dap lm4 manual en 111121 - radikal · pdf file3g / hd / sd sdi module option module 3g sdi...

digital

audio processing

series D*AP

Digital Audio Processor LM4

Jünger Audio Studiotechnik GmbH

Justus-von-Liebig-Strasse 7

D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]

www.junger-audio.com 1/14

hardware

• 1RU compact 19" processing device with front panel

• Front Panel displays 4ch LED bar graph, operating display, LED status display

• Front Panel buttons BYPASS, METER, 4x function control, SEL, MENU, ESC

• Rotary encoder predefined functions, context sensitive modes

• 4 channel audio DSP 2 Analog Devices® Sharc floating point processors

• 2 x AES3 and 2x AES3id on board with independent relay bypass and auto input selection

• 2 x SRC selectable per AES input

• External sync IN 75 Ω input (Word Clock, AES3id, Black Burst, Tri-Level)

• Sync OUT 75 Ω Word Clock output

• RJ45 network connector 100BaseT full duplex Ethernet interface

• USB "B" connector built in USB < > serial adapter to access the device service port

• 8 GPIs balanced inputs on 25pin Sub-D

• 8 GPOs relay change over contacts on 25pin Sub-D

• Aux power supply build in isolated 5 V supply for external GPI/O wiring

• Optional dual power supply load balanced, auto fail over

• One interface slot I/O expansion slot for option modules :

3G / HD / SD SDI module option module 3G SDI de-embedder / embedder with relay bypass

8Ch AES I/O module option module 4x AES3id I/Os with relay bypass

4Ch analog I/O module option module 4x analog line I/Os with relay bypass

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


block diagram

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


getting started – IP setup of the Base Unit via front panel

After power up the front panel shows the idle display :

SHORT-TERM 3s CH 1/2 IN -70.0 OUT -70.0

Now you must press <MENU> and afterwards turn the Rotary Encoder [RE] in either direction until you reach the CONFIG item. Press the <RE> and the menu item NETWORK will be displayed. Press <RE> again and you will enter the network setup menu:

IP 10. 110. 3. 73.

If you turn the RE now to the right, you may select between IP, MASK and GATEWAY. If you press the <RE> now you will enter the setup display of the respective item. Flashing arrow markers will appear in the first field, to indicate that you may change this value by turning the RE. Below an example for the IP address :

IP >10< 110. 3. 73.

Pressing <SEL> will move the cursor to the next address field(s). After performing the setup you must press <MENU>.to apply the changes:

IP CONFIG CHANGED OK : APPLY ESC : DISCARD

Pressing <RE> will store the changes and will reboot the device in order to apply it.

APPLYING CHANGES REBOOTING . . .

getting started – IP setup of the Base Unit via console interface The alternative tool to change the IP configuration of the device may be reached via the console interface. You must connect the D*AP-LM4 with the PC via an USB A to B cable. Before connecting the cable you must have the FTDI driver installed on your PC. You will get it from the Co web site: http://www.ftdichip.com/FTDrivers.htm You must go for the VCP (Virtual Com Port) Drivers section and select the "setup executable" that matches your PC processor. E.g. "CDM20814_Setup.exe". Download the file and run it. This will install the driver for the built in USB to serial converter . Now you can connect the cable and open a terminal program. You must set up the terminal for the virtual COM port assigned to the USB device and set the communication parameters to: 115200kBaud, 8, N, 1 no hand shake. Pressing <ENTER> inside the terminal window will open the console menu:

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


Go for item 2 and press <ENTER> :

"Your choice: 2" "Current network configuration IP Address : 10.110.58.78 Netmask ... : 255.255.0.0 Gateway ... :

You must enter IP address and netmask. The gateway entry is optional.

Enter new IP address, press ENTER to cancel : 10.1 10.100.78 Enter new netmask, press ENTER to cancel : 255.255 .0.0 Enter new gateway, press ENTER to configure withou t gateway : Network configuration has been changed. Please reb oot the device To activate the new settings.

Select item 8 and press <ENTER> : Do you want to reboot the device ?

Press small "y" :

Do you want to reboot the device ? y

Press <ENTER>

Rebooting the device ……..

After reboot has finished the new IP configuration is active.

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


getting started – IP setup of the Base Unit via web browser

* Read the default IP address printed on a label between mains sockets. * Set up network parameters of the PC which meet the default IP address of the Base Unit

(net mask = 255.255.0.0). * Connect the device with the PC either by an Ethernet cross over cable or by a switch. * Open a browser and type the device IP address into the URL field and press <ENTER>.

This will open the AUDIO PROCESSOR >> Overview pane of the GUI. * Click on SYSTEM >> Config will open the following page::

Enter the desired network configuration into the marked area and press <Change network configuration> . Afterwards you must reboot the device in order to activate the new IP configuration. ! Important Note: After reboot the web browser can not communicate with the device . You must enter

the new IP address in the URL field and you must change the IP settings of your PC accordingly.

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


operating - menu structure of the Front Panel :

The display after power up – the idle display – shows the input "IN" and output "OUT" short term (3secs.) loudness of the programs processed by the respective device channels. E.g.:

SHORT-TERM 3s CH 1/2 IN -70.0 OUT -70.0

If you turn the RE the display will change to the True Peak Hold display of the respective channels:

TRUEPEAK-HOLD CH 1/2 IN -70.0 OUT -70.0

And vice versa. If you press <SEL> you will see the values of the other processing channels. Pressing <ESC> will reset the display reading (HOLD reset). The 4 direct function buttons of the front panel will move you to the respective function blocks where the RE selects the respective items . <MODE> LOUDNESS MODE > LINK MODE > SYNC SOURCE <INPUT> INPUT GAIN > INPUT ROUTING > BIT TRANSPARENT <LEVELER> ENABLE > LOUDNESS TARGET > AGC RELEASE TIME > MAX GAIN > FREEZ LEVEL > TP MAX GAIN > TP RESPONSE > <LIMITER> ENABLE > MAX TRUE PEAK > PROCESSING The overall parameter menu structure is shown on the next page.

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


operating – Web GUI

Type the device IP address into the URL field of a browser and you will get the initial web page of the D*AP-LM4 :

From here you may navigate through the various settings of the device

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


technical data base unit

• Power supply optional dual power supply, auto fail over AC 85 V – 264 V, 50 Hz … 60 Hz 58W max

• AES inputs BNC AES3id, 75 Ω, unbalanced, 24 Bit, 48 kHz, 0.3 … 5.0 Vpp

• AES inputs XLR AES3, 110 Ω balanced, 24 Bit, 48 kHz, 0.3 … 5.0 Vpp

• Input auto selection between AES3id (leading) and AES3

• Sample rate converters : 24 Bit, 32 kHz … 192 kHz, THD+N: < 130 dB @ 0 dBFS

• AES outputs BNC AES3id, unbalanced, 1 Vpp @ 75 Ω power fail bypass relay between each BNC in and out

• AES outputs XLR AES3, 3.3 Vpp @ 110 Ω power fail bypass relay between each XLR in and out

• Sync internal 48 kHz, +/- 10 ppm

• Sync input AES3id: 48 kHz, 1 V +/- 10% @ 75 Ω Wordclock: 48 kHz, 1 V … 3 V @ 75 Ω Video: Black Burst or Tri Level, 0.5 V … 1.0V @ 75 Ω

• Sync output Wordclock: 2 Vpp @ 75 Ω

• Network RJ45 rear connector 10/100MBit Ethernet auto sense, full duplex, auto MDI/X

• USB USB 2.0 "B" build in FTDI USB to RS232 converter

• GPI 5 V – 30 V balanced, auto polarity

• GPO relay change over contacts, 200 mA / 24 V (DC/AC)

• Environmental operating temperature 0 ºC to 50 ºC Base Unit - fan cooled non operating -20 ºC to 70 ºC humidity 90%, non condensing

• Dimensions 19", 1RU, depth 27 cm

• Weight net weight approx. 4 kg, shipping weight 6,5 kg

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


base unit rear connectors - pin assignment

connector : GPI

female 25-pin Sub-D

1 GPI_1a

2

3 GPI_2a

4 GPI_3a

5 GPI_3b

6 GPI_4a

7

8 GPI_5b

9 GPI_6a

10 GPI_6b

11 GPI_7a

12 GPI_7b

13 GPI_8b

14 GPI_1b

15 GPI_2b

16

17

18

19 GPI_4b

20 GPI_5a

21

22

23 Isolated 5V +

24 Isolated 5V -

25 GPI_8a

connector : GPO

female 25-pin Sub-D

1 GPO_8_NC

2 GPO_8_NO

3 GPO_7_common

4 GPO_6_NC

5 GPO_6_NO

6 GPO_5_common

7 GPO_4_NC

8 GPO_4_NO

9 GPO_3_common

10 GPO_2_NC

11 GPO_2_NO

12 GPO_1_common

13

14 GPO_8_common

15 GPO_7_NC

16 GPO_7_NO

17 GPO_6_common

18 GPO_5_NC

19 GPO_5_NO

20 GPO_4_common

21 GPO_3_NC

22 GPO_3_NO

23 GPO_2_common

24 GPO_1_NC

25 GPO_1_NO

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


technical data – interface modules – 3G SDI De-Embedder / Embedder [SDI 150]

• SDI input standards (auto sensing) 3G - SMPTE 424/425M (Level A/B) HD - SMPTE 292M SD - SMPTE 259M formats 1080p23.98, 24, 25, 29.97, 30, 50, 59.95, 60 1080i50, 59.94, 60 720p23.98, 24, 25, 29.97, 30, 50, 59.94, 60 625i50 525i59.94, … connector BNC IEC 169-8) 75 Ω return Loss > 15 dB (typ. > 18dB) from 5MHz to 1485 MHz > 10 dB (typ. > 11 dB) from 1485 MHz to 2970 MHz adaptive equalization, typical of Belden 1694A coaxial cable 250 m at 270 Mbps 250 m at 1.485 Gbps 150 m at 2.97 Gbps jitter tolerance Timing: > 2UI, Alignment: > 0.7 UI • SDI output standards 3G - SMPTE 424/425M (Level A/B) HD - SMPTE 292M SD - SMPTE 259M formats 1080p23.98, 24, 25, 29.97, 30, 50, 59.95, 60 1080i50, 59.94, 60 720p23.98, 24, 25, 29.97, 30, 50, 59.94, 60 625i50 525i59.94, … quantization 10Bit connector BNC IEC 169-8) 75 Ω return loss > 15 dB (typ. > 18dB) from 5MHz to 1485 MHz > 10 dB (typ. > 11 dB) from 1485 MHz to 2970 MHz signal level 800 mV +/- 10% D.C. offset 0.0 V +/- 0.5 V rise and fall time < 135 ps at HD/3G, < 800 ps at SD overshoot < 10% of amplitude output jitter Timing: < 0.5 UI, Alignment: < 0.2 UI

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


• Special features relay bypass (manual or automatic on power fail) 320 ms video delay (number of frames depends on the video format) 16 channel audio de-embedder / embedder VANC (SMPTE 2020-2) de-embedder / embedder 16 x 4 de-embedder matrix (mono routing) 20 x 16 embedder matrix (mono routing) 320 ms audio delay per embedder channel automatic compensation of non processed audio signals for video delay

technical data – interface modules – 4x AES I/O [DD 188] connector 25pin Sub-D female inputs 110 Ω balanced or 75 Ω unbalanced jumper selection 0.3 V … 5.0 Vpp sample rate converter 24 Bit, input sample rate 32 kHz … 192 kHz, THD+N < 130 dB @ 0 dBFS outputs 110 Ω balanced or 75 Ωunbalanced jumper selection 4.0 Vpp balanced, 1.0 Vpp @ 75 Ω power fail relay bypass technical data – interface modules – 4x analog I/O [AN 144] connector 25pin Sub-D female input impedance: > 10 kΩ , electronically balanced max input level: 0.0 dBu … +24 dBu adjustable in 0.5 dB steps dynamic range: 115 dB THD+N: @ -1 dBFS, 15 dBu: -90 dB frequency response: 20 Hz … 22 kHz (-2.0 dB) crosstalk @ 20 kHz: > 100 dB calibration gain mismatch: < 0.3 dB output impedance: 5 Ω, electronically balanced max. output level @ 0 dBFS: 0.0 dBu … +24 dBu adjustable in 0.5 dB steps dynamic range: 112dB THD+N @ -1 dBFS: 92 dB frequency response: 20 Hz … 22 kHz (-2.0 dB) crosstalk @ 20 kHz: > 100 dB gain mismatch balanced / unbalanced: < 0.3 dB power fail relay bypass

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


optional interface modules – 4x analog I/O & 4x AES I/O

pin assignment

connector : analog I/O

female 25-pin Sub-D

1 OUT-4 +

2 GND

3 OUT-3 -

4 OUT-2 +

5 GND

6 OUT-1 -

7 IN-4 +

8 GND

9 IN-3 -

10 IN-2 +

11 GND

12 IN-1 -

13

14 OUT-4 -

15 OUT-3 +

16 GND

17 OUT-2 -

18 Out-1 +

19 GND

20 IN-4 -

21 IN-3 +

22 GND

23 IN-2 -

24 IN-1 +

25 GND

connector : AES I/O

female 25-pin Sub-D

1 OUT-4 +

2 GND

3 OUT-3 -

4 OUT-2 +

5 GND

6 OUT-1 -

7 IN-4 +

8 GND

9 IN-3 -

10 IN-2 +

11 GND

12 IN-1 -

13

14 OUT-4 -

15 OUT-3 +

16 GND

17 OUT-2 -

18 OUT-1 +

19 GND

20 IN-4 -

21 IN-3 +

22 GND

23 IN-2 -

24 IN-1 +

25 GND

digital

audio processing

series D*AP




D -12489 Berlin

Germany

phone: +49-30-677721-0

fax: +49-30-677721-46

[email protected]


Geräteart : Digital Audio Processor Type of equipment : Digital Audio Processor Produkt / Product : DAP-LM Das bezeichnete Produkt stimmt mit den Vorschriften folgender EU-Richtlinie(n) überein: The aforementioned product complies with the following Europaen Council Directive(s): 89/336/EWG (geändert durch 91/263/EWG und 92/31/EWG)

(changed by 91/263/EEC and 92/31/EEC) Richtlinie der Rates zur Angleichung der Rechtsvorschriften der Mitgliedsstaaten über die elektromagnetische Verträglichkeit Council Directive on the approximation of the laws of the Member States relating to electromagnetic compatibility

73/23/EWG (geändert durch 93/68/EWG)

(changed by 93/68/EEC) Richtlinie des Rates vom 19. Februar 1973 betreffend elektrische Betriebsmittel zur Verwendung innerhalb bestimmter Spannungsgrenzen Council Directive of February 19th 1973 concerning electircal equipment for operation within certain voltage limits

Zur vollständigen Einhaltung dieser Richtlinie(n) wurden folgende Normen herangezogen: To fully comply with this(these) Directive(s), the following standards have been used: EN 55022 : 1987 EN 50082-1 : 1993 EN 60065 : 2002 Dieser Erklärung liegen zugrunde : Prüfbericht(e) des EMV-Prüflabors Interne Vorschriften zur Sicherheits-Prüfung This certification is based on : Test report(s) generated by EMC-test laboratory Internal regulations for safety check MEB Messelektronik Berlin : Kalibrier- und Prüflabor accredited EMC laboratory Aussteller / Holder of certificate : Jünger Audio-Studiotechnik GmbH Justus-von-Liebig-Strasse 7 D - 12489 Berlin Berlin, 01.10.2011 ..................................................................................... (Ort/Place) (Datum/Date) (Herbert Jünger, Geschäftsführer / Managing Director)

KONFORMITÄTSERKLÄRUNG

DECLARATION OF CONFORMITY

dap lm4 manual en 111121 - radikal · pdf file3g / hd / sd sdi module option module 3g sdi...

Documents