Gear Guard™ Mobile STEM Workstation Assembly

Instructions

Parts List:(1) Base with Casters and Rim(1) Center Shelf with Rim(2) Gear Guard Panels(2) End Panels

Assembly tips: Assemble the workstation on a tarp or piece of cardboard to protect against scratches. Rubbing bar soap on the Bolts will lubricate the threads for easier assembly.

Position the Center Shelf, Tabletop, and Gear Guard Panels1. Lay one End Panel flat on the floor as shown in fig. 1. Place (8) Dowels in the face of the panel — see fig. 1 for locations.2. Position the Center Shelf as shown in fig. 2. Pivot the shelf vertically onto its left edge. Press over the Center Shelf Dowels in

the End Panel (see fig. 1). The Dowels should hold the shelf in place.3. Position the Tabletop as shown in fig. 3. Pivot the Tabletop vertically onto its left edge. Press over the Tabletop Dowels in

the End Panel. The Dowels should hold the Tabletop in place.4. Position the Gear Guard Panels as shown in fig. 4. Pivot one panel vertically onto its left edge. Press over the Gear Guard

Dowels in the front edge of the End Panel. Pivot the remaining Gear Guard Panel onto its right edge. Press over the GearGuard Dowels in the back edge of the End Panel. The Dowels should hold the panels in place.

Attach the second End Panel5. Place (8) Dowels in the exposed ends of the Center Shelf, Tabletop, and Gear Guard Panels — see fig. 2–4 for locations.6. Position the remaining End Panel as shown in fig. 5. Press the panel over the Dowels with the outer side facing up.7. Using the Allen Wrench, screw (8) Bolts through the outside of the End Panel — see fig. 5 for locations. Do not tighten fully.

Attach the Gear Guard Panels8. Using the Allen Wrench, screw (6) Bolts through the Gear Guard Panels — see fig. 4 for locations. Do not tighten fully.

Fasten the unsecured End Panel9. Pivot the workstation to the left and onto its top — be careful to keep the unsecured End Panel in place as you pivot.10. Using the Allen Wrench, screw (8) Bolts through the outside of the End Panel — see fig. 5 for locations. Do not tighten fully.

Attach the Base11. Insert (4) Dowels in the exposed edges of the End Panels — see fig. 1 for locations.12. Position the Base as shown in fig. 6. Press the Base over the Dowels with the casters facing up. Be sure to align the rim with

the back of the workstation. Using the Allen Wrench, fully tighten (6) Bolts through the Base — see fig. 6 for locations.

Complete Assembly13. Use the Allen Wrench to fully tighten all bolts in the End Panels and Gear Guard Panels. Lock the casters and pivot the

workstation onto its base to complete assembly.

(1) Tabletop(28) Bolts(16) Wood DowelsTools required: Allen Wrench — included

www.demco.com

WARNING:CHOKING HAZARD — Assembly hardware contains small parts. Adult assembly required.

!

Assembled — Side Assembled — BackAssembled — Front

Tabletop

Gear GuardPanels

Center Shelfwith Rim

Side Panels

Base withCasters & Rim

Questions? Contact Demco Customer Service (7:30 a.m.–5 p.m. CT Monday–Friday) at 800.962.4463 or custserv@demco.com.

Find Demco® Gear Guard™ Mobile STEM Workstation @demco.com, search 13789430

Call 800.962.4463 or email custserv@demco.com

Questions? Contact Demco Customer Service (7:30 a.m.–5 p.m. CT Monday–Friday) at 800.962.4463 or custserv@demco.com. www.demco.com

Gear Guard™ Mobile STEM Workstation Parts Guide

Bolt

•°

Bolts

Dowels

Base Underside (fig. 6)

End Panel Inner Side (fig. 1)

2"H Gear Guard Panel (fig. 4)

Top

Bottom

Tabletop (fig. 3)

Front

Back

Center Shelf (fig. 2)

Front

Back Rim

Front

Back

Cent

er S

helf

Dow

els

End Panel Outer Side (fig. 5)

Top

BottomFront

Back

End Panel Outer Side (fig. 5)

BottomTop

Tabl

etop

Dow

els

Gear Guard Dowels

Gear Guard Dowels

Right

Left

Back with Rim Facing Down

Front