocols that specify sorting performance. The European

PET Bottle Platform has suggested that NIR and Colour detection accuracy of 80-90% may

be acceptable.

For many recyclers, sorting performance is the key to achieving high purity rPET resins. For

this reason it is recommended that before new PET bottle packaging is placed into the

marketplace it should be checked for detectability by NIR and optical colour sorting

systems. All polymers have unique spectroscopic signatures that allow them to be

identified and sorted into individual polymer streams. The majority of modern automated

sorting systems use Near Infra-Red (NIR) Spectroscopy to identify the polymer type.
http://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-_sink_float_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-_sink_float_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-_sink_float_separation_(2010).pdfhttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT504_-_glue_separation_(2010).pdfhttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecycling.org/technical_resources/testing/pet_flake_contamination_test.asphttp://www.plasticsrecyclers.eu/docs/docs/useful006.pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-_sink_float_separation_(2010).pdfhttp://www.petbottleplatform.eu/downloads/public/EPBP_QT502_-_sink_float_separation_(2010).pdf


28

Figure 5.An example of the spectroscopic profile of various polymers

The following picture shows an example of an NIR identification of a medium sized PLA bottle

and a larger PET bottle. The sensor is able to distinguish the different polymer types and also

the size of the bottles and all the important and necessary information for the ejection of

these bottles.

Figure 6.Example of an NIR screen reading showing a signal for a PLA bottle and PET bottle.

Bottle packaging designers also need to consider the impact of different bottle shapes and

sizes and how these variables can effect sorting. As previously described, small bottles are

difficult to identify especially if covered in large labels or sleeves and can also be difficult to

eject. Certain bottle shapes can be difficult to flatten during baling and bottles that are not

sufficiently flattened can roll around on the sorting conveyor belt, making identification and

detection for the sensor difficult.

New developments in sorting include the use of so called laser flake sorting systems which

utilise wide spectrum (UV-Vis-NIR-MID) measurement of the polymer spectroscopic signature.Although currently expensive and not widely used, these systems are likely to become more


29

widespread as costs come down. and will be important in sorting of flakes where they are

highly effective at removing contaminants such as Silicone, PVC, PLA and other non-PET

materials. X-Ray Fluorescence (XRF) systems are occasionally used to help separate PVC from

PET as XRF systems can readily detect the chlorine component in PVC.

Optical sensors that utilise colour databases and detect in the visible spectrum are used toseparate bottles by colour. The majority of recyclers only sort PET into two fractions:

Clear & Light Blue

Mixed Colours (Jazz)

Provided that the volumes of coloured PET justify the investment and infrastructure in sorting

equipment, some recently built sophisticated recycling plants sort into coloured PET into a

number of colour streams such as:

Clear & Light Blue

Dark Blue

Green

Mixed Colours (Amber, Brown, Yellow, Red, Black, White, Purple, Orange, etc)

It is typically not commercially viable to separate all colours into individual streams. Coloured

PET waste streams that contain a mix of colours are diverted away from high value closed

loop recycling (i.e. bottle-to-bottle or bottle-to-sheet) and are primarily used for strapping

and fibre applications.

NIR bottle sorting systems are now capable of sorting mixed materials to high purity rates of

95-98% at high throughput rates of 3-5 tonnes per hour. In Europe a number of specialised

NIR bottle sorting equipment manufacturers exist:

TITECH (Germany)http://www.titech.com/

S+S Separation and Sorting Technology (Germany)http://www.sesotec.com/

Pellenc Selective Technologies (France)http://www.pellencst.com/en/

RTT (Germany)http://www.rtt-zittau.de/en/

Binder +Co AG (Austria)http://www.binder-co.com/

BT-Wolfgang Binder GmbH (Austria)http://www.redwave.at

These companies all regularly perform both static and dynamic sorting tests to determine

sorting efficiency of newly developed packaging and they can also provide feedback on sort

accuracy and achieved purity rates as well as highlight any potential problems before the

bottles enter the marketplace and the recycling stream. It is recommended that these

suppliers be consulted either directly, via recycling operations or industry bodies such as

EPBP, to evaluate new bottle designs.

Flake sorting systems have traditionally been used to optically separate clear flake plastic

materials from coloured plastic materials. In the last 2 years several companies have
http://www.titech.com/http://www.sesotec.com/http://www.pellencst.com/en/http://www.rtt-zittau.de/en/http://www.binder-co.com/http://www.redwave.at/http://www.redwave.at/http://www.binder-co.com/http://www.rtt-zittau.de/en/http://www.pellencst.com/en/http://www.sesotec.com/http://www.titech.com/


30

developed NIR based flake sorting systems and a wide spectrum laser sorting system has

been developed by UNISENSOR. A number of flaking sorting equipment manufacturers based

in Europe can perform inhouse tests that may help packaging designers understand potential

impacts of bottle design and components on flake sorting performance. The key flake sorting

suppliers include:

TITECH Autosort (Flake) (Germany)http://www.titech.com/

S+S Separation and Sorting Technology (FLAKE PURIFIER) (Germany)

http://www.sesotec.com/

UNISENSOR Powersort 200 (Germany)http://www.unisensor.de/

ViSys Cleantech (Belgium)http://www.visysrecycling.com/

SEA (Italy)http://www.seasort.com/

Buhler Sortex (UK)http://www.buhlergroup.com/global/en/process-

technologies/optical-sorting.htm

16.0Conclusions

Using these guidelines as a tool to aid the review of current packaging and the development

of new packaging will help packaging designers, sales and marketing staff to avoid the use of

materials or combinations of materials that might create problems in collecting, sorting or

recycling PET bottles.

The use of the guidelines will also drive a market change, as more bottles move to highly

recyclable categories which will continue to improve the overall quality of recycled PET as well

as the quantity of high quality of PET recyclate available for reuse back into bottles. This

change will allow more widespread use of rPET at higher incorporation rates and reduce the

amount of material that is currently being downgraded due to impurities or poor colour.
http://www.titech.com/http://www.sesotec.com/http://www.unisensor.de/http://www.visysrecycling.com/http://www.seasort.com/http://www.buhlergroup.com/global/en/process-technologies/optical-sorting.htmhttp://www.buhlergroup.com/global/en/process-technologies/optical-sorting.htmhttp://www.buhlergroup.com/global/en/process-technologies/optical-sorting.htmhttp://www.buhlergroup.com/global/en/process-technologies/optical-sorting.htmhttp://www.seasort.com/http://www.visysrecycling.com/http://www.unisensor.de/http://www.sesotec.com/http://www.titech.com/


31

17.0Key Links, Reports & Organisations

The following documents provide guidance on general eco-design principles for PET bottlesand other plastic packaging formats. It is recommended that packaging designers become

familiar with the key principles discussed within these documents. Whilst there are some

differences on the recyclability and categorisation of different packaging, many of these

documents outline

Best Practices and Industry Standards in PET Plastic Recycling, NAPCOR, 1997

Conception et Fabrication des Emballages en Matiere Plastique pour une Valorisation

Optimisee,Chambre Symdicale des Emballages en Matiere Plastique (CSEMP)

Design for Recycling Guidelines; Designing Plastic Bottles to be Recyclable, Keith Bechard

Entropex Oct 2009, The Association of Postconsumer Plastic Recyclers

Designing Recycling-Friendly Plastic Sales Packaging: A discussion paper for Packaging

Designers, DKR, Sep 2001

Designing recyclable plastic bottles, Comite Technique de Recyclage des Emballages

Plastiques (COTREP) Jan 2004

European PET Bottle Platform: PET Recycling Test Protocol, February 2010, EPBP,

www.petbottleplatform.eu

Exclusion List for Printing Inks and Related Products, 5thedition Oct 2007, Eupia.org

Guidelines on Acceptability of Additives and materials in PET Waste Stream for an

Efficient Recycling of PET, Petcore

Packaging Design for the Environment: Reducing Costs and QuantitiesGG360, Envirowise

Guide

Packaging, Material recycling, report on requirements for substances and materials to

prevent a sustained impediment to recycling. CEN 13688, Apr 2000

Packguide: A Guide to Packaging Eco-Design, Incpen, GG908, Envirowise Guide

PET Bottles, Design for Recyclability Guidelines, The Association of Postconsumer Plastic

Recyclers

PET Bleeding Label Test, Testing, Technical Resources, The Association of Postconsumer

Plastic Recyclers

PET Flake Contamination Test, Testing, Technical Resources, The Association of

Postconsumer Plastic Recyclers


32

Positive Glue List, European Plastics Recyclers (EuPR) Version 1, Approved April 2001

Plastics packaging, Recyclability by Design, Recoup, revised edition 2009

Voluntary Design Guidelines for Designated PET Bottles, Apr 2001, The Council for PET

Bottle Recycling

17.1 European PET Bottle Platform

The European PET Bottle Platform (EPBP) is a voluntary initiative supported by the

European Association of Plastic Recycling and Recovery Organisations (EPRO), the

European Plastics Recyclers (EUPR), PET containers recycling Europe (Petcore), the European

non-alcoholic beverages association (UNESDA) and The European Federation of Bottled

Waters (EFBW).

The main objective of the European PET Bottle Platform is to evaluate technologies /products and to allow new PET bottle innovations, while minimising the economic and

environmental consequences for the European PET recycling industry.

It plans to do so by promoting the recyclability of PET bottles on the market by:

Establishing European harmonised guidelines for PET bottles recyclability that will be

accepted across the whole value chain.

Encouraging industry to test new PET bottle concepts and/or materials before market

launch according to the harmonised guidelines.

Giving advice and recommendations to the different stakeholders.

Sharing information and knowledge across the whole value chain.

The Platform is grouping technical experts in the field of PET production, design and

recycling for an objective evaluation of new technologies and an independent assessment

of their impact on the PET recycling processes across Europe. For this, the Platform has

established several test procedures in order to assess the recycling profile of new

packaging technologies, such as barriers, additives, closures, labels, etc. Products that pass

the tests should not experience any problems during recycling.

The European PET Bottle Platform has established several test procedures to assess the

influence of PET bottle innovations - such as barrier materials, resin formulations, additivesand non-PET components in or on PET bottles - on RPET recycling processes. Non-PET

components in new or innovative PET bottles may affect specific properties of RPET which

are relevant for its re-use as secondary raw material in applications such as bottles, film,

sheet, strapping and fibre.

The first set of test procedures are relatively rapid and low-cost techniques for the quick

assessment of the recycling profile of PET bottles. All quick tests include a complete

explanation of the scope, techniques, equipment and test conditions, as well as a

summary interpretation explaining how to use the test results.The results of the quick

tests are purely indicative, and are often used for the optimisation of further tests.

EPBP has also developed a test protocol for innovative PET bottles. This protocol isdesigned to evaluate PET packaging solutions that generally end up in the PET recycling


33

stream and that can possibly influence the quality of - or even disturb - the recycling

system. Their experts will use the information provided by the applicant, combined with its

expertise and knowledge database, to determine the optimal test program, using up-to-

date testing methods that produce qualitative and/or quantitative test results. Products

that pass the tests should not experience any problems during recycling.

For further information visit:http://www.petbottleplatform.eu/index.php

17.2 PETCORE

PETCORE, PET COntainers REcycling Europe, is a European association fostering the use

and development of PET containers and facilitating both PET recycling and the

development of recycled end material. Petcore has members from many sectors of the

PET industry and today it sees a wide representation from many sectors of the business:

resin producers, containers manufacturers, bottle end-users and recyclers. Petcore assists

local authorities in establishing PET containers recycling programmes and maintains closerelationships with European national associations dedicated to the recovery and recycling

of PET containers. Petcore has developed a sound know-how in the establishment of

recycling programmes and can assist communities with pertinent information about the

processing, reclamation and re manufacture of post-consumer containers.

In order to foster PET packaging usage, Petcore believes that PET packaging development,

design, promotion and the collection and recycling of post-consumer PET containers, must

be based on the three pillars of sustainability. PET packaging development as a whole

must therefore be:

economically sound

environmentally justified

socially accepted

For further information visit:www.petcore.org

17.3 APR

The Association of Postconsumer Plastic Recyclers (APR) in the USA is the national trade

association representing companies who acquire, reprocess and sell the output of more

than 90 percent of the post-consumer plastic processing capacity in North America. APRstrongly advocates the recycling of all post-consumer plastic packaging. APR promotes

development of the plastics recycling industry by providing leadership for long-term

industry growth and vitality. APR strives to expand the post-consumer plastics recycling

industry through a cooperative effort aimed at identifying and eliminating barriers to

successful commercial recycling by:

Developing protocols for the design of packaging for greater recyclability.

Improving the quality of post-consumer plastics entering the system.

Fostering a strong interface with end-user markets.

Promoting a cooperative testing program for new packaging.

Encouraging design for recyclability with guidelines and programs.
http://www.petbottleplatform.eu/index.phphttp://www.petbottleplatform.eu/index.phphttp://www.petbottleplatform.eu/index.phphttp://www.petcore.org/http://www.petcore.org/http://www.petcore.org/http://www.petcore.org/http://www.petbottleplatform.eu/index.php


34

APRs Technical Committee has established and updated guidelines for the design, the

recyclability and standards for good recycling practices along with researching new

technologies.

APR also works very closely with other industry organizations such as the National

Recycling Coalition, the American Plastics Council and the National Association for PET

Container Resources.

For further information visit:http://www.plasticsrecycling.org

17.4 NAPCOR

The National Association for PET Container Resources (NAPCOR) is the trade association

for the PET plastic industry. They promote the introduction and use of PET packaging,

facilitate the recycling of PET packaging, and communicate the attributes of the PET

container as an environmentally sustainable package. NAPCOR have developed PET

recyclability guidelines and provide information on best practices in recycling.

For further information visit:http://www.napcor.com/

17.5 UK WRAP & BRC On-Pack Labelling Scheme for Packaging

In the United Kingdom, BRC, WRAP and LARAC all measure the recyclability of packaging,

including PET bottles.

The assessment is based on the 3 on-pack label BRC categories

design guide for pet bottle recyclability_31 march 2011

Documents