deicing control facilities improvements-2016 project … · deicing control facilities...
TRANSCRIPT
Deicing Control Facilities Improvements-2016
Project No. I-16-023
Indianapolis Airport Authority
Submittal Review Sheet
Attached is the submittal for specification section 42 2139 Submersible Liquid Pumps for the Deicing
Control Facilities Improvements – 2016 I-16-023 project for your review and approval. Thieneman
Construction has reviewed the submittal information and added the following notes for your review,
approval, and consideration
Items for Engineer:
1. KSB Submersible Sewage Pump
Items for Supplier: 1. Supply materials as requested by TCI in conformance with the project schedule.
If you have any questions on this submittal information, please contact Lori Kelleher at 317-763-1634. Thieneman
Construction requests your review, approval, and return of one (1) copy of the approved submittals
Project Name: Deicing Control Facilities Improvements-2016
Contractor: Thieneman Construction, Inc.
Subcontractor / Supplier: Straeffer Pump and Supply
Submittal Number: 000009
Submittal Specification Section: 42 2139 Submersible Liquid End Pumps Item
1.4.A.2 Product Data and
Item 1.4.A.3 Shop Drawings
Item Description: Submersible Liquid Pumps
Quantity of Submittals: 1 – Electronic
Comments: See Above
Quantity of Approved Submittals to be Returned: 1 – Electronic
Signature:
CONTRACTOR’S CERTIFICATION Submittal material has been reviewed for compliance with specifications and drawings. Required field measurements have been verified. The work shown on this submittal has been coordinated with other submittals affected by this work. All data has been checked by the Contractor and any variations from the specifications or drawings have been noted. The work described on the submittal material is recommended by the Contractor, and the guarantee in the specifications will apply:
Contractor: Thieneman Construction
Approved: Lori Kelleher
Date: 10/12/2016
STRAEFFER PUMP & SUPPLY, INC.
Since 1967
8055 State Road 62 W
P.O. Box 99
Chandler, IN 47610
800.837.7867
www.straefferpump.com
1
GENERAL COMMENTS & NOTES FOR DEICING CONTROL FACILITIES SUBMERSIBLE LIQUID PUMP IMPROVEMENTS INDIANAPOLIS, INDIANA STRAEFFER JOB #16-098W 1. We propose to furnish one (1), Model KRT K 250-401/A806UNG-K, explosion proof, 90
HP, solids handling pumps as manufactured by KSB. KSB has been actively manufacturing equipment for over 140 years. Certified performance curve will be provided for the pump.
2. The pump will be provided with a K type impeller, trimmed to the duty point. The pump
will be furnished with: cooling jacket, double mechanical seals composed of 2 separate lapped faces (carbon vs. silicon carbide upper and silicon carbide vs. silicon carbide lower); seal leak moisture detection which, if activated, will light a pilot light in the control panel; heat sensor in the motor to stop motor if winding temperature overheats; and all exposed nuts and bolts will be stainless steel. The pumps will be furnished with bearings that have a B10 minimum bearing life per section 43 2139 - Part 2.2 - R-1. Spare parts will be supplied as specified.
3. KSB’s standard 7 year warranty is included herein. 4. The pump will be provided with 150' cord lengths. These cords cannot be spliced as it
voids warranty. Straeffer Pump and Supply will not assume the responsibility of proper cord length. Please carefully check this matter and advise if this is insufficient to reach the termination point.
5. Our company is an authorized repair station for all KSB environmental pumps. 6. We assume the supply voltage is 3/460, if not please advise. Straeffer Pump and
Supply will not be responsible for improper voltage feed to the job site. Please carefully check the voltage feed to the lift station and advise if this is incorrect.
7. To the best of our knowledge we either meet or exceed the specified equipment. However,
if questions arise, please do not hesitate to contact Mark Wahl ([email protected]) for mechanical questions or Stewart May ([email protected]) for electrical questions.....(800)837-PUMP.
PUMP SUBMITTAL REQUIREMENTS
PUMP AND MOTOR DATA PUMP #1
PUMP MODEL KRT K 250-401/A806UNG-K
MOTOR HORSE POWER 90
MOTOR RPM 1160
VOLTAGE, PHASE, & CYCLE 460/3/60
POWER CABLE LENGTH 150’
PERFORMANCE CHARACTERISTICS 3100 GPM @ 78’ TDH
IMPELLER DIAMETER 15.67”
IMPELLER TYPE multi-vane, cast iron
DISCHARGE SIZE
PUMP WEIGHT 2937 lbs.
MOISTURE SENSOR REQUIRED YES
HEAT SENSOR REQUIRED YES
UL CLASS 1 GROUP D REQUIRED YES
TYPE OF STATION Simplex
PROJECT NAME: Deicing Control Facilities Improvements
LOCATION: Indianapolis, Indiana STATION NO.
Section 43 21 39 – Pump UGSP-4
OWNER: City of Indianapolis ENGINEER:
Gresham Smith and Partners
PREPARED BY: DATE SUBMITTED:
MXW
Data sheet
Customer item no.:Communication dated: 11/08/2016 Number: 4002826961
Doc. no.: Indianapolis Airport Item no.: 100
Quantity: 1 Date: 12/08/2016
Page: 1 / 5
KRTK 250-401/A806UNG-K Version no.: 3
Operating data
Design
Driver, accessories
Requested flow rate 3100.00 US GPM
Requested developed head 78.00 ft
Pumped medium Wastewater, municipalmechanically treatedNot containing chemical andmechanical substances whichaffect the materials
Ambient air temperature 68.0 °F
Fluid temperature 68.0 °F
Fluid density 62.428000 lb/ft³
Actual flow rate 3100.00 US GPM
Actual developed head 78.00 ft
Efficiency 78.2 %
Power absorbed 77.88 HP
Pump speed of rotation 1183 rpm
Max. power on curve 85.52 HP
Shutoff head 118.18 ft
Design Single system 1 x 100 %
Fluid viscosity 0.0015 in²/s Performance test Yes
Design Close-coupled submersibleOrientation VerticalSuction flange pumpaccording to(DN1)
unmachined
Discharge flange pumpaccording to(DN2)
EN 1092-2 / DN 250 / PN 10
Shaft seal 2 mech. seals in tandemarrangement with oil reservoir
Manufacturer KSBType MGMaterial code SIC/SIC/NBR
Impeller type Multivane radial flow impeller(K)
Wear ring Casing/impeller wear ringImpeller diameter 15.67 in
Free passage size 4.13 in
Direction of rotation fromdrive
Clockwise
Temperature sensor PT100inboard
With
Color Ultramarine blue (RAL 5002)KSB-blue
Driver type Electric motorModel (make) KSBMotor const. type KSB Sub. motorNEMA code letter GFrequency 60 Hz
Rated voltage 460 V
Rated power P2 90.00 HP
Rated current 106.0 A
Starting current ratio 6.4
Insulation class H according IEC 34-1Motor enclosure IP68Cos phi at 4/4 load 0.87
Motor efficiency at 4/4 load 91.0 %
Motor service factor 1.15
Temperature sensor PTC resistorMotor winding 460 V
Number of poles 6
Starting mode Direct-on-line startingConnection mode DeltaMotor cooling method closed-circuit jacket coolingMotor cooling jacket WithMotor version UCable design Rubber hoseCable entry Sealed along entire lengthPower cable AWG 5-4Number of power cables 2
Control cable AWG 15-10Number of control cables 1
Moisture sensor With
Cable length 150.00 ft
Data sheet
Customer item no.:Communication dated: 11/08/2016 Number: 4002826961
Doc. no.: Indianapolis Airport Item no.: 100
Quantity: 1 Date: 12/08/2016
Page: 2 / 5
KRTK 250-401/A806UNG-K Version no.: 3
Materials G
Packaging
Outdoor storage at -40°C to +50°C for up to 3 months. Packetmust be covered. No corrosion protection, only transportprotection.
Nameplates
Certifications
Installation parts
Pump casing (101) Cast iron A 48 Class 35 BDischarge cover (163) Cast iron A 48 Class 35 BShaft (210) Chrome steel A 276 Type 410
TImpeller (230) Cast iron A 48 Class 35 BBearing bracket (330) Cast iron A 48 Class 35 BO-Ring (412) Nitrile rubber NBRCasing wear ring (502.1) Cast iron A 48 Class 35 B
Impeller wear ring (503) Wear resistant duplexstainless steel
Shaft protecting sleeve (524) Chrome steel A 276 Type 410T
Cooling jacket (66-2) Stainless steel A 276 Type316 Ti
Motor housing (811) Cast iron A 48 Class 35 BMotor cable (824) Chloroprene rubberScrew (900) Stainless steel A 193 B8M
Packaging category B1 Wooden or plywoodcase, cover provided withpolyproylene cellular sheet,outdoor storage up to 3months
Packaging for transport ShipIPPC Standard ISPM 15 Yes
Packaging for storage Indoor
Nameplates language International Duplicate nameplate With
Hydraulic performance testAcceptance standard Hydraulic Inst. AQuantity meas. points Q-H 7Certificate Inspection cert. 3.1 to EN
10204
Test participation Non-witnessedQuantity, non-witnessed 1Quantity, witnessed 0
Scope of supply Pump without installationparts
Performance curve
Customer item no.:Communication dated: 11/08/2016 Number: 4002826961
Doc. no.: Indianapolis Airport Item no.:100
Quantity: 1 Date: 12/08/2016
Page: 3 / 5
KRTK 250-401/A806UNG-K Version no.: 3
0 1000 2000 3000 4000 5000 6000[US GPM]
0
50
100
[ft]
Qmin
To
tal
de
ve
lop
ed
he
ad
0 1000 2000 3000 4000 5000 6000[US GPM]
5
35
20
[ft]
NP
SH
req
.
0 1000 2000 3000 4000 5000 6000[US GPM]
0
50
[%] Eff
icie
nc
y
0 1000 2000 3000 4000 5000 6000[US GPM]
60
80
[HP]
Po
wer
Inp
ut
Flow
Curve data
Speed of rotation 1183 rpm
Fluid density 62.428000 lb/ft³
Viscosity 0.0015 in²/s
Flow rate 3100.00 US GPM
Requested flow rate 3100.00 US GPM
Total developed head 78.00 ft
Requested developed head 78.00 ft
Efficiency 78.2 %
Power absorbed 77.88 HP
NPSH req. 3% 13.58 ft
Curve number K42586sEffective impeller diameter 15.67 in
Acceptance standard Hydraulic Inst. A
Installation plan
Customer item no.:Communication dated: 11/08/2016 Number: 4002826961
Doc. no.: Indianapolis Airport Item no.:100
Quantity: 1 Date: 12/08/2016
Page: 4 / 5
KRTK 250-401/A806UNG-K Version no.: 3
15.75
6.69
DN1
min
23.62
1)
Minimum water level t1
ø0.98
62.01
11.02
9.84
3.94
min
1)
71.06
15.75
DN3
27.56
79.92
20.87
8.86
5.31
16.54
ø 3.5
5.91
28.94
51.18
35.43min
0.71ø
7.28
3.94
16.73
38.98
27.17
Access opening
54.13
45.87
(Lifting bail optional)
Drawing is not to scale Dimensions in in
Installation plan
Customer item no.:Communication dated: 11/08/2016 Number: 4002826961
Doc. no.: Indianapolis Airport Item no.:100
Quantity: 1 Date: 12/08/2016
Page: 5 / 5
KRTK 250-401/A806UNG-K Version no.: 3
Motor Connections
Weight net
Connect pipes without stress or strain!Dimensional tolerances for shaft axis height: DIN 747Dimensions without tolerances, middle tolerances to: ISO 2768-mConnection dimensions for pumps: EN735Dimensions without tolerances - welded parts: ISO 13920-BDimensions without tolerances - gray cast iron parts: ISO 8062-CT9
For auxiliary connections seeseparate drawing.
Motor manufacturer KSBMotor size A80NMotor power 90.00 HPNumber of poles 6Speed of rotation 1181 rpm
Suction flange pumpaccording to(DN1)
unmachined
Discharge flange pumpaccording to(DN2)
EN 1092-2 / DN 250 / PN10
Pump, Motor, Cable 2937 lbmTotal 2937 lbm
0
20
40
60
80
100
120
140
160
200
P2[hp]
0
20
40
60
80
100
120
140
160
200
I[A]
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
1.0
etacos
0.0 20.0 40.0 60.0 80.0
P1 [kW]
1200
1190
1180
1170
n [rpm]
eta
P2
cos
I
Motor dataAmarex KRT - Installation types: K/D
Motor type : : A806UNGMaterial version : G [cast iron] also for motors -G1,-G2,-GH,-H
Nominal voltage : 460 [V]Frequency : 60 [Hz]Rated power : 90.0 [hp]Service factor : 1.15Rated current : 106 [A]Nominal Speed : 1181 [rpm]NEMA code letter : G Starting/full load current : 6.4 Max. water temperature : 104 [°F]Max. air temperature at the cable : 104 [°F]
Maximum 10 starts per hour starting mode: direct
Cable norm/ Cable selection according to: NEC
2 Cables AWG 5-4 [4G16] Ø 0.89-0.94 in1 Control cable AWG 15-10 [10G1.5] Ø 0.63-0.67 in
Descriptions : P1 [kW]........ electric power P2 [hp]........ mechanical power eta [%]........ Efficiency cos phi........ Power factor I [A].......... Current n [rpm]........ Speed
Load 4/4 3/4 2/4 1/4
n [rpm] P1 [kW] P2 [hp] eta [%] cos phi I [A] 1181 73.8 90.0 91.0 0.87 106 1186 55.2 67.5 91.2 0.83 83 1191 37.3 45.0 90.0 0.73 64 1195 20.0 22.5 83.8 0.52 48
Tolerances of the electrical parameters according to IEC 60034-1.
User: habefradate: 2016-08-12© 2000-2003 by KSB AG / Author: Dobbertin, Frank
02 Features
Three (3) 161 hp Dry-Pit Pumps with cooling jacket
KRT Submersible Motor Pumps for Versatile Applications
Advantages and technical features:
• economical installation
• wet installation submersible motor pumps operate submerged in
the pump sump
• low building costs, eliminating intermediate shaft, drainage
pump and superstructure
• pump stations below ground do not spoil the landscape, traffic
areas remain unchanged when sumps are located under roads
• the compact pump/motor sets require less space and are easier
to install
• with the double pump guides the pump can be installed at any
installation depth and withdrawn without difficulties
• no need to enter the pump sump to carry out inspection and
maintenance work
• smaller inspection opening on duplex pump stations
• small pump sump due to high permissible switching frequency
• stationary and portable applications possible, see types of
installations
• permanent dry well installation possible where the pump is
exposed to the danger of occasional flooding
• minimum assembly and maintenance work
• no coupling to be aligned since KRT pump and motor have a
common shaft
• no sealing or flushing water required or leakage outlet
• motor cooled by the medium
• high operation safety (dry running possible)
• quiet operation
KRT submersible motor pumps are highly efficient in
the handling of:
- raw sewage containing solid and long fibrous mixtures
- contaminated liquids with a high gas and air content
- liquids containing sludge and solid substances
- floating sludge and debris such as vegetable wastes,
wood chips and similar waste (KRT as a vacuum
suction pump on a pontoon)
- dirty water and storm water
- raw, digested and activated sludge
- flume and wash water
- pulp
- slaughter house wastes
- water/product suspensions
- sand/cement/water mixtures
- plastic granules in liquid
- textile effluent
- industrial effluent and wash water as well as media in
production plants, e.g. flume water, scale wastes,
cutting oil and other media containing abrasive
components.
- chemical and waste disposal effluent with pH-values
2 to 12
- effluent containing acid
- seawater and brackish water as well as other media
with chlorine.
Type of construction:
KRT submersible motor pumps are submerged, single
stage close-coupled pump sets. Depending on the liquid
to be pumped and the size of the pump different impel-
ler shapes are used:
K - Closed non-clogging 2 or 3 vane impeller
E - Single vane impeller
F - Vortex impeller
S - Grinding impeller
D - Open single vane impeller
Fields of application:
Two (2) 148 hp Submersible Pumps with cooling jacket.
04 Features
Impeller Type Description
S - Grinder impeller for high pressure domestic sewage systems containing long fibrous admixtures
- effluents - domestic sewage
F - Vortex impeller for liquids with coarse solids and media containing air and gas
- raw sewage - raw and digested sludge
E - Single vane impeller for media with solid and long fibrous materials
- raw sewage - raw sludge - recirculation and heating sludge
K - Closed non-clogging 2 or 3 vane impel-ler for contaminated solids-laden liquids
- raw sewage - effluent - activated sludge
D - Open single vane impeller for handling fibrous solids and heavy sludge (up to 13% solids by weight)
- raw sewage - raw and digested sludge - activated sludge - recirculation and heating sludge
The right impeller design for cost effective and reliable operation
Since no one type of impeller is equally suitable for all applica-
tions, KSB offers the KRT series of submersible motor pump with
various types of impellers according to specific requirements. Our
range of vortex, single vane and non-clogging impellers allows the
best impeller to be selected for the product with due consideration
of operating parameters such as flow rate, head, efficiency, solid
size, wear behavior and gas content.
Flexible installations
Stationary guide cableinstallation
Stationary guide railinstallation
Portableinstallation
Dryinstallation
Stationary guide cable or guide rail installation - for installation in the pump sump with suspension device ensuring automatic pressure-tight coupling of the pump.
Portable installation - with base stand and flange connection for pipework or hose connection (e.g. with rigid coupling).
Dry installation - for installation in a separate dry well.
05
The Pump That Keeps Cool
1 - Cable Entry - absolutely water tight. Even in the event of damage to the cable sheath and core insulation there is no possibility of moisture entering the motor chamber along the strands due to capillary action.
2 - Thermal Motor Protection - extensive sensor technology for permanent monitoring to ensure trouble-free operation.
3 - High Efficiency Motor - all motors FM approved for Class I, Division 1 Group C & D hazardous locations.
4 - OPTIONAL Closed-loop Cooling System - optimal cooling in all operating conditions with no external cooling required, perfect for dry-well installations .
5 - Non-proprietary silicon carbide faced mechanical seals mounted in tandem in collant liquid bath.
6 - Major Casting of ASTM A 48 Class 35 B Cast iron, Duplex Stainless steel and wear resistant Chromium White Iron.
7 - Heat exchanger and separate coolant circulating impeller for optional cooling jacket.
8 - Enclosed 1, 2 and 3 vane or recessed impellers available to allow a hydraulic selection ideally suited for a particular application.
9 - Wear rings in hard metal to insure continued high efficiences and long impeller life.
10 - Pump and motor shafts of stainless steel or Gr 1045 carbon steel protected and isolated by stainless steel shaft sleeves (only for carbon steel shafts).
11 - Temperature monitoring standard for lower bearing, optional for upper bearing.
12 - Float sensor in separate leakage collection chamber. Prevents leakage from reaching motor or lower bearing.
* Motors larger than ~80 hp:• 1
• 2
• 3
• 4
• 6 • 8 • 9
10 •
11 •
12 • • 5
• 7
* For certain models, 30, 40, 50, 56, and 74 HP motors with cooling jacket are also available.
06 Installations and Technical Data
Three (3) 12“ discharge, 161 hp closed-loop cooling dry-pit pumps with stainless steel Jacket in existing pumping station.
Dry Well Installations
Two (2) large 24“ discharge, 148 hp Submersible Pumps with stainless steel cooling jacket on KSB guide rail system for an effluent waste water treatment pumping station.
Wet Well Installations
Three (3) 10“ discharge, 194 hp closed-loop cooling dry-pit pumps with stainless steel Jacket in existing pumping station.
Two (2) large 24“ discharge, 251 hp Submersible Pumps and one (1) 12“ discharge, 80 hp on KSB guide cable system for a stormwater station.
07
Technical Data
Operating Data
Pump Size - DN 2” - 30”
Capacity - Q (gpm) up to 45,000
Head - H (ft) up to 330
Liquid Temperature - t (°F) up to 140
Motor Rating - P (hp) up to 1,140
Material Options Cast Iron A 48 Class 35 B
Wear Resistant Chromium White IronA 532 II C 15% CrMo-Hc
Duplex Stainless SteelA 743 CD 4 MCU
Part Designation G G1 G2 GH H C1 C2
Pump Casing A 48 Class 35 B A532 II C 15% CrMo-Hc A 890 CD 4 MCU
Intermediate Casing
A 48 Class 35 B A 532 II C 15% CrMo-Hc A 890 CD 4 MCU
Shaft A 276 Type 420;A 576 Gr. 1045 w/shaft protection sleeve
A 182F51/A276 Type 420/ A576 Gr. 1045
Impeller A 48 class 35 B
A 743 CD 4 MCU
A 532 II C 15% CrMo-Hc A 890 CD 4 MCU
Motor Casing A 48 Class 35 B A 890 CD 4 MCU
Discharge Elbow A 48 Class 35 B A 532 II C 15% CrMo-Hc A 890 CD 4 MCU
Power/Control Cable
Neoprene
Revised 10/2003
Supersedes all previously published warranties
Submersible Pumps KRT / KRTB (except grinder pumps) Warranty for Permanent Municipal Installations
Seven Year Or 12,500 Hour KRT Pump Warranty And
Ten Year Guide Cable Warranty For Permanent Municipal Installations
KSB, Inc. warrants to the Original End Purchaser that its
Pump(s) will be free from defects in workmanship and materials
covering parts and labor for a period of seven (7) years or twelve
thousand five hundred (12,500) hours of operation, and that its
Guide Cable will be free from defects in workmanship and
materials covering parts and labor for a period of ten (10) years
of operation when pumping abrasive-free, non-corrosive liquids
used in Permanent Municipal Installations. This warranty
commences on the date KSB, Inc ships the pump(s).
KSB Pump(s) are warranted for seven (7) years for use in
Sewage Collection systems or intermittent duty cycle pumping.
KSB Pump(s) are warranted for 12,500 hours of operation for
use in Sewage Treatment Processing or for continuous duty
cycle pumping. For the purpose of this clause, continuous duty
cycle is defined as twelve (12) hours per day average operation
time, or greater.
In the event that defects in workmanship or materials appear
during the term of the warranty, the Purchaser shall deliver
written claim of Warranty to the Company within ninety (90)
days of discovery. The obligation of KSB, Inc. under the
warranty shall be limited to replacement of defective part(s)
and/or labor whichever KSB, Inc., in its sole discretion, chooses
to elect. The Original End Purchaser shall be entitled to this
warranty provided that the terms of payment have been
complied with and the pump(s) with cable(s) attached or faulty
part(s) thereof have been returned freight prepaid to KSB, Inc.
or to an authorized KSB Service Facility and the defect has
been acknowledged in writing by KSB, Inc. to be caused by
faulty workmanship or defective material. Normal wear and tear
is specifically excluded from warranty coverage.
This warranty does not apply to KSB Grinder Pumps. The
warranty shall be void if the pump(s) or its part(s) have not been
used and maintained in accordance with the printed
instructions of KSB, Inc., or have been damaged wholly or in
part by misuse, accident, neglect, faulty electrical system, or
any other cause beyond the control of KSB, Inc.
Unless otherwise specified by KSB, Inc., the warranty period
shall be computed from the original shipping date to the date
the pump(s) and/or part(s) are returned to KSB, Inc. or, if repairs
are made on site, the warranty period shall be computed to the
date notice of defects is received by KSB, Inc.
Pump(s) or part(s) repaired or replaced will be returned at the
cost of the Original End Purchaser. Repairs or replacement
parts are warranted free from defects in workmanship and
materials for the longer of the un-expired term of this warranty
or ninety (90) days from the date KSB, Inc. ships such repaired
or replaced items, and all other terms and conditions of this
warranty shall apply. The extent of the Original End
Purchaser’s share in the repair or replacement cost detailed
below shall be paid prior to shipment by KSB, Inc.
Electrical system schematics (including bills of material) may be
required to support any warranty claims at the request of KSB,
Inc. This documentation will normally be required in the case
of pumps or 20 horsepower and larger.
KSB, Inc. will bear the cost for such repair or replacement as
follows:
Item
Categories
I
II
III
IV
Months after
Shipment
0-18
19-39
40-59
60 - 84
Hours of Operation
0-2,999
3,000-6,499
6,,500 – 9,999
10,000 – 12,500
A. Pumps
KSB Share of Cost
100%
50%
25%
10%
Months after
Shipment
0-120
-
-
-
B. Guide Cables
KSB Share of Cost
100%
-
-
-
KSB, INC. WILL NOT BE RESPONSIBLE FOR TRAVEL EXPENSES, RENTED EQUIPMENT, OUTSIDE CONTRACTORS’ FEES,
UNAUTHORIZED REPAIR, SHOP EXPENSES OR FOR PUMPS PURCHASED OR USED WITHOUT KSB SUPPLIED POWER CABLE(S).
THE WARRANTIES MADE HEREIN BY KSB, INC. ARE IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.
KSB, INC. DISCLAIMS ANY AND ALL WARRANTIES FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. KSB, INC.
ASSUMES NO LIABILITY FOR LOSS OF USE, LOSS OF PROFIT, OR ANY DIRECT, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES OF ANY KIND.
No sales agent or sales representative or any other person is authorized to modify, extend, or enlarge this Warranty. Any modification,
extension, or enlargement of this Warranty shall not bind KSB, Inc.