2 PHASE HYBRIDE STAPPENMOTOR

Datasheet Size 23 Series

Versie: 1.1

Step Angle: 1.8 Degree

Positional Accuracy: 5%

Number of phases: 2

Temperature rise: 80 degree max.

Dielectric strength: 500 Vdc

Insulation resistance: 100 Mohm (500 Vdc )

Insulation class: B

Radial play: 0.025 mm (450 g load)

N A Ohm V mH Shaft Kg mm

23LC041-025-8W-F6-0.5 0.5 1.25 0.76 0.94 0.75 F6 0.47 41

23LC041-025-8W-F6.F6-0.5 0.5 1.25 0.76 0.94 0.75 F6 S6 0.48 41

23LC041-025-8W-F8-0.5 0.5 1.25 0.76 0.94 0.75 F8 0.47 41

23LC041-025-8W-F8.F8-0.5 0.5 1.25 0.76 0.94 0.75 F8 S8 0.48 41

23LC051-025-8W-F6.35-1.0 1 1.25 0.9 1.1 1.5 F6.35 0.63 51

23LC051-025-8W-F8-1.0 1 1.25 0.9 1.1 1.5 F8 0.63 51

23LC051-025-8W-F8.F8-1.0 1 1.25 0.9 1.1 1.5 F 8 F 8 0.64 51

23LC051-025-8W-F10-1.0 1 1.25 0.9 1.1 1.5 F10 0.63 51

23LC064-025-8W-F10-1.5 1.5 1.25 1.2 1.5 2.1 F10 0.89 64

23LC064-025-8W-F10.F10-1.5 1.5 1.25 1.2 1.5 2.1 F10 F10 0.89 64

23SM100-030-8W-F10-2.0 2 1.5 1.4 2.1 3 F10 1.5 100

23SM100-030-8W-F10.F10-2.0 2 1.5 1.4 2.1 3 F10 F10 1.5 100

23SM112-030-8W-F10-2.5 2.5 1.5 1.5 2.3 3.8 F10 1.7 112

23SM112-030-8W-F10.F10-2.5 2.5 1.5 1.5 2.3 3.8 F10 F10 1.7 112

N (Nm) = Koppel = Torque = Haltemoment = couple A (Ampere) = Stroom / spoel = Current / coil = Strom / spule = le courant / bobine Ohm (Ohm) = Weerstand / spoel = Resistance / coil = wiederstand / spule = resistance / bobine V (Volt) = Spanning /spoel = Voltage / coil = spannung / spule = tension / bobine MH ( mH ) = Zelfinductie / spoel = Selfinduction / coil = Selfinduction / spule = l’inductance Gcm2 (Gcm2) = Rotor inertia = Rotor inertia = Rotor inertia = le inertia de rotor Kg (Kg) = Gewicht van motor = Weight of steppermotor = Motorgewicht = le poids de moteur Mm (mm) = Lengte van motor = Length of steppermotor = Motor länge = la longueur de moteur

BIPOLAIRE MICROSTAP DRIVER

Datasheet M415C

Specifications:

Power Supply

Minimum Voltage: 18 Vdc

Maximum Voltage: 40 Vdc

Maximum frequentie : > 100 Khz

Microsteps

Minimum number of microsteps: 1

Maximum number of microsteps: 64

Number of Phases: 2

Steppermotor

Minimum Phase Current: 0.4 A

Maximum Phase Current: 1.5 A

Number of motorwires (2 phase): 4, 6, and 8

Signals microstapdriver for steppermotor ( low means current through opto )

Min puls high time 1 uS Min puls low time 1 uS DIR to PUL lead time 3 uS ENA to PUL lead time 3 uS

Datasheet Simple Breakout V1.2

CNC Breakout Board Simple with step and direction This Simple CNC Breakout board is used to connect an LPT port to

One (or more) steppermotor(s) or Servomotor in an easy way.

Power input

Power (+5V) is supplied by means of a USB cable. This

cable can be connected to either a separate powersupply or

to the computer through the USB port. If there is power, the

LED will turn on, indicating there is power.

Led

Led will turn on if there is power to the board. (USB input)

DB-25 connector

The DB-25 connector is usually connected to the LPT port

of the cnc system.

Switches input connector

The switches (for example home switches) can be

connected on this connector. The pins of this

connector are connected to pin 10,11,12,13 and 15 of

the LPT Connector (BD-25).

Step/dir output connector

The drivers of the cnc system are connected to this

connector. The contacts are connected to pin 2-9 of

the LPT (DB-25) connector.

Relais output

There are 4 output signals that can be used for

switching something (for example a relais to turn on

a milling motor, or cooling mist)

Power output

This is the ouput of the GND and +5Vdc of the

board.