delta networking – agema family v1 installation guide.pdfcet équipement doit être mis à terre...

Delta Networking – Agema FamilyAGC7648S V1 Aggregation Switch- AGC7648S V1- AGC7648SL V1

Installation Guide

agema.deltaww.com

iiAGC7648S V1 Aggregation Switch

Copyright

All specifications and figures are subject to change without prior notice. Actual products may look different from the photos.

All trademarks and logos mentioned in this guide are the properties of their respective holders.Copyright © Delta Electronics, Inc. All rights reserved.

Regulatory and Safety Information

This product has been tested in accordance to, and complies with the following safety standards and electromagnetic compatibility (EMC) inspection standards.

Emissions

Applicable standard

• AS/NZS CISPR 32: Class A • ICES-003 : Class A • EN55032: Class A • VCCI Class A • FCC CFR 47 Part 15, Subpart B Class A

Safety

Applicable standard

• EN 62368-1, Second Edition • UL 62368-1, Second Edition • CAN/CSA C22.2 No. 62368-1, Second Edition • IEC 62368-1, Second Edition Including All National

Immunity

Applicable standard

• EN 55024 • EN 61000-3-2: Harmonic Current Emissions • EN 61000-3-3: Voltage Fluctuations and Flicker • EN 61000-4-2: ESD • EN 61000-4-3: Radiated Immunity • EN 61000-4-4: EFT • EN 61000-4-5: Surge • EN 61000-4-6: Low Frequency Conducted Immunity • EN61000-4-8: Power Frequency magnetic field • EN61000-4-11: Voltage dips and interruption

EU RoHS Compliant

Applicable standard All AG-Series components are EU RoHS compliant

iii

Important!This product is intended for installation only in the RESTRICTED ACCESS AREA ACCESSIBLE only to SKILLED PERSONS and INSTRUCTED PERSONS with the proper authorization. • Access is through the use of a lock or tool and key, or other means of security, and is controlled by

the authority responsible for the location. • Access can only be gained by service persons or by users who have been instructed about the

reasons for the restrictions applied to the location and about any precautions that shall be taken. • Never open the equipment and/or switch the plug-in power supplies and fan tray modules. For

safety reasons, the equipment should be opened and maintenance only by qualified service personnel / SKILL PERSONS.

This product is intended for installation in Information Technology Equipment Rooms (Data Center): “Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National Electrical Code and NFPA 75.”

Important!Ce produit est conçu pour une installation dans un ENDROIT À ACCÈS RESTREINT, ACCESSIBLE uniquement par des PERSONNES COMPÉTENTES et QUALIFIÉES possédant les autorisations appropriées. • L’accès est limité par un cadenas, un outil, une clé ou par un autre moyen et est contrôlé par

l’autorité responsable des lieux. • L’accès n’est permis que pour le personnel de service ou les utilisateurs qui ont été informés sur

les raisons de la restriction imposée sur l’emplacement et sur les précautions éventuelles qui doivent être entreprises.

• N’ouvrez jamais l’équipement et ne mettez pas les modules du bloc d’alimentation et du plateau de ventilation sous tension. Pour des raisons de sécurité, l’ouverture ou l’entretien de l’équipement doit être effectué par le personnel de service ou des PERSONNES COMPÉTENTES.

Ce produit est conçu pour être installé dans les salles de la technologie de l’information (centre des données) :« Il convient à l’installation dans des salles de la technologie de l’information conformément à l’article 645 du National Electrical Code et de NFPA 75 ».

Warning: Fiber Optic Port SafetyWhen using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.

Avertissement : Consignes de sécurité concernant le port de fibre optique

Ne regardez jamais le faisceau de laser émis activé lorsque vous utilisez un port de fibre optique. Également, ne regardez jamais le port de fibre TX et les extrémités du câble du fibre directement lorsqu’ils sont activés.

ivAGC7648S V1 Aggregation Switch

CAUTIONLithium Battery CautionDanger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type. Dispose batteries according to manufacturer’s instructions.

Disposal of a BATTERY into fire or a hot oven, or mechanically crushing or cutting of a BATTERY, that can result in an EXPLOSION.

Leaving a BATTERY in an extremely high temperature surrounding environment that can result in an EXPLOSION or the leakage of flammable liquid or gas.

A BATTERY subjected to extremely low air pressure that may result in an EXPLOSION or the leakage of flammable liquid or gas.

Grounding Caution This equipment must be grounded and the power cord for product should be connected to a socket-outlet with earthing connection. Note that the grounding screw of chassis should be connected to rack instead of protective earthing conductor.

If this equipment is installed in the restricted-access location, it should have a separate protective earthing terminal on the chassis which must be permanently connected to earth ground to adequately ground the chassis and protect the operator from electrical hazards.

This equipment might provide the hazardous voltage and must be connected by qualified service or technical person, or be instructed and supervised by qualified service or technical person.

Multiple Power Sources Caution

This symbol indicates the presence of hazardous energy circuits or electric shock hazards. Refer all servicing to qualified personnel.

WARNING: Do not open the enclosure to reduce the risk of injury from electric shock hazards. Refer all maintenance, upgrades and service servicing to qualified personnel.

Caution: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

v

MISE EN GARDEMise en garde concernant la pile au lithiumRisque d’explosion si la pile est remplacée incorrectement. Remplacez-la avec une pile semblable ou de même type uniquement. Éliminez les piles selon les directives du fabricant.

L’élimination de la PILE dans un feu, un four chaud ou un broyeur mécanique peut provoquer une EXPLOSION.

L’exposition de la PILE à une température ambiante extrêmement élevée peut provoquer une EXPLOSION ou la fuite d’un liquide ou d’un gaz inflammable.

L’exposition de la PILE à une pression atmosphérique extrêmement basse peut provoquer une EXPLOSION ou la fuite d’un liquide ou d’un gaz inflammable.

Mise en garde concernant la mise en terreCet équipement doit être mis à terre et le cordon d’alimentation du produit doit être branché à une prise mise à terre. Notez que la vis de mise à la terre du châssis doit être fixée sur le bâti plutôt que sur le conducteur de protection.

Si cet équipement est installé dans un emplacement à accès restreint, l’équipement doit être doté d’une borne de mise à terre distincte sur le châssis qui doit être branchée adéquatement et en permanence afin de le mettre à terre et protéger les utilisateurs contre les dangers électriques.

Cet équipement peut générer du courant dangereux et doit être branché par du personnel technique ou de service qualifié ou par des personnes informées et supervisées par du personnel technique ou de service qualifié.

Sources multiples d’alimentation

Ce symbole indique la présence de circuits dangereux ou des risques de décharges électriques. Confiez la réparation à du personnel qualifié.

AVERTISSEMENT : N’ouvrez pas le boîtier afin de réduire les risques de blessures causées par des décharges électriques. Confiez la réparation, les mises à jour et l’entretien à du personnel qualifié.

Mise en garde : Le bouton d’alimentation et le commutateur de l’appareil ne coupent pas le courant électrique qui alimente l’appareil. L’appareil peut également être branché à plusieurs cordons d’alimentation. Afin de couper complètement le courant électrique de l’appareil, assurez-vous de débrancher tous les cordons d’alimentation de la source d’alimentation.

viAGC7648S V1 Aggregation Switch

Table of Contents

Chapter 1: Introduction -------------------------------------------------------------------1

1.1 Overview ------------------------------------------------------------------------------------ 1

1.2 Package Content ------------------------------------------------------------------------- 1

1.3 Features------------------------------------------------------------------------------------- 2

Chapter 2: Appearance and Mechanism --------------------------------------------3

2.1 Product Overview ------------------------------------------------------------------------- 3

2.2 LED Identification ------------------------------------------------------------------------- 4

2.3 System Requirements ------------------------------------------------------------------- 7

2.4 Data Center Deployment --------------------------------------------------------------- 8

2.5 Power Supply Modules ------------------------------------------------------------------ 9

2.6 Fan Tray Module -------------------------------------------------------------------------10

Chapter 3: Installation ------------------------------------------------------------------- 11

3.1 Mounting -----------------------------------------------------------------------------------11

3.2 Installing an Optional Transceiver and Cable ------------------------------------13

3.3 Connecting to the Console Port ------------------------------------------------------15

3.4 Connecting to a Power Source -------------------------------------------------------15

Chapter 4: Making the Network Connections ----------------------------------- 19

4.1 Twisted-pair Connections --------------------------------------------------------------19

4.2 Fiber Optic Connections ---------------------------------------------------------------20

4.3 Ethernet Cabling -------------------------------------------------------------------------21

Appendix 1 : Technical Specifications --------------------------------------------- 22

Appendix 2 : Warranty ------------------------------------------------------------------- 23

Limited and Support Warranty -------------------------------------------------------------23

Technical Support -----------------------------------------------------------------------------23

1

Chapter 1: Introduction

1.1 Overview

AGC7648S V1 is a ToR/Leaf and EoR switch with deep buffers for data center deployment or as mobile access/aggregation switching and edge routing in service provider network. AGC7648S V1 is not only offering 100GbE uplink ports but also supporting virtualization features. AGC7648S V1 is SDN capable, compatible with choices of third party NOS and as well as ONIE, openflow for today’s open network ecosystem. It also provides comprehensive capability on layer 2 and layer 3 features, including SNMP, Spanning Tree, VLAN, QinQ, Trunk, QoS, RIP, OSPF, IGMP, DVMRP, PIM-DM, PIM-SM, Access Control, etc. This product which aims for Data Center and Carrier Networks also supports advance features such as MPLS, TRILL, PFC, VEPA, QCN, VxLAN and NVGRE to meet Data Center high performance and virtualization requirement.

1.2 Package Content

After unpacking this switch, check the contents to be sure you have received all the components. Then, before beginning the installation, be sure you have all other necessary installation equipment.

• AGC7648S V1 series switch: AGC7648S V1 or AGC7648SL V1 *based on the SKU ordered

• Rack-mounting kits

• Installation guide

If any item is missing or damaged, contact the vendor immediately, see “Technical Support”.

2AGC7648S V1 Aggregation Switch

1.3 Features

The following lists the key main features of AGC7648S V1 switch:

• 48 x 10GbE SFP+ and 6 x 100GbE QSFP28 ports, support splitter cable

• 1 x RJ45 OOB management port

• 1 x RJ45 Console port

• 1 x USB port

• System / Fan / Power status LED indication and per port LEDs

• On board high performance CPU system with large memory

• Hot-swappable PSUs and 1+1 redundancy support

• Hot-swappable FANs and 3+1 redundancy support

• Standard 1RU chassis high

• 800Gbps interface bandwidth

• Low pin-to-pin latency: Cut-Through and Store & Forward Mode

• 4GB GDDR5 of packet buffer memory

• External TCAM for extending classification database (AGC7648S V1 only)

• Support Jumbo Frame up to 9Kbyte

• Supports port speeds of 10G, 25G, 40G, 100G

• Hardware design ready to support SyncE/IEEE1588

3

Chapter 2: Appearance and Mechanism

2.1 Product Overview

2.1.1 Front View

Management port x 1

Console port x 1

QSFP28 port x 6

SFP+ port x 48

(Figure 2-1: Front View)

2.1.2 Rear View

PSU x 1

4 Fan tray slots

Secondary PSU slot x 1 (optional)

USB port x 1

Reset x 1

(Figure 2-2: Rear View)

NOTE:The switch supports up to two PSUs. However, it might be shipped with one power supply pre-installed in the rear panel of the switch. You may purchase an additional PSU for redundancy.


2.2 LED Identification

This section provides an overview of the front and rear LEDs.

2.2.1 Front LEDs

Upper SFP+ Port LED

Lower SFP+ Port LED

Upper QSFP28 Port LED

Lower QSFP28 Port LED

Power LED

System LEDFan LED

(Figure 2-3: Front LED Identification)

LED Description

System LED

• Solid Green – Normal operation• Blinking Green – Booting progress or System in diagnostic mode• Solid Amber – System failure• Off – No power

Power LED• Solid Green – Power supply units are supplied to the switch & operating normally• Solid Amber – Power supply unit failure• Off – Power is disconnected

Fan LED• Solid Green – All fans are operating normally• Solid Amber – One or more fans failure

10G SFP+ slots

LED (Solid Lighting – Linkup; Blinking – Activity)• Solid Green – A valid 10G link• Solid Amber – A valid 1G link• Blinking –Packet transmission or reception in progress• Off – No link

• Appearance and MechanismChapter 2

5

LED Description

100G QSFP28 slots

LED1 (Solid Lighting – Linkup; Blinking – Activity)• Solid Green – 100G operation• Solid Amber – 40G operation• Solid Blue – 25G operation• Solid Purple – 10G operation• Off – No LinkLED2 (Solid Lighting – Linkup; Blinking – Activity)*• Solid Blue – 25G operation• Solid Purple – 10G operation• Off – No LinkLED3 (Solid Lighting – Linkup; Blinking – Activity)*• Solid Blue – 25G Operation• Solid Purple – 10G Operation• Off – No LinkLED4 (Solid Lighting – Linkup; Blinking – Activity)*• Solid Blue – 25G Operation• Solid Purple – 10G Operation• Off – No Link*LED2 to LED4 support through breakout cable.

Management port

Link LED

• Off – No link is established on the port• Solid Yellow – A valid link at 10/100Mbps is established on the port• Solid Green – A valid link at 1000Mbps is established on the port

Act LED• Off – No link is established on the port• Blinking Green – Activity, transmitting or receiving packet at this port


2.2.2 Rear LEDs

Fan tray LED Power Supply LED

(Figure 2-4: Rear LED Identification)

LED Description

Fan tray LED• Solid Green – FAN is operating normally• Solid Red – Fan failure

Power Supply LED

• Solid Green – PSU is operating normally• Solid Red – Unplugged or power lost; with a second PSU in parallel still with

input power


7

2.3 System Requirements

Component Requirement

System requirements

Switch fabric capacity Non-blocking full wire speed on all packet sizesForwarding architecture Store and forward or cut-through

Port packet forwarding rate (at 64 Bytes)

• 148,000,000 pps (100GbE)• 59,520,000 pps (40GbE)• 14,880,000 pps (10GbE)

Memory type• 4GB GDDR5 of packet buffer memory• External TCAM for extending classification database (AGC7648S

V1 only)Console port Serial RS232 console ports (RJ45)Management port 10/100/1000Mbps, auto sensing, auto negotiationPort requirements

Speed Capability per Port• 1G/10Gbps (SFP+ port)• 40G/100Gbps (QSFP28 port)• 10G/25G (QSFP28 port, working in breakout cable)

Full-Duplex Flow Control Support the IEEE 802.3x PAUSE frame


2.4 Data Center Deployment

The following figure illustrates the converged Ethernet data center deployment.

Spine

Leaf

Rack 1 Rack N End of Row

10GbE Fabric

100GbE Fabric

Data Center

VPN/MPLS

VPN/MPLS

VPN/MPLS

Data Center

Internet

Internet

(Figure 2-5: Data Center: Spine and Leaf Deployment)

BBU

BBU

BBU

Mobile AccessNetwork

AGC7648S V1 Access Switch

10GbE

10GbE

10 GbE

Service Provider Core

Access Packet Switch Network

AGC7648S V1Aggrega�on Switch Provide Edge Router Provide Edge Router

AGC7648S V1Aggrega�on Switch

(Figure 2-6: Mobile Access Network Deployment)


9

2.5 Power Supply Modules

The power supply modules are hot-swappable power supply units (PSUs) for the switch.You can install up to two PSUs. The PSUs operate in a load-sharing mode and provides 1+1 redundancy.

(Figure 2-7: Power Supply Unit)

NOTE:1+1 redundancy is a system where a switch power supply is backed up by another switch power supply in a load-sharing mode. If one power supply fails, the other power supply takes over the full load of the switch.

WARNING:• The switch includes plug-in power supply and fan tray modules that are

installed into its chassis. All modules have a front-to-back airflow direction.• Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.• Remove the power cable from the module prior to removing the module

itself. Power cable must not be connected prior to insertion in the chassis or equivalent.

AVERTISSEMENT:• Le commutateur comporte des modules de bloc d’alimentation enfichable

et de cassette de ventilation dans son châssis. La circulation d’air se fait de l’avant vers l’arrière dans tous les modules.

• Risque d’explosion si la pile est remplacée par une de type différent. Suivez les instructions pour éliminer les piles usées.

• Débranchez le câble d’alimentation du module avant de retirer ce dernier. Le câble d’alimentation ne doit pas être branché avant l’insertion des modules dans le châssis ou ailleurs.


2.6 Fan Tray Module

The fan tray module is part of the switch air cooling system that provides cooling for theswitch. You must install the fan tray module in the switch that matches the airflow directionof the installed power supply unit.

(Figure 2-8: Fan Tray Module)

11

Chapter 3: Installation

3.1 Mounting

This switch can be mounted in a standard 19-inch equipment rack. Prior rack mounting the switch, pay particular attention to the following factors: • Mechanical Loading: Do not place any equipment on top of a rack-mounted unit. • Circuit Overloading: Be sure that the supply circuit to the rack assembly is not overloaded. • Grounding: Rack-mounted equipment should be properly grounded. Particular attention

should be given to supply connections other than direct connections to the mains.

To rack-mount devices:

1. Install the front mounting bracket to the device using the four M4 screws provided in the rack mounting kit.

Repeat step 1 to assemble another bracket.

(Figure 3-1: Installing the Front Mounting Bracket)

2. Align the front mounting bracket to the rack holes. Then secure the front mounting bracket to the rack by using two M6 screws.

Repeat step 2 to fasten another front bracket.

NOTE:Rack screws and clip nuts are not supplied in the rack-mounting kit.

CAUTION:Due to the switch’s weight, it should be installed by at least two people.MISE EN GARDE:À cause du poids du commutateur, au moins deux personnes doivent l’installer.


(Figure 3-2: Securing the Front Mounting Bracket)

3. From the rear side of the device, install the rear mounting brackets on both sides of the device.

(Figure 3-3: Installing the Rear Mounting Brackets)

4. Align the rear mounting brackets to the rack holes. Then secure the rear mounting brackets to the rack by using two M6 screws.Repeat step 4 to fasten another rear bracket.

(Figure 3-4: Securing the Rear Mounting Brackets)

5. If installing a single switch only, go to “Connecting to a Power Source”.6. If installing multiple switches, mount them in the rack, one below the other, in any order.

• InstallationChapter 3

13

3.2 Installing an Optional Transceiver and Cable

The SFP+ slots support the following optional transceivers and cables:

• 10GBASE-SR • 10GBASE-LR

• 10GBASE AOC • 10GBASE DAC

The QSFP28 slots support the following optional transceivers and cables:

• 100G BASE-SR4 • 100G BASE-LR4

• 100G AOC (Active Optical Cable) • 100G DAC (Direct Attached Cable)

• 100G to 4x25G AOC • 100G to 4x25G DAC

• 40G BASE-SR • 40G BASE-LR4

• 40G AOC (Active Optical Cable) • 40 DAC (Direct Attached Cable)

(Figure 3-5: Inserting an SFP+ Transceiver into a Slot)

(Figure 3-6: Inserting a QSFP28 or QSFP Transceiver into a Slot)

To install the SFP+, QSFP, or QSFP28 transceiver, follow these steps:1. Consider network and cabling requirements to select an appropriate SFP+, QSFP, or

QSFP28 transceiver type.2. Insert the transceiver with the optical connector facing outward and the slot connector

facing down. Note that SFP+, QSFP, or QSFP28 transceivers are keyed so they can only be installed in one orientation.

3. Slide the SFP+, QSFP, or QSFP28 transceiver into the slot until it clicks into place.


NOTE: • SFP+, QSFP, or QSFP28 transceivers are hot-swappable. The switch does

not need to be powered off before installing or removing a transceiver. However, always first disconnect the network cable before removing a transceiver.

• SFP+, QSFP, or QSFP28 transceivers are not provided in the switch package.


15

3.3 Connecting to the Console Port

This port is used to connect a console device to the switch through a nullmodem serial cable. The console device can be a PC or workstation running a VT-100 terminal emulator, or a VT- 100 terminal.

NOTE:An RJ-45-to-DB-9 cable is not supplied with the switch for connecting to a PC’s RS-232 serial DB-9 DTE port.

DB-9 port

RJ-45 connector

(Figure 3-7: Console Port Connection)

3.4 Connecting to a Power Source

3.4.1 Installing an AC Power SupplyTo connect a switch to a power source:

1. Insert the power cable plug directly into the AC socket of a PSU located at the back of the switch. Power socket

(Figure 3-8: Power Socket)

2. Plug the other end of the cable into a grounded, 3-pin, AC power source.

NOTE:For International use, you may need to change the AC line cord. You must use a line cord set that has been approved for the socket type in your country.


3. Check the PSU and front-panel LEDs as the device is powered on to be sure that AC power is being received and the Power LED is on. If not, check that the power cable is correctly plugged in.

4. Repeat steps 1 and 2 when a second PSU module is installed.Two installed PSU modules operate in a load-sharing mode and provide 1+1 redundancy.

3.4.2 Installing a DC Power SupplyTwo types of connection to a power source:

a. DC power cord for DC source connection

1. Insert the power cable plug directly into the DC socket of a PSU located at the back of the switch. The earthing wire of the protective earthing conductor shall be green-and-yellow, 14AWG. The terminals for connecting protective earthing conductors shall comply with conductor size 2.5 (mm2), nominal thread diameter screw type 4 (mm). Considered current rating of protective device before DC input: 20A. The ground symbol on the outside of the case is for functional grounding only.

GND

-48V(-DC)-48V_RTN (+DC)

(Figure 3-9: Installing a DC Power Supply and Power Cable)

2. Plug the other end of the cable into DC power source. This product is intended to be supplied by DC power source with rated -48 ~ -60Vdc, 20A minimum, Tma = 45 degree C, and the altitude of operation = 3048 m. The power cable should be 14AWG (20A minimum, -48V minimum).

CAUTION: • Reversing polarity when connecting DC power wires can

permanently damage the power supply or the system. • Always disconnect the power cable from power source before you

service the power supply slots.MISE EN GARDE:

• L’inversion de la polarité des câbles d’alimentation CC lors de leur branchement peut endommager irréversiblement le bloc d’alimentation ou le système.

• Débranchez le câble d’alimentation de l’unité d’alimentation avant l’entretien des fentes du bloc d’alimentation.


17

3. Check the PSU and front-panel LEDs as the device is powered on to be sure that DC power is being received and the Power LED is on. If not, check that the power cable is correctly plugged in.

4. Repeat steps 1 and 2 when a second PSU module is installed.Two installed PSU modules operate in a load-sharing mode and provide 1+1 redundancy. The above description for equipment installation reference only.

b. Adapter connector for DC source connection

1. Attach the connector directly into the DC socket of a PSU located at the back of the switch. The earthing wire of the protective earthing conductor shall be green-and-yellow, 14AWG. The terminals for connecting protective earthing conductors shall comply with conductor size 2.5 (mm2), nominal thread diameter screw type 4 (mm). Considered current rating of protective device before DC input: 20A. The ground symbol on the outside of the case is for functional grounding only.

GND-48V(-DC)

-48V_RTN (+DC)

(Figure 3-10: Assembling a DC Connector and Power Wires)

2. Plug the other end of power wires into DC power source. This product is intended to be supplied by DC power source with rated -48 ~ -60Vdc, 20A minimum, Tma = 45 degree C, and the altitude of operation = 3048 m. The power cable should be 14AWG (20A minimum, -48V minimum).

CAUTION: • Reversing polarity when connecting DC power wires can

permanently damage the power supply or the system. • Always disconnect the power cable from power source before you

service the power supply slots.MISE EN GARDE:

• L’inversion de la polarité des câbles d’alimentation CC lors de leur branchement peut endommager irréversiblement le bloc d’alimentation ou le système.

• Débranchez le câble d’alimentation de l’unité d’alimentation avant l’entretien des fentes du bloc d’alimentation.

3. Check the PSU and front-panel LEDs as the device is powered on to be sure that DC power is being received and the Power LED is on. If not, check that the power cable is correctly plugged in.


4. Repeat steps 1 and 2 when a second PSU module is installed.

Two installed PSU modules operate in a load-sharing mode and provide 1+1 redundancy. The above description for equipment installation reference only.

19

Chapter 4: Making the Network Connections

The AGC7648S V1 switch is designed to provide high-speed, lossless Ethernet connections between server racks through its 10G SFP+ or 100G QSFP28 ports. This chapter describes how to make network connections to the switch.

4.1 Twisted-pair Connections

The switch’s Management port connection requires an unshielded twisted-pair (UTP) cable with RJ-45 connectors at both ends. Use Category 5, 5e or 6 cable for 1000BASE-T connections, Category 5 or better for 100BASE-TX connections, and Category 3 or better for 10BASE-T connections.

4.1.1 Cabling Guidelines

The RJ-45 port on the switch supports an automatic MDI/MDI-X pinout configuration, so you can use a standard straight-through twisted-pair cable to connect to any other network device (PCs, servers, switches, routers, or hubs).

4.1.2 Connecting to the Management Port

1. Attach one end of a twisted-pair cable segment to the link device’s RJ-45 connector.

RJ-45 connector

(Figure 4-1: Making a Connection to the Management Port)

2. Attach the other end to the Management port on the switch.

Make sure the twisted pair cable does not exceed 100 meters (328 ft) in length.

3. When the connection is made, the Mgmt LED (on the switch) will light green to indicate that the connection is valid.


4.2 Fiber Optic Connections

Optional 10G SFP+ or 100G QSFP28 transceivers can be used for fiber connections from the switch to other network devices in the data center. An SFP+ or QSFP28 transceiver may also be used for long distance connections to devices at another site.

WARNING:

• This switch uses lasers to transmit signals over fiber optic cable. The lasers are compliant with the requirements of a Class 1 Laser Product and are inherently eye safe in normal operation. However, you should never look directly at a transmit port when it is powered on.

• When selecting a fiber SFP+ or QSFP28 device, considering safety, please make sure that it can function at a temperature that is not less than the recommended maximum operational temperature of the product. You must also use an approved Laser Class 1 SFP+ or QSFP28 transceiver.

AVERTISSEMENT:

• Ce commutateur utilise du laser pour émettre des signaux à travers le câble de fibre optique. Le laser est conforme aux exigences des produits de laser de classe 1 et, par conséquent, il est sécuritaire pour les yeux dans des conditions normales de fonctionnement. Toutefois, vous ne devez jamais regarder directement un port d’émission lorsqu’il est activé.

• Pour des raisons de sécurité lors de la sélection d’un appareil avec la fibre SFP+ ou QSFP28, veuillez vous assurer qu’il peut fonctionner à une température qui n’est pas plus basse que la température de fonctionnement maximale recommandée pour le produit. Vous devez également utiliser un émetteur-récepteur SFP+ ou QSFP28 homologué de classe 1.

The following figure illustrates the SFP+ or QSFP28 port fiber connection.

(Figure 4-2: Making SFP+ Port Fiber Connection)

• Making the Network ConnectionsChapter 4

21

(Figure 4-3: Making QSFP28 Port Fiber Connection)

4.3 Ethernet Cabling

To ensure proper operation when installing the switch into a network, make sure that the current cables are suitable for 10BASE-T, 100BASE-TX or 1000BASE-T operation. Check the following criteria against the current installation of your network: • Cable type: Unshielded twisted pair (UTP) or shielded twisted pair (STP) cables with RJ-

45 connectors; Category 3 or better for 10BASE-T, Category 5 or better for 100BASE-TX, and Category 5, 5e or 6 for 1000BASE-T.

• Protection from radio frequency interference emissions • Electrical surge suppression • Separation of electrical wires (switch related or other) and electromagnetic fields from

data based network wiring • Safe connections with no damaged cables, connectors or shields


Appendix 1 : Technical Specifications

Item Description

Key components

Switch controller BCM88375 x 1PHY BCM5461S x 1CPU Intel Broadwell-DE D1527 Quad CoreFlash ROM 32 MB SPI FlashSystem memory 16GB DDR4 SO-DIMM x 2Storage 128GB m.2. SSDBMC AST2520Packet buffer 4GB GDDR5

TCAM • AGC7648S V1: NL88659 x 2 • AGC7648SL V1: N/A

SyncE/1588 IDT 82P33910Network Protocol and Standards Compatibility

Network protocol/compatibility

• IEEE 802.3 10Base-T on console port • IEEE 802.3u 100Base-TX on console port • IEEE 802.3ab 1000BASE-T on console port • IEEE 802.3x Flow-Control • IEEE 802.3z 1000BASE-X • IEEE 802.3ae 10Gb/s Ethernet • IEEE 802.3ba: 40Gb/s Ethernet

Interface Information

Interface

• Small Form-factor Pluggable Plus (SFP+) slot x 48 • Quad Small Form-factor Pluggable 28 (QSFP28) slot x 6 • 10/100/1000Mbps console Management port x 1 • External Console port (RJ45) x 1 • USB port x 1

Power Supply Unit

Type AC-in PSU DC-in PSUMax. output power 850W 800WInput voltage AC 100 ~ 240V DC -48 ~ -60VOutput voltage DC 12V DC 12VPhysical

Dimensions (W x D x H) 438.5 x 550 x 43 mm (17.26 x 21.65 x 1.69 inches)Weight 10 kg (22.05 lbs)Environmental Specifications

Operating temperature 0 to 45°CStorage temperature -20 to 70°COperating humidity 10 to 90% RHStorage humidity 5 to 95% RH

23

Appendix 2 : Warranty

Limited and Support WarrantyThree Years End-User Guarantee.

The new product you purchased from Delta or Delta authorized resellers (“Resellers”) will be free from defects in materials, workmanship, and design affecting normal use, for a period of three (3) years from the original purchase date. This warranty does not include accessories or any free bundled sales items which may have been delivered along with the product. The original purchasing invoice and the serial number on your product are both required when you request for any warranty service.

During the warranty period, products for which proper claims are made will, at Delta’s option, be repaired or replaced at Delta’s expense. Customers may contact Delta’s technical support for warranty services, which may be provided either through Resellers or by Delta directly. Delta owns all parts removed from the repaired products. Delta will use new or reconditioned parts made by various manufacturers to perform repairs and/or to build replacement products. All replaced or repaired products will be warranted for the remainder of the original warranty period or thirty (30) days, whichever is longer.

Unless otherwise having a separate service level agreement (SLA) with Delta, you may only have any in-warranty product returned to Delta for repair or replacement in a normal turnaround time which differs according to geographic areas.

EXCLUSIONS

This Guarantee does not apply to defects resulting from: improper or inadequate installation, use, or maintenance; actions or modifications by unauthorized third parties or the end user; accidental or willful damage; or normal wear and tear.

Technical Support • For software related technical support and product return policy, please contact your software

providers. • For hardware related technical support, please send your e-mail to

[email protected]. • Please note that hardware related issues are limited to the following situations:

• System Self-Diagnostic Test Failure • Product is physically damaged on arrival

• Missing items in the package (see “Package Content”) • The product does not power on • Fan failure


Return Policy

Any product returned to Delta or Resellers without prior Return Material Authorization (RMA) from Delta will be considered an unauthorized return, and you will not receive any repair or replacement for the product and Delta will not ship the product back to you. The authorization will be provided through the e-mail: [email protected]. For in-warranty defective product return, you shall be responsible for proper packaging and Delta will not take responsibility for any shipping damage due to your improper product packaging.

Disclaimer

EXCEPT FOR THE WARRANTIES EXPRESSLY SET FORTH IN THIS “LIMITED AND SUPPORT WARRANTY”, DELTA MAKES NO OTHER WARRANTIES REGARDING THE PRODUCT, ANY PARTS INCORPORATED THEREIN OR ANY SERVICES PROVIDED THEREWITH AND HEREBY DISCLAIMS ANY AND ALL SUCH OTHER WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, WHICH ARE ALL HEREBY EXCLUDED.

delta networking – agema family v1 installation guide.pdfcet équipement doit être mis à terre...

Documents