cyclo hbb catalogsumitomo

7/30/2019 Cyclo HBB Catalogsumitomo

1/28

SM-HELICAL BUDDYBOXIncorporating SM-Cyclo SpeedReducers and Keyless Taper-Grip Bushing

THEAVAILABLE

SOLUTION,

WORLDWIDE.

Catalog

07.040.50.005


2/28

This revolutionary new concept in shaft mountedgearmotors the SM-HELICAL BUDDYBOX fromSumitomo Machinery Corporation is safer, quieter

and requires less maintenance than any conventionalshaft mount.

Designed for easy installation, the SM-Helical Buddyboxeliminates the need for mounting foundations, fabrication,shaft modification, V belts, chains and guards.Maintenance and downtime are virtually eliminated.

S U M IT O M OSM-HELICAL BUDDYBOX SHAFT MOUNTED CYCLO GEARMOTOR

POWER TO STARTA REVOLUTION

The revolutionary SM-HELICAL BUDDYBOX combines the proven strength & durabilityof the SM-CYCLO speed reducer with the convenience of shaft mounting.

TAPER-GRIP BUSHINGBushing in fullengagement throughlength of the bore canbe installed fromeither side

NO KEYWAYReducer can beassembled to any shaft

The new Sumitomo SM-Helical Buddyboxreduces noise, wobble and the potentialrisks associated with the high liabilityconventional shaft mounted speedreducer shown below.

HELICALPORTIONMaximum speed of300 rpm allowsgrease lubrication

CYCLO GEARMOTOR PORTION500% Shock Load!Grease Lubricated!High Efficiency! Low Noise!Safe Installation!

MOTOR PORTIONAvailable with Brakes

INPUT PORTIONAllows for allstandard CYCLOmodifications AC motor, DCmotor, brakemotorand mechanicalvariable speed

Power Transmission Products4200 Holland Blvd., Chesapeake, VA 23323(757) 485-3355 FAX: (757) 485-3075

STOCKING and ASSEMBLY Los Angeles, CA Chicago, IL Dallas, TX

Toronto, Canada Vancouver, Canada Monterrey, Mexico

STOCKING and ASSEMBLY

CONTACT US TODAY FOR FREEPRICE AND SELECTION GUIDE

NO SHAFT MODIFICATIONTaper-Grip bushings areavailable to accommodateseveral shaft sizes

FPO


3/281

FEATURES AND BENEFITS

The SM-Helical Buddybox drive combines the worldfamous SM-CYCLO speed reducer and a single stageparallel shaft helical gearbox in shaft mounted design. Itincorporates the well known shock load characteristics ofthe cycloidal reducer with the adaptability of a shaft

mounted design.

The selection of SM-Helical Buddybox combinationis designed to maintain the high overload capacitythroughout the drive for which SM-CYCLO reducershave become famous, so Sumitomo is able to extend thestandard warranty to 24 months continuous operation.

HIGH EFFICIENCY EVEN AT HIGHRATIOS

Overall efficiency of the SM-Helical Buddyboxapproaches 95% even at reduction ratios up to 416:1.

The gearmotor and reducer design illustrated in thisbrochure comprise a standard SM-CYCLO gearmotor orreducer attached to a 3.5:1 (nominal) ratio, shaftmounted, helical speed reducer with hollow bore.

The SM-Helical Buddybox is secured to the driveshaft using a Taper-Grip bushing locking system.

EASE OF INSTALLATIONCompare the SM-Helical Buddybox to other shaft

mount torque drives. The drive is delivered completelyassembled and ready for fitting on the driven shaft.

NO ON-SITE ASSEMBLYREQUIREDWith other torque arm drives, assembly of the motor,

motor platform, sheaves, belts, belt guard, bushing andtorque arm is required. With SM-Helical Buddybox thebushing is already in place and only the torque armneeds fitting.

KEYLESS TAPER-GRIP BUSHINGThe principle of using locked tapers to secure power

transmission components has been established formany years. Our bushing system is based on the well

known locking capabilities of conventional taperbushings with one very significant difference: the HelicalBuddybox Taper-Grip bushing has a series of tapersurfaces in the form of a continuous helix. The tapersare machined in the hub and on the bushings in the formof a shallow screw thread, which enables the bushing tobe installed from either end of the output hub, dependentonly on customer choice and convenience. With thebushing assembled into the front face of the gear unit,access to the locking screws is immediate and

unobstructed. Similarly, if the front face must be clear thenthe bushing can be fitted to the reverse side. The lockingsurface goes completely through the bore.

TAPER-GRIP BUSHING FEATURES Standard bores require no key or keyway

Accessible locking arrangement

Reversible bushing assembly

Resistant to fretting corrosion

Easy removal of gear unit

PRODUCT LIABILITY & SAFETY

NO Belts NO Assembly Errors

NO Sheaves NO Guard

NO Injuries NO Noise

ASSEMBLYAfter the bushing is screwed into the hub, the reducer

can be conveniently positioned on the driven shaft.Locking is effected by sequentially tightening the screws,which draw the bushing axially against the opposingtapers in the hub, thus generating the clamping forcealong the whole length of the bushing in contact with the

shaft.Units can be easily installed on existing shafts that

may already include a keyway, even though the key willnot be required.

The bushing is manufactured from ductile iron whichhas properties similar to steel and has a certain degree ofself lubrication. This alleviates the problem of frettingcorrosion which is the cause of so many problemsassociated with the removal of shaft mount reducers.

Conventional Taper Bushing Helical BuddyboxTaper-Grip Bushing


4/282

BASIC INFORMATION AND RECOMMENDATIONS

LOAD CLASSIFICATIONS

PRIME MOVER DURATION OF SERVICE UNIFORM MODERATE SHOCK HEAVY SHOCK

SM- SM- SM-AGMA Helical AGMA Helical AGMA HelicalBuddybox Buddybox Buddybox

reducer reducer reducer

Occasional 1/2 hr. per day *0.50 *0.50 *0.80 *0.80 1.25 1.20

ELECTRICIntermittent 3 hrs. per day *0.80 *0.80 1.00 1.00 1.50 1.40

MOTORUp to 10 hrs. per day 1.00 1.00 1.25 1.20 1.75 1.60

24 hours per day 1.25 1.20 1.50 1.40 2.00 1.80

SERVICE FACTORSRECOMMENDED REDUCER SERVICE FACTORS

*Maximum momentary or starting load must not exceed 300% of gear reducer rating (rating meaning service factor of 1.0). Time specifiedfor occasional and intermittent service refers to total operating time per day.

GENERALSelection of the SM-Helical Buddybox should be

based on actual horsepower and torque requirementsat the output shaft. Unlike some conventional gearreducers, the SM-Helical Buddybox maintains very high

efficiency over a wide range of ratios. Proper selectionfrequently permits the use of reduced input powerrequirements without sacrificing torque at the outputshaft.

DRIVE RATINGSStandard SM-Helical Buddybox drives are designed

and built for long, minimum maintenance, 10 hour dailyservice under conditions of uniform loads (equivalent toAGMA service factor 1.0). When an application involvesmore severe conditions, catalog ratings must be dividedby the proper service factors.

SERVICE FACTORIn general, gear drives are rated for a specific

application by the use of service factors. Eachapplication has its own conditions and operatingrequirements. There are three load classifications:uniform, moderate shock, and heavy shock.These are further classified into duration of service perday and the prime mover (see table below).

Duration of service, frequency and severity of shockmust be determined in order to select the proper SM-Helical Buddybox drive for a specific application. Toassist in the selection process, AGMA has definedstandard service factors. However, the service factors tobe used for the selection of the SM-Helical Buddybox

differ from the standard service factors of AGMA asshown in the table. The SM-Helical Buddybox reducerservice factors are smaller than those of AGMA becauseAGMA service factors are determined on the basis of thegear strength in conventional worm or helical speedreducers.

The SM-CYCLO portion of the SM-Helical Buddyboxhas a higher overload capacity than conventionalreducers as a result of a greater number of reductionelements in contact and the high quality material of thecomponents (i.e.: 52100 vacuum degassed steel).

EXCESSIVE OVERLOADSThe SM-Helical Buddybox speed reducer, when

used at AGMA Service Factor of 1.0, can withstand a

momentary peak torque of 200% of rated torque (100%overload). SM-Helical Buddybox speed reducers provide300% momentary intermittent shock load capacity andare warranted for 2 years from date of shipment. Referto our standard terms and conditions for our completewarranty.

CONTENTS

Basic Information & Recommendations . . . . . . . . . . . . 2Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 5AGMA Load Classifications . . . . . . . . . . . . . . . . . . . . . . 6GM Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

GM Dimensions (Single Reduction) . . . . . . . . . . . . . 8, 9GM Dimensions (Double Reduction) . . . . . . . . . . . 10, 11Reducer Ratings (1800 RPM) . . . . . . . . . . . . . . . . . . . 12Reducer Ratings (1200 RPM, 1500 RPM) . . . . . . 13, 14

Double Reduction Reducer Ratings (1800 RPM) . . . . 15Reducer Dimensions (Single Reduction) . . . . . . . 16, 17Reducer Dimensions (Double Reduction) . . . . . . . 18, 19General Construction Helical Gear Case . . . . . . . . . . 20Mixer Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Standard Motor Characteristics . . . . . . . . . . . . . . . . . . 23Torque Arm Information . . . . . . . . . . . . . . . . . . . . . . . 24


5/283

INSTALLATION

The Helical Buddybox Taper-Grip bushing isdesigned to give an easy on, easy off fit to the shaft forassembly and maintenance while giving a firm grip tothe shaft during operation. The Taper-Grip bushingmay be fitted from either end of the hub; you should

ensure you have adequate access for correct tighteningof the screws.

Note: Satisfactory performance depends on properinstallation. Therefore all instructions on this page andin the Helical Buddybox Operation and MaintenanceManual must be followed carefully.

Fitting the Reducer on the Shaft

1. Check the size and condition of the shaft to which thereducer will be fitted. Permissible shaft tolerances aregiven in Table 1 below.

2. Ensure all mating surfaces of the hub, the inside andoutside diameters of the Taper-Grip bushing and theshaft are free from burrs and corrosion. Clean eachsurface with a solvent to remove all traces of greaseand oil.

3. Lightly oil each screw and insert into the bushingflange; ensure they do not protrude beyond the rearface.

4. Insert the face keys of the thrust collar into the slotson the hub and centralize. Screw the tapered bushing

into the hub in a clockwise direction until the flangecontacts the thrust collar.

5. Unscrew the Taper-Grip bushing until the screws arealigned with the pockets in the face of the thrust

collar and a gap of 1mm minimum exists between theflange and thrust collar. This may be easier if one ofthe screws is removed and the pocket viewedthrough the threaded hole. Finger tighten all screwsinto the pockets.

6. Slide the reducer onto the shaft at least as far as thecounter bore in the Taper-Grip bushing. Graduallytighten each screw in a star pattern to the torquelevels shown in Table 2.

7. Install the torque arm assembly if one is used.

8. After mounting is complete, the Helical Buddybox canthen be filled with oil. Please follow proper guidelinesfor oil lubrication.

For complete details regarding mounting andlubrication, please refer to the Helical BuddyboxO&M Manual.

Shaft Dia. Tolerance

34" - 118" +0 - .005"

1316" - 2" +0 - .006"

2116" - 318" +0 - .007"

3316" - 434" +0 - .008"

Table 1 Permissible Shaft Tolerance

SizeScrew Size

Screw Torque (lb. ft.)Qty. & Part Number

AA 6 X M10 942710 23

A 6 X M12 942727 37.5

B 6 X M12 942727 37.5

C 6 X M16 942735 94

D 6 X M20 942740 180

E 6 X M20 942740 180

Table 2 Bushing Screw Tightening Torques

Table 3 Stock Bushing Bores

Size Inch Sizes Metric Sizes *Min.

Bore**

AA 1316, 1716 30, 40 1316

A 11516, 2316 50, 55 11116

B 2316, 2716 60, 65 11516

C 2716, 21516 65, 75 2316

D 21516, 3716 75, 85 2716

E 3716, 31516 90, 100 21516

** Min. Bore Is Also Stock But Needs Slitting.

Inch ToleranceMetric Tolerance*(mm) (mm)

1316 - 158 +.003 / .001 30 - 40 .053 / .020

11116 - 11516 +.003 / .001 40 - 50 .064 / .025

2 - 2716 +.003 / .001 50 - 65 .076 / .030

212 - 3716 +.003 / .001 65 - 80 .076 / .030

312 - 31516 +.004 / .001 80 - 100 .090 / .036

Table 4 Bushing Bores Tolerances

*Tolerances are F8.

Note: Shaft runout TIR should be no greater than .001.


6/284

NOMENCLATURE

The complete Buddybox is specified by the use of 12 references.

E H Y M S

Buddybox product codeOutput shaft orientation

Mounting style

Input connection

Special feature

0 5

Gearmotor HP (applies only to 1750 rpm)

A A 4 0 9 0

Frame sizeAGMA class (gearmotor only)

A Y1 B 21

Installation position

Brake (gearmotor only)

Nominal total ratio

Shaft specification

Y

12

Table 1 Helical Buddybox Product Code

PREFIX TYPE

E Helical Gear

Table 2 Output Shaft Orientation

PREFIX TYPE

H Horizontal

V Vertical

Table 3 Mounting Style

PREFIX TYPE

Y Shaft Mount

F Flange

Table 4 Input Connection

PREFIX INPUT

REDUCER W/MOTOR CONNECTION

M Integral Motor

Free input Shaft

J JM C face Adaptor

P PM Top Mount

Hollow input ShaftX XM (Size A Buddybox

only)

Table 5 Mounting Style

PREFIX

S Special

Standard

Table 6 Gearmotor HP (applies only to 1800 RPM)

PREFIX HP PREFIX HP

01 1/8 3 3

02 1/4 5 5

03 1/3 8 7.5

05 1/2 10 10

08 3/4 15 15

1 1 20 20

1H 1 1/2 25 25

2 2 30 30

Table 7 Frame Size

GEAR SIZE CYCLO SIZE

AA4090

4095

A4100

4105

4110

B 4115

4125

C4145

4155

D4160

4165

E 4170

4175

11


7/285

NOMENCLATURE

Table 9 AGMA Class (Gearmotor only)

Table 11 Brake (Gearmotor only)

SUFFIX CLASS

B WITH BRAKE

WITHOUT BRAKE

Table 10 Installation Position

Shaft Mount

Table 12 Nominal Total Ratio

HBB CYCLO HBB CYCLORATIO RATIO RATIO RATIO

11 3 88 25

14 4 102 29

21 6 123 35

28 8 151 43

39 11 179 51

46 13 207 59

53 15 249 71

60 17 305 87

74 21

Helical Buddybox Exact Ratio

AA 3.4667 C 3.5000

A 3.5000 D 3.4667

B 3.5000 E 3.4667

Table 8 Shaft Specification (Hollow or Solid Shaft only)

SUFFIX SPECIFICATION

Y INCH

G METRIC DIN

METRIC

Helical Buddybox

Flange Mount

Note: Overflow is located next to drain on

bottom.

(output shaft horizontal - bottom)

(output right side, viewed from input side) (output left side, viewed from input side) (output vertical, input below)

(output shaft horizontal - top)

STANDARD

(output vertical, input above)

SUFFIX CLASS

A I

B II

C III

F1

F2

F3

F4

F5*

F6*

*Consult Factory

Helical BuddyboxY1 Y3

Y2

Y4

Note: Overflow is located next to drain onbottom.

(output shaft horizontal - bottom)

(output right side, viewed from input side) (output left side, viewed from input side) (output vertical, input below)

(output shaft horizontal - top)

STANDARD

(output vertical, input above)Y5*

Y6*

*Consult Factory


8/286

Type Of Type OfApplication Load


AgitatorsPure liquids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Liquids and solids . . . . . . . . . . . . . . . . . . . . . . . . . . MVariable-density liquids . . . . . . . . . . . . . . . . . . . . . . MBlowers

Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ULobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MVane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Brewing and DistillingBottling machinery . . . . . . . . . . . . . . . . . . . . . . . . . . UBrew kettles, cont. duty . . . . . . . . . . . . . . . . . . . . . . UCookers, cont. duty . . . . . . . . . . . . . . . . . . . . . . . . . UMash tubs, cont. duty . . . . . . . . . . . . . . . . . . . . . . . UScale hopper, frequent starts . . . . . . . . . . . . . . . . . M

Can Filling Machines . . . . . . . . . . . . . . . . . . . . . . . . . . . UCane Knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCar Dumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HCar Pullers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MClarifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UClassifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MClay Working Machinery

Brick press . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HBriquette machine . . . . . . . . . . . . . . . . . . . . . . . . . . HClay working machinery . . . . . . . . . . . . . . . . . . . . . MPug mill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

CompressorsCentrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ULobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MReciprocating, multi-cylinder . . . . . . . . . . . . . . . . . . MReciprocating, single-cylinder . . . . . . . . . . . . . . . . . H

Conveyors Uniformly Loaded or FedApron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UBelt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UBucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UChain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UFlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UOven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Conveyors Heavy Duty, Not Uniformly FedApron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MBelt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MBucket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MChain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MFlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLive roll oven . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MReciprocating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MShaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H

Cranes (except for dry dock cranes)

Main hoists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UBridge travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STrolley travel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S

CrusherOre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HStone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSugar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

DredgesCable reels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MConveyors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCutter head drives . . . . . . . . . . . . . . . . . . . . . . . . . . HJig drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HManeuvering winches . . . . . . . . . . . . . . . . . . . . . . . MPumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MScreen drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HStackers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MUtility winches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Dry Dock Cranes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SElevators

Bucket, uniform load . . . . . . . . . . . . . . . . . . . . . . . . UBucket, heavy load . . . . . . . . . . . . . . . . . . . . . . . . . MBucket, cont. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UCentrifugal discharge . . . . . . . . . . . . . . . . . . . . . . . UEscalators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Freight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MGravity discharge . . . . . . . . . . . . . . . . . . . . . . . . . . UMan lifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPassenger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S

Extruders (plastics)Blow molders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCoating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UFilm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPre-plasticizers . . . . . . . . . . . . . . . . . . . . . . . . . . . . MRods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UTubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

FansCentrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UCooling towers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SForced draft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SInduced draft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLarge (mine, etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . M

Large (industrial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLight (small diameter) . . . . . . . . . . . . . . . . . . . . . . . U

FeedersApron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MBelt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MDisc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UReciprocating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Food IndustryBeet slicer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCereal cooker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UDough mixer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MMeat grinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Generators (not welding) . . . . . . . . . . . . . . . . . . . . . . . . UHammer Mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HHoists

Heavy duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HMedium duty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSkip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Laundry Washers Reversing . . . . . . . . . . . . . . . . . . . MLaundry Tumblers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLine Shaft

Drive processing equipment . . . . . . . . . . . . . . . . . . MLight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UOther line shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Lumber IndustryBarkers hydraulic and mechanical . . . . . . . . . . . S

Burner conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . . MChain Saw and Drag Saw . . . . . . . . . . . . . . . . . . . . . . . H

Chain transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HCraneway transfer . . . . . . . . . . . . . . . . . . . . . . . . . . HDe-barking drum . . . . . . . . . . . . . . . . . . . . . . . . . . . HEdger feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HGang feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MGeen chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MLive rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HLog haullockline . . . . . . . . . . . . . . . . . . . . . . . . . . HLog turning device . . . . . . . . . . . . . . . . . . . . . . . . . . HMain log conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . HOff bearing rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . MPlaner feed chains . . . . . . . . . . . . . . . . . . . . . . . . . MPlaner floor chains . . . . . . . . . . . . . . . . . . . . . . . . . MPlaner tilting hoist . . . . . . . . . . . . . . . . . . . . . . . . . . MRe-saw merry-go-round conveyor . . . . . . . . . . . . . MRoll cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSlab conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HSmall wasteconveyor-belt . . . . . . . . . . . . . . . . . . . USmall wasteconveyor-chain . . . . . . . . . . . . . . . . . MSorting table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTipple hoist conveyor . . . . . . . . . . . . . . . . . . . . . . . MTipple hoist drive . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Transfer conveyors . . . . . . . . . . . . . . . . . . . . . . . . . MTransfer rolls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTray drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTrimmer feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWaste conveyor . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Machine ToolsBending roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MNotching press, belt driven . . . . . . . . . . . . . . . . . . . SPlate planer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HPunch press, gear driven . . . . . . . . . . . . . . . . . . . . HTapping machine . . . . . . . . . . . . . . . . . . . . . . . . . . . HOther machine tools

Main drives . . . . . . . . . . . . . . . . . . . . . . . . . . . MAuxiliary drives . . . . . . . . . . . . . . . . . . . . . . . . . U

Metal MillsDraw bench carriage and main drive . . . . . . . . . . . MForming machines . . . . . . . . . . . . . . . . . . . . . . . . . . HPinch, dryer and scrubber rolls,

reversing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSlitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTable conveyors, nonreversing

Group drives . . . . . . . . . . . . . . . . . . . . . . . . . . MIndividual drives . . . . . . . . . . . . . . . . . . . . . . . . H

Table conveyors, reversing . . . . . . . . . . . . . . . . . . . SWire drawing and flattening machine . . . . . . . . . . . M

Wire winding machine . . . . . . . . . . . . . . . . . . . . . . . MMills, Rotary Type

Ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCement kilns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MDryers and coolers . . . . . . . . . . . . . . . . . . . . . . . . . MKilns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPebble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MRod, plain and wedge bar . . . . . . . . . . . . . . . . . . . . MTumbling barrels . . . . . . . . . . . . . . . . . . . . . . . . . . . H

MixersConcrete mixers, cont. . . . . . . . . . . . . . . . . . . . . . . MConcrete mixers, intermittent . . . . . . . . . . . . . . . . . MConstant density . . . . . . . . . . . . . . . . . . . . . . . . . . . UVariable density . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Oil IndustryChillers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MOil well pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SParaffin filter press . . . . . . . . . . . . . . . . . . . . . . . . . MRotary kilns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Paper MillsAgitators (mixers) . . . . . . . . . . . . . . . . . . . . . . . . . . M

Barker, hydraulic . . . . . . . . . . . . . . . . . . . . . . . . . . . MBarker, mechnical . . . . . . . . . . . . . . . . . . . . . . . . . . MBarking drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HBeater and pulper . . . . . . . . . . . . . . . . . . . . . . . . . . MBleacher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UCalenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCalenders, super . . . . . . . . . . . . . . . . . . . . . . . . . . . HConverting machine (except cutters, platers) . . . . . MConveyors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UCouch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCutters, platers . . . . . . . . . . . . . . . . . . . . . . . . . . . . HCylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MDryers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MFelt stretcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MFelt whipper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HJordans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HLog haul . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HPresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPulp machine reel . . . . . . . . . . . . . . . . . . . . . . . . . . MStock chest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSuction roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UWashers and thickeners . . . . . . . . . . . . . . . . . . . . . MWinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . U

Printing Presses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPullers, Barge Haul . . . . . . . . . . . . . . . . . . . . . . . . . . . . HPumps

Centrifugal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UProportioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MReciprocating

Single acting, 3 or more cylinders . . . . . . . . . . . . . MDouble acting, 2 or more cylinders . . . . . . . . . . . . M

Rotary-gear type . . . . . . . . . . . . . . . . . . . . . . . . . . . URubber and Plastics Industries

Crackers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HLaboratory equipment . . . . . . . . . . . . . . . . . . . . . . . MMixing mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HRefiners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MRubber calenders . . . . . . . . . . . . . . . . . . . . . . . . . . MRubber mill (2 on line) . . . . . . . . . . . . . . . . . . . . . . . MRubber mill (3 on line) . . . . . . . . . . . . . . . . . . . . . . . USheeter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTire building machines . . . . . . . . . . . . . . . . . . . . . . STire and tube press openers . . . . . . . . . . . . . . . . . . STubers and strainers . . . . . . . . . . . . . . . . . . . . . . . . MWarming mills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Sand Muller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MScreens

Air washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URotary, stone or gravel . . . . . . . . . . . . . . . . . . . . . . M

Traveling water intake . . . . . . . . . . . . . . . . . . . . . . . USewage Disposal Equipment

Bar screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UChemical fenders . . . . . . . . . . . . . . . . . . . . . . . . . . UCollectors, circuline or straightline . . . . . . . . . . . . . UDewatering screws . . . . . . . . . . . . . . . . . . . . . . . . . MGrit collectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UScum breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSlow or rapid mixers . . . . . . . . . . . . . . . . . . . . . . . . MSludge collectors . . . . . . . . . . . . . . . . . . . . . . . . . . . UThickeners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MVacuum filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Slab Pushers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSteering Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SStokers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USugar Industry

Cane knives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCrushers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MMills . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H

Textile IndustryBatchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCalenders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MCards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MDry cans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Dryers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MDyeing machinery . . . . . . . . . . . . . . . . . . . . . . . . . . MKnitting machines . . . . . . . . . . . . . . . . . . . . . . . . . . SLooms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MMangles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MNappers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MPads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MRange drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSlashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSoapers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSpinners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MTenter frames . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MWinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M

Windlass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S

U = Uniform Load H = Heavy ShockM = M oderate Shock S = Contact Sumitomo

AGMA LOAD CLASSIFICATIONS



9/287

HELICAL BUDDYBOX GEARMOTOR RATINGS (1800 RPM)

O/P SPEED 164 129 86 64 46 39 34 30 24 20 18 15 12 10 8.7 7.2 5.9

RATIO 11 14 21 28 39 46 53 60 74 88 102 123 151 179 207 249 305

MOTOR HP CLASS I SELECTIONS

1/8 AA4090 AA4090 AA4090 AA4090

1/4 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095

1/2 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 AA4095 A4105 A4105

3/4 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 AA4095 AA4095 AA4095 A4105 A4105 A4105 A4105

1 A4100 A4100 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 AA4095 A4105 A4105 A4105 B4110 B4115 B4115

1.5 A4100 A4100 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 A4100 A4105 A4105 B4110 B4115 B4115 B4115 C4145

2 A4100 A4100 A4100 A4100 A4100 A4105 A4105 A4105 A4105 A4105 A4105 B4110 B4115 B4115 B4115 C4145 C4145

3 A4105 A4105 A4105 A4105 A4105 A4105 A4105 A4105 A4105 B4115 B4115 B4115 B4115 C4145 C4145 C4145 C4145

5 B4110 B4110 B4110 B4110 B4110 B4110 B4110 B4115 B4115 B4115 C4145 C4145 C4155 C4155 D4160 D4165 D4165

7.5 B4125 B4125 B4125 B4125 B4125 B4125 B4125 B4125 C4145 C4145 C4145 C4155 D4160 D4165 D4165 E4175

10 C4145 C4145 C4145 C4145 C4145 C4145 C4145 C4145 C4155 D4160 D4160 D4165 D4165 E4175 E4175

15 C4145 C4145 C4155 C4155 C4155 C4155 C4155 D4160 D4165 D4165 D4165 E4175

20 C4145 C4145 C4155 C4155 D4165 D4165 D4165 D4165 E4175 E4175

25 D4165 D4165 D4165 E4175 E4175

30 E4170 E4175 E4175

MOTOR HP CLASS II SELECTIONS

1/8 AA4090 AA4090 AA4090 AA4090


1/2 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 AA4095 AA4095 A4100 A4105 A4105 A4105

3/4 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 A4100 A4105 A4105 B4110 B4110 B4110

1 A4100 A4100 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 A4100 A4100 A4105 A4105 B4110 B4110 B4115 B4115

1.5 A4100 A4100 A4100 A4100 A4100 A4100 A4100 A4100 A4100 A4105 A4105 B4110 B4110 B4115 B4115 C4145 C4145

2 A4105 A4105 A4105 A4105 A4105 A4105 A4105 A4105 A4105 B4110 B4110 B4115 B4115 B4115 C4145 C4145 C4145

3 A4105 A4105 A4105 A4105 A4105 A4105 A4105 B4110 B4110 B4115 B4115 B4115 C4145 C4145 C4145 C4155 D41655 B4115 B4115 B4115 B4115 B4115 B4115 B4115 B4115 C4145 C4145 C4145 C4145 D4160 D4160 D4165 E4170 E4175

7.5 B4125 B4125 B4125 B4125 C4145 C4145 C4145 C4145 C4145 C4155 D4160 D4165 D4165 E4170 E4175

10 C4145 C4145 C4155 C4155 C4145 C4145 C4145 C4145 D4160 D4160 D4165 D4165 E4175

15 C4155 C4155 C4155 D4165 D4165 D4165 D4165 E4170 E4175

20 D4165 D4165 D4165 D4165 E4175 E4175

25 E4170 E4170 E4175 E4175

MOTOR HP CLASS III SELECTIONS

1/8 AA4090 AA4090 AA4090 AA4095


1/2 AA4090 AA4090 AA4090 AA4090 AA4090 AA4090 AA4095 AA4095 AA4095 AA4095 AA4095 A4105 A4105 B4110 B4110

3/4 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 A4100 A4100 A4105 A4105 B4100 B4110 B4115 B41151 A4100 A4100 AA4095 AA4095 AA4095 AA4095 AA4095 AA4095 A4100 A4100 A4105 B4110 B4110 B4115 B4115 C4145 C4145

1.5 A4105 A4105 A4100 A4100 A4105 A4105 A4105 A4105 A4105 B4110 B4110 B4110 B4115 B4115 C4145 C4145 C4145

2 A4105 A4105 A4105 A4105 A4105 A4105 A4105 A4105 B4110 B4115 B4115 B4115 C4145 C4145 C4145 C4145 C4155

3 B4115 B4115 B4110 B4110 B4110 B4110 B4110 B4110 B4115 B4115 C4145 C4145 C4145 C4155 C4155 D4165 D4165

5 B4125 B4125 B4125 B4125 C4145 C4145 C4145 C4145 C4145 C4145 C4155 C4155 D4160 D4165 E4170 E4175

7.5 C4145 C4145 C4155 C4155 C4145 C4145 C4145 C4145 D4160 D4160 D4165 D4165 E4170 E4175

10 C4145 C4145 C4155 C4155 C4155 D4160 D4160 D4160 D4165 D4165 E4170 E4175

15 D4165 D4165 D4165 D4165 D4165 E4170 E4175 E4175

20 E4170 E4170 E4175 E4175


10/288

SINGLE REDUCTION GEARMOTOR DIMENSIONS

M

Q

I

N3

E

N2

F

N1

GDC

C MS

ML

MP

U

Y

S2

2X 3S1 X L

MT

Max. is Std.

FRAME MOTORB E F G H I J K M P Q T

UV W Y d

SIZE HP MAX MIN

1/8

AA4090 1/4 11.02 5.51 0.20 0.79 11.87 2.20 8.31 6.18 5.51 0.12 1.06 8.54 1716 1316 4.23 4.69 3.11 0.55AA4095 1/2

1

1/4

1/2

A41003/4

A41051 11.85 5.91 0.20 0.79 12.70 2.60 9.17 6.44 6.14 0.12 1.14 9.41 2316 11116 4.61 5.14 4.09 0.71

112

2

3

1/2

3/4

B41101

B4115112

14.49 7.48 0.20 0.98 16.10 3.39 11.42 7.97 7.24 0.12 1.22 11.65 2716 11516 5.69 6.40 4.49 0.71B4125

2

3

5

7.5

1

2

C41453

C41555 17.24 8.66 0.20 1.18 18.84 3.82 13.39 9.53 8.70 0.12 1.61 13.62 21516 2316 6.73 7.58 5.51 0.87

7.5

10

15

2

3

D4160 5

D4165 7.5 21.22 9.84 0.28 1.38 23.94 4.49 16.77 11.54 9.96 0.20 1.77 17.17 3716 2716 8.43 9.61 6.42 1.02

10

15

20

5

7.5

E4170 10 24.02 11.81 0.28 1.77 26.85 5.00 18.90 13.07 10.79 0.20 1.97 19.29 31516 21516 9.45 10.71 7.09 1.30E4175 15

20

25, 30

Dimensions shown are for reference only and are subject to change without notice, unless certified.Certified prints are available after receipt of an order; consult factory.

D1 DC KH N1 N2 N3 S2

2.56 5.91 3.54 1.02 1.02 1.02 M10

3.35 5.91 3.74 1.10 1.10 1.10 M12

3.94 8.03 4.33 1.26 1.26 1.34 M12

4.33 9.06 5.31 3.98 1.81 2.83 M16

5.12 11.81 6.38 3.62 2.17 3.62 M20

5.90 13.39 7.09 3.82 2.20 3.94 M20

Note: Dimensions continuedon opposing page.

AB


11/28

S x L S1 x L C AB ML MPWEIGHT

C AB ML MP MS MTWEIGHT

(LB) (LB)

12.01 3.07 4.69 64 13.39 4.41 68

M10x20 M10x20 13.66 4.80 3.98 4.88 66 14.92 4.80 4.96 4.88 1.54 70

14.45 4.37 68 15.71 5.36 73

16.06 4.49 3.82 5.83 77 17.76 4.49 5.51 5.83 3.67 84

14.80 4.80 3.98 4.88 86 16.06 4.80 4.96 4.88 1.54 90

15.59 2.12 88 16.85 3.39 2.40 92

M10x20 M12x12 17.20 4.49 3.82 5.83 97 18.90 4.49 5.51 5.83 3.67 4.88 103

18.50 4.69 3.94 6.30 106 20.94 4.69 6.38 6.30 4.53 5.12 11719.29 4.96 4.13 6.81 114 21.77 4.96 6.61 6.81 4.77 5.37 128

17.09 4.80 2.12 4.88 152 18.35 4.80 3.39 4.88 2.40 156

18.50 4.49 3.82 5.83 163 20.20 4.49 5.51 5.83 3.67 4.88 169

M12x12 M16x26 19.80 4.69 3.94 6.30 172 22.24 4.69 6.38 6.30 4.53 5.12 183

20.59 4.96 4.13 6.81 180 23.07 4.96 6.61 6.81 4.77 5.37 196

21.50 5.79 5.00 8.35 202 24.33 5.79 7.83 8.35 5.20 6.67 224

23.23 218 26.06 240

21.02 4.49 3.82 5.83 262 22.72 4.49 5.51 5.83 3.67 4.88 268

22.32 4.69 3.94 6.30 271 24.76 4.69 6.38 6.30 4.53 5.12 282

23.11 4.96 4.13 6.81 277 25.59 4.96 6.61 6.81 4.77 5.37 290

M16x30 M20x35 24.02 5.79 5.00 8.35 299 26.85 5.79 7.83 8.35 5.20 6.67 321

25.75 315 28.58 337

26.65 7.32 5.63 9.88 348 30.39 7.32 9.37 9.88 6.69 7.66 387

29.02 378 32.76 418

24.57 4.69 3.94 6.30 489 27.01 4.69 6.38 6.30 4.53 5.12 480

25.16 4.96 4.13 6.81 475 27.64 4.96 6.61 6.81 4.77 5.37 488

26.06 5.79 5.00 8.35 495 28.90 5.79 7.83 8.35 5.20 6.67 517

M20x35 M24x40 27.80 510 30.63 532

28.90 7.32 5.63 9.88 546 32.64 7.32 9.37 9.88 6.69 7.66 585

31.26 576 35.00 616

34.61 9.13 11.61 12.76 693 38.15 9.13 15.16 12.76 766

27.99 5.79 5.00 8.35 653 30.83 5.79 7.83 8.35 5.20 6.67 675

29.72 669 32.56 691

M20x35 M24x40 30.43 7.32 5.63 9.88 704 34.17 7.32 9.37 9.88 6.69 7.66 744

32.80 735 36.54 744

35.94 9.13 11.61 12.76 854 39.49 9.13 15.16 12.76 9.72 926

39.69 11.69 13.39 15.51 1019

FRAME MOTORLA N

SIZE HP

1/8

AA4090 1/4 4.72 0 4AA4095 1/2

1

1/4

1/2

A41003/4

A41051 6.10 30 6

112

23

1/2

3/4

B41101

B4115112

6.89 30 6

B41252

3

5

7.5

1

2

3

C4145 5 8.35 30 6

C4155 7.5

10

15

2

3

D4160 5

D4165 7.510.04 30 610

15

20

5

7.5

E4170 1011.02 22.5 8

E4175 15

20

25, 30

9

With Standard Motor Wi th Standard Motor & Brake


Note: Dimensions continuedfrom opposing page.

NS X L

LA

P

OIL FILL

V

W

B

H

2 - d

JT

P

K

KH


12/2810

DOUBLE REDUCTION GEARMOTOR DIMENSIONS


Max. is Std.

FRAME MOTORB E F G H I J K M P Q T

UV W Y d

SIZE HP MAX MIN

AA4095DA1/8

1/4, 1/311.02 5.51 0.20 0.79 11.87 2.20 8.31 6.18 5.51 0.12 1.06 8.54 1716 1316 4.23 4.69 3.11 0.55

1/8

A4105DA 1/4, 1/3 11.85 5.91 0.20 0.79 12.70 2.60 9.17 6.44 6.14 0.12 1.14 9.41 2316 11116 4.61 5.14 4.09 0.711/2

1/8

1/4, 1/3B4115DB

1/214.49 7.48 0.20 0.98 16.10 3.39 11.42 7.97 7.24 0.12 1.22 11.65 2716 11516 5.69 6.40 4.49 0.71

3/4, 1

1/4, 1/3

1/2C4145DB

3/4, 117.24 8.66 0.20 1.18 18.84 3.82 13.39 9.53 8.70 0.12 1.61 13.62 21516 2316 6.73 7.58 5.51 0.87

112

1/2

3/4, 1D4165DC

112, 221.22 9.84 0.28 1.38 23.94 4.49 16.77 11.54 9.96 0.20 1.77 17.17 3716 2716 8.43 9.61 6.42 1.02

3

1/2

3/4, 1

E4175DC 112, 2 24.02 11.81 0.28 1.77 26.85 5.00 18.90 13.07 10.79 0.20 1.97 19.29 31516 21516 9.45 10.71 7.09 1.30

3

5

D1 DC KH N1 N2 N3 S2

2.56 5.91 3.54 1.02 1.02 1.02 M10

3.35 5.91 3.74 1.10 1.10 1.10 M12

3.94 8.03 4.33 1.26 1.26 1.34 M12

4.33 9.06 5.31 3.98 1.81 2.83 M16

5.12 11.81 6.38 3.62 2.17 3.62 M20

5.90 13.39 7.09 3.82 2.20 3.94 M20


D1 U

Y

DC

E

M

Q

F

G

C

N3 S2

MP

MS

MT

N2

N1

2X 3S1 x L

AB


13/28

With Standard Motor With Standard Motor & Brake

11

FRAME MOTORLA N

SIZE HP

AA4095DA1/8

4.72 0 41/4, 1/3

1/8

A4105DA 1/4, 1/3 6.10 30 61/2

1/8

1/4, 1/36.89 30 6B4115DB

1/2

3/4, 1

1/4, 1/3

1/28.35 30 6C4145DB

3/4, 1

112

1/2

3/4, 110.04 30 6D4165DC

112, 2

3

1/2

3/4, 1E4175DC 112, 2 11.02 22.5 8

3

5

11




2 d

LA

V

B

H

P J

T

P

W

NS X L

K

KH

S x L S1 x L C AB ML MPWEIGHT

C AB ML MP MS MTWEIGHT

(LB) (LB)

13.92 3.07 4.69 71 15.30 4.41 74M10x20 M10x20

15.574.80

3.98 4.88 72 16.834.80

4.964.88 1.54

77

15.06 3.07 4.69 89 16.44 4.41 93

M10x20 M12x22 16.71 4.80 3.95 4.88 91 17.97 4.80 4.96 4.88 1.54 9517.50 4.37 93 18.76 5.36 100

17.03 3.07 4.69 157 18.41 4.41 161

18.68 4.80 3.96 4.88 160 19.94 4.80 4.96 4.88 1.54 164M12x22 M16x26

19.47 4.37 165 20.73 5.36 169

21.08 4.49 3.82 5.83 168 22.78 4.49 5.51 5.83 3.67 4.17 176

21.12 3.98 259 22.38 4.96 263

21.914.80

4.374.88

263 23.174.80

5.364.88 1.54

267M16x30 M20x35

23.52 4.49 3.82 5.83 266 25.22 4.49 5.51 5.83 3.67 4.17 274

24.82 4.69 3.94 6.30 274 27.26 4.69 6.38 6.30 4.53 5.12 287

24.88 4.80 4.37 4.88 515 26.14 4.80 5.36 4.88 1.54 526

26.30 4.49 3.82 5.83 518 28.00 4.49 5.51 5.83 3.67 4.17 533M20x35 M24x40

27.60 4.69 3.94 6.30 526 30.04 4.69 6.38 6.30 4.53 5.12 546

28.39 4.96 4.13 6.81 533 30.87 4.96 6.61 6.81 4.77 5.37 558

26.30 4.80 4.37 4.88 632 27.56 4.80 6.36 4.88 1.54 634

27.72 4.49 3.82 5.83 635 29.42 4.49 5.51 5.83 3.67 4.17 641

M20x35 M24x40 29.02 4.69 3.94 6.30 643 31.46 4.69 6.38 6.30 4.53 5.12 654

29.80 4.96 4.13 6.81 652 32.28 4.96 6.61 6.81 4.77 5.37 667

30.71 5.29 5.00 8.35 674 33.54 5.79 7.83 8.35 5.20 6.67 695


14/2812

HELICAL BUDDYBOX REDUCER RATING TABLE

SINGLE REDUCTION REDUCERS AT 1800 RPM INPUT (HP, in lbs.)

HBB CYCLOO/P RPM 164 129 86 64 46 39 34 30 24 20 18 15 12 10 8.7 7.2 5.9

RATIO 11 14 21 28 39 46 53 60 74 88 102 123 151 179 207 249 305

4090 HP 1.04 1.04 1.04 1.04 1.04 1.04 0.72 0.63 0.62 0.62 0.39 0.32 0.31 0.20 0.16

AATORQUE 693 924 1290 1520 1750 1980 1690 1760 2010 2420 1870 1820 2040 1580 1550

4095HP 1.89 1.89 1.89 1.88 1.79 1.68 1.51 1.15 1.04 0.90 0.80 0.56 0.51 0.40 0.40

TORQUE 1260 1680 2340 2750 3010 3200 3550 3210 3370 3510 3650 3180 3350 3160 3650

4100HP 2.48 2.48 2.48 2.48 2.31 1.97 1.96 1.95 1.95 1.68 1.30 0.98 0.93 0.73 0.63 0.48 0.48

ATORQUE 841 1070 1650 2200 2860 2880 3300 3710 4580 4690 4210 3830 4460 4150 4140 3790 4650

4105HP 4.22 4.22 4.22 4.22 4.22 4.22 4.22 3.26 3.10 2.22 2.11 1.59 1.44 1.03 0.94 0.77 0.75

TORQUE 1430 1820 2810 3750 5220 6160 7100 6210 7280 6200 6830 6056 6900 5850 6180 6090 7260

4110HP 5.20 5.20 5.20 5.20 5.20 5.07 5.07 4.80 4.01 2.88 2.86 2.40 1.96 1.45 1.34 0.99 0.98

TORQUE 1760 2240 3470 4620 6440 7400 8530 9140 9420 8040 9260 9370 9390 8240 8800 7820 9490

B 4115HP 6.80 6.80 6.80 6.80 6.80 6.80 6.80 6.80 5.52 5.01 4.45 4.22 3.01 2.78 2.15 1.51 1.44

TORQUE 2310 2930 4530 6040 8420 9930 11400 13000 13000 14000 14400 14800 14400 14800 14100 11900 13900

4125 HP 10.5 10.5 10.5 10.5 7.51 7.51 7.51 7.51 6.22 5.25 3.16 1.59 TORQUE 3560 4530 7000 9330 9300 11000 12600 14300 14600 14700 14700 12600

4145HP 20.1 20.1 13.5 13.1 13.5 13.5 10.5 9.15 7.63 7.46 4.91 4.55 4.43 3.26 3.03

CTORQUE 6810 8670 16700 19100 22700 25700 24700 25600 24700 29100 23500 25900 29100 25800 29300

4155HP 20.1 20.1 20.1 15.7 15.6 14.2 11.1 10.5 9.11 8.17 6.04 5.60 4.85 4.03 3.29

TORQUE 13400 17900 24900 23000 26200 27000 26100 29300 29500 29500 29000 29500 29500 29500 29500

4160HP 21.4 21.4 17.4 16.6 16.6 15.6 13.5 10.1 8.81 8.07 6.56 5.92 4.65 3.44

DTORQUE 19000 26500 25400 28000 31600 36600 37700 32700 34400 38700 37300 38900 36800 33300

4165HP 31.3 31.3 31.3 28.8 26.5 23.4 20.9 18.0 15.1 13.4 10.5 8.82 7.63 6.35 5.17

TORQUE 20900 27800 38800 42100 44600 44600 49100 50300 48900 51200 50300 50100 50100 50200 50100

4170HP 34.2 33.5 29.2 24.9 19.6 18.0 14.9 12.5 9.80 8.58 6.76 6.20

ETORQUE 22800 41500 42600 47400 54800 58300 58200 59900 55700 56400 53400 60000

4175

HP 38.7 38.7 38.7 35.5 29.5 28.8 24.2 22.2 19.4 14.4 12.9 11.0 9.30 7.46

TORQUE 25800 47900 56500 59700 56200 67600 67600 71700 71700 69000 71700 71700 71700 71700


15/2813


SINGLE REDUCTION REDUCERS AT 1200 RPM INPUT (HP, in lbs.)

HBB CYCLOO/P RPM 57 43 31 26 23 20 16 14 12 9.8 7.9 6.7 5.8 4.8 3.9

RATIO 21 28 39 46 53 60 74 88 102 123 151 179 207 249 305

4090 HP 0.89 0.89 0.89 0.89 0.89 0.89 0.55 0.54 0.47 0.47 0.34 0.24 0.23 0.17 0.15

AATORQUE 880 1170 1630 1930 2220 2510 1930 2230 2270 2730 2400 2040 2230 2050 2130

4095HP 1.57 1.57 1.41 1.41 1.34 1.25 1.04 0.86 0.76 0.63 0.51 0.42 0.37 0.30 0.25

TORQUE 1560 2080 2600 3070 3350 3560 3650 3590 3650 3650 3650 3580 3650 3540 3650

4100HP 2.12 2.12 1.97 1.69 1.68 1.51 1.51 1.26 1.11 0.751 0.71 0.55 0.47 0.40 0.41

ATORQUE 2110 2810 3640 3680 4200 4300 5310 5250 5370 4370 5080 4660 4600 4740 5910

4105HP 3.15 3.15 3.15 2.85 2.94 2.44 2.11 1.66 1.53 1.19 1.03 0.77 0.70 0.57 0.51

TORQUE 3130 4180 5820 6210 7380 6930 7380 6930 7380 6920 7380 6540 6880 6760 7380

4110HP 4.45 4.45 4.45 4.33 4.33 3.63 3.37 2.47 2.17 1.82 1.47 1.23 1.15 0.85 0.75

TORQUE 4430 5900 8220 9430 10900 10300 11800 10300 10500 10600 10500 10500 11300 9960 10800

B 4115HP 5.82 5.82 5.83 5.64 5.70 5.19 4.21 3.54 3.06 2.53 2.06 1.74 1.51 1.13 1.02

TORQUE 5780 7710 10800 12300 14300 14800 14800 14800 14800 14800 14800 14800 14800 13300 14800

4125 HP 7.88 7.88 5.84 5.84 5.84 5.19 4.21 3.54 3.06 2.53 2.06 1.74 1.51 1.19 1.02TORQUE 7840 10400 10800 12700 14700 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800

4145HP 11.6 11.2 10.9 10.4 7.88 6.84 5.71 5.07 3.67 3.40 3.01 2.44 2.04

CTORQUE 21500 24400 27300 29500 27600 28500 27600 29500 26300 28900 29500 28800 29500

4155HP 15.1 15.1 15.1 11.8 11.7 10.4 8.31 7.08 6.11 5.07 4.13 3.48 3.01 2.50 2.04

TORQUE 15100 20100 28000 25600 29300 29500 29100 29500 29500 29500 29500 29500 29500 29500 29500

4160HP 18.4 18.4 14.9 12.6 12.6 12.6 10.2 8.61 6.30 6.30 4.95 4.24 3.73 2.92

DTORQUE 24300 33900 32400 31700 35800 44200 42400 41600 36700 45000 41900 41500 43900 42200

4165HP 23.5 23.5 20.0 17.2 17.6 14.6 12.3 10.6 8.79 7.16 6.04 5.22 4.34 3.55

TORQUE 31100 43300 43500 43100 49900 51200 51200 51200 51200 51200 51200 51200 51200 51200

4170HP 30.2 24.9 21.2 18.5 17.2 14.7 13.5 11.0 8.61 7.39 6.30 5.09 4.68

ETORQUE 55700 54300 53100 52600 60100 61400 65400 63900 61500 62600 61700 60100 67500

4175

HP 31.5 31.2 26.5 22.5 20.4 17.2 14.8 12.3 10.0 8.45 7.31 6.07 4.96

TORQUE 58200 68000 66600 64000 71600 71600 71600 71600 71600 71600 71600 71600 71600


16/2814

HELICAL BUDDYBOX REDUCER RATING TABLEINTERNATIONAL

SINGLE REDUCTION REDUCERS AT 1500 RPM INPUT (KW, Nm)

HBB CYCLOO/P RPM 71.0 54.0 39.0 33.0 28.0 25.0 20.0 17.0 15.0 12.0 10.00 8.40 7.30 6.00 4.90

RATIO 21 28 39 46 53 60 74 88 102 123 151 179 207 249 305

4090 KW 0.77 0.77 0.77 0.77 0.77 0.77 0.48 0.47 0.40 0.40 0.29 0.22 0.20 0.15 0.12

AATORQUE 92.8 124 172 203 234 265 204 237 234 282 251 226 238 214 210

4095KW 1.36 1.36 1.23 1.22 1.16 1.09 0.97 0.75 0.68 0.58 0.48 0.37 0.33 0.26 0.24

TORQUE 164 219 275 322 353 375 412 380 398 412 412 378 394 373 412

4100KW 1.85 1.85 1.72 1.47 1.46 1.32 1.32 1.10 0.97 0.66 0.62 0.48 0.41 0.35 0.35

ATORQUE 223 297 385 388 444 455 561 556 568 466 537 493 487 500 613

4105KW 2.75 2.75 2.75 2.66 2.75 2.13 1.96 1.45 1.38 1.04 0.94 0.67 0.61 0.50 0.48

TORQUE 331 442 615 702 834 733 834 732 808 734 813 692 728 714 834

4110KW 3.88 3.88 3.88 3.78 3.78 3.17 2.99 2.15 1.89 1.58 1.29 1.08 1.00 0.74 0.65

TORQUE 468 623 868 998 1140 1090 1260 1080 1100 1110 1110 1100 1180 1050 1130

B 4115KW 5.07 5.07 5.07 4.92 4.97 4.76 3.93 3.26 2.85 2.36 1.92 1.62 1.40 0.98 0.94

TORQUE 611 815 1130 1290 1510 1630 1660 1640 1660 1660 1660 1660 1660 1400 1640

4125 KW 6.88 6.88 5.10 5.09 5.09 4.84 3.93 3.30 2.85 2.36 1.92 1.62 1.40 1.04 0.94TORQUE 829 1100 1140 1340 1540 1660 1660 1660 1660 1660 1660 1660 1660 1480 1640

4145KW 10.1 9.78 9.50 9.29 6.88 5.97 4.98 4.73 3.20 2.97 2.81 2.13 1.91

CTORQUE 2260 2580 2880 3190 2920 3010 2910 3330 2770 3050 3330 3040 3330

4155KW 13.2 13.2 13.2 10.3 10.2 9.29 7.25 6.60 5.70 4.73 3.85 3.25 2.81 2.33 1.91

TORQUE 1590 2120 2950 2710 3100 3190 3070 3330 3330 3330 3330 3330 3330 3330 3330

4160KW 16.0 16.0 13.0 11.0 11.0 11.0 8.88 7.50 5.50 5.50 4.32 3.70 3.25 2.54

DTORQUE 2570 3580 3430 3340 3780 4670 4480 4390 3880 4760 4430 4390 4640 4440

4165KW 18.0 18.0 17.4 15.0 15.3 13.5 11.46 9.86 8.20 6.68 5.63 4.87 4.05 3.31

TORQUE 2890 4020 4590 4560 5260 5730 5780 5770 5780 5780 5780 5780 5780 5780

4170KW 25.0 21.8 18.5 16.1 15.0 12.9 11.8 9.56 7.50 6.45 5.50 4.45 4.08

ETORQUE 5590 5750 5620 5540 6370 6510 6900 6740 6490 6620 6530 6350 7140

4175

KW 27.5 27.3 23.1 19.7 18.8 15.8 13.8 11.5 9.30 7.90 6.80 5.70 4.60

TORQUE 6150 7200 7020 6780 7980 7970 8090 8090 8090 8090 8090 8090 8090


17/2815


DOUBLE REDUCTION REDUCER RATINGS AT 1800 RPM INPUT (HP, in lbs.)

SIZE CYCLOO/P RPM 5.04 4.25 3.59 3.11 2.64 2.22 1.88 1.61 1.36 1.09 0.92 0.79 0.70

SIZE RATIO 357 424 501 578 683 809 956 1117 1320 1656 1957 2272 2559

AA 4095DA HP 0.33 0.28 0.23 0.20 0.17 0.14 0.12 0.12 0.12 0.12 0.12 0.12 0.12

TORQUE 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650

A 4105DAHP 0.54 0.54 0.48 0.41 0.35 0.29 0.25 0.21 0.18 0.14 0.12 0.12 0.12

TORQUE 5900 7010 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380

B 4115DBHP 1.35 1.14 0.97 0.84 0.71 0.60 0.50 0.43 0.36 0.29 0.24 0.21 0.19

TORQUE 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800

C 4145DBHP 1.89 1.67 1.41 1.19 1.01 0.86 0.73 0.58 0.49 0.42 0.38

TORQUE 28900 29500 29500 29500 29500 29500 29500 29500 29500 29500 29500

D 4165DCHP 4.68 3.95 3.34 2.90 2.45 2.07 1.75 1.50 1.27 1.01 0.85 0.74 0.65

TORQUE 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200

E 4175DCHP 6.55 5.52 4.67 4.05 3.43 2.89 2.45 2.09 1.77 1.41 1.20 1.03 0.91

TORQUE 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600

SIZE CYCLOO/P RPM 0.61 0.51 0.41 0.35 0.28 0.25 0.20 0.17 0.15 0.14 0.10 0.08 0.07

SIZE RATIO 2944 3511 4365 5177 6472 7228 8880 10658 12184 13094 17966 21620 26492

AA 4095DAHP 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12

TORQUE 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650 3650

A 4105DAHP 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12

TORQUE 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380 7380

B 4115DBHP 0.16 0.14 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12

TORQUE 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800 14800

C 4145DBHP 0.33 0.27 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25 0.25

TORQUE 29500 29500 29500 29500 29500 29500 29500 29500 29500 29500 29500 29500 29500

D 4165DCHP 0.57 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

TORQUE 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200 51200

E 4175DCHP 0.79 0.67 0.54 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50 0.50

TORQUE 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600 71600

Note: MOTOR HP shown in the darker shaded areas is to overcome breakaway torque requirements in cold temperatureor high inertia applications. It is recommended that a torque limiting device be used to protect the unit or driven machine.


18/2816

FRAM E NEM A C-FACEB C E F G H I J K M P Q T

UV WSIZE ADAPTOR MAX MIN

AA409042C

AA409548C 11.02 9.09 5.51 0.20 0.79 11.87 2.20 8.31 6.18 5.51 0.12 1.06 8.54 1716 1316 4.23 4.69

56C-145TC

A410048C

A410556C-145TC 11.85 9.92 5.91 0.20 0.79 12.70 2.60 9.17 6.44 6.14 0.12 1.14 9.41 2316 11116 4.61 5.14

182-184TC

B4110 56C-145TC

B4115 182-184TC 14.49 12.05 7.48 0.20 0.98 16.10 3.39 11.42 7.97 7.24 0.12 1.22 11.65 2716 11516 5.69 6.40

B4125 213-215TC

56C-145TC

C4145 182-184TC17.24 14.88 8.66 0.20 1.18 18.84 3.82 13.39 9.53 8.70 0.12 1.61 13.62 21516 2316 6.73 7.58

C4155 213-215TC

254-256TC

56C-145TC

D4160182-184TC

D4165213-215TC 21.22 17.87 9.84 0.28 1.38 23.94 4.49 16.77 11.54 9.96 0.20 1.77 17.17 3716 2716 8.43 9.61

254-256TC

284-286TC

182-184TC

E4170

213-215TC

E4175254-256TC 24.02 20.00 11.81 0.28 1.77 26.85 5.00 18.90 13.07 10.79 0.20 1.97 19.29 31516 21516 9.45 10.71

284-286TC

324-326TC

Y d D1 DC KH N1 N2 N3 S2

3.11 0.55 2.56 5.91 3.54 1.02 1.02 1.02 M10

4.09 0.71 3.35 5.91 3.74 1.10 1.10 1.10 M12

4.49 0.71 3.94 8.03 4.33 1.26 1.26 1.34 M12

5.51 0.87 4.33 9.06 5.31 3.98 1.81 2.83 M16

6.42 1.02 5.12 11.81 6.38 3.62 2.17 3.62 M20

7.09 1.30 5.90 13.39 7.09 3.82 2.20 3.94 M20

SINGLE REDUCTIONREDUCER DIMENSIONS SIZE AA ~ E

Z

MIN.I.D.

XJ

CE(FOR 48C, 56C-143-145TC)

U Max. is Std.


NEMA C-FACEAJ AK BD BB BF BRADAPTOR

42C - 48C 3.75 3.000 4.33 .28 4

56C - 145TC 5.88 4.500 6.69 .43 4

182 - 256TC 7.25 8.500 8.98 .22 .59 4

284 - 286TC 9.00 10.500 11.10 .22 .59 4

324 - 326TC 11.00 12.500 13.86 .22 .71 4


N-S X L

LA

P P

W

V

B

J

T

H

2d

0 0

BB

Z

XU

XJ

MIN.I.D.

AKBD


19/28

XU XV KEYCE XJ Z MIN. ID WT WT2

10.87 1.78 0.47 2.44 73

.625 .98 3/16 x 3/16 x .75 11.25 2.16 0.47 2.44 59 73

11.71 2.62 0.47 4.21 77

12.08 2.16 0.47 2.44 88

.625 .98 3/16 x 3/16 x .75 12.54 2.62 0.47 4.21 77 92

13.04 3.12 0.47 5.43 95

14.67 2.62 0.47 4.21 169.750 1.38 3/16 x 3/16 15.42 3.77 0.47 5.43 141 178

x 1.02 16.04 3.99 1.09 5.43 194

17.50 2.62 0.47 4.21 273

.875 1.573/16 x 3/16 18.25 3.37 0.47 5.43 246 282

x 1.38 18.87 3.99 1.09 5.43 295

19.63 4.75 0.57 5.08 297

20.49 2.62 0.47 4.21 541

21.24 3.37 0.57 5.71 550

1.125 1.77 1/4 x 1/4 x 1.77 21.86 3.99 1.20 5.71 449 563

22.62 4.75 0.57 5.71 526

23.31 5.44 0.57 7.87 541

23.37 3.37 0.57 5.71 693

23.99 3.99 1.20 5.71 706

1.375 2.17 5/16 x 5/16 24.75 4.75 0.57 5.71 607 697

x 2.17 25.38 5.38 0.57 5.71 722

26.50 6.50 0.57 7.87 730

FRAM E NEM A C-FACELA N S x L S1 x LSIZE ADAPTOR

AA409042C

AA409548C 4.72 0 4 M10x20 M10x20

56C-145TC

A410048C

A410556C-145TC 6.10 30 6 M10x20 M12x22

182-184TC

B4110 56C-145TCB4115 182-184TC 6.89 30 6 M12x22 M16x26

B4125 213-215TC

56C-145TC

C4145 182-184TC8.35 30 6 M16x30 M20x35

C4155 213-215TC

254-256TC

56C-145TC

D4160182-184TC

D4165213-215TC 10.04 30 6 M20x35 M24x40

254-256TC

284-286TC

182-184TC

E4170213-215TC

E4175254-256TC 11.02 22.5 8 M20x35 M24x40

284-286TC

324-326TC

17

C-Face Dimensions WEIGHT (lb)

WT = Free input shaft typeWT2 = C-Face adaptor type



M

Q

I

N3

N1

S2

Y

UD1

DC

N2

E

G

XVC

CE

F

2X 3S1 X L

K

AJ KH

BR X BF


20/2818

DOUBLE REDUCTION REDUCER DIMENSIONS

Dimensions shown are for reference only and are subject to change without notice, unless certified.

Certified prints are available after receipt of an order; consult factory.

NEMA C-FACEAJ AK BD BB BF BRADAPTOR

56C - 145TC 5.88 4.500 6.69 .43 4

182 - 256TC 7.25 8.500 8.98 .22 .59 4

FRAM E NEM A C-FACEB C E F G H I J K M P Q T

UV WSIZE ADAPTOR MAX MIN

AA4095DA 56C-145TC 11.02 10.72 5.51 0.20 0.79 11.87 2.20 8.31 6.18 5.51 0.12 1.06 8.54 1.44 1.19 4.23 4.69

A4105DA 56C-145TC 11.85 11.87 5.91 0.20 0.79 12.70 2.60 9.17 6.44 6.14 0.12 1.14 9.41 2.19 1.69 4.61 5.14

B4115DB 56C-145TC 14.49 14.11 7.48 0.20 0.98 16.10 3.39 11.42 7.97 7.24 0.12 1.22 11.65 2.44 1.94 5.69 6.40

C4145DB 56C-145TC 17.24 16.55 8.66 0.20 1.18 18.84 3.82 13.39 9.53 8.70 0.12 1.61 13.62 2.9 2.19 6.73 7.58

56C-145TC

D4165DC

182-184TC

21.22 19.84 9.84 0.28 1.38 23.94 4.49 16.77 11.54 9.96 0.20 1.77 17.17 3.44 2.44 8.43 9.61

56C-145TC

E4175DC

182-184TC

24.02 21.26 11.81 0.28 1.77 26.85 5.00 18.90 13.07 10.79 0.20 1.97 19.29 3.94 2.94 9.45 10.71

Y d D1 DC KH N1 N2 N3 S2

3.11 0.55 2.56 5.91 3.54 1.02 1.02 1.02 M10

4.09 0.71 3.35 5.91 3.74 1.10 1.10 1.10 M12

4.49 0.71 3.94 8.03 4.33 1.26 1.26 1.34 M12

5.51 0.87 4.33 9.06 5.31 1.81 1.81 2.83 M16

6.42 1.02 5.12 11.81 6.38 1.97 2.17 3.62 M20

7.09 1.30 5.90 13.39 7.09 1.97 2.20 3.94 M20

U Max. is Std.


BB

Z

XU

XJ

AKBD

CE(FOR 182184TC)

MIN.I.D.

2 d

LA

V

B

H

P J

T

P

W

NS X L

Z

XJ

MIN.I.D.

AKBD

CE(FOR 56C, 143145TC)


21/2819

FRAM E NEM A C-FACELA N S x L S1 x LSIZE ADAPTOR

AA4095DA 56C-145TC 4.72 0 4 M10x20 M10x20

A4105DA 56C-145TC 6.10 30 6 M10x20 M12x22

B4115DB 56C-145TC 6.89 30 6 M12x22 M16x26

C4145DB 56C-145TC 8.35 30 6 M16x30 M20x35

56C-145TC

10.04 30 6 M20x35 M24x40D4165DC

182-184TC

56C-145TC

11.02 22.5 8 M20x35 M24x40E4175DC

182-184TC


WT = Free input shaft typeWT2 = C-Face adaptor type

Dimensions shown are for reference only and are subject to change without notice, unless certified.

Certified prints are available after receipt of an order; consult factory.

D1 U

Y

DC

E

M

Q

F

G

C

N3S2

XV

CE

N2

N1

2X 3S1 x L

AJ

BR X BF

K

KH

XU XV KEYCE XJ Z MIN. ID WT WT2

.625 .98 3/16 x 3/16 x .75 13.29 2.62 0.47 4.21 62 70

.625 .98 3/16 x 3/16 x .75 14.43 2.62 0.47 4.21 81 89

.750 1.38 3/16 x 3/16x 1.02 16.74 2.62 0.47 4.21 156 1.64

.875 1.57 3/16 x 3/16 x 1.38 19.18 2.62 0.47 4.21 259 267

22.47 2.62 0.47 4.21 484

1.125 1.77 1/4 x 1/4 x 1.77

23.43 3.37 0.47 5.43

471

488

23.89 2.62 0.47 4.21 706

1.375 2.17 5/16 x 5/16 x 2.17

24.85 3.37 0.47 5.43

614

6970

C-Face Dimensions WEIGHT (lb)


22/2820

GENERAL CONSTRUCTION HELICAL GEAR CASE

REF DESCRIPTION REF DESCRIPTION

1 Casing 14 Retaining Ring (External)

2 Cover 15 Pinion Shaft Spacer

3 Gear 16 Hex Socket Head Plug

4 Hex Head Bolt 17 Ball Bearing

5 Spring Washer 18 Oil Seal

6 Ball Bearing 19 Pinion Shaft

7 Retaining Ring (Internal) 20 Ball Bearing

8 Oil Seal 21 Retaining Ring (Internal)

9 Taper-Grip Bushing 22 Retaining Ring (External)

10 Bushing Screw 23 Seal Cap

11 Thrust Plate 24 Key (Square End)

12 Pinion Shaft Spacer 25 Output Hub

13 Pin Carrier 26 Hex Socket Head Plug


23/2821

MIXER DRIVES

The new SM-Helical Buddybox parallel, offset reduceris also available as an application series mixer drive.This quality, high-performance mixer is available withtapered roller bearings, integral flange (face mount) andeither a keyed output hub or standard Taper-Grip

bushing system.

Also featured is our superior new drywell design, whichoffers the ultimate customer benefit, to prevent leakageand process contamination problems.

Please consult our factory for additional details on

Helical Buddybox mixer drives from Sumitomo.

PARALLEL OFFSET CYCLO (HBB)REDUCERS & GEARMOTORS

s 6 sizes offered

s Ratios from 18:1 toover 2,000:1

s Flange mountingoption

s Wide range ofmounting options:Flange, Foot/Angle

Bracket, or Housings Solid Shaft, Keyed

Hollow Bore, orKeyless Taper GripBushing offered

s High efficiency helicalgearing combined withproven strengthand durabilityof SM-CYCLO speedreducer

s Integral motoror C-Faceadapter input

DRYWELL DESIGN

s Offered in SM-Helical Buddybox sizes C, D and E.(Sizes AA B are grease lubricated.)

Oil

Level

New Drywell Option


24/2822

LUBRICATION

SM-Helical Buddybox reducers and gearmotors areshipped without oil. Before running, they should befilled with the appropriate amount of the correctlubricant for their mounting position-see Tables L-1 andL-2. Please consult the factory for additional

information not covered here.

Helical

BuddyboxOutput side (HBB) Input side (Cyclo)

Size Y1 Y2 Y3 Y4 Y5 Y6 Y1 Y2 Y3 Y4 Y5 Y6

AA 0.16 0.16 0.13 0.16 0.29 0.26 G G G G G G

A 0.21 0.24 0.18 0. 24 0.40 0.37 G G G G G G

B 0.26 0.40 0.26 0.40 0.53 0.48 G G G G G G

C 0.45 0.55 0.34 0.55 1.24 0.92 0.11 0.11 0.11 0.11 G G

D 0.71 0.92 0.53 0.92 1.85 1.45 0.18 0.18 0.18 0.18 G G

E 0.92 1.11 0.66 1.11 2.38 1.85 0.24 0.24 0.24 0.24 G G

Table L-2 Oil Quantity (In gallons)

Oil Replenishment and Change Interval

a) Maintain proper oil levels at all times.

b) Check oil quantity every 2500 hours. If the oil iscontaminated, burned or waxed, change the oilimmediately and flush if necessary.

c) Under normal operating conditions, Sumitomorecommends an oil change every 5000 hours ofoperation. The intervals should not exceed 2 years.

d) An oil change after the first 500 hours of operation ishighly recommended.

e) If the unit will be running in a high ambient, highhumidity, or corrosive environment, the lubricant willhave to be changed more frequently. Consult thefactory for recommendations.

f) The Cyclo portion and helical portion must be filledwith oil separately. Oil does not flow from onesection to the other.

Ambient 14F-32F 32F-95F 95F-122F

Temp. (-10C-0C) (0C-35C) (35C-50C)

Viscosity @ 61.2 - 74.8 90 - 165 198 - 50640C (104F) cST

ISO Viscosity68 100 - 150 220 - 460

Grade

AGMA2EP 3EP 4EP 5EP 7 EP

Viscosity Grade

Viscosity @ 100F284 - 347 417 - 765 916 - 2719

(38C) SSU

Table L-1 Recommended Oil forSM Helical Buddybox & Cyclo

Y1

Y2

Y3

q Oil Drain Plug

V Oil Overflow Plug (Oil Level) Oil Fill Plug

Y4Note: Overflow is located next to drain on bottom.

Y5

Y6*Note: For flange units, the Y is replaced with an F.

Mounting Positions*


25/2823

STANDARD INTEGRAL MOTOR CHARACTERISTICS

Standard Wiring Diagram 208, 230/460V

Illustrated below are the wiring diagrams for our standard motor. For additional information please refer to motor name plate. Dueto changes in design features, this diagram may not always agree with that on the motor. If different, the motor diagram foundinside the conduit box cover is correct.

Y-Connected (5 HP and smaller) Delta-Connected (712 HP and larger)

Motor Characteristics

The SM-Helical Buddybox gearmotorsfull load ratings and amperage can befound below in table M-1. These ratingsare based on the motors design

values. If additional information isrequired, please consult factory.

Table M-1 230/460 Volt, Synchronous Speed 1800 rpm, 60 Hz, Continuous Duty, TEFC

Full Load Full Load CurrentAmperage

Starting CurrentAmperage

Torque% of F.L.

*Code letter shown is for 230V or 460V operation. Consult factory for other voltages.

Line 208/230V 60HzLine 208/230V 60Hz Line 460V 60Hz Line 208/230V 60HzLine 208/230V 60Hz Line 460V 60Hz

Effi- Power InertiaFrame

TorqueBreak-

ciency Factor Code WR2HPSize

rpm in. lb. 230V 460V 208V 230V 460V Starting down % %Letter* lb. ft2

1/2 F-71M 1740 18.3 2.1 1.1 2.0 9.8 4.9 295 280 71.9 65.1 J 0.0154

3/4 F-80S 1730 27.4 2.5 1.2 2.5 12.3 6.2 266 245 76.9 73.0 H 0.0227

1 F-80 1750 36.0 3.4 1.7 3.4 17.6 8.8 269 303 77.2 72.3 H 0.0285

1.5 F-90S 1730 54.7 4.6 2.3 4.7 28.6 14.3 273 281 80.3 74.1 J 0.0451

2 F-90L 1740 72.5 6.0 3.0 6.2 36.8 18.4 263 270 82.3 75.6 J 0.0504

3 F-100L 1730 109 8.4 4.2 8.7 54.8 27.4 277 266 84.4 77.2 J 0.0789

5 F-112M 1730 183 13.0 6.5 13.7 91.5 45.8 308 279 86.3 82.4 J 0.201

7.5 F-132S 1710 277 18.1 9.0 20.1 120 61 223 221 86.7 88.2 H 0.271

10 F-132M 1740 361 23.6 11.8 26.4 147 73.5 212 214 89.6 88.9 G 0.635

15 F-160M 1740 542 34.3 17.2 38.2 231 115 248 221 90.5 89.0 G 0.891

20 G-160L 1740 725 45.8 22.9 51 272 136 222 220 91.6 89.9 F 2.13

25 G-180M 1770 891 57 28.4 63 343 171 199 235 92.6 88.2 F 5.34

30 G-180M 1760 1075 68 34.2 77 388 194 192 226 91.5 88.1 F 5.34


26/2824

TORQUE ARM INFORMATION

The HBB housing allows for a wide variety of torque armsupport options. Torque arm support should be selectedbased on the space restrictions and structural com-ponents available on the driven machinery. Some optionsare shown below. Example A is a factory stocked option,

B through E are not normally stocked.

Note: Consult factory or torque arm brochure for dimensional drawings and application assistance.

B.

A.

C.

D. E.


27/28

Torque Arm Application Examples

MexicoSM-CYCLO DE MEXICO, S.A. DE C.V.Calle C No. 506A, Parque Industrial AlmacentroApodaca, N.L., Mexico 66600011-52-8-369-3697/8 FAX: 011-52-8-369-3699

Central & South America Sales,Engineering, Stocking & AssemblyBrazilSM-CYCLO REDUTORES DO BRASIL, LTDA.

Av. Dr. Ulysses Guimares, 353309990-080 Diadema, So Paulo, Brazil011-55-11-445-4388 FAX: 011-55-11-456-2922

ChileSM-CYCLO DE CHILE LTDA.Napoleon 3565, Of. 510Las Condes, Santiago, Chile011-56-2-203-7300 FAX: 011-56-2-203-7195

Headquarters and ManufacturingSumitomo Machinery Corporation of America

4200 Holland Boulevard, Chesapeake, VA 23323 (757) 485-3355 FAX: (757) 485-3075Toll Free 1-800-SM-CYCLO Web: http://www.smcyclo.com E-mail: [email protected]

Mid-West175 West Lake DriveGlendale Heights, IL 60139

(630) 752-0200 FAX: (630) 752-0208West2375 Railroad Street, Corona, CA 91720(909) 340-4100 FAX: (909) 340-4108

Southwest1420 Halsey Way #130, Carrollton, TX 75007(972) 323-9600 FAX: (972) 323-9308

Northeast501 Office Center Dr., Suite 260Ft. Washington, PA 19034(215) 653-0560 FAX: (215) 653-0181

Southeast4200 Holland BoulevardChesapeake, VA 23323(757) 485-3355 FAX: (757) 487-3193

Canadian Stocking& Assembly FacilitiesToronto (East)SM-CYCLO OF CANADA, LTD.870A Equestrian CourtOakville, Ontario, Canada L6L 6L7(905) 469-1050 FAX: (905) 469-1055

British Columbia (West)SM-CYCLO OF CANADA, LTD.740 Chester Road, Annacis Island, DeltaB.C., Canada V3M 6J1(604) 525-5403 FAX: (604) 525-0879

MontrealSM-CYCLO OF CANADA, LTD.226 Migneron StreetSt. Laurent, Quebec, Canada H4T 1Y7(514) 340-1300 FAX: (514) 340-1343

North American Regional OfficesStocking & Assembly Facilities

ISO 9001

CER

TIFIED

Clevis Type

SMA Standard

(Bushing) Type

Bracket TypeT-Type


28/28

S U M IT O M O Q u a D e l t a P R O G R A M

P r o vid ing

T H E A V A ILA B L E S O L U T IO N , W O R L D W ID E

v G E A R B O X E S

v M O T O R S

v C O N T R O L L E R S

v C O N C E N T R I C

v P A R A L L E L O F F S E T

v R I G H T A N G L E

v C O N S T A N T S P E E D

v M E C H A N I C A L V S

v E L E C T R I C A L V S

v T H E A M E R I C A S

v A S I A

v E U R O P E

SPEED REDUCER

SM-CYCLO

Concentric

GEARMOTOR

SM-CYCLO

Concentric

LOW RATIO PLANETARY

SM-CYCLOConcentric

PRECISION CYCLO

Concentric

SHAFT MOUNTSPEED REDUCER

SM-SHAFT MOUNTParallel Offset

BEVEL GEARMOTOR

SM-BEVEL BUDDYBOX

Right Angle

PARTS & SERVICE

WORLDWIDE



WORM GEARMOTOR

SM-ULYSSES

Right Angle

ALL

DRIVES

ALL

TYPES

ALL

SPEEDS

WORLD-WIDE

SHAFT MOUNTGEARMOTOR

SM-HYPONICRight Angle



DOUBLE ENVELOPINGWORM GEAR

SM-HEDCONRight Angle

ELECTRICALVARIABLE SPEED

AF-3100 NTAC-2000AC Drive AC Drive

MECHANICALVARIABLE SPEED

SM-BEIER

SHAFT MOUNTEDGEARMOTOR

SM-HELICAL BUDDYBOXParallel Offset

HELICALGEAR REDUCER

PARAMAXParallel Offset& Right Angle

Power Transmission Products4200 Holland Blvd., Chesapeake, VA 23323(757) 485-3355 FAX: (757) 485-3075

Toll Free: 1-800-SM-CYCLOWeb: http://www.smcyclo.com E-mail: [email protected]

ISO9001

CERTIFI

ED

DISTRIBUTED BY:

cyclo hbb catalogsumitomo

Documents